Self educting no zzle
Contents
1. Presentofion e Overall dimensions Exploded view e Bill of moteriolsS Worning e User mMonvol eMointenonce Please read this manual before using the equipment POK SA ZI Les Guignons 10400 Nogent sur Seine FRANCE Tel 03 25 39 84 78 Fax 03 25 39 84 90 Email info pok fr Site Web www pok fr Rev C 04 04 13 The technical informations included in this document might change without any warning Contact our sales service for further details Doc 1838 EN Presentofion Mark Description _ 6 Wheel for jet selection Characteristics petals O e Body in aluminium alloy Consmiacion e Red and yellow polyester painted e Harcoat anodized aluminium e Screws in stainless steel Inlet e Nozzle Male thread 2 5 e Eductor Storz DN38 coupling e 2000 l min 530 GPM or Flow rate e 3000 l min 800 GPM Note Only one of those flow rates applies it depends on your order Configuration made in factory only further modification are impossible Working pressure 7 bar 100 PSI 16 bar 230 PSI e Straight Jet e Attack 30 e Spray 110 3 or 6 7 bar 100 PSI Suction Note Suction percentage depends on the metering disk which can be changed easily if necessary Other percentage available on demand e Optimal performances 3m Suction hose max length Note Over 3m suction may not operate properly e Suction pipe supplied Note Usually 3m may depends on the order Accessorie2. e Connect your nozzle on a monitor make sure it is properly connected and that no parts are missing or damaged e Make sure the monitor stand will resist to the reaction force of the nozzle e Connect the suction pipe on the nozzle and put the tube in the foam tank e When you re sure that the installation is meeting all the security requirements you can put the nozzle under pressure e Meanwhile the equipment is under pressure please respects the following points e Do not target someone e Do not use a vertical angle under 35 or over 90 e Do not target a point in the same direction than your pump your stand may not resist and cause important damages because of reaction force e Rotate the jet adjustment ring to change the jet type e Straight e Attack 30 e Spray 110 Do not use the spray if equipment around the nozzle would not resist to important water projection e Range 7bar 100 PSI e Model 2000 l min Water 50m Foam 40m e Model 3000 min Water 55m Foam 45m The ranges may vary depending on your installation and wheather conditions 3 Limits of use e If no suction pipe is connected water may go out if you use the equipment at a very low pressure e If the equipment is working with a suction pipe connected but not to a foam tank be careful where you put the tube it will draw in small particles around it e If you use the nozzle to make foam make sure you do not have a flow rate under 15
3. 39 84 78 Fax 03 25 39 84 90 Email info pok fr Site Web www pok fr 4 Rev C 04 04 13 The technical informations included in this document might change without any warning Contact our sales service for further details Doc 1838 EN Warning Precaution of use This nozzle is made to work with a maximum flow rate of 2000 l min 530 GPM or 3000 l min 800 GPM and an advised presure of 7 bar 100 PSI Equipment efficiency is not certain over those values The maximum working pressure is 16 bar reliability is not certain over this value Only the staff trained on the equipment and aware of the security rules is allowed to use or do maintenance on the monitor It is important to make sure the monitor is properly attached on its stand and that the stand will resist to the reaction force in case of mobile monitor make sure the supplied belt is strongly fixed to an anchor point Ignoring this may cause important damage or be deadly Reaction force about 130 Kgs for 2000 I min 7 bar and about 200 Kgs for 3000 l min 7 bar at the nozzle outlet Never face the jet or target someone consequences may be deadly Please note that using the monitor may cause important damage in the area where the jet is falling make sure the area is secured before use Disassembly and warranty Excepted special agreement the warranty is valid for 1 year The bill of materials and exploded view included in this document are no
4. 00 l min 400 GPM it may not work properly under this value e For best hydraulic performances do not use the nozzle over the value quoted below e Flow rate 2000 LPM 530 GPM or 3000 LPM 800 GPM depends on you model e Pressure advised 7 bar 100 PSI e Please use only the suction pipe supplied with the nozzle POK SA ZI Les Guignons 10400 Nogent sur Seine FRANCE Tel 03 25 39 84 78 Fax 03 25 39 84 90 Email info pok fr Site Web www pok fr 6 Rev C 04 04 13 The technical informations included in this document might change without any warning Contact our sales service for further details Doc 1838 EN Moaintenonce 1 Cleaning After each use please do the following operations e Let the nozzle work with clear water e Connect the suction pipe and put the tube into clear water to draw water in in order to clean it up e Clean the nozzle outer faces with clear water but without high pressure jet e Store the equipment in a dry place e Make sure no parts are missing or damaged It is important to do these operations to maintain the product working well emulsifying agent are corrosive products and letting particles inside may damage gaskets at short term 2 Spare parts Parts as gaskets may need to be changed more or less often depending on storage and use conditions Please contact our sales service in order to be informed on tariffs and conditions for returns or to obtain spare par
5. s e Suction valve option POK SA ZI Les Guignons 10400 Nogent sur Seine FRANCE Tel 03 25 39 84 78 Fax 03 25 39 84 90 Email info pok fr Site Web www pok fr Rev C 04 04 13 The technical informations included in this document might change without any warning Contact our sales service for further details Doc 1838 EN Overoll dimensions 315 Spray jet 339 Straight jet P78 Storz DN38 R116 Weight 5 5 Kg Rev C 04 04 13 dSd c bic Wa POK SA ZI Les Guignons 10400 Nogent sur Seine FRANCE Tel 03 25 39 84 78 Fax 03 25 39 84 90 Email info pok fr Site Web www pok fr O Doc 1838 EN The technical informations included in this document might change without any warning Contact our sales service for further details Exploded view POK SA ZI Les Guignons 10400 Nogent sur Seine FRANCE Tel 03 25 39 84 78 Fax 03 25 39 84 90 Email info pok fr Site Web www pok fr Rev C 04 04 13 The technical informations included in this document might change without any warning Contact our sales service for further details Doc 1838 EN Poxi Bill of moteriols Ne Qty Description Ref 1 1 Body Gasket R16 S Converter 4a Gasket R43 Bore Screw STHC TR M5 5 7 Gasket R42 gs 1 Head ring 9 1 Bumperguard gt o Ball vlave FM 1 1 4 BSP FM 1 1 4 BSP 7 POK SA ZI Les Guignons 10400 Nogent sur Seine FRANCE Tel 03 25
6. t a disassembly guide Dismantling the equipment outside POK factory cancel the warranty Do not modify the equipment it may no longer work properly or be dangerous at use Only POK SA can repair and guarantee the equipment working well and without danger If parts are changed outside POK factory you must make carry out the service procedure to make sure everything is working well POK SA can t be responsible for any damage caused following a disassembly outside its factory modification or bad use of the equipment POK SA ZI Les Guignons 10400 Nogent sur Seine FRANCE Tel 03 25 39 84 78 Fax 03 25 39 84 90 Email info pok fr Site Web www pok fr 5 Rev C 04 04 13 The technical informations included in this document might change without any warning Contact our sales service for further details Doc 1838 EN User manual 1 Introduction This nozzle is made to work with a flow rate of 2000 l min 530GPM or 3000 l min 800 GPM depending on your order This flow rate is given for a pressure of 7 bar 100 PSI A storz DN38 coupling is put on the nozzle in order to connect a suction pipe supplied A metering disk is present between the body and the storz coupling it calibrates the percentage of suction usually 3 or 6 but it may vary depending on your order The metering disk can be replaced by removing the Storz coupling DN38 Be careful to put again the gaskets properly 2 Installation amp use
7. ts Use the bill of materials in this document to identify the parts to change 3 Put back into service procedure If you change parts by your own please do these steps in order to make sure the equipment is working well Those points won t make you recover the warranty or make POK responsible for further accident e Make sure no parts are missing or damaged e Make sure all parts move properly without problems e Connect the nozzle on your monitor e Put everything under pressure following the installation amp use guide e Use low pressure at the beginning then increase to 12 bar 175 PSI slowly During this step make Sure there is no leaking Let everything move e Connect the suction pipe and use the nozzle normally Make sure it draws in water or foam e If no problems are detected you can put back the equipment into service POK SA ZI Les Guignons 10400 Nogent sur Seine FRANCE Tel 03 25 39 84 78 Fax 03 25 39 84 90 Email info pok fr Site Web www pok fr Rev C 04 04 13 The technical informations included in this document might change without any warning Contact our sales service for further details Doc 1838 EN
Download Pdf Manuals
Related Search