Home

Pergola-Install

1. Some structures may require two or more people to install safely Check for underground utilities before digging or driving stakes into the ground General Information Wood components are manufactured with Cedar C Lanceolata which is protected with factory applied water based stain Knots small checks cracks and weathering are naturally occurring and do not affect the strength of the product Annual application of a water based water repellent sealant or stain will help reduce weathering and checks Tools Required e Tape Measure e 2 Phillips or Robertson Adjustable Wrench e Safety Glasses Carpenters Level ells ol ocrewanver e 1 8 Drill Bit e Adult Helpers Ratchet with extension Carpenters Square 7 16 sockets Pencil e ir a or Cordless Open End Wrench e 3 16 Hex Key 7 16 e 8 Step Ladder Keys To Assemble Success This identifies information that requires special Check that set or assembly is properly level attention Improper assembly could lead to an before proceeding unsafe or dangerous condition Din Where this is shown 2 or 3 Pre drill 1 8 8 3 16 Bit people are required to safely Pre drill a pilot hole complete the step To avoid E 3 before fastening screw injury or damage to the 8 AG or lag to prevent assembly make sure to get help splitting of wood Tighten Bolts Measure Check that assembly is square Square Distance i i Assembly This indicates time to tighten bolts
2. but 2 U usc not too tight Do not crush the wood Se eee This may create splinters and cause proper location structural damage MATERIAL LIST 1 1 2 x 5 1 2 4 2 x 6 x 132 1 1 2 x 2 1 2 5 8 x 5 1 2 4 2x6x37 4 2 x 6 x 8175 2 1 x 6 x 80 F 4 2 x 6 x 21 4 2 x 6 x 80 22 2x 3x 34 11 2x 3x 83 8 8 x TZ 4 17 dr rt 1 4 4 EA 3 0 4 4 A 1A MN MATERIAL LIST LR EE OO NN 16 Top and Bottom Rail 8 One High X ET X 12 4x4 Post En 10 x 1 1 2 Pan Head Screw 12 Post Top Connector With 7 16 Hex Bolt Assembly 48 Panel Clips 8 Three High X Panel STEP 1 ASSEMBLE PANELS 1 Remove the upper metal connectors on both sides of PX3 Three High X Panel Reattach the metal connectors to PX3 by securing the bottom two holes of the metal connectors to the top two holes on PX3 so that the metal connectors stick out from the top Slide PX1 One High X Topper between the two protruding metal connectors on the top of PX3 Attach the metal connectors to the factory drilled holes in PX1 Fig 1A Ensure Panels are oreinted correctly Fig 1B 2 Secure panels with a S4 2 1 4 Wood Screw the location indicated by the large P 4 arrow in the direction of the arrow 3 Secure R Top and Bottom Rails to Panel Asse
3. C Beams as shown in diagram Attach with 2 Hex Bolts per post 4X Le 2X6 X80 1 2 BEAMS 4X 2 X 6 X 36 13 16 BEAMS 7 STEP 7 INSTALLING PERGOLA ROOF Wa fer Bolt Assembl y 1 N OO Layout the roof on the beams Allow for a 10 1 4 or 26cm Fasten roof to beams with Assemble roof by fastening H 2 x 3 x 34 3 5 Trellis Ends to l 2 x 3 x 83 1 2 Trellis Middle using 2x3 Metal Bracket and WL Wafer bolts as shown in Fig 1 as shown in figure 2 gap between each trellis assembly and 4 1 4 or 11cm gap between the outside trellis assemblies and the outside beam side Fig 3 S3 8 x 1 2 Wood Screw at pre drilled hole on trellis end and 51 10 x 1 Pan Screw on 2x3 Metal Bracket 22x 2 X 3 X 34 3 4 TRELLIS END 22x 948 3 1 2 WOOD SCREWS DX MAR WAFER BOLT ASSEMBLY 11X 7 2 X 3 X 83 1 2 TRELLIS MIDDLE 44x Gi 10 X 1 SCREW 22X 2X3 BRACKET
4. INSTALLATION MANUAL 12X12 COMPLETE PERGOLA ROOM BA 3 15 4 2 4 lt OUTDOOR LIVING 6 61 2 11 1 2 Customer Support 1 888 784 0878 1 99m 3 37m info quality edge com Quality Edge 2712 Walkent Dr NW Walker MI 49544 www insideoutunderdeck com 1 99m HEIGHT 8 2 OR 2 49M a 1 2 gt 3 37m SAFETY NOTICE Components are intended for privacy decorative and ornamental use only Product is NOT INTENDED for the following A safety barrier to prevent unsupervised access to pools hot tubs spas or ponds Safety railings for elevated platforms or decks As load bearing support for a building structure heavy objects or swings Used in structures that trap wind rain or snow that would create extra load on the product Permanent structures may require a building permit As the purchaser and or installer of this product you are advised to consult local planning zoning and building inspection departments for guidance on applicable building codes and or zoning requirements Wood is NOT flame retardant and will burn Grills fire pits and chimneys are a fire hazard if placed too close to the structure Consult user s manual of the grill fire pit or chimney for safe distances from combustible materials During installation follow all safety warnings provided with your tools and use OHSA approved safety glasses
5. REW STEP 3 ATTACH PANELS TO POSTS ti 8 1 Place panel assemblies on posts as shown Fig 1 allowing a 4 gap between the bottom of the post and the bottom edge of the bottom rail on the panel assembly Assemble with the help of another adult 2 With a 1 8 drill bit predrill holes as shown in figure 2 3 Fasten the panel assembles to the post and Panel Clips with a 55 1 Pan Head Screw provided in location of arrows Fig 1 4 Repeat until all four pergola bases are assembled Fig 1 Front View Side View XxX Fig 2 Predrill Holes and Fasten with S5 1 Pan Head Screw 4 10 2cm 48X 1 PAN HEAD SCREW T STEP 4 LAYOUT POSTS AND a ti CONNECTORS 1 Layout pergola bases in configuration shown in figure 1 Posts must be securely installed to support structure Consult local building codes and ground conditions for required footing design It is recommended the structure be secured to existing stone concrete or deck with the 4 x 4 Post Base or equivalent hardware 2 Install Post Top Connectors with S6 1 1 2 Pan Head Screws provided Fig 2 Ensure the direction of the Post Top Connector is the same direction as indicated by the arrows in figure 1 Fig 2 Attach Post Top Connectors with S6 1 1 2 Pan Head Screws 6 6 1 2 gt 199 4cm Fig 1 Install on a flat and level surface 6 6 1 2 14 9 7 8 1 99 4
6. cm 451 8cm 10 5 1 2 Yo 318 8cm 48 ss 1 1 2 PAN HEAD SCREWS 12 POST TOP CONNECTOR GF STEP 5 ASSEMBLE EXTENDED BEAM NO 1 Assemble 2 DDE Extended Beam by securing two D 2 x 6 x 81 7 8 Beams and E 1 D NS x 6 x 80 1 2 Board with WT Wafer Bolt assembly and S2 8 x1 1 2 Wood Screws N as shown Note Wafer Bolt assembly in diagram below Wafer Bolt Assembly 20X wr 1 4 X 2 WAFER BOLT ASSEMBLY W T NUT 4X 2X 6X 81 1 2 BEAM 8 2 8 1 1 2 WOOD SCREW 2X 1 X 6 X 80 1 2 BOARD GK STEP GA MOUNTING BEAMS TO CONNECTORS 1 Attach C to DDE with 3 S3 8 X 3 1 2 Wood Screws 2 Attach C to post with 3 WH Hex Bolts Connect the other side to DDE with 3 S3 X 3 1 2 Wood Screws 3 Attach A to post with 2 WH Hex Bolts Attach F to Post with 2 WH Hex Bolts and the other side to DDE with 2 S3 8 X 3 1 2 Wood Screws 4 Repeat assembly for both beams 4x A 2X 6 x 13 1 2 BEAM END 12x 3 8 3 1 2 WOOD SCREW 4X 2X6X37 BEAM 56X wH HEX BOLT W NUT 4X F 2X6 X21 5 8 BEAM GF STEP 6B MOUNTING BEAMS TO CONNECTORS Fd 1 1 Connect both DDE panels with 2 G 2X 6 X 80 1 2 Beams with Hex bolts provided 2 per post joint 2 Attach remaining 2 G 2 X 6 X 80 1 2 Beams between outside posts as shown in diagram Secure with Hex bolts provided 2 per post 3 Place 4 2 X 36 13 16 Beams between A amp F and attach to
7. mbly with S4 2 1 4 Wood ocrews locations indicated by arrows in the direction of the arrow R Top and Bottom Rails will overhang 1 4 on either side of panel 4 Repeat until eight panel assemblies are created p p R of Geo Fig 1B Filler Strips on Bottom of Panel A 3E NC 3 Fig 1A 8X pa ONE HIGH X TOPPER 32x 4 8 2 1 4 WOOD SCREWS 8x THREE HIGH X PANEL 16 amp BOTTOM RAIL STEP 2 ATTACH PANEL CLIPS TO POSTS amp 54 Fig 1 Front View Fig Side View 1 On a flat surface place P 4x4 Post on its side and position Panel Clips in locations indicated in Figures 1 and 1A Ensure Panel Clips are oriented as shown in Diagrams A 2 Panel Clips should be placed in the centre of the post or the leading edge of the clip should be 1 3 8 or 3 5cm away from the side of the post as shown in Fig 2 3 With Panel Clips in place mark screw holes with a pencil and pre drill holes with a 1 8 drill bit Not provided 4 Secure Panel Clips in locations indicated in figure 1 and 1A with S7 8 x 1 1 2 wood screws 5 Repeat for each post configuration 4 in total 75 190 5cm Fig 2 40 101 6cm Pre drill holes and secure with S7 8 x 4 1 1 2 Wood Screws 10 25 3cm E Top View 12x 2 4x4 POST 48X PANEL CLIPS 48x 48 X 1 1 2 WOOD SC

Pergola-Install

Contents

Download Pdf Manuals

Related Search

Related Contents