Implementation of Modern Vigilance Control Device Using GSM and
Contents
1. International Journal of Latest Trends in Engineering and Technology IJLTET Implementation of Modern Vigilance Control Device Using GSM and GPS Technology Ch Sindhura Department of Electronics and Communication Engineering Gudlavalleru Engineering College Gudlavalleru Andhra Pradesh India B R B Jaswanth Assistant Professor Department of Electronics and Communication Engineering Gudlavalleru Engineering College Gudlavalleru Andhra Pradesh India Abstract This paper is proposed to prevent train accidents due to un alertness of engine drivers by designing engines with a new emergency braking system Modern VCD Vigilance Control Device a microcontroller based safety device which will enhance passenger s safety by cyclically generating warnings and by automatically stopping the train if the driver is incapacitated or dead or fast asleep This paper also informs the position of the loco crew to the higher authorities and tracks the position of the train where it is stopped by using Global System for Mobile communication GSM and Global Positioning System GPS technologies If the driver does not perform a regular task such as accelerating or braking for a stipulated period of time a message will be send to the Vigilance Control Officer VCO through GSM After the train is stopped automatically its position is tracked by GPS and a message will be send to the Vigilance officer Keywords Driver Control GPS GSM Loco Vigilanc2. PS module ST22 which is having TTL logics and also RS232 as option The GPS receiver is shown in Figure 2 b This GPS is used to track the position of the train after the emergency brake is applied in order to avoid the accidents This application is used only after the train is stopped Vol 2 Issue 4 July 2013 404 ISSN 2278 621X International Journal of Latest Trends in Engineering and Technology IJLTET TTL Out Yellow gt TTL In Blue RS 232 Out White R5 232 In Green 5 Volts GND a b Figure 2 a GSM Modem Prototype b GPS Receiver B Working VCD is microcontroller based equipment designed and manufactured to enhance the safety of the locomotive operation by ensuring the alertness of the crew all the time The system is resetting type and operates in a fail safe manner VCD will give cyclic warnings to the driver Based on the drivers reaction to these warnings in terms of pre defined set of actions to be done by the driver the system will automatically reset the alerting cycle The locomotive driver operates controls for increasing and decreasing locomotive power application or releasing the breaks or operating the horn of the locomotive The VCD monitors whether these controls have been operated by the driver in a 60 second time period In case the driver has not operated any controls the VCD gives a visual warning by activating a flashing light for 8 seconds If acknowledgement is not received an additi
3. e Warnings I INTRODUCTION In Indian Railways major accidents have been caused due to failure of Railway staff Higher incidence of human failures surface as technical safeguards and backups do not always replace the human effort Though an accident occurs only when both fail but it usually gets logged as human error with a tendency of glossing over technical failure Under optimum field conditions and with the best of intentions a human being 1s likely to commit a mistake from time to time This is the reason why operating rules included many redundancies in safety procedures and operating practices involve number of checks and balances More and more automation is resorted to prevent human errors This paper provides a method to safety of the passengers in trains by alerting the driver cyclically Vigilance control device plays a major role to reduce the accidents that are caused by the pilot of the train Vigilance Control Device VCD is a microcontroller based safety device which will automatically apply penalty brakes in case the driver is incapacitated or dead Similar operation is available in older locomotives in the form of Dead man s Lever The dead man s lever is a knob that has to be kept pressed at all times to keep the train running This system was introduced to prevent accidents even if the driver died at his controls hence the name Unless a certain amount of pressure is maintained on the lever brakes get automatically activa
4. interfaced with the microcontroller operates in 900MHz frequency and is operated at voltage levels of 3 5 to 5V The working of GSM modem is based on commands the commands always start with AT which means ATtention and finish with a lt CR gt character AT commands are used to control the MODEMs Since one of the main objective for this application is to show how to send the message only a subset of the AT command set needs to be implemented The AT commands are given to the GSM modem with the help of PC or controller The Global Positioning System GPS is a satellite based navigation system that sends and receives radio signals A GPS receiver acquires these signals and provides the user with information Using GPS technology one can determine location velocity and time 24 hours a day in any weather conditions anywhere in the world for free The basis of the GPS technology is a set of 24 satellites that are continuously orbiting the earth These satellites are equipped with atomic clocks and sent out radio signals as to the exact time and location These radio signals from the satellites are picked up by the GPS receiver Once the GPS receiver locks on to four or more of these satellites it can triangulate its location from the known positions of the satellites It is a higher performance low power satellite based model It is a cost effective and portable system which accurately detects the location The GPS receiver used here is Sky Traq Venus 6 G
5. onal audio alarm is given for 8 sec If driver further fails to acknowledge the alarm a message is send to guard and to signal inspector through GSM modem as DRIVER IS NOT ALERT here guard is provided with break to control the VCD If guard is not applying break within 10 sec then message is sent to signal inspector as DRIVER AND GUARD NOT ALERT and VCD will initiate the automatic application of brakes and it informs the position of the train where it is stopped in the form of latitude and longitude through GSM by using GPS module MU mode is the multiple unit used when the efficiency of the one engine is not sufficient for pulling the trains in hilly areas then it is provided for utilizing the efficiency of the second engine it is required to operate in mu mode When VCD is operated in MU mode the above operation of the VCD cycle should not be activated in the second engine that is the driver is provided only in one cabin so it is programmed that when VCD operates in MU mode the entire VCD cycle at second engine should not activate The flow chart shown in Fig 2 gives the clear explanation of the working of the modern vigilance control device Vol 2 Issue 4 July 2013 405 ISSN 2278 621X International Journal of Latest Trends in Engineering and Technology IJLTET i Start gt Yes MU Motor Mode Rotates Mo Anyone of the loco inp wuts _ Tito Sta lt _ Iput rt Counit l 5s Co unter Yer Reset Start flashing LED for some Co
6. t is due to loco pilot 1 e engine driver or due to failure of locomotive By using this device we can also inform the action of the driver to the higher authorities if he fails to respond the cyclic warnings and the position of the train can also be tracked to avoid the accidents The high priority is given to the lives of people Hence this paper provides a feasible solution to reduce accidents due to human failure REFERENCES 1 2 3 4 5 6 7 ITSR Driver Safety Systems Discussion Paper 2006 Australia New South Wales Independent Transport Safety Regulator Sydney p 32 Santosh B Patil Rupal M Walli Design and Development of Fully Automatic AT89C52 Based Low Cost Embedded System For Rail Tracking International Journals of Electronics Communication and Soft Computing Science and Engineering IJECSCSE Vol 1 Issue 1 Pg 9 14 M A Mazidi The 8051 Microcontroller amp Embedded Systems Pearson Education Asia India 2 edition 2008 GSM User Manual SIMCOM LTD August 2006 http www atmel com http www simcom com Sky Traq Venus 6 GPS Module ST22 Data Sheet Vol 2 Issue 4 July 2013 407 ISSN 2278 621X
7. ted and the train slows down and comes to a stop Another form of driver safety system is Dead Man System which detects a continuous input from the driver e g by application of force to a pedal or handle 1 In this system there is no facility to inform the action of the driver and the position of the train to higher authorities to take any responsible decision So in order to overcome this disadvantage and to make the driver in alertness and to ensure safety to passengers the new system is proposed called modern vigilance control device The rest of the paper is organized as follows The proposed setup of the system 1 e the block diagram and its description are explained in section II Experimental results are presented in section III Concluding remarks are given in section IV Il PROPOSED SYSTEM A Block Diagram and its description The proposed system consists of different components interfacing to a microcontroller In this paper we are using AT89S52 microcontroller the heart of the system The AT89S52 microcontroller is a low power high performance CMOS 8 bit microcontroller with 8K bytes of in system programmable flash memory and it is a powerful Vol 2 Issue 4 July 2013 403 ISSN 2278 621X International Journal of Latest Trends in Engineering and Technology IJLTET microcontroller which provides a highly flexible and cost effective solution to many embedded control applications The block diagram is shown in Figure 1 Inp
8. unter duraton and increment counter Yes Imp ut start Burz ring forsome duration and increment counter Through GSM message to guard and signal inspector biz Imp ut Brake Mao Penalty Brake Through GSM message to signal inspector Position Tracking Through GSM message to signal inspector stop Figure 3 Flow chart of the System II EXPERIMENTAL RESULT This paper gives a different way of approaching the problem The proposed system not only alert the loco pilot but also informs the position of the pilot and also the train where it was stopped by using GSM and GPS technologies By using the flow chart in figure 2 the source code is developed The source code is written in embedded C language and is tested on Proteus 7 2 platform The hardware implementation of the modern vigilance control device is shown in figure 3 Vol 2 Issue 4 July 2013 406 ISSN 2278 621X International Journal of Latest Trends in Engineering and Technology IJLTET Figure 4 Hardware Implementation of modern vigilance control device IV CONCLUSION Many people travel in trains and the number of people travelling is more when compared to any other like cars buses etc In this paper the modern vigilance control device improves vigilance and provides warning and brake application signals in a predefined manner So with the use of this device we can ensure safety to passengers With this device we can analyze that whether the acciden
9. uts from loco pilot 1 Brake 2 Horn 3 Notch AV 4 NotchBV 5 Reset Lh Vv To mobile of Guard and Vigilance Officer Figure 1 Block Diagram The input power is step down to 5v DC from 230v AC power line by the power supply unit LCD Liquid Crystal Display screen is an electronic display module and find a wide range of applications The JHD 16x2A LCD is used and is connected to the output port of micro controller to display the cyclic operations of vigilance control device The microcontroller can communicate with the serial devices using its single serial port The logic levels at which this serial port operates is TTL logics But some of the serial devices operate at RS 232 logic levels So in order to communicate the microcontroller with modem a mismatch between the logic levels occurs In order to avoid this mismatch in other words to match the Logic levels a serial driver is used A MAX232 is a serial line driver used to establish communication between modem and microcontroller A GSM modem is a wireless modem that works with a GSM wireless network It operates at either the 900MHz or 1800MHz frequency band It supports voice calls and data transfer speeds of up to 9 6kbits s together with the transmission of SMS Short Message Service The GSM prototype is shown in Figure 2 a The GSM Modem comes with a serial interface which the modem can be controlled using AT command interface Here a GSM modem SIMCOM made SIM300 V 7 03
Download Pdf Manuals
Related Search