Home

User Manual - CNET Content Solutions

1. 20 C to 60 C Operating humidity 8 80 non condensing Storage humidity 5 95 non condensing Operating altitude 3000 m Storage altitude 7500 m In dark reading room conditions 0 lux 55 Nio 3MP Product acronym E 3620 MA Screen technology TFT AM LCD Dual Domain IPS Active screen size diagonal 528 mm 20 8 Active screen size H x V 424 x 318 mm 16 7 x 12 5 56 Aspect ratio H V 4 3 Resolution 3MP 2048 x 1536 Pixel pitch 0 207 mm Color imaging No Gray imaging Yes Number of grayscales LUT in LUT out 1024 grey levels 10 10 Viewing angle H V 170 Uniform Luminance Yes Technology ULT Per Pixel Uniformity PPU No Ambient Light No Compensation ALC Backlight Output Yes Stabilization BLOS I Guard No Maximum luminance 1000 cd m2 DICOM calibrated 500 cd m luminance ULT off Contrast ratio typical 900 1 Response time Tr Tf 50 ms Scanning frequency H V 30 124 kHz 50 85 Hz i Housing color Gray Video input signals DVI D Dual Link USB ports 1 upstream 2 downstream USB standard 1 1 Power requirements 100 240V nominal Power consumption 54W nominal Power save mode Yes Power management DVI DMPM Dot clock 280 MHz OSD languages English Dimensions with stand W x H x D
2. 3 Push the control wheel once more to confirm and switch to stand by 4 The LED turns orange Push twice Figure 17 Location of the control wheel 5 When the display is in stand by press the control wheel shortly to switch it back on Locking and unlocking user controls The User Controls function allows to disable or enable the control wheel functions The procedure is slightly different depending on the type of display When user controls are disabled you cannot display and use the on screen display TO DISABLE USER CONTROLS ON E 3620 AND MDNG 5121 1 Rotate the control wheel to display the on screen display The Main Menu appears 2 Rotate the control wheel to select Settings 23 24 5 6 Press the control wheel to enter the Settings menu SETTINGS DPMS On Power LED On User Controls On EXIT Figure 18 Settings menu example Rotate the control wheel to select User Controls Press the control wheel to switch from On to Off Exit the menus TO DISABLE USER CONTROLS ON MDNC 2121 MDNC 3121 MDNG 2121 AND MDNG 6121 1 Rotate the control wheel to display the on screen display The Main Menu appears Rotate the control wheel to select Settings Press the control wheel to enter the Settings menu SETTINGS DPMS On Power LED On User Controls On EXIT Figure 19 Settings menu example Rotate the control wheel to select User Controls Press the
3. Dimensions with stand W xH xD Portrait 385 x 525 585 x 250 mm Landscape 485 x 475 535 x 250 mm Dimensions w o stand W Portrait 385 x 485 x 115 mm xHxD Landscape 485 x 385 x 115 mm Dimensions packaged Wx 500 x 320 x 675 mm H x D Net weight with stand 13 kg Net weight w o stand 9 kg Net weight packaged with 15 kg stand Net weight packaged w o NA stand Height adjustment range 60 mm Tilt 5 30 Swivel 45 45 Pivot 90 Mounting standard VESA 100 mm Te S Screen protection Protective non reflective PMMA cover Recommended modalities CT MR US DR CR NM Film Certifications BSMI CCC GB4943 2001 GB9254 2008 GB17625 1 2003 DEMKO EN60601 1 1990 A1 1993 A2 1995 A13 1996 IEC 60601 1 1988 A1 1991 A2 1995 2nd edition UL 60601 1 1st edition 2006 04 26 CAN CSA C22 2 No 601 1 M90 2005 FDAS10K RoHs MDD WEEE CE 0120 VCCI FCC Class B KETI Supplied accessories User Guide Quick Installation Sheet Video cable DVI Dual Link Mains cables UK European CEBEC KEMA USA UL CSA adaptor plug NEMA 5 15P Chinese CCC USB 2 0 cable External power supply Optional accessories A QA software MediCal QAWeb Unit per pallet A Pallet dimensions A Warranty 5 years Operating temperature 0 C to 40 C 15 C to 35 C within specs Storage temperatu
4. Dimensions with stand W x H x D Portrait 385 x 525 585 x 250 mm Landscape 485 x 475 535 x 250 mm Dimensions w o stand W xH xD Portrait 385 x 485 x 115 mm Landscape 485 x 385 x 115 mm Dimensions packaged W x H x D 500 x 675 x 320 mm Net weight with stand 12 2 kg Net weight w o stand 8 14 kg Net weight packaged with 17 19 kg stand Net weight packaged w o 13 15 kg stand Height adjustment range 60 mm Tilt 5 30 54 ie Swivel 45 45 Pivot 90 Mounting standard VESA 100 mm Screen protection Protective non reflective PMMA cover Recommended modalities CT MR US DR CR NM Film Certifications BSMI CCC GB4943 2001 GB9254 1998 GB9254 2008 GB17625 1 2003 DEMKO EN60601 1 1990 A1 1993 A2 1995 IEC 60601 1 1998 A1 91 A2 95 UL 60601 1 1st edition CAN CSA CS22 2 No 601 1 M90 FDA510K RoHs MDD WEEE CE 0120 VCCI FCC Class B KET Supplied accessories User Guide Quick Installation Sheet Video cable DVI Dual Link Mains cables UK European CEBEC KEMA USA UL CSA adaptor plug NEMA 5 15P Chinese CCC USB 2 0 cable External power supply Optional accessories A QA software MediCal QAWeb Unit per pallet A Pallet dimensions A Warranty 5 years Operating temperature C to 35 C 15 C to 35 C within specs Storage temperature
5. Indicates the USB connectors on the display Indicates the manufacturing date 35 Indicates the temperature limitations for fe the display to operate within specs Indicates the display serial no Consult the operating instructions thrown in the trash but must be recycled according to the European WEEE Waste Electrical and Electronic Equipment directive T Indicates this apparatus must not be 52 Legal disclaimer DISCLAIMER NOTICE Although every attempt has been made to achieve technical accuracy in his document we assume no responsibility for errors that may be ound Our goal is to provide you with the most accurate and usable documentation possible if you discover errors please let us know D Barco software products are the property of Barco They are distributed under copyright by Barco N V or Barco Inc for use only under the specific terms of a software license agreement between Barco N V or Barco Inc and the licensee No other use duplication or disclosure of a Barco software product in any form is authorized The specifications of Barco products are subject to change without notice TRADEMARKS All trademarks and registered trademarks are property of their respective owners COPYRIGHT NOTICE This document is copyrighted All rights are reserved Neither this document nor any part of it may be reproduced or copied in any form or by
6. Rotate the control wheel to select DPMS For E 3620 and MDNG 5121 Press the control wheel to change the DPMS setting For MDNC 3121 MDNG 2121 and MDNG 6121 Press the control wheel shortly to go into edit mode Next rotate the control wheel to change the setting At last press the control wheel again to save the changes Cleaning your display Front glass Clean the front glass using a sponge cleaning cloth or soft tissue lightly moistened with one of the following tested products e Flux e Pril e Windex Glass Plus e Ajax glass cleaner e Bohle glass cleaner e Sidolin glass cleaner e Mr Proper e 25 ethanol solution EtOH In case none of the above cleaning products is available use plain water AN Take care not to damage or scratch the front glass Be careful with rings or other jewelry and do not apply excessive pressure on the front glass uN Do not apply or spray liquid directly to the front glass as excess liquid may cause damage to internal electronics Instead apply the liquid to the cleaning cloth 41 AN Do not use following products e Alcohol solvents at higher concentration gt 5 e Strong alkalis lye strong solvents e Acid e Detergents with fluoride e Detergents with ammonia e Detergents with abrasives e Steel wool e Sponge with abrasives e Steel blades e Cloth with steel thread Cabinet 1 Clean the cabinet using a soft cotton cloth lightly moistened with a recognized cleanin
7. Electronic Information Products Also called RoHS of Chinese Mainland he table below lists the names and contents of toxic and or hazardous substances that Barco s product may contain The RoHS of Chinese ainland is included in the MCV standard of the Ministry of Information Industry of China in the section Limit Requirements of toxic substances in Electronic Information Products BAME EF KEE ee Component Name Hazardous Substances or Elements Ki E Ka KM E Pb Hg Cd Cr6 PBB PBDE En tf FPR BCA X O 0 O O 0 Printed Circuit Assemblies Hit X X 0 O O OU LCD panel OH R Bhi A O 0 O O O External cables ARBRES 0 0 OU O 0 O nternal wiring BEI OU 0 O O O OU Metal enclosure HERO OU 0 O O O 0 Plastic enclosure EGA 2 0 0 O O O O Heatsinks EES O 0 O O O O Fan 47 HER ERD at X O O O O O Power supply unit SCE O O O O O O Paper manuals SATB O O O O O O CD manual ET HEEE SIT 11363 2006 RELER BARKAT O Indicates that this toxic or hazardous substance
8. but it also needs to be activated on your workstation To do this go to Power Options Properties in the Control Panel Barco recommends setting DPMS activation after 20 minutes of non usage USE A SCREEN SAVER TO AVOID IMAGE RETENTION Prolonged operation of an LCD with the same content on the same screen area may result in a form of image retention You can avoid or significantly reduce the occurrence of this phenomenon by using a screen saver You can activate a screen saver in the Display properties window of your workstation Barco recommends setting screen saver activation after 5 minutes of non usage A good screen saver displays moving content In case you are working with the same image or an application with static image elements for several hours continuously so that the screen saver is not activated change the image content regularly to avoid image retention of the static elements UNDERSTAND PIXEL TECHNOLOGY LCD displays use technology based on pixels As a normal tolerance in the manufacturing of the LCD a limited number of these pixels may remain either dark or permanently lit without affecting the diagnostic Se E performance of the product To ensure optimal product quality Barco applies strict selection criteria for its LCD panels To learn more about LCD technology and missing pixels consult er the dedicated white papers available at www barco com medical ENHANC Every Ba
9. control wheel to activate the User Controls function This is indicated by the scroll bar that becomes longer Rotate the control wheel to switch from On to Off Click the control wheel to confirm and return to the Settings menu Exit the menus TO ENABLE USER CONTROLS 5 6 Make sure the on screen display is not on the screen Do not use the control wheel for at least 3 seconds Only for MDNC2121 MONC3121 MONG2121 and MDONG 6121 Press and hold the control wheel for at least 5 seconds Rotate the control wheel 1 step clockwise Press the control wheel 2 times Rotate the control wheel 1 step counterclockwise Steps 4 to 6 must be performed in maximum 3 seconds In MDNC2121 MDNC 3121 MDNG 2121 and MDNG 6121 displays the user controls are automatically enabled after this procedure In other Nio displays you must enable the user controls again in the Settings menu Bringing up the OSD menu When the OSD is not on the screen rotate the control wheel to display the OSD The main menu appears Barco Nio Display MAIN MENU Luminance Settings Information EXIT Figure 20 Main menu example 25 Navigating through the OSD menus 1 Rotate the control wheel to move up and down through the menus 2 To go into a submenu rotate the control wheel to highlight the submenu Next click the control wheel to go into the submenu 3 When you click on Exit the OSD exit
10. controls installation Lin ch 2 7 Any product disassembly and the operation site for the personne 2 8 Am failures resulting from an acci licensed software product files misuse power failure or fluctuation disruption o equipment 2 9 Anys 2 10 The evaluation cost in case of a returned charged to the Customer at Barco s sole discre ent n circuit ARTICLE 3 OBLIGATIONS OF THE CUSTOMER Customer hereby assumes the following obliga requirements under the warranty condition fail Barco nv MID s performance hereunder 3 1 Customer shall 3 2 Repairs to equi or its officers agents not expose Barco nv MID ment under warranty res 23 The Customer is responsible for installing intended If there is an indication that the equi MID is entitled not to perform warranty repairs by Barco nv MID in this respect may be invoic ARTICLE 4 REMEDIES UNDER WARRANTY a Hardware If du arge o comm pecific services or procedures asked employees or representa ting the Warranty Period a Product or any part thereof fails to meet any of costs at the operation site travel expenses and travel time to and from the repair works and transport charges egligence such as but not limited to removing or deleting system files amp ailure or any change damage due to fire water thunder or lightning unication lines or due to force majeure or any reason foreign to the for by Customer related t
11. is available ALC amp DICOM options Jumps to the ALC amp DICOM Options submenu which allows to edit the settings for the DICOM display function This function is available only when the DICOM DF is selected This menu is available only in MDNC 2121 MDNC 3121 MDNG 2121 and MDNG 6121 ALC amp DICOM OPTIONS SUBMENU Correction value Shows the that is take ambient light correction value n into account in the calculation of the display function measured in lux DICOM offset The DICOM DF is recalculated at the moment the DICOM Offset is changed taking the new DICOM Offset into account e When set to Dark Room the ambient light is not taken into account e When set to Preset a preset INTO d ambient light value determined by the selected reading room is taken ccount Reading room Allows to s elect from a pre defined list of reading room types You must s elect a reading room that corresponds to the type of room the display is installed in Reading room def Jumps to the reading room definition submenu which allows to edit the reading room condi tion settings Calibration info Jumps to the calculation information submenu which displays information about the values taken into account to recalculate the DICOM DF This menu is available only in MDNC 2 and MDNG 6121 121 MDNC3121 MDNG 2121 31 READING RO
12. s on state on off The LED s orange DPMS state is not influenced by this setting So when the display goes into power saving mode the LED will turn orange even if it was switched off by this setting User controls Allows to disable the control wheel on the front When switched off the user cannot display the OSD unit the user controls are enabled again For more information Locking and unlocking user controls on page 23 Language Allows to select another language for the OSD menus Auto menu exit Allows to switch the automatic menu exit on off When switched on the OSD is closed automatically when left idle for a certain time Preferred Input Select the video resolution you wish the connected graphic board s to reproduce After changing this setting you must reboot the PC This function takes effect with plug and play graphic boards only In some displays there is only 1 setting for this function 33 Only in MDNC2121 MDNC3121 MDNG 2121 and MDNG 6121 The DPMS system will power down the display when the connected computer is left idle for a certain time Barco recommends to switch DPMS on and to use a good 7 windows screen saver to prevent image burn in image retention on the LCD panel Information menu Product The display type Serial No Indicates the display serial number SW Version Displays the current internal software version Displ
13. within specs Storage temperature 20 C to 60 C Operating humidity 8 70 non condensing Storage humidity 5 95 non condensing Operating altitude 3000 m Storage altitude 7500 m In dark reading room conditions 0 lux 67 No Coop 2MP HB Product acronym MDNC2121 Screen technology TFT AM Color LCD IPS Active screen size diagonal 541 mm 21 3 Active screen size H x V 432 x 324 mm 17 0 x 12 8 Aspect ratio H V 4 3 Resolution 2MP 1600 x 1200 Pixel pitch 0 2700 mm 0 01063 Color imaging Yes Gray imaging No Color support 24 bit Viewing angle H V 176 Uniform Luminance Yes Technology ULT Per Pixel Uniformity PPU No Ambient Light No Compensation ALC Backlight Output Yes Stabilization BLOS I Guard No Maximum luminance 750 cd m DICOM calibrated 400 cd m luminance ULT off Contrast ratio typical 1050 1 Response time Tr Tf 35 ms Scanning frequency H V 15 129 kHz 24 100 Hz Housing color Gray 68 i Video input signals DVI D Single Link 1x DisplayPort 1x USB ports 1 upstream endpoint 2 downstream USB standard 2 0 Power source Input for 24 VDC power supply unit 90 264 VAC Input for display 24 VDC For use only power Sinpro HPU100 108 Power consumption 66W nomi
14. 5 C within specs Storage temperature 20 C to 60 C Operating humidity 8 80 non condensing Storage humidity 5 95 non condensing Operating altitude 3000 m Storage altitude 7500 m In dark reading room conditions 0 lux 61 62 No Coop 3MP HB Product acronym MDNCG3121 Screen technology TFT AM Color LCD IPS Active screen size diagonal 540 mm 21 3 Active screen size H x V 433 x 325 mm 17 0 x 12 8 Aspect ratio H V 4 3 Resolution 3MP 2048 x 1536 Pixel pitch 0 2115 mm Color imaging Yes Gray imaging No Color support 24 bit Viewing angle H V 176 Uniform Luminance Yes Technology ULT Per Pixel Uniformity PPU No Ambient Light No Compensation ALC Backlight Output Yes Stabilization BLOS I Guard No Maximum luminance 800 cd m DICOM calibrated 400 cd m luminance ULT off Contrast ratio typical 750 1 Response time Tr Tf 24 ms Scanning frequency H V 15 128 kHz 25 98 Hz Housing color Gray i Video input signals DVI D Dual Link USB ports 1 upstream endpoint 2 downstream USB standard 2 0 Power requirements 100 250V nominal Power consumption 72W nominal Power save mode Yes Power management DVI DMPM Dot clock 165 MHZ OSD languages English French German Spanish Italian
15. EC governing waste from electrical and electronic equipment this product must not be disposed of with other municipal waste Please dispose of your waste equipment by handing it over to a designated collection point for the recycling of waste electrical and electronic equipment To prevent possible harm to the environment or human health from uncontrolled waste disposal please separate these items from other types of waste and recycle them responsibly to promote the sustainable reuse of material resources For more information about recycling of this product please contact your local city office your municipal waste disposal service or the shop where you purchased the product MERCURY NOTICE This Barco product consists of materials that may contain mercury which must be recycled or disposed of in accordance with local state or country laws e Within this system the backlight lamps in the monitor display contain mercury T LAMP CONTAINS MERCURY DISPOSE ACCORDING TO Hg STATE LOCAL LAW 1HE AG ARMA TURKEY ROHS COMPLIANCE Republic of Turkey In conformity with the EEE Regulation asd Turkiye Cumhuriyeti EEE Y netmeli ine Uygundur 46 DES ROHS CHINESE MAINLAND ROHS PEA ETERN se HINA ERA HEAK fii RoHS gt LAR ABV T Barco Pah HAGE SAEN RA NAPA at LEE AGE RoHS faa ate Pfs PL MCV PA gt HPS ae eR Se BK h o According to the China Administration on Control of Pollution Caused by
16. G ROOM SETTING 1 5 Select the DICOM display function See To select a display function DF on page 36 Enter the ALC amp DICOM Options submenu In the ALC amp DICOM Options submenu rotate the control wheel to select Reading Room Press the control wheel shortly to go into edi mode Rotate the control wheel to select the reading room that cor the responds to the room type the display is installed in Return to menu You can select the following reading room types CR DR MAMMO Corresponds to light conditions in diagnostic reading rooms for computed radiology digital radiology or mammography This setting has the lowest maximum ambient light ie CT MR NM Corresponds to light conditions in diagnostic reading rooms for computed tomography magnetic resonance or nuclear medicine scans Office Corresponds to light conditions in office rooms Clinical Corresponds to light conditions in diagnostic reading rooms for clinical viewing Emergency Corresponds to light conditions in emergency rooms Operating Corresponds to light conditions in operating rooms This setting has the highest maximum ambient light Reading room definition This function is available only when the DICOM display function is selected TO MODIFY A READING ROOM DEFINITION 1 Select the DICOM display function See To select a display function DF on page 36 2 Enter t
17. Nio User Guide Supported displays E 3620 MONG 5121 MDNG 2121 MDNC 3121 MDNG 6121 MONC 2121 BARCO Visibly yours This page intentionally left blank Welcome Nio is Barco s flexible industry standard display solution for diagnostic imaging Presenting an exceptional combination of innovation and performance Barco s next generation Nio display system improves your diagnostic reading routine for a multitude of medical imaging applications Following symbols may be used throughout this guide Warning Risk of frame injury to human A Caution Risk of damage to the beings product Important notice gt Note Q or remark Hint tip Additional information D Read all the safety information starting on page 43 before operating your BaRco Nio Display This page intentionally left blank Table of contents What s RTE 7 Parts controls and Connectors sesseesseesseseosseesseesesssesse 8 R E ee 8 REAP VIEW E E EE T 9 Display EE 12 Unlocking the height mechantem tsetse tssteeseesteeseeees 12 Adjusting the display Dpsltion 13 Connecting the signal Cables 16 Routing TE Ca DIOS weiss stems cadre ienakmunabawaae 17 Re attaching the Cover 17 VESA MOUNE installation eee eee tecseeseecsesseesseseeesseseseeesteseesteeseees 18 Daily operation EE 20 Recommendations for daily operatton esses teeeesteeees 20 Stand by SWItCHIAG ooo tec ecseesecseestessecstesseeseeseseeee
18. O NV MID SHALL NOT UNDER ANY CIRC INDIRECT INCIDENTAL SPECIAL OR CONSEQU TANGIBLE OR INTANGIBLE PROPERTY OR EQU OF REPLACEMENT GO MANUFACTURING SALE DELIVERY RESALE INS EN MS ALL WARRANTIES EXPRESSED OR IMPLIED INCLUDING ALL IMPLIED WA UMS PMENT LOSS O ODS OR CLAIMS OF USER FO or part in question or ii replace the Product or supply part s or component s according to the eplacement part shall be at least functionally equivalent to the original nents shall become the property of Barco and shall at Barco s request be to rectify substantial malfunctions of the software to the extent he software or supplying an alternative version of the software ranties covers the cost of material and labor RRANTIES OF AR PURPOSE ute Cus reunder TO CUS consti ties he LIABLE ions shal e Warran ANCES BE IAL DAMAG di tl omer s sole and exclusive remedy and Barco s OMER OR ANY TH ES SUCH AS BUT NOT LIMITED TO F PROFITS OR REVENUES COST OF INTERRUPTIONS THE LIABILITY OF PERATION OR SUITABILITY FOR US RD PARTY FOR DIRECT DAMAGE TO OR LOSS OF CAPITAL COST OF PURCHASE BARCO NV MID FOR E OF ANY PRODUCTS OR R SERVICE ALLATION O SERVICES COVERED BY OR FURNISHED UNDER TH IS WARRANTY CONDITION WHETHER ARISING OUT OF CONTRACT NEGLIGENCE STRICT TORT WARRANTY OR OT SERVICES UPON WHICH SUCH LIABILITY IS BASED ARTICLE 7 FORCE MAJEURE Either
19. OM DEFINITION SUBMENU Reading room Indicates the reading room type you are editing You can select another room to edit by rotating the control wheel Max ambient light This indicates the maximum ambient light hat corresponds to the selected reading room If the measured ambient light is higher han the value entered here you should ake measures to darken the room or select another reading room type Preset corr value This value is taken into account in the calculation of the DICOM DF if DICOM Offset is set to Preset To each reading room type corresponds another preset value This menu is available only in MDNC2121 MONC 3121 MDNG 2121 and MDNG 6121 CALIBRATION INFORMATION SUBMENU Preset Ambient Shows the ambient light correction value value taken into account to calculate the DICOM DF expressed in lux Bright luminance Shows the bright luminance value taken into account to calculate the DICOM DF Dark luminance Shows the dark luminance value taken into account to calculate the DICOM DF Ambient correction Shows the ambient light correction value taken into account to calculate the DICOM DF expressed in cd dm This menu is available only in MDNC2121 MONC 3121 MDNG 2121 and MDNG 6121 i Settings menu DPMS Allows to switch the display power management system on off See note below Power LED Allows to switch the power LED
20. Portrait 385 x 525 585 x 250 mm Landscape 485 x 475 535 x 250 mm Dimensions w o stand W Portrait 385 x 485 x 115 mm x Hx D Landscape 485 x 385 x 115 mm Dimensions packaged Wx 500 x 675 x 320 mm H x D Net weight with stand 13 kg Net weight w o stand 9 kg Net weight packaged with 15 kg stand Net weight packaged w o 11 kg stand Height adjustment range 60 mm Tilt 5 30 Swivel 45 45 Pivot 90 Te 58 Mounting standard VESA 100 mm Screen protection Protective non reflective PMMA cover Recommended modalities CT MR US DR CR NM Film Certifications CCC GB4943 2001 GB9254 1998 Class A GB9254 2008 Class A GB17625 1 2003 DEMKO EN60601 1 1990 A1 1993 A2 1995 A11 1993 A12 1993 A13 1996 IEC 60601 1 1988 A1 1991 A2 1995 2nd edition UL 60601 1 1st edition 2006 04 26 CAN CSA C22 2 No 601 1 M90 2005 FDAS10K RoHs MDD WEEE CE 0120 VCCI FCC Class B KETI Supplied accessories User Guide Quick Installation Sheet Video cable DVI Dual Link Mains cables UK European CEBEC KEMA USA UL CSA adaptor plug NEMA 5 15P Chinese CCC External power supply Optional accessories A QA software MediCal QAWeb Unit per pallet A Pallet dimensions A Warranty 5 years Operating temperature 0 C to 40 C 15 C to 35 C within specs Storag
21. any means graphical electronic or mechanical including photocopying taping or information storage and retrieval systems without written permission of Barco 2012 Barco N V All rights reserved Technical specifications Nio 2MP Product acronym MDNG 2121 Screen technology TFT AM LCD Dual Domain IPS Active screen size diagonal 540 mm 21 3 Active screen size H x V 432 x 324 mm 17 0 x 12 8 Aspect ratio H V 4 3 Resolution 2MP 1600 x 1200 Pixel pitch 0 2700 mm Color imaging No Gray imaging Yes Number of grayscales LUT 1024 grey levels 10 12 in LUT out Viewing angle H V 170 Uniform Luminance Yes Technology ULT Per Pixel Uniformity PPU No Ambient Light No Compensation ALC Backlight Output Yes Stabilization BLOS I Guard No Maximum luminance 1650 cd m DICOM calibrated 500 cd m luminance ULT off Contrast ratio typical 850 1 Te Response time Tr Tf 23 ms Scanning frequency H V 15 129 kHz 24 100 Hz Housing color Gray Video input signals DVI D Dual Link USB ports 1 upstream endpoint 2 downstream USB standard 2 0 Power requirements 100 240V nominal Power consumption 65W nominal Power save mode Yes Power management DVI DMPM Dot clock 280 MHz OSD languages English French German Spanish Italian
22. arts that by definition are subject to wear and tear including but not limited to a CRT s LCD panels b Backlights in diagnostic LCD displays when the backlight run time2 is beyond the Guaranteed Backlight Lifetime3 of that model when used at the Factory Calibrated Luminance4 Eg1 A display is used at 8 hours day ie 2 920hours year he display system is covered with a warranty period of 5 year he Guaranteed Backlight Lifetime of that model is 17 000hours he Factory Calibrated Luminance cannot be achieved anymore after 4 year thus corresponding to 1 680hours Result the backlight replacement is performed under warranty Eg2 A display is used at 24 hours day ie 8 760hours year The display system is covered with a warranty program of 5 year The Guaranteed Backlight Lifetime of that model is 17 000hours The Factory Calibrated Luminance cannot be achieved anymore after 2 5years thus corresponding to 21 900hours Result the backlight replacement does not make part of the warranty coverage 1 Consumable is a part that can be replaced by the user 2 Backlight run time is the total time that an image including use of a screen saver has been applied to the screen this value can be consulted via the OSD buttons On Screen Display 3 Guaranteed Backlight Lifetime is the number of backlight hours during which a predefined luminance value ie the Factory Calibrated Luminance wi
23. ating instructions set forth in the operating manual of the Product in question and shall not have been otherwise misused abused damaged For the purpose hereof normally used shall mean a regular ordinary and routine usage of the Product in question as intended and or recommended by Barco vi been maintained at all times in accordance with Barco s instructions or in absence thereof at least with intervals and in a manner consistent with generally accepted practice for this type of products B The warranty described herein shall not include the following 2 1 Any hardware or software item procured from a source other than Barco nv MID or their official agent or distributor and integrated by Customer or a third party into Barco nv MID supplied equipment 2 2 Any host configuration not explicitly supported by Barco nv MID 2 3 All software installed on the system whether they are acquired from Barco nv MID or third party An exception is made for software delivered by Barco nv MID that would prove to be a cause for the mal functioning of the hardware covered under this Agreement 2 4 Normal wear and tear use under circumstances exceeding specifications such as use in dusty environment or under excessive temperature conditions abuse unauthorised repair or alternation lack of proper configuration or maintenance damaged or modified or removed serial number cosmetic refurbishment 2 5 Repair or replacement of consumables or specific p
24. ay Runtime Indicates the total time the display has been operating including the time in stand by Backlight Runtime Indicates the total time the display has been operating excluding the time in stand by In some NIO displays these functions are called Display Lifetime and Backlight Lifetime Their function however is the same as described in the table above 34 Changing Display Functions Concepts Display function selection is possible only in MDNC3121 MDNG 2121 and MDNG 6121 displays e The Display Function menu lets you select a display function DF e When you select the DICOM DF you can define the DICOM DF to be recalculated taking the ambient light into account e In this case the recalculation can be based on an illuminance of 0 lux Dark Room or a preset value Preset determined by the selected reading room e Inthe latter case you must select a reading room that corresponds to the type of room the display is installed in E g if the display is installed in a room where CT scans are observed the CT MR NM reading room is the preferred selection e The reading room is defined by 2 parameters e Maximum Ambient Light defines the maximum light allowed in this type of room This value can be adjusted within certain limits determined by the selected reading room e Preset Correction Value is the predefined correction value for this reading room This va
25. co s Product manual or in the agreement between Barco and Customer the Warranty Period shall be a Hardware 12 months commencing on the Barco date of invoice b Software 3 months commencing on the Barco date of invoice otwithstanding the provisions of clause 2 repair and replacement of defects in material and or workmanship under this warranty shall be accomplished in our works according to the terms and conditions as set forth hereafter a 1 1 Any claim under the Warranties must be notified to Barco in writing within 8 days from the date the defect or ailure has been discovered or noticed the first time The Customer upon the occurrence of any equipment failure shall contact Barco nv MID customer support centre or an authorised service centre by telephone fax or e mail and shall rovide the applicable customer support person with a complete description of the problem being encountered including he model and serial number of the equipment in which the problem has arisen 2 The customer support person shall diagnose the problem experienced by the Customer and shall advise the Customer on how to proceed Customer support may ask to return the faulty equipment or faulty subassemblies to the Barco nv or a MID customer support centre or an authorised service centre for repair activities In no event shal Customer return a defective Product or part thereof to Barco without Barco s prior written approval n the ev
26. contained in all of the homogeneous materials for this part is below the limit requirement in SJ T11363 2006 X RMA RAE URES EDEN HAM EHS EE SIT 11363 2006 ENR Ge Indicates that this toxic or hazardous substance contained in at least one of the oe materials used for this part is above the limit requirement in S T11363 2006 OD Cp pur fai EP AZAR AEA GE HA m AB EEN EPP ERE A BA EFUP br Barco P mh PRAES EFUP kr zeit Ae Fr UM SIDEN Hi TEE m ZEBRA EFES HE IO HABE PRE All Electronic Information Products EIP that are sold within Chinese Mainland must comply with the Electronic Information Products Pollution Control Labeling Standard of Chinese Mainland marked with the Environmental Friendly Use Period EFUP logo The number inside the EFUP logo that Barco uses please refer to the photo is based on the Standard of Electronic Information Products Environmental Friendly Use Period of Chinese Mainland Er 10 Nio Regulatory compliance information INDICATIONS FOR USE E 3620 MDNG 2121 MDNC 3121 MDNC 2121 The products are intended to be used in displaying and
27. e temperature 20 C to 60 C Operating humidity 8 80 non condensing Storage humidity 5 95 non condensing Operating altitude 3000 m Storage altitude 7500 m In dark reading room conditions 0 lux Nio 5MP Product acronym MDNG 5121 Screen technology TFT AM LCD Dual Domain IPS Active screen size diagonal 541 mm 21 3 Active screen size H x V 422 x 338 mm 16 5 x 13 3 Aspect ratio H V 5 4 Resolution SMP 2560 x 2048 Pixel pitch 0 165 mm Color imaging No Gray imaging Yes Number of grayscales LUT 10 bit 10 bit in LUT out Viewing angle H V 170 Uniform Luminance No Technology ULT Per Pixel Uniformity PPU No Ambient Light No Compensation ALC Backlight Output Yes Stabilization BLOS I Guard No Maximum luminance 700 cd m DICOM calibrated 500 cd m luminance ULT off Contrast ratio typical 800 1 Response time Tr Tf 50 ms Scanning frequency H V 30 124 kHz 45 85 Hz Te m Housing color Gray Video input signals DVI D Dual Link USB ports 1 upstream endpoint 2 downstream USB standard 1 1 Power requirements 100 250V nominal Power consumption 61W nominal Power save mode Yes Power management DVI DMPM Dot clock 330 MHz OSD languages English Dimensions with stand W x H x D Port
28. ent the return to Barco of the defective Product is authorized by Barco Barco shall issue to Customer an RMA Return Material Authorization e Customer shall apply for an RMA number to the closest Barco nv MID Customer support centre or an authorised service centre as listed at www barcomedical com unless otherwise indicated e one way cost of packing transport and insurance related to shipping the alleged defective Product or part to Barco for repair or replacement shall be borne by Customer The one way cost of packing transport and insurance related to ipping of the repaired or replacement Product or part to Customer shall be borne by Barco wv 3 The Customer shall return freight prepaid the defective equipment or subassemblies in its original packaging with the assigned RMA number for repair to the Barco nv MID Customer support centre or an authorised service centre A Replacement parts used shall be new or equivalent to new parts for the revision level of the equipment A replacement LCD panel will be new or similar run time The warranty period for the replacement parts will expire at the same moment as the original warranty period of the equipment All parts replaced hereunder and returned to Barco nv MID or an authorised service centre shall become the property of Barco nv MID or the authorised service centre 1 5 The repaired equipment shall be returned to the Customer by regular freight at Barco nv Ms char
29. equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged o try to correct the interference by one or more of the following measures O e Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help CANADIAN NOTICE This ISM device complies with Canadian ICES 001 Cet appareil ISM est conforme a la norme NMB 001 du Canada Explanation of symbols On the display or power supply you may find the following symbols nonrestrictive list LCE 0120 Indicates compliance to the essential requirements of the Directive 93 42 EEC Indicates compliance with Part 15 of the FCC rules Class A or Class B Indicates the display is approved according to the UL regulations K Indicates the display to the c UL regulations approved according Indicates the display is approved according to the DEMKO regulations Indicates the display is approved according to the CCC regulations Indicates the display is approved according to the VCCI regulations 50
30. estesseestestes 22 Locking and Unlocking user contre 23 Bringing UP the OSD men 25 Navigating through the OSD mens 26 Making selections in the OSD mens 26 Changing values in the OSD mens eeccccceceeseseeteeteetesteeteeteenen 27 Advanced operation sssscssscsssssesecssssersssssecseneers On screen display Of nput Selection menu Luminance and color menu 29 Display Function men 30 SCTUINGS UE UE ES MFOPMALION men 34 Changing Display FUNGUONS stees 35 Te i COMECE DIS arree n ce Assia ees nite eee es E 35 Display function selection oo eeeccceecee testes teeeestesteestesteeteeeeeseee 36 ALGE DICOM OPTIONS cc eegend need Eesen een 37 Switching DPMS opd 40 Nee 41 Eelere EE A E EE A E E E 41 Cabine ee 42 Important information sssessessesesesessessssssesresessssesesees 43 Safety Information 43 Environmental IMOPFM ATOR ders iesse eeneg 46 Regulatory compliance Information 49 Explanation Of SyMDOl Senani iiaa 50 Ee En 52 Technical Specifications ieia 53 Wola OK State UE 71 What s in the box Your Barco Nio Display comes with e this Barco Nio Display guide e a system CD e a DVI cable e a DisplayPort cable MDNC 2121 only e a USB cable e a set of AC power cords e an external power supply If you ordered a Barco display controller it s also in the box together with its accessories A dedicated user guide is available on the system CD Keep your original packaging It is des
31. g product for medical equipment The cabinet has been tested for resistance to the following products e Cidex Betadine e Alcohol Isopropyl and Ethyl e Ammonia based cleaners Windex e Aquasonic Gel In case none of the above cleaning products is available use plain water iN Do not apply or spray liquid directly to the cabinet as excess liquid may cause damage to internal electronics Instead apply the liquid to the cleaning cloth 2 Repeat with water only 3 Wipe dry with a dry cloth E Important information Safety information GENERAL RECOMMENDATIONS Read the safety and operating instructions before operating the equipment Retain safety and operating instructions for future reference Adhere to all warnings on the equipment and in the operating instructions manual Follow all instructions for operation and use ELECTRICAL SHOCK U RISK OF ELECTRIC SHOCK 4 bd DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER TO QUALIFIED SERVICE PERSONNEL TYPE OF PROTECTION ELECTRICAL Equipment with external power supply Class equipment DEGREE OF SAFETY FLAMMABLE ANESTHETIC MIXTURE Equipment not suitable for use in the presence of a flammable anesthetic mixture with air or with oxygen or nitrous oxide NON PATIENT CARE EQUIPMENT Equipment primarily for use in a health care facility that
32. ge 1 6 Barco nv MID will replace a product that fails within 90 days after shipment from Barco with a new one ensuring color matching in the event of a diagnostic multi head display configuration Barco aims to ship the new replacement product within 2 business days after receipt of the Customers notification in writing ARTICLE 2 CONDITIONS PRECEDENT FOR WARRANTY AND ITEMS EXCLUDED FROM WARRANTY A The Warranties shall apply only to the extent the Products or any parts thereof have i been transported and stored at all times in the original packaging in the conditions as specified by Barco such as covered and secure location minimum and maximum temperature maximum humidity or in absence thereof at least in conditions consistent with generally accepted practice for this type of products ii been handled at all times in accordance with Barco s instructions or in absence thereof at least with the care and caution consistent with generally accepted practice for this type of products ili been installed strictly in accordance with the instructions and directions given by Barco if and to the extent the Te S Products have not been installed by Barco or its authorized subcontractors iv not been subject to any unauthorized access alteration modification or repair or attempts thereto v been at all times normally used for the intended purpose and operated in strict accordance with the oper
33. he ALC amp DICOM Options submenu 3 Inthe ALC amp DICOM Options submenu rotate the control wheel to select Reading Room Def Press the control wheel shortly to open the submenu 4 Select the reading room definition you wish to modify Thereto rotate the control wheel to select Reading Room Press the control wheel shortly to go into edit mode Rotate the control wheel to select the reading room Press the control wheel shortly to confirm the selection 39 40 5 6 To modify the maximum ambient light for this reading room rotate the control wheel to select Max Ambient Light Press the control wheel shortly to go into edit mode Rotate the control wheel to change the value Press the control wheel shortly to save the changes You can change this value within certain limits determined by the selected reading room To modify the Preset correction value for this reading room rotat e the control wheel to select Preset Corr Value Press the control wheel shortly to go into edit mode Rotate the control wheel to change the value Press the control wheel shortly to savethe changes You can change this value within certain limits determined by the selected reading room Switching DPMS on off To switch DPMS ON OFF 1 When there is no OSD on the screen rotate the control wheel The main OSD menu appears Rotate the control wheel to select the Settings menu Press the control wheel shortly to open the menu
34. hysically installed in your computer If you are using a Barco display controller please consult the dedicated user guide available on the system CD Unlocking the height mechanism In the factory the height positioning system in the display foot is blocked with a red clip to prevent damage during transportation Before installing the display you must remove this clip Figure 5 Location of the clip TO REMOVE THE CLIP 1 Position the display with its rear side facing you 2 Pull the red clip out of the fixation holes in the foot 3 Keep the clip in case the display needs to be shipped later 12 Adjusting the display position You can change the orientation of the panel at any time but it is more convenient to select landscape or portrait orientation before connecting the cables Figure 6 Portrait orientation Fj g ure 7 Landscape orientation 13 TO CHANGE THE PANEL ORIENTATION 1 Stand at the front side of the panel and take the panel at both sides 2 Very important Til the panel before changing the orientation A Should you change the panel orientation without tilting it first you might irreversibly damage the tilt amp swivel mechanism Figure 8 Tilt the panel before rotating 14 3 To change from portrait to landscape turn the panel counterclockwise g Figure 9 4 To change from If after insta panel orientation depends on To r
35. igned for this display and is the ideal protection during transport Parts controls and connectors Front view Figure 1 Front side Power LED USB downstream port contro wheel Rear view REAR VIEW OF E 3620 MDNG 5121 Figure 2 Rear side connector compartment Tilt amp swivel foot cover cover Tilt a swivel foot Slot for security cable DVI digital video input USB upstream port USB downstream port Dc power input lilt amp swivel foot clip REAR VIEW OF MDNC 3121 MDNG 2121 AND MDNG 6121 Figure 3 Rear side Connector compartment Tilt amp swivel foot cover cover Tilt amp swivel foot DC power input 5 Vdc Slot for security cable DVI digital video input USB upstream port USB downstream port O Tilt amp swivel foot clip 10 REAR VIEW OF MDNC 2121 Figure 4 Rear side Connector compartment cover Tilt amp swivel foot cover Tilt amp swivel foot Slot for security cable DisplayPort video input DVI digital video input USB upstream port USB downstream port DC power input O Tilt amp swivel foot clip 11 Display installation D Prior to installing your Barco Nio Display and connecting all necessary cables make sure to have a suitable display controller p
36. is intended for use where contact with a patient is unlikely Te j 44 POWER CONNECTION EQUIPMENT WITH EXTERNAL 12 VDC POWER SUPPLY e Power requirements The equipment must be powered using the delivered medical approved 12 VDC power supply e The medical approved DC power supply must be powered by the AC mains voltage protective earth terminal POWER CONNECTION EQUIPMENT WITH EXTERNAL 24 VDC POWER SUPPLY e Power requirements The equipment must be powered using the delivered medical approved 24 VDC SELV power supply e The medical approved DC power supply must be powered by the AC mains voltage protective earth terminal TRANSIENT OVER VOLTAGE If the equipment is not used for a long time disconnect it from the AC inlet to avoid damage by transient over voltage To fully disengage the power to the unit please disconnect the power cord from the AC inlet POWER CORDS e Utilize a UL listed detachable power cord 3 wire type SJ or equivalent 18 AWG min rated 300 V min provided with a hospital grade type plug 5 15P configuration for 120V application or 6 15P for 240V application e Do not overload wall outlets and extension cords as this may result in fire or electric shock e Mains lead protection U S Power cord Power cords should be routed so that they are not likely to be walked upon or pinched by items placed upon or against them paying particular attention to cords at plugs and receptacle
37. lian Dimensions with stand W x H x D Portrait 385 x 525 585 x 250 mm Landscape 485 x 475 535 x 250 mm Dimensions w o stand W xH xD Portrait 385 x 485 x 115 mm Landscape 485 x 385 x 115 mm Dimensions packaged W x H x D 500 x 320 x 675 mm Net weight with stand 12 3 kg Net weight w o stand 8 3 kg Net weight packaged with 17 3 kg stand Net weight packaged w o 13 3 kg stand Height adjustment range 60 mm Tilt 5 30 Swivel 45 45 Pivot 90 66 ie Mounting standard VESA 100 mm Screen protection Protective non reflective PMMA cover Recommended modalities CT MR US DR CR NM Film Certifications BSMI CCC GB4943 2001 GB9254 1998 GB9254 2008 GB17625 1 2003 DEMKO EN60601 1 1990 A1 1993 A2 1995 A13 1996 IEC 60601 1 1988 A1 1991 A2 1995 2nd edition UL 60601 1 1st edition 2006 04 26 CAN CSA C22 2 No 601 1 M90 2005 FOA510K RoHs MDD WEEE CE 0120 VCCI FCC Class B KETI Supplied accessories User Guide Quick Installation Sheet Video cable DVI Dual Link Mains cables UK European CEBEC KEMA USA UL CSA adaptor plug NEMA 5 15P Chinese CCC USB 2 0 cable External power supply Optional accessories A QA software MediCal QAWeb Unit per pallet A Pallet dimensions A Warranty 5 years Operating temperature 0 C to 35 C 15 C to 30 C
38. ll be provided by a specific diagnostic display model This figure is printed on the Warranty certificate of each display or can be requested at your local Barco office 4 Factory Calibrated Luminance is the typical luminance value that a specific diagnostic display model is calibrated at during the production process This figure is printed on the Warranty certificate of each display or can be requested at your local Barco office c Lamps optical components in projectors d Replacement because of i image retention as a result of not correctly using screen saver and or Display Power Management System DPMS as explained in the user manual prolonged operation of the display with a static image on the same screen area ii a number of missing pixels that is lower than the total allowable number as mentioned in the product specifications ge E iii difference in color tempera product specifications ure that is lower than the total allowable difference as mentioned in the iv difference in color temperature as a result of not using all displays of a multi head configuration at the same rate v LCD luminance uniformity that is in within the product specifications or luminance uniformity performance that is inherent to LCD technology Barco nv MID does not warrant a minimu m life time nor a performance of any of the consumables 2 6 Replacement of moveable parts such as power cords remote
39. lue can be adjusted within certain limits determined by the selected reading room e The reading room parameters are pre defined in the display according to the AAPM American Association of Physicists in Medicine However they can be changed within certain limits 35 Display function selection TO SELECT A DISPLAY FUNCTION DF 1 When there is no OSD on the screen rotate the control wheel to display the OSD The main menu appears 2 Rotate the control wh Press the control whe 3 Rotate the control wh control wheel shortly 4 Rotate the control wh 5 Press the control whe eel to select the Display Function menu els ee to go into edit ee els You can select the following DFs hortly to enter the menu to select Display Function Press the mode to select the desired DF hortly to activate the new selection DICOM Select a DICOM display function for most medical viewing applications The DICOM function results in more visible grayscales in the images Dynamic Gamma 2 2 Dynamic Gamma 1 8 These are gamma functions that are shifted to take into account the non zero luminance of an LCD panel when driven wi h a black signal They are especially useful in CT applications to improve the perception of low Haunsfield values Native If you select Native the native panel behavior will not be corrected Test This is iden
40. measured luminance by the internal sensor This is a read only value It is expressed in a percentage of the alibrated value 100 is calibrated EN Luminance target Allows to manually adjust the luminance target See note below Color target Allows to select from a list of factory defined and user defined color targets You can select from a range of standard Daylight D color temperatures Clearbase Bluebase and Native The higher the D number the more bluish he color temperature is ative is the uncorrected color emperature of the LCD panel H Viewing mode Allows to select a pre defined viewing mode Diagnostic is the standard mode for iewing medical images In Text mode the calibrated luminance is decreased so the viewing conditions are optimal for viewing office documents text documents spreadsheets etc lt Only in MONC 2121 and MDNC 3121 displays displays 29 30 When you change the luminance target the display will adjust its backlight to reach the target This can be seen in the Measured luminance line When the luminance target cannot be reached e g due to aging of the backlight the Measured luminance line changes to Minimum value reached or Maximum value reached Display Function menu Display function Allows to select from a list of pre defined display functions If the DICOM DF is selected an additional function
41. n The panel standard attached to the tilt amp swivel foot is compatible with the VESA 100 mm standard So it can be used with an arm stand according to the VESA 100 mm standard Therefore the tilt amp swivel foot must be removed from the panel O e Use an arm that is approved by VESA according to the VESA 100 mm standard e Use an arm that can support a weight of at least 13 kg 28 66 lbs TO ATTACH THE DISPLAY TO AN ARM STAND 1 Put the display face down on a clean and soft surface Be careful not to damage the panel screen 2 Remove the tilt amp swivel foot cover 3 Remove the small screw A fixing the small plastic cover on top of the foot Next remove the small cover itself Figure 14 Display with tilt amp swivel foot cover removed Unscrew the 2 screws fixing the round plastic cover B Lift up the round plastic cover Remove the four screws fixing the foot while supporting the foot nN non Mi P tach the arm stand firmly to the panel using 4 screws M4 x 8 gt 4 screws M4 x 8mm Figure 15 Location of the screws 19 Daily operation Recommendations for daily operation OPTIMIZE THE LIFETIME OF YOUR DISPLAY Enabling the Display Power Management System DPMS of your display will optimize its diagnostic lifetime by automatically switching off the backlight when the display is not used for a specified period of time By default DPMS is enabled on your display
42. nal Power save mode Yes Power management DVI DMPM Dot clock 165 MHz OSD languages English French German Spanish Italian Dimensions with stand W x H x D Portrait 385 x 525 585 x 250 mm Landscape 485 x 475 535 x 250 mm Dimensions w o stand W Portrait 385 x 485 x 115 mm x Hx D Landscape 485 x 385 x 115 mm Dimensions packaged Wx 500 x 320 x 675 mm H x D Net weight with stand 13 kg Net weight w o stand 9 kg Net weight packaged with 15 kg stand Net weight packaged w o NA stand Height adjustment range 60 mm Tilt 5 30 Swivel 45 45 Pivot 90 Mounting standard VESA 100 mm Te Screen protection Protective non reflective PMMA cover Recommended modalities CT MR US DR CR NM Film Certifications UL60601 1 CB60601 1 CSA C22 2 No 601 1 EN60601 1 2 EN55011 Limit B ICES 001 B EN61000 3 2 3 EN61000 4 2 3 4 5 6 8 11 VCCI CE0120 KETI CCC BSMI Demko FCCB FDA 510K CMDCAS MDD WEEE RoHS Supplied accessories User Guide Quick Installation Sheet Video cables 1 x DVI Single Link 1x DisplayPort Mains cables UK European CEBEC KEMA USA UL CSA adaptor plug NEMA 5 15P Chinese CCC USB 2 0 cable External power supply Optional accessories A QA software MediCal QAWeb Unit per pallet A Pallet dimensions A Warranty 5 years Operating
43. o land ling heg In some cases the cases it will not be rotated e g whe after rotation display control panel and restart orientation Lin he display or t while an image is o raphic board an image will be ate the panel fron ecessd scape to portrait tu he sy portrait to stem andscape rn clockwise ry change the image resolu he systen tomaticall n pixels would you change the n the screen the result d the resolution of t rotated au he image y in other be lost ion in the n after changing the 15 Connecting the signal cables TO CONNECT THE SIGNAL CABLES TO THE DISPLAY To get access to the connectors remove the connector compartment cover by pulling down the 2 clips at the top of the cover The location of the connectors depends on the display type Figure 10 In puts E 3620 MDNG 5121 iesse B S L L L Figure 11 Inputs MDNC 3121 MONG 2121 and MDNG 6121 o o Go o omme E n Figure 1 HO T 0 000 2 Inputs MDNC 2121 e Connect one end of the DVI DisplayPort cable to the DVI DisplayPort input of the display 1 Connect the other end of the DVI DisplayPort cable to the DVI DisplayPort connector of the display controller board nnec strea nnec connec e CO po su co 16 nnec rd de wer suppl
44. o verification of repaired equipment roduct deemed functional is not covered under warranty and will be tion based on a case by case evaluation ions as partial consideration for Barco nv MID performance of its ure by Customer to meet its obligations under this paragraph shall excuse personnel to any unsafe working conditions ulting from improper maintenance or repair performed by the Customer tives shall be borne by the Customer at its additional cost and expense he Barco nv MID equipment in an environment for which it was pment was used even temporary outside its specifications Barco nv and terminate the warranty agreement Any actions that have been taken ed to the Customer at normal pricing he Warranties then upon Customer s request Barco shall at its sole option and cost promptly and within 20 working days either i repair ect the Produc terms and conditions contained in article 1 A r part The replaced Product parts and or compo returned by Customer to Barco at Barco s cost b Software Barco s sole obligation shall be technically reasonably possible by amending t c The repair or re ARTICLE 5 DISCLAIMER OF WARRANTIES BARCO NV MID DISCLA MERCHANTABILITY AND FITNESS FOR A PART or corr jacement under the Wat CU ARTICLE 6 The remed sole and e LIMITATIO ies speci xclusive N OF LIABILITY ied in these Terms and Con iability for Barco s breach o BARC
45. party shall be r the performance of t ma SG eleased from perfor is agreement is im ed Te HERWISE SHAL L NOT EXCEED THE PRICE OF THE ITEM OR ITEMS OF GOODS OR nce of its obligations under this agreement to the extent and for so long as by reason of force majeure For the purposes of this clause the 73 74 expression force majeure means but shall not be limited to industrial dispute fire mobilisation requisi ion embargo currency transfer prohibitions insurrection lack of means of transport restrictions of the use of energy and generally any circumstances which are beyond the control of the parties and hinder performance by one party of his ob ARTICLE 8 GENERAL igations 8 1 Customer acknowledges its understanding that all software and electronic devices including Barco nv MID products are subject to possible error mechanical or electrical failure and should not be relied upon in inappropria e applications or without proper backup and or other safety precautions whenever personal injury or property damage may result from failure or error of the product 8 2 Barco nv MID shall not be responsible for machine failure and or its failure to render service or main causes beyond its reasonable control enance due to B410582 08 March 2012 Barco n v President Kennedypark 35 C 3500 Kortrijk Belgium 0120 www barco com
46. rait 408 x 489 549 x 250 mm Landscape 492 x 531 591 x 250 mm Dimensions w o stand W xH xD Portrait 408 x 492 x 115 mm Landscape 492 x 408 x 115 mm Dimensions packaged W x H x D 500 x 320 x 675 mm Net weight with stand 12 5 kg Net weight w o stand 8 5 kg Net weight packaged with 15 2 kg stand Net weight packaged w o NA stand Height adjustment range 60 mm Tilt 5 30 Swivel 45 45 Pivot 90 60 ie Mounting standard VESA 100 mm Screen protection Protective non reflective PMMA cover Recommended modalities CT MR US DR CR NM Film Certifications BSMI CCC GB4943 2001 GB9254 1998 Class A GB9254 2008 Class A GB17625 1 2003 DEMKO EN60601 1 1990 A1 1993 A2 1995 IEC 60601 1 1998 A1 1991 A2 1995 2nd edition IEC 60601 1 ed 2 am amp am2 UL 60601 1 1st edition 2006 04 26 CAN CSA C22 2 No 601 1 M90 2005 FDAS10K RoHs MDD WEEE CE 0120 VCCI FCC Class B KETI Supplied accessories User Guide Quick Installation Sheet Video cable DVI Dual Link Mains cables UK European CEBEC KEMA USA UL CSA adaptor plug NEMA 5 15P Chinese CCC USB 2 0 cable External power supply Optional accessories A QA software MediCal QAWeb Unit per pallet A Pallet dimensions A Warranty 5 years Operating temperature 0 C to 40 C 15 C to 3
47. re 20 C to 60 C Operating humidity 8 70 non condensing Storage humidity 5 95 non condensing Operating altitude 3600 m Storage altitude 7500 m In dark reading room conditions 0 lux Nio 5MP Product acronym MDNG 6121 Screen technology TFT AM LCD Dual Domain IPS Active screen size diagonal 541 mm 21 3 Active screen size H x V 432 6 x 324 5 mm 17 0 x 12 8 Aspect ratio H V 4 3 Resolution SMP 2800 x 2100 Pixel pitch 0 1540 mm Color imaging No Gray imaging Yes Number of grayscales LUT 1024 grey levels 10 12 in LUT out Viewing angle H V 170 Uniform Luminance Yes Technology ULT Per Pixel Uniformity PPU No Ambient Light No Compensation ALC Backlight Output Yes Stabilization BLOS I Guard No Maximum luminance 1100 cd m DICOM calibrated 500 cd m luminance ULT off Contrast ratio typical 1000 1 Response time Tr Tf 32 ms Scanning frequency H V 15 129 kHz 24 100 Hz Te S Housing color Gray Video input signals DVI D Dual Link USB ports 1 upstream endpoint 2 downstream USB standard 2 0 Power requirements 100 240V nominal Power consumption 78W nominal Power save mode Yes Power management DVI DMPM Dot clock 280 MHZ OSD languages English French German Spanish Ita
48. s WATER AND MOISTURE Never expose the equipment to rain or moisture Never use the equipment near water e g near a bathtub washbasin swimming pool kitchen sink laundry tub or in a wet basement VENTILATION Do not cover or block the ventilation openings in the cover of the set When installing the equipment in a cupboard or another closed location heed the necessary space between the set and the sides of the cupboard INSTALLATION Place the equipment on a flat solid and stable surface that can support the weight of at least 3 equipments If you use an unstable cart or stand the equipment may fall causing serious injury to a child or adult and serious damage to the equipment THIS APPARATUS CONFORMS TO CE0120 MDD 93 42 EEC class IIb product IEC 60601 1 UL 60601 1 CAN CSA 22 2 No 601 01 M90 cUL CCC GB4943 1995 IEC 60950 1 MDNC 2121 Medical equipment with respect to electric shock fire and mechanical hazards only in accordance with UL 60601 1 and CAN CSA C22 2 NO 601 1 NATIONAL SCANDINAVIAN DEVIATIONS FOR CL 1 7 2 Finland Laite on liitett v suojamaadoituskoskettimilla varustettuun pistorasiaan Norway Apparatet m tilkoples jordet stikkontakt Sweden Apparaten skall anslutas till jordat uttag 45 Environmental information DISPOSAL INFORMATION WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT This symbol on the product indicates that under European Directive 2002 96
49. s the submenu and jumps to the previous higher level menu When you click on Exit in the main menu the OSD is hidden Barco Nio Display MAIN MENU Luminance Settings 2 Q Information ee SETTINGS EXIT DPMS On Power LED On User controls On EXIT 1 Rotate the control wheel 2 Press the control wheel Figure 21 OSD menu navigation Making selections in the OSD menus 1 Navigate through the menus and highlight the parameter you wish to select 2 Click the control wheel to make a selection or to toggle between several settings 26 Changing values in the OSD menus 1 C C avigate through the menus and highlight the parameter you wish to adjust ick the control wheel to go into edit mode Rotate the wheel to change the value ick the wheel to enter the new value and return to the menu 27 Advanced operation On screen display OSD Input Selection menu Auto Detects the incoming video signal automatically and displays it on the screen DVI Always displays the DVI signal on the sreen When no DVI signal available there will be no image on the screen DP Always displays the DisplayPort signal on the screen When no DP signal available there will be no image on the screen Only in MDNC2121 displays 28 Luminance and color menu In grayscale Nio displays this menu is called Luminance Measured Indicates the actual luminance
50. specifica E USER COMFORT rco multi head display system is color matched with the highest tion in the market Barco recommends keeping color matched displays together Furthermore it is important to use all displays of a multi head configuration at the same rate to preserve color matching hroughout the economic lifetime of the system MAXIMIZE QUALITY ASSURANCE The MediCal QAWeb system offers online service for high grade Quality Assurance providing maximum diagnostic confidence and uptime Barco recommends to install Medical QAWeb Agent and apply the default QAWeb policy at least This policy includes calibration on regular intervals Upgrading to Medical QAWeb Server offers even more possibilities Learn more and sign up for the free Medical QAWeb Essential level at www barco com medical qa 21 22 Stand by switching ON E 3620 AND MDNG 5121 DISPLAYS When the display is on and no on screen display is visible push and hold the control wheel at the front for a few seconds to switch the display in stand by The LED turns orange Push and hold Figure 16 Location of the control wheel When the display is in stand by press the control wheel to switch it back on ON MDNC 2121 MDNC 3121 MDNG 2121 AND MDNG 6121 DISPLAYS 1 When the display is on and no on screen display is visible push the control wheel at the front shortly 2 An on screen message appears asking to press to confirm
51. temperature 0 C to 40 C 15 C to 32 C within specs Storage temperature 20 C to 60 C Operating humidity 8 70 non condensing Storage humidity 5 95 non condensing Operating altitude 3600 m Storage altitude 7500 m Regulation causion ops Medical equipment with respect to electric e us SPOCK fire and mechanical hazards only in accordance with UL 60601 1 and CAN CSA 22 2 NO 601 1 70 In dark reading room conditions 0 lux Warranty statement BARCO MID GENERAL WARRANTY TERMS AND CONDITIONS Applicable from Jan 1st 2008 ARTICLE 1 PRODUCT WARRANTY Barco nv Medical Imaging Division warrants that the equipment will be free of defects in workmanship or material for he warranty period or the specific period of a warranty extension program Hardware Barco warrants that upon delivery hereunder the Products shall i conform to its specifications in effect at the date of delivery and ii be free from defects in material and workmanship the Warranties Software Barco warrants that software written by Barco shall perform substantially in accordance with the specifications in effect at the date of delivery Software is inherently susceptible to bugs and errors Barco makes no warranties with respect to the software which is provided to Customer on an as is basis and does not warrant uninterrupted or error ree operation of the Products Unless otherwise indicated in Bar
52. tical to the Native DF Gamma 2 2 Select one of these display functions in Gamma 1 8 case the display is to replace a CRT display wi ha gamma of 1 8 or 2 2 respectively 36 User This is a user definable DF Use MediCal QAWeb to define the DF ALC amp DICOM Options DICOM offset INTRODUCTION The DICOM DF will be recalculated only when another DICOM Offset is selected The DICOM DF will be recalculated based on the new offset setting To SELECT A DICOM OFFSET 1 Select the DICOM display function See To select a display function DF on page 36 2 Enter the ALC amp DICOM submenu 3 In the ALC amp DICOM Options submenu rotate the control wheel to select DICOM Offset Press the control wheel shortly to go into edit mode 4 Rotate the control wheel to select an offset 5 Press the control wheel shortly to activate the selection 37 38 YOU CAN SELECT THE FOLLOWING OFFSETS Dark room The DICOM DF will be recalculated taking an ambient light value of 0 lux into account This means that the measured ambient ight does not influence the DICOM DF Preset The DICOM DF will be recalculated taking a preset ambient light value into account This value is determined by the selected Reading Room and can be adjusted manually within certain limits Reading room selection This function is available only when the DICOM display function is selected TO SELECT A READIN
53. viewing digital images for review and analysis by trained medical practitioners These devices must not be used in primary image diagnosis in mammography Caution USA Federal law restricts this device to sale by or no the order of a physician or a practitioner trained on its use INDICATIONS FOR USE MDNG 5121 MDNG 6121 The products are intended to be used in displaying and viewing digital images including digital mammography for review and analysis by trained medical practitioners Caution USA Federal law restricts this device to sale by or no the order of a physician or a practitioner trained on its use FCC Class B This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this
54. y Connect th pply to a grounded po a PC USB downs any USB device ors 3 the DC power input 4 of the display to the external DC e other end of the external DC power wer outlet by means of the proper power ivered in the pac ream connector to the display s USB m connector by means of a USB cable 2 o one of the display s USB downstream aging Routing the cables BD nd the cables in the connector compartment together with the able tie inside the connector compartment e Put the connector compartment cover back on the display Pay ttention that the signal cables are positioned under the bulge in the cover ush the cables into the clips on the rear of the tilt amp swivel foot e Bind the cables together above and under the foot by means of the 2 velcro strips attached to the inside of the foot cover packed nside the accessory box t last put the foot cover back in place cy ef e o e gt Re attaching the covers Figure 13 Installing the cover 1 The foot cover is packaged separately in the accessory box Unpack the foot cover 2 Push the upper side of the cover onto the foot so that the hooks inside the cover are positioned right under the bulges at the rear of the foot 17 18 3 Slide the cover upward while moving the lower side of the cover towards the foot 4 Press the cover to the foot so that it makes a clicking sound VESA mount installatio

User Manual - CNET Content Solutions

Contents

Download Pdf Manuals

Related Search

Related Contents