Home

IPCAM 400W MANUAL Weatherproof WiFi Network IP Camera

1. IPCAM 400W VA MANUAL SCHWAIGER PHONE amp COMPUTER Weatherproof WiFi Network IP Camera TABLE OF CONTENTS 1 Introduction 2 Delivery contents 3 Using the IPCAM for the first time 3 1 App installation 3 2 Connecting the IPCAM to WLAN 3 3 Connecting the IPCAM via WPS 3 4 Operating previously configured IPCAMs again 3 5 Adding IPCAMs that are set up for operation to the app 4 General troubleshooting 5 Technical specifications 1 INTRODUCTION Congratulations and thank you for purchasing the Schwaiger IPCAM400W This user manual should assist you in handling and operating the network camera Please make sure that you first become familiar with the characteristics of your IPCAM and WLAN router to rule out potential sources of error 2 DELIVERY CONTENTS 1x camera IPCAM400W 1x holder 1x power supply 1x user manual 3 USING THE IPCAM FOR THE FIRST TIME 3 1 APP INSTALLATION Download and install the UCare Cam app You can find the app in Google Play or the app store for your smartphone You require at least Android 4 0 or IOS 5 0 to ensure full compa tibility between the app and your smartphone s operating system iOS Android App Store uCare Cam Download Link Google Play Store uCare Cam Download Link IPCam Passwort 0000 Benutzer Passwort admin Passwort 0000 3 2 CONNECTING THE IPCAM TO WLAN Use the delivered connection cable to operate your
2. IPCAM for the first time before subsequently establishing a connection between the network camera and the network Step 1 After the camera has been connected to the electricity wait until the red and green LEDs alternately light up If only one of the two LEDs lights up after 1 minute hold down the Reset WPS button for approximately 10 seconds The camera will then restart and try to establish a connection again Step 2 As soon as the LEDs alternately light up you can search for the network WIFI CAM p2p in the WLAN settings in your terminal device and establish a connection to it Step 3 Open the UCare Cam app and select WIFI Connect at the lower edge of the display Activate the Router Mode and press Next until you can see a picture of your IPCAM Select Next once more You will now be requested to enter the name SSID and the password of your available WLAN network In the final window you can give your IPCAM a name and a password Once the setup is complete the IPCAM will connect itself to your WLAN This can take several minutes If a connection cannot be established reset the IPCAM by holding down the Reset WPS button and make sure the SSID and password of your WLAN network have been entered correctly 3 3 CONNECTING THE IPCAM VIA WPS You can also connect the IPCAM via WPS if your WLAN router supports WPS Step 1 Use the delivered connection cable to operate your IPCAM for
3. e QR the IPCAM as well Intranet Your code on the back of as the name and WLAN will search foryour IPCam will be password of the existing IPCAMs scanned here To IPCAM scan the QR code hold the terminal device s camera over the QR code 4 GENERAL TROUBLESHOOTING Disconnect the device from the electricity for 10 seconds You can reset the settings in your IPCAM by holding down the Reset WPA button for approximately 10 seconds Make sure that the IPCAM is within the range of your WLAN router 5 TECHNICAL SPECIFICATIONS Frequency Band 2 400 2 4835GHz Compression nn MJPEG j Image Sensor nn 1 4 color CMOS csnsee Lens Lens f3 6mm Horizontal 39 3 Vertical 26 8 Resolution a MGA 640x480 QVGA 320x240 Framerate jja 1725 FPS QVGA ccccseemssssesentee Alarm Motion Detection Sound Detection Email seascapes ed ste Smartphone Notify Message o Microphone Electronic Condenser Dimensions saiisine LOGOUT saarin Weight e APPO 4429 nnn a T a eee ee Bracket Model 5208 or KW5203 optional SCHWAIGER Schwaiger GmbH www schwaiger de Wiirzburger Str 17 90579 Langenzenn Irrt mer Abweichungen und nderungen bei den technischen A Angaben und Abbildungen vorbehalten All technical data and ae S ou C 070 O illustrations are subject to errors deviations amp modifications m RoHS YA
4. the first time Wait until the red and green LEDs alternately light up ca 15 seconds If only one of the two LEDs lights up after 1 minute hold down the Reset WPS button for approximately 10 seconds The camera will then restart and try to establish a connection again Step 2 As soon as the LEDs alternately light up hold down the Reset WPS button for 2 seconds and activate the WPS function in your WLAN device With successful WLAN Router verbindung both LED s red green shine at the same time Step 3 Open the UCare Cam app and select WIFI Connect at the lower edge of the display Confirm the WPS Setup Mode and press Next The UID and IP address of your IPCAM will now be displayed select them In the final window you can give your IPCAM a name and a password Once the setup is completed the IPCAM will connect itself to your WLAN 3 4 OPERATING A PREVIOUSLY CONFIGURED IPCAM AGAIN Your IPCam will connect itself automatically to the WLAN network again when you turn it on If this does not happen connect the IPCam again by following the instructions listed in sections 3 2 or 3 3 3 5 ADDING IPCAMS THAT ARE SET UP FOR OPERATION TO THE APP Start the app and select Import Installed WIFICAM You now have 3 options Option 1 Option 2 Option 3 You can manually You can use the You can select enter the UID found menu item Scan Scan Camera QR on the back of Cameras UID in Code Th

IPCAM 400W MANUAL Weatherproof WiFi Network IP Camera

Contents

Download Pdf Manuals

Related Search

Related Contents