English - Siqura
Contents
1. IG Installation Manual SURVEILLANCE SOLUTIONS Siqura HSD620PRH 62 IPRH Pressurized IP PTZ Camera with Day Night WDR Note To ensure proper operation please read this manual thoroughly before using the product and retain the information for future reference Copyright 2011 Siqura B V All rights reserved Siqura HSD620PRH and HSD621PRH 1 0 0 Installation Manual v1 0 113005 1 AIT5 4 MWO07SP2 Nothing from this publication may be copied translated reproduced and or published by means of printing photocopying or by any other means without the prior written permission of Sigura Sigura reserves the right to modify specifications stated in this manual Brand names Any brand names mentioned in this manual are registered trademarks of their respective owners Liability Sigura accepts no liability for claims from third parties arising from improper use other than that stated in this manual Although considerable care has been taken to ensure a correct and suitably comprehensive description of all relevant components the manual may nonetheless contain errors and inaccuracies Should you detect any errors or inaccuracies in the manual we would be grateful if you would inform us This helps us to further improve our documentation More information If you have any comments or queries concerning any aspect related to the product please do not hesitate to contact The Netherlands USA Corporate Hea2. 4 2 a 5 System initialization Switch 5 is mainly used to restore the camera s factory defaults 6 Camera upgrade Users must reset switch 6 after firmware upgrades are carried out RS 485 is the interface that enables communication between the Siqura HSD620PRH and HSD621PRH and its control device This means that the camera s RS 485 setup and that of the control device must be the same The RS 485 default setting is half duplex as shown in the figure below Please do not change the default setting without consulting a qualified specialist or supplier Half duplex Full duplex ON ON Iz ee RJ 485 settings Page 11 Siqura HSD620PRH 621PRH 4 4 Establishing a Network Connection To open communication with the Siqura HSD620PRH and HSD621PRH from a host PC and change the unit s network settings perform the following steps Step 1 Set the PC s network adapter to the unit s factory default subnet and connect the two devices Step 2 Access the unit from a web browser or other tool installed on the PC Step 3 Set the unit s IP address and subnet mask to the subnet it will be used in and reboot the unit To address the unit from the same PC again configure the PC s network adapter once more to assign the PC to the same subnet as the unit Step 1 Setting the host PC to the factory default subnet of the unit To configure the network adapter on the host PC In the Control Panel open Network Connections Ri
3. Ensure that a electrically connected components are carefully earthed and protected against surges high voltage transients caused by switching or lightning ESD Electrostatic discharge ESD can damage or destroy electronic components Proper precautions should be taken against ESD when opening the equipment Cautions Handle the camera carefully Do not abuse the camera Avoid striking shaking etc as the camera can be damaged by improper handling or storage Install electrical wiring carefully Ask a qualified electrician to perform the wiring for the installation Please note that input electricity to the unit is at a tolerance of 24VAC 50 60 Hz 10 Ground the camera appropriately to prevent electric shock or damage 24 VAC Ground GND 24 VAC Power input 3 pin terminal block Do not disassemble the camera To prevent electric shock do not remove screws or covers There are no user serviceable parts inside Please consult technical support if a camera is suspected of malfunctioning Do not operate the camera beyond the specified temperature humidity and power source ratings Use the indoor camera under conditions where the temperature is between 0 C 40 C 32 F 104 F Do not use strong or abrasive detergents when cleaning the camerd Use a dry cloth to clean the camera when it is dirty If the dirt is hard to remove use a mild detergent and wipe gently To clean the lens use lens tissue or a co
4. Fasten the pole thin direct mounting to a pole with the supplied stainless steel straps Fix the gooseneck tube to the pole direct mounting with the supplied screws and washers Attach the waterproof boot to the gooseneck tube Thread the cables through the gooseneck tube and the tube adaptor After threading the cables block the cable entry hole with the supplied sponge s to prevent insects from entering the tube Attach the lock screw plate to the back of the dome with the supplied screw as depicted in the section Ceiling mounting with a straight tube Adjust the waterproof boot to the junction of the gooseneck tube and the indoor tube adaptor Connect the cables to the dome camera Then attach the dome to the tube adaptor and fasten them together with the supplied screw Hexagon sere Plane washer Spring washer Stainless straps Pole direct mounting pole thin direct mounting gooseneck tube indoor tube adaptor waterproof boot 6 6 2 gt gt Dome Installation Pole thin wide box mounting Items Needed v v v v WT W Dome camera Gooseneck tube and other equipped items optional accessory Indoor tube adaptor for the Siqura HSD620PRH and HSD621PRH optional accessory Waterproof boot supplied with the indoor tube adaptor Pole wide box optional accessory Stainless steel straps optional accessory Tools Needed gt gt Stainless strap cutter Screwdriver To mount the dome camera with the pole box
5. Show icon in notification area when connected Notify me when this connection has limited or no connectivity Opening IP settings on the host PC Changing host PC IP settings to the factory default settings of the unit At this point connect your PC to the Siqura HSD620PRH and HSD621PRH You can connect them directly using a crossover cable or connect both to a switch Page 12 4 5 4 6 4 6 1 4 6 2 Dome Setup and Cable Connection Step 2 Accessing the unit Using a standard web browser you can now log on to the Siqura HSD620PRH and HSD621PRH s internal web server Step 3 Changing the unit s network settings The Network web page enables you to make the unit s network addressing compatible with the network it will be hooked into You can set a fixed IP address or have the IP address assigned by a DHCP server In the latter case open the Advanced Settings and enable DHCP Do not forget to save and reboot the unit after changing the settings System Compatibility To ensure system compatibility download the latest firmware from Support gt Software on the Siqura web site at http www siqura com Registration is required Dome Cable Definition and Requirements For operation the Siqura HSD620PRH and HSD621PRH cameras require either an Ethernet cable or an appropriate fiber optic cable to carry the signals to a remote viewing site and a cable to power the dome Cable Requirements For operation the camera requir
6. to prevent insects from entering the tube 6 Fix the outdoor tube adaptor to the straight tube with the supplied screws and washers Then adjust the waterproof boot to the junction of the straight tube and the outdoor tube adaptor 7 Connect the cables to the dome camera Then attach the dome to the outdoor tube adaptor and fix them with the supplied screw Wall Mount There are three types of wall mounts for the Siqura HSD620PRH and HSD621PRH dome camera gt Mounting with a mini wall mount as shown in the section Mini wall mount gt Mounting with a gooseneck tube as shown in the section Wall mounting with gooseneck tube gt Mounting with a wall box as shown in the section Wall box mounting Mini wall mount Items Needed Dome camera Mini wall mount and other equipped items optional accessory Screws and screw anchors not supplied Indoor tube adaptor for the Siqura HSD620PRH and HSD621PRH optional accessory Waterproof boot supplied with the indoor tube adaptor v v v v Ww Tools Needed gt Drill Screwdriver To mount the dome with the mini wall mount 1 Make a cable entry hole in the wall to recess the cables Otherwise cables can be threaded through the cable entry hole on the mount 2 Thread the cables through the mini wall mount and out through either the cable entry hole in the wall or the hole in the mini wall mount 3 Fix the wall mount to the wall with proper screws and screw anc
7. 4 84 Ibs Supplied with M8 16 screwx4 washerx4 spring washerx4 a a 4 Q Page 31 Siqura HSD620PRH 621PRH Page 32 PM01 Pole Thin Direct Mounting White Ivory 232 x136x60 mm 9 1 5 4 2 4 in Diameter 112 140 mm 4 4 5 5 in 0 7 kg 1 6 lbs Supplied with stainless steel strapsx4 M8 16 screwx4 washerx4 PM02 Pole Wide Direct Mounting White Ivory 270x170x60 mm 10 6x6 7 2 4 in Diameter 112 130 mm 4 4 5 in 1 kg 2 2 Ibs Supplied with stainless steel strapsx4 M8 16 screwx4 washerx4 a ST01 Stainless Steel Straps For fixing Pole Direct Mounting Pole Box on the pole Length 700 mm 27 5 in Width 0 63 0 02 kg 0 04 Ibs ST02 Stainless Strap Cutter For tension cut and crimp stainless steel straps 1 4 kg 3 1 Ibs Suitable for straps width 1 2 5 8 3 4 co co co Co Appendix A Camera Accessories 7 2 Siqura HSD620PRH and HSD621PRH Accessories PA02 Power Adapter optional gt Input 100 115VAC Output 24VAC 72VA US OR gt Input 220 230VAC Output 24VAC 72VA EU UK Note When wiring make sure the G Y wire Ground is inserted into the mid pin of the terminal block PA03 Power Adapter optional gt Input 110 115VAC Output 24VAC 72VA US OR gt Input 220 230VAC Output 24VAC 72VA EU UK Note When wiring make sure the G Y wire Ground is inserted into the mid pin of the terminal bl
8. and gooseneck tube l 2 SA 4 Fasten the pole wide box on a pole with equipped stainless steel straps Fix the gooseneck tube to the pole box with the supplied screws and washers Attach the waterproof boot to the gooseneck tube Thread the cables through the gooseneck tube and the tube adaptor Note After threading the cables block the cable entry hole with the supplied sponge s to prevent insects from entering the tube Attach the lock screw plate to the back of the dome with the supplied screw as depicted in the section Ceiling mounting with a straight tube Adjust the waterproof boot to the junction of the gooseneck tube and the tube adaptor Connect the cables to the dome camera attach the dome to the tube adaptor and fasten them together with the supplied screw Hamagon screw Pane washer Spring washer Stainless straps Pole box mounting pole wide box gooseneck tube indoor tube adaptor waterproof boot Page 27 7 1 IL SURVEILLANCE SOLUTIONS Appendix A Camera Accessories Before installing the camera compare your accessories to those listed in this section and ensure that you have all the parts you need for your installation Important If anything is missing do not install the dome Contact your supplier for assistance In This Chapter Mounting Accessories c cee eee eee een ne neni 29 Siqura HSD620PRH and HSD621PRH ACCESSOTieS cceeee eee 33 Mounting Accessories All mo
9. box mounting Items Needed v v v v WT v Dome camera Wall box mount and other equipped items optional accessory Gooseneck tube optional accessory Screws and screw anchors not supplied Indoor tube adaptor for the Siqura HSD620PRH and HSD621PRH optional accessory Waterproof boot supplied with the indoor tube adaptor Tools Needed gt gt Drill Screwdriver To mount the dome with the gooseneck tube and wall box l 2 3 A Fix the wall box to the wall with proper screws and screw anchors Fasten the gooseneck tube to the wall box with the supplied screws and washers Attach the waterproof boot to the gooseneck tube Thread the cables through the gooseneck tube and the tube adaptor After threading the cables block the cable entry hole with the supplied sponge s to prevent insects from entering the tube Attach the lock screw plate to the back of the dome with the supplied screw as depicted in the section Ceiling mounting with a straight tube Adjust the waterproof boot to the junction of the gooseneck tube and the indoor tube adaptor Page 23 Siqura HSD620PRH 621PRH 6 5 Page 24 gt gt Connect the cables to the dome camera Then attach the dome to the indoor tube adaptor and fasten them together with the supplied screw Hexagon screw Spring washer Plane washer Wall box mounting wall box mount gooseneck tube waterproof boot indoor tube adaptor Corner Mount With the co
10. dome camera and establishing switch settings In This Chapter Preparing the Siqgura HSD620PRH and HSD621PRH for Installation 9 SVC D O aaa aae a E 10 Communication Switch Configuration ccccceeesseeeeeeeeeeeee ees 11 Establishing a Network Connection ccccceeeeeeeeeeessseeeeeeeees 12 System Compatibility cc cccccce cece reece eee ee eeeeee ee enaeeee ees 13 Dome Cable Definition and RequireMents cccccceeeeeeee nena 13 Preparing the Siqura HSD620PRH and HSD621PRH for Installation This preliminary installation procedure is for the Siqura HSD620PRH and HSD621PRH dome cameras Perform the following steps to prepare the dome camera for installation 1 Unpack the dome package and take out the dome body 2 Loosen the screws that secure the bracket to the camera as indicated in the figure below Loosen these screws Tab Camera unit before bracket attached 3 Temporarily remove the screw indicated below 4 Assemble the bracket and rotate it into position 5 Replace the removed screw and then tighten all four screws Page 9 Siqura HSD620PRH 621PRH 4 2 Page 10 Loosen this screw Loosen this screw Temporarily Replace remove screw Tab and secure Removing the bracket Replacing the bracket Switch Definition It is necessary that the dome ID and communication protocol remain in the default modes when connecting the Siqura HSD620PRH and HSD62
11. the maximum level set by EU Directive 2002 95 EC or are exempted due to their application Page 5 3 3 1 CJ SURVEILLANCE SOLUTIONS Product Description The Siqura HSD620PRH and HSD621PRH high speed pressurized IP dome cameras are designed to deliver superb performance and durability with a pressurized housing Pressurization eliminates the effects of moisture dirt and pollution on valuable camera equipment This manual covers the installation of both the Siqura HSD620PRH and HSD621PRH IP cameras In This Chapter Produ C EOV OFV Wesa EE AANEEN EAEE ENA 7 General Operation Requirements ssssssssersnrrnrernrerrrnrrrnne 8 Package Contents sssssassssyamaonaaoiaiaaaa aaa aa a aa iaa 8 Product Overview Siqura HSD620PRH Features Outdoor High Speed Network PTZ dome Quad stream support Dual H 264 MPEG 2 MPEG 4 and MJPEG 26x optical zoom 12x digital zoom Day Night with IR cut filter Back Light Compensation Wide Dynamic Range 400 second preset targeting 360 endless panning 256 presets 8 programmable cruises 3 alarm in Two way audio 24 privacy masks Pressurized to 7psi able to hold pressure for up to 1 year Low pressure sensor Shrader and pressure relief valves standard IP 67 ingress protection v v v VT yv yv Yv wT yY yY YF YF YF YF WH Siqura HSD621PRH Features Quad stream support Dual H 264 MPEG 2 MPEG 4 and MJPEG 35x optical zoom 12x digital zoom Day Night with IR cut filter Wi
12. 1PRH cameras to other devices The switches used for configuring these settings are located on the bottom of the dome camera These settings are preset to operate the camera with the IP hardware Changing the settings may make the camera inoperative using the IP connection Refer to the figure and table below for switch location and definitions Siqura HSD620PRH and HSD621PRH switches Switch Definition Communication switch ISP connector for firmware upgrades RJ 45 SFP connector SD card slot Reset buttons mimi UIlLaOo wy gt 22 pin connector Note Switch E has two buttons Only the button closest to the 22 pin connector is used to restore factory server defaults The other button is reserved 4 3 Dome Setup and Cable Connection To restore factory server defaults gt Power up the camera while holding button E Continue to hold the button for 30 seconds after powering the camera Note The dome control protocol is set to Pelco D Do not change the dome control switches on the IP cameras Communication Switch Configuration The Siqura HSD620PRH and HSD621PRH s communication switch is specified in the table below The default settings are depicted in the figure You are advised to verify the accuracy of the communication switch configuration but do not change the default settings or some functions may not work properly Communication Switch Switch Description 1 RS 485 ON ae 2 3 Termination 4 Line lock
13. Bubble Dimension Weight POWER Power Power Consumption Appendix B Technical Specification Siqura HSD620PRH Siqura HSD621PRH H 264 BP MPEG 4 ES RTP UDP IP DHCP IGMPv2 RTSP S NTP MX IP HTTP SNMP v2 DiffServ SAP UPnP Indoor Outdoor Continuous 45 C to 50 C 49 F to 122 F 60 C Max N A 15 C 27 C 60 F 80 F IP67 CE FCC RoHS Polycarbonate glass filled Clear Polycarbonate 0 29cm 0 115 in thick 366 x 285 x 285 mm 14 4 x 11 2 x 011 2 in 5 kg 11 Ibs 24 VAC 80 W Note Weight and dimensions are approximate All specifications are subject to change without notice Page 37 www siqura com au member of the TKH Group lt www tkhsecurity usa com GROUP
14. MOUNTING ACCESSORIES 7 2 SIQURA HSD620PRH AND HSD621PRH ACCESSORIES 8 APPENDIX B TECHNICAL SPECIFICATION CJ SURVEILLANCE SOLUTIONS 1 3 3 4 5 7 7 8 8 9 9 a ee IW Ww Ww W WN FO pay e e oo N pay O No No N NM NY NH NH NN N FPF NY GW B WwW hHHReF OOO Oo O N O W N W O W Ul Page i od SURVEILLANCE SOLUTIONS Introduction Document scope This manual applies to Siqura s pressurized IP PTZ dome cameras the Siqura HSD620PRH and HSD621PRH It describes how to install and connect the Siqura HSD620PRH and HSD621PRH cameras Operation and configuration of the Siqura HSD620PRH and HSD621PRH cameras is covered in the user manual Intended audience This manual is aimed at installers and technicians involved in the installation of network devices such as the Siqura HSD620PRH and HSD621PRH Assumed skills and know how To work with the Siqura HSD620PRH and HSD621PRH camera an installer or technician must have adequate knowledge and skills in the fields of CCTV systems and components Electrical wiring and low voltage electrical connections Ethernet network technologies and Internet Protocol IP Windows environments Web browsers Video audio data and contact closure transmissions v v v v v Ww Video compression methods Specifications The information given in this manual was current when published Siqura reserves the right to revise and improve its products All specif
15. Output data rate Video settings On Screen Display OSD OPERATION Built in Protocol Pan Travel Tilt Travel Manual Speed Presets Preset Accuracy Preset Speed Cruise Sequence Auto Pan Privacy Mask Proportional Pan amp Tilt Resume after power loss Zone Title Home Function Auto Flip FUNCTIONS Motion detection Day Night IR Cut Filter Digital slow shutter Stabilizer PTZ coordinate data Directional OSD Wide Dynamic Range CONTACTS Inputs Alarm Reaction NETWORK Interface options Siqura HSD620PRH Siqura HSD621PRH D1 30fps H 264 D1 30fps MPEG 4 CIF 1fps MJPEG Up to 20 Mb s CBR or VBR selectable user profiles User profiles contrast brightness color saturation hue sharpness 3x text lines configurable position color border outline color font size 1x image in BMP GIF or JPEG format configurable position scaling Pelco D 360 endless 10 190 0 5 90 s 256 0 100 400 s 2 8 4 8 Black White Mosaic 3 levels Preset Sequence Auto pan Cruise Digital Mechanical Off On Off On Off On Off N A On Off 5Hz 10Hz Via API or Pelco D set get Compass direction Azimuth Elevation On Off On Off Ratio Shutter Iris levels 0 128 4 3 general 1 low pressure Preset Sequence Auto pan Cruise RJ 45 ltem Protocol GENERAL Environment Operating Temperature Heater activation Ingress protection Regulatory Housing
16. The equipment must be powered by a SELV power supply This is equivalent to a Limited Power source LPS see UL IEC EN 60950 1 clause 2 5 or a NEC Class 2 power supply When this module is operated in extremely elevated temperature conditions it is possible for internal and external metal surfaces to become extremely hot SELV conforming to IEC 60950 1 lt 60VDC output output voltage galvanically isolated from mains All power supplies or power supply cabinets available from Siqura comply with these SELV requirements Page 3 Siqura HSD620PRH 621PRH 2 2 Page 4 EMC The equipment has been tested and found to meet the CE regulations relating to EMC and complies with the limits for a Class B device pursuant to Part 15 of the FCC rules These limits are designed to provide reasonable protection against interference to radio communications in any installation The equipment generates uses and can radiate radio frequency energy improper use or special circumstances may cause interference to other equipment or a performance decrease due to interference radiated by other equipment In such cases the user will have to take appropriate measures to reduce such interactions between this and other equipment Any interruption of the shielding inside or outside the equipment could make the equipment more prone to fail EMC requirements Non video signal lines must use appropriate shielded Cat 5 cabling S FTP or at least an equivalent
17. afety Information Introduction The safety information contained in this section and on other pages of this manual must be observed whenever this unit is operated serviced or repaired Failure to comply with any precaution warning or instruction noted in the manual is in violation of the standards of design manufacture and intended use of the module Siqura assumes no liability for the customer s failure to comply with any of these safety requirements Trained Personnel Installation adjustment maintenance and repair of this equipment are to be performed by trained personnel aware of the hazards involved For correct and safe use of the equipment and in order to keep the equipment in a safe condition it is essential that both operating and servicing personnel follow standard safety procedures in addition to the safety precautions and warnings specified in this manual and that this unit be installed in locations accessible to trained service personnel only Safety Requirements The equipment described in this manual has been designed and tested according to the UL IEC EN 60950 1 safety requirements Warning If there is any doubt regarding the safety of the equipment do not put it into operation This might be the case when the equipment shows physical damage or is stressed beyond tolerable limits for example during storage and transportation Important Before opening the equipment disconnect it from all power sources
18. can be installed using a ceiling wall corner or pole mount In the following sections various installation methods and installation procedures are described in detail In This Chapter Dome DIMENSIONS cccceseceeesucueecueueucucvenuuueseucueneuvensuanenauues 19 Installation SCENaNOS serrera aaa aaa 19 COU MOUNE seriea rae E E E E E A A 20 WN alll POUT eaea E EEOAE OE ce 21 COrher MOUNCG araroa aa 24 POle MOUN E E 25 Dome Dimensions The Siqura HSD620PRH and HSD621PRH dome dimensions are 366 x 285 x 285 mm 14 4 x 11 2 x 11 2 in Installation Scenarios Choose your installation scenario from the list below for complete instructions for performing that installation Important Whatever your scenario always use the safety line when attaching the dome Ceiling mounts gt Ceiling mounting with a straight tube Wall mounts gt Mini wall mount gt Wall mounting with gooseneck tube gt Wall box mounting Corner mounts gt Corner Mount Pole mounts gt Pole thin wide direct mounting gt Pole thin wide box mounting For descriptions of the various accessories required for each installation see Appendix A Camera Accessories Note Some illustrations in this section use the term plane washer This is also Known as a flat washer Page 19 Siqura HSD620PRH 621PRH 6 3 6 3 1 Page 20 gt gt Warning Fully torque down the mounting bolt that attaches the WMO2 tube adapter to the mounti
19. d Indoor tube adaptor for the Siqura HSD620PRH and HSD621PRH optional accessory Tools Needed gt gt Drill Screwdriver To mount the dome with the gooseneck tube 1 i Make a cable entry hole in the wall to recess the cables Otherwise cables can be threaded through the cable entry hole on the mount Thread the cables through the mini wall mount and out through either the cable entry hole in the wall or the hole in the mini wall mount Fix the gooseneck tube to the wall with proper screws and screw anchors Attach the waterproof boot to the gooseneck tube Thread the cables through the gooseneck tube and the tube adaptor and lock it to the mini wall mount with the supplied screws and washers At this point the dome can be suspended from the mini wall mount using the safety wire 6 4 3 b gt Dome Installation Block the mount s cable entry hole with the supplied sponge s to prevent insects from entering the tube Attach the lock screw plate to the back of the dome with supplied screw as depicted in the section Ceiling mounting with a straight tube Adjust the waterproof boot to the junction of the gooseneck tube and the tube adaptor Connect the cables to the dome camera attach the dome to the indoor tube adaptor and fasten them together with the supplied screw Hexagon Spring washer Pendant Rubber washer screw tube washer Wall mounting gooseneck tube indoor tube adaptor waterproof boot Wall
20. de Dynamic Range Back Light Compensation Electronic Image Stabilization 400 second preset targeting 360 endless panning 256 presets 8 programmable cruises 3 alarm in Two way audio 8 privacy masks v v v v yv yv yv TF YF YF GF vy Page 7 Siqura HSD620PRH 621PRH 3 2 3 3 Page 8 General Operation Requirements A minimum of one control device is required for operation such as a control keyboard a DVR or a PC The Sigura HSD620PRH and HSD621PRH contains a built in receiver that decodes commands originating from a control device The built in Pelco D protocol provides connectivity to other surveillance systems and allows the Siqura HSD620PRH and HSD621PRH to be integrated with other suppliers surveillance systems For more detailed information see the Technical Specifications appendix Package Contents Before proceeding please verify that the box contains the items listed here If any item is missing or has defects do not install or operate the product Contact your supplier for assistance Siqura HSD620PRH and HSD621PRH Dome camera Pressurized housing Dome cover S E Ring Bracket Teflon tape Connectors Security TORX Quick start guide CD containing manuals 4 1 ino SURVEILLANCE SOLUTIONS Dome Setup and Cable Connection Before installing or connecting the Siqura HSD620PRH and HSD621PRH please refer to this section and complete the preliminary preparations for setting up the
21. dquarters US Corporate Offices Sigura B V TKH Security Solutions USA Inc Zuidelijk Halfrond 4 12920 Cloverleaf Center Drive 2801 DD Gouda The Netherlands Germantown Maryland 20874 USA General 31 182 592 333 General 1 301 444 2200 Fax 31 182 592 123 Fax 1 301 444 2299 E mail sales ni siqura com E mail sales us tkhsecurity usa com WWW www siqura com WWW www tkhsecurity usa com Contents 1 INTRODUCTION 2 SAFETY 2 1 SAFETY INFORMATION 2 2 CAUTIONS 2 3 REGULATIONS 3 PRODUCT DESCRIPTION 3 1 PRODUCT OVERVIEW 3 2 GENERAL OPERATION REQUIREMENTS 3 3 PACKAGE CONTENTS 4 DOME SETUP AND CABLE CONNECTION 4 1 PREPARING THE SIQURA HSD620PRH AND HSD621PRH FOR INSTALLATION 4 2 SWITCH DEFINITION 4 3 COMMUNICATION SWITCH CONFIGURATION 4 4 ESTABLISHING A NETWORK CONNECTION 4 5 SYSTEM COMPATIBILITY 4 6 DOME CABLE DEFINITION AND REQUIREMENTS 4 6 1 Cable Requirements 4 6 2 Verifying Ethernet connectivity 4 6 3 Connecting Aligning and Mounting the Camera 5 PRESSURIZING THE CAMERA 5 1 PRESSURE SWITCH CALIBRATION 5 2 PRESSURIZING 6 DOME INSTALLATION 6 1 DOME DIMENSIONS 6 2 INSTALLATION SCENARIOS 6 3 CEILING MOUNT 6 3 1 Ceiling Mounting with a straight tube 6 4 WALL MOUNT 6 4 1 Mini wall mount 6 4 2 Wall mounting with gooseneck tube 6 4 3 Wall box mounting 6 5 CORNER MOUNT 6 6 POLE MOUNT 6 6 1 Pole thin wide direct mounting 6 6 2 Pole thin wide box mounting 7 APPENDIX A CAMERA ACCESSORIES 7 1
22. e to the back of the dome with the supplied screw 8 Adjust the waterproof boot to the junction of the gooseneck tube and the indoor tube adaptor 9 Connect the cables to the dome camera Then attach the dome to the indoor tube adaptor and fasten them together with the supplied screw Spring washer Flat washer E Hexagon screw Corner wall mounting corner standard mounting plate gooseneck tube mini wall mount indoor tube adaptor waterproof boot Pole Mount There are two ways to mount the Siqura HSD620PRH and HSD621PRH cameras on a pole Using a thin wide direct mount as described in the section Pole thin wide direct mounting gt Using a thin wide box mount as described in the section Pole thin wide box mounting Pole thin wide direct mounting The dome can be installed to a pole with a thin wide direct mounting accessory and a gooseneck tube Page 25 Siqura HSD620PRH 621PRH Page 26 gt gt Items Needed v v v v v v Dome camera Gooseneck tube and other equipped items optional accessory Indoor tube adaptor for the Siqura HSD620PRH and HSD621PRH optional accessory Waterproof boot supplied with the indoor tube adaptor Pole thin direct mounting optional accessory Stainless steel straps optional accessory Tools Needed gt gt Stainless strap cutter optional accessory Screwdriver To mount the dome camera with the pole thin direct mounting and gooseneck 1 2 cy A
23. era s pressure sensor must be calibrated and the housing pressurized The Low Pressure alarm uses an absolute pressure sensor and must be calibrated to the local altitude 5 1 Pressure switch calibration To calibrate the pressure sensor Power up the unit The green LED located in the center of the camera bracket will turn on After 30 seconds the LED will begin to blink Press the red button located next to the LED LED will turn off indicating unit is calibrated Calibration is now complete The camera will store this base value and should not need to be recalibrated To recalibrate repeat the above procedure Note Alarm sensor contact is open when pressurized and closed when the enclosure is not pressurized The Sensor will activate open at 5psi and close at 1 psi Page 17 Siqura HSD620PRH 621PRH 5 2 Pressurizing To pressurize the Siqura HSD620PRH and HSD621PRH camera Set the gauge or regulator from 10 to 20psi 7 to 1 4bar Nitrogen Tank Place the air chuck on the tank valve and begin Sai l Air Chuck filling until pressure relief valve opens Open the relief valve Drain all air from the housing and 3 times to remove all moisture After purging check the housing pressure It should be around 5psi 34bar Page 18 6 6 1 6 2 A SURVEILLANCE SOLUTIONS Dome Installation Based on the installation environment the Siqura HSD620PRH and HSD621PRH cameras
24. es a video and cable harness as described below gt A cable to provide a 24 VAC power supply to the dome gt A Cat 5 Ethernet cable gt Optional cable for alarms Important Ensure the power supply corresponds with the dome s power requirement or damage will occur If any mistake happens contact a qualified technician Verifying Ethernet connectivity Refer to the following figure to determine whether you have established an Ethernet connection Ethernet socket LEDs green yellow Green on off 100 10 Mbit Yellow on blink Yellow off flash Page 13 Siqura HSD620PRH 621PRH 4 6 3 Connecting Aligning and Mounting the Camera Once you have configured the protocol and network switches connect the main cable to the base of the camera and make the appropriate connections gt To align mount the pressurized camera 1 Attach the cable harness to the camera Attaching cable to the pressurized camera 2 Secure the camera to the housing Securing the camera to the housing Page 14 Dome Setup and Cable Connection 3 Attach the dome to the housing Align the dome Secure the dome 4 Connect the cable as follows Brown 24VAC men IP connection configuration Page 15 Siqura HSD620PRH 621PRH Cable connection in a mini wall mount Page 16 Pressurizing the Camera 5 Pressurizing the Camera Before mounting the Siqura HSD620PRH and HSD621PRH cam
25. ght click the connection to be configured and select Properties In the items list select Internet Protocol TCP IP Click Properties In the Internet Protocol TCP IP Properties dialog click Use the following IP address Enter an IP address that will assign your PC to the same subnet as the unit i e within the 10 x x x range Use 255 0 0 0 as a subnet mask oP a ee a Important To prevent conflicts be sure to choose a unique IP address No two devices on a network can have the same IP address 7 To apply the new settings click OK and then click Close Local Area Connection 2 Properties Pk Internet Protocol TCP IP Properties a R General Advanced General Connect using You can get IP settings assigned automatically if your network supports this capability Otherwise you need to ask your network administrator for ES Intel R PRO 1000 GT Desktop Ada the appropriate IP settings This connection uses the following items Obtain an IP address automatically v A QoS Packet Scheduler Use the following IP address 3 Realtek LANPkt Protocol IP address Internet Protocol TCP IP v Subnet mask gt Description EN a Transmission Control Protocol Internet Protocol The default Use the following DNS server addresses wide area network protocol that provides communication across diverse interconnected networks Default gateway Preferred DNS server Alternate DNS server C
26. hors 4 Attach the waterproof boot to the mini wall mount 5 Thread the cables through the tube adaptor and lock it to the mini wall mount with the supplied screws and washers At this point the dome can be suspended from the mini wall mount using the safety wire 6 Block the mount s cable entry hole If the cable is threaded into the wall block the hole in the mount with the supplied plate If the cable is threaded through the neck of the wall mount block the cable entry hole with the supplied sponge s to prevent insects from entering the tube 7 Attach the lock screw plate to the dome plate with the supplied screw as depicted in the section Ceiling mounting with a straight tube 8 Adjust the waterproof boot to the junction of the mini wall mount and the indoor tube adaptor 9 Connect the cables to the dome camera Then attach the dome to the indoor tube adaptor and fasten them together with the supplied screw Page 21 Siqura HSD620PRH 621PRH 6 4 2 Page 22 gt gt D Ay D PLI J Mini wall mount Mini wall mount with secured cable entry plate Wall mounting with gooseneck tube The following figure shows how cables run through the tube Gooseneck with recessed left and exposed right cabling Items Needed v v v v v Dome camera Gooseneck tube and other equipped items optional accessory Waterproof boot standard accessory with the indoor tube adaptor Screws and screw anchors not supplie
27. ications are subject to change without notice Important information Before proceeding please read and observe all instructions and warnings in this manual Retain this manual with the original bill of sale for future reference and if necessary warranty service When unpacking your product check for missing or damaged items If any item is missing or if damage is evident do not install or operate this product Contact your supplier for assistance Page 1 Siqura HSD620PRH 621PRH Page 2 Typographical Conventions Before you start using this guide it is important to understand the typographical conventions used in the documentation The following kinds of formatting in the text identify special information Formatting convention Numbered list Special Bold Emphasis CAPITALS KEY KEY Type of Information Step by step procedures You can follow these instructions to complete a specific task Items you must select such as menu options command buttons or items in a list Used to emphasize the importance of a point or for variable expressions such as parameters Names of keys on the keyboard for example SHIFT CTRL or ALT Key combinations for which the user must press and hold down one key and then press another for example CTRL P or ALT F4 2 1 CJ SURVEILLANCE SOLUTIONS Safety In This Chapter Samy OFM Oi EATEN 3 UT IO IS ertereercpipnnett cocaine EAEE 4 PRU eG Sey cre ee ete eee 5 S
28. ng bracket to prevent any movement of the camera due to wind vibration etc Make sure the camera cannot move at all in its bracket after installation Any movement of the camera in its bracket can compromise positional accuracy Ceiling Mount There is one ceiling mounting option for the Siqura HSD620PRH and HSD621PRH outdoor dome cameras gt Ceiling mounting with a straight tube Ceiling Mounting with a siraight tube The only ceiling mount for the Siqura HSD620PRH and HSD621PRH dome cameras is the straight tube mount Ceiling Mount straight tube The straight tube is available in lengths of 25 cm and 30 cm Items needed 5 Dome camera 6 Straight tube and other equipped items optional accessory 7 Screws and screw anchors for fixing the straight tube onto the ceiling not supplied Tools needed 8 Drill 9 Screwdriver To mount the dome with a straight tube 1 Ensure that the ceiling can support the weight of the dome camera and straight tube 2 Make a cable entry hole in the ceiling Otherwise cables can be threaded through the cable entry hole on the tube 3 Attach the waterproof boot to the straight tube Fix the straight tube to the ceiling with proper screws and screw anchors not supplied 5 Thread the cables through the straight tube and the tube adaptor ne 6 4 6 4 1 gt gt Dome Installation Note After threading the cables block the cable entry hole with the supplied sponge s
29. ock Page 33 ltem CAMERA ios SURVEILLANCE SOLUTIONS Appendix B Technical Specification Siqura HSD620PRH Siqura HSD621PRH Image Sensor 1 4 CCD Optical Zoom Digital Zoom Effective Pixels Horizontal Resolution Electronic Shutter Synchronization Video Output S N Ratio Minimum Illumination Focal Length Focus Mode White Balance Iris Control AGC Control Backlight Compensation VIDEO Number of video streams Frame rate Compression algorithm RESOLUTION Type of streaming Number of output streams Video Motion Detection Encoding latency GOP structure Frame rate 26x 35x 12x 380k 440k 540 TVL 1 1 10 ks 1 30 k s Internal Line Lock 1 0 Vpp 75Q RJ 45 SPF 1 0 Vpp 75Q0 BNC gold plated center pin gt 50 dB AGC off 0 09 lux 0 01 lux B W 0 1 lux color 0 01 lux B W 3 5 91 mm 3 4 119 mm Auto Manual Auto Manual Auto Manual Auto Manual On Off 2x H 264 2x MPEG 4 MPEG 2 and or MJPEG 1 to 30 fps H 264 BP ISO IEC H 264 BP ISO IEC 14496 10 MPEG 4 SP Layer 14496 10 MPEG 4 SP Layer 5 ISO IEC 14496 2 MJPEG 5 ISO IEC 14496 2 MPEG 2 ISO IEC 13818 2 MJPEG UDP IP multi and or UDP IP multi and or unicast unicast TCP IP RTP over RTSP Up to 20 Yes user defined masking lt 130 ms typ IP selectable user profiles 1 to 30 fps Page 35 Siqura HSD620PRH 621PRH Page 36 ltem Quad streaming
30. rner standard mounting plate and gooseneck tube mini wall mount the Siqura HSD620PRH and HSD621PRH can be mounted onto the corner or a wall Items Needed Dome camera Gooseneck tube mini wall mount and other equipped items optional accessory Corner standard mounting plate optional accessory Indoor tube adaptor for the Siqura HSD620PRH and HSD621PRH optional accessory Waterproof boot supplied with the indoor tube adaptor Screws and screw anchors for fixing the corner standard mounting plate not supplied v v v v v wv Tools Needed gt Drill Screwdriver To mount the dome camera with the corner standard mounting plate and gooseneck tube mini wall mount 1 Makea cable entry hole on the wall to recess the cables Otherwise cables can be threaded through the cable entry hole on the tube 2 Fix the corner standard mounting plate on a corner with the proper screws and screw anchors 3 Attach the gooseneck tube mini wall mount to the fixed mounting plate with the supplied screws and washers 4 Attach the waterproof boot to the gooseneck tube mini wall mount 5 Attach the indoor tube adaptor to the gooseneck tube mini wall mount 6 6 6 6 1 Dome Installation 6 Thread the cables through the gooseneck tube mini wall mount and the indoor tube adaptor Note After threading the cables block the cable entry hole with the supplied sponge s to prevent insects from entering the tube 7 Attach the fixing plat
31. tton tipped applicator and ethanol DO NOT clean the lens with strong detergents 2 3 Safety Never face the camera towards the sun Do not aim the camera at bright objects Whether the camera is in use or not never aim it at the sun or other extremely bright objects as this can damage the camera Regulations This device complies with Part 15 of the FCC Rules Operation is subject to the following conditions gt This device may not cause harmful interference gt This device must accept any interference received including interference that may cause undesired operation This symbol on the product or on its packaging indicates that this product shall not be treated as household waste in accordance with Directive 2002 96 EC Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment By proper waste handling of this product you ensure that it has no negative consequences for the environment and human health which could otherwise be caused if this product is thrown into the garbage bin The recycling of materials will help to conserve natural resources For more information on how to recycle this product please contact your local city office your household waste disposal service or the seller of the product Compliance is evidenced by written declaration from our suppliers assuring that any potential trace contamination levels of restricted substances are below
32. unting accessories are optional To secure the camera to the tube or wall mount all tube mounts and the mini wall mount are supplied with the following gt Cup washer 1 gt 8mm spring washer 1 gt 8mm rubber gasket 1 gt M8 12 screw 1 Waterproof boot 1 WMO03A Gooseneck Tube White Color Iron 298x385 mm 11 73 15 56 in 2 1 kg 4 6 Ibs Gasket plate and cable gland for IP66 rated installations included Page 29 Siqura HSD620PRH 621PRH WM01A Mini Wall Mount White 184x104x115 2 mm 7 24 4 09x4 54 in 0 6 kg 1 2 lbs Gasket plate and cable gland for IP66 rated installations included 2a T4 i Cy z birn PM05 Swan neck Mount White Iron Height 250 500 mm 9 8 19 7 in Diameter 50 mm 2 in 1 kg 2 2 Ibs 1 8 kg 4 Ibs CM01 250mm CM02 500mm Straight Tube White Iron Height 250 500 mm 9 8 19 7 in Diameter 50 mm 2 in 1 kg 2 2 Ibs 1 8 kg 4 Ibs Page 30 Appendix A Camera Accessories WM05 Corner Standard Mounting Plate White 222x204x117 mm 8 7x8x4 6 in 2 kg 4 4 lbs Supplied with 8mm washer x4 spring washerx4 M8 16 screwx4 M8 nutx4 gt 3 sah f PM04 Pole Wide Box White Ivory 270x166x155 mm 10 6x6 5x6 1 in 3 2 kg 7 1 Ibs Supplied with M8 16 screwx4 washerx4 spring washerx4 stainless steel strapsx4 WM06 Wall Box Mounting Ivory 270 L x166 W x95 D 10 6x6 5x3 7 in 2 2 kg
Download Pdf Manuals
Related Search