Home
DAG Series FXSFXO Voice Gateway User Manual V2.0
Contents
1. onhook e Configure gateway IP address Offhook input 156 172 16 0 1 onhook 3 Query the IP address of device Offhook input 158 4 If the DAG serial uses PPPoE method to get IP address it need to configure by web browser Note the telephone will play voice prompt Setting successfully if the step is correct 4 WEB Configuration 4 1 WEB Login Device is connecting to network properly refer to chapter 3 Operation Offhook and dial 158 to inquire device IP address 4 1 1 Login Device LAN port default IP address is 192 168 11 1 WAN port default obtain IP address by DHCP Advice to modify the IP address of the local computer equipment and ensure that 9 Dinstar Technologies Co Ltd DINSTAR DAG1000 2000 Series FXS FXO Voice Gateway User Manual are on the same IP segment with Windows 7 as an example the local computer IP address change for 192 168 11 10 Internet Protocol Version 4 TCP IPv4 Properties o eem You can get IP settings assigned automatically if your network supports this capability Otherwise you need to ask your network administrator for the appropriate IP settings 6 Obtain an IP address automatically Use the following IP address IP address Subnet mask Default gateway Obtain DNS server address automatically Use the following DNS server addresses Preferred DNS server Alternate DNS server E Validate settings upon exit Figure
2. Figure 4 11 5 Ping Parameter Interface 4 11 6 Tracert Test Tracert is trace router and used to tracking routing Tracert sends a sequence of Internet Control Message Protocol ICMP echo request packets addressed to a destination host Determining the intermediate routers traversed involves adjusting the time to live TTL aka hop limit Internet Protocol parameter Frequently starting with a value like 128 Windows or 64 Linux routers decrement this and discard a packet when the TTL value has reached zero returning the ICMP error message ICMP Time Exceeded Tracert works by increasing the TTL value of each successive set of packets sent The first set of packets sent have a hop limit value of 1 expecting that they are not forwarded by the first router The next set have a hop limit value of 2 so that the second router will send the error reply This continues until the destination host receives the packets and returns an ICMP Echo Reply message Trace route uses the returned ICMP messages to produce a list of hops which usually consists 54 Dinstar Technologies Co Ltd DINSTAR DAG1000 2000 Series FXS FXO Voice Gateway User Manual of routers and layer 3 switches that the packets have traversed The timestamp values returned for each router along the path are the delay aka latency values typically measured in milliseconds for each packet Tracert introduce 1 Click tracert test 2 Fill IP address or domain connect
3. Outgoing call Parameters Outgoing Call to PSTN One Stage Dialing Enable Hook Flash Enable Dial Delay ms Answer to Caller when Polarity Reversal Detected Enable Delay Time after FXO Offhook Ps Dial Mode gt One Stage Dialing Enable this function FXO port directly sent the dial number without call extension gt Dial Delay Timer of outgoing call dialing To call out while match with routing rule successfully gt Polarity Reversal Detect To enable or disable Polarity Reversal gt Delay Time after FXO Offhook Timer of the gateway to send SIP 2000K to VoIP In case the fixed line doesn t supply answer signal the gateway will send answer signal to VoIP side 31 Dinstar Technologies Co Ltd gt DINSTAR DAG1000 2000 Series FXS FXO Voice Gateway User Manual Onhook when Busy Tone Detected Enable No Current Detected Enable Current Disconnect Threshold ms DC Impedance 50 Ohm K AC Impedance 600 Ohmi Ke Automatch FXO Impedance Busy Tone Detected The FXO port will release while busy tone detected No current detected The FXO port will release while no current detected on the phone line AC DC impedance To match with the impedance of phone line automatically or configure impedance manually Here is the list that support on the gateway 400 m 270 Ohm 750 Ohm 150 nF and 275 Ohm 760 Ohm 150 nF 220 Ohm 620 Ohm 120 nF and 220 Ohm 620 Ohm 115 nF 3 0 Ohm 620 Ohm 310 nF 320 Ohm 1
4. SIP server configuration interface as follows SIP Server Primary SIP Server Primary SIP Server Address 172 116 100 102 Primary SIP Server Port Default 5060 Register Interval Default 1800 s Heartbeat E Enable Secondary SIP Server secondary SIP Server Address Po Secondary SIP Server Port Default 5060 Register Interval Default 1600 1800 S Heartbeat E Enable Local SIP Port Use Random Port E Enable S t Local SIP Port 5060 Figure 4 6 1 SIP Server Configuration Interface SIP parameter description Primary SIP Server IP SIP Server IP address or Domain name provided by VoIP service provider Primary SIP Server port Service port default is 5060 protects registrar against excessively frequent registration refreshes Register interval while limiting the state Every once in a while send request for registration to the terminal server default is 1800s Heartbeat Heartbeat message detect the connection status between device and SIP server Secondary SIP Server IP l l l l ap Backup SIP Server s IP address or Domain name provided by VoIP service provider address Secondary SIP Server port Service port default is 5060 protects registrar against excessively frequent registration refreshes Secondary SIP server So l l l l l l while limiting the state Every once in a while send request for registration to the Register interval l l terminal server default is 1800s Secondary SIP heartbeat Heartbeat messa
5. DINSTAR DAG Series FXSFXO Voice Gateway User Manual V2 0 Dinstar Technologies Co Ltd Address Floor 6 Guoxing Building Changxing Road Nanshan District Shenzhen China 518052 Telephone 86 755 26456664 Fax 86 755 26456659 Email Sales dinstar com support dinstar com Website www dinstar com File Name Document Version Firmware Version Date Revised by Revision Records DAG Series FXS FXO Voice Gateway User Manual 2 11 08 07 2014 03 16 Technical Support Department Table of Contents Selfie ise ele le EEN 1 EE OVE VION EE 1 1 2 Ed uibpmMent appeatanCe sennen oop tnntbeasehiunistuustedelad ceatons 1 Lo ge EE e EE 2 1 4 Network Applications eeraa E E 2 LS Funcions ana Features E 3 1 5 1 Protocol standard supporter 3 1 5 2 Voice and Fax Parameters ccccescssscessssccssssecsssesecsssesevsseeseres 3 1 5 3 Supplementary service ccccecesecesssccesseeecessesecsssesevasesevsseeseras 3 Beleg ODETAUON S EE 4 Zod Lee WEE 4 2 1 1 Phone or Extension Number 4 PMD Reeg e UE 4 Pe SCH ee Ve EE 5 Zio CIWAN Cl RE 5 2 Ay Call Ve EE 5 ZAC EE Mans ee 5 2 4 2 Atenaed WFAN STN E 6 2S CR O S 6 2 6 Sending and RECEIVING Fax 8 2 6 1 DAG FXS support four fax modes eerren 8 2106 2 38 and PASS 1 nl ne In E 8 OCN RE OPTA ON WEE 8 E fa Blo ITT Ela Tele EE 8 EEN EE asim hema 8 3 3 Configure LAN Porte IP ACdIreS cccccsssscsssscsssscessscesscessscesseecsseecses 8 WEB COMBOUP
6. string is a choice of dial up solutions means choose anyone means one reports letter T AA D means detected timer overtime x means any data means multiple characters can be behind include 0 means report immediately Digit Map Syntax 1 Supported objects Digit A digit from 0 to 9 Timer The symbol T matching a timer expiry DTMF A digit a timer or one of the symbols A B C D or 38 Dinstar Technologies Co Ltd DINSTAR DAG1000 2000 Series FXS FXO Voice Gateway User Manual 2 Range One or more DTMF symbols enclosed between square brackets and but only one can be selected 3 Range One or more expressions enclosed between round brackets and but only one can be selected 4 Separator Separated expressions or DTMF symbols 5 Subrange Two digits separated by hyphen which matches any digit between and including the two The subrange construct can only be used inside a range construct i e between and J 6 Wildcard x matches any digit 0 to 9 7 Modifiers Match 0 or more times 8 Modifiers Match 1 or more times 9 Modifiers Match O or 1 times Example Assume we have the following digit maps 1 XXXXXXX X11 and a current dial string of 41 Given the input 1 the current dial string becomes 411 We have a partial match with xxxxxxx but a complete match with x11 and hence we send
7. 411 to the Call Agent 2 2 8 XXXXXX 13XXXXXXXXX Means that first is 2 3 4 5 6 7 or 8 followed by 6 digits 39 Dinstar Technologies Co Ltd DINSTAR DAG1000 2000 Series FXS FXO Voice Gateway User Manual or first is 13 followed by 9 digits 3 13 15 18 XXXXXXXXX Means that first is 13 15 or 18 followed by 8 digits 4 1 357 9 xx Means that first is 1 2 3 or 5 or 7 8 9 followed by 2 digits 4 8 6 Feature Codec Feature codec includes device function and call function Feature codec as follow Feature Code Feature Codes Use Default Status Device Function Inquiry LAN IP Enable Le Inquiry WAN IP Inquiry Phone Number Setting IP Mode Network Work Mode Configure IP Address Network Subnet Mask Configure Enable Le Network Gateway Configure Enable Renew DHCP Access WEB by WAN in Route Mode Enable e Reset Factory Fi Enable Le Restart Device Enable Call Function Call Onhold Offhold Enable Le Call by IP Enable Je Call Waiting Activate Enable Call Waiting Deactivate Enable Blind Transfer Call Forward Unconditional Activate Fe Call Forward Unconditional Deactivate fat Enable Le Call Forward Busy Activate Lean Fj Enable 1 Do Not Disturb Activate Enable Do Not Disturb Deactivate Enable Dial Voicemail Note Please finish dialing the feauture code within 2s when using the Call holding functio
8. The device must restart to take effect Figure 4 5 2 Bridge Mode Link Speed amp Duplex used to select Ethernet port work mode include 5 kinds of Choice Auto Detect 10Mbps half duplex 10Mbps full duplex 100Mbpshalf duplex 100Mbps full duplex default is Auto Detec e When select Obtain IP address automatically DAG will obtain IP address by DHCP e When select Use the following IP address that configure DAG to fixed IP address mode When select PPPoE please fill in account and password offered by ISP in internet account and password Notes 1 If select automatically obtain IP address please ensure DHCP server in network and work normally 2 Under route mode please configure LAN port and WAN port in different segment otherwise DAG can t work normally 17 Dinstar Technologies Co Ltd DINSTAR DAG1000 2000 Series FXS FXO Voice Gateway User Manual 3 Under route mode login DAG configuration interface only used LAN port 4 After configuration restart device configuration validation 4 5 2 VLAN Parameter Generally Internet provides only Best Effort Service Since ethernet is the most spread LAN access technology importance of providing it a quality of service mechanism ought not to be neglected Ethernet technology also used as WAN technology not only as LAN technology Due to rapidly increasing use Internet through Public Switched Telecommunication
9. 4 1 1Modify IP address Check connection between computer and device click Start gt run gt input cmd run ping 192 168 11 10 t order to check the connectivity between them 4 1 2 Login WEB Open web browser then input IP address of device Press Enter it pop up logging on identity authentication interface Authentication Required _ 3 The server 172 16 77 10 80 requires a username and password The server says Web Config System UserName admin Password zz Cent Figure 4 1 1 DAG FXS Login Interface 10 Dinstar Technologies Co Ltd DINSTAR DAG1000 2000 Series FXS FXO Voice Gateway User Manual Default username and password admin admin click OK to entry into web interface DS DINSTAR Web Management System System Information Status amp Statistics Quick Setup Wizard MAC Address 00 1F D6 A0 01 04 Network Network Mode Bridge SIP Server Port IP Address 172 16 66 3 255 255 0 0 172 16 1 1 Advanced DNS Server 202 96 128 68 202 96 134 133 Call amp Routing Manipulation Maintenance System Uptime 70h 10m 50s NTP Status Succeed Network Traffic Stat Received 1912835244 bytes Sent 818891 bytes DAG1000 4S40 Rev 2 11 08 07 Beta 1 PCB 23 1 LOGIC 0 BIOS 1 Built on Apr 18 2014 8 Version 13 36 1 Figure 4 1 2 DAG Configure Interface 4 2 Navigation Tree DAG series voice gateway web configuration interface mainly includes navigation tree a
10. WAN port hardware address The device ID in HEX format Display network mode include bridge and router If it is bridge WAN port display Network Mode Network and the WAN port as same as the LAN port Shows WAN IP address of DAG DHCP mode all the field values for the Static IP mode are not used even though they are still saved in the Flash memory The DAG acquires its IP address from the first DHCP server it discovers from the LAN it is connected Using the PPPoE feature set the PPPoE account settings The DAG will establish a PPPoE session if any of the PPPoE fields is set Static IP mode configure the IP address Subnet Mask Default Router IP address DNS Server 1 primary DNS Server 2 secondary fields These field sare set to zero by default LAN Port Shows LAN IP address of DAG if network Mode is bridge LAN port won t display DNS Server Display DNS server IP address and default gateway information System Uptime Time elapsed from device power on to now Network Connection The current NAT mapping maximum number of concurrent mapping Occupancy Ratio number Network Traffic Statics Total bytes of message received and sent by network port Includes product mode software version hardware version and built time etc 13 Dinstar Technologies Co Ltd DINSTAR DAG1000 2000 Series FXS FXO Voice Gateway User Manual 4 3 2 Registration Information Port Registration Information Figure 4 3 2 Port and Por
11. information provided by VoIP service provider ITSP Usually in SIPUser ID the form of digit similar to phone number or actually a phone number Primary Secondary SIP SIP service subscriber s Authenticate ID used for authentication Can be 26 Dinstar Technologies Co Ltd DINSTAR DAG1000 2000 Series FXS FXO Voice Gateway User Manual Authenticate ID identical to or different from SIP User ID Primary Secondary l l l l SIP password which registers to soft switch SIP server Authenticate password l Pre assign an extension or phone number so that automatically dial a number Offhook Auto dial l as soon as you pick up the phone set l l Delay 0 3 seconds to automatically dial a number 0 means dial number Auto dial Delay Time l l immediately DND Do not disturb the phone set won t receive any calls in case it enabled Caller ID Enable or disable caller ID for corresponding port call forward unconditional all incoming calls willforward to pre assigned Number for CFU l number automatically Call forward on busy if the line is busy the call will forward to pre assigned Number for CFB l number automatically Call forward no reply if the line is not answer the call the call will forward to Number for CFNRy l l pre assigned number automatically 7 If call waiting enabled it will send a special tone if another caller tries to reach Call Waiting l you when you are using your telephone Play Call Waiting Tone Enable call wai
12. the call Caller A can press flash to resume call with Caller B 2 5 Call Features DAG FXS support all traditional and senior phone function Table 2 5 1 Feature Codec Feature Codec Operation Instructions 158 View the LAN port IP address 159 View the WAN port IP address 1147 Inquire port account 150 Set the way of obtain IP address Dinstar Technologies Co Ltd DINSTAR DAG1000 2000 Series FXS FXO Voice Gateway User Manual 1157 2 Set network method 1527 Set IP address 1537 Set Subnet mask 156 Set default gateway IP address 193 Obtain IP address through DHCP again 160 1 Open WAN port to access web 166 000000 Factory reset 111 Restart device a Call hold 47 IP address call 51 Enable call waiting 50 Disable call waiting 87 Blind transfer eI 2 Enable Unconditional Call Forward 73 Disable Unconditional Call Forward 9Q Enable Busy Call Forward O1 Disable Busy Call Forward 925 Enable No Answer Call Forward O3 Disable No Answer Call Forward 78 Enable DND 79 Disable DND 200 Access Voice mail Switch between incoming calls If not in session flash hook will switch a Flash Hook new channel for new call Dinstar Technologies Co Ltd DINSTAR DAG1000 2000 Series FXS FXO Voice Gateway User Manual 2 6 Sending and Receiving Fax 2 6 1 DAG FXS support four fax modes 1 T 38 FoIP 2 Pass Through 3 Modem 4 adaptive 2
13. zone of confidence and not allow any access separation of inside and outside the network protect user information DMZ can be understood that a special areas of the network and different from 21 Dinstar Technologies Co Ltd DINSTAR DAG1000 2000 Series FXS FXO Voice Gateway User Manual the external network or intranet Public server that does not contain confidential information usually placed in DMZ such as web Mail FTP etc Accuser from intranet can visit the service of DMZ but can t come into contact with confidential or private information stored in the network Even if DMZ server is damaged it will not be confidential information in the internal network DMZ Host DMZ Host IF Address Enable Note The IF address needs to be in the same subnet with LAN port Figure 4 5 6 DMZ Configuration Interface Note After configuration restart device configuration validation 4 5 6 Forward Rule Routing mode In some cases LAN network equipment need to provide some communication in WAN network such as port for 21 FTP service This time can be configured forwarding rules for the network equipment Service ports namely the need to provide service network mouth WAN ports IP address that LAN network provide services to the mouth of the network equipment IP address the protocol is TCP or UDP The different between forward rule and DMZ host is that DMZ Host offers continuous multiple Port 0 1024 and all the for
14. 050 Ohml 230 nF 3 0 Ohm 620 Ohm 1710 nF 275 Ohm 760 Ohm 115 nF 120 Ohm 620 Ohm 1710 nF 350 Ohm 1000 Ohm 210 nF 200 Ohm 680 Ohm 100 nF 600 Ohm 2 16 uF 900 Ohm 1 uF 900 Ohm 16 uF 600 Ohm 1 uF Global Complex Impedance Je dee AC AE Ae an AC aa 4 8 2 Media Parameter Media parameter mainly include RTP start port DTMF parameter PreferedVocoder Configuration Interface as follow 32 Dinstar Technologies Co Ltd DINSTAR DAG1000 2000 Series FXS FXO Voice Gateway User Manual Media Parameter RIP Start Part DTMF Parameter DTMF Method SIGNAL DTMF Gain EIS e Prefered Vocoder Packetization Coder Name Payload Type Time ms Rate kbps Silence Suppression Disable Le 2nd amu 2 Disable 3rd G711A m 2 54 Disable Figure 4 8 2 Media Parameter Configuration Interface Media parameter description RTP Start Port Default RTP port 8000 DTMF Method SINGAL INBAND RFC2833 It is configurable When RFC2833 is selected RFC2833 Payload Type Optimization payload negotiation parameter with remote side it includes two options Local and remote RFC2833 Payload Type Payloadvalue default is 101 DTMF Gain Default is 0 DB DTMF Send Interval DTMF send signal interval default is 200ms DAG supports G729 G711U G711A G723 while Coder Name it make outgoing call G 729 will used as figure 4 8 2 displayed Each kind of coding has a unique type load Payload Type value refer t
15. 50 410 ET Gs EE 51 Me Me VUE STN MG Ee 51 4 11 1 Gleef EE TEE 51 ode Firmware Uploader ee 52 Alle Data BaCKUD EE 53 LEDI EROS ON EE 53 sro PNO TEST ee 53 MAO leien ER HOSE ER 54 4 11 7 Password Modification 55 FIRS Te rei RESET eonenna O 56 A 11 9 Device Ee Eeer 56 VE ee TEE 57 DINSTAR DAG1000 2000 Series FXS FXO Voice Gateway User Manual 1 Equipment Introduction 1 1 Overview Thanks for purchasing Dinstar DAG Hereinafter referred to as the DAG series FXS FXO hybrid analog voice gateway DAG series FXS FXO hybrid analog gateway is access gateway based on IP network It can provide low cost simple operation VoIP solutions for small enterprise the family office remote office and branch enterprise DAG connects to analog telephone fax and traditional analog PBX with standard voice interfaces and provided high quality voice service DAG series FXS FXO hybrid VoIP access gateway has life line function DAG series FXS FXO hybrid gateway includes following model m DAG1000 4S40 m DAG2000 8S80 This manual mainly to DAG1000 4S40 as examples introduce the function of devices and parameter configuration 1 2 Equipment appearance Figure 1 1DAG1000 4S40 Figure 1 2 DAG2000 8S80 Dinstar Technologies Co Ltd DINSTAR DAG1000 2000 Series FXS FXO Voice Gateway User Manual 1 3 Power supply DAG1000 4S40 is Cassette equipment with placed on desk and adopts AC 110 240 V power supply with the power adapte
16. 6 2 T 38 and Pass Through T 38 is the preferred method because it is more reliable and works well in most network conditions If the service provider supports T 38 please use this method by selecting T 38 as fax mode default If the service provider does not support T 38 pass through mode may be used If you have problems with sending or receiving Fax toggle the Fax Tone Detection Mode setting 3 Local IVR Operation 3 1 Inquire IP address Analog phone connected with FXS ports of device then pick up after dial tone dialing 158 to inquire LAN port IP address and dialing 159 to inquire WAN port IP address 3 2 Factory Reset After picking up dial 166 000000 then onhook and restart after Setting successful 3 3 Configure LAN Port s IP Address Before configuration please ensure 1 The device is power on 2 devices connecting Dinstar Technologies Co Ltd DINSTAR DAG1000 2000 Series FXS FXO Voice Gateway User Manual to network 3 Telephone is connecting to FXS port of device 1 Configure dynamic IP address by DHCP Offhook Dial 150 2 Onhook If the equipment hint success after 10 seconds and restart the equipment Power off then power on 2 Configure Static IP address Offhook Dial 150 1 Onhook Then configure IP and mask as follow e Configure IP address Offhook input 152 172 16 0 100 onhook Configure subnet mask Offhook input 153 255 255 0 0
17. AU eege eegener 9 AL WEB WOON A BEE 9 care ies US e ln E 9 e GE Beie Ad el Ren eee re nr et a em nem ene ne me ee 10 4 2 Edel gen gl 11 4 3 State and Ren eA S o oo E 12 4 3 1 System Information 12 4 3 2 Registration Information 14 43 3 he cy 6 B Saar EE 14 45324 Te BE le 14 ATF QUICK SOLUS VVIZN e WE 15 4 5 Network Configuration ccccccccsssccsssccessecesseecesseecesseecsseeeesseeeesseeeeses 15 APs KENE 15 Aue NLAIN Paramete ee eetehen eege diese 18 4 5 3 MAC Clone Routing model 20 4 5 4 DHCP Server Routing mode 21 4 5 5 DMZ Host Routing mode 21 4 5 6 Forward Rule Routing mode 22 4 5 7 Static ROULC Ee UE 23 SEENEN 24 APLC ISU E S EEN 24 A PORE KEENT eene 26 TOG GNC D 27 48 1 FXS FXO DalaMelerS o sd icant aiid EE 27 4 8 2 Media Parameter ccccccccessssscessssecessseecessesecessesecessesecessesevessases 32 SEET ees 24 e dE heel EE 37 ee IGN Ee EE 38 4 8 6 Feature COGEG ed 40 4 8 7 SyStEM Paramete ssccssccsssessctsscusssnsconscersssnscenseurssusconseenseens 42 49 Cal Ae ln Le DEE 43 e GE ele GOUD jaca cree ac casa teen oe esoon T TO 43 TI Ltd le 45 4 9 3 Routing CONFIGUIATION csccccsscscesstscessrscessecescsecesreceserevesenes 46 EIA AP Vel ROUTING EE 47 4 9 5 Tele ROUTING eigene 48 4 10 Manipulation Configuration ccccccsccesseccssecesseecesseecesseeeesseeesseeeeeas 49 410 UF ces Be gt pe ee eege Gegen 49 e el emt e EE
18. After ring the FXO port will ringing to FXO port then start to detect CID gt Send Original CID when Call from PSTN e From Mode when CID Is Available Used to configure From Mode when Caller ID Is Available when call from PSTN to VoIP The SIP header should be matched with follow formats Display CID From Mike lt sip CID host com gt tag 51088abb User ID CID From 201 lt sip CID host com gt tag 51088abb CID CID From Caller ID lt sip Caller D host com gt tag 51088abb CID User ID From Caller ID lt sip 201 host com gt tag 51088abb e From Mode when Caller ID Is Unavailable Used to configure From Mode when Caller ID Is Unavailable Anonymous From lt sip Anonymous host com gt tag 51088abb Display User ID From Mike lt sip 201 host com gt tag 51088abb gt Keep onhook until callee answered 30 Dinstar Technologies Co Ltd DINSTAR DAG1000 2000 Series FXS FXO Voice Gateway User Manual When the gateway get incoming call from PSTN network the modular will answer the call then start to DTMF or route to destination hotline number While this option enabled the modular won t answer the call but routing to destination hotline number till it getting answer gt Play Hint to FXO Enable this function when call from PSTN to FXO port FXO port will play prompt tone please dial the extension number gt Allow Call to SIP Server without Registration To enable peer to peer call without registration
19. DAG1000 2000 Series FXS FXO Voice Gateway User Manual Suffix to Add Add a number suffix Number of Digits to Leave from Starting from the right to retain the called number digits Right 4 10 2 Tel IP Caller Tel IP Caller Add Index 21 Je Description Sr Port Group Callee Prefix Caller Pref Calls to Port Port Group Oirtunk Any SIP Server Stripped Digits from Left Po Stripped Digits from Right Po Prefix to Add pd Suticto Ad Po Number of Digits to Leave fram Right Co Reset Canoe NOTE any in Callee Prefix or Caller Prefix means wildcard string Figure 4 10 2 Tel IP Caller Configuration parameters are the same with IP gt Tel Callee 50 Dinstar Technologies Co Ltd DINSTAR DAG1000 2000 Series FXS FXO Voice Gateway User Manual 4 10 3 Tel IP Callee Tel IP Callee Add Index 31 Description Calls from S Port Port Group sd Caller Prefix Callee Prefix Calls to Port Port Group P Trunk Any SIP Server stripped Digits from Lett stripped Digits from Right Prefix to Add Suffix to Add Number of Digits to Leave from Right NOTE any in Callee Prefix or Caller Prefix means wildcard string Figure 4 10 3 Tel IPCallee Configuration parameters are the same with Tel gt IP Caller 4 11 Maintenance 4 11 1 Syslog Parameter Syslog is a protocol used in TCP IP network transmission of record of
20. Network PSTN Telephone Companies are forced to implement IP based networks as their PSTN backbones A network like this without any Quality of Service mechanisms would be disastrous Just imagine yourself trying to get an emergency call through while others just surf the Internet 1 802 1Q The IEEE 802 1Q standard defines architecture for Virtual Bridged LANs the services provided in Virtual Bridged LANs and the protocols and algorithms involved in the provision of those services No Quality of Service mechanisms are defined in this standard but an important requirement for providing QoS is included in this standard e g abitity to regenerate user priority of received frames using priority information contained in the frame and the User Priority Regeneration Table for the reception Port 2 802 1p IEEE 802 1p standard Traffic class expediting and dynamic multicast filtering It describes important methods for providing QoS at MAC level IEEE 802 1p is in fact quite good Lower priority level packets are not sent if there is packets in queued in higher level queues IEEE 802 1p describes no admission control protocols It would be possible to give Network Control priority to all packets and the network would be easily congested 18 Dinstar Technologies Co Ltd DINSTAR DAG1000 2000 Series FXS FXO Voice Gateway User Manual There are three VLAN data VLAN voice LAN and management VLAN VLAN configuration interface as fo
21. d Po secondary Display Name secondary SIP User ID secondary Authenticate ID secondary Authenticate Password Offhook Auto Dial Auto Dial Delay Time Port Select Pick Up on Group Port E Port over E Port 1 Fx5 E Port 2 Fx8 E Port 3 FXS E Port 4 FX0 E Port 5 FXO E Port 6 FXO E Port 7 FX0 Figure 4 9 1 port group configuration interface i Port groupNumber It uniquely identifies a route range from ndex 0 7 E Port group description its purpose is so you can identify the Description port group with a meaningful name Port group display which will be used in SIP message example INVITE sip bob biloxi com SIP 2 0 l l Via SIP 2 0 UDPpc33 atlanta com branch z9hG4bK776asdhds Primary Secondary Display Name Max Forwards 70 To Bob lt sip bob biloxi com gt From Alice lt sip alice atlanta com gt tag 1928301774 Here Bob and Alice is the display User account information provided by VoIP service provider Primary Secondary SIP User ID ITSP Usually in the form of digit similar to phone number or actually a phone number l l SIP service subscriber s Authenticate ID used for Primary Secondary Authenticate ID a l l l authentication Can be identical to or different from SIP User 44 Dinstar Technologies Co Ltd DINSTAR DAG1000 2000 Series FXS FXO Voice Gateway User Manual a Primary Secondary Authenticate Password of SIP user ID Password Offhook Auto Dial Set Auto dial number to compl
22. ed click start Tracer Test Destination Max Hops 1 255 information Figure 4 11 6 Tracert Test Interface 4 11 7 Password Modification Includes WEB username and password Telenet username and password modify Note Default web and telnet username and password is admin admin 55 Dinstar Technologies Co Ltd DINSTAR DAG1000 2000 Series FXS FXO Voice Gateway User Manual Password Modification Web Config Old Web Username Old Web Password New Web Username New Web Password Confirm Web Password Telnet Config Old Telnet Username Old Telnet Password New Telnet Username New Telnet Password Confirm Telnet Password Figure 4 11 7 Password Modification Interface 4 11 8 Factory Reset Click Apply to restore the factory settings Factory Reset Click the button below to reset to factory default settings Apply Figure 4 11 8 Factory Reset Interface 4 11 9 Device Restart Click the Save button in the Configuration page to save the changes to the equipment configuration The following screen confirms that the changes are saved If the changes need restart reboot or power cycle the equipment to make the changes take effect Restart Click the button below to restart the device Restart Figure 4 11 9 Device Restart 56 Dinstar Technologies Co Ltd DINSTAR DAG1000 2000 Series FXS FXO Voice Gateway User Manual 5 Glossary e DNS Domain Name Syste
23. eign communication agreement while the forward rule offers a single or a few port foreign communication on some protocol When the conflicts exist between forward rule and DMZ host the configuration of forwarding rules is preferred Forward rule configuration interface as follows 22 Dinstar Technologies Co Ltd DINSTAR DAG1000 2000 Series FXS FXO Voice Gateway User Manual Forward Rule Table Server Port IP Address Protocol Enable Po cr G D sn Om tm WwW ha Notes 1 IP Address needs to be in the same subnet with LAN port 2 Server Port range 0 65535 Figure 4 5 7 Forward rule configuration interface 4 5 7 Static Route Table Static Route Table is IP communication direction in network generally do not need to configure static route When there are many segments in LAN network and need to complete some specific application among these segments the static route need to be configured Static Route configuration interface as follows Static Route Table ID Dest IP Address Subnet Mask Nexthop 2 3 4 5 D 7 H Figure 4 5 8 Static route configuration Interface 23 Dinstar Technologies Co Ltd DINSTAR DAG1000 2000 Series FXS FXO Voice Gateway User Manual 4 5 8 ARP ARP brief introduction ARP is address resolution protocol After configuring ARP users can get physical address through device IP address Under TCP IP network environment each host is assigned a 32 bit IP addres
24. er Can use dynamic or static DNS server address Fill out an ID to describe a data VLAN group ID 0 used to management VLAN can t used to service Management 802 1Q VLAN peace configure Management Management 802 1p Priority 802 1 protocol to control network traffic priority VLAN 0 7 Priority from 0 7 IP address Can use dynamic or static IP address Management VLAN DNS server Can use dynamic or static DNS server address Note restart the device to take configuration effect 4 5 3 MAC Clone Routing mode MAC Clone This page provides the setting MAC address of WAN PC MAC Address BC AE C5 44 79 E9 Device WAC Address 00 1F D6 97 02 7D Restore Note The device mustrestart to take effect Figure 4 5 4 MAC Clone Interface More client in LAN have already can t share internet used the traditional gateway set law Because IP address binding in only a legitimate MAC address by ISP If the ISP s switch discovers illegal MAC address it will refuse the service The best way is MAC clone for MAC binding Most ADSL MODEM broadband router wireless router have this feature The principle of MAC address clone is deliberately exposed MAC address of bound computer to the ISP server and let the ISP server think that used only a single piece of computer in fact many computers in sharing the Internet This function used to prevent ISP limiting to share the Internet Note Restart device to take configuration effec
25. esponding extension number enable voice mail function in Elastix and set password As below 35 Dinstar Technologies Co Ltd DINSTAR DAG1000 2000 Series FXS FXO Voice Gateway User Manual Voicemail amp Directory Status Enabled w Voicemail Password 111111 Email Address Pager Email Address Email Attachment C yes Play CID yes Play Envelope yes Delete Voicemail C yes IMAP Username IMAP Password VM Options VM Context default VmX Locater Figure 4 8 4 Elastix Voicemail Configuration Interface 2 Check feature code in Elastix and change it as necessary Its default feature codes setting as below Voicemail Dial Voicemail My Voicemail Figure 4 8 5 Elastix Voicemail Setting SIP Parameter SUBSCRIBE for MWi Message Waiting Indicator Enable Voicemail User ID Figure4 8 6 Voice Mail Setting In SIP Parameter 3 Enable voice mail in DAG and Elastix will ask you to leave a message after ringing 15 seconds then Elastix will record and display your message 36 Dinstar Technologies Co Ltd DINSTAR DAG1000 2000 Series FXS FXO Voice Gateway User Manual Voicemail Ringtime Default 15 Direct Dial Voicemail Prefix Direct Dial to Voicemail message type Unavailable v Optional Voicemail Recording Gain Do Not Play please leave message after tone to caller a Figure 4 8 7 Voicemail Setting 4 DAG dial 200 then dial voicemail account and thenask password for Validat
26. ete one stage dialing Auto Dial delay time Delay time of FXO port send auto dial number e It specifies the policy for selecting port in a port group e Ascending the system always selects a port from the minimum number The preferential selection of the port can be realized through this mode Cyclic ascending when system selects ports Priority it always begin from the number next to the number selected last time if the maximum priority number is selected last time then the next number is the minimum priority number Port Select and move in cycles like this Descending when system selects ports priority it always begin to select from the maximum priority number Cyclic descending when system selects ports Priority it always begin from the number before to the number selected last time if the minimum priority number is selected last time then the next number is the maximum priority number and move in cycles like this Group ring all ports ringing at the same time Press extension number to decide which extension on Pick Up on Group the phone 4 9 2 IP Trunk A peer to peer VoIP call occurs when two VoIP phones communicate directly over IP without IP PBXs between them A peer to peer call can be initiated directly by dialing destination phone number in DAGs and also receiving incoming calls from other peer to peer gateway IP trunk is help to DAGs establish peer to peer call between DAGs and other VoIP pho
27. ge detect the connection status between device and SIP server Use Random Port Random SIP service ports for DAG Set Local SIP port Default SIP service port is 5060 25 Dinstar Technologies Co Ltd DINSTAR DAG1000 2000 Series FXS FXO Voice Gateway User Manual 4 7 Port Configuration Port parameters include Send gain receive gain primary display name etc Port Add Port Tx Gain Rx Gain Primary Display Name Primary SIP UserID Primary Authenticate ID Primary Authenticate Password secondary Display Name Secondary SIP User lb secondary Authenticate ID Secondary Authenticate Password Offhook Auto Dial Auto Dial Delay Time DND Do Not Disturb Enable Caller ID Enable Number for CFU Call Forwarding Unconditional Number for CFB Call Forwarding Busy Number for CFNRy Call Forwarding No Reply Call Waiting Enable Play Call Waiting Tone Enable Figure 4 7 1 Port configuration interface Port parameters introduce as follows It is use to control the volume of conversation Adjust TX gain will affect the Tx Gain end users voice size the default value is 0 Its value range from 10 10 dB It is use to control the volume of conversation Adjust RX gain will affect the Rx Gain end users voice size the default value is 0 Its value range from 10 10 dB Primary Secondary SIP Primary Secondary SIP account description Its purpose is so you can identify Primary Secondary User account
28. hen the device is uploading Figure 4 11 2 Firmware upload Configuration 52 Dinstar Technologies Co Ltd DINSTAR DAG1000 2000 Series FXS FXO Voice Gateway User Manual 4 11 3 Data Backup The process data backup 1 Click Data Backup 2 Click Backup to backup data to PC Data Backup Click Backup for download configuration file to your computer Figure 4 11 3 Data Backup Interface 4 11 4 Data Restore The processes of data restore 1 Click Data Restore 2 Browse file select data file 3 Click Restore and then import successfully the device will restart automatically Data Restore Send data file irom your computer to the device Configuration Figure 4 11 4 Data Restore Interface 4 11 5 Ping Test Send test data packets to IP check each other whether have response and statistical response time It is ping Used to test internet and analyzed network fault Application format Ping IP address It is used to check the network connectivity or network connection speed command Pinginstructions 1 Click ping test 53 Dinstar Technologies Co Ltd DINSTAR DAG1000 2000 Series FXS FXO Voice Gateway User Manual 2 Fill IP address or domain connected click start 3 Received a message indicates that network connection normal or network connected to a fault Ping Test Destination Number of Ping 1 100 Packet Size 56 1024 bytes Information
29. ill consider the extension as complete and it will try to send to SIP server Default value is 4 seconds gt Timeout for Answer Outgoing Call This timer set how long the caller party waiting when makes outgoing call on extension gt Timeout for answer Incoming call This timer set how long the phone sets ringing when get incoming call gt No RTP Detect This option is to disconnect call when there is no RTP received Default value is 90s Incoming call setting and Caller ID 29 Dinstar Technologies Co Ltd DINSTAR DAG1000 2000 Series FXS FXO Voice Gateway User Manual Incoming Call from PSTN Configuration by FXO Enable Detect CID send Original CID when Call from PSTN Enable Format of From field when CID is Available Displaw CID Format of From field when CID is Unavailable Display User ID CID Calling Number Name Calling Name FXO Keep Onhook until Callee Answered L Enable Play Hint to FXO Enable Allow Callto SIP Server without Registration Enable gt Configuration by FXO When the call from FXO interface users can be enable or disabled FXO allocation function FXO configuration function includes detect CID Send original CID Play hint to FXO gt Detect CID to enable caller ID detection for incoming calls The gateway has two modes Before ring and after ring Before ring the FXO port will detect CID first then ringing to the port It takes about few seconds to detect CID in generally
30. ion After that the user will hear voice message 4 8 4 Fax Parameter Fax introduction DAG fax parameter includes fax mode Fax sound detection party ECM Rate Fax Config Mode T38 d Tone Detection by Auto Je ECM Enable F Rate 14400 bps e Figure 4 8 8 Fax Parameter Configure Interface Fax parameter description Fax mode support T 38 T 30 Pass through Modem Adaptive Tone Detection by Fax sound detection mode Caller Callee Automatic ECM Fax error correction information The rate of sending and receiving 37 Dinstar Technologies Co Ltd DINSTAR DAG1000 2000 Series FXS FXO Voice Gateway User Manual 4 8 5 Digit Map Digit Map NOTE Length of Digit Map should not be more than 119 characters Figure 4 8 9Digit Map Gateway is collect digits dialed by user if received a number to be immediately report the efficiency is too low and a large number of take up network resources A reasonable method is concentration sending a message after receiving all number How to judge the gateway receiving all number is the difficulties of this method The solution is the call agent loading a Digit Map to gateway Digit Map includes a series figure characters when the dial up sequence and one received a character string matching it means the number has received neat Digital string contains characters allowed data0 9 letterA D letter T letter x and parts of each WK
31. l taking some other operating The typical application of hook flash is the telephone switchboard When need to transfer the call to other extension then Dinstar Technologies Co Ltd DINSTAR DAG1000 2000 Series FXS FXO Voice Gateway User Manual telephone hook flash to transfer the call CID Type There are DTMF and FSK General for the default Message Type The call display formats SDMF and MDMF General for the default After enable this configuration The DAG send caller to phone set before Send CID before Ringing o l pa o ringing otherwise the caller ID will display after ringing Delay of sending CID after Definite delay timer of caller ID while it set to send caller ID after ringing Ringing Its Default value 500ms l The time of no answer call transfer This time must less than call in no CFNRY Timeout answer overtime SLIC Setting Set the unit impedance Basic Parameters of FXO Call Progress Tone Timeout for Dialing As Timeout for Answer Outgoing Call 55 5 Timeout for Answer Incoming Call 55 5 No RTP Detected Enable Period without RTP Packet 5 gt Call Progress Tone Hear the dial tone when pick up the phone Choose the national standards from the drop down box Default is the United States gt Timeout for Dialing With the help of dialing timeout you can limit the time while users typing the digits from an extension If the timeout expire while the user is typing in the extension then DAG w
32. l name Calls from IP Trunk SIP Server any means any IP Caller number Prefix its length normally less or equal to caller number l which helps to matching routing exactly if caller number is 2001 the Caller Prefix l l caller prefix can be 200 or 2 any means match any caller number like bob1 29801 Called number Prefix its length normally less or equal to callednumber which helps to matching routing exactly if called number is Callee Prefix 008675526456659 the called prefix can be 0086755 or OU am means match any called number Calls to This call routing is routing to port or port group 47 Dinstar Technologies Co Ltd DINSTAR DAG1000 2000 Series FXS FXO Voice Gateway User Manual 4 9 5 Tel IP Tel Routing Tel IP Tel Routing Add Index Description Calls from Por PortGroup kd SIP Server NOTES any in Callee Prefix or Caller Prefix means wildcard string Figure 4 9 5 Tel IP Tel Parameters Configuration Routing priority 0 31 0 is the highest priority its purpose is so you can identify the routing with a meaningful name Calls From Tel IP call select port or port group Caller number Prefix its length normally less or equal to caller number which Caller Prefix helps to matching routing exactly if caller number is 2001 the caller prefix can be 200 or 2 any means match any caller number like bob1 29801 Called number Prefix its length normal
33. lect to RTP Mode in SDP when Call Holding l not receive and not send packet then doesn t play call waiting tone Enable this function users may use the business call IP IP to IP Call address on the phone 34 Dinstar Technologies Co Ltd DINSTAR DAG1000 2000 Series FXS FXO Voice Gateway User Manual URI Includes user phone SIP carries the information the system defaults not open Default is no it indicates the DAG accept incoming call from Only Accept Call from Server SIP server only Enable anonymous call anonymous will include in SIP Anonymous Call message l Enable this function reject all anonymous call Disable by Reject Anonymous Call default After hook flash flash event will report flash message to server Send Flash Event and server deal with this information as ending Dial Key Dial up use as a end descriptor RFC3262 defined an optional extension methods PRACK PRACK provisional ack Used to support the reliability of the temporary response Its function is to require the receiving partycontact with the third partythrough the use of supplied in the request in the Value of Refer To refers to Contact l l o address information Refer to field of SIP message fill in contact header Default is A QUERY Voice mail instructions Here DAG work with Elastixas the example introduces how voicemail work in DAG 1 DAG register to Elastix server Corr
34. ler A dials 87 then dials caller C s number and then or wait for 4 seconds 3 Caller A will hear the confirm tone Then A can hang up Note Call features enable must be set to Yes in web configuration page Caller A can place a call on hold and wait for one of three situations Dinstar Technologies Co Ltd DINSTAR DAG1000 2000 Series FXS FXO Voice Gateway User Manual 1 A quick confirmation tone similar to call waiting tone followed by a dial tone This indicates the transfer is successful At this point Caller A can either hand up or make another call 2 A quick busy tone followed by a restored call on supported platforms only This means the transferee has received a 4xx response for the INVITE and we will try to recover the call The busy tone is just to indicate to the transferor that the transfer has failed 3 Continuous busy tone The phone has timed out 2 4 2 Attended Transfer Attended transfer allowsusers to confirm the third party response and decide whether to answer the calls and then transfer this call to the third party Assume that Caller A and B are in conversation Caller A wants to Attend Transfer B to C 1 Caller A presses FLASH on the analog phone for dial tone 2 gt Dial Caller Ce number followed by or wait for 3 seconds 3 If Caller C answers the call Caller A and Caller C are in conversation Then A can hang up to complete transfer 4 If Caller C does not answer
35. ll be played between step 1 and step 2 Examples Dinstar Technologies Co Ltd DINSTAR DAG1000 2000 Series FXS FXO Voice Gateway User Manual If the target IP address is 192 168 0 160 the dialing convention is 47 then 192 168 0 160 Followed by pressing the key or wait 3 seconds Complete signaling interactive soon after he was called the unit can be heard ringing Note You cannot make direct IP calls between FXSO to FXS1 since they are using same IP It only supports the default destination port 5060 2 2 Call Hold Place a call on hold by pressing the flash button on the analog phone if the phone has that button Press the flash button again to release the previously held Caller and resume conversation If no flash button is available use hook flash toggle on off hook quickly You may drop a call using hook flash 2 3 Call Waiting Call waiting tone 3 short beeps indicates an incoming call if the call waiting feature is enabled Toggle between incoming call and current call by pressing the flash button First call is placed on hold Press the flash button to toggle between two active calls 2 4 Call Transfer 2 4 1Blind Transfer Blind transfer used to transfer call to the third party without inform caller Assume that call Caller A and B are in conversation A wants to Blind TransferB to C 1 Caller A presses FLASH on the analog phone to hear the dial tone 2 Cal
36. llowing figure 4 4 3 Data VLAN E Enable Data 802 10 VLAN ID 0 4095 Data 802 4P Priority 0 7 In this case data VLAN uses the default WAN interface Voice VLAN CT Enable Voice 802 10 VLAN ID 0 4095 Voice 802 1P Priority 0 7 Voice VLAN uses following separate IP interface Obtain an IP address automatically Use the following IP address IP Address subnet Mask Default Gateway Management VLAN CT Enable Management 802 10 VLAN ID 0 4095 Management 802 1P Priority 0 7 Management VLAN uses following separate IP interface Obtain an IP address automatically Use the following IP address IP Address subnet Mask Default Gateway Figure 4 5 3 VLAN parameter configuration Table 4 5 1VLAN parameter configuration Fill out an ID to describe a data VLAN group ID 0 used Data 802 1Q VLAN ID 0 4095 to management VLAN can t used to service Data VLAN configure 802 1 protocol to control network traffic priority Data 802 1p Priority 0 7 Priority from 0 7 Fill out an ID to describe a voice VLAN group ID 0 Voice VALN Voice 802 1Q VLAN ID 0 4095 used to management VLAN can t used to service configure 19 Dinstar Technologies Co Ltd DINSTAR DAG1000 2000 Series FXS FXO Voice Gateway User Manual 802 1 protocol to control network traffic priority Voice 802 1p Priority 0 7 Priority from 0 7 IP address Can use dynamic or static IP address Voice VLAN DNS Serv
37. ly less or equal to called number which helps to matching routing exactly if called number is 008675526456659 the called prefix can be 0086755 or 00 any means match any called number Calls to This call routing is routing to port port group IP trunk and SIP server Callee Prefix 48 Dinstar Technologies Co Ltd DINSTAR DAG1000 2000 Series FXS FXO Voice Gateway User Manual 4 10 Manipulation Configuration 4 10 1 IP Tel Callee ID ziel Callee Add Index ao o o Calls from IPTrunk Any Le SIP Server Caller Prefix PO Port Group Stripped Digits from Left stripped Digits from Right Prefix to Add Suffix to Add Number of Digits to Leave from Right NOTE any in Callee Prefix or Caller Prefix means wildcard string Figure 4 10 1 IP Tel Callee number configuration Calls From This call come from IP trunk or SIP server Caller number Prefix its length normally less or equal to caller number which helps to matching routing exactly if caller number Caller Prefix l is 2001 the caller prefix can be 200 or 2 any means match any caller number like bob1 29801 Called number Prefix its length normally less or equal to called number which helps to matching routing exactly if called number Callee Prefix is 008675526456659 the called prefix can be 0086755 or 00 any means match any called number 49 Dinstar Technologies Co Ltd DINSTAR
38. m e SIP Session Initiation Protocol e TCP Transmission Control Protocol e UDP User Datagram Protocol e RTP Real Time Protocol e PPPOE point to point protocol over Ethernet e VLAN Virtual Local Area Network e ARP Address Resolution Protocol e CID Caller Identity e DND Do NOT Disturb e DTMF Dual Tone Multi Frequency e NTP Network Time Protocol e DMZ Demilitarized Zone e STUN Simple Traversal of UDP over NAT e PSTN Public Switched Telephone Network 57 Dinstar Technologies Co Ltd
39. n Figure 4 8 10 Feature Code Configuration Interface 40 Dinstar Technologies Co Ltd DINSTAR Inquire LAN port IP address Inquire WAN port IP address Inquire Phone Number Setting IP Mode Network Work Mode Configure IP Address Network subnet mask configure Network Gateway Configure Renew DHCP Access Web by Wan in Rout Mode Reset Factory Restart Device Call onhold offhold Call by IP Call Waiting Activate Call Waiting Deactivate Blind Transfer Call Forward Unconditional Activate Call Forward Unconditional Deactivate Call Forward Busy Activate Call Forward Busy Deactivate Call Forward No Reply Activate Call Forward No Reply Deactivate Do Not Disturb Activate Do Not Disturb Deactivate Dial Voicemail kA Dinstar Technologies Co Ltd DAG1000 2000 Series FXS FXO Voice Gateway User Manual Dial 158 to obtain device WAN port IP address Dial 159 to obtain device WAN port IP address Dial 114 to obtain port account 150 0 means pppmodem 150 1 means static IP 150 2 means obtain IP address by DHCP 150 3 means Pppoe 157 0 set network work mode to routing mode 157 1 set network work mode to bridge mode 152 IP set gateway IP address 153 subnet mask set gateway subnet mask 156 gateway IP set gateway 193 set dynamic IP again Allow access web through WAN port 160 1 don t allow access web through WAN port 160 0 166 000000 reset facto
40. nd the right configuration interface Choose navigation tree in order to entry into the configuration interface 11 Dinstar Technologies Co Ltd DINSTAR DAG1000 2000 Series FXS FXO Voice Gateway User Manual Status amp Statistics Quick Setup Wizard Network Local Network VLAN MAC Clone DHCP Server DMZ Host Foward Rule Static Route ARP Config SIP Server Port Advanced Call amp Routing Manipulation Maintenance Figure 4 2 1 Navigation Tree When device is in bridge mode navigation tree won t display routing configuration items and the following DHCP service DMZ host forward rules and static routing and ARP etc 4 3 State and Statistics 4 3 1 System Information System information interface shows the run information as following figure 4 3 1 below Dinstar Technologies Co Ltd 12 DINSTAR DAG1000 2000 Series FXS FXO Voice Gateway User Manual System Information MAC Address 00 1F D6 A0 01 04 Network Mode Bridge IP Address 172 16 66 3 255 255 0 0 Static 172 16 1 1 DNS Server 202 96 128 68 202 96 134 133 System Uptime T h 10m 50s NTP Status Succeed Network Traffic Stat Received 1912835244 bytes Sent 318891 bytes DAG1000 4540 Rev 2 11 08 07 Beta 1 PCB 23 1 LOGIC 0 BIOS 1 Built on Apr 18 2014 Version 13 36 18 Figure 4 3 1 1 System Information System information Router mode as follow Table 4 3 1 System Information Description MAC address
41. nding CID after Ringing 500 ms Lu UI CFNRy Timeout SLIC Setting 600 Ohm Figure 4 8 1 FXS FXO Parameters Configuration Interface FXS FXO parameters description Hear the dial tone when pick up the phone Choose the national standards Call Process Tone l l from the drop down box Default is the United States With the help of dialing timeout you can limit the time while users typing the digits from an extension If the timeout expire while the user is typing in Timeout for dialing l l l l the extension then DAG will consider the extension as complete and it will try to send to SIP server Default value is 4 seconds Timeout for This timer set how long the caller party waiting when makes outgoing call answer Outgoing call on extension Timeout for o Ea l l l This timer set how long the phone sets ringing when get incoming call answer Incoming call Life Line when Registration Under device are not registered circumstance call inbound directly from Failed corresponding FXO port Send Polarity Reversal Enable polarity reversal to billing A protruding button where putting the receiver boards called Flash Always press is hang up pick up the receiver the fork lift machine from reed called by hand clap called Hook flash Hook flash is a process that put the flash Detect Hook flash fast by pressing and let go In essence is to cut off the dc access about 80 to 200 ms Then switches don t think it s hang on but keep the cal
42. nes IP trunk will be used in routing configuration 45 Dinstar Technologies Co Ltd DINSTAR DAG1000 2000 Series FXS FXO Voice Gateway User Manual IP Trunk Add Index Description Remote Address Remote Port Heartbeat Figure 4 9 2 IP Trunk Configuration Interface Index IP trunk number it is range from 0 to 63 o The description of IP trunk its purpose is so you can identify the IP trunk with a Description meaningful name Remote Address Peer IP address or domain name Remote Port Peer SIP port Heartbeat Default is disable if enable DAG will send OPTION to peer device 4 9 3 Routing Configuration Figure 4 9 3 Routing Parameter Configuration Interface Routing Parameter Calls from IP Routing before Manipulation Calls from Analog Line Routing before Manipulation This option determines the following routing of call take effect before or after manipulation 46 Dinstar Technologies Co Ltd DINSTAR DAG1000 2000 Series FXS FXO Voice Gateway User Manual 4 9 4IP Tel Routing IP gt Tel Routing Add Index 31 Calls from IPTrunk Any SIP Server Caller Pretix Pd Callee Prefix Calls to Po oe Port Group NOTES any in Callee Prefix or Caller Prefix means wildcard string Figure 4 9 4 IP Tel Routing Parameter Routing priority 0 31 0 is the highest priority o its purpose is so you can identify theIPO gt Tel routing with a Description l meaningfu
43. oRFC3551 Packetization Time Voice package time Default is disable if enable according to the current noise environment dynamically adjust Slience Suppression mute inhibit threshold thus in the user in silent state stop transmission background noise bag and save about VoIP bandwidth In the low 33 Dinstar Technologies Co Ltd bandwidth environment can DINSTAR DAG1000 2000 Series FXS FXO Voice Gateway User Manual reduce the network congestion greatly improving VoIP call effect 4 8 3 SIP Parameter SIP Parameter SUBSCRIBE for MWi Message Waiting Indicator Voicemail UserID RTP Mode in SOP when Call Holding IP to IP Call URI includes user phone Only Accept Calls from Server Anonymous Call Reject Anonymous Call send Flash Event GE as Ending Dial Key PRACK Value of Refer To refers to Contact Domain Query Type Domain Re resolution Inteval 0 means disable IN T2 T4 Max Timeout Heartbeat Interval 1 360085 Figure 4 8 3 SIP Parameter Configuration Interface SIP parameter description E Enable Sendonly Enable Enable Enable Enable Enable Enable Enable Enable Enable A Query Voicemail message indicator it is to be realized in the way SUBSCRIBE for MWI of NOTIFY Voicemail User ID Access code to voicemail box When call come into holding if select to receive and not send packet then the local can hear call waiting tone If se
44. r convert to 12VDC power Power parameters Input 100 240VAC 50 60Hz Output 12VDC DAG2000 8S80 can be installed in the 19 inch frame and adopts AC power supply Notes Because power adapter interface is different in different country please confirm the interface standard with us before shipment 1 4 Network Applications All over the world IP LAN DAG1000 80 FXO lines FXO olP access gateway DAG1000 8S lt IP Network O E Be es FXS PBX DAG1000 4S VolP access atewa S i amp Ke p Phone Phone Phone Phone Phone Phone Phone Phone Masi Figure 4 1 Network Applications Dinstar Technologies Co Ltd DINSTAR DAG1000 2000 Series FXS FXO Voice Gateway User Manual 1 5 Functions and Features 1 5 1Protocol standard supported e SIP V2 0 RFC 3261 3262 3264 SDP RFC 2327 e REFER RFC 3515 e RTP RTCP RFC 1889 1890 e STUN RFC 3489 e ARP RARP RFC 826 903 SNTP RFC 2030 e DHCP PPPOoE TFTP HTTP HTTPS e DNS DNS SRV RFC 1706 RFC 2782 e VLAN 802 1P 802 1Q e Diff Serve 1 5 2 Voice and Fax parameters e G 711A U law G 723 1 G 729AB e Comfortable Noise Generation CNG e Voice Activity Detection VAD e Echo Cancellation G 168 Adaptive Dynamic Jitter Buffer e Voice and fax gain control e Hook flash Detect e 1 38 Pass through DTMF Mode Signal RFC2833 INBAND 1 5 3 Supplementary service Busy tone detec
45. ry 111 restart device When call process dial into call hold Recovery the call through hook flash or Directly dial the end user IP to call 51 enable call waiting function 50 forbid call waiting function If the call transfer to 801 first hook flash and then dial the 87 801 72 phone number transfer the call from the phone number 73 forbid call forward unconditional 90 forward busy number 91 forbid call forward busy 92 forward no reply number 93 close this function 78 enable DND function 79 close DND function 200 visit voice mail box DINSTAR DAG1000 2000 Series FXS FXO Voice Gateway User Manual Note Private services are open by default 4 8 7 System Parameter System parameters include STUN NTP Provision WEB parameter Telnet 1 STUN STUN Simple Traversal of UDP over NATs is a network protocol It allows users back of NAT find their own public network address NAT type and internet end port have been bound by NAT for a local port Two back of NAT router devices established UDP communication through this information STUN doesn t support TCP connection and H 323 2 NTP Network Time Protocol NTP is a computer time synchronization protocol System parameter configuration interface as follow System Parameter STUN E Enable NTP Enable Primary NTF Server Address US poolLntp org Primary NTP Server Port secondary NTF Server Address Seconda
46. ry NTP Server Port SYN Interval Time Zone Daily Reboot Reboot Time WEB Parameter WEB Port Access WEB by WAN Telnet Parameter Telnet Port Figure 4 8 11System Configuration Interface 42 Dinstar Technologies Co Ltd DINSTAR STUN Server Address STUN Server Port Primary NTP server address Primary NTP server port Secondary NTP server address Secondary NTP server port SYN Interval Time Zone Reboot Time WEB Port Access Web by WAN Telnet Port 4 9 Call amp Routing 4 9 1 Port Group DAG1000 2000 Series FXS FXO Voice Gateway User Manual STUN server IP address STUN server port Primary NTP server IP address system default is us pool ntp org Default is 123 Default is 18 145 0 30 Default is 123 Every certain time synchronization gateway time the system default every 3600 s synchronous once Time zone can be chosen System default the United States central time Chicago Set a restart time for device the device will reboot at this time Gateway web port default is 80 Enable or disable accessing web by WAN Telnet service port default is 23 Port group parameter include Index description etc Port group configure interface as follow Dinstar Technologies Co Ltd 43 DINSTAR DAG1000 2000 Series FXS FXO Voice Gateway User Manual Por Group Add Index Description Primary Display Name Primary SIP User ID Primary Authenticate ID Primary Authenticate Passwor
47. s But the message transmission needs to know the purpose the physical address of the party ARP is a tool that converts IP address into MAC address ARP configuration interface as follows 8 Static Dynamic Figure 4 5 9 ARP Parameters 4 6 SIP Server SIP server introduction 1 SIP server is the main component of VoIP network and responsible for establishing all the SIP phone calls SIP server also called SIP proxy server or registered server IPPBX and the soft switch can act as SIP server role 2 Usually SIP server does not participate in the media process In SIP network the media always using end to end to hand the consultation In some particular situation or business processing such as Music On Old SIP server will actively participate in the media negotiation Simple SIP server is responsible only for establishment maintenance and cleaning conversation don t interfere in call While relatively complex SIP server also called SIP PBX It not only provides the basic call and basic conversational support also offer plenty of business such as Presence Find me Music On Hold 3 SIP server based on Linux platform such as OpenSER sipXecx VoS Mera etc 4 SIP server based on windows platform such as miniSipServer Brekeke VoIPswitch etc 24 Dinstar Technologies Co Ltd DINSTAR DAG1000 2000 Series FXS FXO Voice Gateway User Manual 5 Carrier grade soft switch platform such as Cisco Huawei Zteetc
48. t 20 Dinstar Technologies Co Ltd DINSTAR DAG1000 2000 Series FXS FXO Voice Gateway User Manual 4 5 4 DHCP Server Routing mode Under route mode DAG network part as a small router to configure DHCP service that DAG as a DHCP server in network Start and end address of address pool determine the range of IP address automatically assigned to other devices e IP Expire Time means use time of assigned IP address More than the lease time if the IP address is not used by network equipment IP address will be recovered e Subnet mask gateway DNS and other information configured by DHCP protocol Configuration interface as figure 4 5 5 DHCP Server Config DHCP Server Enable IP Pool Starting Address 192 166 771 100 IP Pool Ending Address 192 168 11 199 IP Expire Time Subnet Mask Optional 255 255 255 0 Default Gateway Optional 192 168 11 77 Primary ONS Server Optional 202 96 126 668 secondary ONS Server Optional 202 96 134 133 Note The device must restart to take effect Figure 4 5 5 DHCP Configuration Interface Note When configure start and end IP address subnet mask and gateway please set the same segment with LAN port Otherwise device will not work normally After configuration restart device configuration validation 4 5 5 DMZ Host Routing mode DMZ Demilitarized Zone connect web e mail etc server allowed external to access to this area Make the internal network located the back of the
49. t group registration information 4 3 3 TCP UDP Statistics TCP UDP Traffic Refresh Figure 4 3 3 TCP UDP Statistics Information Figure 4 3 3 shows TCP sending and receiving UDP sending and receiving packets of Statistical information since the device launched 4 3 4 RTP Session Statistics RTP Session Figure 4 3 4 RTP Session Statistics Figure 4 3 4 display real time RTP conversation flow data information includes Port voice codec packet period local port peer IP peer port sent packets receive packets lost packets jitter and duration 14 Dinstar Technologies Co Ltd DINSTAR DAG1000 2000 Series FXS FXO Voice Gateway User Manual 4 4 Quick Setup Wizard Quick configuration guide will guide users to configure the device step by step Users only need to configure network SIP server and sip port in quick setup wizard Basically after these three steps users are able to make voice call through device 4 5 Network Configuration 4 5 1 Local Network DAG FXS FXO hybrid gateway has two kinds of work mode route and bridge When DAG is set route mode the DAG will work as small router and NAT function has enabled In this situation WAN port is normally connect to uplink router switch or ADSL MODEM LAN port used to connect local computer or other network device such as Ethernet switches Hubs etc When DAG is set bridge mode WAN and LAN port are the same The DAG just work as two ports or four por
50. the standard file information Syslog agreement belongs to a kind of master slave agreement Syslog sender will sent a small text information less than 1024 bytes to syslog the receiver The receiver are syslogd syslog daemon or syslog server Syslog message can be transferred by TCP UDP 51 Dinstar Technologies Co Ltd DINSTAR DAG1000 2000 Series FXS FXO Voice Gateway User Manual Syslog level e none Used to misarrange e debug Not including function conditions or the question of other information e notice importance common conditions e warning Early warning information e error Stop error conditions of tools or some part of the realization of the function subsystem Syslog Parameter Syslog E Enable Figure 4 11 1 Syslog Parameter Configuration Enable send CDR and then send communication information to syslog server 4 11 2 Firmware Upload The process of firmware upload 1 Click Firmware Upload 2 Browse files and choose the loading program Name the file extension Idf 3 Click Upload the upload process will last about 60s and device can automatically restart after uploading The firmware update process don t shut off the power Firmware Upload send ld file from your computer to the device Software SCC EE ee eat Voice File JEM SRI Notes 1 The upload process will last about 60s 2 The device will restart automatically after upload 3 Do not shut down w
51. ting tone caller will hear special tone 4 8 Advanced 4 8 1 FXS FXO parameters FXS characteristic parameters include Call progress Tone Timeout for Dialing Send Polarity Reversal etc FXO full name is Foreign Exchange Office It is a kind of voice interface and a trunk connected between central exchange switches and telephone exchange system To central office speaking it simulates a PABX extension and can realize connection among common phone and a multiplexer It also is FXO interface connected with SPC exchanges FXO as ordinary telephone interface and need to remote provide current FXO may connect company s internal PBX service extension and the telecom outside generally speaking FXO is a telephone So just lead a inside to FXO port from company s internal or directly line a straight up in FXO from the telecom FXO parameters include Call progress Tone Timeout for Dialing Send Polarity Reversal 27 Dinstar Technologies Co Ltd DINSTAR DAG1000 2000 Series FXS FXO Voice Gateway User Manual etc Configuration interface as follow Call Progress Tone USA aids Timeout for Dialing Timeout for Answer Outgoing Call Timeout for Answertincoming Call Life Line when Registration Failed Enable FAS Parameter send Polarity Reversal Detect Hook Flash SI Mm m St Gi D Di sf D o Min Time ho Ims Max Time 400 ms CID Type 7 Message Type MDME sw send CID before Ringing JEnable Delay of Se
52. tion No current take out stitches detection Voice interrupted detection e One stage dialing Two stage dialing PSTN exterior ports polling Polarity Reversal FAS Fake billing correction DC AC impedance config Calls detection Bellcore Type 1 amp 2 ETSI DTMF Dinstar Technologies Co Ltd DINSTAR DAG1000 2000 Series FXS FXO Voice Gateway User Manual Direct IP Call Primary and secondary SIP account e 32 inbound outbound routing Number manipulation Dial plan set Life line 2 Basic Operations 2 1 Phone Call 2 1 1 Phone or Extension Number 1 Dial the number directly and wait for 3 seconds Default Wo dial timeout 2 gt Dial the number directly and press 2 1 2 Direct IP Calls DAG series device with FXS port allow two parties directly call through IP address The user need only a simulation with the FXS port unit equipment linked together and set up calls not registered Elements necessary to completing a direct IP call 1 Both DAG serial and other VoIP Device have public IP addresses 2 Both DAG serial and other VoIP Device are on the same LAN using private IP addresses 3 Both DAG serial and other VoIP Device can be connected through a router using public or private IP addresses with necessary port forwarding or DMZ Operation Process 1 Pick up the analog phone then dial 47 2 Enter the target IP address Note No dial tone wi
53. ts Ethernet switch When it set to bridge mode only need to configure WAN port IP address and DNS If set to route mode default LAN port IP will display and it can be change by users Note DAG2000 8S80 just supports bridge mode only DAG1000 4s40 supports bridge and route mode Configuration of Route mode 15 Dinstar Technologies Co Ltd DINSTAR DAG1000 2000 Series FXS FXO Voice Gateway User Manual Local Network Network Mode Route Bridge WAN Port Link Speed amp Duplex Auto Detect Le Obtain an IP address automatically Use the following IP address IP Address subnet Mask Default Gateway PPPoE Account Password Service Name LAN Port Link Speed amp Duplex Auto Detect e IP Address 192 168 11 1 subnet Mask DNS Server Obtain DNS server address automatically Use the following DNS server address Primary ONS Server secondary DNS Server Figure 4 5 1Route Mode Configuration of Bridge mode 16 Dinstar Technologies Co Ltd DINSTAR DAG1000 2000 Series FXS FXO Voice Gateway User Manual Local Network Network Mode Route Bridge Network Configuration Link Speed amp Duplex Auto Detect Obtain an IP address automatically Si Use the following IP address IP Address subnet Mask Default Gateway PPPoE Account Password service Name DNS Server Obtain DNS server address automatically Use the following DNS server address Primary DNS Server Secondary ONS Server Note
Download Pdf Manuals
Related Search
Related Contents
iA5 IB (Intl French) 060111 Sony CDX-CA400 User's Manual NLH165-LSC(F)_IM ed16 Bamix Mono 140 ELM3311 ELM3711 Copyright © All rights reserved.
Failed to retrieve file