User Manual
Contents
1. A The triangle with a lightning bolt warns about dangers such as electric shock Explanation of Symbols A A triangle with an exclamation mark indicates important instructions that must be followed A A triangle with the letter i marks special tips and notes for operating the device Important Safety Instructions Damages resulting from noncompliance with instructions in this manual void any warranties We do not assume liability for consequential damages We do not assume liability for damages to things or persons that result from improper handling or disregarding safety instructions In such cases all warranties are voided Do not perform voltage measurements during the recharge cycle The battery can explode and cause fatal injuries Dear Customers the following safety instructions and danger descriptions are meant to protect you as well as the device Please carefully read the following points Improper handling of any electrical device can lead to fire electric shock or injury In order to ensure safe operation please follow these guidelines e Follow all warnings and safety instructions in this manual e There are no maintainable parts inside this product Opening or disassembling the product voids both certification CE and warranties During operation avoid the following adverse environmental conditions Moisture or high humidity Extreme cold or hot temperatures Direct sunlight Dust flammable gases2. e the device shows visible damage e the device does not function anymore Please note A The product is maintenance free for you Inside the product are no parts that can be checked or repaired so do not ever open it except for changing the batteries as described in these operating instructions 8 1 2 Recharging the battery The power display battery symbol in the left upper corner of the LCD display shows the current charge of the Li ion battery If the battery is empty empty battery symbol turn off the device and connect it to the supplied power supply The status display appears red Once it turns off ca 2 3 h the battery is fully charged 29 A Only use the supplied battery and power supply as power source Using another battery or power supply can destroy the device Overloading the batteries by using an unsupported power supply can cause the battery to explode Please note Ensure that no dust or foreign particles can accumulate near the connectors of device and accessories since this creates fire or electric shock hazards Ensure that nobody steps on the power supply and that it cannot be squeezed especially near the plug or near the connection to the system 8 2 Cleaning Wipe the product with a clean dry cloth If the device is very dirty you can moisten the cloth with lukewarm water A Ensure that no liquids can get into the device Do not use any chemical cleaners since they could
3. Security Tech Germany TVAC10100 User manual Version 11 2009 Original English user manual Keep for future use 17 Introduction Dear Customer Thank you for purchasing this product This product meets the requirements of the applicable European and national guidelines The corresponding declarations and documents can be obtained from the manufacturer www abus sc com To maintain this condition and to ensure risk free operation you as the user must observe these operation instructions Before initial start up read through the complete operating instructions observing operating and safety instructions All company and product names mentioned in this document are registered trademarks All rights reserved If you have any questions please contact your installer or your local dealer A Disclaimer This user manual was prepared with greatest care If you should notice omissions or inaccuracies please inform us about these on the back of this manual given address The ABUS Security Center GmbH assumes no liability for technical and typographical faults and reserves the right to make at any time modifications to the product or user manual without a previous announcement The company is not liable or responsible for direct and indirect subsequent damages which are caused in connection with the equipment the performance and the use of this product No guarantee for the content of this document is taken 18
4. T 24 6 1 Menu guidant ERIT EO EE TENEO 24 6 2 MONOT SC URS MITT TETTE 25 6 3 PWS CONAN CUS OUI IS cprccesccy sens gorune a a a a aaa 25 7 Selecting the Measurement Procedure ssnsusnnnnnnunnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnn nnmnnn nnmnnn nnna 26 7 1 video nd audio EVEk aa Cm 26 Tic AC Vollage Tegel ell llb aseensatu ene eee eee ee en eer eee eee enn UM eee 26 7 9 DO voktage Measure MeNi eee eT ee ene o OO 27 7 4 AFLE S C 2r 7 5 CORNY LOSE eeen a E E A E EEEE E E E EE E i 28 7 6 COl SAIS To S e E E EE TUE UM MDES 29 8 Maintenance and Cl aning cccccsscssecceeesseeeseeeesseeeseeeesseeeseoeseeeeseoesnseeseoessseeeeooesseeeeeoossseessesssooensees 29 8 1 IVT IN sigle REI EE IIT EC 29 8 1 1 mee 29 9 1 2 Recharging the battery MED 29 8 2 GE MIN Gy MERE m MM 30 2 DISPOSA e 30 9 1 Cis ES NEU Em 30 9 2 Battery eoe MM 30 10 Technical SOCCIICANOINS uasssioniiccooueduseau iui sdiauE ue RaaaqwUUE Teva Ve RI 0 UD ds di yan adUEVwuiUdE s d aa aa iea ania VU USE 31 21 1 Proper use This ABUS test monitor can be used for configuring and installing video surveillance cameras It also allows you to test continuity soeed dome and power supply By attaching the test monitor to your wrist you have your hands free for installing and testing the ca
5. ate setting for the control signals Controlling the camera You can steer the camera with the arrow buttons Zooming the camera Zoom in Push the A and gt buttons simultaneously Zoom out Push the W and lt buttons simultaneously 7 5 Continuity test The test monitor enables you to test 2 cables for short circuits Connect the cables on one side to perform a continuity test Use the MODE button so select the continuity test mode cable test Connect the first cable to the right connector and or the second cable to the left connector of the terminal strip Cable 1 Cable 2 Cable1 NG Cable2 NG OK There is no interruption NG The cable shows an interruption 28 7 6 Color sample test The test monitor enables you to adjust the colors of a monitor Select the sample test menu item using the MODE button Now you can connect the black plug of the video cable to the input of a monitor An eight color standard test image appears on the screen PATTERN OUT D Push the V button to switch between the video standards NTSC or PAL 8 Maintenance and cleaning 8 1 Maintenance 8 1 1 Functional test Regularly check the product s physical state e g check for damage of the housing If you suspect that safe operation cannot be guaranteed anymore disconnect the product and ensure that it cannot be used by mistake Remove the batteries You can assume that safe operation is not possible anymore when
6. battery can explode and cause fatal injuries Ensure that no devices are attached while you perform a voltage measurement Connect the sensors to the appropriate monitor jacks Please ensure that the correct measurement procedure is selected The measurement range for direct current lies between 0 45 VDC AN Please pay attention to correct polarity With wrong polarity voltage measurement will not work The measurement results are displayed as follows C DC 0V 45V 7 4 PTZ control Select RS485 PTZ control via the mode button Connect the data cables of the speed dome with the terminals of the PTZ interface Pay attention to correct polarity Camera ID 1 PELCO P Baud Rate 9600 Sleep Mode Off Language German Reset gt Back gt Push the menu button to open the menu Push the VW button until you reach the settings for the RS 485 interface 2 Push the menu button again to open the submenu for the RS485 settings Use the A V buttons to navigate through the menu Keep pushing the menu button to open the respective subitem Use the lt gt buttons to change the settings for the respective subitem Use the menu button to confirm your change For correct operation of the speed dome the settings of the monitor s RS485 interface must match the speed dome settings e g Camera ID 1 identification number of the camera Pelco D Setting the control protocol to Pelco D or P Baud rate 4800 baud r
7. damage the housing surface or the screen discolorations 9 Disposal 9 1 General x O Devices with this marking should not be put in the household garbage Dispose of the product at the end of its lifetime according to the applicable regulations 9 2 Battery disposal Dispose of used batteries according to your local regulations Protect your environment 30 10 Technical Specifications Type number TVAC10100 Frequency range 50Hz 60Hz Functions Speed Dome test continuity test AC DC voltage measurement 400 mA during battery operation 2 5 A during charging mode 156 x 90 x 38 mm including protective cover 290 g 31
8. ench Dutch Danish The monitor is set back to the factory settings Select this menu item to go back to the main menu 25 7 Selecting the Measurement Procedure 7 1 Video and audio level e Turn the monitor on and select the video mode by pushing the mode button e Connect the yellow BNC plug of the video cable via the video extension cable to the video output of the camera If the camera supports audio connect the audio signal to the white plug of the video cable The monitor automatically recognizes video signal standards NTSC or PAL Use the A V arrow buttons to turn the audio input of the monitor on or off The display shows an info box with audio on audio off This info box shows the video signal level If you measure the video signal directly at the camera a voltage over 1 Vp p can occur The video signal level is higher to equalize losses over the cable distance 7 2 AC voltage measurement Do not perform voltage measurements during the recharge cycle The battery can explode and cause fatal injuries Connect the sensors to the appropriate monitor jacks Please ensure that the correct measurement procedure is selected The measurement range for alternating currents lies between 20 250 VAC Mode Select Mode 1 20 150 VAC Mode 2 150 250 VAC The measurement results are displayed as follows 26 7 3 DC voltage measurement Do not perform voltage measurements during the recharge cycle The
9. f you do not handle the battery properly it can explode and cause fire and or chemical burns e Do not expose the battery to fire or extreme temperatures such as direct sunlight in a vehicle in the sun or near a heat source e Donottry to dismantle the battery to repair it or to manipulate it in some other manner e Ensure that no short circuits occur at the battery Do not touch the battery contacts with any metal or other items e Ensure that the battery does not get damaged Do not transport or store the battery together with metallic items such as coins or keys If the battery is damaged do not use it any more Do not throw the battery drop it or subject it to strong impacts Do not place heavy items on the battery and do not apply any pressure to them Keep the battery away from liquids If you do not want to use the test monitor for a while remove the battery and store it in a cool dry place where it is out of the reach of children 20 Table of contents DEM 209 486 2 tot 22 MN IAC contents iste cette cei m 22 3 ee UNE SS and FUNCHONS tcm 22 As Description of th Device etm 23 4 1 Overview Type Number ssessssssesseeeeeeen nennen nennen nnns nhanh nnns nna nnn nna n nnns nna 23 4 2 MUTA NN oes eee cried mtn E E EN dI P GIRONE M EMEN FE EE 23 5 Description of the RYO NSN eere 23 5 1 Explanaton or the DEMOS ooocicesdeoehevb c Mucest eee a A REEE 23 ge Breieiejapeij s eps ele RTT T NUM 24 6 Au ART NER EE
10. lay errors This is not a malfunction and the LCD screen will work normal again when the environment temperature increases e Localized black dark or bright spots can appear and stay on the screen Such spots are normal for LCD screens and do not represent a malfunction In spite of high precision technology used in manufacturing a very small number of dark and permanently bright pixels is unavoidable After turning it off it is also possible that a distorted picture remains visible for several seconds WARNING BATTERY NOTES A Do not touch damaged or leaking batteries The test monitor contains a rechargeable lithium ion battery Leaking substances from the battery pack or burn residues can cause injury and damage the test monitor rendering it unusable Contact with such substances can lead to injury and chemical burns in eyes or skin Even if such substances are not immediately visible chemical processes can still cause damages later If you come into contact with a leaking battery or leaked out liquid follow these steps e Ifthe substance gets into your eyes do not rub your eyes Rinse your eyes immediately with clear water and seek medical help e fleaking battery acid comes into contact with your skin or clothing rinse the affected area immediately with clear water Seek medical help if the area gets inflamed or the skin becomes sore Please follow these instructions to avoid leakage of battery acid burns and explosions I
11. meras You can find an in depth functional description in chapter 3 Features and Functions Uses other than the ones mentioned above can lead to product damage or other dangers Any A other application is considered improper use and voids any warranties any liability is excluded This also applies if the product is modified in any way Please carefully read the entire operating instructions before using the product The operating instructions contain important information for installation and operation a ie M sensor EL ma protective cover n video cable 2 Package contents B l l 3 Features and Functions Simple installation of cameras and speed domes Possibility for testing cables Measuring AC voltage DC voltage and video signal Compact robust housing including protective cover Battery powered Test image generator 22 4 Description of the Device 4 1 Overview Type Number Type number TVAC10100 35 320 x 240 4 2 Unpacking Unpack the device with utmost care AN In case of damaged original packaging inspect the device first If the device shows any damage send it back with the packaging and inform the delivery service 5 Description of the housing 5 1 Explanation of the buttons rTT7 pM Hr M Mr m im ai i TENE nn D Status display Green ba
12. steam smoke or solvents Strong vibrations Strong magnetic fields as occur near machines or loudspeakers General Safety Instructions e Do not leave the package material lying around Plastic foil bags styrofoam parts etc can become dangerous play things for children e The test monitor has small ingestible parts and is thus unsafe for children Please keep device and accessories out of reach of children e Please do not insert anything through the openings of the device e Please follow the safety instructions and operating instructions of the connected devices e Inspect the device for damages before turning it on In case of damages please do not turn on the device e Ensure that no liquids or foreign particles can enter the device or the accessories Do not throw the device and its accessories do not let it drop do not step on it and do not subject it to heavy impacts 19 e Only use the supplied battery and power supply as power source Using any other battery can lead to fire and explosion e Ensure that no dust or foreign particles can accumulate near the connectors of device and accessories since this creates fire or electric shock hazards e Ensure that nobody steps on the power supply and that it cannot be squeezed especially near the plug or near the connection to the system Using the Power Supply LCD Screen Heavy pressure can destroy the LCD screen e Using the system in a cold environment can cause disp
13. ttery operation Hed power supply operation recharging Control buttons Arrow buttons for controlling the menu Menu button Menu for parameter settings Mode button Selecting the test mode Power button Turns the monitor on or off 23 5 2 Description of the connectors Cable1 G Rx Tx 5V Cable 2 O ISP interface Interface for firmware updates Power switch only the included power supply Continuity tester time protocol 6 Menu 6 1 Menu guidance Starting the OSD on screen display Opening sub menus Selecting a menu item for editing Confirming a selected value e Switching between menu items e Setting the values 24 6 2 Monitor settings Brightness Contrast Saturation Hue Brightness Setting brightness between 0 and 100 Setting image contrasts between 0 and 100 Setting color saturation between 0 and 100 Hue Setting hue between 0 and 100 only possible when monitor does not display anything Select this menu item to go back to the main menu 6 3 Miscellaneous Settings Camera ID 1 PELCO P Baud Rate 9600 Sleep Time Off Language English Recall gt Return gt Setting the speed dome camera ID Pelco Selecting the control protocol Pelco D or P Baud Rate Selecting the baud rate for data transfer 2400 4800 or 9600 bit s Sleep Time The monitor automatically turns off after a predefined time of inactivity Language Selecting the menu language English German Fr
Download Pdf Manuals
Related Search