Fermentation Vessel Control and Automation
Contents
1. 50 SCC Modules 396 00 396 00 Shielded Data Transfer Cable 99 00 99 00 Power Cable 4 50 4 50 Shipping 43 47 55 00 Project poster and materials 25 00 25 00 w Tre POROE Subtotal 2 732 97 2 592 50 Software LabVIEW None None Labor at 10 50 hour a Arndt Andrew 2 031 75 b Daters Adam 2 037 00 c DeSerano Bradley 2 121 00 d Striegel Austin 2 194 50 Subtotal 8 384 25 Total 2 732 97 10 976 75 Due to a decrease in the cost of hardware and lowered project hours the total project cost has been lowered by approximately 525 22 5 Scheduling The project schedule went through some slight modifications since the initial planning of the project These resulted from new insight into the appropriate time frame for each task This evolved from team member insight and understanding of LabVIEW as well as re thinking start dates for tasks to deliver a better project The changes can be seen in stand alone versions of the original and updated schedules which appear in Figures 5 and 6 respectively The project deliverable schedule is located below in Figure 7 23 Maniac Ferney Meen Apri f re August T Segtenbe October Wovenber Decenas sa 6 312118 28 AA W i IIA IO 131302713 Ie 17 0 l 1522 29 IS 12 10188 13 00 17 Pr sben Detintion Pratt Detin Erud Used inet kit Corte art Mer de kar Communication wi Chert and Airo Teshevobogy omde ation amp Selection erg syn of Posutse Technologies k2. National Instruments nor shipping costs Also the cost of the oxygen concentration meter was also decreased due to an academic discount 4 4 Financial Requirements The financial requirements are the consolidation of the monetary costs of all resources personnel parts service etc that are needed to complete the project This includes not only the costs relating directly to the final product itself but also any and all costs incurred during the planning and implementation of the project The tables below show this information with and without the calculated cost of labor The cost of labor used was an hourly rate of 10 50 21 Table 5 Original Financial Requirements la temo WOLabor With Labor Parts and Materials a Oxygen Concentration Meter 1 500 00 1 500 00 b Data Acquisition Unit Signal Conditioning Unit Cables Project poster and materials Software LabyIEWY Labor at 10 50 hour a Arndt Andrew b Daters Adam c DeSerano Bradley d Striegel Austin 400 00 400 00 700 00 700 00 130 00 130 00 25 00 25 00 Subtotal 2 755 00 2 755 00 None None 2 131 50 2 142 00 2 236 50 2 236 50 subtotal 0 746 50 Total 2 755 00 11 501 50 Table 6 Revised Financial Requirements Memo WO Labor WithLabor Parts and Materials Oxygen Concentration Meter 1 487 00 1 335 00 RS232 to COM Port Cable 30 00 30 00 Data Acquisition Card 427 50 427 50 SCC Carrier Box 220 50 220
3. Test Documentation sss 29 Figure 23 Intended Lief SUV do adapta 30 iii List of Tables Item Page Table 1 Original Personal EOI ES EG AE ES v e eid ete 20 Table 2 Revised Personal Effort nn tue aded c du adiac Ee 20 Table 3 Original Other Resources Required ici iii dt dt 2 Table 4 Revised Other Resources Requisitos 2 Table 5 Original Financial Reduireniente ss pe een acer tov eem tee poe Cue edis edo ee Ee 22 Table 6 Revised Financial Requirements ener enne nnne ens 22 iv List of Symbols None List of Definitions COM Serial communications port DAQ Data acquisition Flash Animated graphics technology and format from Macromedia which can be viewed with a web browser plug in GUI Graphical user interface VO Input output LabVIEW Laboratory Virtual Instrument Engineering Workbench PCI Peripheral component interconnect PPM Parts per million PXI PCI extensions for instrumentation RPM Rotations per minute RS232 Standard for serial cable interface SCC Signal conditioning system offered by National Instruments SLM Standard liters per minute USB Universal serial bus VI virtual instruments Sub unit program in LabVIEW that represents the appearance and function of a physical implement vi 1 Introduction Materials This section will introduce the project including the executive summary acknowledgements problem statement and solution operating envir
4. and hardware The team decreased the amount of time for end product design and end product prototype implementation Both of the tasks were simply overestimated based upon lack of knowledge of LabVIEW After researching more about LabVIEW less time would be required to design and implement the end product Other Resource Requirements Other resource requirements entail all those resources that are not associated with personnel effort or financial resources These resources may include parts materials and services required throughout the project as well as support for test and measurement equipment The tables below outline the original and revised other resources for this project 20 Table 3 Original Other Resources Required Parts and Materials Oxygen Concentration Meter Data Acquisition Unit Signal Conditioning Unit Cables Project poster and materials Software LabVIEW Totals Table 4 Revised Other Resources Required Parts and Materials Oxygen Concentration Meter R5232 to COM Port Cable Data Acquisition Card SCC Carrier Box SCC Modules Shielded Data Transfer Cable Power Cable Shipping Project poster and materials Software LabVIEW a 00000000 TJE TORQO T e e O0O000000060 e Totals The revisions made between the other required resources reflect an overestimation of the estimated cost of the hardware The original costs did not figure in the academic discount given by
5. be used on any other equipment that is not supported 1 6 Assumptions and Limitations Certain aspects of this project need to be constrained to more specific terms In the individual assumptions and limitations sections more specific details will be developed to better outline the project 1 6 1 Assumptions To adequately develop this product certain assumptions about the project have been developed These assumptions were stated as follows The end user of this project will be someone who is familiar with the fermentation process Only one experiment will be conducted at a time Environmental stability of 2059 Sweeney will be maintained All new components and cables will be paid for by the client The end user understands basic computer terminology double click scroll etc All laboratory components will operate within their given rated power values A computer will be supplied by the client with LabVIEW and Excel already installed An extra PCI slot will be available on the computer for data acquisition card The data acquisition card will supply its own clock 1 6 2 Limitations A number of limitations have been imposed upon the project including the following File format type is in Excel Format Software shall be written using LabVIEW One sample per second must be recorded from each specified device Maximum flow rate for the air nitrogen must be less than 6 SLM Motor speed must be kept less than 600 RPM Safety glasses mus
6. eter t ER dede n i ende LE vi 1 Introduction Materials e M 1 Dl Exec tive SUI o Neza 1 a e o AA O e euo e an ug 2 1 37 Problem A e E A M M C MR 2 1 3 T Problem Statemelt eus es N p c Pa deed rbd 2 15 2 Problem SoIUtiOD des dicte A bte 3 1 4 Operator a ti PER IRR ee Ee pen Een ue 4 1 5 Intended User s and Intended Uses nn o eni ront 4 1 513 o to pd 4 1 52 Antended SECS eb DE e i Cala tu Mc d da 4 1 6 Assumprons and imitations uoce o e ehe he das De 4 ROT ASSUMP EONS ciae tri iren bere Uis cdi bebo a fet Ud ca da Pede 5 A o EE De to SS rabat drap not ua bte eta uade ON 3 1 7 Expected End Product and other Deliverables idos 5 2 Design AP PLO Achy inane op oett s 6 2 1 Desiett OBJeCtlVes n GE etes vitii edes riti deut a immu Ee De Ge ee Ke A ek 6 2 2 Functional REQUIEM i su sin hd Ee 6 2 3 Desin Constraints do eM tt D e f T 2 4 Technology Considerations and Results essere 8 24 1 Data Acquisition Borda ente EE AG SE trabe qd sd oat gr NE pe n 8 2427 Signal Conditiomitipi dad 8 2 4 3 Oxygen CONCESIONES Pda Enea encase 9 203 Testing Approaches nd dr dale alanis 10 2 6 Project Gonti miat off ce ee vipat RS ORI tele A RU UV EAT MARE 11 3 Detal ed Desin ees ee esee A 1 3 1 Oxygen Concentration Meter oie sesse as 12 3 2 Miss Gas Flow Metef st EE tod epe tds O wei denm Meum eg e buit tuts 13 3 3 Signal Conditioning Carrier cse etos GE e e Rc td DE NN REN 14 3 4 S
7. have a user manual detailing operation Oxygen Concentration N Meter RS232 Interface Mass Gas Flow i P Data Acquisition Signal Conditioner gt Meter Board Stirrer Motor A Control Data Acquisition Data Collection and Software Interaction Figure 4 Process Model of Functional Requirements 2 3 Design Constraints The entire project will be designed and constructed to perform under the following conditions and constraints Software environment The software developed for this project will be developed in LabVIEW This includes creating a GUI for user interaction Measurement collection timing The measurements from the lab equipment will be recorded at one sample per second Max air nitrogen gas flow rate The maximum air nitrogen gas flow rate shall be less than 6 SLM Max motor speed The maximum motor speed will not exceed 600 RPM If this is exceeded vibration problems may occur with the system Electrical isolation on stirrer motor control The voltage signals from the stirrer motor control must be electrically isolated Oxygen Concentration Meter The oxygen concentration meter must be able to measure between 0 and 9 5 PPM of dissolved oxygen and must be able to interface with LabVIEW 2 4 Technology Considerations and Results For this project there are four main areas for technology considerations These areas include the data acquisition board for collecting data signal conditioni
8. in a configuration as shown in Figure 12 Figure 12 also shows the connector block diagram of the SCC carrier unit As can be seen the SCC carrier unit can hold up to 20 SCC modules which can be either analog or digital signals This will allow for future upgradeability for the mock fermentation vessel collection system J1 J8 8 T x Single stage sa SCC Modules i nis on Analog SCC 7 oot Er J9 J 16 s ri A Dual staga conditioning of analog inputs or B DIO Signal Modules oF Xaojg guar Mang om ma C6 TEN Se RES Figure 12 Analog Input SCC Configuration left Diagram of Module Layout in SC 2345 Connector Block The SCC carrier will connect with the DAQ board through the use of a 68 pin shielded connector cable This cable is the NI SHC68 68 that is specifically used for connection to M Series DAQ boards section 3 5 The cable is shown in Figure 13 The cable comes in many lengths from 0 5 to 10 meters in length but a length of 2 meters was chosen to allow for easy spacing of PC away from the mock fermentation vessel The cable comes at a cost of approximately 99 and will be purchased from National Instruments Figure 13 NI SHC68 68 Connection Cable Stirrer Motor Control The current stirrer motor control of the mock fermentation vessel is a component of the Glas Col GKH Stir Tester 099D HST20N shown in Figure 14 This control unit offers two output signals that represent torque oz in
9. not worth the extra cost Signal Conditioning Technology considered Signal conditioning plays a huge role in obtaining reliable analog output from lab equipment Therefore in the design the team needed to explore equipment transients and other noise within the lab environment Results from contacting equipment manufacturers inquiring upon signal integrity of the output yielded an effective approach to signal conditioning For the stirrer motor control unit two scaled voltage signals would require electrical isolation up to 143Vrms due to a floating ground This floating ground will provide fast transients which will need to be filtered out To get accurate signal conditioning National Instruments was contacted for a recommendation for equipment Following their recommendation and an online advisory tool many signal conditioning modules were found having varying input with voltage ranges from 50mV to 42V 2 4 3 For the mass gas flow meter unit the output the output signal took the form of a current ranging from 4 to 20mA This output provided the choice of working with the current directly or converting to a 0 to 5V signal Working directly with the current would decrease the amount of equipment needed to purchase but could not be hooked up directly to the DAQ board By converting the current into a 0 to 5V signal the unit could easily hook up to the DAQ board but would at increased cost of a conversion module An additional conside
10. team has collected from the problem statement will be used to design the automated collection system The following is a list of objectives that the team will use to build this system e Ease of use The software developed for the automated collection system will be easy to use and is simple enough for most users to operate e Reliability The automated collection system will accurately capture the appropriate data from repeated use by various users e Dynamic The system will provide real time information to the user in of the form a real time display and will provide access to the data through file storage in Excel format Functional Requirements The following functions will be implemented into this project and are required to complete this project successfully These requirements were specified by the client as well as the faculty advisor and are modeled in the process model in Figure 4 Data acquisition The system will be able obtain measurements of speed torque air nitrogen gas flow and oxygen concentration from the appropriate measurement devices This system will apply proper filtering on the equipment output to obtain accurate measurements Data collection The measurements obtained will be recorded every second This information is stored in an Excel file format and available for user download Software interaction A GUI will display real time information and will be developed in LabVIEW It shall be easy to use and will
11. the full scale of dissolved oxygen 0 9 5 PPM a 200 point data logger for storing measurement information and a RS232 bidirectional link for connection to a PC or printer This model is shown in Figure 6 to the right This meter will be purchased in a kit that will provide the Figure 6 Orion 3 Star Meter meter probe probe stand and calibration materials for an approximate cost of 1335 This unit can be purchased from a number of different retailers but VWR Scientific was a recommended dealer from the manufacturer so they will be used for purchasing In order to utilize the RS232 bidirectional link for data logging an additional conversion cable must be purchased to interface with the PC The connections diagram shown in Figure 7 below shows that the RS232 connection to the meter is a 3 5mm stereo jack connector The conversion cable will convert this interface into a COM port which can be connected with the serial port of the PC used This conversion cable will have an approximate cost of 30 and will be purchased from VWR Scientific with the oxygen concentration meter 12 3 2 Reference Cond RS232 Power L pH or ISE ATC Stirrer jack 8 pin stirrer or DO BNC DO Ground Auto stir probe 9 pin Figure 7 Rear connections of Orion 3 Star Meter To interface with LabVIEW the team will use the onboard serial port for data acquisition from the oxygen concentration meter The meter will be configured to transfer data continu
12. A rai tas 28 A Du st as Ss 28 APPO ici ho e diia 29 11 List of Figures Item Page Figure 1 Mock Fermentation Vessel Apparatus nn lucccucccnec esse once cen e ce ene cover eve cana ee Ge conc tenants eaae 1 Figure 2 Control flow of system Interaction jani dr 2 Figure 3 Prototype CUL dd dada 3 Figure 4 Process Model of Functional Reguirement iese se aa n se ee ne ee ee AR GR AR GRA Ge ee ee ee 7 Figure 5 The basic flow diagram of the MA A eet dean ee 12 Figure 6 Orion a A e dua 1 Figure 7 Rear connections of Orion 3 Star Meter esse ese ee se se eene enne 1 Figure 8 Omega PMA S000 Series soii desc 1 Figure 9 NI SCC IC20 Current Input Module a 1 Figure 10 Omega FMA 5610 Connector Diagram NI SCC IC20 Current Input Module Wiring A a al x Pec A aa cae ats di pde a DONC a ee Ee EG 1 Figure ll SCC caret SAD boss kte SA and ea ht Sena d as 14 Figure 12 Analog Input SCC Configuration Diagram of Module Layout in SC 2345 Connector EN Ne ERE Oda 1 Figure 13 NI SHC68 68 Connection Cable ping arsi ner i 1 Figure 14 GRO Sr Teta A n eds 1 Figure 15 NI SCC AI Series Isolated Analog Input Module Wiring Block Diagram 16 Figure 16 NT PCI 6221 DAQ Boatdzaso ss GE e e 1 Figure 17 Initialization Screen iii dic 1 Figure 18 Real time Display SEA pio A A AAA AR 1 Fieure 19 Original Project a o o 24 Figure 20 Revised Project SEO Ee iu e GR EG De 25 Figure 21 Deliverable Soberana di 26 Figure 22 Team Standard
13. Fermentation Vessel Control and Automation Design Report Team Dec06 07 Client Stephanie Loveland ISU Department of Chemical and Biological Engineering Faculty Advisor Dr Degang Chen Team Members Andrew Arndt Adam Daters Bradley DeSerano Austin Striegel Report Disclaimer Notice DISCLAIMER This document was developed as a part of the requirements of an electrical and computer engineering course at lowa State University Ames lowa This document does not constitute a professional engineering design or a professional land surveying document Although the information is intended to be accurate the associated students faculty and lowa State University make no claims promises or guarantees about the accuracy completeness quality or adequacy of the information The user of this document shall ensure that any such use does not violate any laws with regard to professional licensing and certification requirements This use includes any work resulting from this student prepared document that is required to be under the responsible charge of a licensed engineer or surveyor This document is copyrighted by the students who produced this document and the associated faculty advisors No part may be reproduced without the written permission of the senior design course coordinator March 31 2006 Table of Contents o Sun A A 111 A A E O ES a iv A e bite pa tele eec Uer dete ucc dede Ses DAR Tcu DA re a V ESO Definitions ood ade
14. and speed RPM in the form of analog voltage signals The voltage signals are scaled signals which for every 1mV measured they are either 1 oz in of torque or 1 RPM of speed respectively There a few design issues that need to be taken into account when trying to measure these signals for data acquisition The unit operates with a floating ground that typically operates at 70 to 15 3 5 90V Also 60V fast transient spikes could appear on the output lines due to the switching DC motor that is driven by the motor control In order to measure the torque and speed accurately signal conditioning must be applied to ensure signal integrity To achieve proper conditioning an isolated analog input module will be used from National Instruments The SCC AI Series modules from National Instruments offer varying input voltage ranges from 50mV to 42V As discussed earlier the team selected an input voltage module with an input range of 0 to 5V This module is the NI SCC AI04 which offers two channels of isolated analog input with isolation up to 300V and differential input In order to connect the stirrer motor control to the module standard wire will be used to connect differentially to each channel of the module This will protect against the fast voltage transients and will offer better noise rejection Figure 15 below shows the wiring block diagram for connecting the SCC A104 This SCC AI04 module will be plugged in the signal conditioning carri
15. clock supplied on board the DAQ board each channel of input can be sampled and have data acquired In the current configuration proposed the DAQ board will have 6 of its 16 analog input channels used for sampling and data acquisition These 6 six channels will represent the 3 differential pairs of signals for mass gas flow torque and speed The additional input and output channels can be used for future expanding or controlling of external devices To interface with LabVIEW the team will take advantage of the available express VI s that are currently available to define the operation of the card With these express VPs scaling can be applied to account for the various signals that will be inputted Also these express VI s will aid the team in not having to create new LabVIEW code to define the operation of the DAQ board Software Interfacing A graphical user interface GUI will help students navigate the integrated data acquisition system for the mock fermentation vessel The prototype design of the GUI consists of three separate but cross referenced screens When starting the mock fermentation vessel experiment a user will access the GUI via an icon the desktop of the computer located in the lab The first screen that Mock Fermentation Vessel E gt periment Initialization Screen appears shows several initialization fields for mmn sm student input Figure 17 EE illustrates the preliminary f f VO design of
16. d file storage capabilities of the LabVIEW program Overall the GUI will be tested for errors and for proper displaying of all information This phase of testing will be carried out again by the team using the standard form found in appendix and used in the first phase To move on to the last phase of testing the team will evaluate the system by running through a mock experiment and verifying results of output to those expected The team will then review the testing data from this phase with the client and then the final decision to move onto the final phase of testing will be made 10 2 6 Third phase beta testing This phase involves having the client and potential users test the software and report problems to the team For testing the system four students will be asked to use the software and fill out a survey after trying out the system This survey can be found in appendix The survey will consist of opinions on ease of use functionality presentation and usability of the data exported These will be rated on a 1 to 5 scale and a section for comments will follow each section Also a section for suggestions appears at the end for additional comments The client will also be asked to use the software and fill out the survey After the team has received comments from the client and student testers the appropriate changes will be made to the software Another four students will be asked to use the software and fill out the survey This wil
17. e experiment is being performed Figure 18 Real time Display Screen When the experiment completes one more conclusion screen will appear in the form of a pop up window This pop up will signal the end of the experiment run time but will not close the real time display in case further experimentation is to be carried out This conclusion screen will show a restatement of initial inputs plus the file extension for where the file of in Excel spreadsheet form can be found Users will also be able to access the Excel formatted data via this screen as well 4 Resources This section details the financial personnel and other resources that will be required in order to complete the project 4 1 Task Definitions This section details the task definitions for each performed throughout the project 4 1 1 Task 1 Problem Definition Understand the functionality of the product Define the operation of the product and identify constraints Consult with advisor about the feasibility of the project 18 4 1 2 4 1 3 4 1 4 4 1 5 4 1 6 4 1 7 4 1 8 Task 2 Technology Considerations and Selection List the choices of technologies that can be used in the product design Contact manufacturers for product specifications and information and select the best and most feasible approach Task 3 End Product Design Construct a series of VI s that define the functionality of the technology selected Task 4 End Product P
18. er for interaction with the PC and LabVIEW Additional information on the signal conditioning carrier can be read in section 3 3 Figure 14 GKH Stir Tester E Senex ar haar Makita clon gras ECE Alum DAD Daiwa Snima 4 i i 4 um E CHX AVSENSE AND i i i LFF RO CAMA Figure 15 NI SCC AI Series Isolated Analog Input Module Wiring Block Diagram The NI SCC AI04 isolated analog input module will be purchased from National Instruments at an approximate cost of 265 50 Data Acquisition Board The selected data acquisition board is the National Instruments NI PCI 6221 M Series data acquisition board This DAQ board offers many features including 16 analog inputs 2 analog outputs 24 digital I O lines and two counters timers This DAQ board is shown at the right in Figure 16 This unit offers 16 bit resolution which correlates to an Jl accuracy of 70uV The sampling rate of the board is Figure 16 NI PCI 6221 DAQ Board 16 3 6 250 kilo samples sec which will provide an adequate signal sampling for the analog input signals This board will be purchased from National Instruments at an approximate cost of 427 50 In order to gather information from the SCC carrier and the signal conditioning modules the DAQ board will connect to the SCC carrier via the NI SHC68 68 shielded cable discussed in section 3 3 This cable will transfer the various analog input channels to the DAQ card for sampling By using the internal
19. here Testing is another consideration that should not be overlooked and will be thoroughly carried out over the project This project will be tested in three phases as follows First phase testing the individual equipment This involves testing the functionality of all of the devices and integrating this with LabVIEW The separate VI developed for each piece of equipment will be tested by the team to ensure the information is reported accurately and the software is performing correctly The team member performing the test will fill out a standard form for each test they run This form can be found in the appendix This form will include their name the date and time performed Also the form will note the test performed and its results Ifa problem occurred it will be noted along with the problem description and a solution field for noting the fix to the problem This standard form for testing will help ensure proper testing as well as good documentation for later use In order to move on to the next phase of testing all device measurements must be reported accurately and any additional software functions are performing correctly The team will review the testing data from this phase with the faculty advisor and then the final decision to move onto the second phase of testing will be made Second phase testing overall system This involves testing the real time data transfer from all devices at once Also it involves testing the data collection an
20. irecin ot Getecton Cres Territory Research Technology Setection Technology impimenteton End Product Design Design fequeemerer Lera Procese Design Does End Ps odia Prototype wpibensent stion era of Prototype Letters Sutetttons Irptervectation of Prototype fret Product ted Product Testing Test Pra Test Developer Test Execution Test Dvatuation Testing Docunenteti rd f oct Document ation Dwrewingetant of End Liser Dos rr pad er Developnert of Martenanot Support Documentation Eod Product Desomoti ation Demonstration Parrrg Facdty Adma Demonctration Chert Demonstration mastna Reve w Pawi lers este ater Budd o TT d H m jm Hawa Haw wa i Prec moatiat zc hod Brema Progress ee The 206 poeti rr rrr Figure 19 Original Project Schedule 24 ho t3nlcfi Co i i i e A In i 5 o 01 F4 EI 3 1 Beiverabies Figure 20 Revised Project Schedule 25 Deliver dheo Proyect Plan Due Bond Proect Pan Oue End Product Dega Report Our usd End Iy ward Deens Papert Cum Poster Dun Fra Recon Due Bound Ping Report Due 7 3 5 z zl 7 5 Project oject ba Ga tat NENNEN 9 rod gt Dar The 2405 Figure 21 Deliverable Schedule 26 6 Project Team Information The following section will detail the contact information for every person that is involved in this project 6 1 6 2 6 3 Client Information Stephanie Lo
21. itioning carrier Figure 8 NI SCC IC20 for interaction with the PC and LabVIEW The signal Current Input Module conditioning carrier will be discussed in the next section Section 3 3 13 3 3 ESeries or Basic Multifunction WC SCC CI20 DAQ Device Source 4 e vervoltage Protection R3 dum me 3 Overvoltage ude A Protection 2 10M gt AISENSE gt AIGND 2 a Overvoltage d Protection y R2 2 E j S CHIX 8 1 Overvoltage ak PS E Protection 10M TE Signal source may be floating or ground referenc ed Figure 10 Omega FMA 5610 Connector Diagram left NI SCC IC20 Current Input Module Wiring Block Diagram right The NI SCC IC20 current input module will be purchased from National Instruments at an approximate cost of 130 50 Signal Conditioning Carrier In order to use the signal conditioning modules for the design an SCC carrier must be purchased to house these modules The SCC carrier selected was the SC 2345 which would allow direct cabling to the M Series DAQ board selected Section 3 5 The SCC carrier selected in shown in Figure 11 The SCC carrier comes at a price of 220 50 and will be purchased from National Instruments Figure 11 SCC carrier SC 2345 14 3 4 This unit will provide a low cost low profile housing for each of the SCC modules purchased The SCC carrier will be powered by the DAQ board with a 5V signal The modules will be connected
22. l insure that any changes made did not affect the overall system The team will evaluate the final surveys and upon final consultation with the client will decide if the final phase of testing is complete Project Continuation The project is on schedule as was planned in the project plan Thus it is the recommendation of the team to continue the project as proposed Detailed Design This section covers all the specific details of the team s design It includes all hardware wiring diagrams part numbers estimated part costs and part sources sellers that are required for each component The automated collection system consists of three main pieces of equipment in which data is collected from each being acquired with LabVIEW for the final product This section is divided into the five main components of this project These five main components are listed below The system flow diagram further relates these components in Figure 5 Oxygen concentration meter Mass gas flow meter Signal conditioning carrier Stirrer motor control DAQ board Software interfacing GUI 11 Digital Out RS 232 Interface Current 4 20mA Data Acquisition Board Retum 6 Channels areni Analog 0 5V LabView Figure 5 The basic flow diagram of the system 3 1 Oxygen Concentration Meter The selected oxygen concentration meter is the Thermo Electron Orion 3 Star benchtop dissolved oxygen meter This meter offers many features including measuring
23. ll be dynamic enough to display the appropriate information to the user as well as store the information to a file for later analysis When completed the entire system should allow end users complete access to data collection from all laboratory equipment This will ensure a deeper more complete understanding of the fermentation process and will culture a better environment for learning 6 5 References 1 Loveland Stephanie Power Requirements and oxygen mass transfer in an aerated agitated solution 2 EE CprE 491 Senior Design Course Notes By Dr John Lamont EE CprE 491 Senior Design Coursepack Supplement By Dr John Lamont 4 National Instruments LabVIEW 2004 lt http www ni com labview gt W 28 Test Performed Problems Yes I No Problem Description Figure 22 Team Standard Test Documentation 29 Ease of Use E Ai Comments Functionality E Comments Presentation Sa Comments Data Usability S A Figure 23 Intended User Survey 30
24. nd practical advice the team would like to acknowledge the effort of Dr Degang Chen of Iowa State University This group would also like to recognize Stephanie Loveland of the Iowa State University Department of Chemical and Biological Engineering She will provide finances design specifications and requirements for this project Problem Statement The problem statement is broken up into two separate sections one that defines the general problem area and another that describes the proposed approach to the solution 1 3 1 Problem Statement A mock fermentation vessel is available for use by senior chemical engineering students to conduct experiments in their final laboratory course This vessel currently uses archaic methods to operate the equipment and to collect data The objective of this project is to design update and install new equipment and software for the mock fermentation vessel apparatus to become automated and computer controlled A new oxygen flow meter will be needed for the apparatus specifically one that is able to communicate with the LabVIEW software The remaining equipment motor control and mass gas flow meter must be adapted so that they too can communicate with the LabVIEW software 1 3 2 Software must also be developed to gather data from the equipment and allow for smooth efficient operation by the user The software must be designed to take readings from the equipment and place the readings into certain functi
25. ng use and oxygen concentration meters 2 4 1 2 4 2 Data Acquisition Board Technology considered A means for collecting the information from the equipment will be done via a data acquisition board but there is a large variety of boards available There were several types of boards considered along with their unique attributes A USB DAQ unit would give the system easy connection to the computer that will be used for experiments and be relatively inexpensive to implement A drawback to this unit is there is no way to apply any signal conditioning with this type of unit The second type of DAQ considered for this project was a PXI DAQ system The PXI system allows for signal conditioning at a very high resolution signal and very high sampling rate but these great features are translated into the high cost of the this system The final DAQ consideration was the PCI board this board allows for signal conditioning and sampling at lower cost The PCI DAQ board does not provide extremely high resolution or sampling rate Technology selected After careful consideration of the equipment and our requirements the PCI DAQ board was selected The PCI DAQ board will allow for a sampling rate that is well within the constraints outlined by the client and will provide the advantage of signal conditioning capability Another benefit was the moderate cost of the PCI DAQ board while cost was not a constraint having an overly excessive sampling rate is
26. o follow when learning the software is being explored by the team Mich E t paia sel Road are y SCS se H i E 2 Figure 3 Prototype GUI 1 4 Operating Environment All equipment will be housed in the teaching laboratory of Sweeney 2059 This room is subject to a temperature controlled environment of 60 80 degrees Fahrenheit High levels of moisture could cause hardware failures which could render the data collection or software inoperable Also the connections need to be checked and cleansed from time to time due to normal dust accumulation and regular use 1 5 Intended User s and Intended Use s This section is divided into two parts one to cover the intended user s and the second is to cover the intended use s 1 5 1 Intended User s The mock fermentation vessel is a setup to be used by senior level students in the Department of Chemical and Biological Engineering as well as faculty within the department The users must have knowledge of safety procedures and requirements while conducting experiments within the lab Students will need to have been exposed to the concepts that the lab is designed to simulate 1 5 2 Intended Use s The intended use of this project is to automate the collection of data from the mock fermentation vessel apparatus This automation process will yield data in a real time display as well as saved file format for further data analysis by the users The end system is not intended to
27. onment intended users and uses limitations and assumptions expected end product and other deliverables 1 1 Executive Summary A mock fermentation vessel is available for use by senior chemical engineering students to conduct experiments in their final laboratory course This vessel experiment currently uses archaic methods to operate the equipment and to collect data Figure 1 shows the current configuration of the mock fermentation vessel and its equipment ZmMOORATI Figure 1 Mock Fermentation Vessel Apparatus The objective of this project is to design an automated system to collect the necessary data for the user This system will involve the use of data acguisition cards to interface with the current lab equipment and LabVIEW software will be used to collect the data Figure 2 illustrates the flow of the system components in the proposed project 1 2 1 3 Computer RS 232 Interface Data Acquisition Board Data Acquisition Data Collection and Software Interaction Figure 2 Control flow of System Interaction A user interface will be created that is simple enough for most users to operate and will be dynamic enough to display the appropriate information to the user as well as store the information to a file for later analysis Extensive documentation will also be included with the user interface to insure easy use in the future Acknowledgement For his aid in this project with technical a
28. ons within the program giving the user control over the use of the input data A user interface needs be developed so that the students can do several different functions with the information streaming in from the lab metering equipment A manual or tutorial should be developed alongside the user interface to provide the user some aide in using the software Problem Solution With the need of a new oxygen concentration meter for this project apparatus the team will work with the client in determining the best meter to purchase This will involve checking for easy connection and support by LabVIEW as well as meeting the client s needs The team will also determine the necessary collection equipment needed to collect data from the current laboratory equipment This will involve researching current methods of output from the equipment by contacting the equipment manufacturers This will allow the team to purchase the necessary data acquisition cards and signal conditioning units to collect accurate data from the equipment Data acquisition information from the equipment will then be interpreted by software developed using LabVIEW A GUI will then be developed to support real time interaction with the user An example of such a GUI developed using LabVIEW is shown in Figure 3 An extensive manual will be developed alongside this software to provide the user aide in using the software Also research into a possible flash interactive tutorial for the user t
29. ously to the PC This information will be in a comma delimited output which will be filtered using LabVIEW to grab the appropriate information for data storage and display Mass Gas Flow Meter The current mass gas flow meter of the mock fermentation vessel is the Omega FMA 5610 shown in Figure 8 This meter offers an output signal in the form of a 4 to 20mA analog signal This signal represents the mass gas flow in standard liters per minute and represents a scale of 0 to 10 SLM Therefore the scaling follows that 4mA corresponds to 0 0 SLM and 20mA corresponds 10 0 SLM and follows a linear scale between each of these points This output signal is obtained from the 9 pin D connector on side of the enclosure The connector will output the current on pins 8 and 9 These pins will be wired using standard copper wire to the current Figure 9 Omega module selected from National Instruments for signal FMA 5000 Series conditioning This module is the NI SCC IC20 current input module This module is shown in Figure 9 This module uses precision resistors to convert the 0 to 20mA current into a 0 to 5V signal The current will be wired in a differential configuration to ensure accurate measurement from the module Figure 10 below shows the pin configuration of the D connector on the Omega FMA 5610 on the left and shows the wiring block diagram used for connecting to the SCC IC20 on the right This SCC IC20 module will be plugged in the signal cond
30. ration for signal conditioning is the extra purchase of a signal conditioning carrier which would house potential signal conditioning modules This signal conditioning carrier offers a low cost signal conditioning solution for a wide range of analog or digital input and output signals Without purchasing this SCC carrier the overall cost would be decreased but the signal conditioning modules would be unable to be used Technology Selected The signal conditioning carrier was selected as the proper means for facilitating signal conditioning It would the use of the signal conditioning modules and its additional cost was outweighed by simplification of the design and the future upgradeability of the system For the stirrer motor control as all the analog voltage input modules from National Instruments have a working isolation up to 300V this covers the issue with the floating ground Also since transients may be present utilizing the differential capability of these modules shields against this danger In evaluating each of the modules for a necessary voltage range needed the 0 to 5V input range two channel analog input voltage module from National Instruments was selected For the mass gas flow meter the output current signal was decided to be scaled to the 0 to 5V signal This would simply the overall design as a similar module would be used as in the stirrer motor control Also this would make the importing of data into LabVIEW very similar
31. rototype Implementation Integrate the VI s developed in the design process into a main GUI system Task 5 End Product Testing Test the product to check that it meets all operational and user defined requirements Task 6 End Product Documentation Document all the details of the product design and develop an end user manual and maintenance documentation Task 7 End Product Demonstration Demonstrate the functionality of the product to the client advisor and industrial review panel Task 8 Project Reporting Document the details of the whole project in a final report 19 4 2 Personal Effort The tables below show the original and revised allocations of hours for personal effort Table 1 ene resuma Effort Andrew Arndt Adam Daters Brad DeSerano Austin Striegel Totals 16 Andrew Arndt 3 Adam Daters Brad DeSerano Austin Striegel Totals 4 3 Task 1 Problem Definition Task 2 Technology Considerations and Selection Task 3 End Product Design Task 4 End Product Prototype Implementation Task 5 End Product Testing Task 6 End Product Documentation Task 7 End Product Demonstration Task 8 Task Reporting The changes made in the distribution of hours reflect greater insight into the commitment required for each task The only increase in time allocation occurred in the end product testing task this results from the need to thoroughly test and debug the software
32. t be worn at all times when working in 2059 Sweeney No more than 4 significant digits stored upon measurement The voltage signals from the stirrer motor control must be electrically isolated The oxygen concentration meter must read from 0 to 9 5 PPM dissolved oxygen The oxygen concentration meter must be a benchtop unit 1 7 Expected End Product and other Deliverables The expected end product of this project is an automated collection system for the mock fermentation vessel apparatus This system will include all the necessary hardware for collection and data acquisition A GUI shall be developed that displays real time information to the user and can save this data into an Excel file format Along with the automated collection system this project will produce two written documents a design document and an end user operating manual At the end of the project there will be a final report encompassing the entire project The end user operation manual shall provide instruction on the operation of the software and documentation information It shall be written in a non technical manner It shall be delivered at the completion of the project The final report shall include all the details about the project description as well as outline how the system operates 2 Design Approach This section outlines the approach formulated by the team to ensure that the system will be correct 2 1 2 2 Design Objectives The information that the
33. this page E fi This first page will prompt nins users for initialization information needed later for documentation and to run the xpetimeni Paramelet experiment The page vvill RR enable users to specify run E time identify group to members the date and the time the experiment was performed Additional input ho l poed LL Figure 17 Initialization Screen 17 will be considered and added by the team if 1t is deemed necessary At the bottom of the page a button with the word Start appears By clicking on this button users will continue with the experiment and will display the second screen As seen earlier in the executive summary Section 1 1 screen two will hold four real time displays for the four main sources of data from the experiment torque speed oxygen concentration and mass gas flow Each display will keep track of the data in real time which means that the users will be able to see the graphs update dynamically as the experiment progresses Figure 18 shows a zoomed in look at one of the dynamic graph displays that will be implemented The toggle switch at the top left of the screen enables users to start and stop the experiment on demand This means that data will not be recorded when the experiment is turned off Other features of the page include a kill switch to totally stop experiment if a problem is noted and a button to allow users to examine the data in an Excel spreadsheet as th
34. tirr r Motor Control e o S dr ors 15 3 5 Data Acquisition Board tuis sis eende aree citet itat eia at e ATA ERA EG RA GE EAR AR HUS Reg ge GARDE 16 36 Software Interlaer se Se se ee dtu tome Se mat Diete indere ies e eius 17 4 ROS QUE COS Es MR E T UT 18 41 Task Definiti ns qua dere E e toate VORNE Cta d 18 4 1 1 Task 1 Problem Definitioti urere tato dar e ena reet shte 18 4 1 2 Task 2 Technology Considerations and Selection sss 19 4 1 3 Task 3 End Produet Design uud Ga nit SEE ER Re 19 4 1 4 Task 4 End Product Prototype Implementation esee 19 4 1 5 Task 5 End Product Testing cs sta 19 4 1 6 Task 6 End Product Documentation ococonoccnonoconnnoonnoonncnonoconanonnnconoconn nono RA ee 19 4 1 7 Task 7 End Product Demonstration coonoccnonocoonnononoonncnonoconnnonncconcconnnnancconccnnos 19 ALS Task 8 Project Reporting eoo taa 19 2 2 Personal E HOtb cuc code ace ESCUELA D edu T LU CIUS cae ad ER 20 4 3 Other Resource Requirements eee deren eere dede ert e deci rb n daa 20 Ad Financial Requirements is eec o e pe tva lag ee ato dt 21 5 O 23 6 Project Team Informafioli us scoop ee uevor cerdo prese eo eee Yin uv so ve 27 Ola Chent Toto qt OTI ecco estet eese oet oe eee ett ose ase Ne e da rase Be E SM DR 27 6 2 Faculty Advisor Information Re Ge ee Ge ee ee 27 6 3 Team Member deett te ete itr E EE A AEE du EES e eva EE 27 64 Closing SUMM
35. to the data of stirrer motor control Oxygen Concentration Meter Technology considered As the current oxygen concentration meter used in the mock fermentation vessel is out of date and does not provide an interface with a PC a replacement must be identified There are a wide variety of oxygen concentration meters available on the market but as the client specified that it must be a benchtop meter this narrowed the field Two oxygen concentration meters were identified that met the required specifications but had a few differences Omega Engineering carried a benchtop oxygen concentration meter which had an RS232 link for computer connection and provided 100 data point logging This unit offered little support for future supplies and was to be no longer carried by the manufacturer The other unit identified was the Orion 3 Star benchtop oxygen concentration meter from Thermo Electron This unit offered an RS232 link for computer connection and provided 200 data point logging This unit also offered a 3 year replacement warranty and up to five years of guaranteed manufacturer supply support Technology selected The Orion 3 Star oxygen concentration meter was selected from Thermo Electron This unit offered all the functionality that was desired by the client while also offering attractive features and support for an extended period of time 2 5 Testing Approach The methods for testing and the criteria for acceptance will be discussed
36. veland ISU Department of Chemical and Biological Engineering Office 2033 Sweeney Hall Office Phone 515 294 3024 Email prairie iastate edu Faculty Advisor Information Dr Degang Chen Office 329 Durham Office Phone 515 294 6277 Email djchen iastate edu Team Members Andrew Arndt Major Electrical Engineering Address 209 N Hyland 5 Ames IA 50010 Phone 515 450 8650 Email abarndt iastate edu Adam Daters Major Electrical Engineering Address 123 Sheldon Ave 11 Ames IA 50010 Phone 641 485 5286 Email adaters iastate edu Bradley DeSerano Major Electrical Engineering Address 119 Stanton Ave 710 Ames IA 50014 Phone 319 610 3901 Email bdez iastate edu Austin Striegel Major Electrical Engineering Address 125 Campus Ave 4 Ames IA 50014 Phone 712 830 0470 Email astrieg iastate edu 27 6 4 Closing Summary A mock fermentation vessel is available for use by senior chemical engineering students to conduct experiments in their final laboratory course This vessel currently uses archaic methods to operate the equipment and to collect data The objective of this project is to design an automated system to collect the necessary data for the user This system will involve the use of a data acquisition card to interface with the current lab equipment and LabVIEW software will be used to collect the data A user interface will be created that is simple enough for most users to operate and wi
Download Pdf Manuals
Related Search