Firedome® AX Series Helmets User Manual
Contents
1. Firedome AX Series Helmets a pullar d User Manual Get a Custom Fit with the U Fit System ESS Congratulations Your helmet was designed with the U Fit System offering 12 custom comfort settings Follow the instructions below to adjust the ride and balance of your helmet 1 Try on your helmet and check the initial balance fit and comfort by rotating your head 2 Remove the Ear Neck Protector to better see how to adjust the back of the helmet 3 Pop the gray colored U Channel Figure 1 away from the black inner liner There is one U Channel in the front of the helmet and one in the back of the helmet 4 You can tailor the fit by adjusting the tabs which control ride height and posts which control forward backward level balance 5 Adjust the ride of your helmet There are three tab positions on the U Channel A B and C Each of the tab positions affects the location of the ratchet by approximately one inch For the lowest ride on your head position the tabs to A For a higher ride position the tabs to B or C 6 Adjust the balance of your helmet There are two post positions 1 and 2 on the gray U Channel Change the post position to adjust helmet balance 7 Next try the helmet back on your head to see if the adjustments to the back of the helmet were helpful You may want to make another round of adjustments as described above to maximize the balance and fit Typi2. cally firefighters don t need to adjust the front of the helmet If however the adjustments to the rear of the helmet don t meet your needs you can work on the front of the helmet by first removing the browpad As with the back of the helmet you can adjust the height and post position on the U Channel piece Keep in mind that the front of the helmet is a key interface to the SCBA and most people prefer position C 8 Lastly when finished your adjustments re install the Ear Neck Protector and Browpad using your fingers to smooth the surfaces to avoid bunching To size the Sure Lock ratchet headband 1 Turn the ratchet knob counterclockwise until headband is at largest size Figure 3 ve eae 2 Place the helmet on your head and turn ratchet knob clockwise until headband is snug and comfortable e To raise or lower faceshield U Channel forward backward balance 1 Release tension knobs found on both sides of the helmet off of Tab postitions are 2 Tighten knobs once faceshield is in desired position pe UL P he ee lt lt oo quarter tm tabs NOTES SP ranean e Performance properties of NFPA 1971 2007 cannot be tested by users in the field Se c 4 lower on your head e NFPA 1500 Standard on Fire Department Occupational Safety and Health Program requires members who engage in or are exposed to the hazards of proximity firefighting shall be provided with and shall use a protective ensemble that shall meet the applicabl
3. e helmet shell e Secure snap tabs around faceshield mounting brackets e Pivot faceshield to ensure no snagging of the helmet cover Aluminized Shroud Installation e Begin at rear of the helmet and snap shroud to the helmet cover e Make certain that chinstrap is hanging inside the shroud after snapping to helmet cover A WARNING Read all instructions and warnings before wearing this helmet Performance properties of NFPA 1971 2007 cannot be tested by users in the field After removal from the wearer the helmet should be inspected for damage and soiling after each use The helmet should be adjusted by means of the adjustment points provided to permit a proper fit that does not interfere with the SCBA while in use These adjustments should be done prior to actual fire fighting activities Helmets damaged or deteriorated beyond economical repair should be removed from service Failure to follow these instructions could result in death or serious injury Pre Use Information Marking Recommendation and Restrictions Use only accessory equipment of the type included in the original helmet or approved by Bullard Using unauthorized accessories may dramatically change the performance of the helmet All helmet markings e g front identification shields title tapes decals retro reflective trim etc must either be supplied by a Bullard authorized fire service distributor or authorized for use in writing by Bullard All helmet acces
4. e possibility of such damages ANY IMPLIED WARRANTIES INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED IN DURATION TO TWO 2 YEARS FROM THE DATE OF MANUFACTURE OF THIS PRODUCT Some states do not allow the exclusion or limitation of incidental or consequential damages or allow limitations on how long an implied warranty lasts so the above limitations or exclusion may not apply to you This warranty gives you specific legal rights and you may have other rights which vary from state to state RETURN AUTHORIZATIONS Contact Sales Support to obtain written permission to return any product Material returned for credit will be subject to factory inspection Current products or products under warranty will be subject to a rehandling charge less original freight charge Obsolete or special order products cannot be returned without written permission Replacement Parts for AX Series Helmets CATALOG NUMBER DESCRIPTION R144 Nomex chin strap with quick release buckle and postman s slide fastener R151 Faceshield mounting hardware kit R340 6 gold coated faceshield R921 Replacement inner crown system for FX and PX Includes inner shell Sure Lock ratchet headband brow pad crown pad urethane impact liner 6 point nylon crown strap assembly and velcro strips R941 Replacement inner crown system for FX and PX Includes inner shell Sure Lock ratchet headband brow pad crown pad ure
5. e requirements of NFPA 1971 Standard on Protective Ensembles for Structural Fire Fighting and Proximity Fire Fighting e The protective ensemble must be used by members only under direct supervision of their fire department or employer in a manner consistent with OSHA 29 CFR 1910 132 General Requirements of Subpart I Personal Protective Equipment Figure 1 e For information on NFPA 1951 Standard on Selection Care and Maintenance and basic cleaning and inspection guidelines visit www bullard com trainonline A WARNING Read all instructions and warnings before wearing this helmet Only the end user may separate this manual from the element Manual must be removed prior to putting the helmet into service After removal from the wearer the helmet should be inspected for damage and soiling after each use The helmet should be adjusted by means of the adjustment points provided to permit a proper fit that does not interfere with the SCBA while in use These adjustments should be done prior to actual structural fire fighting activities Helmets damaged or deteriorated beyond economical repair should be removed from service Failure to follow these instructions could cause death or serious injury Instructions for Installing Aluminized Helmet Cover and Shroud Aluminized Helmet Cover Installation e Insert D ring on helmet shell through slot in helmet cover e Beginning at rear D ring pull cover over helmet shell and over the outside edge of th
6. ental degradation replace the shell and or suspension immediately If the helmet has sustained a forcible blow impact it must be replaced even if there is no visible damage Failure to observe these warnings could result in death or serious injury Firedome helmet model AX meets or exceeds all performance specifications under NFPA 1971 2007 MANAGEMENT o NFPA CERT MOD 2008 Bullard All rights reserved Bullard Firedome Sure Lock and Hard Boiled are registered trademarks Americas Europe Asia Pacific of Bullard E D Bullard Company Bullard GmbH Bullard Asia Pacific Pte Ltd Nomex and Kevlar are registered trademarks of E I du Pont de Nemours 1898 Safety Way Cynthiana KY 41031 9303 Lilienthalstrasse 12 LHK Building amp Company PBI is a registered trademark of Celanese Corporation Toll free 877 BULLARD 285 5273 Tel 859 234 6616 Fax 859 234 8987 www bullard com 53424 Remagen Germany www bullardextrem com 701 Sims Drive 04 03 Singapore 387383 Tel 49 2642 999980 Fax 49 2642 9999829 Tel 65 6745 0556 Fax 65 6745 5 www bullard com U S Patent No 5 150 479 6024405660G 1108
7. sories e g flashlight brackets communications head sets etc must be either supplied by a Bullard authorized fire service distributor or authorized for use in writing by Bullard Cleaning Remove shroud and helmet cover headband and crown straps Clean inner and outer shells with mild soap or detergent Wash the ear neck protector headband brow pad crown pad and crown straps in warm soapy water and air dry at room temperature Clean faceshields with mild detergent rinse thoroughly with clean water and dry with a soft cloth Users should not wear helmets that are not thoroughly cleaned and dried Contamination and Decontamination Special precautions must be taken if your protective helmet becomes contaminated with chemical or biological hazardous materials The guidance for these precautions should be coordinated with the appropriate local state and federal authorities having jurisdiction for hazardous materials HAZMAT Contaminated helmet ensembles should be isolated contaminate s identified and bodily contact should be avoided Avoid spreading the contamination to interior spaces of buildings or vehicles any living quarters or personal belongings If possible seal the contaminated ensemble in a leak proof sealable air tight container Disposal should be done in adherence to local state and federal laws If the helmet is to be reused it MUST be decontaminated before reuse Decontamination should be performed using procedures es
8. tablished by decontamination professionals that will remove contaminate s while minimizing damage or compromise to the helmet Failure to do so could result in increased risk of injury illness disease or death CAUTION Do not use solvents or paint thinners on Firedome helmets as they could permanently mar surfaces or degrade the protective properties of helmet components Touch up painting on composite outer shells can be done with Bullard approved paints Failure to follow these instructions could result in damage to the helmet aa Sullard Two Year Limited Warranty Bullard warrants to the original purchaser that the AX Series helmet is free of defects in materials and workmanship under normal use and service for a period of two 2 years from the date of manufacture The Bullard obligation under this warranty is limited to repairing or replacing articles that are returned within the warranty period shown to be defective after inspection by Bullard and subject to the following limitations e Helmet must be returned to Bullard with shipping charges prepaid e Helmet must not be altered from its original factory configuration e Helmet must not have been misused subjected to negligence or damaged in transport In no event shall Bullard be responsible for damages loss of use or other indirect incidental consequential or special costs expenses or damages incurred by the purchaser notwithstanding that Bullard has been advised of th
9. thane impact liner 6 point Nomex crown strap assembly and hook and loop strips A R112 Nylon crown straps with crown pad A R113 Nomex crown straps with crown pad B R637 Sure Lock ratchet headband C R635 Brow pad D R628 Ratchet height adjuster E R636 Crown pad CATALOG NUMBER DESCRIPTION Also available not pictured R260 Aluminized Helmet cover R261 Aluminized Helmet cover UST only R757 Aluminized shroud R758 Aluminized shroud R759 Aluminized shroud R760 Aluminized shroud R761 Aluminized air bottle cover Colors AX Series helmets are available in seven standard colors white red black yellow blue orange and lime yellow WARNING AX Series helmets are constructed with high quality materials and workmanship They are engineered to provide limited protection against head injuries when properly adjusted for fit and when worn by firefighters during normal fire fighting activities They are not designed for direct contact with flames or molten metal or for protection against hazardous chemicals biological or radiological agents Contact of these fire helmets with live wires should be avoided NEVER ALTER OR MODIFY the helmet s design or construction without explicit written instructions from Bullard Store Firedome helmets in a cool dry place away from direct sunlight Inspect your helmet and suspension system regularly regardless of how often it is used If you notice any sign of wear damage abuse or environm
Download Pdf Manuals
Related Search