Home

USER`S MANUAL For Macintosh and PC

1. 010907 510914 06 raver Automated Optical Disc Duplication amp Printing System USER S MANUAL For Macintosh and PC PRIMERA 2007 All rights reserved Notices The information in this document is subject to change without notice NO WARRANTY OF ANY KIND IS MADE WITH REGARD TO THIS MATERIAL INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE No liability is assumed for errors contained herein or for incidental or consequential damages in connection with the furnishing performance or use of this material This document contains proprietary information that is protected by copyright All rights are reserved No part of this document may be photocopied reproduced or translated into another language without prior written consent Trademark Acknowledgments Windows is a registered trademark of Microsoft Corporation All other trademarks are the property of their respective owners Printing History Edition 6 0 010907 Copyright 2004 All rights reserved FCC Compliance Statement This device complies with part 15 of the FCC rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation For Users in the United States This product is intended to be supplied by a UL listed Direct Plug In Power
2. Getting Started 7 lt a o gt 8 Print time varies according to which print mode has been selected section 3 A In most cases print time takes no more than 2 minutes After printing the first disc the Publisher s Printer Disc Tray opens automatically The Robotic Disc Transporter moves the finished disc to the Output Bin 9 The Robotic Disc Transporter will now load the second recorded disc into the Printer Tray for printing 10 The process starts over and repeats until all blank discs are gone or the number you have specified via software are copied and printed 11 Now that you understand the order of operation it is time to set up your Publisher 8 Getting Started Section 2 Hardware and Software Setup Setup This section will describe the step by step process of setting up your Publisher This includes information on how to load the supplies ink and disc media necessary to start producing discs A INSTALLING THE PC SOFTWARE The Installer Disc has a QuickStart menu that will guide you through the process of setting up your duplicator Please refer to the following for more information on each step 1 Place the Optical Disc Publisher Installer CD in your CDRom Drive The Installer application should automati cally launch in a few moments If it does proceed to Step 2 If it does not automatically launch follow these steps e Double click the My Computer Icon then double click
3. you re ready to start an actual recording job In this example we ll perform a simple disc to disc copy More detailed information regarding other types of jobs data discs Audio CD etc can be found in the Primo DVD Help files under the Help Menu Get Help Disc to Disc copy can be used to copy any CD or DVD master This job type reads the master disc from a specified CD DVD drive on your system to the hard drive of your computer This assumes you have checked Make a temporary image on hard drive and copy from there The master is stored in the Primo Global Image format gi in a temporary location on Creating Discs on a PC 33 lt a n gt your computer Primo uses this temporary file to make all subsequent copies that are requested The master disc is read only once to create the initial temporary GI file Disc to Disc copy is Recommended for all CD or DVD types Audio CD Data CD Software Install Disc Video CD DVD DVD ROM etc Step 1 Select File New Job Disc to Disc Copy or Select Disc to Disc Copy from the Primo Starter Window A copy job setup panel will be created in the job setup window Step 2 Select the drive you will use for the reader right click on the desired drive listed in the drive status window and choose Select Deselect as Reader from the menu A bluish green arrow pointing to the right indicates a selected reader drive for a job zg Ge Host 1 1D 0 E Cyberdry CWO58D CD R RW aS
4. Button e While holding the Cartridge Button press the Power Button until the robotics start to move e Release both buttons e To stop the test wait until the disc has moved to the Output Bin and press the Power Button Maintenance and Troubleshooting 53 lt a n gt C PC SOFTWARE TEST This will confirm that the hardware software and your PC are all communicating properly with each other properly Follow the procedures listed on the following pages 1 Launch the software from your Windows Desktop or program menu The main Application Window will appear Select the Publisher Drive by clicking on its icon on the left hand side of the screen 2 From the main Application Window click on Robotics 3 In the drop down menu go to Options Click on Check Communications You will see a dialog box stating Communication OK System Idle If you do not see this make sure that all cables are connected securely Disc Publisher Options Services Printer Robotics Disc Publisher PRO on USBOOS Check Communications Print Rejec V Record and Print Simultaneously Minimize Printing Dialog Re Select Drives 5 Click OK to get back to the main screen 6 Click on Robotics again 54 Maintenance and Troubleshooting lt a Lig 7 Select Manual Movements Duplicator Movements Reset Robotics Multiple Station Test Move each requested disc from the Repeat this with 10 Discs input stack
5. FORMAT REQUIREMENTS Your printer driver allows you to create labels in most any graphics application The driver will center the image and automatically crop it to the shape of a CD This means you do not necessarily need a template to create a CD in your favorite graphics program Simply create a custom page size of 120mm 4 72 inches square and center your image in that area and the driver will do the rest The center sizes listed in Section E should guide you in creating your disc Because the driver crops the image to the shape of a CD you do not want to make your design round You will find it is best to over bleed your design by filling the whole 120mm area with your image This ensures the outer and inner diameters will print perfectly round on your disc Label Format Requirements e 4 72 x 4 72 120mm Square Image e No Circular Images To Print and burn simultaneously through the Discribe program the image will need to be in one of the following supported file formats JPEGs TIFFs PICTs PDFs GIFs BMP JPEG 2000 MacPaint Photoshop PNG QuickTime Images SGI TGA and more In order to help you design your label included on the installation disc are templates in eps format These templates will help you get started designing your label To use the template follow these steps 1 Open the template in Photoshop or Illustrator 2 Create a new layer for your image or graphics Make sure the template layer is on top
6. Gray Plastic Input and Output Bins e Power Cord e One Three Color CMY Ink Cartridge e One Monochrome Black Ink Cartridge e QuickStart Installer Disc for use with both CD R and DVD R models e USB 2 0 Interface Cable Beige e Warranty Card e This Operator s Manual Quick Start Guide and Other Printed Information Save the carton and packing materials They will come in handy later if you ever need to transport the Publisher and or any of its parts and accessories 2 Getting Started qa mg C IDENTIFYING THE PARTS Front Panel and Top This illustration shows the Publisher its Control Panel Buttons LED indicator lights Input and Output Bins and other components Control Panel Status Lights Front Cover Ink Cartridge Carrier Color Ink Cartridge Monochrome Black Cartridge Power Button Ink Cartridge Button a TE Vicia eT eyes an hall aaa ia P eh Output Bin Reject Area CD DVD Recorders Robotic Disc Transporter Recorder Tray Button Input Bin The Robotic Disc Transporter moves discs from the Input Bin to a CD DVD Recorder to the printer and finally to the Output Bin The CD DVD Recorder is automatically loaded and unloaded by the Publisher s Robotic Disc Transporter The Recorder Tray Button manually opens or closes the Recorder Tray In normal operation the in out movement of the Recorder Tr
7. If you have difficulties in operating your Publisher the procedures in this manual and the software User s Guide should in most cases solve the problem If you still have difficulty contact the technical support number listed on the insert included in the supply pack that came with your Publisher Maintenance and Troubleshooting 57 Section 7 Technical f Model Configurations Printing Method Printing Resolution Ink Types Media Types Maximum print width Minimum PC System Minimum MAC System Disc Capacity Recordable Formats Operating Systems Interface Power Requirement Weight 58 Technical Specifications Optical Disc Publisher Pro CD R Publisher DVD R Publisher Ink Jet 4800 x 1200 dpi 2400 x 1200 dpi 1200 x 1200 dpi 600 x 600 dpi Dual Cartridges One 3 color CMY cartridge and one Black Monochrome K Ink Jet Printable Surface CD R CD RW DVD R DVD RAM DVD R Dual Layer DVD R 4 724 120mm Intel Processor III IV 750 MHz or higher 256MB RAM minimum 512 MB recommended available PCI slot one free USB 2 0 port G4 PowerPC 700MHz or higher running Mac OS Version 10 2 or higher 256MB RAM minimum 2GB free hard disk space 6GB for DVD 50 disc input 50 disc output default 100 disc input 100 disc output Kiosk Mode CD R CD Audio CD DA CD ROM CD I Video CD MP3 to CD Audio on the fly no hard drive overhead required Window 2000 2003 XP and Vist
8. PrimoDVD to Create Your Discs cccccccceeseseteteseseseseseeenenes 28 Es Using Kiosk Mode vei set iii dia aceiincnnaddieaanasieite 32 E Copying a CD or DVD odana asne KiE EA 33 Section 4 Creating Discs on a Mac esesessesessesseseeseseesseseosessesseneseeeseseosessesresess 36 A Tutorial Copy a CD or DVD ss ssssssssssssssssissssiesriesssiesressresssresseeesseessee 36 B Using Diseibe DIe ienei i airt ENRE EANA Ea EELT 39 C Printed Label Format Requirements cccccsesesesseseeseesesesseeeesees 44 D Printing Only isiensner se harii asai eeii aaia 45 E Printer Ophons srira ann E AEN R E 45 E Configuration Utility 0 sctccicetecessestcveedectesteescveasecckecascenadenssesbecdeubdacsenses 48 Section 5 Interpreting the Publisher s Indicator Lights cssssssseees 52 Section 6 Maintenance and Troubleshooting s sesessesseseseeseeseseseoseeseeeseesees 53 A Cleaning the PUblSReEr iasanen oanrin Aas 53 B Performing a Robotic Self Test c ccscscssessesesssesseessessesesessesssssesseeeesens 53 C PC software TeStinosnnseni tosissani iaiia iraa 54 D Mac Software Testescniinsnniciepii iani ai a RRE iae 55 E Cleaning the Ink Cartridges cccceccsesesessesesseesseeesseeesesesnessssesesseeesens 56 E Clearing a Media JaMag anni 56 G Transporting the Publisher ccccssssesssseeseeseeseseesesesessessssseeseeeenens 56 H Technica k SUpport ienien ioiai roiie e iaae ian 57 Section
9. image pama y6no seul soym once rotate this cD pm Jequunu y 19 u pue pul4 so the ARROWS point paume uogesqieg JeoaA to the BACK of the printer p 4 and print again qwnu WYS eu eq snw yno sau asym Jequinu y Jajua pue pul4 UONBIGIeD Je uoZzuoH Along the Vertical axis of the printed disc find the number whose lines touch For example in the above illustration Enter the number 2 into the Vertical box of the Calibration window and 0 for the Horizontal axis Select the OK button Your images should now be centered when printed on a disc After your selections have been made close out of the printer setup window You are now ready to go to an application program and print All printer driver selections will stay the same until you change them Creating Discs on a PC 23 lt a n gt Clean Change Cartridges amp Check Ink Levels Select this button to display the current ink levels as well as options for cleaning and changing cartridges Cartridge Maintenance amp Ink Levels Black Dye it g Remaining 100 Remaining 98 Change Cartridges CleanjPurge Change Cartridge s Select the Change Cartridge s button to install a new ink cartridge or to switch back and forth between previously used cartridges After the cartridge has been replaced according to the instructions in Section 2C Step 4 Installing Ink Cartridges select either the New Cartridge Installe
10. into each recorder and then put each disc into the output stack insert the disc briefly into the printer if selected Start Test MV Recorder IV Printer Continuous Test Load at least 4 5 discs into the Input Bin Click on Start Test The robotic arm will move through its entire sequence automatically If you specified more than one disc it will continue until the number you specified is completed or it runs out of discs D MAC SOFTWARE TEST This will confirm that the hardware software and your computer are all communicating properly To perform a software test please do the following 1 2 Launch Discribe Click one of the options from the quick launch menu i e Data CD Select Test Robotics from the Utilities Menu Click the Test Robot button You can select where you want discs to go during the test and the number of times to repeat the test Click Start The Publisher will perform your test Maintenance and Troubleshooting 55 qa mge E CLEANING THE INK CARTRIDGE It may be necessary to clean the ink cartridge nozzles if you notice reduced print quality or if you suspect an cartridge noz zle has become slightly dried out or clogged If you are having print quality problems follow the steps below 1 Remove the print cartridge 2 Moisten a lint free cloth with water 3 Hold the cloth against the nozzles for three seconds This will wick some additional ink onto the damp clot
11. of the image layer 3 Place your image or design your graphics on the new layer Use the template as a guide for image and graphics placement 44 Creating Discs on a Mac lt a mg 4 Before you print or save your image in another format either hide the template layer or delete the template layer The circular shape and center cut out should not be printed Use it only as a guide to layout your image D PRINTING ONLY To print simply follow the normal procedure for printing from your graphics application Select the Disc Publisher Pro as your printer Select the number of copies The Publisher will pick and print as many copies as you select E PRINTER OPTIONS The following section will examine the printer driver settings that affect the print quality of your discs To access print settings from Discribe click the Print Settings button on the Robot Write screen M Print Image on Discs Choose image TestPrint BMP Page Setup Printer Disc_Publisher_PRO HA Presets Standard x3 Publisher Settings a Print Quality Settings m x 2 F g Outer Margin 20mm y Print Quality Disc Surface Quality pan Inner Diameter 38 6 mm iv O Normal O Low O Better O Medium Enable Kiosk Mode Best High Cartridge ga ny 2 to use etal Intensity 100 O Black and Color Color Type Photo a Config Utility Save as Defaults Restore Defaults Cre B Creating D
12. the color cartridge to produce all colors including gray scale black and white images Monochrome Black is for images that have large black areas or black text This will ensure that no color ink is being used In some cases printing JPG files using Color Black for an image that is all black will still cause some color ink to be used 20 Creating Discs on a PC lt a n gt Monochrome Black is not recommended for gray scale images such as a black and white picture The ink spits of a black car tridge are not as small as the color cartridge This allows for faster black printing but at a lower dpi Using just the black cartridges for such images may result in a grainy image Color Matching NOTE Best for Graphics mode is best used for graphical images where accurate color reproduction is not as essential Images printed in this mode will look more vibrant because more ink is being used to produce them However printing images of people may produce skin tones that have a reddish tint Best for Photos mode is best used for photographic images where accurate color reproduction is very essential Images printed in this mode will look lighter than those printed in Photo mode Skin tones especially will look more natural in this mode Exact color matching of the printed discs to the screen may never be possible since there are factors that affect this out of the drivers control The surface of the disc reacts with the ink in the cart
13. 7 Technical Specifications sseessessesssesseeseeeseeseeseerseeseeneeeseeseeseeeseesees 58 TINGAOX A E E Weieshslndasdbedst ssuvedeslesesabednontertansundesesedscnsaneieed 60 iii Interactive Feature in this PDF Document There are interactive features that will allow you to jump to different locations within the document Each listing in the Table of Contents is interactive Place the cursor on either the words or the page number A small hand with a pointing finger icon appears Click on the line with the icon and the document will jump to that page If you want to return to the Table of Contents move the icon to the top of the page and click on the arrow marked TOC Navigating through the Index is similar Place the icon on one of the listings or page numbers click on it and it will move to that page The text relating to the Index listing will appear in red Returning to the Index can be done by clicking on the arrow marked Index Section 1 Getting Started THANK YOU for purchasing the BravoPro Disc Publisher Bravo is the perfect all in one solution for producing professional looking CD R and DVD R discs A wide variety of disc formats are supported including audio CDs Video Cds data discs and more Operation is simple and completely automatic once a job has been started To begin using your Disc Publisher please read this manual carefully This Operator s Manual is a complete step by step guide to q
14. Discribe software An image is an exact snapshot of a disc that can be stored in one easily manageable file on your hard drive Creating an image is useful for discs that you will need multiple copies of over a long period of time This project saves time by not requiring you to read in the master before every copy project Create images by using the Utilities Write Physical Image command shown in the next section Note Only Discribe images will be accepted Images created through other software or the Macintosh Disc Utility will not be recognized by Discribe B 2 Utilities and other Menus Preferences utilities and support are available through the menu that appears at the top of the screen when Discribe is active Discribe OSx File Edit QUES web eeo Discribe Untitlh Extract Audio Write Physical Image Test Robotics Show Job Queue Window V5 3 18 Charis Print Discs B 3 Saving Projects It is possible to save a project so that you can easily open it again and start it Saving projects is not possible for CD DVD copy project When you save a project the data and print file locations are stored in a small file on your computer This is different than a disc image since the actual data and print file are not stored in the project file Once a project is saved you can queue it Job queuing is described in the next section To save a project simply go to the file menu at any time and choose Save Pr
15. Host 121 ID 0 F Hl dt st CD RW GCE 8526B Oe Publisher Drive Bottom G Pioneer DYD RiwW D VR 108 9 Publisher Drive Top H Pioneer DVD RW DVR 108 Drive configuration with reader set as computer CD DVD drive Drive Status Description a amp Host 1 ID 0 E Cyberdry Cw058D CD R RW mS Host 121 ID 0 F Hl dt st CD RW GCE 8526B Se Publisher Drive Bottom G Pioneer DYD RiwW D VR 108 DR Publisher Drive Top H Pioneer DYD RiwW D VR 108 Drive configuration with reader set as Publisher drive Recommended Step 3 Select the recorder s that will record this job by double clicking the drive in the drive status window A red arrow pointing to the left indicates a selected recorder drive This selection may already automatically be made for you by the software Step 4 Select the number of copies and the recording speed 34 Creating Discs on a PC lt a Step 5 Check the print box if you want to print a label on the disk Type the full path and name of your image file into the box or click on the Browse button to open a standard Windows Open dialog to locate the file If you have not yet created a label to print on the disc click on the SureThing button to open SureThing and create a label Refer to Section 3B for Instructions on how to create a label Once you close SureThing The label file will automatically be associated with your job Step 6 Check the box next to Make a temporary image on hard drive and co
16. Input Port Power Switch USB 2 0 Port The USB 2 0 Port is connected to an open USB 2 0 port on your PC with the USB 2 0 cable included with your Publisher 4 Getting Started lt a n gt The Power Input Port connects to the included power cable The internal power supply is a switching 100V 240V power supply The Power Switch shuts off all power to the Publisher D PC SYSTEM REQUIREMENTS Before getting started it is important for you to verify that your PC meets the minimum system requirements Here s what you need in order to successfully copy discs at 8x or above with the PrimoDVD 2 1 software e 700 MHz or faster Pentium III IV processor running Windows 2000 XP or Vista e 512 MB or greater RAM e Free hard drive space of at least 10 GB e Available USB 2 0 Port This looks the same as a USB 1 0 port Make sure you have a USB 2 0 port for optimal performance If your PC does not have these minimum system requirements system performance may not be acceptable E MAC SYSTEM REQUIREMENTS Before getting started it is important for you to verify that your computer meets the recommended system requirements Here s what you need in order to successfully burn and print with the Discribe software e G4 PowerPC 700MHz or higher running OS X version 10 2 or higher e 256MB RAM e Free hard drive space of at least 2 GB up to 6 GB for DVD e Available USB 2 0 Port Do not connect the Publisher to any USB hubs o
17. Supply marked Class 2 or a UL listed ITE Power Supply marked LPS with output rated 12VDC 4 5A or higher This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Re orient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help Use of shielded cables is required to comply with the Class B limits of Part 15 of the FCC Rules You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate and or obtain warranty service for this equipment For U
18. SureThing CD Labeler PRN Print files created through the Publisher Printer Driver STD files As described earlier these are files created in SureThing CD Labeler This is the recommended file type for printing as it offers the most flexibility PRN files Note These are files created from virtually any Windows graphics application Instead of printing to a printer you print to file In some programs you can print directly from that software s Print screen through the correct printer driver software for the brand and model of printer you ve installed on your Publisher to a prn file Adobe Illustrator and CorelDRAW are examples of such programs Most of the popular higher end graphics applications give you this option of printing directly to a file If your graphics software does not allow a direct print to a file you will need to go into your Windows Control Panel Printers where you will be able to select File from your list of available printer ports This will enable the driver to print to a PRN file from any application You must change the port back to the USB port before you can print D USING PRIMODVD TO CREATE YOUR DISCS Now that you have a design for your disc you are ready to publish The example given in this chapter is for a simple disc to disc copying job using PrimoDVD software Please refer to the Help File accessible from Primo s Help Menu for further information on recording discs Go to Hel
19. a Mac OSX Version 10 2 or higher USB 2 0 port 100 120VAC 220 240VAC switch selectable 50 60Hz 1 0A 27 5 Ibs 12 5kg lt a Dimensions EMC Certifications Safety Warranty 17 8 W x 11 H x 17 6 D 452 12mmW x 279 4mmH x 447 4mmD FCC Class B CE UL UL C CE One year return to depot Technical Specifications 59 lt a Activity LOP oc cccesssssesesesesssssesesesesssesesesessessesesessssenseseseeeeseeees 29 30 Alignment Calibration ccsssscesessssssescecsesseseseecessseseseeesensees 49 Application Window cccsssececscesssssececeseseeneesssesesceneees 29 30 54 CD Tray E T 7 Centering Test Print ccssssssssssessssessssssssnssssessessseeseesesseenees 50 Color Matching cccscssssssssesssesessessssseseseesssseseseseseeseeees 21 46 Connections Rear Panel scsccsscssccsscssccsscescceecsseceecesessnssceesaes 4 Controls Front Paniel sssssssccsscssccsscssccescsscceecssscescssessesssessass 3 Disc Output Location ccssssssessssssessecssseseseseessseeseseseesesees 25 Disc to Disc Running 0 0 cece tseetseesesesessessessssesseseneeees 17 28 33 Drive Status Wind OW ccscssssceceessesesceceseseseseeseseseesessesseeseees 29 Identifying the Parts scssssssecessssesescececesesessecessessseseeseseseeeees 3 Ink Levels and Cartridge Maintenance csesssssssseeeeees 24 Ink Saturation ccccccssssssceceesssesessecesessesessecesesesseseesessse
20. age on Discs TestPrint BMP Page Setup _ Print on disc before recording Record on disc before printing Print Reject On Bad Discs In Kiosk Mode Number of discs to write al Stop job if more than 4 Go write s fail For each disc O Test Write Write Speed Max Write Speed x write C Open Next Session C Verify After Writing Ignore Read Errors Mi Using BURN Proof JustLink ne B 42 Creating Discs on a Mac lt a n gt e Kiosk Mode will allow you to increase the capacity of your Bravo from 25 to 50 BravoPro from 50 to 100 discs by dispensing finished discs out the front of the unit instead of dropping them to the output bin This allows you to place blank discs in both the input and output bins doubling your capacity An optional Kiosk Kit is available from your Primera reseller that contains a custom output bin to catch the finished discs as they leave the Bravo e Set Print on disc before recording Record disc before printing Record disc before printing is recommended for most jobs to avoid printing on discs that do not burn prop erly Print Before Recording is used for jobs involving Hockey Rink or Business Card shaped CD Rs where it is important to print before recording for proper card align ment e If using Kiosk Mode choose whether or not to Print Reject on Bad Discs in Kiosk Mode When enabled this will cause a disc that has failed to verify to be printed with the word REJECT p
21. ation 9 of 17 o gt K Surfboard E Imore 13 of 30 gt Open the text panel by clicking Text y the arrow on the text button Add text by selecting one of the E EE options below To create text Add Tent Effect that follows the curve of the Insert Special Fields disc choose Add Circular Text gt Create Text Frame You may also choose from several SureThing smart designs These design templates automatically position your text and use certain text effects to give your label a professional look You can easily toggle through smart designs by using the middle toggle button on the toggle bar below the label Finally Open the picture panel KO z m m by clicking the arrow on the aaa Pictures Clipart button Add Prowse ea ere cipar gt Browse for CD DVD Symbols any logos graphics or symbols to the label These graphics will Use Picture Tool appear on top of the background image You can size them appropriately by dragging the corner of the selected graphic When you have completed design work save your label by choosing Save Project in the Actions panel Creating Discs on a PC 27 lt a mg C USING OTHER GRAPHICS PROGRAMS While SureThing will handle most labeling needs other graphics programs can be used if you prefer Because of this we offer the flexibility to create print files PRN from any application Your Publisher will support two types of print files in PrimoDVD 2 1 STD
22. ay is controlled automatically and this button is not used Getting Started 3 lt a o gt The Control Panel contains LED Status Lights and Buttons to control the Publisher The LED Status Lights indicate that Power is ON They also blink in certain patterns to indicate an error or other condition of the Publisher See Section 5 for a full explanation of the LED Status Light conditions The Power Button turns the Publisher s power ON and OFE When the front cover is opened the Ink Cartridge Button is used to position the Cartridge Carrier for easy ink cartridge replacement When the front cover is closed pressing the Ink Cartridge button will open or close the Printer Tray The Input Output Bins are situated under the top cover of the Publisher The bins will hold up to 50 discs The right side bin is the Input Bin for blank media the left side bin is the Output Bin for finished discs The Reject Area is where discs are dropped if they do not pass a software verification test The discs slide down the ramp out in front of your Publisher The Front Cover is a durable plastic cover that will protect the Publisher from dust and interference The Ink Cartridge Carrier holds both a color ink cartridge right side pen and a monochrome ink cartridge left side pen Rear Panel This illustration shows the input ports and the power switch found on the rear panel of the Publisher a AJ Power
23. d button or the Old Cartridge Installed button accordingly Clean Purge Select Clean Purge button to send a simple test pattern to the printer Be sure to have a disc in the Publisher s input bin and the front cover closed The test pattern shown below purges ink through nozzles of your ink cartridge to clear any blockages 24 Creating Discs on a PC lt a n gt Details Select the Details button for information on the drivers firmware alignment and number of discs printed with your Publisher Click Reset Factory Default to set all print centering and cartridge alignment settings back to factory defaults Details PT_DPPro_u dll PT_DPPro_d dll Device Details Firmware Version 1 04 09 16 2004 1 Engine Firmware 24 Discs Printed 9 Vertical Offset 0 Horizontal Offset 0 CMYK Horizontal CMYK Vertical Cart1 Bidi Align Cart1 Bidi Far Cart2 Bidi Align 41 Cart2 Skew 0 Reset Factory Defaults Disc Output Location This can be set either Normal Left Bin acts as output or Kiosk finished discs deposited out the Front Exit The default is Normal Left Bin Note that this will only have an effect when doing printing only this will have no affect when recording and printing through PrimoDVD In PrimoDVD click Robotics then Options and select the Kiosk Mode check box Creating Discs on a PC 25 iva nage B CREATING A PRINT LABEL USING SURETHING The SureThing Disc Labeler software included with yo
24. eating Discs on a Mac A TUTORIAL COPY A CD OR DVD 1 Double click the Discribe Icon to launch the program You will see a splash screen followed by Discribe s Quick Start Menu 2 Click the Copy a CD DVD button OO Quick Start_ 3 FA EC FE Za DISCRIBE 53 VS 3 23 CharisMac Engineering Inc 1990 2006 Welcome to the Discribe CD Mastering System Select your new disc s format below or drag items onto this window to auto select a format E a Data CD Audio CD Copy a CD DVD 3 Place your master disc in the Publisher Drive Important You must place your master disc in the drive AFTER you open the Discribe software QO ___Discribe Untitled _ gt l V5 3 23 CharisMac Engineering Inc 1990 2006 _ CD DVD Copy B _ Source Recorder 1 Pioneer DVR 111 16x8 DL DVD RW 40x24 CDR W At USB z3 Time 46 54 Total Time 46 54 p gt Show Message Log 36 Creating Discs on a Mac lt a n gt 4 Select the drive that contains your master as the source drive 5 Click the Burn button At this point if you are using a BravoPro or XRP for the first time on this computer you will be prompted You must choose a robot and a recorder to write a disc Click OK The screen below will appear The robot should automatically be selected You will need to choose the top and bottom drives After you make this selection Discribe will remember it for future jobs You wil
25. eseseessseseees 21 Input Bit cccsscscssesssessssecsecsssseececsesseseonsesestecesesesseseseaeseeseenseseensoees 4 Inner Diameter sseessseessesessescssesosseeseseesoseessesessescesesseseesesesse 22 47 Job Set Up Winndow ccccccrsscreceserescrssssecesssesssssesesessseesssseseeessenes 29 Job Status Window ssscsscssscssssesessesessesceesessesesseseeseseeseseeees 30 Kiosk Mode Setup and USe ccssssssssssesssssesseeeseeees 32 43 46 LED Status Lights sisisi saersi rns nns aisinn eka iiis 4 Output BiN ssisssiisssiisississniisssssseissscssotioassakss6sissuiissios riis suier esasi sses 4 Overview of Operation s essesssssessessesresseoresresresneoresnessessesnessesses 6 Paper Size scscssssssssceceessssescececesssseseecesesssseseesesessseeseeeeseseeseseeseenseees 19 Power INpul cscccccesssesssseecsssseseecsrssseeonsessseecesesesseseseaeseeseenseseeseenes 5 PriMODVD Software scccssssssssssscssscsssssscesccsccsscescesecees 1 28 29 Print FileSisissessscsscsssosscasesosossassde dsoscsonteisesssassedsesensssvanssehessasossebossise 28 Printer Driver Software ccsseessssssescecsesesseseesessseeseseeseseseees 28 PRN Piles scssssssssesiness sssseisccwaassssacnssncteasecassseansesedvoagacognsdesncssasesusesecsers 28 Reject Area ccccssssssssessssessssessssessssessssessssssssesesssseseeseseesaeeased 4 7 31 RESOLUG OD eaincsssssscsesoesstcssesnasntssncisosesdssossacsessionsnsonpansasessenscsssdesnsedbae
26. etails that may no longer be present on the main screen The Log may be viewed by clicking on View Show Log The log may be saved this happens automatically every time you exit the software Emptying the log will delete all entries permanently Overview of Recording Three basic recording operations are available 1 actual recording 2 test recording and 3 verifying Actual recording is self explanatory Discs will be recorded without any testing beforehand If you have used the Publisher successfully before with a particular brand of media that is highly reliable you may choose to record without testing or verifying This will deliver the highest throughput rate of finished discs Test recording performs all of the operations of recording with the drive s laser turned on to reading power A test recording run will determine if the data source will keep up with the recorder s demand Verifying will compare the data recorded to the original data This ensures that the recorded data exactly matches the original Note that is will take about twice as long to Record and Verify as compared to just Record All discs that do not verify properly will be rejected 30 Creating Discs on a PC lt a n gt Please note that if Verify is not enabled Primo will still reject discs that record improperly The Verify feature simply double checks the record job to compare that the copy and master contain the same information After your j
27. for your Publisher Hardware Installation R windows can t verify the publisher of this driver software The software you are installing for this hardware Printers Don t install this driver software You should check your manufacturer s website for updated driver software for your device has not passed Windows Logo testing to verify its compatibility with Windows XP Tell me why this testing is important Continuing your installation of this software may impair e a E or destabilize the correct operation of your system gt either immediately or in the future Microsoft strongly Install this driver software anyway recommends that you stop this installation now and Only install driver software obtained from your manufacturer s website or contact the hardware vendor for software that has disc Unsigned software from other sources may harm your computer or steal passed Windows Logo testing information Y See details Continue Anyway C STOF Installation Windows XP Message Windows Vista Message If you are using a Macintosh When connecting USB to a Mac it may be necessary to Add the printer via the Printer Setup Utility 1 Open the Printer Setup Utility located in the Applications Utilities folder O00 Printer List 4 a gt E O 5 x Y Make Default Add Delete ColorSync Show Info In Menu Name Status Hardware and Software Setup 13 lt a Ia 2 Click Add Se
28. g and Inspection ccccccccsesesseesesesssssssessesssensssseseeeeenees 2 C Identifying the Partsinieciininonennosi nasii aaeain 3 D PC System Regdiremenis seeren ae e E E NS 5 E Mac System Requirements edecanes 5 E Overview of Operation iisccc cgscusscessdecescettesscvesseatteccenteeteassverscedeaeentsts 6 Section 2 Hardware and Software Set Up ccssssssssssssseesesesesesseseeseeseeeeeees 9 A Installing the PC Software ccccccssesseessesesessesesessesessesesssnessssseeseesenenees 9 B Installing the Mac Software cssccsessessesssesesssesseesessessssseseeeeenees 9 Ci Hard wate SetuP rimini nij annenin iaiia 10 Step 1 Applying Power ccessssesecsesesesesseeseesessessseeeeseseeesesseneeeeees 10 Step 2 Loading Media ic sccticeksissstacentinsessieessasctseneteeriesstutseseeteetdneeicl 10 Step 3 Connecting the USB Cable Installing the Driver 12 Step 4 Installing Ink Cartridges c cccccessesseseseseeeseeeeseneeesesneneeeeees 14 D Tutorial Publishing Discs on a PC cecceeseessesseseeeseseseeseseeseseeseneens 15 Section 3 Creating Discs on a PC ssssessessesessesseseeseseeoseseosesseseeseseeoseseosesseseesese 18 A Setting up the Publisher s Printer Driver cccesseseseeeeeeeeenees 18 B Creating a Print Label Using SureThing ccccesssseseseeeeeseeeesens 26 C Using Other Graphics Programs cccccsessessesseeeseeseseseseseeseeeesens 28 D Using
29. h Wipe in one direction only 5 Repeat the process F CLEARING A MEDIA JAM If a disc should become jammed inside the printing area of the Publisher with the lid closed press the Cartridge Button This will eject the Printer Tray Then open the lid The Cartridge Carrier will move to the center position automatically WAIT FOR THE CARTRIDGE CARRIER TO STOP MOVING Then carefully move the cartridge carrier assembly to the left to gain access to the printer tray G TRANSPORTING THE PUBLISHER To prevent damage to the Publishers robotic arm during shipment it is important to properly secure it To prepare for transport remove the ink cartridges and disc holders close the front cover and then do the following 1 With the front cover closed switch off power to the unit 2 Press and hold the Cartridge Button 3 While continuing to hold the Cartridge Button switch on power to the unit 56 Maintenance and Troubleshooting lt a m gt Continue to hold the Cartridge Button for five seconds After several more seconds the robotics will undock and the arm will lower Power will shut off automatically once the robotics are in transport position If you have the cardboard spacer that was shipped with the unit replace the spacer inside the unit and close the cover If you don t have the cardboard spacer secure the arm and cartridges to the sides of the unit with tape and close the cover H TECHNICAL SUPPORT
30. he Help file included with the Primo DVD software e Drive Status Window Lists all of the available drives for your computer Usually your configuration has just three drives the internal drive in your PC and the Recorders installed in your Publisher e Job Set Up Window This is the space where the setup parameters for each job are displayed When you select a job by clicking the Job from the Starter Window or by clicking on the File Menu New Job a different type of Job Panel will appear in the Job Set Up Window depending upon the type of job selected Each Job Panel contains all of Creating Discs on a PC 29 lt a n gt the necessary information to run that job including source file name number of copies to make etc In addition the Job Panels report status information during the running of the job e Job Status Window As each Job Panel is formed an entry is made in the Job Status Window at the lower left side of the main Application Window When jobs are started this list displays the status of each job including the number of discs copied and the number remaining This window may be hidden by clicking on the Show Job List Panel under the View menu One other sub window available is called the Activity Log Panel It records all user actions and system responses during the recording process by time of occurrence If a problem occurs while you re not present in front of the computer you can browse the log to find out d
31. he following dialog box Now set your centering alignment values Each value is in approximately 0 1mm If you printed a centering test print this value can be determined by selecting the best value from the CD that was printed Note The number is not an absolute offset but rather is added to the current offset value stored in the printer a gt Horizontal Value 0 Vertical Value 0 Cancel Set Values Look at the finished alignment disc and pick the numbers that come closest to lining up with one another For instance on the disc shown in this manual the vertical alignment is 2 and the horizontal alignment is 0 Enter this in the alignment dialog box If you choose not to print the test print you will simply see the alignment dialog box and can enter values to move the image The unit of measure is roughly 0 1mm Making the Horizontal Calibration number smaller or more negative will move the image slightly to the left Making the Horizontal Calibration a larger value or more positive will move the image to the right If the Vertical Calibration number is made smaller or more negative the image will move slightly up If the Vertical Calibration is set to a larger value or more positive value the image will move down on the disc Creating Discs on a Mac 51 Section 5 Interpreting the Publisher s Indicator Lights The Power and Busy LED indicator lights located on the top of the Publisher can tel
32. ile formats The Help file included with the SureThing software will pro vide complete instructions on all the features in this package Go to the Help Menu Contents The following is a tutorial on creating a basic disc design C1 Click File New New Project 1 Choose a media type 2 Choose a manufacturer 3 Choose a label type 4 Template Preview 80mm Mini Disc Business Card Disc Hockey Rink Disc C2 Select 120mm Disc and click OK C3 Using the buttons on the left navigation window you may add your own background choose a pre made back ground choose from several text effects or insert a picture Click the down arrow on the button to view all options Backgrounds fim Pictures Clipart Text a Select Background Browse for Pictures Clipart Create Text Frame Create a Collage Browse for CD DVD Symbols Add Circular Text Touchup amp Effects Add Text Effect Size amp Position Use Picture Tool Insert Special Fields Properties Clear Background 16 Hardware and Software Setup lt a n gt C4 C5 C6 You may also use the smart design toggle bar below the disc template to scroll through pre made design templates lt Corporate 005 6 of 70 eS gt E lt Z Formation 9 of 17 we K Surtboard Elmore 13 of 30 Once you are happy with your design save it as a SureThing Design STD file format Close SureThing The label will au
33. isc is not recordable the Robotic Disc Transporter picks it out of the CD Tray and sends it to the Reject Area 5 The Recorders are now writing to the discs If you were to fully record a CD with data audio video or music 650 MB recording time is about 3 minutes each A full DVD records in about 7 15 minutes depending on the speed of the media to which you are recording Most jobs don t fill the entire disc so recording time is usually less than this After recording the bottom Recorder Tray opens automati cally The Robotic Disc Transporter will lift the disc out of the Recorder Tray The Recorder Tray will close and the Printer Tray will open The Robotic Disc Transporter will lower the disc into the Printer Tray and the Printer Tray will then automatically close The Robotic Disc Transporter will now pick the second disc from the top Recorder Tray and temporarily place in the Output Bin 6 If publishing more than two discs the Robotic Disc Transporter will load the Recording Drives with blank discs from the Input Bin to start recording the next round It will then move the second recorded disc from the Output Bin to the Input Bin so that the printed disc can be placed in the Output Bin when finished 7 Once recording has started on the next round printing will start with the recorded disc from the previous round This simultaneous printing and recording greatly increases the throughput of your Publisher
34. iscs on a Mac 45 lt a n gt The following is a description of the printer driver settings Cartridge to use The Black and Color setting will use both cartridges when printing your image Color will only use the Color Cartridge and Black Only will only use the monochrome cartridge for printing e Kiosk Mode Kiosk Mode will allow you to increase the capacity of your Publisher from 50 to 100 discs by dispensing finished discs out the front of the unit instead of dropping them to the output bin This allows you to place blank discs in both the input and output bins doubling your capacity Attach the Kiosk Kit to the Publisher using the Kiosk Kit installation instructions that came with your publisher This setting will be overridden by the Kiosk Mode setting in Discribe s Robot Write or Job Details Pane e Print Quality There are three options for image quality Keep in mind that Normal provides the fastest print at lower quality while Best delivers the best quality at a slower print speed e Disc Surface Quality This setting also affects the Quality of the printed image by altering the color matching profile Start with the default setting for fastest printing and the least ink consumption If the quality needs improvement move to the next highest setting e Color Matching Graphic mode is best used for graphical images where accurate color reproduction is not as essential Images printed in this mode will look more vibrant because mo
35. ished discs will be deposited out through the front reject area of the Publisher In Kiosk mode all discs would be ejected in this manner Rejects can be identified in the stack because they will not be printed in the same manner as successfully recorded discs Refer to the Kiosk Kit installation instructions below Attach the Output Bin Holder as shown aligning the Locating Tabs on the Output Bin Holder with the Slots located on the underside of the Publisher allowing the holder to hang off the edge of the table Notice the slots do allow for adjusting the position of the output bin If your discs are not falling into the bin you will be able to move the bin slightly to align it Place the Output Bin on the Output Bin Holder as shown Locating Tabs 32 Creating Discs on a PC lt a n gt Kiosk mode is enabled as follows 1 In PrimoDVD 2 1 click Robotics then Options from the main menu Disc Publisher Options Services Printer Robotics Cancel Disc Publisher PRO on USBOOS Check Communications D Print Reject V Record and Print Simultaneously Minimize Printing Dialog Re Select Drives 2 In the Options dialog box check the option labeled Enable Kiosk Mode 3 If you would like the Publisher to physically print the word Reject on rejected discs select the Print Reject option Otherwise rejected discs will simply be ejected with no printing at all F COPYING A CD OR DVD Now
36. k cartridges for Color Black printing It is important to perform this calibration every time you change a cartridge If you forget to perform this calibration you will be prompted to do so before your first print from the new cartridge Center The Print Image NOTE Your printer comes from the factory pre calibrated to print the image in the center of the CD You can use this adjustment if you need to fine tune this location If you ever wish to verify your factory calibrated Vertical and Horizontal calibration settings you can run a simple calibration procedure to assure that your images will be centered when printed on a CD To do this refer to the following steps 1 Verify that a disc and a color ink cartridge are installed in the Publisher It is important to use the same disc you normally use for your publishing because different brands of discs may vary slightly in size Also verify that the Publisher is powered ON and that it is connected to your computer 22 Creating Discs on a PC lt a o gt Click on the Center the Print Image and then the Properties button The printer will begin printing the calibration test print When the print is complete rotate disc 180 and put the disc back in the input bin and repeat step 2 using the same disc When the second run of the print is complete you should have a test print that looks similar to the following NOTE sequinu SWS eu aq ysnw After printing this
37. l not have to select them again If you make a mistake or would like to check your selection choose Test Robotics from the Utilities menu Click Open for each of the drives 1 and 2 to determine which drive is on the top and which is on the bottom Set the location appropriately Click OK Click Burn again to proceed to the next step ean Robotics Please select the Robot you want to use Robot Disc Publisher Pro At USB Ke Firmware Version 1 12 11 23 2004 Drive Type DVD R Please select the recorders in the Robot Use the open tray button while watching the recorder to make sure that you have selected the right recorder below Top 1 Plextor PlexWriter RW 52x24x52 At USB i Open Close Bottom 2 Plextor PlexWriter RW 52x24x52 At USB E3 Open Close Gor 6 The Robot Write Options window will appear This window contains selections to help you control the printing of the image number of discs recording options and more 7 Click the Print Image on Discs button to enable printing This will enable other buttons in this pane 8 Press the Choose Image button to select an image to print This will allow you to select any file type Apple s Preview supports including JPEG TIFE PICT PDE GIE BMP and more Refer to Section 4 C for label format requirements Labels can be created in any graphics program Creating Discs on a Mac 37 lt nee 9 YOU MUST CLICK Page Setup and set Forma
38. l you a lot about what is happening inside the Publisher To accurately interpret what it means when these lights are on off or flashing please refer to the following Ink Cartridge LED Power LED Publisher ff Is ready to receive job on solid both lights are slowly blinking alternately with one another both lights are rapidly blinking alternately with one another for 30 seconds on solid flashing rapidly repeating pattern of both lights flashing in unison then one light momentarily on solid Has received a job and is waiting for the Robotic Disc Transporter to load a disc Waiting for a cartridge to be installed and the lid to be closed See Section 2 A The Publisher is initializing You will see this pattern when the Publisher is first turned on Wait until the lights stop blinking before opening software or starting jobs The printer tray or ink cartridge carrier has stalled Press the Ink button to retry the operation The Publisher has a cartridge problem Check to make certain that the cartridges are installed correctly This indicates low ink warning If the left light stays solid after the flash the Color cartridge is low If the right light stays on after the flash the BlackMonochrome cartridge should be replaced 52 Interpreting the Publisher s Indicator Lights Section 6 Maintenance and The Publisher is designed to operate for extended periods of time with very
39. lease consult the software users manual that is stored on your computer in the Applications Disc Publisher folder ead Discribe Untitled b gt amp Macintosh HFS ISO 9660 2 ISO 9660 XA iof d 4 Audio CD eering Inc 1990 2006 E V Build A Mac HFS s5 Mac ISO Hybrid By Disc Copy Image CD DVD Copy 4 CD Extra 9 VideoCD FR DVD Video Audio W Universal Disk Format UDF Stream p gt Show Message Log Once you choose a new project type you will be prompted to save the original project Click No Add data to any project by dragging the data files to this win dow or by clicking the Data button browse to specific data files or folders Other popular project types are listed below with a short description of each Build a Mac HFS Use this project type to create a CD for a Macintosh only ISO 9660 Use this project type to create a data CD for a Mac and a PC Using this project type will limit file name lengths to 16 characters Creating Discs on a Mac 39 lt a n gt Universal Disk Format UDF Use this project type to create a data DVD for a Mac and a PC DVD Video Audio This project type can be used to create DVD videos from properly formatted Video_TS and Audio_TS folders on your hard drive Note Video_TS and Audio_TS folders must first be created by a DVD authoring program Disc Copy Image Use this project to create discs from previ ously created images made from the
40. lect the Disc Publisher Pro from the list of available printers Click Add again reoeo Printer Browser S ce Default Browser IP Printer Search Printer Name 4 Connection Disc_Publisher_PRO USB Name Disc_Publisher_PRO Location Print Using Disc Publisher PRO wy More Printers Add Step 4 Installing Ink Cartridges e With the cover open press the Ink Cartridge Button to move the Ink Cartridge Carrier to the load position and open the ink cartridge covers e Remove each ink cartridge from its packaging e Slowly remove the tape covering the cartridge s print head DO NOT TOUCH THE COPPER AREA e Insert the ink cartridges into the carrier copper end first and snap the cartridge cover in place Insert the color in the right holder monochrome black in the left cartridge holder The cartridge labels are color coded to the cartridge covers a Sra e Close the Publisher s front cover 14 Hardware and Software Setup lt a D TUTORIAL PUBLISHING DISCS ON A PC This section explains how to create a basic data disc with your Publisher More detailed information on the applications that are used to operate your Publisher is available in Section 3 Information on publishing discs on a Mac can be found in Section 4 A Launch PrimoDVD 2 1 Primo DVD 2 1 can be launched from your Start menu The following screen will appear the first time you launch the progra
41. little attention In fact no regular maintenance is recommended other than cleaning the outside case NOTE Do NOT attempt to oil or grease the Publisher s Robotic Arm shaft or other components You will likely cause more harm than good Any moving parts are designed to operate for the life of the machine with no additional lubrication required A CLEANING THE PUBLISHER Use a clean lint free rag with a small amount of ammonia window cleaner to clean the Publisher s outside case and trays This type of cleaner is very effective on inks that may accumulate on the printer tray Stronger cleaning solutions are NOT recommended because they may damage the paint and plastic materials from which the parts are manufactured Always disconnect your Publisher s power cords before cleaning Resume operation only after the surfaces are completely dry B PERFORMING A ROBOTIC SELF TEST To ensure that everything is working properly a Self Test feature is built in to your Publisher In this mode the Robotic Disc Transporter will go through the motions of picking and placing a disc to ensure proper working order This test may be performed without connecting the Publisher to the PC Perform the test by doing the following steps e Load some discs into the Input Bin e Open the top recorder tray by pressing the eject button on the recorder e Make sure the Publisher s front cover is closed e With the Publisher turned on press the Cartridge
42. m PrimoDVD 2 1 Ce Disc Publisher PRO Cancel Choose the drive s in your Disc Publisher If you are unsure try each Open Close button to determine the proper drive TOP BOTTOK Open Close C C Recorder at Host 1 1D 0 Cyberdry CWO58D CD R RW 12HD Open Close C G Recorder at Host 121 ID 2 Pioneer DVD RW DYR 108 1 1 Open Close O e Recorder at Host 1211D 3 Pioneer DYD AW DYR 108 1 1 Clicking the Open Close button will help you identify the drive installed in your Publisher Select the appropriate drives from the list and click OK B Once PrimoDVD is opened choose the job type from the Primo Starter screen fim PrimoDVD Starter Please choose the type of job you would like to perform or cick Get Help to see examples of each job type You can also tight click on each job icon to see more options for that job Disc Image Job GetHelp Audio Job Open Saved Job I Do not show again TECHNOLOGY INC For information on each job type and its specific use click Get Help Hardware and Software Setup 15 lt a nege C Once you choose a job type on the right side of the screen you will see a SureThing button Click on it SureThing This will launch the SureThing software a The SureThing Disc Labeler software included with your Publisher is a great tool for creating professional looking discs You can use SureThing s Smart Designs to quickly label a disc or easily import your own design in many popular f
43. ng It is important to perform this calibration every time you change a cartridge If you forget to perform this calibration you will be prompted to do so before your first print from the new cartridge Creating Discs on a Mac 49 lt a o gt Image Centering The Image Centering button will print a test pattern on your disc to help you center the printed image on your disc If you see a half moon sliver of whited un printed space on the outside or inside of your disc you may need to run this calibration Before you run the centering test print make sure the Publisher has discs and ink cartridges installed and it is connected and ready to receive a print job The Publisher will pick a disc and print a scale of numbers on it You will be prompted to open the Publisher s front cover rotate the printed disc 180 degrees reload it into the input and close the cover Click OK when ready and the Publisher O will pick the disc and print another scale of numbers The disc should look like this l Q qwnu 3WyS ey eq snw After printing this image y _ 1 y6no saui asoym once rotate this CD z 2 s qwunu y sequa pue pul so the ARROWS point eo 3 uopeqeg eonsen to the BACK of the printer p 4 and print again qwnu JWyS y q snw yno seul soym Jequinu y Jejue pue pul uonesgi e9 Je UOZHOH 50 Creating Discs on a Mac lt a n gt Once the print has finished you will see t
44. ng the Clean Cartridge button will cause the Publisher to pick a disc and place in into the printer tray The Publisher will then print a simple pattern that will flush ink through the nozzles The test pattern will also show you if any nozzles are clogged In the pattern you will see some diagonal lines which should be continuous breaks in those lines indicate a clogged nozzle Please note that it may require more than one cleaning to fully clear all nozzles If the nozzles are not fully clear after a few cleaning prints it may be necessary to remove the cartridge and actually clean the print head by gently blotting the nozzles with a moist cloth or paper towel and replace it in the Publisher Change Cartridge If you need to change cartridges it is a good idea to use the Change Cartridge button in the Configuration Utility This ensures the most accurate tracking of ink levels To change a cartridge click the Change Cartridge button The cartridge holder will move to the center of the Publisher to make it easier to install the cartridges Lift the top cover and install the cartridges and described in section 2 of this manual Once installed click the OK button and the system will update your cartridge levels Alignment Calibration Print The Cartridge Alignment prints a test print and then automatically scans the print to configure your printer for bidirectional printing and to align the color and black cartridges for Color Black printi
45. ob s have been set up each one may be started by clicking on the red Record button at the top of the Job Setup Panel Here s what the Job Setup Panel looks like Record Pause Stop 0 BEA s Ale 1 Recorders Copies 10 Speed Max Record x V Print C Documents and Settings All Users My Documents Std files T es Volume label lt DATE_TIME gt He Multisession Load last track While jobs are running they may be paused or stopped by clicking on the appropriate buttons on the Job Setup Panel The Pause Button will allow the current recording to finish then suspends operations on that job Recording is resumed by clicking the Pause Button again The Stop Button will abort any recording in progress and cause the Publisher to transport the disc to the Reject Area It will also terminate that job Record Stop and Pause actions for the currently selected high lighted job may also be selected from the Toolbar at the top of the main Application Screen Once a job is started by pressing the Record button other subsequent jobs can be created in the same manner and queued by pressing the Record Button These jobs will appear in a queue in the Job Status Window Primo can queue up to 32 unique jobs Creating Discs on a PC 31 lt a n gt E USING KIOSK MODE Kiosk Mode allows you to use both of Publisher s Bins as input doubling your disc capacity from 50 discs to 100 discs In this mode the fin
46. oject As 40 Creating Discs on a Mac lt a ne gt B 4 Queue Projects To queue a project choose the Queue Job button at the bottom of the Data Picker window instead of the Burn button If you have not yet saved your project you will be prompted to do so at this time The Robot Write Window described in section 4B 5 will be displayed Once you choose your print file and burn settings click OK The Job Queue list window will be displayed Here you can manage and edit the jobs that are in queue To start the jobs click Start Jobs e000 Job Queue Job Status 1 Build A Mac HFS Print After Wedding jpg Num Copies 3 2 Audio CD Print After jpeg jpg Num Copies 1 3 DVD Video Audio Print After StallTest BMP Num Copies 4 Job Queue O Test Write v Using BURN Proof JustLink Write Stop queue if more than 4 write s fail Ww O Kiosk Mode Creating Discs on a Mac 41 lt a mg B 5 Robot Write Window For any project Use the Robot Write Window to choose the print file change print quality settings and choose the number of copies in a project Print settings are explained in more detail in section 4D Other settings on this screen can usually be left at their default values These options are explained below Important Note For any project you must always click Page Setup Now set Format for to Disc Publisher PRO and Paper Size to CD DVD 4 Robot Write g v Kiosk Mode v Print Im
47. p Get Help 28 Creating Discs on a PC lt a o gt Operating Screens To keep things simple there is really only one main operating screen you ll need to know about in order to run the PrimoDVD Software It is called the Application Window and it looks like this oDVD or Disc Publisher Job 1 Data Job ed DER A File Edit Drive Robotics View Tools Window Help 8 x amp amp amp Gi r3 HE DN VASBDSS a td e S EE y aame g Diive SS en p 7 a Host1ID 0E o o Bi TAE 38 E Publisher Drive G 1 Recorderfs Drive Status s Copies 1 Speed Maxx Record x z Window I Pint Z Sssurething Volume labet lt DATE_TIME gt Multisession Load last track z Folder or File as on Disc Source Folders Files Size on Disc Job Set up Drag and drop Files and Folders into this list Window gt Job Status Hiob 1 Data Job Status Window 1 1 1 1 lt gt ToT T Job s opened PxHelper Auto Insert Notification OFF Autorun shield ON Under this window there are several adjustable size windows that indicate what you ve set up and what s happening the Drive Status Window the Job Status Window and the Job Setup Window A sub Window called the Activity Log is also available but it is hidden upon initial boot up of the software Below is a short explanation of each Window For more information please see t
48. py from there This is recommended for all hardware configurations Failure to check this box may cause a high number of rejected discs Step 7 Click on the red Record button Step 1 fm PrimoDVD 2 1 for Disc Publisher PRO Job 1 Direct Copy Job Untitled Edit Drive Robotics Yiew Tools Window Help A A amp G4 y g OAIIGI ca Gs L j Step 7 Drive Ba 2 Host1 1D 0 E 29 Publisher Drive B Ee Publisher Drive T 2 Recorders Steps 2 amp 3 Coses 10 Sheed Mex i a I Print fc Documents and Settings All Users My Documents Std files Test SureThing Step 4 Reader Host 1 ID 0 E Cyberdry CW058D CD R RW Status Data 0 CD D9 1 Track s Step 5 hob 1 Direct 5 60MB 018404 Used 666 88MB 341441 Free IV Make a temporary image on the Hard Disk and copy from there Step 6 Reading speed Max v Note The disc s you are about to copy may contain materials protected by Trademarks and or Copyrights Please be sure you have the right to duplicate this material 1 Job s opened PxHelper Auto Insert Notification OFF Autorun shield ON Note It is possible to use the drive in the duplicator for the Recorder drive and the reader source drive This is recommended to reduce recording variables which are introduced by using different drive models for reading and recording Creating Discs on a PC 35 Section 4 Cr
49. r the USB port on your keyboard It should be connected directly to an onboard USB 2 0 port If your computer does not have at least these minimum system requirements system performance may not be acceptable Getting Started 5 lt a n gt F OVERVIEW OF OPERATION Your new Publisher is an automated precision device intended for continuous duty publishing of discs The following is a description of the complete process of duplicating and printing a CD DVD job on your Publisher 1 Up to 50 blank discs may be loaded at one time into the Input Bin dar 2 The Publisher s integrated Robotic Disc Transporter will first check your recorder drives for a disc by attempting to pick from the recorder Then the Robotic Disc Transporter will pick a disc from the Input Bin 3 The Recorder Trays open automatically and the Robotic Disc Transporter places a disc into the each of the recorders After each disc is placed in the recorder the Robotic Disc Transporter checks the input stack to see if two discs were picked E o lo 6 Getting Started lt a n gt 4 The Recorder Trays then automatically shut If a disc does not record properly meaning that all or part of that d
50. re ink is being used to produce them However printing images of people may produce skin tones that have a red dish tint Photo mode is best used for photographic images where accurate color reproduction is very essential Images print ed in this mode will look lighter than those printed in Photo mode Skin tones especially will look more natural in this mode NOTE Exact color matching of the printed discs to the screen may never be possible since there are factors that affect this out of the drivers control The surface of the disc reacts with the ink in the cartridge to produce the color For this reason when printing the same image to different brands of discs with different printable surfaces the printed output can look entirely different 46 Creating Discs on a Mac lt a n gt e Intensity The Intensity setting will control the amount of ink saturation on the disc When printing onto the Primera ToughCoat discs 96 is usually sufficient When printing on to other brands of media or if you would like to print darker colors you may wish to increase the Intensity setting Inner Diameter The inner diameter refers to the size of the non printed center on your disc The size of the center hub can vary from one type of media to the next This allows you to set the inner diameter in millimeters allowing you to print all the way to the center hub regardless of the type of disc you are using For the discs that Primera sells u
51. ridge to produce the color For this reason when printing the same image to different types of labels with different surfaces the printed output can look entirely different Ink Saturation This option controls the ink saturation of the printed image When printing onto the printer manufacturer s TuffCoat CD media this option can be left at its default setting of 100 When printing onto other brands of printable CD media you may need to adjust this control in order to optimize the ink saturation for the printable surface of your specific CD media Click on the up and down arrows to change the ink saturation setting Lower numbers reduce the overall ink saturation while higher numbers increase it If discs do not seem to be drying completely it may be necessary to reduce this value Creating Discs on a PC 21 lt a n gt Calibration Options Click on the plus to reveal the following four Calibration options Inner Diameter This value changes the size of the non printed center Larger numbers cause the non printed center to be larger and smaller numbers make the non printed center smaller This number is incremented by 0 1mm so a change of 10 for inner diameter changes the diameter by Imm Set the diameter to 230 for Primera TuffCoat media Cartridge Alignment The Cartridge Alignment prints a test print and then automati cally scans the print to configure your printer for bidirectional printing and to align the color and blac
52. rior to being ejected from the publisher to make it easier for bad discs to be identified in the output stack when using the Kiosk Mode If this option is not enabled bad discs will be ejected with no printing at all e Stop Job after Number of Writes Fail allows you to decide how many consecutive failures the Publisher will accept prior to canceling a job e Test write sets the burn laser to read intensity and simu lates a burn but leaves the discs blank e Write speed controls the speed of the write Lower the speed if you are having recording problems e Check Open Next Session if you are burning data to a disc and you would like to append more data to the disc at a later time e Check Verify After Writing if you would like Discribe to compare each burned disc against the source for accuracy This is useful for installation discs where it is extremely important that every bit of data be accurate This is not as necessary for video or audio discs where a missing bit of data may never be noticeable by human eyes or ears Checking this option will double the total record time of the project Creating Discs on a Mac 43 lt a n gt e Check Ignore Read Errors if you know your master may have scratches but you would like to copy it anyway Be aware that copies may not be playable or may have notice able quality problems e Always check BURN Proof JustLink This prevents bad discs resulting from inadequate hardware C PRINTED LABEL
53. s 20 Specifications na eE R Ea E EE A 58 STD File csc scsssietsccesssscaeccscivissiasscstissisancaascevsescasscscassssnbceis covey siassestonss 28 System Requirements ccscsccscesesesesceeseesseseeceesesseseseseesseseeeees 5 Technical Support sssssessssseseseecesseseseseeesseseeseseesssseseseseeseseees 57 Transporting the Publisher essesssseessesresseseesressesseseesreseesseseesee 56 Troubleshooting scscsescecesessssessecesessssesseseseseesesseseseseeseseeseseseees 53 60 Index Printed in the United States of America P N 510914
54. s which is explained later in this section Creating Discs on a PC 19 lt a m gt Resolution Select the appropriate print quality option for your image Keep in mind that Normal provides the lowest quality but with the least ink usage Best provides the highest quality but with higher ink usage Print speeds also vary slightly between settings However speed is affected most by the Disc Surface Quality setting You may wish to experiment with these options to see which one is best for your particular CD media and print quality requirements Print Quality This setting affects the quality speed and ink usage of the print Color matching is also tied to this setting Start with the default setting for fastest printing and the least amount of ink consumption If the quality needs improvement move to the next highest setting Disc Surface Quality This setting affects the quality speed and ink usage of the print Color matching is also tied to this setting Start with the default setting for fastest printing and the least amount of ink consumption If the quality needs improvement move to the next highest setting Ink Cartridge Color Black is best for images that have large areas of black graphics or text Although you can print these same images with just the color cartridge often the blacks will look darker with this setting Color Only is default setting and is best for most images With this setting the printer only uses
55. se the following guide for Inner Diameter 23 mm for Primera s Tuff Coat media 24 9 mm for the Hockey Rink Disc Business Card Disc and 80mm CD e Outer Margin The Outer Margin refers to where the printing will cut off around the outer edge of your disc The size of the printable surface can vary from one type of media to the next This allows you to set the outer margin in millimeters allowing you to print all the way to the edge regardless of the type of disc you are using The outer margin for Primera s Tuff Coat Media should be set to 0 7mm e Config Utility This button launches the Configuration Utility This Utility is also available in the Print Center Printer Setup Utility by selecting the Disc Publisher Pro and clicking the Configure or Utility Icon This utility is used to report ink levels clean and change ink cartridges and align your color and black cartridges for optimal print quality In addition this utility will allow you to center and adjust your printed image Refer to section 4 F of this manual for a detailed description of this program e Save As Default The Save As Default button will save the current settings as the system wide defaults e Restore Defaults The Restore Defaults button will restore the driver settings to the factory defaults Creating Discs on a Mac 47 lt a n gt F CONFIGURATION UTILITY The Configuration Utility is a program that installs with your Publisher software This utili
56. sers in Canada This digital apparatus does not exceed the Class B limits for radio noise for digital apparatus set out on the Radio Interference Regulations of the Canadian Department of Communications Le present appareil numerique n emet pas de bruits radioelectriques depassant les limites applicables aux appareils numeriques de la class B prescrites dans le Reglement sur le brouillage radioelectrique edicte par le ministere des Communications du Canada CAUTION TO PREVENT FIRE OR SHOCK HAZARD DO NOT EXPOSE THE UNIT TO RAIN OR MOISTURE TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE EXTERIOR PANELS NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL OPERATE THE UNIT WITH ONLY THE PROPER ELECTRICAL SPECIFICATIONS AS LABELED ON THE PRINTER AND AC ADAPTER CAUTION THIS PRODUCT CONTAINS A LASER DIODE OF A HIGHER CLASS THAN 1 TO ENSURE CONTINUED SAFETY DO NOT REMOVE ANY COVERS OR ATTEMPT TO GAIN ACCESS TO THE INSIDE OF THIS PRODUCT REFER ALL SERVICING TO QUALIFIED PERSONNEL THE FOLLOWING LABEL APPEARS INSIDE YOUR UNIT CLASS 1 LASER PRODUCT LASER KLASSE 1 CAUTION USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION ii Section 1 Getting Started csecscsssssesseseceseceesssssessesecssecssessessetseseesseeseeeees 1 A Choosing a Good Location ccccccsesseesseseseessesseesseesssnesseseeseeeeeness 1 B Unpackin
57. settings of the Publisher printer driver will fit most printing needs Please refer to the following steps to change or verify your printer driver options 1 Click the Start button For Windows 2000 point to Settings and click on Printers For XP Professional click on Printers and Faxes For XP Home click on Control Panel then click on Printers and Other Hardware then click on Printers and Faxes For Windows Vista click the Windows button and choose Printers Click on the Disc Publisher Pro icon with the right mouse button and select Printing Preferences amp Printers and Faxes i File Edit View Favorites Tools Help i Q Ba T Search Folders Address Printers and Faxes Printer Tasks Add a printer 45 See what s printing Select printing preferences ey Pause printing Pause Printing amp Share this printer Sharing mj Rename this printer Use Printer Offline X Delete this printer Create Shortcut E Set printer properties Delete Rename Set as Default Printer Printing Preferences Other Places Properties 18 Creating Discs on a PC lt a m gt NOTE Most applications allow you to change these same printer driver options from their Print and or Printer Setup screens This means that you don t have to go back to the main printer setup window each time you want to change a setting or option in the printer driver These applications will usually give yo
58. t For to Disc Publisher PRO M Print Image on Discs TestPrint BMP Page Setup Page Setup Settings Page Attributes H Format for Disc_Publisher_PRO HA Disc_Publisher_PRO vY CD DVD Business Card Disc 80mm CD Hockey Rink Disc Digital Vinyl Disc Paper Size Orientation Scale Cr EB Also set the option to select a paper size to correspond with the type of disc you are using 10 Print Settings will launch the Printer Driver settings when clicked These settings are described in detail in Section 4 D of this manual 11 Select the Number of discs requested for this job 12 Once you have selected your image and chosen your pre ferred settings in the Robot Write Pane click Start to begin recording your job Note The remaining options on the Robot Write screen can almost always be left at their default values An explanation of each can be found in section 4B 5 38 Creating Discs on a Mac lt a n gt B USING DISCRIBE 5 3 B 1 Starting a Project The initial Discribe starter window provides 3 project types Audio CD Data CD and Copy CD DVD Choose one Many more projects are available once the data picker window is open Once you are in one of the main three project types you may choose any of the other available project types by clicking the drop down box at the top of the screen and selecting one of the projects For more information on any project type p
59. the icon of the appropriate CD drive containing the Software Installer disc e Double click INSTALL exe 2 In the Installer Application click the QuickStart Install button The on screen instructions will guide you step by step through the installation process B INSTALLING THE MAC SOFTWARE Before installing Discribe please note that all software must be installed on a hard disk Once you have installed the software store the original program CD ROM in a safe place Please note that your user account must have administrative rights to properly install a new printer You can check with your system administrator or check with Apple support to confirm whether or not your account has administrative rights Install the software as follows a Insert the Bravo Installation CD ROM in your system s CD ROM drive b Double click the CD ROM icon Hardware and Software Setup 9 lt a n gt c Double click on the Disc Publisher Pro Installer mpkg file icon Follow the on screen instructions d The volume containing the operating system should be selected for installation Click the Continue button All components will be installed to their proper locations e Once the installation has completed click Quit You have successfully installed all the necessary software Section C below will describe how to connect the Publisher to your Mac C HARDWARE SETUP Step 1 Applying Power e Locate the power cord supplied with yo
60. tomatically be associated with your current job in PrimoDVD Now that you have designed the label to be printed on your disc it is time to select the information you wish to write to your disc Depending on which job type you have selected you can add Data Audio Global Images or setup up a disc to disc copy Refer to the PrimoDVD help file for more specific instructions Click on the Help Menu Get Help Select the number of copies Click the Record button to start your job The Publisher will now record and print your discs Sx Bi F E 1 Recorder s Copies 10 Speed Mar gt Record zi B IV Print C Documents and Settings All Users My Documents Std files Tes v SureThing Volume label lt DATE_TIME gt a Multisession Load last track Zi Hardware and Software Setup 17 Section 3 Creating Discs on a PC There are two main components to creating discs printing and burning SureThing CD Labeler is used to design the printing on your discs PrimoDVD 2 1 controls the recording and allows you to select the image to be printed to your discs Both applications will be described in detail in this section A SETTING UP THE PUBLISHER S PRINTER DRIVER Once the Publisher software has been successfully installed you will want to take a moment to familiarize yourself with the printer driver settings for your Publisher These settings affect the print quality of your discs The default
61. ty allows you to monitor ink lev els maintain and calibrate ink cartridges and align printing on the disc The Configuration Utility can be launched from the Print Center in OSX by doing the following 1 Click the Finder Click the Applications Icon Open the Utilities folder Locate the Printer Setup Utility Printer Center in OS 10 2 Highlight the Disc Publisher Pro and click the Utility Configure in OS X v 10 2 Icon You can also launch the Configuration Utility from the Disc Publisher Pro printer settings in any printing application by clicking File then Print and selecting Publisher Settings In Publisher Settings you will find a button to launch the Configuration Utility When launched the following window appears Le e N 0600 Disc Publisher PRO Configuration Clean Cartridge Change Cartridge Align Cartridges Image Centering Black Cartridge Color Cartridge 92 86 You will see both the Color and Monochrome Ink Levels are displayed The Color Ink Level represents the lowest color in your cartridge For instance if your cartridge has 80 cyan 50 yellow and 65 magenta ink remaining the level reported would be 50 You will also see the following buttons 48 Creating Discs on a Mac lt a m gt Clean Cartridge Cartridges that sit idle in the Publisher for a period of time may start to experience some drying of ink in the tiny nozzles that make up the print head Clicki
62. u the same choices and options but in a slightly altered format Some applications do not save your printer driver option changes but instead only use your changes for the current image or print job amp Disc Publisher PRO Printing Preferences PR pions Disc Publisher PRO Settings a Disc 120mm Custom Page Size N Orientation Portrait Non printable Outer Margin 1mm units 15 Print Quality Best Disc Surface Quality High Ink Cartridge Color Color Matching Best for Photos Ink Saturation 100 B Calibration Options Inner Diameter 1mm units 386 Cartridge Alignment Center the Print Image Clean Change Cartridges amp Check Ink Disc Output Location Normal Left Bin Enable Bi di Printing Yes Paper Size The paper size option will be set to CD for printing onto printable surface CDs and DVDs The remaining options apply if you have purchased the business card adapter kit Non printable Outer Margin Adjust this value to print all the way to the outer edge of a CD This is useful if you are printing full coverage images The lower you set this value the farther to the outer edge of the CD you will print Please note that with most media the printable surface does not extend all the way to the edge of the disc Because of this you will not normally set this value to zero You may also want to adjust the inner diameter setting found under the Calibration Option
63. uickly and easily create discs with your new Optical Disc Publisher A separate Help file is provided with your Publisher that explains the operation of the PrimoDVD Software This is accessible under Primo s Help Menu Get Help and on the Mac in the Disc Publisher folder in the applications directory NOTE ON TERMS AND CONVENTIONS From this point forward the following terms and conventions will apply The BravoPro Disc Publisher Pro will be abbreviated simply as the Publisher Optical discs which can include many different types of discs including CD Rs CD RWs DVD Rs and more are all referred to as CDs or discs Please note that in order to copy and record DVDs you will need to have purchased the DVD version of the Publisher A CHOOSING A GOOD LOCATION e Place the Publisher in a location with adequate air circulation to prevent internal heat build up You will need at least 24 61 cm of overhead space to allow the top cover to open freely e Do not place the Publisher near heat sources such as radiators or air ducts or in a place subject to direct sunlight excessive dust mechanical vibration or shock Getting Started 1 lt lt a mge B UNPACKING AND INSPECTION While unpacking your Publisher inspect the carton to ensure that no damage has occurred during shipping Make sure that all supplied accessories are included with your unit The following items should be included e Optical Disc Publisher e
64. ur Publisher is a great tool for creating professional looking discs You can use SureThing s Smart Designs to quickly label a disc or easily import your own design in many popular file formats The Help section included with the software will provide complete instructions on all the features in this package Go to the Help Menu Choose Contents The following is a tutorial on creating a basic disc design 1 Open the SureThing program Choose the 120mm DiscTemplate from the window that appears 2 Open the background panel by D Daai a click the arrow on the back ground button Add your own background to the label by choosing Select Backgound Select Background Create a Collage Touchup amp Effects Size amp Position Pri i 3A Browse to the location of your Ria background image To avoid skewed or blurry printing make sure your image is 120mm square and of sufficient resolution We recommend 300 dpi Clear Background 26 Creating Discs on a PC lt a n gt 3B 4A 4B Instead of your own background you can also choose from several included Surething backgrounds To choose one of these images click the SureThing Background button in the Browse window that appears when you click Select Background Also you can easily toggle through the back grounds by using the toggle bar below the label Backgrounds are controlled by the far left toggle button 4 Corporate 005 6 of 70 eS gt E lt Z Form
65. ur Publisher e Plug the adapter into a surge protected outlet and plug the power plug into the power port on the rear panel of the Publisher Step 2 Loading Media Discs NOTE Your Publisher can print directly onto virtually any brand of inkjet printable surface CD DVD media However different brands of discs have different printable coatings Because of this you may need to adjust the printer driver settings to accommodate your specific brand of CD DVD media Refer to Section 3A and 4E for further printer driver information Due to the wide variety of printable surface CD DVD media you may find that certain brands of discs provide higher print quality than others For maximum print quality use CD DVD media authorized by Primera Refer to the following steps when loading discs in to the Publisher 10 Hardware and Software Setup lt a n gt e Open the front cover of the Publisher e The Publisher will automatically position the cartridge carrier and Robotic Disc Transporter to the center position allowing for easy access to the bins e Load the Input Bin the bin located on the right hand side of the Publisher with 50 blank discs and place the bins on the mounting pegs Hardware and Software Setup 11 lt a Step 3 Connecting the USB 2 0 Cable Connect the Publisher to your PC or Mac with your beige USB 2 0 Cable If you are using a PC If
66. you are using a PC after a few moments Windows will tell you it has found new hardware and is looking for software to install it Found New Hardware Wizard rondhe hrame ay Welcome to the Found New Windows needs to install driver software for your Primera Hardware Wizard Technology Inc Disc_Publisher_PRO This wizard helps you install software for Primera Technology Inc Dise_Publsher_PRO 7 Locate and install driver software recommended dows will guide you through the process of installing driver software r device If your hardware came with an installation CD Q or floppy disk insert it now gt Ask me again later What do you want the wizard to do Windows will ask again the next time you plug in your device or log on O install the software automatically Recommended O Install from a list or specific location Advanced Don t show this message again for this device Your device will not function until you install driver software Click Next to continue Windows XP Windows Vista If you are using Windows XP select Install the software automatically and click Next or if you are using Windows Vista click Locate and install driver software 12 Hardware and Software Setup lt a You will see a notice like the one shown below depending on which operating system you are using Click Install Anyway or Install this driver software anyway to continue installing the printer driver

USER`S MANUAL For Macintosh and PC

Contents

Download Pdf Manuals

Related Search

Related Contents