Home

10 - Taurus

1. AN The gases around the battery can explode if exposed to flames sparks or lit cigarettes An explosion could result in injury or vehicle damage Batteries contain sulfuric acid which burns skin eyes and clothing 132 Maintenance and care yn Applying too much pressure on the ends when lifting a battery could cause acid to spill Lift the battery with a carrier or with your hands on the opposite corners Servicing your battery The low maintenance battery has removable vent caps for checking electrolyte level and adding water Check electrolyte level every 24 months or 40 000 km 24 000 miles in an average temperature of 32 C 90 F Keep the electrolyte level in each cell up to the level indicator Do not overfill If the level gets low refill the battery with distilled water If necessary distilled water may be substituted with tap water that is not hard or has a high mineral or alkali content If the battery needs water quite often have the charging system checked for a possible malfunction Because your vehicle s engine is electronically controlled by a computer some control conditions are maintained by power from the battery When the battery is disconnected or a new battery is installed the engine must relearn its idle conditions before you vehicle will drive properly To begin this process 1 Put the gearshift in P Park turn off all accessories and start the vehicle 2 Let the engine idle for
2. 3 Use a 7 mm wrench to turn the vertical adjusting screw until the reference mark on the reflector extension aligns with the 0 reference mark on the vertical indicator when viewed directly from above 4 Close the hood CLEANING AND CARING FOR YOUR VEHICLE Refer to the Customer Assistance Guide for a list of Ford approved cleaners polishes and waxes Washing your vehicle Wash your vehicle regularly with cold or lukewarm water Never use strong detergents or soap If your vehicle is particularly dirty use a quality car wash detergent Always use a clean sponge washing glove or similar device and plenty of water for best results To avoid spots avoid washing when the hood is still warm immediately after or during exposure to strong sunlight During winter months it is especially important to wash the vehicle on a regular basis Large quantities of dirt and road salt are difficult to remove and they also cause damage to the vehicle Remove any 151 Maintenance and care exterior accessories such as antennas before entering a car wash e After washing apply the brakes several times to dry them Waxing your vehicle The best way to determine when the paintwork needs waxing is by noting when water stops beading on the surface This could be every three or four months depending on operating conditions Use only carnauba or synthetic based waxes Remove any bugs and tar before waxing vehicl
3. 2 Go to the front of the vehicle and release the auxiliary latch that is located under the front center of the hood Lift the hood until the lift cylinders hold it open IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 3 0L Vulcan engine 120 Maintenance and care 1 Automatic transaxle fluid dipstick 2 Brake fluid reservoir 3 Air filter assembly 4 Battery 5 Engine oil filler cap 6 Engine oil dipstick 7 Power steering fluid reservoir 8 Engine coolant reservoir 9 Windshield washer fluid reservoir 3 0L Duratec engine 1 Automatic transaxle fluid dipstick 2 Brake fluid reservoir 3 Air filter assembly 4 Battery 5 Engine oil filler cap 6 Engine oil dipstick 7 Engine coolant reservoir 121 Maintenance and care 8 Windshield washer fluid reservoir 9 Power steering fluid reservoir 3 4L SHO engine J Gees pI N E ANNAN aS RARR f I fe uL ve 32 VALVE j Automatic transaxle fluid dipstick Brake fluid reservoir Air filter assembly Battery Engine oil dipstick Engine oil filler cap Engine coolant reservoir Windshield washer fluid reservoir Power steering fluid reservoir O OMANDUKRWN 122 Maintenance and care CHECKING AND ADDING ENGINE OIL Checking the engine oil Check the engine oil each time y
4. Cruise control if equipped This light comes on CRUISE when the cruise control ON button is pressed It turns off when the cruise control OFF button is pressed or when the ignition is turned to the OFF position Brake system warning Extinguishes when the parking brake is released Illumination BRAKE after releasing the parking brake indicates low brake fluid level Engine oil pressure When the oil pressure is below the normal 7 operating range this lamp will illuminate The engine oil level being too high or too low could cause this lamp to illuminate This lamp will come on when the ignition is first turned on but then should turn off If the lamp stays on continued operation will cause severe engine damage Charging system Briefly illuminates nee when the ignition is turned on and the engine is off The light also illuminates when the battery is not charging properly requiring electrical system service Air bag readiness Briefly illuminates when the ignition is turned on and the engine is off If the Instrumentation light fails to illuminate continue to flash or remains on have the system serviced immediately Headlamps on warning chime Sounds when the headlamps are on the ignition is off and the key is not in the ignition and the driver s door is opened Key in ignition warning chime Sounds when the key is left in the ignition in the OFF LOCK or ACC position and the dr
5. Fuel gauge Displays approximately how much fuel is in the fuel tank when the key is in the ON position The fuel gauge may vary slightly when the vehicle is in motion The ignition should be in the OFF Instrumentation position while the vehicle is being refueled 13 Controls and features TURNING ON THE INTERIOR AND EXTERIOR LAMPS Panel dimmer control Instrument panel illumination interior O Pe OT Ce lamps and cargo lamp brightness can be adjusted with this control Move the thumbwheel up to brighten the lamps or down to dim the lamps Headlamp control Turn the headlamp Sn control one turn to PE N DIM LAMP turn on the parking 0 2 lamps Turn it all the 26 6 way to turn on the headlamps Autolamp delay system if equipped The autolamp system sets the headlamps to turn on and off automatically You can use the autolamps to e Turn on the lamps automatically at night Turn off the lamps automatically in daylight Keep the lamps on for up to three minutes after the ignition is turned off Setting autolamp 1 Make sure headlamp control is in the OF F position then turn the key to ON or start the vehicle 14 Controls and features 2 Locate autolamp thumbwheel and turn O Pe POM LNP thumbwheel to beginning of MAX position The indicator light will come on if it is dark e
6. VEHICLE At times you may want to tow your vehicle behind another vehicle such as a recreational vehicle car or a truck Before you have your vehicle towed e Release the parking brake e Move the gearshift to N Neutral e Turn the key in the ignition to OFF e Unlock the steering wheel Do not tow your vehicle at a speed faster than 56 km h 35 mph or for a distance greater than 80 km 50 miles unless the drive wheels are placed on dollies A Never use a tow bar that attaches to the bumper when you tow your vehicle This could damage the bumper and cause an accident 117 Maintenance and care SERVICE RECOMMENDATIONS To help you service your vehicle e We highlight do it yourself items in the engine compartment for easy location e As possible we design parts that can be replaced without tools e We provide you with a Service Guide which makes tracking routine service for your vehicle easy If your vehicle requires professional service your dealership can provide necessary parts and service Check your Warranty Information Booklet to find out which parts and services are covered Use only recommended fuels lubricants fluids and service parts conforming to specifications Motorcraft parts are designed and built to provide the best performance in your vehicle Precautions when servicing your vehicle Be especially careful when inspecting or servicing your vehicle Here are some general pre
7. children sit where they can be properly restrained AN It is extremely dangerous to ride in a cargo area inside or outside of a vehicle In a collision people riding in these areas are more likely to be seriously injured or killed Do not allow people to ride in any area of your vehicle that is not equipped with seats and safety belts Be sure everyone in your vehicle is in a seat and using a safety belt properly Combination lap and shoulder belts 1 To fasten insert the tongue into the slot in Lo the buckle eNO 2 To unfasten push lt the red release button Lo and remove the tongue from the buckle The outboard safety restraints in the vehicle are combination lap and shoulder belts The front and rear seat passenger outboard safety belts have two types of locking modes described below 55 Seating and safety restraints To test the vehicle sensitive emergency locking mode pull the shoulder belt quickly to lock The vehicle sensitive mode is the normal retractor mode adjusting shoulder belt tightness in response to vehicle movement For example if the driver brakes suddenly or turns a corner sharply or the vehicle receives an impact of 8 km h 5 mph or more the combination safety belts would lock to help reduce forward movement of the driver and passengers Automatic locking mode In this mode the shoulder belt is locked in a certain position by the occupant and does not adjust ti
8. open and close windows When AUTO is pressed and released quickly the driver s window will open completely without holding the switch down Each passenger has window controls The window lock feature allows only the driver to operate the power windows POWER DOOR LOCKS IF EQUIPPED Press U to unlock all doors and L to lock all doors 30 Controls and features Central locking Two step unlocking When unlocking the driver or front passenger door with the Key turn it once toward the front of the vehicle to unlock that door only Turn the key a second time to unlock all doors When locking turn the key toward the back of the vehicle to lock all doors Liftgate wagon only The power liftgate lock is located on the right inside trim panel in the cargo area When this lock is pressed all doors and the liftgate will lock POWER SIDE VIEW MIRRORS To change mirror position first select a ae QD mirror by moving the selector control left lt Q or right P gt then moving the control to set the desired position Power heated side view mirrors if equipped The heated mirrors will melt frost thin ice or remove fog when the rear window defroster is activated 31 Controls and features CHILDPROOF DOOR LOCKS When these locks are set the rear doors cannot be opened from the inside The rear doors can be opened from the outside when the doors are unlocked Move lock control up
9. set speed To return to a set speed e Press RESUME For RESUME to operate the vehicle speed must be faster than 48 km h 30 mph 25 Controls and features Indicator light Lights when the cruise CRUISE control is turned on and remains lit until either the cruise control or the ignition is turned off TURN SIGNAL CONTROL Turn signals Push the control down to activate the left turn signal Push control up to activate the right turn signal High beams Push the control forward to activate the high beams 26 Controls and features Flash to pass Pull the control toward you to activate the flash to pass function WINDSHIELD WIPERS AND WASHER Push the control on the end of the turn signal control to activate washer Push the control once for a single wipe Push and hold for a longer wash cycle Turn the dial at end of the turn signal control to adjust wiper interval and speed HAZARD FLASHER Push the control located on top of the steering column to activate four way flashers Push control again to turn flashers off 27 Controls and features TILT STEERING Pull the tilt steering control toward you to move the steering wheel up or down Hold the control while adjusting the wheel to the desired position then release the control A Never adjust the steering wheel when the vehicle is moving MOON ROOF IF EQUIPPED Press SLIDE to open and c
10. should always wear safety belts Follow all the important safety restraint and air bag precautions that apply to adult passengers in your vehicle If the shoulder belt portion of a combination lap and shoulder belt can be positioned so it does not cross or rest in front of the child s face or neck the child should wear the lap and shoulder belt Moving the child closer to the center of the vehicle may help provide a good shoulder belt fit If the shoulder belt cannot be properly positioned 67 Seating and safety restraints e move the child to one of the seats with a lap belt only if equipped OR e if the child is the proper size restrain the child in a Safety seat Do not leave children unreliable adults or pets unattended in your vehicle To improve the fit of lap and shoulder belts on children who have outgrown child safety seats Ford recommends use of a belt positioning booster seat that is labelled as conforming to all Federal motor vehicle safety standards Belt positioning booster seats raise the child and provide a shorter firmer seating cushion that encourages safer seating posture and better fit of lap and shoulder belts on the child A belt positioning booster should be used if the shoulder belt rests in front of the child s face or neck or if the lap belt does not fit snugly on both thighs or if the thighs are too short to let the child sit all the way back on the seat cushion when the lower legs hang
11. so the heater can be plugged in the night before starting the vehicle A To prevent electrical shock do not use your heater with ungrounded electrical systems or two pronged cheater adapters 81 Starting Guarding against exhaust fumes Although odorless and colorless carbon monoxide is present in exhaust fumes Take precautions to avoid its dangerous effects AN If you ever smell exhaust fumes of any kind inside your vehicle have your dealer inspect and fix your vehicle immediately Do not drive if you smell exhaust fumes These fumes are harmful and could kill you Have the exhaust and body ventilation systems checked whenever e the vehicle is raised for service e the sound of the exhaust system changes e the vehicle has been damaged in a collision Important ventilating information If the engine is idling while the vehicle is a stopped in an open area for long periods of time open the windows at least 2 5 cm one inch Adjust the heating or air conditioning if equipped to bring in fresh air 82 Improve vehicle ventilation by keeping all air inlet vents clear of snow leaves and other debris Starting 83 Driving BRAKES Your brakes are self adjusting Refer to the Service Guide for maintenance scheduling Anti lock brake system ABS if equipped The ABS operates by detecting the onset mo of wheel lock up aL during brake i applications and compensating for this t
12. MERCON transaxle MERCON ATF Engine oil XO 5W30 Motorcraft WSS Gasoline QSP 5W30 super M2C153 F engines premium and API Certification Mark Constant E 43Z 195904 CV joint ESP velocity A grease M1C207 A joints high temp Engine E2F Z Ford ESE coolant 19549 AA premium M97B44 A cooling system fluid Power XT 2 QDX Motorcraft MERCON steering MERCON pump ATF reservoir ENGINE DATA Engine data Engine 3 0L SOHC 3 0L DOHC 3 4L DOHC V6 V6 V8 inches Horsepower 145 5250 200 5750 235 6100 rpm rpm rpm 161 Capacities and specifications Engine data rom rom rom 3 7 8 Spark plug 1 07 1 17 mm 0 042 0 046 inch system Valve 0 0 Check and clearance aintenance Maintenance adjust as cold _ inlet free necessary exhaust 100 000 miles VEHICLE DIMENSIONS dimensions mm in length width 3 O i i verall 1399 5 55 1 height 4 Wheelbase 2755 9 108 5 2755 9 108 5 5 Track 1564 6 61 6 1564 6 61 6 Front 162 Capacities and specifications Vehicle Sedan Wagon dimensions mm in 5 Track 1559 6 61 4 1569 7 61 8 Rear 163 Capacities and specifications 164 Capacities and specifications Z LS 9g OA e 1 165 Capacities and specifications IDENTIFYING YOUR VEHICLE Vehicle identification plate identificati
13. are available through Ford or Mercury Lincoln dealers Do not tow a trailer until your vehicle has been driven at least 800 km 500 miles If towing with a station wagon inflate the rear tires to 35 psi Towing a trailer places an additional load on your vehicle s engine transaxle brakes tires and suspension Inspect these components carefully after towing The amount of weight that you can tyow depends on the type of engine in your vehicle See the following charts 3 0L 2 Valve Vulcan Engine Passenger Luggage Max Trailer Load kg Load kg Wt kg Ibs Ibs Ibs Sedan 5 340 750 0 365 800 4 270 600 70 150 365 800 2 135 300 70 150 __ 500 1100 pS 2735 300 jo 565 1250 94 Driving 3 0L 2 Valve Vulcan Engine Station 4 270 600 365 800 Wagon 2 735 300 70 150 430 950 2 135 300 jo 500 1100 The above chart is based on the specified vehicle at a maximum GCW Vehicle weight Trailer weight equal to 2245 kg 4950 Ibs 3 0L 4 Valve Duratec Engine and SHO Sedan Passenger Luggage Max Trailer Load kg Load kg Wt kg Ibs Ibs Ibs Sedan 5 340 750 0 590 1300 95 2 135 300 0 795 1750 Station 5 340 750 70 150 455 1000 Wagon 2 135 300 70 150 660 1450 2 135 300 0 725 1600 The above chart is based on the specified vehicle at a maximum GCW Vehicle weight Trailer weight equal to 2270
14. at least one minute 3 The relearning process will automatically complete as you drive the vehicle e If you do not allow the engine to relearn its idle the idle quality of your vehicle may be adversely affected until the idle is eventually relearned e If the battery has been disconnected or a new battery has been installed the clock and the preset radio stations must be reset once the battery is reconnected 133 Maintenance and care e Always dispose of automotive batteries in a responsible manner Follow your communities standards for disposal Call your local recycling center to find out more about recycling automotive batteries CHANGING YOUR AIR FILTER To replace your air filter unclip the two latches separate the housing and remove the old filter Wipe the interior clean before inserting new air filter Lock the two latches Do not use oil impregnated air filters Filters other than the ones specified in this owner guide can cause serious damage Your warranties may not apply if your vehicle is damaged because you use the wrong air filter Refer to Motorcraft part numbers in the Capacities and specifications chapter CHECKING AND CHANGING WIPER BLADES Check the wiper blades at least twice a year or when they seem less effective than usual Substances such as tree sap and some hot wax treatments used by commercial car washes reduce the effectiveness of wiper blades Checking the wiper blades If th
15. button at the same time to switch between Fahrenheit and Celsius If the battery is disconnected the display will revert to Fahrenheit 2 fan speed Once AUTO is pressed fan speed is adjusted automatically for existing conditions You can override automatic fan speed at any time by pressing FAN The display window will show FAN and a series of dots indicating fan speed To return to automatic fan control press AUTO Manual override controls The override controls are located on the bottom of the EATC and allow you to determine where airflow is directed To return to full automatic control press AUTO e MAX A C Uses recirculated air to cool the vehicle The temperature will display 16 C 19 Controls and features 60 F To exit press AUTO or any of the other override controls MAX A C is noisier but more economical than A C The airflow will be from the instrument panel registers The air conditioning compressor will operate in this mode VENT Distributes outside air through the instrument panel registers However the air will not be cooled below the outside temperature lt A Panel and floor Distributes outside air through the instrument panel registers and the front and rear seat floor ducts The air will be heated or cooled based on temperature selection The air conditioning compressor will operate in this mode s Floor Allows for maximum heating through
16. damage may not be covered by your warranty Your vehicle was not designed to use fuel containing manganese based additives such as MMT Additionally vehicles certified to California emission standards indicated on the underhood Vehicle Emissions Control Information label are designed to operate on California reformulated gasolines If California reformulated gasoline is not available when you refuel your vehicle can be operated on non California fuels However even though your engine will perform adequately on other gasolines the performance of the emission control devices and systems may be adversely affected Repair of damage caused by using a fuel that your vehicle was not designed for may not be covered by your warranty Octane recommendations Your vehicle is designed to use regular w gasoline with an 87 R M 2 octane rating of 87 We do not recommend gasolines labeled as regular in high altitude areas that are sold with octane ratings of 86 or even less Do not be concerned if your vehicle sometimes knocks lightly However if it knocks heavily under most driving conditions on the recommended octane 140 Maintenance and care fuel see your dealer or a qualified service technician to prevent any engine damage SHO engines Your vehicle is designed to use a premium gasoline for optimum performance with an R M 2 octane rating of 91 or higher Gasolines with lower octane ratings can be u
17. downhill If your vehicle speed is faster than the set speed while driving on a downhill in Overdrive you may want to shift to the next lower gear to reduce your vehicle speed If your vehicle slows down more than 16 km h 10 mph below your set speed on an uphill your cruise control will disengage This is normal Pressing RESUME will re engage it Do not use your cruise control in heavy traffic or roads that are winding slippery or unpaved To set a higher set speed e Press and hold SET ACCEL Release the control when the desired vehicle speed is reached or e Press and release SET ACCEL Each press will increase the set speed by 1 6 km h 1 mph or e Accelerate with your accelerator pedal then press and release SET ACCEL 24 Controls and features You can accelerate with the accelerator pedal at any time during cruise control usage Releasing the accelerator pedal will return your vehicle to the previously programmed set speed To set a lower set speed e Press and hold COAST Release the control when the desired speed is reached or e Press and release COAST Each press will decrease the set speed by 1 6 km h 1 mph or e Depress the brake pedal When the desired vehicle speed is reached press SET ACCEL To disengage cruise control e Depress the brake pedal Disengaging the cruise control will not erase the previously programmed set speed Pressing OFF will erase the previously programmed
18. have the SRS serviced at your dealership or by a qualified technician immediately Unless serviced the system may not function properly in the event of a collision DISPOSAL OF AIR BAGS AND AIR BAG EQUIPPED VEHICLES For disposal of air bags or air bag equipped vehicles see your local dealership or qualified technician Air bags MUST BE disposed of by qualified personnel 66 Seating and safety restraints IMPORTANT CHILD RESTRAINT PRECAUTIONS You are required by law to use safety restraints for children in the U S and Canada If small children ride in your vehicle generally children who are four years old or younger and who weigh 18 kg 40 Ibs or less you must put them in safety seats made especially for children Check your local and state or provincial laws for specific requirements regarding the safety of children in your vehicle AN Never let a passenger hold a child on his or her lap while the vehicle is moving The passenger cannot protect the child from injury in a collision Always follow the instructions and warnings that come with any infant or child restraint you might use When possible place children in the rear seat of your vehicle Accident statistics suggest that children are safer when properly restrained in the rear seating positions than in the front seating position CHILDREN AND SAFETY BELTS Children who are too large for child safety seats as specified by your child safety seat manufacturer
19. humidity buildup inside the vehicle don t drive with the climate control system in the OFF position e Don t put objects under the front seat that will interfere with the air circulation to the back seats e Remove any snow ice or leaves from the air intake area at the bottom of the windshield under the hood on the passenger side of your vehicle e f the air conditioner works well in MAX A C but not in A C this may indicate that the passenger compartment air filter if equipped needs to be replaced Rear window defroster and heated outside rear view mirrors The defroster clears R DEF away fog frost and thin ice from the rear window and outside rear view mirrors Clear away snow from rear window and mirrors The defroster operates for 10 minutes then shuts off If more defrosting is required press the control again 21 Controls and features Liftgate wiper and washer wagon only The liftgate wiper washer control is located under a headlamp controls CONE Press the wiper control OOR to activate the rear wiper Press control again to turn off the wiper Press the washer control to activate rear washer The wiper will come on when the pressed if not already Ole washer control is on AUDIO SYSTEM Refer to the Audio Guide for instructions on how to operate the audio system FUEL PUMP SHUT OFF SWITCH Refer to the Roadside emergencies chapter for instructions on how to operate
20. kg 5450 Ibs Do not exceed the GVWR or the GAWR specified on the Safety Compliance Certification Label AN Towing trailers beyond the maximum recommended gross trailer weight exceeds the limit of the vehicle and could result in engine damage transaxle damage structural damage loss of control and personal injury 95 Driving Preparing to tow Use the proper equipment for towing a trailer and make sure it is properly attached to your vehicle See your dealer or a reliable trailer dealer if you require assistance Hitches Your vehicle has a load carrying hitch This type of hitch places the tongue load of a trailer on the rear wheels of your vehicle You must distribute the load in your trailer so that 10 15 of the total weight of the trailer is on the tongue Safety chains Always connect the trailer s safety chains to the vehicle To connect the trailer s safety chains cross the chains under the trailer tongue and allow slack for turning corners If your use a rental trailer follow the instructions that the rental agency gives to you Trailer brakes Electric brakes and manual automatic or surge type brakes are safe if installed properly and adjust them to the manufacturer s specifications The trailer brakes must meet local and Federal regulations A Do not connect a trailer s hydraulic brake system directly to your vehicle s brake system Your vehicle may not have enough braking power and yo
21. may not be appropriate for certain terrains If the transaxle shifts back and forth between third and fourth gears while you are driving hilly roads or if your vehicle requires additional power for climbing hills shift into D Drive or press the O D OFF switch if equipped 90 Driving If the O D OFF indicator light if equipped is flashing on and off when the vehicle is started or does not come on when the O D OFF switch is pressed it means there is a malfunction in your transaxle s electronic system Contact your dealer as soon as possible or damage to the transaxle may occur When to use D Drive or press the O D OFF switch if equipped D Drive eliminates the needless shifting back and forth between third and fourth gears that your vehicle may do when driving on hilly terrain It also gives more engine braking than overdrive to slow your vehicle on downgrades 2 Second if equipped Use 2 Second for start up on slippery roads or to give you more engine braking to slow your vehicle on downgrades 91 Driving 1 First fF ee for when added engine braking is desired when descending steep hills The automatic transaxle will shift to the proper gear to ascend any grade without any need to shift to 1 First Do not go faster than 61 km h 38 mph when in this gear You can upshift from 1 First to overdrive at any time AN When parking do not use the gearshift in pl
22. modify the Air Bag Supplemental Restraint System or its fuses See your Ford or Lincoln Mercury dealer CHILDREN AND AIR BAGS For additional important safety information read all information on safety restraints in this guide Children should always wear their safety belts Failure to follow these instructions may increase the risk of injury in a collision A Rear facing child seats or infant carriers should never be placed in the front seats HOW DOES THE AIR BAG SUPPLEMENTAL RESTRAINT SYSTEM WORK The SRS is designed to activate when the vehicle sustains sufficient longitudinal deceleration similar to hitting a fixed barrier head on at 12 24 km h 8 14 mph The fact that the air bags did not inflate in a collision does not mean that something is 64 Seating and safety restraints wrong with the system Rather it means the forces were not of the type sufficient to cause activation The air bags inflate and deflate rapidly upon activation After air bag deployment it is normal to notice a smoke like powdery residue or smell the burnt propellant This may consist of cornstarch talcum powder to lubricate the bag or sodium compounds e g baking soda that result from the combustion process that inflates the air bag Small amounts of sodium hydroxide may be present which may irritate the skin and eyes but none of the residue is toxic A Several air bag system components get
23. open Service engine soon This light illuminates SERVICE when the engine s SOON Emission Control System requires service It will also illuminate when the ignition key is in the ON position and the engine is off Low fuel If the fuel gauge reaches approximately 1 16th of a tank this Instrumentation lamp will illuminate The ignition must be turned on for this lamp to illuminate Low coolant if equipped This lamp will LOW illuminate when the COOLANT engine coolant inside the reservoir is low This lamp will come on when the ignition is first turned on but then should turn off If the lamp stays on and a chime sounds you should check the coolant level inside the reservoir For instructions on adding coolant see Engine coolant in the index Anti theft alarm light if equipped This light is used when THEFT you set the anti theft alarm system See Anti theft system in the index O D off if equipped IIluminates when the transaxle control O D switch TCS has been OFF pushed When the light is on the transaxle does not shift into overdrive If the light does not come on when the TCS is depressed or if the light flashes when you are driving have your vehicle serviced Anti lock brake system ABS if equipped Momentarily illuminates when the ignition is turned on and the engine is off If the light stays on or continues to flash the ABS needs to be serviced Instrumentation
24. power distribution box contains high current fuses that protect your vehicle s main electrical systems from overloads 105 Roadside emergencies The high current fuses are coded as follows Location Rating protected 2 30A Constant module 40A Ignition switch a a e i i relay Ignition switch 6 Boa Power seats 7 40A Rear window defrost relay 30A Thermactor air bypass solenoid EAM solid state relay a ie Constant control relay module ay Constant control relay module eee eee relay O carry control module C e e oclaa module 4 Notused 106 Roadside emergencies Location Rating protected 15 15A Daytime running lamps DRL module diagnostic monitor 20A Rear control unit CD changer module a a Horn relay powertrain control module 15A Headlamp switch autolamp park relay 21 Not used O 22 30A Autolamps relay multi function switch headlamp switch 230A 24 NA 25 NA 26 30A Generator Voltage regulator C 1 107 Roadside emergencies Fuse Relay Fuse Amp Circuits Location Rating protected Heated oxygen sensors eo vent Maxi fuses Mini fuses A Always disconnect the battery before servicing high current fuses A Always replace the cover to the Power Distribution Box before reconnecting the battery or refilling fluid reservoirs Relays Relays are located in the power distribution box and should be replaced by qualifie
25. raised off the ground 4 Put the jack in the jack notch next to the door of the tire you are changing Turn the jack handle clockwise until the wheel is completely off the ground 5 Remove the lug nuts with the lug wrench 6 Replace the flat tire with the spare tire making sure the valve stem is facing outward Reinstall lug nuts until the wheel is snug against the hub Do not fully tighten the lug nuts until the wheel has been lowered 7 Lower the wheel by turning the jack handle counterclockwise 8 Remove the jack and fully tighten the lug nuts in the order shown 111 Roadside emergencies 9 Put flat tire jack and lug wrench away Make sure jack is fastened so it does not rattle when you drive Unblock the wheels Removing and replacing wheel covers Full wheel cover Your vehicle may have wheel covers with a wire retention system To remove the wheel cover pry it loose by inserting the tapered end of the jack handle between the wheel cover and wheel To replace the wheel cover 1 One of the windows on the wheel cover is identified with a valve stem logo on the back side of the wheel cover Install the wheel over the wheel with the window at the valve stem 2 Hold the wheel cover in this position and press the cover onto the wheel with the palm of your hand Do not force or hammer the cover Center wheel cover 1 Pry the center ornament off the wheel cover with the lug
26. retractors then reinsert both belt tongues Removing your child from the built in child seat 1 Squeeze the tabs on the top and the bottom of the chest clip and pull the halves apart to open the chest clip 2 Press the release button on the crotch safety belt buckle 3 Slide the shoulder belts off the child s shoulders and remove the child 76 Seating and safety restraints To stow the built in child seat Return the child seat cushion to the upright position then press firmly in the center and top of the child seat Inspecting the built in child seat after a collision All built in child restraints including seats buckles retractors seat latches Interlocks and attaching hardware should be inspected by a qualified technician after any collision If the child seat was in use during a collision Ford recommends replacing it Built in child restraints not in use during a collision should be inspected and replaced if either damage or improper operation is noted 77 Starting PREPARING TO START THE VEHICLE Engine starting is controlled by the spark ignition system This system meets all Canadian Interference Causing Equipment standard requirements regulating the impulse electrical field strength of radio noise When starting a fuel injected engine avoid pressing the accelerator before or during starting Only use the accelerator when you have difficulty st
27. routine cleaning wipe the surface with a soft damp cloth For more thorough cleaning wipe the surface with a leather and vinyl cleaner or a mild soap Cleaning and maintaining the safety belts Clean the safety belts with a mild soap solution recommended for cleaning upholstery or carpets Do not bleach or dye the belts because these actions may weaken the belt webbing Check the safety belt system periodically to make sure there are no nicks wear or cuts If your vehicle has been involved in an accident have all the safety restraints examined by a qualified technician Cleaning the built in child seat if equipped Clean the built in child seat with mild soap and water Do not use household cleaning products because they may weaken the safety belt webbing or damage the vinyl parts of the seat The child seat liner is removable and may be machine washed and air dried 155 Capacities and specifications MOTORCRAFT PART NUMBERS 3 0L Vulcan engine Component Air filter A 1630 F Fuel filter F G 800 A Battery standard Battery optional Fuel filter F G 800 Passenger FP 6 compartment air filter if equipped EV Oil filter PCV valve Spark plug Refer to Vehicle Emissions Control Information VECI decal for spark plug and gap information If a spark plug is removed for inspection it must be reinstalled in the same cylinder Cylinders No 1 2 and 3 have a PG suffix Cylinders No 4 5 and 6 ha
28. running and set the parking brake Wipe off the dipstick Co EET cap and pull the dipstick out Wipe the dipstick clean put the dipstick back in the filler tube completely then pull it back out and read the fluid level The fluid should be in the crosshatched area not necessarily at the top of the crosshatched area Your vehicle should not be driven until some fluid has been added if the fluid level is below the bottom hole on the dipstick and the outside temperature is below 10 C 50 F Add only enough fluid to bring the level above the bottom hole 131 Maintenance and care Adding transaxle fluid Before adding any fluid be sure the correct type is being used this is indicated on the transaxle dipstick Add fluid in 250 ML 1 2 pint increments through the filler tube to bring the level within the crosshatched area If the level is above the top hole on the dipstick a qualified technician should remove the excess fluid Always dispose of automotive fluids in a responsible manner Follow your community s standards for disposing of these types of fluids Call your local recycling center to find out about recycling automotive fluids BATTERY If the original equipment maintenance free battery needs replacing it may be replaced with a low maintenance battery For more information on replacement batteries refer to Motorcraft part numbers in the Capacities and specifications chapter
29. such non Ford parts should be equivalent to genuine F ord Motor Company parts in performance and durability It is the owner s responsibility to determine the equivalency of such parts Please consult your Warranty Information Booklet for complete warranty information AN Do not park idle or drive your vehicle in dry grass or other dry ground cover The emission system heats up the engine compartment and exhaust system which can start a fire Watch for fluid leaks strange odors smoke loss of oil pressure the charging system warning light the service engine soon light or the temperature warning light These sometimes indicate that the emissions system is not working properly Do not make any unauthorized changes to your vehicle or engine Changes that cause more unburned fuel to reach the exhaust system can increase the temperature of the engine or exhaust system By law anyone who manufactures repairs services sells leases trades vehicles or supervises a fleet of vehicles is not permitted to intentionally remove an emission control device or prevent it from working In some of the United States and Canada vehicle owners may be liable if their emission control device is removed or prevented from working 143 Maintenance and care Never use a metal exhaust collector when you service your vehicle If the metal collector contacts any of your vehicle s plastic trim or bumper parts they could melt or deform Do not d
30. system heats up the engine compartment and exhaust system which can start a fire A Do not start your vehicle in a closed garage or in other enclosed areas Exhaust fumes can be toxic Always open the garage door before you start the engine See Guarding against exhaust fumes in this chapter for more instructions A If you smell exhaust fumes inside your vehicle have your dealer inspect your vehicle immediately Do not drive if you smell exhaust fumes 80 Starting STARTING THE ENGINE 1 Turn the key to 5 Start without pressing the accelerator The key will return to 4 On 2 If the engine does not start within five seconds wait ten seconds and try again 3 If the engine does not start in two attempts OR the temperature is below 12 C 10 F depress accelerator and start the engine while holding the accelerator down Release accelerator when engine starts 4 After idling for a few seconds apply the brake and release the parking brake Using the engine block heater if equipped An engine block heater warms the engine coolant which improves starting warms up the engine faster and allows the heater defroster system to respond quickly They are strongly recommended if you live in a region where temperatures reach 23 C 10 F or below For best results plug the heater in at least three hours before starting the vehicle Using the heater for longer than three hours will not harm the engine
31. the brake pedal is released The doors may not lock automatically if the driver e shifts through gears without pressing the brake e shifts through gears quickly after starting the vehicle e releases their foot from the brake while someone has stepped out of the vehicle for a moment Deactivating the system by using the controls for the keyless entry system 1 Enter your permanent five digit entry code not the user code you may have set 2 Within five seconds press and hold 7 8 42 Seating and safety restraints 3 Within five more seconds press and release 3 4 4 Release 7 8 To reactivate the system repeat the system deactivating instructions You can also deactivate or reactivate the autolock feature by this method 1 Make sure the anti theft system is not armed or triggered ignition is off and all doors are closed 2 Turn the ignition key from OFF to ON 3 Press the door power unlock switch three times 4 Turn the ignition key from ON to OFF 5 Press the door power unlock switch three times 6 Turn the ignition key back to ON within 30 seconds of step two 7 The horn should chirp once If not wait 30 seconds and repeat steps one through six 8 Press the door power unlock switch 9 Press the door power lock switch 10 The horn will chirp once if the autolock feature was deactivated twice one short chirp followed by along chirp if the autolock feature was activated 11 Turn th
32. the front and rear seat floor ducts Floor and defrost Distributes outside air through the floor ducts and the windshield defroster ducts If the outside temperature is about 10 C 50 F or higher the air conditioner will dehumidify the air to prevent fogging The air conditioning compressor will operate in this mode CHN F DEF Defrost Distributes outside air through the windshield defroster ducts It can be used to clear ice or fog from the windshield If the outside temperature is about 10 C 50 F or higher the air conditioner will dehumidify the air to prevent fogging The air conditioning compressor will operate in this mode OFF Outside air is shut out and the fan will not operate Displaying outside temperature OUTSIDE TEMP Outside air temperature will be displayed If the EATC is off the display will go blank after four seconds If the EATC is on the display will show the outside temperature until the button is pressed again 20 Controls and features The outside temperature reading is most accurate when the vehicle is moving Higher readings may be obtained when the vehicle is not moving The readings that you get may not agree with temperatures given on the radio due to differences in vehicle and station locations Operating tips e In humid weather select Y F DEF before driving This will prevent your windshield from fogging After a few minutes select any desired position e To prevent
33. the fuel pump shut off switch POSITIONS OF THE IGNITION 1 ACCESSORY allows the electrical accessories such as the radio and wipers washer to operate while the engine is not running 2 LOCK locks the steering wheel and gearshift lever and allows key removal 22 Controls and features 3 OFF shuts off the ignition and accessories and allows the gearshift and steering wheel to move 4 ON tests the warning lights The key must remain here when the engine is running 5 START cranks the engine The key must return to ON when running CRUISE CONTROL To turn cruise control on Press ON Vehicle speed cannot be controlled until the vehicle is travelling at or above 48 km h 30 mph Do not use the cruise control in heavy traffic or winding slippery or unpaved roads Do not shift into N Neutral while the cruise control is on To turn cruise control off Press OFF or turn off the vehicle ignition Once cruise control is switched off the previously programmed set speed will be erased 23 Controls and features To set a speed Press SET ACCEL For cruise control to operate the cruise control must be ON and the vehicle speed must be greater than 48 km h 30 mph If you drive up or down a steep hill your vehicle speed may vary momentarily slower or faster than the set speed This is normal Cruise control cannot reduce the vehicle speed if it increases above the set speed on a
34. your nearest Ford or Lincoln Mercury dealer who has access to the master set of keys Do not use an impact wrench with the anti theft key JUMP STARTING YOUR VEHICLE AN The gases around the battery can explode if exposed to flames sparks or lit cigarettes An explosion could result in injury or vehicle damage A Do not push start your vehicle You could damage the catalytic converter For further information see J umper Cables in the Index Batteries contain sulfuric acid which burns skin eyes and clothing CONNECTING THE JUMPER CABLES 1 Position the vehicles so that they do not touch one another 2 Switch off the engine Switch off any unnecessary electrical equipment 114 Roadside emergencies 3 Connect the positive terminal of the 4 discharged battery 1 i to the positive We terminal of the booster battery 2 4 Connect one end of the second lead to the Cf negative terminal of the booster battery 3 and the other end to a metal part of the engine to be started 4 not to the negative terminal of the discharged battery 5 Make sure that the jump leads are clear of moving parts of the engine AN Do not connect the end of the second cable to the negative terminal of the battery to be jumped A spark may cause an explosion of the gases that surround the battery JUMP STARTING 1 Start the booster vehicle and run the engine at moderately increased sp
35. 4L SHO engine 4 Check the fluid level in the reservoir It should be between the MIN and MAX lines Do not add fluid if the level is within this range 5 If the fluid is low add fluid in small amounts continuously checking the level until it reaches the range between the MIN and MAX lines Be sure to put the cap back on the reservoir AUTOMATIC TRANSAXLE FLUID Under normal circumstances the transaxle fluid does not need to be checked Refer to the Service Guide for fluid replacement intervals If the transaxle is not working properly for instance the transaxle may slip or shift slowly or even some fluid leakage red fluid under the vehicle the fluid should be checked 130 Maintenance and care Checking the automatic transaxle fluid Your vehicle should be at normal operating temperature to get an accurate reading on the transaxle fluid dipstick Normal operating temperature is reached after driving approximately 32 km 20 miles If the vehicle has been operating for extended periods of time at high speeds driven in city traffic during hot weather or has been pulling a trailer the vehicle should be turned off for at least 30 minutes to allow the fluid to cool before checking With the vehicle on a level surface and the brake pedal firmly applied move the gearshift through all the gears Allow sufficient time for each position to engage Securely latch the gearshift in P Park leave the engine t
36. Before driving Introduction Instrumentation Controls and features Seating and safety restraints Starting and driving Starting Driving Roadside emergencies Servicing Maintenance and care Capacities and specifications Reporting safety defects Index Contents 14 35 78 84 99 118 156 168 169 Introduction ICONS Indicates a warning Read the following section on Warnings for a full explanation of them Indicates that vehicle information related to recycling and other environmental concerns will follow We must all play our part in protecting the environment Correct vehicle usage and the authorized disposal of waste cleaning and lubrication materials are significant steps towards this aim WARNINGS How can you reduce the risk of personal injury and prevent possible damage to others your vehicle and its equipment In this owner s guide answers to such questions are contained in comments highlighted by the warning triangle symbol BREAKING IN YOUR VEHICLE There are no particular breaking in rules for your vehicle Simply avoid driving too briskly during the first 1 600 km 1 000 miles of driving Vary speeds frequently This is necessary to give the moving parts a chance to break in If possible you should avoid full use of the brakes for the first 1 600 km 1 000 miles From 1 600 km 1 000 miles onwards you can gradually increase the performance of your vehicle up to the pe
37. N or START If successful the anti theft indicator will illuminate for two seconds Repeat procedure for all new keys If key coding fails the N11 7 anti theft indicator will THEFT flash ZIIN 49 Seating and safety restraints Coding failure can be caused by any of the following e The new key was not inserted into the ignition within 15 seconds e 16 keys have already been programmed e The new key does not have an electronic code 50 Seating and safety restraints SEATING Head restraints The head restraints can be moved up and down gt Front seats Adjusting the manual seats Lift bar to move seat forward or backward gt x Pull lever up to adjust seatback A Never adjust the driver s seat or seatback when the vehicle is moving Seating and safety restraints Adjusting the power seats if equipped Press to move front or rear of seat up and down lt bs Press in the direction to raise or lower the seat or to move the seat forward or backward Push to increase or decrease lumbar support Pull lever up to adjust seatback A Never adjust the driver s seat or seatback when the vehicle is moving 52 Seating and safety restraints 2nd seat Split folding rear seat One or both rear seatbacks can be folded down to provide additional cargo space To lower the seatback s from inside the vehicle lift seatback release handle pull tab then fold seat
38. TS Built in child safety seat wagon if equipped The second row bench seat may include a built in child seat This child seat conforms to all F ederal and local motor vehicle safety standards Read the labels located on the child seat cushion and shoulder belt for information on the built in child seat Use the built in child seat only if the child is at least one year old weighs 10 27 kg 22 60 Ibs and the child s shoulders fit below the shoulder harness slots on the built in child seat Children not meeting these requirements should be secured in an approved aftermarket seat Refer to Children and infant or child safety seats in this chapter Built in child seat retractors The belts on built in child seats are equipped with a retractor that locks when both tongues are latched into the crotch safety belt buckle The retractor will automatically snug the belts around the child If the belts do not remain snug take the vehicle to the dealer for child seat repair The belts will not snug during a collision Placing your child in the built in child seat A Failure to follow all of the instructions on the use of this child restraint system can result in your child striking the vehicle s interior during a sudden stop or crash AN Never use the Built In Child Seat as a booster cushion with the adult safety belts A child using the adult belts could slide forward and out from under the safety belts 74 Seating and safet
39. a two person operation 38 Seating and safety restraints 1 Remove the shade from the mounting brackets by detaching the safety clip and pressure fit plastic knobs from either side of the shade 2 Wrap the vinyl around the tube twice by twisting the tube away from you Tuck the edged of the vinyl end cap with each wrap 3 Fold the vinyl toward the center making sure the edges clear the end cap slots Use tape or a rubber band to hold the vinyl on the left side of the tube 4 Push in the right end cap marked R about 6 mm 1 4 inch to disengage the clutch and hold in while turning the tube toward you fourteen times 5 Let go of the right end cap and unfold the vinyl Place the vinyl into the end cap slots 6 Place the shade back into the vehicle A The cover may cause injury in a sudden stop or accident if it is not securely installed LUGGAGE RACK WAGON ONLY The rear crossbar can be adjusted to fit the item being carried The front crossbar does not move No more than 44 kg 100 Ibs can be loaded on the luggage rack To adjust the luggage rack loosen the adjusting levers by pushing them toward the front of the vehicle then slide the crossbar forward and lock the adjusting levers by pulling them toward the back of the vehicle 39 Seating and safety restraints KEYLESS ENTRY SYSTEM IF EQUIPPED You can lock or unlock the vehicle doors without using a key we See also Remot
40. a vinyl cleaner for routine cleaning of plastic Clean with a tar remover if necessary Do not clean plastic parts with thinners solvents or petroleum based cleaners Cleaning the exterior lamps Wash the exterior lamps with the same detergent you used to wash the exterior of your vehicle Use glass cleaner or tar remover if necessary To avoid scratching the lamps do not use a dry paper towel chemical solvents or abrasive cleaners to clean the lamps AN lt Q aa ee 153 Maintenance and care Cleaning the wiper blades If the wiper blades do not wipe properly clean both the windshield and wiper blades using undiluted windshield wiper solution or a mild detergent Rinse thoroughly with clean water To avoid damaging the blades do not use fuel kerosene paint thinner or other solvents Cleaning the instrument panel x Clean instrument panel with a damp cloth then dry with a dry cloth Any cleaner or polish that increases the gloss of the upper portion of the instrument panel should be avoided The dull finish in this area is to help protect the driver from undesirable windshield reflection Cleaning the interior fabric Remove dust and loose dirt with a whisk broom or a vacuum cleaner Remove fresh spots immediately Follow the directions that come with the cleaner 154 Maintenance and care Cleaning leather seats if equipped For
41. ace of the parking brake Always set the parking brake fully and make sure that the gearshift is securely latched in Park P Turn off the ignition whenever you leave your vehicle Never leave your vehicle unattended while it is running If you do not take these precautions your vehicle may move unexpectedly and injure someone VEHICLE LOADING Before loading a vehicle familiarize yourself with the following terms e Base Curb Weight Weight of the vehicle including any standard equipment fluids lubricants etc It does not include passengers or aftermarket equipment e Payload Combined maximum allowable weight of cargo passengers and optional equipment The payload equals the gross vehicle weight rating minus base curb weight 92 Driving GVW Gross Vehicle Weight Base curb weight plus payload and weight The GVW is not a limit or a specification GVWR Gross Vehicle Weight Rating Maximum total weight of the base vehicle passengers optional equipment and cargo The GVWR is specific to each vehicle and is listed on oT Safety Compliance Label on the driver s door pillar GAWR Gross Axle Weight Rating Carrying capacity for each axle system The GAWR is specific to each vehicle and is listed on the Safety Compliance Label on the driver s door pillar GCWR Gross Combined Weight Rating Maximum combined weight of towing vehicle including passengers and cargo and the trailer The GCWR indicates the maximum lo
42. aded weight that the vehicle is allowed to tow Maximum Trailer Weight Rating Maximum weight of a trailer the vehicle is permitted to tow The maximum trailer weight rating equals the vehicle curb weight for each engine transaxle combination any required option weight for trailer towing and the weight of the driver from the GCWR for the towing vehicle Maximum Trailer Weight maximum weight of a trailer the loaded vehicle including passengers and cargo is permitted to tow It is determined by subtracting the weight of the loaded trailer towing vehicle from the GCWR for the towing vehicle Trailer Weight Range Specified weight range that the trailer must fall within that ranges from zero to the maximum trailer weight rating Remember to figure in the tongue load of your loaded trailer when figuring the total weight 93 Driving Do not exceed the GVWR or the GAWR specified on the Safety Compliance Certification Label Do not use replacement tires with lower weight capacities than the originals because they may lower the vehicle s GVWR and GAWR limitations Replacement tires with a higher weight limit than the originals do not increase the GVWR and GAWR limitations TRAILER TOWING Your vehicle is classified as a light duty towing the vehicle The amount of weight you can safely tow depends on the type of engine you have in your vehicle Your vehicle does not come from the factory fully equipped to tow No towing packages
43. al brakes fail the parking brake can be used to stop your vehicle in an emergency Since the parking brake applies only the rear brakes the vehicle s stopping distance will increase greatly and the handling of your vehicle will be adversely affected 85 Driving Pull release handle toward you to release parking brake Driving with the parking brake on will cause the brakes to wear out quickly and reduce fuel economy SEMI ACTIVE RIDE CONTROL TAURUS SHO ONLY Firm shock absorber performance enhances ride and handling during certain road conditions The shock absorber is returned to a softer performance when driver or road induced motion ceases This system is automatic and requires no driver input TRANSAXLE Brake shift interlock This vehicle is equipped with a brake shift interlock feature that prevents the gearshift from being moved from P Park unless the brake pedal is pressed If you cannot move the gearshift out of P Park with the brake pedal depressed 1 Apply the parking brake turn ignition key to LOCK then remove the key 2 Insert the key and turn it to OFF Apply the brake pedal and shift to N Neutral 3 Start the vehicle If it is necessary to use the above procedure to move the gearshift it is possible that a fuse has blown and the vehicle s brake lamps may not be operating properly Refer to Fuses and relays in the Roadside emergencies chapter 86 Driving A Do not drive your v
44. arting the engine For more information on starting the vehicle refer to Starting the vehicle in this chapter Before starting the vehicle 1 Make sure all vehicle occupants have buckled their safety belts For more information on safety belts and their proper usage refer to the Seating and safety restraints chapter 2 Make sure the headlamps and vehicle O o accessories are off e Make sure the parking brake is set e Make sure the gearshift is in P Park 7D 3 Turn the key to the ON position without turning the key to START 78 Starting Make sure the corresponding lights illuminate briefly If a light fails to illuminate have the vehicle serviced e If the driver s safety belt is fastened the A light does not illuminate Important safety precautions A computer system controls the engine s idle revolutions per minute RPM When the engine starts the idle RPM runs faster to warm the engine 79 Starting If the engine idle speed does not slow down automatically have the vehicle checked Do not allow the vehicle to idle for more than ten minutes AN Extended idling at high engine speeds can produce very high temperatures in the engine and exhaust system creating the risk of fire or other damage AN Do not park idle or drive your vehicle in dry grass or other dry ground cover The emission
45. back down In the sedan the seatbacks can also be folded down from inside the trunk Move the release lever on the back of the rear seatback to the OPEN oS MlM position and fold the seatback down When raising the seatback s make sure you hear the seat latch into place 3rd seat wagon only The third seat faces the rear of the vehicle For height and weight limits see the label on the seat cushion When the seat is down the back of your wagon has a flat surface for carrying cargo 53 Seating and safety restraints To open up the seat 1 Unlock the floor panel with the key then use the handle to fold the floor panel toward the front of the car 2 Remove the cargo cover The cargo cover must be removed or the seatback will not latch in the upright position 3 Lift the remote latch release on the left side of the compartment and fold the remaining floor panel until it latches Make sure the seatback is locked in the upright position To close the seat make sure the safety belts are in their correct notches then lift the remote latch release and push the seat down until it latches Pull up on the handle and push the floor panel into place 54 Seating and safety restraints SAFETY RESTRAINTS Safety restraints precautions AN Always drive and ride with your seatback upright and the lap belt snug and low across the hips AN To prevent the risk of injury make sure
46. cautions for your safety e Do not work on a hot engine AN The cooling fan is automatic and may come on at any time Always disconnect the negative terminal of the battery before working near the fan e If you must work with the engine running avoid wearing loose clothing or jewelry that could get caught in moving parts Take precautions with long hair e Do not work on a vehicle with the engine running in an enclosed space unless you are sure you have enough ventilation 118 Maintenance and care e Keep all lit cigarettes open flames and other lit material away from the battery and all fuel related parts If you disconnect the battery the engine must relearn its idle conditions before your vehicle will drive properly as explained in Battery in this chapter Working with the engine off 1 Set the parking brake fully and make sure the gearshift is securely latched is P Park 2 Turn off the engine and remove the key 3 Block the wheels fully to prevent the vehicle from moving ft RND21 unexpectedly Working with the engine on 1 Set the parking brake fully and make sure the gearshift is securely latched is P Park 2 Block the wheels fully to prevent the vehicle from moving unexpectedly 119 Maintenance and care Opening the hood 1 Inside the vehicle pull the hood release handle located under the bottom left corner of the instrument panel
47. conditions 1 This device may not cause harmful interference and 2 This device must accept any interference received including interference that may cause undesired operation Arming and disarming the alarm system Your remote entry system will e automatically arm the factory installed anti theft system when the doors are locked e reset the triggered anti theft alarm when the driver s door is unlocked or when PANIC is pressed on a programmed remote entry transmitter 45 Seating and safety restraints Replacing the batteries The transmitter is powered by two coin type three volt lithium batteries A decrease in operating range can be caused by e battery failure e weather conditions e structures around the vehicle To replace the batteries 1 Twist a thin coin between the two halves of the transmitter DO NOT TAKE THE FRONT PART OF THE TRANSMITTER APART 2 Place the positive side of new batteries down 3 Snap the two halves back together Replacing lost transmitters Take all your vehicle s transmitters to your dealer for programming if e atransmitter is lost or e you want to purchase additional transmitters up to four ILLUMINATED ENTRY SYSTEM The interior lamps illuminate when e the remote entry system is used to unlock the door or eo sound the personal T alarm The system automatically turns off after 25 seconds or when the ignition is turned to the START or ACC posit
48. d technicians 108 Roadside emergencies CHANGING THE TIRES Temporary spare tire information The temporary spare tire for your vehicle is labeled as such It is smaller than a regular tire and is designed for emergency use only AN If you use the temporary spare tire continuously or do not follow these precautions the tire could fail causing you to lose control of the vehicle possibly injuring yourself or others When driving with the temporary spare tire DO NOT e exceed 80 km h 50 mph under any circumstances e load the vehicle beyond maximum vehicle load rating listed on the Safety Compliance Label e tow a trailer e use tire chains e drive through an automatic car wash because of the vehicle s ground clearance e try to repair the temporary spare tire or remove it from its wheel e use the wheel for any other type of vehicle 109 Roadside emergencies Tire change procedure 1 Park on a level surface activate hazard flashers and set parking brake 2 Place gearshift lever in P Park block the diagonally opposite wheel then remove the spare tire jack and lug wrench In the sedan these are located in the trunk under the floor carpet In the wagon they are stored in the left side rear trim panel 110 Roadside emergencies 3 Loosen each wheel lug nut one half turn counterclockwise but do not remove them until the wheel is
49. down turn it counterclockwise and remove it Use Ford Premium Cooling System F luid E2FZ 19549 AA in Canada Motorcraft CXC 8 B or an equivalent premium engine coolant that meets Ford specification ESE M97B44 A Ford Premium Engine Coolant is an optimized formula that will protect all metals and rubber elastomers used in Ford cooling systems for four years or 80 000 km 50 000 miles Do not use alcohol or methanol antifreeze or any engine coolants mixed with alcohol or methanol antifreeze Do not use supplemental coolant additives in your vehicle These additives may harm your engine cooling system The use of an improper coolant may void your warranty of your vehicle s engine cooling system Recycled engine coolant Ford Motor Company recommends that Ford and Lincoln Mercury dealers use recycled engine coolant produced by Ford approved processes Not all coolant recycling processes produce coolant which meets Ford specification ESE M97B44 A and use of such coolant may harm engine and cooling system components Always dispose of used automotive fluids in a responsible manner Follow your community s regulations and standards for recycling and disposing of automotive fluids 128 Maintenance and care Coolant refill capacity To find out how much fluid your vehicle s cooling system can hold refer to Refill capacities in the Capacities and specifications chapter Have your dealer check the engine cooling system for
50. e Use cleaning fluid or alcohol with a clean cloth to remove Use tar remover to remove any tar spots Repairing paint chips Minor scratches or paint damage from road debris may be repaired with touch up paint paint repair foil or aerosol paint spray from the Ford accessory line Observe the application instructions on the products Remove particles such as bird droppings tree sap insect remains tar spots road salt and industrial fallout immediately Cleaning the wheels Wash the wheels with the same detergent you use to clean the body of your vehicle Do not use acid based wheel cleaners steel wool fuel or strong detergents Never use abrasives that will damage the finish of special wheel surfaces Use a tar remover to remove grease and tar Cleaning the engine Engines are more efficient when they are clean because grease and dirt buildup act as insulators and keep the engine warmer than normal Follow these guidelines to clean your engine 152 Maintenance and care e Take care when using a power washer to clean the engine The high pressure fluid could penetrate the sealed parts and cause damage e Do not spray with cold water to avoid cracking the engine block e Cover the highlighted areas to prevent water damage when cleaning the engine e Never wash or rinse the engine while it is running water in the running engine may cause internal damage Cleaning plastic exterior parts Use
51. e fuel economy Liters used x 100 Total kilometers traveled Total miles traveled Total gallons used Keep a record for at least one month This will provide an accurate estimate of the vehicle s fuel economy EMISSION CONTROL SYSTEM Your vehicle is equipped with catalytic converters which enable your vehicle to comply with applicable exhaust emission requirements A Exhaust leaks may result in the entry of harmful and potentially lethal fumes into the passenger compartment Under extreme conditions excessive exhaust temperatures could damage the fuel system the interior floor covering or other vehicle components possibly causing a fire To make sure that the catalytic converter and the other emission control parts continue to work properly e Use only unleaded fuel e Avoid running out of fuel e Do not turn off the ignition while your vehicle is moving especially at high speeds e Have the services listed in your Service Guide performed according to the specified schedule 142 Maintenance and care The Scheduled Maintenance Services listed in the Service Guide are required because they are considered essential to the life and performance of your vehicle and to its emissions system Ford strongly recommends the use of genuine Ford replacement parts If other than Ford or Motorcraft parts or Ford authorized parts are used for maintenance replacements or for the service of components affecting emission control
52. e lt A Panel and floor Distributes outside air through the instrument panel registers and the front and rear floor ducts The air conditioning compressor will operate in this mode e lt A Floor Allows for maximum heating The airflow is from the front and rear floor ducts e Floor and defrost Distributes outside air through the floor ducts and the windshield defroster ducts The air conditioning compressor will operate in this mode e HY Front defrost Distributes outside air through the windshield defroster ducts It can be used to clear ice or fog from the windshield The air conditioning compressor will operate in this mode Temperature control knob Turn the dial to the desired mix of warm red and cool blue air 16 Controls and features Operating tips e In humid weather select C before driving This will prevent your windshield from fogging After a few minutes select any desired position e To prevent humidity buildup inside the vehicle don t drive with the climate control system in the OFF position e Don t put objects under the front seat that will interfere with the airflow to the back seats e Remove any snow ice or leaves from the air intake area at the bottom of the windshield under the hood on the passenger side of your vehicle e f the air conditioner works well in MAX A C but not in A C this may indicate that the passenger compartment air filter if equipped needs t
53. e entry system if equipped in this chapter The computer code that operates the keyless system is located on your owner s wallet card found in the glove compartment Illuminated entry system e turns on the interior lights for approximately 25 seconds and e lights up the keypad controls for five seconds Do not push the control keypad with any hard object that could damage the controls Programming your own entry code This code does not replace the permanent code from the dealership To program your own code 1 Select five digits for your personal code 2 Enter the permanent code that the dealership gave you 3 Within five seconds press 1 2 4 Within five seconds of pressing 1 2 enter your personal code pressing each digit within five seconds of the previous digit You can now use either code The system remembers only one personal code at a time To erase your personal code 1 Enter the original permanent code 40 Seating and safety restraints 2 Press 1 2 within five seconds of step one 3 Wait six seconds For maximum security do not set a code that presents the numbers in sequential order or uses the same button five times Unlocking the doors with the keyless entry system The driver s door must be unlocked before any other If more than five seconds pass between pressing numbers enter the code again The system has shut down if the keypad light is out If the keyless entry s
54. e ignition key to OFF 12 The horn will chirp once to confirm you activated or deactivated the autolock feature 43 Seating and safety restraints REMOTE ENTRY SYSTEM IF EQUIPPED The remote entry system allows you to lock or unlock all vehicle doors without a key It also arms and disarms the anti theft system For more information on the anti theft system refer to Anti theft system in this chapter The remote entry features only operate with the ignition in the OFF position Unlocking the doors Press UNLOCK once to unlock the driver and illuminate the interior lamps Press UNLOCK a second time within five seconds to unlock all doors and liftgate wagon Using the trunk button Press once to open the trunk sedan or unlock the liftgate wagon 44 Seating and safety restraints Locking the doors Press LOCK to lock all doors and liftgate wagon To confirm all doors are closed and locked press LOCK a second time The doors will lock again the horn will chirp and the lamps will flash This process will arm your anti theft system For more information on arming the anti theft system refer to Anti theft system in this chapter Sounding the PANIC alarm Press PANIC to activate the alarm To deactivate the alarm press PANIC again or turn the ignition to ACC or ON This device complies with part 15 of the FCC rules Operation is subject to the following two
55. e wiper blades do not clean properly clean the windshield and wipers Use an undiluted windshield washer solution or a mild detergent then rinse thoroughly with clear water Do not use fuel kerosene paint thinner or other solvents to clean the wiper blades as these will damage the blades 134 Maintenance and care Changing the wiper blades When replacing wiper blades assemblies always use a Motorcraft part or equivalent To replace the blades follow the instructions on that come with the new wipers To make reaching the wipers easy turn the ignition to the ACC position then turn the wipers on When the wipers reach the vertical position turn the ignition OFF INFORMATION ABOUT TIRE QUALITY GRADES New vehicles are fitted with tires that have their Tire Quality Grade described Sees below molded into the SS tire s sidewall These Tire Quality Grades are determined by standards that the United States Department of Transportation has set Tire Quality Grades apply to new pneumatic tires for use on passenger cars They do not apply to deep tread winter type snow tires space saver or temporary use spare tires tires with nominal rim diameters of 10 to 12 inches or limited production tires as defined in Title 49 Code of F ederal Regulations Part 575 104 c 2 U S Department of Transportation Tire quality grades The U S Department of Transportation requires Ford to give you the following information about t
56. eed 2 Start the engine of the vehicle with the discharged battery 3 Once the engine has been started run both vehicles for a further three minutes before disconnecting the leads 115 Roadside emergencies REMOVING THE JUMPER CABLES 1 Remove the jumper cables in reverse order Take the cable off the metallic surface 1 first followed by the cable on the negative booster battery terminal 2 2 Remove the cable from the positive terminal of the booster battery 3 and then the discharged battery 4 3 After the disabled vehicle has been started allow it to idle for a while so the engine can relearn its idle conditions WRECKER TOWING If you need to have your vehicle towed contact a professional towing service or if you are a member your roadside assistance center Your Maino a z towed from the front _ fo lt unless conditions do SOLEO ESSI not allow it It is recommended that your vehicle be towed with a wheel lift or flatbed equipment When calling for a tow truck tell the operator what kind of vehicle you have A towing manual is available from Ford Motor Company for all authorized tow truck operators Have your tow truck driver refer to this manual for proper hook up and towing procedures for your vehicle 116 Roadside emergencies TOWING YOUR VEHICLE BEHIND ANOTHER
57. ehicle until you verify that the brakelamps are working If your vehicle gets stuck in mud or snow it may be rocked out by shifting from forward and reverse gears in a steady pattern Press lightly on the accelerator in each gear Do not rock the vehicle for more than a few minutes because it could damage the vehicle AN Always set the parking brake fully and make sure the gearshift is latched in P Park Turn off the ignition whenever you leave your vehicle Driving with an automatic overdrive transaxle column gearshift without O D off switch Your automatic overdrive transaxle provides fully automatic operation in either Overdrive or D Drive Driving with the shift selector in gives the best fuel economy for normal driving conditions For manual control start in 1 First and then shift manually To put your vehicle in gear start the engine depress the brake pedal then move gearshift out of P Park AN Hold the brake pedal down while you move the gearshift lever from position to position If you do not hold the brake pedal down your vehicle may move unexpectedly and injure someone 87 Driving Driving with an automatic overdrive transaxle column or console gearshift with O D off switch Your automatic overdrive transaxle provides fully automatic operation in either D Overdrive or with the O D OFF switch depressed Driving with the shift selector in D Overdrive gives the best fuel economy for
58. endency The front wheels are prevented from locking even when the brakes are firmly applied The accompanying illustration depicts the advantage of an ABS equipped vehicle on bottom to a non ABS equipped vehicle on top during hard braking ABS warning lamp The ABS warning lamp in the instrument cluster illuminates if an ABS fault is detected Have your vehicle serviced as soon as possible eon eal ses F effective unless the BRAKE BRAKE warning lamp is also illuminated Using ABS e In an emergency apply full force on the brake The ABS will be activated immediately thus allowing you to retain full steering control of your vehicle and providing there is sufficient space will enable you to avoid obstacles and bring the vehicle to a quiet stop 84 Driving e We recommend that you familiarize yourself with this braking technique However avoid taking any unnecessary risks Parking brake The parking brake should be used whenever the vehicle is parked Push pedal downward to set the parking brake The BRAKE warning lamp in the instrument C cluster illuminates and BRAKE remains illuminated when the ignition is turned ON until the parking brake is released AN Always set the parking brake fully and make sure the gearshift is latched in P Park Turn off the ignition whenever you leave your vehicle The parking brake is not designed to stop a moving vehicle However if the norm
59. engine coolant in this chapter Automotive fluids are not interchangeable do not use engine coolant antifreeze or windshield washer fluid outside of its specified function and vehicle location Adding engine coolant Do not put engine coolant in the container for the windshield washer fluid If sprayed on the windshield engine coolant could make it difficult to see through the windshield When the engine is cool add a 50 50 mixture of engine coolant and water to the reservoir to the engine coolant recovery reservoir DO NOT ADD DIRECTLY TO THE RADIATOR Add straight water only in an emergency but you should replace it with a 50 50 mixture of coolant and distilled water as soon as possible Check the coolant level in the coolant recovery reservoir the next few times you drive the vehicle If necessary add enough of a 50 50 mixture of coolant and water to bring the liquid level to the fill line on the reservoir A Never remove the coolant recovery cap while the engine is running or hot If you must remove the coolant recovery cap follow these steps to avoid personal injury 1 Before you remove the cap turn the engine off and let it cool 127 Maintenance and care 2 When the engine is cool wrap a thick cloth around the cap Slowly turn cap counterclockwise to the first stop 3 Step back while the pressure releases 4 When you are sure that all the pressure has been released use the cloth to press the cap
60. es front seat belt buckle assemblies slide bar if equipped shoulder belt height adjusters if equipped child safety seat tether bracket assemblies if equipped and attaching hardware should be inspected after a collision Ford recommends that all safety belt assemblies used in vehicles involved in a collision be 62 Seating and safety restraints replaced However if the collision was minor and a qualified technician finds that the belts do not show damage and continue to operate properly they do not need to be replaced Safety belt assemblies not in use during a collision should also be inspected and replaced if either damage or improper operation is noted Refer to Cleaning and maintaining the safety belts in the Maintenance and Care section IMPORTANT SUPPLEMENTAL RESTRAINT SYSTEM SRS PRECAUTIONS The supplemental restraint system is designed to e work with the safety belt to protect the driver and right front passenger e reduce certain upper body injuries Gees Failure to follow these instructions will affect the performance of the safety belts and increase the risk of personal injury N The right front passenger air bag is not designed to restrain occupants in the front seating position A Do not place objects or mount equipment on or near the air bag covers that may come into contact with an inflating air bag 63 Seating and safety restraints A Do not attempt to service repair or
61. es and specifications call al all al Name Type Engine oil Motocraft All 5 5 i motor oil i 5W30 super premium capacity oia Power Motorcraft Fill to line in steering MERCON reservoir fluid ATF Automatic Motorcraft All 12 7 13 4 transaxle MERCON AX4N ATF All 2 7 90 oz windshield washer concentrate Ultra clear Wagon 2 1 70 oz windshield washer concentrate 3 4L SHO engine Ford Part Vehicle Capacity Name Type Liters Quarts Brake High Fill to line fluid in EN in reservoir DOT 3 brake fluid Engine Premium All 10 0 10 6 coolant cooling system fluid 159 Capacities and specifications Ford Part Vehicle Capacity Quarts a oil Motocraft 6 1 6 5 motor sill 5W30 super premium Fuel a N A 60 6 16 0 capacity gallons Power Motorcraft All Fill to line in steering MERCON reservoir fluid ATF Automatic Motorcraft All 12 7 13 4 transaxle MERCON AX4N ATF All 2 7 90 oz windshield washer concentrate LUBRICANT SPECIFICATIONS Ford Part ord part Ford Name or Number Specification Equivalent Brake C6AZ master 19542 AB cylinder DOT brake fluid Door latch DOAZ Multi hood latch 19584 AA purpose auxiliary grease latch trunk and liftgate latches 160 Capacities and specifications bord Part Ford Part Ford Name or Number Specification Equivalent cylinders 19A501 B lubricant Automatic XT 2 QDX Motorcraft
62. fuel cap the pressure in the fuel tank can damage the fuel system or cause it to work improperly in a collision AN The fuel system may be under pressure If the fuel cap is venting vapor or if you hear a hissing sound wait until it stops before completely removing the cap Automotive fuels can cause serious injury or death if misused or mishandled Observe the following guidelines when handling automotive fuel e Extinguish all smoking materials and any open flames before fueling your vehicle e Always turn off the vehicle before fueling e Automotive fuels can be harmful or fatal if swallowed If fuel is swallowed call a physician immediately even if no symptoms are immediately apparent The toxic affects of fuel may not be visible for hours e Fuels can also be harmful if absorbed through the skin If fuel is splashed on the skin promptly remove contaminated clothing and wash skin thoroughly with soap and water e If fuel is splashed in the eyes remove contact lenses flush with water for 15 minutes and seek medical attention 139 Maintenance and care e Be particularly careful if you are taking Antabuse or other forms of disulfiram for the treatment of alcoholism Breathing gasoline vapors or skin contact could cause an adverse reaction Consult a physician immediately Choosing the right fuel Use only UNLEADED FUEL The use of leaded fuel is prohibited by law and could damage your vehicle The
63. ghtness during vehicle movement The automatic locking mode is not available on the driver belt When to use the automatic locking mode e When a tight lap shoulder fit is desired e Any time a child safety seat is installed in the vehicle Refer to Children and infant or Child safety seats later in this chapter 56 Seating and safety restraints How to use the automatic locking mode e Buckle the combination lap and shoulder belt e Grasp the shoulder portion and pull downward until the entire belt is extracted e Allow the belt to retract As the belt retracts you will hear a clicking sound This indicates the safety belt is now in the automatic locking mode How to cancel the automatic locking mode Disconnect the combination lap shoulder belt and allow it to retract completely to cancel the automatic locking mode and activate the vehicle sensitive emergency locking mode Safety belts for front outboard passenger and rear outboard seating positions except wagon rear facing position Your vehicle is equipped with a dual locking mode retractor on the shoulder belt portion of the combination lap shoulder safety belt at these positions 57 Seating and safety restraints Front safety belt height adjustment Your vehicle has safety belt height adjustments for the driver and front passenger Adjust the height of the shoulder belt so the belt rests across the middle of your shoulder To lower
64. hicle is not positioned on a level surface the slope will be included in the level indicator Therefore vertical headlamp adjustment should be performed only when beam direction appears to be incorrect or a level surface can not be verified The horizontal aim must be adjusted first You will need one 7 mm box wrench or open end wrench The following procedure assumes that the vehicle s front structure is properly aligned If the vehicle has 149 Maintenance and care been in an accident requiring the front end of the vehicle to be repaired the horizontal indicator should be recalibrated by the service facility Horizontal aim adjustment 1 With the hood open locate the horizontal indicator and adjusting screw 2 Use a 7 mm wrench to turn the horizontal adjusting screw until the reference mark on the reflector extension aligns with the 0 reference mark on the horizontal indicator when viewed directly from above 3 When the horizontal aim has been adjusted close the headlamp access panel Adjusting the vertical aim The numbers shown on the vial indicate beam direction in degrees up or down 1 Do not adjust the vertical aim until after adjusting the horizontal aim 150 Maintenance and care 2 With the hood open locate the bubble level vertical aim indicator It is visible when viewed from the above rear of the headlamp
65. hot after inflation Do not touch them after inflation AN If the air bag is inflated the air bag will not function again and must be replaced immediately If the air bag is not replaced the URE area will increase the risk of injury in a collision The SRS consists of e driver and passenger air bag modules which include the inflators and air bags e one or more impact and safing sensors e a readiness light and tone 65 Seating and safety restraints e and the electrical wiring which connects the components The diagnostic module monitors its own internal circuits and the supplemental air bag electrical system readiness including the impact sensors the system wiring the air bag system readiness light the air bag back up power and the air bag ignitors DETERMINING IF THE SYSTEM IS OPERATIONAL The SRS uses a readiness light in the instrument cluster or a tone to indicate the condition of the system Refer to the Air bag readiness section in the Instrumentation chapter Routine maintenance of the air bag is not required A difficulty with the system is indicated by one or more of the following e The readiness light will either flash or Y stay lit e The readiness light will not illuminate immediately after ignition is turned on e A group of five beeps will be heard The tone pattern will repeat periodically until the problem and light are repaired If any of these things happen even intermittently
66. ion The inside lights will not turn off if e they have been turned on with the dimmer control or 46 Seating and safety restraints e any door is open PERIMETER ANTI THEFT SYSTEM IF EQUIPPED TAIWAN AND RUSSIA ONLY When armed this system will protect your vehicle from unauthorized entry When unauthorized entry occurs the system will flash the headlamps parking lamps and the theft indicator lamp and will chirp the horn Arming the system The system is ready to arm whenever the ignition is turned off Any of the following actions will prearm the alarm system e Pressing LOCK on the remote transmitter doors opened or closed e Pressing 7 8 and 9 0 on the keyless entry pad at the same time to lock the doors doors opened or closed e Opening a door and pressing the power door lock button to lock the doors e Using the door key to lock the doors doors opened or closed If a door or the liftgate THEFT wagon is open the system is prearmed and is waiting for the door to close or liftgate to close The THEFT indicator in the instrument cluster will be lit continuously when the system is prearmed 47 Seating and safety restraints Once the doors and NTL 7 liftgate wagon are THEFT closed the system will ZUIN arm in 30 seconds When the system is armed the THEFT indicator will flash When you press the LOCK button twice within 5 seconds on your remote entry transmitter the h
67. ire grades exactly as the government has written it Treadwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course For example a tire grade 150 would wear one and one half 1 1 2 times as well on the government course as a tire grade 100 The relative 135 Maintenance and care performance of tires depends upon the actual conditions of their use however and may depart significantly from the norm due to variations in driving habits service practices and differences in road characteristics and climate Traction ABC The traction grades from highest to lowest are A B and C and they represent the tire s ability to stop on wet pavement as measured under test surfaces of asphalt and concrete A tire marked C may have poor traction performance Warning The traction grade assigned to this tire is based on braking straightahead traction tests and does not include cornering turning traction Temperature A B C The temperature grades are A the highest B and C representing the tire s resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel Sustained high temperature can cause the material of the tire to degenerate and reduce tire life and excessive temperature can lead to sudden tire failure The grade C correspond
68. iver s door is opened Low coolant chime Sounds when the engine coolant in the coolant reservoir is low Safety belt warning chime For information on the safety belt warning chime refer to the Seating and safety restraints chapter Supplemental restraint system SRS warning chime For information on the SRS warning chime refer to the Seating and safety restraints chapter 10 Speedometer Indicates the current vehicle speed Optional instrument cluster Taurus SHO cluster Instrumentation 9 79 80 50 0 0 0 0 40 too 120140 16 11 Instrumentation Tachometer Indicates the engine speed in revolutions per minute 3 4 RPMx1000 Optional cluster and Taurus SHO cluster RPMx1000 Engine coolant temperature gauge Indicates the temperature of the engine coolant At normal operating temperature the needle remains within the normal area If it enters the red section the engine is overheating Switch off the ignition and let it cool Refer to Checking and adding engine coolant in the Maintenance and care chapter 12 Odometer Registers the total kilometers mileage of the vehicle Trip odometer Can register the kilometers mileage of individual journeys To reset depress the control
69. k the tether strap hook around the webbing near the center of the shoulder portion of the locked lap shoulder belt 5 Tighten the tether strap Rear seats If you must use a tethered safety seat on one of the rear seats you can anchor the strap to the appropriate tether anchor directly behind that seat position 72 Seating and safety restraints Tether anchorage hardware Attachment holes at each rear outboard seating position have been provided in your vehicle to attach anchor hardware if required Tether anchorage hardware kits part number 613D74 including instructions may be obtained at no charge from any Ford or Lincoln Mercury dealer All vehicles built for sale in Canada include a tether anchor hardware kit Be sure to follow the child safety seat manufacturer s instructions A Tighten the anchor according to specifications Otherwise the safety seat may not be properly secured and the child may be injured in a sudden stop or collision If you have a station wagon tether anchors are already installed for each of the second row seating positions 1 Behind the second seat find the plastic snap on covers for the floor anchors 4 4 2 Use a screwdriver or coin to snap the covers off the anchor in a rearward and upward direction Remove the covers completely 3 Snap the tether strap hook onto the U shaped tether anchor 73 Seating and safety restraints BUILT IN CHILD SEA
70. lders push to open e coin holder and utility bin e cassette CD storage 35 Seating and safety restraints e ashtray push to open The release for the utility compartment is on the front of the console just below the armrest Press and release at the ridges to open If your vehicle is equipped with the column shift it has a center console in the center front seating position The center console has the same features as the full console To open the storage compartment raise the armrest and pull the strap on the seat up and toward the front of the vehicle The cupholders in the center console can be removed for cleaning POSITIVE RETENTION FLOOR MAT IF EQUIPPED Position the floor mat so that the eyelet is over the pointed end of the retention post and rotate forward to lock in Make sure the mat does not interfere with the operation of the accelerator and brake pedal To remove the floor mat reverse the installation procedure 36 Seating and safety restraints OPENING THE TRUNK WITH REMOTE CONTROL IF EQUIPPED Press the remote release control on the instrument panel to the left of the steering wheel LIFTGATE WAGON ONLY You can open the 5 entire liftgate or just KA the liftgate window To the entire liftgat open the entire liftgate 2 L L ress the release i Ky i D button hidden under YV J Y the exte
71. le and make it easier to lose control and roll over 137 Maintenance and care Tires that are larger or smaller than your vehicle s original tires may also affect the accuracy of your speedometer SNOW TIRES AND CHAINS The tires on your vehicle have all weather treads to provide traction in rain and snow However in some climates you may need to use snow tires and chains Follow these guidelines when using snow tires and chains e Use only SAE Class S chains e Install chains securely verifying that the chains do not touch any wiring brake lines or fuel lines e Drive cautiously If you hear the chains rub or bang against your vehicle stop and re tighten the chains If this does not work remove the chains to prevent damage to your vehicle e If possible avoid fully loading your vehicle e Do not use tire chains on aluminum wheels e Do not use tire chains if your vehicle is equipped with P225 55VR16 tires e Remove the tire chains when they are no longer needed Do not use tire chains on dry roads e The suspension insulation and bumpers will help prevent vehicle damage Do not remove these components from your vehicle when using snow tires and chains WHAT YOU SHOULD KNOW ABOUT AUTOMOTIVE FUELS Important safety precautions A Do not overfill the fuel tank The pressure in an overfilled tank may cause leakage and lead to fuel spray and fire 138 Maintenance and care AN If you do not use the proper
72. leaks if you have to add more than a liter quart of engine coolant per month Severe winter climate If you drive in extremely cold climates less than 36 C 34 F it may be necessary to increase the coolant concentration above 50 Refer to the chart on the coolant container to ensure the coolant concentration in your vehicle is such that the coolant will not freeze at the temperature level in which you drive during winter months Never increase the engine coolant concentration above 60 Leave a 50 50 mixture of engine coolant and water in your vehicle year round in non extreme climates CHECKING AND ADDING POWER STEERING FLUID Check the power steering fluid at least twice a year If adding fluid is necessary use only Mercon ATF power steering fluid 1 Start the engine and let it run until it reaches normal operating temperature the engine coolant gauge will be near the center of the NORMAL band 2 While the engine idles turn the steering wheel left and right several times 3 Turn the engine off 129 Maintenance and care 3 0L Vulcan engine 4 Check the fluid level on the dipstick It should be between the arrows in the FULL HOT range Do not add fluid if the level is within this range 5 If the fluid is low add fluid in small amounts continuously checking the level until it reaches the FULL HOT range Be sure to put the dipstick back in the reservoir 3 0L Duratec engine and 3
73. lose moon roof Press AUTO and release to open completely with one touch Press UP or DN on the TILT control to tilt moon roof when closed Sliding shade The moon roof has a sliding shade that you can open or close when the moon roof is closed DOME LAMPS AND MAP LAMPS The front dome lamp is located overhead between the driver and passenger seats If the vehicle is equipped with a moon roof the dome lamp is located behind the moon roof TILT SLIDE 28 Controls and features The dome lamp will stay on if the control is moved to the ON position When the control is in the DOOR position the lamp will only come on when a door is opened If the control is moved to the OFF position the lamp will not come on at all The dome lamp will illuminate whenever a front door is opened If either front door has been opened from the outside the lamp will remain on for 25 seconds after the door is shut If any other door has been opened from the inside the lamp will shut off immediately after the door is closed The map lamps and controls are located on the dome lamp Press the controls on either side of each map lamp to activate the lamps If equipped with a moon roof the map lamps are located on the moon roof control panel Press LIGHT to illuminate the map lamp TILT SLIDE gwg G oy 29 Controls and features POWER WINDOWS Press and hold the rocker switches to
74. n a sudden stop or collision 69 Seating and safety restraints Installing child safety seats in combination lap and shoulder belt seating positions 1 Position the child safety seat in a seat with a combination lap and shoulder belt If you choose to install a child safety seat in the front passenger seat move the seat as far back as possible A Rear facing child seats or infant carriers should never be placed in the front seats 2 Pull down on the shoulder belt and then grasp the shoulder belt and lap belt together y 3 While holding the shoulder and lap belt portions together route the tongue through the child seat according to the child seat manufacturers instructions Be sure the belt webbing is not twisted 70 Seating and safety restraints 4 Insert the belt tongue into the proper buckle for that seating position until you hear A Y and feel the latch engage Make sure the tongue is latched securely by pulling on it 5 To put the retractor in the automatic locking mode grasp the shoulder portion of the belt and pull downward until all of the belt is extracted and a click is heard SE 6 Allow the belt to retract The belt will click as it retracts to indicate it is in the automatic locking mode 7 Pull the lap belt portion across the child seat toward the buckle and pull up on the shoulder belt while pushing down with knee on the child seat to ret
75. ng occupants wagon only A Never use child safety seats in the third seat of a wagon 59 Seating and safety restraints Your vehicle is equipped with safety belts containing an adjust tongue at the rear facing seating positions When the adjust tongue of the lap shoulder combination seat belt is latched into the buckle the tongue will allow the lap portion to become shorter but locks the webbing in place to restrict it from becoming longer Before you reach and latch a combination lap and shoulder belt having an adjust tongue into the buckle you may have to lengthen the lap belt portion of it To lengthen the lap belt pull some webbing out of the shoulder belt retractor While holding the webbing below the tongue grasp the tongue so that it is parallel to the webbing and slide the tongue upward provide enough length so that the tongue can reach the buckle To fasten the belt pull the combination lap and shoulder belt from the retractor so that the shoulder belt portion of the safety belt crosses your shoulder and chest Be sure the belt is not twisted If the belt is twisted remove the twist Insert the tongue into the proper buckle for your seating position until you hear a snap and fell it latch Make sure the tongue is securely fastened to the buckle by pulling on the tongue A The lap belts should fit snugly and as low as possible around the hips not around the waist A Front and rear seat occupants including
76. nly use oil certified for gasoline engines by the American Petroleum Institute Do not use supplemental engine oil additives oil treatments or engine treatments They are unnecessary and could under certain conditions lead to engine damage which is not covered by your warranty CHANGING THE ENGINE OIL AND FILTER Change your engine oil and filter according to the following mileage and time requirements whichever occurs first e Normal Schedule 8 000 km 5 000 miles or six months e Severe Duty Schedule 5 000 km 3 000 miles or three months Severe duty operation would include extensive idling trailer towing driving in severe dust and police taxi or delivery service Ford production and aftermarket Motorcraft oil filters are designed for added engine protection and long life If a replacement oil filter is used that does not meet Ford material and design specifications startup engine noises or knock may be experienced It is recommended you use the appropriate Motorcraft oil filter or another brand meeting Ford specifications for your engine application 124 Maintenance and care BRAKE FLUID CHECKING AND ADDING BRAKE FLUID Brake fluid should be checked and refilled as needed at least once each year e Clean the reservoir m avg een Tq cap before removal Z 2 o to prevent dirt or edge water from entering the reservoir Visually inspect the fluid level If necessary add b
77. nnections and trailer wheel lug nuts e When stopped in traffic for long periods of time in hot weather place the gearshift in P Park and increase idle speed This aids engine cooling and air conditioner efficiency e Vehicles with trailers should not be parked on a grade If you must park on a grade place wheel chocks under the trailer s wheels 97 Driving FUEL CONSUMPTION Fuel economy can be improved by avoiding e lack of regular scheduled maintenance e excessive speed e rapid acceleration 98 Roadside emergencies HAZARD LIGHTS CONTROL Use only in an emergency to warn traffic of vehicle breakdown approaching danger etc Depress to activate all indicators simultaneously Depress again to switch off The warning lights can be operated when the ignition is off FUEL PUMP SHUT OFF SWITCH If the engine cranks but does not start after a collision the fuel pump shut off switch may have been activated The shut off switch is a device intended to stop the electric fuel pump when your vehicle has been involved in a substantial jolt 1 Turn the ignition switch to the OFF position 2 Check the fuel system for leaks 3 If no fuel leak is apparent reset the fuel pump shut off switch by pushing in the button on the switch 4 Turn the ignition switch to the ON position Pause for a few seconds and return the key to the OFF position 5 Make a further check for leaks in the fuel system 99 R
78. normal driving conditions F or manual control start in 1 First and then shift manually If your vehicle is equipped with a console mounted gearshift you must press the thumb button on the side of the gearshift to move the gearshift from P Park 88 Driving Understanding gearshift positions P Park Always come to a complete stop before shifting into P Park Make sure the gearshift is securely latched in P Park This locks the transaxle and prevent the front wheels from rotating R Reverse With the gearshift in R Reverse the vehicle will move backward You should always come to a complete stop before shifting into and out of R Reverse PRN D1 P RND21 89 Driving N Neutral With the gearshift in the N Neutral position the vehicle can be started and is free to roll Hold the brake pedal down while in this position Overdrive column shift without O D OFF switch or D Overdrive column or console mounted gearshift with O D off switch The overdrive position is the normal driving position for an automatic overdrive transaxle It works the same way as D Drive or D Overdrive with the O D OFF switch not depressed works but shifts to a fourth gear an overdrive gear when your vehicle cruises at a constant speed for any length of time This fourth gear will increase your fuel economy when you travel at cruising speeds Overdrive
79. nough to activate the light sensor The closer the thumbwheel is to the MAX mark the longer the lamps will stay on after leaving the vehicle The autolamps will now automatically turn the headlamps on and off for you To turn the autolamps off move thumbwheel back to the OFF position Daytime running lights Canadian vehicles only The daytime running light system turns the headlamps on with a reduced light output when e the engine is running e the parking brake is released e the headlamp system is in the OFF position A The Daytime Running Light DRL system will not illuminate the tail lamps and parking lamps Turn on your headlamps at dusk Failure to do so may result in a collision CLIMATE CONTROL SYSTEM Manual heating and air conditioning system Fan speed control Controls the volume of air circulated in the vehicle 15 Controls and features Mode selector control Controls the direction of the airflow to the inside of the vehicle e MAX A C Uses recirculated air to cool the vehicle It allows for faster cooling but is noisier than A C The air conditioning compressor will operate in this mode e A C Uses outside air to cool the vehicle It is quieter than MAX A C but not as economical The air conditioning compressor will operate in this mode e VENT Distributes outside air through the instrument panel registers e OFF Outside air is shut out and the fan will not operate
80. o NHTSA U S Department of Transportation 400 Seventh Street Washington D C 20590 You can also obtain other information about motor vehicle safety from the Hotline 168
81. o be replaced Electronic Automatic Temperature Control EATC system if equipped The EATC system will maintain a selected temperature and automatically control airflow You can override automatic operation with any of the six override controls at the bottom of the control panel 17 Controls and features To turn on the EATC Press AUTO or any of the six manual override buttons along the bottom of the control The control will operate only when the ignition is turned to the ON position To turn off the EATC Press OFF When the system is off the display window will be blank dark Automatic operation Press AUTO and select the desired temperature The system will automatically determine fan speed and airflow location Fan speed remains automatic unless you press FAN The selected temperature will be shown on the display Temperature selection TEMP will increase or decrease the set temperature Pressing TEMP will change the temperature one degree in either direction Pressing and holding TEMP will rapidly change the temperature in one degree increments in either direction until either 18 C 65 F or 29 C 85 F The temperature will then jump 15 C 5 F and stop at either 16 C 60 F which is maximum cooling or 32 C 90 F which is maximum heating Ge Pt Ls o 18 Controls and features Changing modes Temperature conversion Press MAX A C and the Y F DEF
82. oadside emergencies If you have a sedan the fuel pump shut off switch is located on the right side of the trunk behind the trunk liner If you have a wagon the switch is located behind the service panel on the right side of the cargo area FUSES AND RELAYS Fuses If electrical are components in the le Adiel vehicle are not E working a fuse may have blown Blown fuses are identified by a broken wire Check the appropriate fuses before replacing any electrical components AN Always replace a fuse with one that has the specified amperage rating Using a fuse with a higher amperage rating can cause severe wire damage and could start a fire 100 Roadside emergencies Standard fuse amperage rating and color Passenger compartment fuse panel The fuse panel is located below and to the left of the steering wheel by the brake pedal Pull the panel cover outward to access the fuses To remove a fuse use the fuse puller tool provided on the fuse panel cover The fuses are coded as follows Fuse Relay Fuse Amp Description Location Rating Po Not used O 2 5A Instument illumination 101 Roadside emergencies Fuse Relay Fuse Amp Description e let lee headlamp headlamp 5 5A Brake shift interlock rear defroster MLPS switch backup lamps speed control climate control starter relay 5A Powe
83. on plate is located on the front panel of the engine compartment This plate bears technical information on your vehicle and identifies various components Vehicle identification number The vehicle identification number VIN is attached to a metal tag and is located in the following areas 166 Capacities and specifications of your vehicle for maximum theft protection e left and right front fenders e hood e left and right front doors e front and rear bumpers e left and right rear quarter panels e decklid e liftgate e engine compartment e transaxle Engine number The engine number is stamped on the engine block 167 Reporting safety defects REPORTING SAFETY DEFECTS U S ONLY If you believe that your vehicle has a defect that could Ae a crash or could cause ED injury or death you should immediately inform the National Highway Traffic Safety Administration NHTSA in addition to Ford Motor Company If NHTSA receives similar complaints it may open an investigation and if it finds that a safety defect exists in a group of vehicles it may order a recall and remedy campaign However NHTSA cannot become involved in individual problems between you your dealer or Ford Motor Company To contact NHTSA you may either call the Auto Safety Hotline toll free at 1 800 424 9393 202 366 0123 in the Washington D C area or write t
84. orn will chirp once to let you know that the system is armed If the doors or liftgate wagon are not closed and you press the remote entry transmitter twice to confirm the doors are locked the horn will chirp twice to warn you that the system is not arming Disarming the system You can disarm the system by any of the following actions e Unlock the doors by using your remote entry transmitter e Unlock the doors by using your keyless entry pad e Unlock the doors or liftgate with a key Turn the key full travel toward the front of the vehicle to make sure the alarm disarms e Turn ignition to ACC or ON 48 Seating and safety restraints e Press PANIC on remote entry transmitter This will disarm the system when alarm is triggered or sounding CODED KEY ANTI THEFT SYSTEM IF EQUIPPED Your vehicle is equipped with a coded key anti theft system Only the correct key will be able to start your vehicle If your keys are lost or stolen you must take your vehicle to a Ford dealership for re programming Programming additional keys If you need additional keys electronically coded for your vehicle spares can be purchased total of 16 keys To program a new key perform the following procedure 1 With the coded key in the ignition turn the ignition from ON to OFF 2 Within 15 seconds of THEFT turning ignition off insert new electronic key into the ignition and turn it from OFF to O
85. ou fuel your vehicle To check the oil 1 Make sure the vehicle is on level ground If the engine is warm turn the engine off and wait a few minutes for the oil to drain into the oil pan 2 Set the parking brake and ensure the gearshift is securely latched in P Park 3 Open the hood Protect yourself from engine heat 4 Locate and carefully remove the engine oil dipstick 5 Wipe the dipstick clean Insert the dipstick fully then remove it again The oil level should be in the range shown on the dipstick 6 If the oil level is below the MIN line or the ADD 1 QUART line add oil as necessary If the oil level is beyond the MAX or FULL line engine damage or high engine oil consumption may occur and some oil must be removed from the engine by a service technician 7 Put the dipstick back in and ensure it is fully seated Adding engine oil 1 Check the engine oil For instructions refer to Checking the engine oil in this chapter 2 If the fluid level is not within the normal range add only certified engine oil of the preferred viscosity Add engine oil through the oil filler cap 123 Maintenance and care Remove the filler cap and use a funnel to pour oil in the opening 3 Recheck the oil level Make sure the oil level is not above the MAX or FULL mark on the dipstick ENGINE OIL RECOMMENDATIONS Use SAE 5W 30 motor oil meeting Ford specification WSS M2C153 F or equivalent O
86. over the edge of the seat cushion You may wish to discuss the special needs of your child with your pediatrician SAFETY SEATS FOR CHILDREN Child and infant or child safety seats Use a safety seat that is recommended for the size and weight of the child Carefully follow all of the manufacturer s instructions with the cafety seat you put in your vehicle If you do not install and use the safety seat properly the child may be injured in a sudden stop or collision When installing a child safety seat 68 Seating and safety restraints Use the correct safety belt buckle for that seating position Make sure the tongue is securely fastened in the buckle Keep the buckle release button pointing up and away from the safety seat with the tongue between the child seat and the release button to prevent accidental unbuckling Place seatback in upright position Put the safety belt in the automatic locking mode Refer to Using the automatic locking mode Ford recommends the use of a child safety seat having a top tether strap Install the child safety seat in a seating position which is capable of providing a tether anchorage For more information on top tether straps refer to Attaching safety seats with tether straps h Carefully follow all of the manufacturer s instructions included with the safety seat you put in your vehicle If you do not install and use the safety seat properly the child may be injured i
87. pregnant women should wear safety belts for optimum protection in an accident 60 Seating and safety restraints A Each seating position in your vehicle has a specific safety belt assembly which is made up of one buckle and one tongue that are designed to be used as a pair 1 Use the shoulder belt on the outside shoulder only Never wear the shoulder belt under the arm 2 Never swing it around your neck over the inside shoulder 3 Never use a single belt for more than one person Due to folding rear seats sometimes the buckles and tongues toward the center of the vehicle may be hidden by the rear edge of the seat cushion Pull them out so they will be accessible While you are fastened in the seat belt the shoulder belt adjusts to your movement However if you brake hard turn hard or your vehicle receives an impact of 8 km h 5 mph or more the safety belt will become locked and help reduce your forward movement To unfasten the belt push the red release button on the end of the buckle This allows the tongue to unlatch from the buckle While the belt retracts guide the tongue to its original position to prevent it from striking you or the vehicle Safety belt extension assembly If the safety belt assembly is too short even when fully extended eight inches can be added to the safety belt assembly by adding a safety belt extension assembly part number 611C22 Safety belt extension assemblies can be obtained from you
88. r dealer at no cost This assembly is not for use in the wagon s rear facing seat Use only extensions manufactured by the same supplier as the safety belt Manufacturer identification is located at the end of the webbing on the label Also use the safety belt extension only if the safety belt is too short for you when fully 61 Seating and safety restraints extended Do not use extensions to change the fit of the shoulder belt across the torso Safety belt warning light and indicator chime The seat belt warning light illuminates in the instrument cluster and a chime sounds to remind the occupants to fasten their safety belts Conditions of operation The driver s safety The safety belt indicator belt is not buckled illuminates for one to two before the ignition minutes and the warning key is turned to ON chime sounds for four to eight seconds The driver s side The safety belt indicator safety belt is buckled light and warning chime while the indicator turn off light is illuminated and the warning chime is sounding The driver s safety The safety belt warning belt is buckled before light and indicator chime the ignition key is remain off turned to ON Safety belt maintenance Check the safety belt systems periodically to make sure they work properly and are not damaged Check the safety belts to make sure there are no nicks wears or cuts All safety belt assemblies including retractors buckl
89. r antenna radio control unit GEM Anti lock brakes system Central Temperature Monitor EEEC relay ignition coil passive anti theft system radio Air bag indicator instrument cluster 102 Roadside emergencies Location Rating Instrument cluster autolamps transmission control switch integrated control panel GEM Air bag blower motor electronic automatic temperature control Lamp outage indication Semi active suspension SHO only Multi function switch turn signal front Headlamp rear Integrated control panel remote entry cigar lighter 103 Roadside emergencies Location Rating zi fpo Cigar Tighter _ 22 oa mirrors power antenna decklid lamps autolamps Wiper system variable assist steering remote entry anti theft Integrated control panel speedometer electronic automatic temperature control module 2o e connector a26 SA Trrunklid relay gt stop control pe a function peo hazard flashers High beams daytime running lamps instrument cluster sp SAC Tail lamp feed 104 Roadside emergencies Location Rating 32 10A Integrated control panel heated mirrors 33 5A Power windows lock illumination as a de relay ka unlock relay T p relay Z am relay 38 One touch window down relay relay Power distribution box The power distribution box is located in the engine compartment near the battery The
90. ract to remove any slack in the belt 9 Before placing the child in the seat forcibly tilt the seat forward and back to make sure the seat is securely held in place 10 Try to pull the belt out of the retractor to make sure the retractor is in the automatic locking mode R 8 Allow the safety belt R gt KN 71 Seating and safety restraints you should not be able to pull more belt out If the retractor is not locked unbuckle the belt and repeat steps two through nine Check to make sure the child seat is properly secured before each use Attaching safety seats with tether straps Some manufacturers make safety seats that include a tether strap that goes over the back of the vehicle seat and attaches to an anchoring point Other manufacturers offer the tether strap as an accessory Contact the manufacturer of your child safety seat for information about ordering a tether strap Front seats To install a tether from a child safety seat in the front seat 1 Buckle the lap shoulder belt in the seat behind the front passenger seat in which the child safety seat will be installed 2 Pull all the stored belt out of the rear seat retractor to switch the retractor to automatic locking mode 3 Let the retractor wind up the slack from the lap shoulder belt 4 Install the child safety seat in the front seat Refer to Installing child safety seats in combination lap and shoulder belt seating positions Hoo
91. rake fluid until the level reaches MAX Do not fill above this line Use only a DOT 3 brake fluid certified to meet Ford specifications Refer to Lubricant specifications in the Capacities and specifications chapter A Brake fluid is toxic AN If you use a brake fluid that is not DOT 3 you will cause permanent damage to your brakes Do not let the reservoir for the master cylinder run dry This may cause the brakes to fail 125 Maintenance and care CHECKING AND ADDING WASHER FLUID Check the washer fluid whenever you stop for fuel The reservoir is highlighted with a washer symbol If the level is low add enough fluid to fill the reservoir In very cold weather do not fill the reservoir all the way Checking and adding washer fluid for the liftgate wagon only The opening for the reservoir is located on the passenger side under the tail lamp Refill this reservoir with the same fluid you use for your windshield CHECKING AND ADDING ENGINE COOLANT Check the level of the coolant in the reservoir at least once a month Be sure to read and understand Precautions when servicing your vehicle in this chapter If the engine coolant has not been checked for a long period of time the engine coolant reservoir may eventually empty If this occurs add engine coolant 126 Maintenance and care to the coolant reservoir For more information on engine coolant maintenance refer to Adding
92. rior trim panel just above the license plate You must lock the liftgate with the key or power lock control it does not lock automatically The window locks when the liftgate is locked To open the window make sure the liftgate and window are unlocked then press the outside lock cylinder The window can only be opened from the outside To prevent any damage to the liftgate and window close them completely before driving 37 Seating and safety restraints STORAGE COMPARTMENT nee ONLY Your vehicle comes equipped with a storage compartment in the floor of the cargo area An additional compartment is in the rear trim panel on the right Always put the load you are carrying as far forward as possible CARGO NET IF EQUIPPED The cargo net secures lightweight objects in the cargo area Attach the net to the anchors provided Do not put more than 22 kg 50 Ibs in the net This net is not designed to restrain objects during a collision CARGO COVER WAGON IF EQUIPPED You can cover the rear compartment by fastening the cover into the pockets in the trim panel make sure the cover is right side up so it unrolls from the top then pulling and hooking the cover into the pockets into the trim panel REWINDING THE SLIDING SHADE If the shade is damaged or loses its spring tension from excessive use manual rewinding of the shade may be necessary The following procedure is
93. rive your vehicle if it does not operate properly See your dealer if the engine runs on for more than five seconds after you shut it off or if it misfires surged stalls or backfires Information about your vehicle s emission system is on the Vehicle Emission Control Information decal located on or near the engine This decal identifies engine displacement and gives some tune up specifications Readiness for inspection maintenance testing In some localities it may become a legal requirement to pass an Inspection Maintenance I M test of the On board Diagnostic OBD II system If the vehicle s powertrain system or its battery has just been serviced the OBD II system is reset to a not ready for I M testing condition To prepare for I M testing the law specifies that additional mixed city and highway driving is required to complete the check of the OBD II system The driving modes required to reach the ready condition consist of a minimum of 30 minutes of city and highway driving as described below e At least twenty minutes driving in stop and go city type traffic with at least four idle periods e At least ten minutes of driving on an expressway or highway Before completing the above driving modes the engine must be warmed up and at operating temperature Once started the vehicle must not be turned off during these driving modes EXTERIOR LAMPS It is a good idea to check the operation of the following lights freq
94. rmitted maximum speeds INFORMATION ABOUT THIS GUIDE The information found in this guide was in effect at the time of printing Ford may change the contents without notice and without incurring obligation 2 Instrumentation Engine coolant Tachometer temperature gauge pg 12 oe nel pg 12 Speedometer pg 11 Headlamp control pg 14 Remote trunk release nols pg 37 Driver air bag pg 23 Parking brake pg 64 release Turn signal wiper 85 pg 85 washer control pg 26 if equipped 4 Instrumentation Electronic sound system refer to Audio Giude pg 22 Climate control pg 15 Gearshift floor mounted shown pg 86 Instrumentation WARNING LIGHTS AND GAUGES Standard instrument cluster SHO cluster if equipped Instrumentation Turn signal IIluminates when the left or right turn signal or the hazard lights are 5 gt turned on High beams Illuminates when the headlamp high beams are on D Safety belt IIluminates when the ignition is switched on hb to remind you to fasten A your safety belts For more information refer to Using the safety restraints properly in the Seating and safety restraints chapter Door ajar IIluminates when the A aniti iteh ic j AAs ignition switch is in the ren ON or START position and any door is
95. s to a level of performance which all passenger car tires must meet under the F ederal Motor Vehicle Safety Standard No 109 Grades B and A represent higher levels of performance on the laboratory test wheel than the minimum required by law A The temperature grade for this tire is established for a tire that is properly inflated and not overloaded Excessive speed underinflation or excessive loading either separately or in combination can cause heat buildup and possible tire failure 136 Maintenance and care SERVICING YOUR TIRES Checking the tire pressure e Use an accurate tire pressure gauge e Check the tire pressure when tires are cold after the vehicle has been parked for at least one hour or has been driven less than 5 km 3 miles e Adjust tire pressure to recommended specifications found on the Safety Compliance Certification Label A Improperly inflated tires can affect vehicle handling and can fail suddenly possibly resulting in loss of vehicle control Tire rotation Because your vehicle s tires perform different jobs they often wear differently To make sure your tires wear evenly and last longer rotate them as indicated in the Service Guide If you notice that the tires wear unevenly have them checked Replacing the tires Replace the tires when the wear band is visible through the tire treads IN BAMA A Failure to follow these precautions may adversely affect the handling of the vehic
96. sed but performance may decrease We do not recommend gasolines labeled as premium in high altitude areas that are sold with octane ratings less than 91 Fuel quality If you are experiencing starting rough idle or hesitation problems try a different brand of fuel If the condition persists see your dealer or a qualified service technician The American Automobile Manufacturers Association AAMA issued a gasoline specification to provide information on high quality fuels that optimize the performance of your vehicle We recommend the use of gasolines that meet the AAMA specification if they are available It should not be necessary to add any aftermarket products to your fuel tank if you continue to use a high quality fuel Cleaner air Ford approves the use of gasolines to improve air quality including reformulated gasolines that contain oxygenates such as a maximum of 10 ethanol or 15 MTBE There should be no more than 5 methanol with cosolvents and additives to protect the fuel system Calculating fuel economy To accurately calculate your vehicle s fuel economy 141 Maintenance and care 1 Fill the tank completely and record the initial odometer reading 2 Each time you fill the tank record the amount of fuel added in liters or gallons 3 After at least three to five fuel tank fill ups fill the fuel tank and record the current mileage reading 4 Use one of the following equations to calculat
97. the shoulder belt height push the button and slide the height control down To raise the height of the shoulder belt slide the height adjuster up Pull down on the height adjustment assembly to make sure it is locked in place Center rear lap belt sedan The safety belt in the center rear seating position has a detachable shoulder belt 58 Seating and safety restraints To attach the shoulder belt to the lap belt pull the shoulder belt out from the retractor in the seatback and insert into the lap belt connecting pin into the wide end of the key slot on the shoulder belt Pull the connecting pin into the narrow end of the key slot until you hear a snap and feel it latch Make sure the shoulder belt is securely fastened to the lap belt by pulling up on the shoulder belt Lap belts The lap belts in the center front seating position if equipped and center rear seating position wagon do not adjust automatically You must adjust them to fit snugly and low as possible around your hips Do not wear the lap belt around your waist Make sure you insert the tongue into the correct buckle If you need to lengthen the belt turn the tongue at a right angle to the belt and pull across your lap until it reaches the buckle If you need to tighten the belt pull the loose end of the belt through the tongue until it is snugly across the hips Shorten and fasten the belt when not in use Safety belts for rear faci
98. to engage the lock Move control down to disengage childproof locks CONSOLE If your vehicle is equipped with a floor mounted gearshift it will have a full console with the following features e cup holders push to open 32 meee Controls and features e coin holder and utility bin e cassette CD storage e cellular phone if equipped as 2A e ashtray push to open The release for the utility compartment is on the front of the console just below the armrest Press and release at the ridges to open 33 Controls and features If your vehicle is equipped with a cellular phone press the latch release located on the driver s side edge of the console lid to access the phone If your vehicle is equipped with the column shift it has a center console in the center front seating position The center console has the same features as the full console To open the storage compartment raise the armrest and pull the strap on the seat up and toward the front of the vehicle The cupholders in the center console can be removed for cleaning Cellular phone Refer to the cellular phone user s manual for instruction on operation 34 Seating and safety restraints CONSOLE If your vehicle is equipped with a floor mounted gearshift it will have a full console with the following features e cup ho
99. uently 144 Maintenance and care Headlamps High mount brake lamp Tail lamps Brake lamps Backup lamps e Hazard flashers e Turn signals e License plate lamp e Interior overhead lamps Do not remove lamp bulbs unless they will be replaced immediately If a bulb is removed for an extended period of time contaminants may enter the lamp housings and affect performance High mount brake lamp Sedan To remove the brake lamp 1 Remove package tray trim then push attachment toward the rear 2 Slide brake lamp up and away from the rear window to remove it from the tabs that hold it down 3 Disconnect bulbs To install brake lamp 1 Install bulbs then position the brake lamp over tab slots and line up the tab with the tab slots 2 Push down and toward the rear window to engage the tabs 3 Push attachment toward the rear window and line up slot in attachment with the edge of the sheet metal screw 145 Maintenance and care 4 Release the attachment slot onto the sheet metal hole Install the package tray trim High mount brake lamp Wagon To remove the brake lamp 1 Remove interior trim panel then remove the three attachment nuts that hold brake lamp in place 2 Lift whole assembly off vehicle from the outside 3 Disconnect bulbs To install brake lamp 1 Install bulbs the position brake lamp into tailgate holes 2 From the inside of the vehicle stall and tighten the fo
100. ur chances of having a collision greatly increase Trailer lamps Trailer lamps are required on most towed vehicles Make sure your trailer lamps conform to local and Federal regulations See your dealer or trailer rental agency for proper instructions and equipment for hooking up trailer lamps 96 Driving Driving while you tow Do not drive faster than 72 km h 45 mph with any weight on the trailer while towing on a hot day or in hilly country Cruise control may shut off if you are towing on long steep grades When towing a trailer e Use 2 Second if equipped or 1 First when towing up or down steep hills This will eliminate excessive downshifting and upshifting for optimum fuel economy and transaxle cooling e Anticipate stops and brake gradually Servicing after towing If you tow a trailer for long distances your vehicle will require more frequent service intervals Refer to the Service Guide for more information Trailer towing tips e Practice turning stopping and backing up in an area before starting on a trip to get the feel of the vehicle trailer combination When turning drive slightly beyond the normal turning point so the trailer wheels will clear curbs and other obstacles e Allow more room for stopping with a trailer attached e The trailer tongue weight should be 10 15 of the loaded trailer weight e After you have traveled 80 km 50 miles thoroughly check your hitch electrical co
101. ur nuts that hold the brake lamp in place 3 Install the interior trim panel Using the right bulbs Function Trade Number 211 2 146 Maintenance and care Dome lamp moon roof vanity passenger driver Door courtesy lamp Floor console Luggage compartment lamp Glove compartment Instrument courtesy lamps I P_ ashtray lamp lamp Radio illumination Clock Warning indicator lights except THEFT warning Cluster illumination Heater A C Automatic climate control Rear window defrost switch rade Number 08 74 194 68 o to Ford authorized radio service center Go to Ford authorized dealer Go to Ford authorized dealer Go to Ford authorized dealer Go to Ford authorized dealer Go to Ford authorized dealer Go to Ford authorized dealer Go to Ford authorized dealer 147 Maintenance and care Function Trade Number to Ford authorized dealer Rear window _ wiper washer ap switch wagon Headlamps To remove the headlamp bulb 1 Make sure headlamp switch is in OFF position then open the hood If you are replacing the driver side headlamp unclip the electronic module on the right side of the battery and move it out of the way 2 Remove the electrical connector from the bulb by pulling the connector CD aes 3 Remove the bulb retaining ring by rotating it counterclockwise when viewed from the rear about an eighth of a t
102. urn to free it from the bulb socket and by sliding the ring off the plastic base Keep the ring because it will be used again to retain the new bulb 4 Remove the old bulb from its socket by gently pulling it straight back out of the socket Do not turn the bulb while you are removing it To install the new bulb 148 Maintenance and care 1 With the flat side of the bulb s plastic base facing upward insert Gey glass end of the bulb i into the socket You may need to turn the bulb left or right to line up the grooves in the plastic base with the tabs in the socket When the grooves are aligned push the bulb into the socket until the plastic base contacts the rear of the socket 2 Slip the bulb retaining ring over the plastic base until it contacts the rear of the socket by rotating it clockwise until you feel a stop 3 Push the electrical connector into the rear of the plastic base until it snaps locking it into position 4 Turn the headlamps on and make sure they work properly If the headlamp was correctly aligned before you changed the bulb you should not need to align it again AIMING THE HEADLAMPS Your vehicle is equipped with a Vehicle Headlamp Aim Device VHAD on each headlamp body Each headlamp may be proeprly aimed in the horizontal direction left right and the vertical position up down A non zero bubble reading does not necessarily indicate out of aim headlamps If your ve
103. ve a P suffix If a spark plug needs to be replaced use only spark plugs with the service part number suffix letter PP as shown on the engine decal 3 0L Duratec engine Air filter FA 1630 F uel filter F G 800 A BXT 36R F uel filter F G 800 A 156 Capacities and specifications Passenger FP 6 compartment air filter if equipped Oil filter L 820 S PCV valve EV 152 Spark plug AWSF 32F 3 4L SHO engine Air filter Battery Fuel filter Passenger compartment air filter if equipped REFILL CAPACITIES 3 0L Vulcan engine Ford Part Vehicle Capacity Name Type Brake High All Fill to line fluid performance in reservoir DOT 3 brake fluid Engine Premium All 11 0 11 6 coolant cooling system fluid 157 Capacities and specifications insole Name Type Engine oil Motocraft All 4 25 4 5 with motor oil filter 5W30 super change premium capacity gallons Power Motorcraft All Fill to line in steering MERCON reservoir fluid ATF Automatic Motorcraft All 12 8 13 5 transaxle MERCON AX4N ATF Automatic Motorcraft All 11 6 12 2 transaxle MERCON AX4S ATF indshield Ultra clear All windshield Wagon washer concentrate 3 0L Duratec engine Ford Part Vehicle Capacity Name Type Brake High All Fill to line fluid performance in reservoir DOT 3 brake fluid Engine Premium All 10 0 10 6 coolant cooling system fluid 158 Capaciti
104. wrench Pry only at the notch Do not use a screwdriver or any other tool as this may damage the wheel cover surface finish 112 Roadside emergencies 2 Remove the center bolt on the wheel cover with the lug wrench tip 3 To remove the wheel cover pry it loose by inserting the tapered end of the lug wrench between the wheel cover and wheel To replace the wheel cover 1 One of the windows on the wheel cover is identified with a valve stem logo on the back side of the wheel cover Install the wheel over the wheel with the window at the valve stem 2 Hold the wheel cover in this position and press the cover onto the wheel with the palm of your hand Do not force or hammer the cover 3 Attach the bolt to the pedestal through the center hole on the cover with the lug wrench 4 Align the legs of the center ornament with the slots of the wheel cover Reinstall the ornament by pressing with the palm of your hand Do not hammer or force the cover Anti theft lug nuts if equipped If your vehicle is a equipped with this 6 feature one of the lug O GY nuts on each wheel must be removed and replaced with a special key The key and registration card are attached to the lug wrench and stored with the spare tire If you lose 113 Roadside emergencies the key send the registration card to the manufacturer not the dealer to get a replacement key If the lug wrench lug nut key assembly is lost see
105. y restraints AN The rear seatback must be fully locked before operating the child restraint system 1 Grasp the child seat at the top of the seatback and pull the top forward to release the latch 2 Continue to unfold the child seat until it rests on the seat 3 Read all information and warnings on the child seat cushion and shoulder safety belt Make sure the child is not too large for the child seat Seating and safety restraints 4 If connected squeeze the top and the bottom of the right half of the chest clip and pull to separate both halves 5 Place the child on the child seat and position the shoulder belts over each shoulder 6 Insert either the left or the right safety belt tongue into the single opening of the crotch safety belt buckle it doesnt matter which tongue is inserted first Insert other tongue The color green must appear in the indicator window on the crotch safety belt buckle when buckled Allow belts to retract and fit snugly 7 Fasten both halves of the chest clip below 00 the child s shoulders i mo and adjust it to i comfortably hold the shoulder belts in place on the child s chest The color green must appear in the indicator window when fastened 8 Pull the shoulder belts toward you to make sure the crotch safety belt buckle is properly fastened and the retractor is locked 9 If the belts become too tight unbuckle the crotch safety belt buckle to unlock the
106. ystem does not work use the key or remote entry transmitter s 1 To unlock the driver s door enter one of the two codes After pressing the fifth number the driver s door unlocks 2 To unlock the passenger s door s and liftgate wagon press the 3 4 button within five seconds of unlocking the driver s door 3 To unlock the trunk or liftgate wagon enter the five digit factory code then press the 5 6 button within five seconds Locking the doors with the keyless entry system To lock all the doors m press 7 8 and 9 0 at the fi IT same time It is not necessary to first enter the keypad code 41 Seating and safety restraints Operating your perimeter anti theft system if equipped from the keyless entry pad The keyless entry system arms by pressing 7 8 and 9 0 To disarm or reset a triggered anti theft alarm enter the five digit code All doors must be fully closed for the anti theft system to arm Refer to the Anti theft system section if equipped in this chapter for more details Autolock The autolock feature is part of your remote keyless entry system which locks all of the doors when e all vehicle doors are closed e the ignition key is turned to the ON position e the brake pedal is pressed e you shift through R reverse e one second has elapsed after the brake pedal is released The autolock feature repeats when e a door is opened and then all doors are closed e

10 - Taurus

Contents

Download Pdf Manuals

Related Search

Related Contents