user manual - Warehouse Sound Systems
Contents
1. Www fightenofion een ay geg 5mm 192 UV LEDs Sait 1W 48 UV LEDs 5mm 192 White LEDs User s instruction manual 2317 www lightemotion com au CONTENTS SECTION INTRODUCTION UNPACKING FEATURES INSTALLATION MAINTENANCE amp PERIODIC CHECKS CONNECTIONS AND CONTROLS POWER FUSE DIP SWITCHES STAND ALONE MASTER SLAVE MODE DMX MODE DMX LEADS DMX TERMINATORS DMX CHANNEL INFORMATION FAQ SPECIFICATIONS age ONNOOARARAROD YD Please note that as part of our ongoing commitment to continuous improvement and product development the specifications in this manual are subject to change without notice Whilst every care has been taken in the preparation of this manual we reserve the right to change specifications in the course of product improvement INTRODUCTION Congratulations on the purchase of your LED product by Lightemotion We are confident that you will be satisfied with your purchase We have prepared this manual to assist you with the care and operation of this item The lighting effect can be operated in following modes Audio activated S trobing mode Automatic mode Stand alone Master Slave DMX UNPACKING CAUTION Do not use sharp objects whilst unpacking this product Contents of the carton pc lighting effect 1pc Yoke Hanging adaptor 2pcs Thumbwheels 2pcs Rubber washers 1pc IEC power lead Please note Some of the items above may be f2. turn off the Blackout on your controller CONNECTION To connect the lighting effect in DMX mode you need to use a 3 pin DMX lead Refer to Fig 7 from the DMX output socket of the controller to the DMX input socket of the first unit then from the DMX output socket of the first unit to the DMX input socket of second unit and so on and so forth Refer to Fig 10 SETTINGS You then need to set each unit s DIP switches to the addresses required REFER to DIP switches section 6 8 DMX LEAD The DMX lead is used to link up multiple units For Wiring connections refer to DMX OUT DMX 512 PIN FUNCTION 1 GND 2 DATA 3 DMX TERMINATOR A DMX terminator helps to reduce noise on the DMX chain and makes the light respond to control more accurately It should be plugged in to the last fixture in any chain For Terminator connections refer to fig 8 DMX TERMINATOR CONNECTION Connect a 120 OHM resistor across pins 2 and 3 in an XLR plug and insert into the DMX OUT socket on the last unit in the chain DMX CHANNEL INFORMATION The lighting effects use 3 DMX channels as per table 11 Table 11 DMX CHANNEL INFORMATION Intensity 7 R FREQUENT ANSWERED QUESTIONS Symptom Unit does not power up Check that the power outlet is turned on and fuse is intact Unit powers up but no light Check that the mode is set correctly and appears that you are controlling the unit correctly Unit chases const
3. antly and not to Check that the microphone sensitivity is the beat of the music not turned up too high and that the mode is set correctly Units do not work or is Check that the mode is set correctly uncontrollable when linked or in check that all the leads are OK check that DMX mode the controller is set to pin 3 positive If linking the lead should come out of the Master Slave output socket If using DMX the lead should come out of the DMX output socket SPECIFICATIONS Voltage Power Consumption Operating Frequency Power lead Fuse Sound activated Yes with sound sensitivity control Stand alone mode DMX 3 channels Ch1 Dimmer sound active and auto modes Ch2 Flash speed and auto speed Ch3 Dimmer Linkable Effects Control Colour UVLED1 48 1W LEDs DMX Male 3 pin XLR Output connection DMX Female 3 pin XLR Rated lamp life 50 000 Hrs UVLED1 28 degrees Hanging Bracket Colour Weight UVLED and LEDStrobe 2 2Kg Dimensions UVLED and LEDStrobe 356 x 248 x 165mm UVLED1 368x241x84mm gechnology e E A D C947 i emot ton www lightemotion com au 8 8
4. ersons Warranty may be void if damage has been caused by improper maintenance e Perspex lenses should be wiped with a clean moist cloth to remove dust and residue CONNECTIONS AND CONTROLS 124 365 Power input Fuse Holder Sound sensitivity pot Dip switches DMX input socket DMX output socket POWER CAUTION This lighting effect is designed to operate at 240V oS Sel S Power Consumption UVLED 55W Power Consumption UVLED1 12W Power Consumption LEDSTROBE 12W FUSE CAUTION Only use the correct fuse as specified on the rear panel of the lighting effect Disconnect the lighting effect from the mains before attempting to replace the fuse NOTE This lighting effect has a position for a spare fuse located in the fuse holder toward the outside of the fixture To replace the fuse please follow the following steps 1 Remove the fuse holder with a screw driver Refer to fig 4 2 Remove existing fuse 3 Fit new fuse 4 Refit the fuse holder Fuse M205 2A fast 4 8 DIP SWITCHES The DIP switches allow the user to change the mode and operation of the lighting effect by setting the switches to different combinations DMX To determine the starting address for the each lighting effect you should refer to your DMX controller user manual CALCULATING THE STARTING ADDRESS To calculate the starting address you add the value of all the switches which are ON and that value is the address that is requ
5. ired Refer to Fig 6 N Cc O D Q O STAND ALONE NOTE There are multiple stand alone settings available Refer to the table below for more details SETTINGS Effect 1 2 3 4 5 6 7 8 9 10 Sound 0 o o O O O O O Of 0 Auto O0 O O O O O O O O01 Strobe speed HIH Allon 0o O O O O O Of Of 1 OO FOR SOUND ACTIVE PROGRAMS 1 Turn the Sound sensitivity pot refer to fig 4 anticlockwise to 0 2 Turn up your music to the volume which will be used throughout the show 3 Then turn the sound sensitivity pot clockwise till the lighting effect moves to the sound of the beat 5 8 MASTER SLAVE MODE CONNECTIONS To connect multiple units in Master Slave mode you need to connect a 3 pin DMX lead Refer to Fig 7 from the DMX output socket of the master to the DMX input socket of the slave then from the DMX output socket of the first slave to the DMX input socket of second slave and so on and so forth Refer to Fig 10 SETTINGS You then need to set the unit to Master Slave mode by flowing these steps 1 Set the first unit to sound or auto mode as per the Stand Alone instructions 2 Set the rest of the units to DMX address 1 refer to DMX mode DMX CONTROLLER DMX MODE NOTE To determine the address required you should refer to your DMX controller s manual Do not forget to use a DMX terminator at the final output in the chain Do not forget to
6. itted to the product by the manufacturer 2 8 FEATURES Automatic mode Strobing mode Audio Activated with sensitivity control Master Slave linkable DMX 512 controllable 3 channels INSTALLATION CAUTION For safe mounting read the following instructions carefully e Use suitable hook clamps for hanging the lighting effect e Use a safety wire with a breaking strain of more than double the lighting effect e Do not look directly into the light source e Make sure the lighting effect has suitable ventilation as per the instructions below e This lighting effect is intended for indoor use only e To avoid electrical shock keep away from rain and moisture e Keep unit out of reach from children e E E e E E E E E E E E e E E oe E m NOTE Use washers and spring washers when attaching your hook clamp to the yoke 1 For installation of the hook clamps and safety wire please refer to Fig 3 2 This lighting effect must be 0 5m away from any flammable materials or any walls or ceilings 3 Do not block or inhibit the air flow from the ventilation vents Lightemotion have various hook clamps and safety wires suitable for your lighting effect Please contact your local dealer for more information Not included 3 8 MAINTENANCE amp PERIODIC CHECKS CAUTION Some maintenance and checks may require the product to be opened and should only be done by qualified p
Download Pdf Manuals
Related Search