Hero‑550 User Manual - Idea-Fly
Contents
1. WWW IDEA FLY COM Hero 550 User Manual IDF 1 01 2014 10 28 version Thanks for purchasing Hero 550 Please regularly visit Hero 550 web page at www ide fly com which is updated regularly product information technical updates and manual corrections will be available on this web page Due to unforeseen changes or product upgrades the information contained in the manual is subject to change without notice Read this disclaimer carefully before using this product By using this product you here by agree to this disclaimer and signify that you have ready them fully please strictly follow the manual to assemble and use the product The manufacturer and seller assume WWW IDEA FLY COM no liability for any resulting damage or injury arising from the operation or use of this product Profile Hero 550 is a new professional multi rotor designed for aerial photograph It has the features of strong stability heavy lift long endurance frame foldable can fly in rain and dust Flight Cautions 1 Keep flying the multi rotor a distance from people building high voltage lines tall trees water etc 2 Do not get close to or touch the working motors and propellers which will cause serious injury 3 Do not over load the multi rotor 4 Make sure the propellers and the motors are installed correctly and firmly before flying 5 Make sure all parts of product are in good condition before each flight Do not fly with wore or br2. amp right tilt Push the stick left and the aircraft will tilt and fly left Push the stick right and the aircraft will tilt and fly right The aircraft will keep level and straight if the stick is centered Pushing or pulling the stick further away from center will result in a larger tilt angle and faster flight velocity SWB is for compass calibration and mode switch Toggle the E switch from position 1 to position 3 and back to position 1 at least 3 times which will force the aircraft to entre into compass calibration mode Position 1 manual mode Position2 GPS mode Position 3 RTH SWA is for control the landing gear Position 1 lowering Position 2 retracting VRA VRB dials control the pitch roll of the gimbal SWC is for the yaw of the gimbal Fall iDEAELY WWW IDEA FLY COM Intelligent Battery The intelligent battery is specially designed for the Hero 550 With battery capacity 1OOOOMAH Voltage 14 8V 3 1 Installing The lipo Battery Install the lipo battery into the quadcopter making sure to push the lipo battery as far forward as possible into the body LED Condition Indicator NoGPS Stra WanvaiNede oe ee 00 00 00 No GPSSnal GPSMode oeeo oeeo 6 or More GPS Satellites Manual Mode o o o e Menara oo oe oo oo Low LiPo Battery Voltage Caution ee oo oo oo GPS Set Altitude Head Lock Calibrating the compass 5 1 Place the quadcopter right side up on a flat level surface then pl
3. ear From Left Ground Brown Power Red Signal Yellow C 12V 3A power module port For gimbal or wireless video transmission module From Left 12V Ground D Wifi module or OSD From left Tx Ground Rx WWW IDEA FLY COM E 50HZ 1mS 2ms PWM Signal From left match with VRA VRB SWC dials for controlling the pitch roll yaw of the gimbal F for right landing gear From left Ground Brown Power Red Signal Yellow Remote controller Antenna Kt Handle F F XB Switch B SwB Switch C SwC FHC Switch D SwD F D FFA Switch A SwA 28 HOOK ARN Left trims Right stick AU AAA Left stick Right trims HMw GRUN Up Key FOZIL Down Key LCDS LCD display WEG GR Binding Key OK key SGA Cancel key TUNU Power switch BEF X 2 1 Power on the Remote control 1 Remove the battery holder then install8 new AA batteries into the battery holder double checking to make sure that the polarity is correct Reinstall the battery holder and the battery cover WWW IDEA FLY COM 2 Set SWA and SWB switches to the upper position Pull throttle control stick all the way back Turn the transmitter l owering retracting pf SWA switch lowing and retracting SWB switch manualmode GPS Mode RTH 2 2 Main Screen Use down key to receive current data 2 3 Remote control operation Remote Operati
4. er time 25mins features high strength Light weight cool look portable dustproof rain proof Frame foldable
5. ing the quadcopter is ready for flight Takeoff Landing procedures 1 Before you flight make sure LED indicator blink green 3 times Keep SWB switch at GPS hover position 2 During the flight Never pull the throttle stick to the lowest position 6 1 start the motor take off CIDEAFLY WWW IDEA FLY COM 1 Pull the left control stick and the right control stick to the lower left and lower right corners as shown in the photo then release the control sticks The motors are now armed 2 Within 5 seconds push the throttle control stick forward to turn the motors ON If you don t push the throttle control stick forward within 5 seconds or if you re flying and pull the throttle control stick all the way back to turn the motors OFF after landing you will need to re arm the motors again 6 2 land Pull the throttle stick down the aircraft will desend then land Pull the throttle stick to the bottom switch SWB to manual mode motors will stop 1 distance over home point gt 20M Height lt 20M Elevate to 20M Then fly back to home point Height gt 20M fly back to home directly 2 distance over home point lt 20M fly back to home iwenFly WWW IDEA FLY COM Specifications Diagonal Wheelbase 550mm Material Strong plastic ESC 40 A High Speed Mute ESC Motor 4008 600KV Propellers 1455 carbon propellers KIT weight 2500g with 10000mAh 4S battery Max payload 3 1KG Hov
6. oken parts WWW IDEA FLY COM Contents Center Frame 1set 1 4PCS 2 S 2red 2white Land Gear Support Tube Base Pipe Distribution board Carbon propellers WWW IDEA FLY COM M3 6 8PCS M3 5 12PCS M3 8 8PCS USB 1PCS Pad for propellers 4PCS 5 Screws kits Hex nuts 4PCS Signal wire 1PCS Top thread 8PCS p era A Ga y transmitter e 10000mah 4Sbattery Out of the box iDEAFLY WWW IDEA FLY COM Assembly 1 1 Mount Landing Gear 1 Connect Land Gear Support Tube and Base Pipe with connecting rod Fix screws 2 connect Land Gear Support Tube and Distribution board Fix screws 1 2 Assembly propellers 1 Make sure the propellers are without crack the motors are mounted firmly and rotate freely 2 Distinguish the marks on the arms and propellers make sure to match the WWW IDEA FLY COM propellers with the corresponding motors 1 3 Assembly Arms 1 red arms are aircraft nose Black arms are aircraft tail 2 Please align male Banana Plug with male plug first We recommend you hold diagonal position to make sure the aircraft does not move Then press down the arms to centre frame 3 Fix screws until touch the accessories 1 4 WWW IDEA FLY COM Connecting with other products from left match with VRA VRB VRC dials USB Port Pomel Fe Gann Be right landing gear left landing gear 12V Grou gt A A USB port B for left landing g
7. on details mode2 Aircraft Control IEn 3 a GY eo s a m na pe a aa GR Bs r WWW IDEA FLY COM The throttle stick controls aircraft altitude elevation Push the stick up and the aircraft will rise Pull the stick down and the aircraft will decend The aircraft will automatically hover and hold its altitude if the stickers are centered Push the throttle stick above the centered mid point position to make the aircraft take off When flying we suggest that you push the throttle stick slowly to prevent the aircraft from sudden and unexpected elevation The yaw stick controls the aircraft rudder Push the stick left and the aircraft will rotate counter clock wise If the stick is centered the aircraft will remain facing the same direction The yaw stick controls the rotating angular velocity of the aircraft Pushing the stick further away from center results in a faster aircraft rotation velocity The pitch stick controls the aircraft s front amp back tilt Push the stick up and the aircraft will tilt and fly forward Pull the stick down and the aircraft will tilt and fly backward The aircraft will keep level and straight if the stick is centered Pushing or pulling the stick further away from center will result in a larger tilt angle and faster flight velocity oft GPS mode RTH A A i m Jaz mr mamal mode WWW IDEA FLY COM The roll stick controls the aircraft s left
8. ual Mode position to the Return to Home position and back to the manual mode position three times quickly in a row The LED Condition Indicator on the bottom of the quadcopter will turn solid green Grasp the vertical rudder on the back of the quadcopter and lift the tail of the quadcopter up so that the quadcopter is in a vertical postion with the bottom of the quadcopter facing toward you Next carefully rotate the quadcopter clockwise along its vertical axis for three complete 360 rotations while watching the LED condition Indicator throughout the entire process Make sure to keep the quadcopter vertical throughout the entire process If the quadcopter does not stay level while you re rotating it The LEDcondition Indicator will go out If this occurs stop and jiggle the quadcopter in the vertical position until the LED turns solid Green Again Then continue rotating it until you finish three WWW IDEA FLY COM complete 360 rotations 3 Saving calibration settings Keep the quadcopter vertical Cycle the Flight Mode switch SWB from the manual Mode position to the Return to Home position and back to the manual mode position three times quickly in a row Then keep the quadcopter level Wait for the calibration settings to be saved The LED Condition Indicator will continue to illuminate solid Green When the calibration settings are saved the LED indictor will go out Then flash Red and Green NO GPS orflash green GPS lock indicat
9. ug the lipo WWW IDEA FLY COM battery 2 Do not move the quadcopter for 10 seconds after plugging the lipo battery in to allow the flight controller to initialize 5 2 When calibrating the compass do not do so in an area that may cause magnetic interference such as a parking garage near an area with steel reinforcement near metal fencing rtc 2 Remove keys cell phones and any other metal objects from your pockets that could interfere with the calibration process SWB ye A p Ai 1 Horizontal Calibration Z Keep the quadcopter level Cycle the Flight Mode switch SWB from the manual Mode position to the Return to Home position and back to the manual mode position three times quickly in a row The LED Condition Indicator on the bottom of the quadcopter will turn solid Green Carefully rotate the quadcopter clockwise along its horizontal axis for three complete 360 rotations while watching the LED Condition indicator throughout the entire process Lift the quadcopter only enough to rotate it and make sure to keep the quadcopter level throughout the entire process If the quadcopter does not stay level while you re rotating it The LED condition WWW IDEA FLY COM Indicator will go out If this occurs stop and level the quadcopter until the LED turns solid Green Again Then continue rotating it until you finish three complete 360 rotations 2 Vertical Calibration Cycle the Flight Mode switch SWB from the man
Download Pdf Manuals
Related Search