Rebound Bouncer Manual
Contents
1. Your equipment Check all equipment prior to use Inspect your Rebound for missing defective or worn parts Never use the product if excessive wear or damage are detected Always check for proper inflation before each use Temperature and environ mental changes can cause changes in tube pressure Using the product over or under inflated is dangerous and can cause damage to the product voiding the warranty Always check security of the anchor and all attachments before each use Always wear a floatation vest PFD as required by the authorities in the area of use THE WARNINGS AND PRACTICES SET FORTH ABOVE IN THE WATERSPORTS SAFETY CODE REPRESENT SOME COMMON RISKS ENCOUNTERED BY USERS THE CODE DOES NOT PURPORT TO COVER ALL INSTANCES OF RISK OR DANGER PLEASE USE COMMON SENSE AND GOOD JUDGMENT Please contact us if you have any questions on the proper selection function or safe use of this product Assembly 1 Locate a flat dry area with access to electrical outlet or extension cord 2 Unroll and place the Rebound Bouncer on the ground and locate the valve as shown in Fig 1 Remove valve cover and push valve plunger in Twist the valve stem 90 degrees to open or close the 1 Way valve feature 3 Using a high output inflator deflator place the inflation hose with proper adap tor into the valve Inflate to 1 2 psi 0 083 bar where tube is firm and tight Check for proper air pressure using a manomete2. Aqua PLAT Z l Po sa a Stop Read this manual carefully before using this product Manual Covers The Max Max Following Products Jumpers Users Max Weight Rebound 12 One 1 Rebound Aquapark Set 12 One 1 ree Three 3 600 Ibs 272 kg Three 3 600 Ibs 272 kg Ive 9 1000 Ibs 454 kg Five 5 1000 Ibs 454 kg Seven 7 1200 Ibs 544 kg Rebound 16 Rebound Aquapark Set 16 Three 3 Rebound 20 Three 3 Contents Per Product No Special Tools Required To Assemble Your New Rebound Bouncers Rebound Bouncer 12 1 Rebound Tube 1 SwimStep Access Plat form 2 Interloc Straps 1 Repair Kit Rebound Aquapark Set 12 1 Rebound Tube 1 Rebound Slide 1 i Log 1 SwimStep Access Platform 6 Interloc Straps 1 Repair Kit Rebound Bouncer 16 1 Rebound Tube 1 SwimStep Access Plat form 2 Interloc Straps 1 4 Way Mooring Bridle 1 Repair Kit Rebound Aquapark Set 16 1 Rebound Tube 1 Rebound Slide 1 i Log 1 SwimStep Platform 1 4 Way Bridle 6 Interloc Straps 1 Repair Kit Rebound 20 1 Rebound Tube 1 SwimStep Platform 1 4 Way Bridle 1 Repair Kit Watersports Safety Code Watersports are fun and challenging but involve inherent risks of injury or death To increase your enjoyment of the sport and to reduce your risks use common sense and follow the
3. be used to help protect this product against marine growth DAMAGE CAUSED BY EXPOSURE TO SALT WATER IS NOT COVERED BY WARRANTY Aquaglide Inc 1 North Shore Dr SE White Salmon WA 98672 Compliant with DIN EN 15649 Aqua ie PLAT Peformance AQUAGLIDE INC WHITE SALMON WA U S A STANDARDS EN 15649 2012 W A S 0 083bar PRODUCT REBOUND 20 1 2psi MADE IN PR C DESIGNED IN U S A No protection against drowning Keine Schutz gegen Ertrinken Pas de protection contre la noayada No protege contra el ahogamiento Nessuna protezione contro I affogamento Beschermt niet tegen verdrinken Only for swimmers Nur fur schwimmer Seulement pour les nageurs Solo para nadadores Solo per i nuotatori Alleen voor zwemmers 599 cm 236 599 cm 236 Rebound 20 H 98cm 387 L W SR 8 5 4A WARNING Prolonged exposure to salt water can damage and or shorten the expected lifetime of this product The marine environment includes many damaging elements including corrosion abrasion and damage from marine life such as barnacles Regular cleaning and rinsing with fresh water can reduce these risks A PVC safe antifouling paint should be used to help protect this product against marine growth DAMAGE CAUSED BY EXPOSURE TO SALT WATER IS NOT COVERED BY WARRANTY Aquaglide Inc 1 North Shore Dr SE White Salmon WA 98672 Compliant with DIN EN 15649 2012
4. for proper air pressure using a manometer It may appear to have lost air early in the morning but will expand once the sun warms it Maximum expansion will occur in the heat of the day Under inflation can cause excessive wear Proper inflation is important as this will discourage marine animals from chewing and prevent damage from wear Siorage 1 Before storing place the product on a clean level area Clean with mild soap and water and allow to dry completely Apply 303 Protectant to the surface of all tubes before deflating 2 Remove all attachments and store in a sealed water proof container i e a plastic covered box or bin 3 Remove ALL of the air from the tube using the deflation end of the high output inflator deflator 4 Fold the deflated tube in thirds then flat fold or roll loosely 5 Store the product out of direct sunlight and protected from the environment in a Clean dry location It is best to store inside a container with moth balls to prevent damage from rodents NEVER store uncovered in a damp location or on concrete surface NEVER store at temperatures below 40 degrees F Aquaglide Inc 1 North Shore Dr SE White Salmon WA 98672 Tel 01 509 493 4938 Fax 01 509 4934900 Wiww Aguaglide net Aqua o P L AT RG Li WORK SPAGE AND TOOLS 1 Take care to position yourself in a clean dry area with ea ventila tion For proper curing of adhesives temperature should remain above 10 C 50
5. inflated In hot weather be sure to leave room for air expansion or let air out if it becomes too hot DO NOT OVER FILL 3 Attach the Slide to the Rebound using the 4 Interloc straps as shown in the instructions to the right 4 Congratulations You are now ready to place your Rebound Aquapark in the water To launch your Rebound Aquapark Set make sure to have at least 3 4 people evenly spaced around the Aquapark to help carry it Use the molded transport handles Be sure to support the end of the i Log during transport When connecting multiple items use only Aquaglide Interloc straps and connecting rings according to the Interloc strap instructions provided Make sure that the connec tion is tight and that there is NO GAP greater than 25mm 3 4 between items IMPORTANT Failure to connect these items properly may result in injury or death the boarding platform through a single ring 1 D ring below Cinch until it is tight 2 Wwww Aquaglide net Interloc s Interloc Strap Assembly Instri Interloc Strap Assembly Instructions Interloc straps should already be attached to 1 Thread the end of the Interloc strap through the two D Rings on the Rebound then back 2 Pull all the webbing through the rings until the white arrow of the Interloc logo stops at the NEVER DRAG YOUR REBOUND SET YOU MUST LIFT AND SET TO AVOID ANY ACCIDENTAL TE
6. of 5cm x 5cm 2 x 2 for a pinhole leak The larger the better b Square patches with rounded corners are usually best as this reduces the risk of peeling 3 Dry fit the patch over the area to be repaired to ensure good fit and coverage 4 Use a clean 120 grit sand acid to rough up the surface to be patched AND ALSO the back of the patch material Aquaglide Inc 1 North Shore Dr SE White Salmon WA 98672 TEL 01 509 493 4938 FAX 01 509 493 4966 Repair Instructions 5 Use solvent MEK or Rubbing Alcohol and a fresh cloth to clean the sanded areas removing all debris 6 Dry fit the patch again and use china marker provided to carefully outline where the patch will be located 7 Next use the glue provided Use a disposable chip brush to spread glue if needed Try to work neatly and quickly a Using disposable brush apply a thin even a of glue to the repair area making sure to cover the area completely Stay INSIDE the china marker outline b Using disposable brush apply a thin even layer of glue to the to the back of the patch making sure to cover the area completely c Allow glue to cure for approximately 60 seconds d Starting at one corner carefully align the patch over the repair area using the china marker outline as a guide Once the 2 surfaces touch the bond will be immediate so take care e dun at one corner and working outward carefully apply the patch to the repair area us
7. this agreement and the North Sports Inc and Aquaglide Inc Owner s Manual Aquaglide Inc warrants products to be free by misuse abuse neglect or normal wear and rization number RA is given by Aquaglide in of defects in material or workmanship to the tear including but not limited to punctures advance The RA number must be on the outside original purchaser for a period of Three 3 dragging the product over the ground damage of the package or it will not be accepted at our years from date of purchase This warranty due to excessive sun exposure or seam failure warehouse Freight on the returned product must is subject to the following limitations due to overinflation in the sun damage caused by be prepaid or it will not be accepted Upon receipt improper dio E Al a caused Aquaglide will make a determination within 30 e vali g use in waves or shore break and damage caused days If the product is covered under warranty it me ML ee ok pur by anything other than defects in materials and will be returned to the customer at the expense of workmanship Aquaglide Inc after repairs can be made If not sui the customer will receive a quote for repair and So ne Ro 6 This warranty is voided if any unauthorized or replacement as well as any necessary cleaning repair change or modification has been made to and shipping charges The customer will have any part of the equipment Authorization for such 30 days to accept the quotation A
8. ARING ON SHARP OBJECTS Anchoring NOTE Take a moment to locate the anchoring rings underneath your Rebound Bouncer The Rebound 12 has 2 anchor rings on the underside of the tube Attach anchor line to at least 1 ring We suggest using 2 rings with a 2 way bridle not included for long term mooring The Rebound 16 amp 20 each have 4 rein forced anchor rings evenly spaced around the underside of the tube The Rebound 16 amp 20 each come with a 4 Way Mooring Bridle and stainless swivel attached Connect anchor chain to the lower portion of the stainless swivel IMPORTANT Proper anchoring is essential to the safety and performance of your product Due to the wide variety of conditions we advise using a professional skilled in mooring and anchoring and experienced with local condi tions If improperly anchored the product can move and or float away Aquaglide Inc is not responsible for any damage injuries or losses due to improper anchoring Here are some general guidelines for anchor ing your product These guidelines are not intended to replace the need for professional installation 1 Choose a location for your Rebound bouncer and or aquapark Place the product in at least 8 ft of water depth and in an area pro tected from the wind and boat traffic Review relevant rules and restrictions with your local authorities 2 Carefully check area under the bouncer and or aquapark for sharp or dang
9. F In most cases you will need enough room to inflate the product 2 Repair Kit Contents PVC Patch material PVC Glue Instructions 3 Additional items that MAY be needed Air pump Sharp scissors and or razor knife Dish washing liquid water small bowl or pal bottle 120 Grit sandpaper solvent such as MEK Methyl Ethy Ketone or Rubbing alcohol china marker small chip brush or disposable paint brush LOCATE LEAKIS 1 there is a problem with air leaks you will need to locate the leak s irst 2 Inflate cia uaglide Platinum product fully Some small leaks can close themselves at lower air pressures so it is best to maintain full pressure by re inflating periodically while checking for leaks 3 Use a soapy water solution 50 50 dish soap amp water and a cloth to check for leaks Work slowly around the product SM or swabbing on soapy water solution Look for growing bubbles which indicate a leak 4 ae leak is confirmed dry the area well mark it and prepare to patch PATCHING Reinforced PVC Patch with high grade adhesive IMPORTANT leaks must be patched with the item completely deflated and patches must be allowed to cure for 24 hours 1 DEFLATE your Aquaglide Platinum product completely 2 ae cut PVC patch material to size using sharp scissors or razor nife a Patch should be least 3 5cm 1 2 larger than hole IN ALL DIRECTIONS around any air leak This means a minimum patch size
10. MMON SENSE AND GOOD JUDGMENT Please contact the dealer or manufacturer of this product if you have any questions about proper selection function or safe use of this product x 3 Made in China Please Do Not Return This Product To The Store For questions regarding assembly parts or warranty contact our customer service department at 1 509 493 4938 or access product information at www aquaglide net Do not use in water where there are sharks or other animals that could pose a threat to humans If product is used indoors always ensure adequate ceiling height overhead Always remove personal items such as rings watches or other sharp objects before use www Aquaglide net Aqua ie PLAT Peformance AQUAGLIDE INC WHITE SALMON WA U S A STANDARDS EN 15649 2012 W A S 0 083bar PRODUCT REBOUND 12 1 2psi MADE IN PR C DESIGNED IN U S A No protection against drowning Keine Schutz gegen Ertrinken Pas de protection contre la noayada No protege contra el ahogamiento Nessuna protezione contro I affogamento Beschermt niet tegen verdrinken Only for swimmers Nur fur schwimmer Seulement pour les nageurs Solo para nadadores Solo per i nuotatori Alleen voor zwemmers 368 cm 145 368 cm 1457 79cm 317 Rebound 12 L W H SI Q ky N 2012 Prolonged exposure to salt water can damage and or shorten the expected lifetime of this product The ma
11. er when you contact Aquaglide or your Product can be returned only if a return autho dealer with any warranty claim A If a product is deemed to be defective by Aqua 5 This warranty does not cover damage caused Aquaglide Inc 1 North Shore Dr SE White Salmon WA 98672 TEL 509 493 4938 FAX 509 493 4966 www Aquaglide net
12. erator s Manual before use A CAUTION Watersports can be safe and fun for all levels of enthusiasts The Operator s Manual is presented to enhance your enjoyment of the sport It is intended to alert you to some of the potentially dangerous conditions that can arise in all watersports It is the owner s responsibility to read the owner s manual and instruct all users in the safe operation of these products By inflating these products you hereby agree to the Release of Liability Claim Waiver and Assumption of Risk Agreement in the Owner s Manual To reduce the risk of injury or death follow these guidelines Carefully read the product Owner s Manual and follow the instructions Take all reasonable precautions in the use and operation of your trampoline and or aquapark Teach anyone using your trampoline and or aquapark about safe guidelines prior to use Know your own limits Stop when you are tired Act responsibly Be in good physical condition and be cautious in your use of this or any other water sports product Periodically check mooring bridles and or lines to ensure safety Replace any portion of mooring and or connection system that shows signs of wear Do not add any hardware or attachments not otherwise supplied by the manufacturer THE WARNINGS AND PRACTICES SET FORTH ABOVE REPRESENT SOME COMMON RISKS ENCOUNTERED BY USERS AND DOES NOT PURPORT TO COVER ALL INSTANCES OF RISK OR DANGER PLEASE USE CO
13. erous objects i e rocks or stumps 3 Keep a safe distance from docks boats boat lifts and any other structures DO NOT tie the product to a dock 4 Anchors and anchor line are 3 Pass the end of the webbing back through the sold separately We recommend open area of the two D Rings on top as shown 3 at least 150 Ibs of weight for the 12 Rebound and 250 Ibs of weight for the 16 Rebound Now bring the webbing through the opening in the single D Ring on the platform as shown 4a 5 Fold the strap over onto the velcro 4b and place the other velcro tab in place to lock the strap 4c Ground screws or heavier anchors 300 Ibs or more should be used for Rebound 20 or smaller Rebounds when on large or windy bodies of water 5 Attach anchor line securely to the anchor Use a buoy tied to the other end of the rope to easily locate your anchor 6 When the product is in place remove the buoy and tie or shackle the anchor line to the anchor rings underneath the product Allow AT LEAST several feet of slack in the line before securing the line This will allow the product to move in wind or waves without displacing your anchor 7 If strong winds or storms are expected it is best to remove the product from the water and deflate it You can also move it closer to shore and secure it with lines Operation 1 This item is a water bouncer Users bounce near the center of the item This item m
14. ing very firm pressure f Rub the entire patch area and the edges of the patch using very firm pres sure g Allow to cure for at least 24 hours before inflating www Aquaglide net NOTICE Release of Liability Claim Waiver and Assumption of Risk Agreement By opening and assembling this product you are agreeing 1 to be bound to the terms set forth below and 2 to require anyone using this product to be bound by such terms If you are unwilling to be bound by these terms return this product before use for a full refund ASSUMPTION OF RISK Use of this product and any of its components involves certain inherent risks dangers and hazards which can result in serious personal injury and death In using the product you freely agree to assume and accept any and all known and unknown risks of injury while using this equipment The risks inherent in the sport can be greatly reduced by abiding by the Warning Guidelines listed in this Owner s Manual and by using common sense RELEASE AND WAIVER OF CLAIMS AGREEMENT In consideration of the sale of the product to you you hereby agree to the fullest extent permitted by law as follows TO WAIVE ANY AND ALL CLAIMS that you have or may in the future have against North Sports Inc and Aquaglide Inc its distributors and dealers resulting from use of this product and any of its components TO RELEASE North Sports Inc and Aquaglide Inc from any and all liability for any loss damage in
15. jury or expense that you or any users of this product may suffer or that your next of kin may suffer as a result of the use of this product due to any cause whatsoever including negligence or breach of contract on the part of North Sports Inc and Aquaglide Inc in the design or manufacture of this product and any of its components ARBITRATION n further consideration of the sale to you of this product and any of its components you hereby agree to submit to binding arbitration any and all claims which you believe you may have against North Sports Inc and Aquaglide Inc arising from the use of any North Sports Inc and Aquaglide Inc equipment or products The arbitration shall be pursuant to the rules of the American Arbitration Association Arbitration shall be commenced within 1 year from the date on which any alleged claim first arose Further the arbitration shall be held in White Salmon Washington unless otherwise mutually agreed to by all parties The submission to the American Arbitration Association shall be unlimited and the arbitration award may be enforced by any Court of competent jurisdiction BINDING EFFECT OF AGREEMENT In the event of your death or incapacity this Agreement shall be effective and binding upon your heirs next of kin executors administrators assigns and representatives ENTIRE AGREEMENT In entering into this Agreement you are not relying upon any oral or written representations other than what is set forth in
16. paced around the bouncer to help carry the Rebound using the provided transport handles NEVER DRAG YOUR REBOUND YOU MUST LIFT AND SET TO AVOID ANY ACCIDENTAL TEARING ON SHARP OBJECTS Aquaglide Inc 1 North Shore Dr SE White Salmon WA 98672 Tel 01 509 493 4938 Fax 01 509 493 4966 Aquapark If you have purchased a Complete Rebound Aquapark Set please see the following instruc tions to complete assembly If not please proceed to the Anchoring section 1 Roll out your i Log and connect it to the Rebound BEFORE INFLATING the i Log using the attached Interloc straps The i Log connects on the side of the bouncer 45 degrees clockwise from the access platform viewed from above Find 2 D rings on the tube approximately 14 above the water line Take the 2 Inter loc straps and connect the i Log to the Rebound tube according to the Interloc instructions shown below Once the straps are connected then inflate the i Log to 1 0 psi 0 069 bar until it is firm Check for proper air pressure using a manometer This will tighten the i Log to the side of the Rebound Be careful not to over inflate the i Log 2 Unroll and place the Slide on the ground next to the Rebound and inflate to 0 8 psi 0 055 bar untill it is firm Check for proper air pressure using a manometer Inflation times can vary by inflator but the slide should be firm and tight when completely
17. r SE White Salmon WA 98672 Tel 01 509 493 4938 Fax 01 509 493 4966 Owners Manual Reni BOUNCER AND BOARDING PLATFORM AQUAPARK SYSTEM 12 16 20 It is the owner s responsibility to read the owner s manual and instruct all users in the safe operation of these products By inflating these products you hereby agree to the Release of Liability Claim Waiver and Assump tion of Risk Agreement in this manual Please read this manual prior to inflating and using these products and keep for future reference As with any action sport recklessness inexperience misuse or neglect of the equipment may result in serious injury or death 4A WARNING USE OF THIS PRODUCT AND PARTICIPATION IN WATERSPORTS INVOLVES INHERENT RISKS OF INJURY OR DEATH This product should never be used by children except under adult supervision Not intended for use by children under 5 years of age This product is not a personal flotation device Always wear a floatation vest PFD as required by the authorities in area of use Never place wrists or feet through handles Do not use in shallow water less than 8 ft 2 44 m deep Do not use within 15ft 4 5 m of shore docks pilings or other hard objects Never swim under this product Do not jump or dive from this product Do not exceed the manufacturer s recommended number of users for this particular product Do not use while under the influence of alcohol or drugs Read Op
18. r Inflation times can vary by inflator but the tube should be firm and tight when completely inflated In hot weather be sure to leave room for air expansion DO NOT OVER FILL Close the valve and secure valve cap Warning Do not use an air compressor to inflate tube Air compressors are designed for high pressure inflation and can cause tube to burst if over inflated The inflator deflator described above cannot over inflate the tube 4 Roll out your Swimstep access platform and connect it to the Rebound BEFORE INFLATING the platform using the attached Interloc straps The access platform connects on the side of the bouncer where the warnings are located Find the 2 rings on the tube near the water line Use 2 Interloc straps to connect the access platform to the tube as shown in Fig 2 Secure the straps according to the following Interloc instructions shown in Figure 3a 3e Once the straps are connected then inflate the boarding platform to 0 8 psi 0 055 bar until it is firm Check for proper air pressure using a manometer This will tighten the platform to the side of the Rebound Be careful not to over inflate the access platform 5 Congratulations You are now ready to place your Rebound in the water NOTE If you have purchased a Complete Rebound Aquapark Set please proceed to the Aquapark section for further assembly details To launch your Rebound bouncer make sure to have at least 3 4 people evenly s
19. rine environment includes many damaging elements including rrosion abrasion and damage from marine life such as barnacles Regular cleaning and rinsing with fresh water can reduce these risks A PVC safe antifouling paint should be used to help protect this product against marine growth DAMAGE CAUSED BY EXPOSURE TO SALT WATER IS NOT COVERED BY WARRANTY Aquaglide Inc 1 North Shore Dr SE White Salmon WA 98672 Compliant with DIN EN 15649 Aqua ie PLAT Peformance AQUAGLIDE INC WHITE SALMON WA U S A STANDARDS EN 15649 2012 W A S 0 083bar PRODUCT REBOUND 16 1 2psi MADE IN PR C DESIGNED IN U S A No protection against drowning Keine Schutz gegen Ertrinken Pas de protection contre la noayada No protege contra el ahogamiento Nessuna protezione contro I affogamento Beschermt niet tegen verdrinken Only for swimmers Nur fur schwimmer Seulement pour les nageurs Solo para nadadores Solo per i nuotatori Alleen voor zwemmers 488 cm 192 488 cm 192 91cm 36 Rebound 16 L W H e Q 8 N 2012 A WARNING Prolonged exposure to salt water can damage and or shorten the expected lifetime of this product The marine environment includes many damaging elements including corrosion abrasion and damage from marine life such as barnacles Regular cleaning and rinsing with fresh water can reduce these risks A PVC safe antifouling paint should
20. se rules Before you start Familiarize yourself with all applicable federal state and local laws the risks inherent in the sport and the proper use of the equipment Know the waterways Use caution and common sense Do not use in recreational swimming pools within 3 0m 10ft of commercial pool edge or within 4 5m 15ft of boats docks or other hard obstructions Do not attempt or allow somersaults Landing on the head or neck can cause serious injury paralysis or death Never use at night or in low light conditions Never use in poor weather conditions with excessive wind waves or lightning Do not use on dry land Do no use without proper anchoring Do not dive head first or swim under your Rebound Take extreme care when swimming between the shore and the product Be cautious of any boat traffic or other obstructions Ensure all users are capable swimmers and are not excessively fatigued Do not allow anyone to attempt to swim to or from the product that are not physically able to do so Always ensure that the swimming area around the product is free of submerged logs rocks and sandbars Ask about the local water conditiions before use Only allow use of the product with proper supervision Secure the product when not in use to prevent access by any other users Do not jump or dive from this item Do not jump onto this item from any other item Aquaglide Inc 1 North Shore D
21. t the end of 30 must come in writing from Aquaglide days or upon refusal of the quote Aquaglide will return the product in the condition in which it was 7 The warranty for any repaired or replacement received at the customer s expense The customer cover use in schools or rental operations Warranty term for commercial use is 1 year 3 Aquaglide will make the final warranty determi nation which may require inspection and or photos equipment is good from the date of the original agrees to authorize Aquaglide Inc to charge the oe pd ici cry hm dele We puro o customer cet card fo any coste rot covered choice freight prepaid or by email to warranty under the terms and conditions of the Aquaglide aquaglide net 8 Any warranty claims must be accompanied Warranty by the original purchase receipt The name of the i retailer and date of purchase must be clear and Serial Number i glide the warranty covers the repair or replacement legible All Aquagiide Platinum products are marked with of the defective product only Aquaglide will not l l a serial number near the main inflation valve 1 be responsible for any costs losses or damages 9 There are no warranties which extend beyond The serial number may be stamped into the PVC incurred as A resultof loss of ss of pro duct the warranty specified here directly around the valve or it may be visible on a welded plate near the valve Please include Returns and Service Policy this numb
22. ust be used with at least one Aquaglide Platinum boarding platform 2 When connecting multiple items use only Aquaglide Interloc straps and connecting rings according to the Interloc Strap instructions provided Make sure that the connection is tight and that there is NO GAP greater than 25mm 3 4 between items IMPORTANT Failure to connect these items properly may result in injury or death Care and Maintenance 1 While your product has been initially treated with UV protectant long term exposure to sunlight will damage the product Regularly apply a UV protec tant to the exposed surface of the tube to ensure the life of your product We recommend using ONLY 303 UV Protectant intended for use on vinyl for this purpose Monthly application while the product is in use is recommended NOT DOING SO OVER LONG TERM WILL VOID THE WARRANTY 303 Protectant is available at most watersports dealers or online at www 303 products com 2 WARNING Certain products especially petrolium based solvents cleaners and protectants such as ArmorAll can damage the product and use of these products will void the warranty 3 WARNING Use of a high pressure washer will damage the product and void the warranty To clean use a soft bristle brush with mild soap and fresh water 303 UV Protectant contains a safe for vinyl cleaner and can be used to clean and protect the product at the same time 4 Check the inflation of your tube often Check
Download Pdf Manuals
Related Search