Zodiac Clearwater MicrOzone 300
Contents
1. If after the product and or part is returned prepaid and evaluated by CWT it proves to be defective while under warranty CWT will at its election either repair or replace the defective product and or part and will return ship at lowest cost transportation prepaid to you except for shipments going outside the 50 states of the United States of America If upon inspection it is determined that there is no defect or that the damage to the product and or part resulted from causes not within the scope of this limited warranty then you must bear the cost of repair or replacement of damaged product and or part and all return freight charges Any unauthorized attempt by the end user to repair CWT manufactured products without prior permission shall void any and all warranties For service contact your authorized dealer or distributor or CWT direct at 805 549 9724 extension 23 EXCLUSIVE WARRANTY There is no other expressed warranty on CWT products and or parts Neither this warranty or any other warranty expressed or implied including any implied warranties or merchantability of fitness shall extend beyond the warranty period Some states do not allow limitations on how long an implied warranty lasts so that the above limitation or exclusion may not apply to you DISCLAIMER OF INCIDENTAL AND CONSEQUENTIAL DAMAGES No responsibility is assumed for any incidental or consequential damages this includes any damage to another product or products r2. Hartford Loop see Figure 3 Determine orientation of the check valve by blowing through it flow should be directed to the point of use Step 5 Attach the opposite end of the tubing to the barbed fitting of the diffuser stone provided Step 6 Plug the Microzone 300 into a suitable outlet If the OAS7 is being used the Microzone 300 may be plugged into its switched outlet provided Note All equipment wiring and grounding must comply with all local electrical codes Figure 2 Shown OAS7 with CD300 ozone generator Air Flow Microzone 300 Air Prep Outlet p Flow j Check Valve Switched es Power Diffuser Stone Main Power Note OAS7 maximum head pressure 6 feet
3. Microzone 300 Corona Discharge Ozone Generator Owner s Manual ClearWater Tech LLC Integrated Ozone Systems 850 E Capitolio Way San Luis Obispo Ca 93401 805 549 9724 Fax 805 549 0306 E mail service cwtozone com www cwtozone com Copyright 2003 ClearWater Tech LLC Reproduction of any kind is prohibited Rev 01 03 ASSESSORIES de gt x Check Valve Diffuser Stone Parts Bag 2 screws 8 Clear Hose 2 hose clamps OZONE GENERATOR FRONT VIEW BOTTOM VIEW TOP VIEW Power Light Ozone Outlet Air Prep A Se Inlet hs Ground Lug Variable a Power Cord Off On Switch SAFETY WARNINGS e Read and follow all instructions e Save these Instructions e Before attempting any electrical connections be sure all power is off at the main circuit breaker e Install all electrical equipment at least five feet from any open body of water using non metalic plumbing e Install check valves and a Hartford Loop to prevent water from contacting the electrical equipment e Be sure to bond ground the system using the copper bonding lug on the bottom of the ozone generator The system should be bonded with solid copper wire conforming with all local state and national electrical codes Two aspects of ClearWater Tech ozone generators represent potential dangers ozone gas and high voltage electricity OZONE GAS WARNING Low concentrations of ozone can cause irritatio
4. ed serial number has been removed or which has been damaged or rendered defective as a result of An accident misuse alteration or abuse An act of God such as flood earthquake hurricane lightning or other disaster resulting only from the forces of nature Normal wear and tear Operation outside the usage parameters stated in the product user s manual Use of parts not sold by CWT Service or unit modification not authorized by CWT Failure to meet service requirements as outlined in the amp O manual Check valve solenoid valve failure Damage which may occur during shipping OBTAINING SERVICE UNDER THE WARRANTY Any product and or part not performing satisfactorily may be returned to CWT for evaluation A Return Goods Authorization RGA number must first be obtained by either calling or writing your local authorized dealer distributor or CWT direct prior to shipping the product The problem experienced with the product and or part must be clearly described The RGA number must appear prominently on the exterior of the shipped box es The product and or part must be packaged either in its original packing material or in comparable and suitable packing material if the original is not available You are responsible for paying shipping charges to CWT and for any damages to the product and or part that may occur during shipment It is recommended that you insure the shipment for the amount you originally paid for the product and or part
5. ee Figure 3 Determine orientation of the check valve by blowing through it flow should be directed to the point of use Step 4 Attach the other end of the tubing to the injection port and secure with the hose clamp provided Step 5 Plug the Microzone 300 into a suitable outlet If the PRO Series system is being used the Microzone 300 may be plugged into its switched outlet provided Note All equipment wiring and grounding must comply with all local electrical codes Figure 1 Shown PRO10 with CD300 ozone generator Microzone 300 Switched Power w a ee hee l Main Power Air Flow Water Flow m 2 Check Valve i er Flon Injector Port Water Flow DIFFUSION METHOD INSTALLATION Step 1 Mount the Microzone 300 ozone generator to a suitable flat surface using the two self tapping screws provided Note The distance from the Microzone 300 to point of diffusion should be no more than 8 feet Step 2 Cut a suitable length of the supplied tubing attach one end to the air prep outlet of the pressurized source used Attach the other end to the air inlet port of the Microzone 300 and secure with a hose clamp provided Step 3 Attach one end of the supplied tubing to the ozone outlet port of the Microzone 300 and secure with the hose clamp provided Step 4 Coil the tubing to create a Hartford Loop above the water line Insert the check valve provided at the highest point of the
6. esulting from such a defect Some states do not allow the exclusion or limitation of incidental or consequential damages so that above limitation or exclusion may not apply to you LEGAL REMEDIES OF PURCHASER This warranty gives you specific legal rights and you may also have other rights which vary from state to state THIS STATEMENT OF WARRANTY SUPERSEDES ALL OTHERS PROVIDED TO YOU AT ANY PRIOR TIME 6 Figure 3 Shown Hartford Loop Waterline i Min of three i 1 j 12 loops i Harford Loop I 1 To point of use UNPACKING Compare the ozone system equipment to packing list provided Before beginning any installation procedures thoroughly inspect all components for damage If damage is noticed promptly notify the freight carrier and request an on site inspection Inspect all packing materials for small parts before discarding EQUIPMENT PLACEMENT e When placing ozone system components make sure to consider safety maintenance requirements local building and fire codes From ozone generator NOTE The top of the Hartford loop and the check valve must be mounted above the water line START UP The CD300 ozone generator is equipped with a 0 to 100 variable OFF ON switch Depending on the amount of ozone required you may adjust the ozone output control switch counter clockwise for minimum output or off and clock wise for maximum output The ozone generator is equipped with a
7. h has developed the PRO Series System with magnetic drive pump programmable timer and venturi to provide a suitable suction port for the injection method see Figure 1 For typical spa applica tions the spa manufacture has provided an ozone ready suction port which eliminates the need for additional equipment see spa manual for installation The diffusion method requires a pressurized air source which feeds air through the ozone generator and out to an atmospheric body of water A diffuser stone provided with the Microzone 300 is used for increased mixing of ozone in solution For this application ClearWater Tech has developed the OAS7 compressor with program mable timer to provide the pressure required see Figure 2 Note Regardless of application water back flow prevention devices such as a check valve and Hartford Loop should be implemented with the use of the Microzone 300 see figure 3 INJECTION METHOD INSTALLATION Step 1 Mount the Microzone 300 ozone generator to a suitable flat surface using the two self tapping screws provided Note The distance from the Microzone 300 to the injection port should be no more than 8 feet Step 2 Attach one end of the supplied tubing to the ozone outlet port of the Microzone 300 and secure with a hose clamp provided Step 3 Coil the tubing to create a Hartford Loop above the water line Insert the check valve provided at the highest point of the Hartford Loop s
8. main power indicating light next to the variable switch This light will be illuminated when the switch is not in the off position The ozone generator will not produce ozone until airflow is initiated To determine the most favorable placement the following should be considered e Located downstream of all other existing water system components e Located upstream of the residual sanitizer injection point if so equipped e The pH adjustment chemical injection point should be located downstream of the residual sanitizer injection point if so equipped e Location of ozone generator should be no more than 8 feet from point of use e Adequate protection from weather dust and excessive heat Ambient temperature range 20 F to 85 F continuous Note Equipment installed in extreme environmental conditions will void manufacturers warranty THEORY OF OPERATION PRODUCT DESCRIPTION MAINTENANCE Disconect power from unit before any maintenance procedures e Check valve replace diaphragm check valve annually e Reaction chamber replace the reaction chamber every 3 years SPECIFICATIONS e Electrical 120VAC 60Hz 0 2a 220VAC 50Hz 0 1a e Dimensions 6 1 4 X 5 1 4 X 2 e Weight 1 9 pounds The Microzone 300 ozone generator may be used to inject or diffuse ozone into water The injection method requires a venturi injector to draw the ozone from the ozone generator and into the water line ClearWater Tec
9. n to the eyes throat and respiratory system HIGH VOLTAGE WARNING ClearWater Tech ozone generators operate at high voltages If contact is made with operating high voltage components electric shock will occur ClearWater Tech LLC Limited One Year Warranty SUMMARY OF THE WARRANTY ClearWater Tech LLC CWT makes every effort to assure that its products meet high quality and durability standards and warrants the products it manufactures against defects in materials and workmanship for a period of one 1 year commencing on the date of original shipment from CWT with the following exceptions 1 The warranty period shall begin on the installation date if the installation is performed within 90 days of the original shipment from CWT 2 The warranty period shall begin on the date of the bill of sale to the end user if the installation date is more 90 days after the original shipment date To validate the warranty a warranty card must be returned to CWT and must include the following information End user name Complete address including telephone number Date installed Complete model and serial number information Name of company from which the unit was purchased Repairs and replacement parts provided under this warranty shall carry only the unexpired portion of this warranty or 90 days whichever is longer ITEMS EXCLUDED FROM THE WARRANTY This warranty does not extend to any product and or part from which the factory assign
Download Pdf Manuals
Related Search