Speed Box S Manual - Pro
Contents
1. 10 DEL BY PRO JECT AUDIO SYSTEMS INSTRUCTIONS FOR USE Pro Ject Speed Box S Dear music lover thank you for purchasing a PRO JECT AUDIO Speed Box The unit permits electronic speed change of your Pro Ject record player between 33 and 45 r p m and also permits the replay of shellac records by allowing 78 r p m with an appropriate pulley and cartridge In order to achieve maximum performance and reliability you should study these instructions for use carefully V Warning of a hazard for the user the unit or possible misuse nies Important notice Safety instructions AC outlet voltages vary from country to country Before connecting to the mains make sure that the voltage in your area meets the voltage requirements printed on the power supply The power supply is used to disconnect the unit from the mains Make sure that the power supply is easily accessible at all times Never handle the device the power supply while your hands are wet or damp Avoid letting liquids enter the device or the power supply Never place any item containing liquid such as a flower vase on or near the device Never spill any liquid on the device or the power supply Never place any naked flame sources such as lighted candles on or near the device The product shall not be used in damp or wet locations next to a bathtub sink swimming pool or any other similar conditions Connecting the record player Power CE rons E SM EEE Pro Ject Au2. dio Systems Vienna Austria oo Connect the power cable supplied polarity to the socket Output 16V and to the power supply socket of the record player The original power supply of the record player is then no longer required V Make all connections whilst the Speed Box is disconnected from the power supply Models with 16V AC wall power supply only 16V 190mA AC max All Juke Box Elemental and Debut Carbon models all Phono and Phono USB models all models 5 with Automatic switch off like Debut Ill E and electronic speed change like Debut Carbon Esprit SB RPM 6 1 SB Xpression Ill Comfort Xperience Comfort Xtension all models and Signature may not be used with the Speed Box Mains power connection Connect the low voltage plug from the power supply to the socket Power 18V before connecting the power supply to the mains V Never use any other power supply than the one supplied with the unit 2 O Audio Trade GmbH Pro Ject Speed Box S Revision 2013 10 23 To switch on from standby or to standby The push button on the left hand side will toggle the Speed Box between its fully operational status and standby The blue LED above the stand by push button shows that the unit is switched on Speed selection 33 45 r p m O 33 45 Speed Box S The belt must be on the smaller 50Hz models larger 60Hz models diameter part of the motor pulley Press the button 33 45 to swi
3. for damage caused by not adhering to these instructions for use Modification or change to any part of the product by unauthorized persons release the manufacturer from any liability over and above the lawful rights of the customer Copyright trademarks PRO JECT is a Registered Trademark of H Lichtenegger The information was correct at the time of going to A press The manufacturer reserves the right to make This guide was produced by Audio Trade GmbH changes to the technical specification without prior Copyright 2012 All rights reserved notice as deemed necessary to uphold the ongoing process of technical development 4 Audio Trade GmbH Pro Ject Speed Box S Revision 2013 10 23
4. he belt Replace the platter 78 r p m is not available with all Juke Box Elemental Essential and Debut Carbon models all Phono and Phono USB models all models with Automatic switch off like Debut III E Xperience Basic 2 Xperience Comfort 2 Xperience Acryl 2 Xperience Classic 2 Xperience SuperPack 6 PerspeX 15 6 PerspeX SuperPack RPM 1 3 Genie RPM 9 1 RPM 9 1 SuperPack RPM 9 1 Acryl RPM 9 2 Evolution RPM 10 1 Evolution and Signature The models Debut III Phono SB 1 Xpression III Comfort RPM 5 SuperPack RPM 5 1 SuperPack RPM 6 1 SB RPM 6 1 SB SuperPack and Xtension are equipped with the 78 r p m pulley as a standard O Audio Trade GmbH Pro Ject Speed Box S Revision 2013 10 23 3 Technical specifications Pro Ject Speed Box S Nominal speeds 33 and 45 r p m Optional 78 r p m Quartz oscillator Speed stability 0 001 Length power cable approximately 40cm Turntable connection 16V AC 190mA max 3W power consumption max Outboard power supply 18V 500mA DC suitable for your country s mains supply Dimensions W x H x D D with sockets 103 x 36 x 104 104 mm Weight 560g without power supply Service Should you encounter a problem which you are not able to alleviate or identify please contact your dealer for further advice Only when the problem cannot be resolved there should the unit be sent to the responsible distributor in your country Warranty The manufacturer accepts no responsibility
5. tch between 33 and 45 r p m The selected speed is shown respectively by the lit LED To play at 45 or 78 r p m please always start the turntable at 33 r p m and then switch to the higher speed when it has attained full speed Replay at 78 r p m In order to replay shellac records at 78 r p m your turntable must be equipped with the 78 r p m pulley which is available as an optional accessory for most models Atter fitting the 78 r p m pulley please proceed as follows Remove the platter and using the tool from the accessory kit fit the belt around the larger diameter step of the pulley Replace the Platter start the turntable at 33 r p m and switch the speed to 45 r p m the platter will then revolve at 78 r p m Fitting the 78 r p m pulley Before beginning work fit the cartridge s needle protection cover Remove the platter and drive belt Please remember that sweat or sticky fingers will impair the function of the belt Use a piece of kitchen paper or a cloth to remove the belt Measure the height of the pulley above the plinth in order to ease correct refitting Using a small screwdriver loosen the grub screw in the neck of the pulley just enough to remove the pulley vertically without using force Refit the pulley in the opposite order Tighten the grub screw carefully making sure you do not overtighten it Fit the drive belt around the subplatter and the pulley Again use a piece of paper or cloth to avoid soiling t
Download Pdf Manuals
Related Search