AEG LS 72840 Washing machine User Guide Manual
Contents
1. Downloaded From WashingMachine Manual com Manuals Installation 5 Fill the smaller upper hole and the two large ones with the corresponding plas tic plug caps supplied in the bag con taining the instruction booklet Positioning and levelling Install the machine on a flat hard floor Make sure that air circulation around the machine is not impeded by carpets rugs etc Before placing it on small tiles apply a rubber coating Never try to correct any unevenness in the floor by putting pieces of wood cardboard or similar materials under the machine If it is impossible to avoid positioning the machine next to a gas cooker or coalburning stove an in sulating panel covered with aluminium foil on the side facing the cooker or stove must be inserted between the two appliances The machine must not be installed in rooms where the temperature can drop below 0 C The water inlet hose and the drain hose must not be kinked Please ensure that when the appliance is installed it is easily accessible for the engineer in the event of a breakdown Carefully level by screwing the adjustable feet in or out Never place cardboard wood or similar materials under the machine to compensate for any unevenness in the floor Water inlet An inlet hose is supplied and can be found inside the machine drum This appliance must be connected to a cold2. Any electrical work required to install this appliance should be carried out by a qualified electrician or competent person Use This appliance is designed for domestic use It must not be used for purposes other than those for which it was designed Only wash fabrics which are designed to be machine washed Follow the instructions on each garment label e Do not overload the appliance See the Washing Programme Table e Before washing ensure that all pockets are empty and buttons and zips are fastened Avoid washing frayed or torn articles and treat stains such as paint ink rust and grass before washing Underwired bras must NOT be machine washed Garments which have been in contact with volatile petroleum products should not be machine washed If volatile cleaning fluids are used care should be taken to ensure that the fluid is removed from the garment before placing in the machine Never pull the power supply cable to remove the plug from the socket always take hold of the plug itself Never use the appliance if the power supply cable the control panel the working surface or the base are damaged so that the inside of the washing machine is accessible Child Safety e This appliance is not intended for use by person including children with reduced physi cal sensory or mental capabilities or lack of experience and knowledge unless they have been given supervision or instruction concerning use of the appliance by a pers
3. and the washing programmes see chapter Wash ing Programmes PREWASH option Select this option if you wish your laundry to be prewashed at 30 C before the main wash The Prewash ends with a short spin in programmes for cotton and synthetic fabrics where as in the programmes for delicate fabrics the water is only drained The relevant symbol will appear on the display This option is recommended for heavily soiled laundry STAIN option Select this option to treat heavily soiled or stained laundry with stain remover extended main wash with time optimized stain action phase The relevant symbol will appear on the display This option is not available with a temperature lower than 40 C If you wish to perform a programme with the stain option pour stain remover into stain compartment marked with an arrow SENSITIVE option By selecting this option the washing intensity will be reduced The machine adds one rinse in the programmes for cottons and synthetics The relevant symbol will appear on the dis play This option cannot be selected together with Extra Rinse option This option is recommended for non fast coloured items and for frequently washed items Downloaded From WashingMachine Manual com Manuals Daily use EXTRA RINSE option additional rinse This appliance is designed for saving water However for people with a very delicate skin allergic to detergents it may be necessary to rinse the laundry usi
4. it was interrupted press the button 7 again If you have chosen a delayed start the machine will begin the countdown f an incorrect option is selected the yellow pilot light of the button 7 blinks 3 times and he message Err is displayed for a few seconds Select the DELAY START button 8 Before you start the programme if you wish to delay the start press the button repeat edly to select the desired delay The corresponding symbol will appear on the display The wash programme can be delayed from 30 min 60 min 90 min 2 hours and then by 1 hour up to a maximum of 20 hours by means of this button The selected delay time value will appear on the display for about 3 seconds then the dura tion of the programme will appear again You must select this option after you have set the programme and before you press the button 7 You can modify or cancel the delay time at any moment before you press the button 7 The door will be locked throughout the delay time If you wish to add laundry in the ma chine during the delay time press the button 7 to set the machine to pause When the Door symbol disappears the door can be opened Add the laundry close the door and press the button 7 again Downloaded From WashingMachine Manual com Manuals Daily use Selecting the delayed start e Select the programme and the required options e Select the delay start e Press button 7 the appliance starts its hourly countdown The programm
5. manufacturers instructions on quantities to use Use less detergent if e you are washing a small load e the laundry is lightly soiled e large amounts of foam form during washing Downloaded donotusazastons oventiicial silk ianual com Manuals Care and cleaning Degrees of water hardness Water hardness is classified in so called degrees of hardness Information on hardness of the water in your area can be obtained from the relevant water supply company or from your local authority If the water hardness degree is medium or high we suggest you to add a water softener following always the manufacturer s instructions When the degree of hardness is soft readjust the quantity of the detergent CARE AND CLEANING You must DISCONNECT the appliance from the electricity supply before you can carry out any cleaning or maintenance work Descaling The water we use normally contains lime It is a good idea to periodically use a water soft ening powder in the machine Do this separately from any laundry washing and according to the softening powder manufacturer s instructions This will help to prevent the forma tion of lime deposits After each wash Leave the door open for a while This helps to prevent mould and stagnant smells forming inside the appliance Keeping the door open after a wash will also help to preserve the door seal Maintenance wash With the use of low temperature washes it is possible to get a build u
6. tap off and refer to your Serv ice Centre to replace the hose Water drainage The end of the drain hose can be positioned in three ways 1 Hooked over the edge of a sink using the plastic hose guide supplied with the machine In this case make sure the end cannot come unhooked when the machine is emptying This could be done by tying it to the tap with a piece of string or attaching it to the wall 2 Ina sink drain pipe branch This branch must be above the trap so that the bend is at least 60 cm above the ground 3 Directly into a drain pipe at a height of not less than 60 cm and not more than 90 cm The end of the drain hose must always be ventilated i e the inside diameter of the drain pipe must be larger than the outside diameter of the drain hose The drain hose must not be kinked Downloaded From WashingMachine Manual com Manuals Electrical connection A 6 ono Go A The drain hose may be extended to a maximum of 4 metres An additional drain hose and joining piece is available from your local Service Centre ELECTRICAL CONNECTION Information on the electrical connection is given on the rating plate on the inner edge of the appliance door Check that your domestic electrical installation can
7. the appliance in order that the new owner can get to know the functioning of the appli ance and the relevant warnings e You MUST read them carefully before installing or using the appliance e Before first starting up check the appliance for any damage incurred during transport Never connect up a damaged appliance If parts are damaged contact your supplier e If the appliance is delivered in the winter months when there are minus temperatures Store it at room temperature for 24 hours before using for the first time General safety e It is dangerous to alter the specifications or attempt to modify this product in any way e During high temperature wash programmes the door glass may get hot Do not touch it e Make sure that small pets and children do not climb into the drum To avoid this please check into the drum before using e Any objects such as coins safety pins nails screws stones or any other hard sharp ma terial can cause extensive damage and must not be placed into the machine e Only use the advised quantities of fabric softener and detergent Damage to the fabric can ensue if you over fill Refer to the manufacturer s recommendations of quantities e Wash small items such as socks laces washable belts etc in a washing bag or pillow case as it is possible for such items to slip down between the tub and the inner drum e Do not use your washing machine to wash articles with whalebones material without hems or torn ma
8. HOLD NIGHT CYCLE PREWASH STAIN SENSITIVE EXTRA RINSE TIME SAVING 2 SPIN REDUCTION RINSE HOLD PREWASH EXTRA RINSE SPIN REDUCTION RINSE HOLD NIGHT CYCLE PREWASH STAIN EXTRA RINSE TIME SAVING 2 SPIN REDUCTION RINSE HOLD NIGHT CYCLE PREWASH STAIN EXTRA RINSE we Wy Ww ly wa ly wg ly B HW Washing programmes Programme Maximum and Minimum Temperature rp F Detergent Cycle Description Maximum Fabrics Load Type of Options Laundry Compartment DELICATE RINSES SPIN REDUCTION amp Rinses Short spin RINSE HOLD aximum spin speed NIGHT CYCLE ax load 6 kg EXTRA RINSE With this programme it is possible to rinse and spin delicate garments which have been washed by hand The machine performs some rinses followed by a fi nal spin DRAIN Draining of water ax load 6 kg For emptying out the water of the last rinse in pro grammes with the RINSE HOLD or NIGHT CYCLE op ion selected SPIN SPIN REDUCTION Drain and long spin at the maximum speed ax load 6 kg Separate spin for hand washed cotton garments and after programmes with the RINSE HOLD or NIGHT CY CLE option selected Before selecting this programme he selector dial must be turned to O DUVETS SPIN REDUCTION Wy 40 30 amp ain wash Rinses Short spin at 800 rpm ax load 2 kg Special program for one sleeping bag one duvet or wo pillowcases or washable coats padded with syn hetic fil
9. LAVAMAT LS 70840 LS 72840 User manual Washing Machine Downloaded From WashingMachine Manual com Manuals Contents Thank you for choosing one of our high quality products To ensure optimal and regular performance of your appliance please read this instruction manual carefully It will enable you to navigate all processes perfectly and most efficiently To refer to this manual any time you need to we recommend you to keep it in a safe place And please pass it to any future owner of the appliance We wish you much joy with your new appliance OPERATING INSTRUCTIONS 3 Interrupting a programme 13 SAFETY INFORMATION 3 E poran 13 the door after the programme has General safety 3 pening Installation 4 e 13 se 4 t the end of the programme 13 Child Safety 4 WASHING PROGRAMMES 14 PRODUCT DESCRIPTION 5 HELPFUL HINTS AND TIPS 18 Detergent dispenser drawer 6 Sorting out the laundry 18 CONTROL PANEL 6 Before loading the laundry 18 Umoe 7 Removing stains 18 y i Detergents and additives 19 FIRST USE 8 Quantity of detergent to be used 19 PERSONALIZATION 8 Degrees of water hardness 20 Acoustic signals 8 CARE AND CLEANING 20 Child safety lock 8 Descaling 20 DAILY USE 9 After each wash 20 Load the laundry 9 aintenance wash 20 Measure out the detergent and the fabric External cleaning 20 softener 9 Detergent dispenser drawer 20 Turn the programme dial 1 to set the Drain pump a 21 required p
10. ain remover into the compartment marked with an arrow 2 If required pour fabric softener into the compartment marked the amount used must not exceed the MAX mark in the drawer Close the drawer gently Downloaded From WashingMachine Manual com Manuals BO Daily use Turn the programme dial 1 to set the required programme You can choose the right programme for any type of laundry following the descriptions on the washing programme tables see Washing Programmes Turn the programme dial to the required programme The programme dial determines the type of washing cycle e g water level drum movement number of rinses and the washing temperature according to the type of laundry The light of button 7 starts blinking and the display shows the duration of the selected pro gramme The programme dial can be turned either clockwise or anticlockwise Position CE Reset programme Switching OFF of the machine At the end of the programme the selector dial must be turned to position to switch the machine off i If you turn the programme selector dial to another programme when the machine is work ing the yellow pilot light of button 7 will blink 3 times and the message Err is displayed on the display to indicate a wrong selection The machine will not perform the new selected programme Select the desired TEMPERATURE Button 2 i When selecting a programme the appliance automatical
11. ative It can vary depending on the quantity and the type of laundry on the temperature of the water supply and on the ambient temperature Standard programmes for the Energy Label consumption values The cotton 60 C economy and cotton 40 C economy are the standard cotton programmes Downloaddgrmemmaly sailed cotton Jaundny hnewaensuitablesto clean normally soiled cotton laundry Installation and they are the most efficient programmes in terms of combined energy and water con sumption for washing that type of cotton laundry They agree with EN60456 i The actual water temperature may differ from the declared cycle temperature INSTALLATION INSTRUCTIONS INSTALLATION Unpacking All transit bolts and packing must be removed before using the appliance You are advised to keep all transit devices so that they can be refitted if the machine ever has to be transported again 1 After removing all the packaging care fully lay machine on it s back to remove the polystyrene base from the bottom Downloaded From WashingMachine Manual com Manuals Installation 2 Remove the power supply cable and the draining and inlet hose from the hose holders on the rear of the appliance W K 3 Unscrew the three bolts with the key supplied with the appliance 4 Slide out the relevant plastic spacers
12. c tion containers Ecological hints To save water energy and to help protect the environment we recommend that you follow these tips e Normally soiled laundry may be washed without prewashing in order to save detergent water and time the environment is protected too e The machine works more economically if it is fully loaded With adequate pre treatment stains and limited soiling can be removed the laundry can then be washed at a lower temperature Measure out detergent according to the water hardness the degree of soiling and the quantity of laundry being washed Downloaded From WashingMachine Manual com Manuals www aeg com shop e A e 4 32957911 A 262011 Downloaded From WashingMachine Manual com Manuals CE
13. d safety lock This device permits you to leave the appliance unattended and not to worry that children might be injured by or cause damage to the appliance This function remains able also when the washing machine is not working To enable or disable this option press simultaneously for about 6 seconds buttons 4 and 5 until the Child Lock symbol appears on or disappears from the display There are two different ways to set this option e Before pressing button 7 it will be impossible to start the machine e after pressing button 7 it will be impossible to change any other programme or option Downloaded From WashingMachine Manual com Manuals Daily use B DAILY USE Load the laundry 1 Open the door by carefully pulling the door handle outwards Place the laundry in the drum one item at a time shaking them out as much as possible 2 Close firmly the door You must hear a click during closing WARNING Do not embed the laundry between the door and the rubber joint Measure out the detergent and the fabric softener Your new appliance was designed to reduce water energy and detergent consumption 1 Pull out the dispenser drawer until it stops Measure out the amount of de tergent required pour it into the main wash compartment yy and if you wish o carry out the prewash phase pour the detergent into the compartment marked uy If you wish to perform the stain func tion pour the st
14. d then when remains 1 hour the time decreases every minute e Incorrect option selection Ifan option which is not compatible with the set wash programme is selected the message Err is displayed for about 2 seconds and the yellow light of button 7 starts blinking e Alarm codes In the event of operating problems some alarm codes can be displayed for example Ef see chapter What to do if e End of the programme When the programme has finished a blinking zero 7 is displayed the DOOR symbol disappears and the door can be opened 9 8 DELAY START 4 symbol 9 9 CHILD SAFETY LOCK amp symbol FIRST USE i e Ensure that the electrical and water connections comply with the installation instruc tions e Remove the polystyrene block and any material from the drum e Before the first wash run a cotton cycle at the highest temperature without any laundry in the machine to remove any manufacturing residue from the drum and tub Pour 1 2 a measure of detergent into the main wash compartment and start the machine PERSONALIZATION Acoustic signals The machine is provided with an acoustic device which sounds in the following cases e at the end of the cycle e in the event of operating problems By pressing the 3 and 4 buttons simultaneously for about 6 seconds the acoustic signal is deactivated except for the events of operating problems By pressing these two buttons again the acoustic signal is reactivated Chil
15. dry in the drum when spinning as well as increased stability of the machine The machine makes an unusual noise Machines based on modern technology operate No water is visible in the drum very economically using very little water with out affecting performance Anti flooding system has activated e Pull out the plug from the power socket close the water tap and contact the Service Force Centre The display shows the alarm code EF 7 Downloaded From WashingMachine Manual com Manuals Technical data If you are unable to identify or solve the problem contact our service centre Before telephoning make a note of the model serial number and pur chase date of your machine the Service Centre will require this information Mod Prod No Ser No TECHNICAL DATA Dimensions Width 60 cm Height 85cm Depth 45 cm Electrical connection Information on the electrical connection is given on the rating plate on the inner edge of the appliance door Water supply pressure Minimum 0 05 MPa Maximum 0 8 MPa Maximum Load Cotton 6kg Spin Speed Maximum 1000 rpm LS 70840 1200 rpm LS 72840 CONSUMPTION VALUES tre White Cottons 95 C 1 95 62 Cottons 60 C 116 58 Cottons 40 C 0 75 58 Synthetics 40 C 0 5 50 Delicates 40 C 0 5 58 Wool Handwash 30 C 0 28 42 1 Refer to the display for the programme time 2 The consumption information shown in this chart is indic
16. e will start after the selected delay has expired Cancelling the delayed start e Set the washing machine to PAUSE by pressing the button 7 e Press button 8until the symbol 7 is displayed e Press the button 7 again to start the programme A The selected delay can be changed only after selecting the washing programme again The Delay Start can not be selected with Drain programme Altering an option or a running programme It is possible to change some options before the programme carries them out Before you make any change you must pause the washing machine by pressing the button 7 Changing a running programme is possible only by resetting it Turn the programme se lector dial to O and then to the new programme position Start the new programme by pressing the 7 button again The washing water in the tub will not emptied out Interrupting a programme Press the button 7 to interrupt a programme which is running the corresponding light starts blinking Press the button again to restart the programme Cancelling a programme Turn the selector dial to O to cancel a programme which is running Now you can select a new programme Opening the door after the programme has started When the machine is working and throughout the delay time the door is locked If for any reason you wish to open the door set firstly the machine to pause by pressing the button 7 e f the DOOR symbol blinks and after a few minutes disappears the d
17. for washing heavily soiled sport items The machine will add automatically a prewash phase before the main wash to eliminate mud stains We recommend you to put the NO deter gent into the ty compartment of the detergent drawer 20 MIN 3KG 30 Main wash Rinses Short spin Maximum spin speed Max load 3 kg Special programme at 30 C duration 20 Minutes Suitable for fabrics that needs to be freshen up only worn once sport items lightly soiled or new fabrics QUICK INTENSIVE 60 40 Main wash Rinses Long spin Maximum spin speed Max load 5 kg Quick washing programme to be used for lightly soiled white fast coloured cottons Downloaded From WashingMachine Manual com Manuals Options SPIN REDUCTION RINSE HOLD NIGHT CYCLE SPIN REDUCTION RINSE HOLD EXTRA RINSE SPIN REDUCTION RINSE HOLD NIGHT CYCLE EXTRA RINSE SPIN REDUCTION SPIN REDUCTION RINSE HOLD EXTRA RINSE Detergent Compartment Wy Wy E DE E Helpful hints and tips Programme Maximum and Minimum Temperature oe j 3 y Detergent A Description Maximum Fabrics Load Type of Options Compartment aundry COTTON ECONOMY SPIN REDUCTION yy 3 60 RINSE HOLD yy Main wash Rinses Long spin NIGHT CYCLE amp Maximum spin speed PREWASH Max load 6 kg STAIN White and fast coloured cotton SENSITIVE This programme can be selected for slightly or nor EXTRA RINSE mally soiled cotton items The tempe
18. fresh stains with cold water For dried stains soak overnight in water with a special detergent then rub in the soap and water Oil based paint moisten with benzine stain remover lay the garment on a soft cloth and dab the stain treat several times Dried grease stains moisten with turpentine lay the garment on a soft surface and dab the stain with the fingertips and a cotton cloth Downloaded From WashingMachine Manual com Manuals Helpful hints and tips JR Rust oxalic acid dissolved in hot water or a rust removing product used cold Be careful with rust stains which are not recent since the cellulose structure will already have been damaged and the fabric tends to hole Mould stains treat with bleach rinse well whites and fast coloureds only Grass soap lightly and treat with bleach whites and fast coloureds only Ball point pen and glue moisten with acetone lay the garment on a soft cloth and dab the stain Lipstick moisten with acetone as above then treat stains with methylated spirits Treat any residual marks with bleach Red wine soak in water and detergent rinse and treat with acetic or citric acid then rinse Treat any residual marks with bleach Ink depending on the type of ink moisten the fabric first with acetone then with acetic acid treat any residual marks on white fabrics with bleach and then rinse thoroughly Tar stains first treat with stain remover methylated spirits or benzine then rub
19. in the hose with a stiff brush 4 Screw the hose back onto the tap Make sure the connection is tight 5 Unscrew the hose from the machine Keep a rug nearby because some water may flow 6 Clean the filter in the valve with a stiff brush or with the piece of cloth Downloaded From WashingMachine Manual com Manuals Care and cleaning 7 Screw the hose back to the machine and make sure the connection is tight 8 Turn on the water tap Emergency emptying out If the water is not discharged proceed as follows to empty out the machine 1 pull out the plug from the power socket close the water tap if necessary wait until the water has cooled down open the pump door place a bowl on the floor and place the end of the emergency emptying hose into the bowl Remove its cap The water should drain by gravity into the bowl When the bowl is full put the cap back on the hose Empty the bowl Repeat the procedure until water stops flowing out 6 clean the pump if necessary as previously described 7 replace the emergency emptying hose in its seat after having plugged it 8 screw the pump again and close the door oe CoN Frost precautions If the machine is installed in a place where the temperature could drop below 0 C proceed as follows 1 close the water tap and unscrew the water inlet hose from the tap 2 place the end of the emergency emptying hose and that of the i
20. ling or dawns WOOL PLUS HANDWASH SPIN REDUCTION Uy 40 Cold RINSE HOLD amp ain wash Rinses Short spin NIGHT CYCLE aximum spin speed ax load 2 kg Washing programme for machine washable wool as well as for hand washable woollens and delicate fab rics Note A single or bulky item may cause imbal ance If the appliance doesn t perform the final spin phase add more items redistribute the load manually and then select the spinning programme LINGERIE HANDWASH SPIN REDUCTION wiy 40 Cold RINSE HOLD amp Main wash Rinses Short spin NIGHT CYCLE Maximum spin speed Max load 1 kg This programme is suitable for very delicate items as lingerie bras and underwear etc Downloaded From WashingMachine Manual com Manuals Washing programmes Programme Maximum and Minimum Temperature Cycle Description Maximum Fabrics Load Type of Laundry SILK HANDWASH 30 Cold Main wash Rinses Short spin Maximum spin speed Max load 1 kg Delicate washing programme suitable for silk and mixed synthetic items OUTDOOR SPORTS 40 Cold Main wash Rinses Short spin at 800 rpm Maximum spin speed Max load 2 5 kg Special program for waterproof sports and outdoor clothing even those with a waterproof membrane Please don t use any fabric softener SPORT INTENSIVE 40 Cold Prewash Main wash Rinses Short spin Maximum spin speed Max load 2 5 kg This programme is suitable
21. ly proposes the default tempera ture provided for that programme Press this button repeatedly to increase or decrease the temperature if you want your laundry to be washed at a temperature different from the one proposed by the washing machine The symbol of cold wash corresponds to i For the maximum and the minimum available wash water temperature see Washing pro grammes Select the spin speed NIGHT CYCLE or RINSE HOLD option button 3 i When the required programme has been selected your appliance automatically proposes the maximum spin speed provided for that programme Press this button repeatedly to change the spin speed if you want your laundry to be spun at a speed different from the one proposed by the washing machine RINSE HOLD by selecting this option the water of the last rinse is not emptied out to pre vent the fabrics from creasing At the end of the programme and RINSE HOLD symbol appear on the display DOOR symbol door locked remains lit the pilot light of button 7 goes off and the door is blocked to indicate that the water must be emptied out NIGHT CYCLE by selecting this option the machine will not drain the water of the last rinse so as not to wrinkle the laundry As all spinning phases are suppressed this washing cycle is very noiseless and it can be selected at night or in times with a more economical power rate In some programmes the rinses will be performed with more water At the e
22. nd of the programme 7 and RINSE HOLD symbol appear on the display the DOOR symbol re mains lit the pilot light of button 7 goes off and the door is blocked to indicate that the water must be emptied out Downloaded From WashingMachine Manual com Manuals Daily use B To empty out the water please read chapter At the end of the programme Programme option buttons Depending on the programme different functions can be combined A WARNING Not all the options are compatible among themselves The symbols of the incompatible op tions disappear Anyway if an option which is not compatible with the set washing programme or any oth er option is selected the Err message is displayed for few seconds and the yellow pilot of button 7 light starts blinking You must select the options after you have selected the programme but before pressing the button 7 Press the button 4 all the option symbols appear on the display To scroll all the available options press the button 4 The corresponding symbol appears on the display and starts blinking Press the button 5 to activate and confirm your choice A black dash appears under the selected symbol to indicate that this option has been set Press the same button to deacti vate the option After selecting the options wait about few seconds until the display gets back to the de fault status The selected options appear on the display i For the compatibility among the options
23. ng an extra quantity of water extra rinse The relevant symbol will appear on the display and this option is active for selected washing programme If you wish to activate this option permanently press simultaneously buttons 2 and 3 for some seconds the relevant symbol appears on the display If you wish to cancel it press the same buttons until the symbol disappears Select the TIME SAVING option button 6 This option allows you to modify the washing time automatically proposed by the appli ance By pressing this button you can select the following options DAILY by pressing button 6 once the corresponding symbol appears on the display and the washing duration will be reduced to wash daily soiled laundry Reduced washing time is presented on the display SUPER QUICK by pressing button 6 twice the corresponding symbol remains lit on the dis play and the washing duration will be reduced to wash lightly soiled laundry or items that have been used or worn for a short time Reduced washing time is presented on the display Select the START PAUSE button 7 To start the selected programme press the button 7 the corresponding red pilot light stops blinking The DOOR symbol appears on the display to indicate that the appliance has started operat ing and the door is locked To interrupt a programme which is running press the button 7 the corresponding red pilot ight starts blinking To restart the programme from the point at which
24. nlet hose in a bowl placed on the floor and let water drain out 3 screw the water inlet hose back on and reposition the emergency emptying hose after having put the cap on again By doing this any water remaining in the machine is removed avoiding ice forming and consequently damage to the appliance When you use the machine again make sure that the ambient temperature is above 0 C JN Every time you drain the water through the emergency emptying hose you must pour 2 litres of water into the main wash compartment of the detergent drawer and then run the drain programme This will activate the ECO Valve device avoiding that part of the deter gent remains unused at next washing Downloaded From WashingMachine Manual com Manuals What to do if WHAT TO DO IF Certain problems are due to lack of simple maintenance or oversights which can be solved easily without calling out an engineer Before contacting your local Service Centre please carry out the checks listed below During machine operation it is possible that the yellow pilot light of button 7 blinks one of the following alarm codes appears on the display and at the same time some acoustic sig nals sound every 20 seconds to indicate that the machine is not working e EJO problem with the water supply EQ problem with the water draining e FU door open e FFE anti flooding system has activated Once the problem has been eliminated press the button 7 to resta
25. nnection The drain filter is clogged EP 7 e Clean the drain filter An option or a programme that ends with the The machine does not empty and or does not water still in the tub or a that eliminates all the spin spinning phases has been selected e Select the draining or the spinning pro gramme The laundry is not evenly distributed in the drum e Redistribute the laundry Too much detergent or unsuitable detergent creates too much foam has been used e Reduce the detergent quantity or use anoth er one Check whether there are any leaks from one of the inlet hose fittings It is not always easy to see this as the water runs down the hose check to see if it is damp e Check the water inlet hose connection The drain or the inlet hose is damaged e Replace it with a new one The cap on the filter has not been replaced or the filter has not been properly screwed in after cleaning action e Refit the cap on the filter or screw the filter There is water on the floor fully in Too little detergent or unsuitable detergent has been used e Increase the detergent quantity or use an other one Stubborn stains have not been treated prior to washing Unsatisfactory washing results e Use commercial products to treat the stub born stains The correct temperature was not selected Check if you have selected the correct tem perature Excessive laundry load e Reduce the laundry load The prog
26. nual com Manuals Care and cleaning 3 Open the pump door 4 Place a container close to the pump to collect any spillage 5 Release the emergency emptying hose place it in the container and remove its cap cover 6 When no more water comes out un screw the pump and remove it Always keep a rag nearby to dry up spillage of water when removing the pump Downloaded From WashingMachine Manual com Manuals Care and cleaning 8 Put the cap back on the emergency emptying hose and place the latter back in its seat 9 Screw the pump fully in 10 Close the pump door A WARNING When the appliance is in use and depending on the programme selected there can be hot water in the pump Never remove the pump cover during a wash cycle always wait until the appliance has finished the cycle and is empty When replacing the cover ensure it is securely retightened so as to stop leaks and young children being able to remove it Cleaning the water inlet filters AN If the appliance doesn t fill takes long to fill water the starting button blinks yellow or the display if available shows the relevant alarm see chapter What to do if for more de tails check if the water inlet filters are blocked To clean the water inlet filters 1 Turn off the water tap 2 Unscrew the hose from the tap 3 Clean the filter
27. nuals Washing programmes Programme Maximum and Minimum Temperature Detergent Compartment Cycle Description Maximum Fabrics Load Type of Options Laundry JEANS 60 Cold ain wash Rinses Long spin aximum spin speed ax load 3 kg This program fits for Jeans clothing and dark col oured laundry The Extra Rinse option will be activa ed automatically SYNTHETICS 60 Cold ain wash Rinses Short spin aximum spin speed ax load 3 kg Reduced load 1 5 kg Synthetic or mixed fabrics underwear coloured garments non shrink shirts blouses EASY IRON PLUS 60 Cold Main wash Rinses Short spin Maximum spin speed Max load 1 5 kg Easy care textiles will be treated gentle in order to avoid wrinkles In many cases ironing will be no lon ger necessary Hint Remove textiles immediately af ter program end DELICATES 40 Cold Main wash Rinses Short spin Maximum spin speed Max load kg 3 Reduced load kg 1 5 Delicate garments made of Acrylics Poliamide or Pol yester like curtains or delicate clothing VISCOSE 40 Cold Main wash Rinses Short spin Maximum spin speed Max load kg 3 Special gentle programme for fabrics such a viscose cupro lyocell It performs an cleaning action more in tensive than the handwash programme Downloaded From WashingMachine Manual com Manuals SPIN REDUCTION RINSE HOLD NIGHT CYCLE PREWASH SPIN REDUCTION RINSE
28. on re sponsible for their safety e The packaging components e g plastic film polystyrene can be dangerous to children danger of suffocation Keep them out of children s reach e Keep all detergents in a safe place out of children s reach Downloaded From WashingMachine Manual com Manuals Product description e Make sure that children or pets do not climb into the drum To prevent children or pets becoming trapped inside the drum the ma chine incorporates a special feature To acti vate this device rotate the button without pressing it inside the door clockwise until D the groove is horizontal If necessary use a coin To disable this device and restore the possibility of closing the door rotate the ie button anticlockwise until the groove is ver tical PRODUCT DESCRIPTION Your new appliance meets all modern requirements for effective treatment of laundry with low water energy and detergent consumption The ECO VALVE system allows total use of detergent and reduces water consumption so saving energy a m O CF 23 6 Detergent dispenser drawer Control panel Door opening handle Rating plate Drain pump E Adjustable feet Downloaded From WashingMachine Manual com Manuals HES Control panel Detergent dispenser drawer uy Compartment for prewash phase or stain re mover The prewash detergent is added at the beginning of the
29. oor can be opened e f the DOOR symbol doesn t go off it means that the machine is already heating or that the water level is too high In this case the door cannot be opened e f you cannot open the door but you need to open it you have to switch the machine off by turning the selector dial to O After a few minutes the door can be opened pay attention to the water level and temperature After closing the door it is necessary to select the programme again and to press button 7 At the end of the programme The machine stops automatically the light of button 7 goes off A blinking 7 appears on the display and the acoustic signal sounds for some minutes If you have chosen a programme or an option that ends with water in the tub follow the below instruction to empty the water out The drum continues to run at regular intervals until the water draining Downloaded From WashingMachine Manual com Manuals Washing programmes To empty the water out turn the programme selector dial to O set the DRAINING or SPINNING programme if needed press the relevant button to reduce the spin speed press the button 7 when the programme has finished the display shows a blinking On the display the DOOR symbol disappears The door can be opened Turn the programme selector dial to O to switch the machine off Remove the laundry from the drum and carefully check that the drum is empty If you do not intend to carry out ano
30. p of residues inside the drum We recommend that a maintenance wash be performed on a regular basis To run a maintenance wash e The drum should be empty of laundry e Select the hottest cotton wash programme e Use a normal measure of detergent must be a powder with biological properties External cleaning Clean the exterior cabinet of the appliance with soap and water only and then dry thor oughly JN Do not use methylated spirits solvents or similar products to clean the cabinet Detergent dispenser drawer The detergent dispenser drawer should be cleaned regularly The washing powder and additive dispenser drawer should be cleaned regularly Downloaded From WashingMachine Manual com Manuals Care and cleaning Remove the drawer by pressing the catch downwards and by pulling it out Flush it out under a tap to remove any traces of accumulated powder 2 To aid cleaning the top part of the addi tive compartment should be removed Clean all parts with water 3 Clean the chamber of dispenser drawer with a brush Drain pump The pump should be inspected regularly and particularly if e the machine does not empty and or spin e the machine makes an unusual noise during draining due to objects such as safety pins coins etc blocking the pump Proceed as follows 1 Disconnect the appliance 2 If necessary wait until the water has cooled down Downloaded From WashingMachine Ma
31. ramme is still running e Wait the end of washing cycle The door lock has not been released The door will not open e Wait until the symbol 9 5 has gone off There is water in the drum e Select drain or spin programme to empty out the water Downloaded From WashingMachine Manual com Manuals What to do if The transit bolts and packing have not been re moved e Check the correct installation of the appli ance The support feet have not been adjusted The machine vibrates or is noisy Check the correct levelling of the appliance The laundry is not evenly distributed in the drum e Redistribute the laundry Maybe there is very little laundry in the drum e Load more laundry The electronic unbalance detection device has cut in because the laundry is not evenly distrib uted in the drum The laundry is redistributed by reverse rotation of the drum This may hap pen several times before the unbalance disap Spinning starts late or the machine does not pears and normal spinning can resume If after spin some minutes the laundry is still not evenly distributed in the drum the machine will not spin e The laundry load is perhaps to little add more items redistribute the load manually and then select the spinning programme The machine is fitted with a type of motor which makes an unusual noise compared with other traditional motors This new motor en sures a softer start and more even distribution of the laun
32. rature will de crease and the washing time will be extended This al lows to obtain a good washing efficiency so saving energy O off For cancelling the programme which is running or to switch the machine off 1 Stain option can be selected only at the temperature of 40 C or higher 2 If you select the Super Quick option by pressing button 6 we recommend that you reduce the maximum load as indicated Full loading is possible however with somewhat reduced cleaning results 3 If using liquid detergents a programme without prewash must be selected HELPFUL HINTS AND TIPS Sorting out the laundry Follow the wash code symbols on each garment label and the manufacturer s washing in structions Sort the laundry as follows whites coloureds synthetics delicates woollens Before loading the laundry Never wash whites and coloureds together Whites may lose their whiteness in the wash New coloured items may run in the first wash they should therefore be washed separately the first time Button up pillowcases close zip fasteners hooks and poppers Tie any belts or long tapes Remove persistent stains before washing Rub particularly soiled areas with a special detergent or detergent paste Treat curtains with special care Remove hooks or tie them up in a bag or net Removing stains Stubborn stains may not be removed by just water and detergent It is therefore advisable to treat them prior to washing Blood treat
33. rogramme 0 Cleaning the water inlet filters 23 Select the desired TEMPERATURE Button 2 Emergency emptying out 24 0 Frost precautions 24 Select the spin speed NIGHT CYCLE or RINSE WHAT TO DO IF 25 HOLD option button 3 10 TECHNICAL DATA 28 Programme option buttons 11 PREWASH option 4 CONSUMPTION VALUES 28 STAIN option 1 INSTALLATION INSTRUCTIONS 29 SENSITIVE option 1 EXTRA RINSE option additional rinse 2 a Select the TIME SAVING option button 6 npaceng 2 Positioning and levelling 31 Select the START PAUSE button 7 12 Hl ane Select the DELAY START button 8 2 iit ie a Altering an option or a running programme arer Sena 3 ELECTRICAL CONNECTION 34 Downloaded From WashingMachine Manual com Manuals 295791 1 A 262011 Safety information ENVIRONMENT CONCERNS 34 Ecological hints 35 Packaging materials 35 Subject to change without notice OPERATING INSTRUCTIONS Z N SAFETY INFORMATION JN Read carefully amp keep for future reference e The safety of Your appliance complies with the industry standards and with legal re quirements on the safety of appliances However as manufacturers we feel it is our duty to provide the following safety notes e tis most important that this instruction book should be retained with the appliance for future reference Should the appliance be sold or transferred to another owner or should you move house and leave the appliance always ensure that the book is supplied with
34. rt the programme If af ter all checks the problem persists contact your local Service Centre The door has not been closed EY e Close the door firmly The plug is not properly inserted in the power socket e Insert the plug into the power socket There is no power at the socket e Please check your domestic electrical instal lation The main fuse has blown The washing machine does not start e Replace the fuse The selector dial is not correctly positioned and the button 7 has not been pressed e Please turn the selector dial and press the button 7 again The delay start has been selected e lf the laundry is to be washed immediately cancel the delay start The Child safety lock has been activated e Deactivate this device The water tap is closed E10 e Open the water tap The inlet hose is squashed or kinked E77 e Check the inlet hose connection The filter in the inlet hose or the inlet valve fil ter are blocked EJ 7 Clean the water inlet filters See Cleaning the water inlet filters for more details The door is not properly closed EGF Close the door firmly The machine does not fill The end of the drain hose is too low The machine fills then empties immediately Refer to relevant paragraph in Water drain age section Downloaded From WashingMachine Manual com Manuals What to do if The drain hose is squashed or kinked FPfF e Check the drain hose co
35. s under the washing phase symbol of the run ning programme At the end of each washing phase the line under the corresponding symbol becomes fixed i If the OVERDOSAGE symbol lights up at the end of the programme it indicates that too much detergent has been used 9 4 Options PREWASH _ J STAIN 4 SENSITIVE EXTRA RINSE 9 5 DOOR 0 symbol Door locked e This symbol indicates if the door can be opened the symbol is on the door cannot be opened The appliance is performing a washing programme the symbol is blinking the door is opening the symbol is off the door can be opened The washing programme is finished 9 6 TIME SAVING option symbol 9 7 The display shows the following information e Duration of the selected programme After selecting a programme the duration is displayed in hours and minutes for ex ample 2 9S The duration is calculated automatically on the basis of the maximum recommended load for each type of fabric After the programme has started the time remaining is updated every minute e Delay start The selected delay 20 hours max set by means of the relevant button appears on the display for about 3 seconds for example 9f7 then the duration of the previously selected programme is displayed Downloaded From WashingMachine Manual com Manuals BE First use The DELAY START symbol will appear on the display The delay time value decreases by one unit every hour an
36. take the maximum load required also taking into account any other appliances in use WARNING Connect the machine to an earthed socket WARNING The manufacturer does not accept any responsibility for damage or injury through failure to comply with the above safety precaution WARNING The power supply cable must be easily accessible after installing the machine WARNING Should the appliance power supply cable need to be replaced this must be carried out by a Service Centre gt P PP ENVIRONMENT CONCERNS The symbol R on the product or on its packaging indicates that this product may not be treated as household waste Instead it should be taken to the appropriate collection point for the recycling of electrical and electronic equipment By ensuring this product is disposed of correctly you will help prevent potential negative consequences for the environment and human health which could otherwise be caused by inappropriate waste handling of this product For more detailed information about recycling of this product please contact your local council your household waste disposal service or the shop where you purchased the product Downloaded From WashingMachine Manual com Manuals Packaging materials The materials marked with the symbol amp are recyclable gt PE lt polyethylene gt PS lt polystyrene gt PP lt polypropylene This means that they can be recycled by disposing of them properly in appropriate colle
37. terial e Always unplug the appliance and turn off the water supply after use cleaning and main tenance e Under no circumstances should you attempt to repair the machine yourself Repairs car ried out by inexperienced people may cause injury or serious malfunctioning Contact your local Service Centre Always insist on genuine spare parts wnloaded From WashingMachine Manual com Manuals Safety information Installation e This appliance is heavy Care should be taken when moving it e When unpacking the appliance check that it is not damaged If in doubt do not use it and contact the Service Centre All packing and transit bolts must be removed before use Serious damage can occur to the product and to property if this is not adhered to See relevant section in the user manual e After having installed the appliance check that it is not standing on the inlet and drain hose and the worktop is not pressing the electrical supply cable against the wall e If the machine is situated on a carpeted floor please adjust the feet in order to allow air to circulate freely under the appliance e Always be sure that there is no water leakage from hoses and their connections after the installation e If the appliance is installed in a location subject to frost please read the dangers of freezing chapter Any plumbing work required to install this appliance should be carried out by a qualified plumber or competent person
38. ther wash close the water tap Leave the door open to prevent the formation of mildew and unpleasant smells WASHING PROGRAMMES Programme Maximum and Minimum Temperature Ae 3 Detergent S Description Maximum Fabrics Load Type of Options Compartment aundry COTTONS LINEN SPIN REDUCTION uy 3 95 Cold RINSE HOLD Wy Main wash Rinses Long spin NIGHT CYCLE amp Maximum spin speed PREWASH Max load 6 kg Reduced load 3 kg STAIN 1 White and coloured cotton normally soiled items SENSITIVE EXTRA RINSE TIME SAVING 2 HYGIENE SPIN REDUCTION yy 3 60 RINSE HOLD ly Main wash Rinses Long spin PREWASH amp Maximum spin speed STAIN Max load 6 kg The washing programme for white cottons This pro gram eliminates the microorganisms thanks to the washing by 60 C and an additional rinse In this way he action is more effective Put into the compart ment Stain a special additive for hygiene and select he option Stain 40 60 MIX SPIN REDUCTION Uy 3 40 RINSE HOLD Wy ain wash Rinses Long spin NIGHT CYCLE amp aximum spin speed PREWASH ax load 6 kg STAIN White and coloured cotton This programme can be SENSITIVE used for laundry which should be washed at 40 C or EXTRA RINSE 60 C separately The maximum load capacity can be put into the drum in order to save energy and water The same good washing result will be obtained as for normal programme at 60 C Downloaded From WashingMachine Manual com Ma
39. wash programme The stain remover is added during the STAIN Ac tion phase in the main wash uy Compartment for powder or liquid detergent used for main wash Compartment for liquid additives fabric soft ener starch Follow the product manufacturer s recommendations on quantities to use and do not ex ceed the MAX mark in the detergent dispenser drawer Any fabric softener or starching additives must be poured into the compartment before starting the wash programme CONTROL PANEL i Below is a picture of the control panel It shows the programme selector dial as well as the buttons and the display These are presented by relevant numbers on the following pages BHEHA G u g Programme selector dial TEMPERATURE button TEMPERATUR SPIN reduction button U MIN OPTIONS button OPTION OK button OK E TIME SAVING button ZEITSPAREN START PAUSE button START PAUSE Downloaded From WashingMachine Manual com Manuals Display Ei DELAY START button ZEITVORWAHL EJ Display Symbols Handwash amp Child Lock DISPLAY 9 1 Temperature indicator and COLD symbol 9 2 Spin Speed indicator RINSE HOLD Ky NIGHT CYCLE symbols 9 3 Programme progress display PREWASH 1y MAIN WASH u RINSE PING DRAIN ys OVERDOSAGE P e The programme progress display shows the washing phases of the selected programme e During a washing cycle a black line blink
40. water supply Do not use the hose from your previous machine to connect to the water supply Downloaded From WashingMachine Manual com Manuals Installation 1 Open the porthole and extract the inlet hose 2 Connect the hose with the angled con nection to the machine Do not place the inlet hose downwards Angle the hose to the left or right de pending on the position of your water tap 3 Set the hose correctly by loosening the ring nut After positioning the inlet hose be sure to tighten the ring nut again to prevent leaks 4 Connect the hose to a tap with a 3 4 thread Always use the hose supplied with the appliance The inlet hose must not be lengthened If it is too short and you do not wish to move the tap you will have to purchase a new longer hose specially designed for this type of use Installation should comply with local water authority and building regulations require ments Check the minimum water pressure required for safe operation of the appliance in the chapter Technical Data Downloaded From WashingMachine Manual com Manuals Installation Water stop device The inlet hose is provided with a water stop de vice which protects against damage caused by water leaks in the hose which could develop due to natural ageing of the hose This fault is shown by a red sector in the window A Should this oc cur turn the water
41. with de tergent paste Detergents and additives Good washing results also depend on the choice of detergent and use of the correct quan tities to avoid waste and protect the environment Although biodegradable detergents contain substances which in large quantities can up set the delicate balance of nature The choice of detergent will depend on the type of fabric delicates woollens cottons etc the colour washing temperature and degree of soiling All commonly available washing machine detergents may be used in this appliance e powder detergents for all types of fabric e powder detergents for delicate fabrics 60 C max and woollens e liquid detergents preferably for low temperature wash programmes 60 C max for all types of fabric or special for woollens only The detergent and any additives must be placed in the appropriate compartments of the dispenser drawer before starting the wash programme If using liquid detergents a programme without prewash must be selected Your appliance incorporates a recirculation system which allows an optimal use of the con centrated detergent Follow the product manufacturer s recommendations on quantities to use and do not ex ceed the MAX mark in the detergent dispenser drawer Quantity of detergent to be used The type and quantity of detergent will depend on the type of fabric load size degree of soiling and hardness of the water used Follow the product
Download Pdf Manuals
Related Search