Operating Instructions
Contents
1. COLOUR STORM TRI Order code LEDJ165 USER MANUAL Colour Storm Tri Safety WARNING FOR YOUR OWN SAFETY PLEASE READ THIS USER MANUAL CAREFULLY BEFORE YOUR INITIAL START UP CAUTION Keep this equipment away from rain moisture and liquids SAFETY INSTRUCTIONS Every person involved with the installation operation amp maintenance of this equipment should Be competent Follow the instructions of this manual CAUTION TAKE CARE USING THIS EQUIPMENT HIGH VOLTAGE RISK OF ELECTRIC SHOCK Before your initial start up please make sure that there is no damage caused during transportation Should there be any consult your dealer and do not use the equipment To maintain the equipment in good working condition and to ensure safe operation it is necessary for the user to follow the safety instructions and warning notes written in this manual Please note that damages caused by user modifications to this equipment are not subject to warranty Colour Storm Tri Safety IMPORTANT The manufacturer will not accept liability for any resulting damages caused by the non observance of this manual or any unauthorised modification to the equipment e Never let the power cable come into contact with other cables Handle the power cable and all mains voltage connections with particular caution e Never remove warning or informative labels from the equipment Do not open the equipment and do not modi2. Now on the master unit press the MODE button to select the desired mode and the slave units will now run in sequence with the master unit Built in programmes To activate the units built in programmes press the MODE button to show 01 STATIC on the LCD screen Press the ENTER button to choose between the 14 built in programmes by using the UP and DOWN buttons Now press the ENTER button to select the desired speed and adjust by using the UP and DOWN buttons Press the ENTER button once more to select the desired flash value and adjust by using the UP and DOWN buttons Speed values 00 99 00 slow 99 fast Flash values 00 99 00 slow 99 fast For the 14 built in programmes please see page 5 DMX mode To activate the unit in DMX mode press the MODE button to show DMX MODE on the LCD screen Press the ENTER button and select the desired DMX address setting by using the UP and DOWN buttons Then to select one of the 10 DMX modes 51 48 27 24 15 12 9 6 5 or 3 channel press the ENTER button again to choose the desired DMX mode by using the UP and DOWN buttons For the 51 48 27 24 15 12 9 6 5 or 3 channel DMX address information please see pages 6 7 and 8 NOTE Once the desired settings have been selected in each of the above modes ALWAYS confirm the settings by pressing the ENTER butt
3. Locking 3 5 pin XLR female socket do AA DMX 512 USITT e DMX channels 51 48 27 24 15 12 9 6 5 amp 3
4. please ensure that the Colour Storm Tri has been set into SLAVE MODE and connect the controller to the 3 pin XLR socket on the rear of the unit The HBR 1D can be used in conjunction with the MB 2 Footswitch LEDJ124 by plugging the 5 pin XLR from the MB 2 into the HBR 1D controller Note please follow the user manuals supplied with the optional MB 2 and HBR 1D control lers for details of various operation modes Colour Storm Tri Operation Modes Operation modes Sound Active mode To activate the unit in sound active mode press the MODE button to show SOUND MODE on the LCD screen Now press the ENTER button to select the desired sensitivity level by using the UP and DOWN buttons Press the ENTER button again to select the frequency level and adjust by using the UP and DOWN buttons SENS 00 31 00 low 31 high FQN 01 99 01 low 99 high Auto run mode To activate the unit in auto run mode press the MODE button to show AUTO RUN on the LCD screen Now press the ENTER button to select the desired frequency level by using the UP and DOWN buttons FQN 01 99 01 low 99 high Note In this mode it will run 13 built in programmes in a continuous loop Slave mode To activate the unit in slave mode first you must link multiple units together and press the MODE button to show SLAVE MODE on the LCD screen
5. 29 CH30 CH31 CH32 CH33 CH34 CH35 ES CH37 CH38 CH39 CH40 CH41 CH42 CH43 CH44 CH45 CH46 CH47 CH28 _ 51 channel mode DMX chart EE CH10 CH11 CH12 CH13 CH14 CH15 Master Flash 0 21 Dimmer 0 255 R1 G1 B1 R2 G2 B4 0 255 CH16 CH17 CH18 CH19 CH20 CH21 CH22 CH23 CH24 CH25 CH26 CH27 CH28 CH29 CH30 CH31 CH32 CH33 CH34 CH35 CH36 CH37 CH38 CH39 CH40 CH41 CH42 CH43 CH44 CH45 CH46 CH47 CH48 CH49 CH50 CH51 Colour Storm Tri DMX Set up DMX 512 e DMX Digital Multiplex is a universal protocol used as a form of communication between intelligent fixtures and controllers A DMX controller sends DMX data instructions form the controller to the fixture DMX data is sent as serial data that travels from fixture to fixture via the DATA IN and DATA OUT XLR terminals located on all DMX fixtures most controllers only have a data out terminal DMX Linking e DMX is a language allowing all makes and models of different manufactures to be linked together and operate from a single controller as long as all fixtures and the controller are DMX compliant To ensure proper DMX data transmission when using several DMX fixtures try to use the shortest cable path possible The order in which fixtures are connected in a DMX line does not influence the DMX addressing For example a fixture assigned to a DMX ad
6. ckout R Red RG Yellow G Green 1 BLA RGB 2 BLA RGB GB Cyan B Blue BR Purple RGB White Colour Storm Tri DMX Programme Charts 3 channel mode DMX chart All All Red Blue 0 100 0 100 5 channel mode DMX chart po poo on 6 channel mode DMX chart G1 B1 R2 G2 B2 0 255 0 255 0 255 0 255 0 255 33 43 Yellow 44 54 Green 55 65 Cyan 66 76 Blue 77 87 Purple 88 98 White 99 109 Dream 110 120 Meteor 121 131 Fade 132 142 Change 143 153 Flow 1 154 164 Flow 2 165 175 F 176 186 F 187 197 Flow 5 198 208 Flow 6 209 219 Flow 7 X l 220 230 Flow 8 Colour Colour Select Select 231 241 Flow 9 Colour Colour Select Select Colour Storm Tri DMX Programme Charts Note For 15 27 and 51 channel modes please follow the 9 channel DMX chart for channels 1 2 and 3 12 channel mode DMX chart 15 channel mode DMX chart CH2 CH3 CH4 CH5 CH6 CH7 CH8 CH9 CH10 CH11 CH12 CH13 CH14 CH15 24 channel mode DMX chart CH13 CH14 CH15 CH16 CH17 CH18 CH19 CH20 CH21 CH22 CH23 CH24 27 channel mode DMX chart Master Flash 0 21 Dimmer 0 255 R1 G1 B1 R2 G2 B2 R3 G3 B3 R4 G4 B4 0 255 CH16 CH17 CH18 CH19 CH20 CH21 CH22 CH23 CH24 CH25 CH26 CH27 Colour Storm Tri DMX Programme Charts 48 channel mode DMX chart oma CH14 CH15 CH16 CH17 CH18 CH19 CH20 CH21 CH22 CH23 EI CH26 CH27 CH28 CH
7. dress of 1 may be placed anywhere in a DMX line at the beginning at the end or anywhere in the middle When a fixture is assigned a DMX address of 1 the DMX controller knows to send DATA assigned to address 1 to that unit no matter where it is located in the DMX chain DATA Cable DMX cable requirements for DMX operation Colour Storm Tri can be controlled via DMX 512 protocol The DMX address is set on the back of the unit Your unit and your DMX controller require a standard 3 or 5 pin XLR connector for data input output figure 1 Figure 1 Further DMX cables can be purchased from all good sound and lighting suppliers or Prolight dealers Please quote CABL10 2M CABL11 5M CABL12 10M Also remember that DMX cable must be daisy chained and cannot be split Colour Storm Tri DMX Set up Notice Be sure to follow figures 2 amp 3 when making your own cables Do not connect the cable s shield conductor to the ground lug or allow the shield conductor to come in contact with the XLR s outer casing Grounding the shield could cause a short circuit and erratic behaviour common DMX 512 out 3 pin XLR DMX 512 in 3 pin XLR XLR MALE SOCKET XLR FEMALE SOCKET XLR Pin Configuration 2 cold 1 ground 1 ground 2 cold Pin 1 Ground Pin 2 Negative FIGURE 3 FIGURE 2 Special Note Line termination e When longer runs of cable are used you may need to use a terminator on the la
8. f purchase OPERATING DETERMINATIONS If this equipment is operated in any other way than those described in this manual the product may suffer damage and the warranty becomes void Incorrect operation may lead to danger e g short circuit burns electric shocks lamp failure etc Do not endanger your own safety and the safety of others Incorrect installation or use can cause serious damage to people and property Colour Storm Tri Introduction Introduction Features 16 x 3W tri colour LEDs e Beam angle 25 degrees 400Hz Refresh rate 0 100 dimming and variable strobe e DMX channels 3 5 6 9 12 15 24 27 48 or 51 selectable e Sound active auto master slave and DMX modes 4 push button menu with LCD display Powercon in out sockets 3 Pin XLR in out sockets e 5 pin XLR in out sockets Overview DMX Hanging in bracket LCD Display l COLOUR STORM T b _ 0 060 O O PMXOUT D www prolight co uk o z DODO S 1 Mode Enter button button Up button Down Power button Power in out Setup Operating Instructions The Colour Storm Tri is a DMX 512 controllable unit made up of high efficiency tri colour LEDs and will operate in auto master slave sound activated or DMX control modes HBR 1D Operation optional To operate the Colour Strom Tri via the optional LEDJ HBR 1D controller LEDJ123
9. fy the equipment e Do not connect this equipment to a dimmer pack e Do not switch the equipment on and off in short intervals as this will reduce the system s life Only use the equipment indoors Do not expose to flammable sources liquids or gases e Always disconnect the power from the mains when equipment is not in use or before cleaning Only handle the power cable by the plug Never pull out the plug by pulling the power cable Make sure that the available voltage is between 220v 240v e Make sure that the power cable is never crimped or damaged Check the equipment and the power cable periodically If the equipment is dropped or damaged disconnect the mains power supply immediately Have a qualified engineer inspect the equipment before operating again If the equipment has been exposed to drastic temperature fluctuation e g after transportation do not switch it on immediately The arising condensation might damage the equipment Leave the equipment switched off until it has reached room temperature If your product fails to function correctly discontinue use immediately Pack the unit securely preferably in the original packing material and return it to your Prolight dealer for service Only use fuses of same type and rating Repairs servicing and power connection must only be carried out by a qualified technician THIS UNIT CONTAINS NO USER SERVICEABLE PARTS e WARRANTY One year from date o
10. on 4 Colour Storm Tri Built in Programme Chart Invert mode To activate the Invert function press the MODE button to show FLOW INVERT on the LCD screen Press the ENTER button to turn the function ON or OFF by using the UP and DOWN buttons 14 Built in programme chart BLA Blackout R Red RG Yellow G Green STATIC COLOR GB Cyan B Blue BR Purple RGB White BLACKOUT RGB Flash speed adjustable Flash00 99 Speed 00 99 Flash 00 99 Speed 8 Flash adjustable Speed 00 99 Flash 00 99 Speed amp Flash adjustable Speed 00 99 Flash 00 99 Speed amp Flash adjustable Speed 00 99 Flash 00 99 Speed amp Flash adjustable Seven colour chase forward Speed 00 99 Flash 00 99 Speed amp Flash adjustable Seven colour chase forward amp reverse Speed 00 99 Flash 00 99 Speed amp Flash adjustable Speed 00 99 Flash 00 99 Speed amp Flash adjustable Seven colour fade chase in relay pattern forward amp Speed 00 99 Flash 00 99 reverse Speed amp Flash adjustable Speed 00 99 Flash 00 99 Speed amp Flash adjustable Speed 00 99 Flash 00 99 Speed amp Flash adjustable 99 Fl Speed 00 99 Flash 00 99 Speed amp Flash adjustable FLOW 8 Two colour chase forward Speed 00 99 Flash 00 99 Speed amp Flash adjustable 1 BLA RGB 2 BLA RGB Blackout Red Yellow Green Cyan Blue Purple White Two colour chase forward amp reverse FLOW 9 Speed amp Flash adjustable Speed00 99 Flash 00 99 BLA Bla
11. st unit to avoid erratic behaviour Termination reduces signal transmission problems O and interferance it is always advisable to connect a DMX terminal resistance 120 Ohm 1 4 W between pin 2 DMX and pin 3 DMX of the last fixture Using a cable terminator part number 1 90 will decrease the possibilities of erratic behaviour 5 Pin XLR DMX Connectors e Some manufactures use 5 pin XLR connectors for data transmission in place of 3 pin 5 Pin XLR fixtures may be implemented in a 3 pin XLR DMX line When inserting standard 5 pin XLR connectors in to a 3 pin line a cable adaptor must be used The chart below details the correct cable conversion 5 ALR socket 1 sereen A 3 Pin XLR socket Pin 2 Signal Pin 1 GND screen Pin 3 Signal 2 Pin 2 Signal in 4 Pin 3 Signal Pin 5 N C 3 Pin ALR socket Pin 1 GNI screen Pin 2 Signal 2 Pin 3 Signal 10 Colour Storm Tri Technical Specifications Technical Specifications Weight amp Dimensions Length AAA 1050mm SWIAT e uuu us 90mm s H ight u 198mm Weight uuu diivanid itta aeta 7 3Kgs Power A A 240V 50hz e Power consumption 99W Fuse 2 Control amp Programming Data AA Locking 3 5 pin XLR male socket e Data output
Download Pdf Manuals
Related Search