User Manual
Contents
1. 3 52 89 5 Figure 2 6 2 2 Recessed Mounting Step 1 Drill mounting hole Stick the schematic label on the ceiling and drill a hole with 180mm in diameter as per the label a S Figure 2 7 Step 2 Install adapter Pre loosen M4 screws to make the blocks away from snap joints place the adapter through the hole screw the M4 screws to let the blocks to fasten the ceiling Figure 2 8 Step 3 Install camera module Loosen the 3 Torx T20 screws with an L Shaped Torx wrench T20 and take off the bubble Install the camera module to the adapter with 3 M4X6 pan head screws gt 3 M4X6 pan head screws Figure 2 9 Step 4 Adjust camera angle Adjust the panning angle according to your surveillance direction Loosen Screw A to adjust tilting angle then fasten the screw Adjust the rotating angle to ensure upright video Adjust the rods in the lens to focus clear Tilting 75 75 Figure 2 10 Figure 2 11 Step 5 Install dome bubble Install the bubble flange to camera module Align the screw holes of the two parts and fasten the 3 Torx T20 screws with the L Shaped Torx wrench T20 Step 6 Install recessed mounting housing Align the 3 grooves of the housing with the 3 bolts in the adapter and lock them toget2. 352x288 352x240 and closed For MJPEG stream the resolution comes to 1280x720 720x480 and closed Frame Rate the number of compressed frames produced by camera per second The bigger the frame is the better the image continuity will be but the CPU performance is lowered The smaller the frame is the worse the image continuity will be but the CPU could handle more events The maximum frame rate for H 264 is 30fps The maximum frame rate for MJPEG is 10fps Note the video settings of H 264 major minor stream are linkage with that of MJPEG stream If H 264 major stream is set to 720P 30fps minor stream closed MJPEG is only able to set to 720P 4fps If H 264 major stream is set to 720P 25fps minor stream closed MJPEG frame is able to set to 10fps Do operate according to the prompt on the page GOV number GOV number means the ratio of I frame to P frame in compressed video images The bigger the value is the less the data quantity is and the less network resource it occupies Max GOV number can be set to 60 Bit Rate There are 2 modes of bit rate variable rate vbr and constant rate cbr The variable rate can adjust the bandwidth that it occupies automatically according to the complexity of image because the complexity of real video sequence keeps changing details speed etc and the variable rate setting mode can be used to choose how much bandwidth should be used If the video gets more details and
3. Information DLR LEASE 12 28 03 View frum Typa Lc visum E Vi ar see Fs Pis cde fie z m w em Funcion buttons amp Figure 3 4 A Note If InfiPlayerAX control installation falls the live video won t display Then you should change the IE security level 1 Click Tool in the menu bar and then select Internet Options from the drop down menu 2 Select Security in the pop up Internet options as shown in the following figure 3 Click Internet icon then click Custom Level to pop up the following interface 4 Select Enable or Prompt in the options of Download unsigned ActiveX controls 5 Select Privacy in the Internet options and uncheck the checkbox of Block pop ups Refresh the webpage and set up the ActiveX control as per the prompts and then live view interface appears normally By now the preparation for image viewing with IE browser comes to an end CHAPTER IV BASIC FUNCTION OPERATION This chapter mainly introduces the settings and operation of V6812 T00 series 4 1 Live View Start IE browser after the server is powered on for about 75 seconds and then enter IP address such as http 192 168 1 100 default in the address field Note The default subnet mask is 255 255 255 0 and the default gateway IP address is 192 168 1 254 For normal access please correctly set local IP parameters before system login The login interface is dis
4. 0 360 Y Tilting 75 75 Adjustment Z Rotating 0 360 Day Night i ICR Functionality TP Color mode 0 5 lux F1 4 30IRE AGC ON Sensitivity B W mode 0 1 lux F1 4 30IRE AGC ON Scene Mode Manual mode Shutter priority mode Shutter Auto Manual 1 25s 1 8000s Auto Manual Incandescent light Cool white fluorescent White Balance light Sun light Cloudy Natrium light Gain Control Auto Manual Video Compression H 264 High profile M JPEG Maximum Resolution 1280x720 H 264 M JPEG Major stream 1280x720 1024x768 800x600 Optional Resolution Minor stream 720x576 720x480 640x480 352x288 352x240 Maximum Frame 308 1280x720 Rate ps Variable bit rate Data Rate Constant bit rate 256Kbps 10000Kbps Audio Compression G 711 u Audio 1 input Linear level Resistance 1000 Ohm 1 output Linear level Resistance 600 Ohm 1 RJ45 10 100M self adaptive Ethernet port IPv4 IPv6 TCP UDP IGMP DHCP FTP SNMP V3 SMTP NTP RTP RTSP RTCP HTTP HTTPS TSL SSL 802 1X QoS PPPoE DNS ARP ICMP UPNP DDNS Profile S 1 alarm input 1 relay output Power Supply PoE IEEE 802 3af Class 2 Power Consumption Operating 14 F 122 F 10 C 50 C Temperature Storage Temperature 4 F 140 F 20 C 60 C Operating Humidity 0 90 RH non condensing Unit Dimensions A Hx 3 88 x5 31 98 5mm 135mm Box Dimensions ji LxWxH 8 03 x7 48 x7 13 204 mmx190
5. If user selects mail in Alarm Settings interface system will send mails according to SMTP settings 4 3 4 HTTPS Settings Network FTP SMTP HTTPS 802 1X QOS CA certificate import CA certificate Browse Submit Figure 4 13 HTTPS Settings V6812 T00 series camera supports HTTPS protocol You can import the CA certificate in the interface 4 3 5 802 1X Settings Network FTP HTTPS 802 1X Qos 802 1X Authentication EAP method User name Password Save Cancel Figure 4 14 802 1X Settings V6812 TOO series camera supports 802 1X protocol You have to enable 802 1X authentication when needed Then select an EAP method and enter the user name and password 4 3 6 QOS Settings Network FTP SMTP HTTPS 802 1X Qos Qos QOS option Normal service vj Max reliability Max throughput Min delay Cancel Figure 4 15 QOS Settings There are 4 network Qos modes to be selected 1 Normal Service 2 Max Reliability 3 Max Throughput 4 Min Delay Recommend Normal Service 4 3 7 IGMP Settings Network FTP HTTPS 802 1X QOS IGMP Stream type Major Stream v State On O off MultiCast IP address 224 0 1 88 RTP port 8888 Save Cancel Figure 4 16 IGMP Settings V6812 T00 series camera supports multicast function In the IGMP interface users can select the stream type and set the state multicast IP address and RTP port 4 3 8 SIP Settings Network FIP HI TPS 807
6. and IO input 1 In Auto mode the camera can automatically control the day night switching in Day mode videos are in color mode in Night mode videos are in black white mode in IO input 1 mode ICR is controlled by external signals AE target set AE target level It can adjust video brightness via AE target setup 4 4 3 Effect Settings In the Effect Settings interface users can adjust the brightness sharpness hue contrast saturation and 3D denoise in two ways General or Mode as shown in the figure below General Brightness n Sharpness Hue Contrast Saturation PREEE amp hHRBB B B 5 3D denoise Figure 4 10 Effect Set General Drag the sliding block to adjust the brightness sharpness hue contrast saturation and 3D denoise O General 9 Mode Mode call Mode edit Start time End time Call Mode mode Name mode1 mode ICR control Auto mode model M Scene Normal model Sharpness 128 Hue 128 Contrast 128 Saturation g 64 3D denoise la 16 mode1 v 0 0 o model w Brightness d 128 Ir 0 0 mode e Factoryset Save Cancel Figure 4 25 Effect Set Mode The camera supports 6 video effect modes Users can set and save Name ICR control mode and Scene parameters for each mode Click Factoryset to restore it to default setting
7. and save the heartbeat sever IP address and Heartbeat interval and then the heartbeat package will be sent to the server or client which greatly facilitates the server or client to know about the camera s network status 4 3 2 FTP Settings Network FTP HTTPS 802 1X QOS FTP Server IP User name Password Save Cancel Figure 4 11 FTP Settings V6812 TO0O0 series camera has the function of alarm associated with FTP upload alarm triggered image snapshot Configure server IP user name and password in the FTP settings and activate FTP handling way in alarm settings then alarm triggered images FTP upload can be achieved 4 3 3 SMTP Settings Network FTP SMTP HTTPS 802 1X QOS SMTP Server IP 0 0 0 0 From IPQinfinova com To Mseriestest infinova cc GE Authentication On off Save Cancel Figure 4 12 SMTP Settings User needs to set mail server recipient etc in SMTP settings interface e Server IP Set mail server address e From Set sender s mail address e To Mail address of recipient e CC Mail address of the person copy to e Authentication Enable or disable authentication function This function should be set according to authentication requirements of mail server e User name Sender s name it can be set according user s needs e Password Set sender s password Note there is no limit for Sender s name and password settings After setting click Set Save to take effect
8. IV Basic Function Operation 4 Browsing Videos 4 2 System 4 3 Network Settings 4 4 Camera Settings 4 5 Audio amp Video Settings 4 6 Alarm Settings 4 7 Record Management 4 8 Account Settings 4 9 System Log Appendix I Magnetic Ring Filter Instruction Appendix II Questions amp Solutions Appendix III Cable Diameter Calculation and Lightning amp Surge Protection CHAPTER SYSTEM INTRODUCTION 1 1 Product Description V6812 TO0O series IP minidome camera features 1 3 progressive scan CMOS sensor and built in megapixel HD lens with the focal length of 2 8 12mm With H 264 High profile M JPEG compression format utilized this camera can output HD full frame videos with the resolution up to 720P V6812 TO0O series IP minidome camera provides motion detection and privacy mask function which can protect certain private areas from being seen by operators In addition Power over Ethernet PoE greatly simplifies transmission cable Compact structure makes it easy to install Also this camera provides 3 axis adjustment easy to adjust the monitoring angle V6812 TOO series IP minidome camera is suitable for financial institutions telecommunications governments schools airports factories hotels museums city streets and other high resolution surveillance applications 1 2 Product Features Infinova s V6812 T00 series camera has the following features and functions 1 3 progressive scan CMOS sensor IR Cut
9. moving fast then it takes up more bandwidth to transmit and reversely it occupies less bandwidth When the setting goes with constant bit rate then the image is transmitted under a constant bandwidth Bit Rate Upper Limit You have to set the upper limit of bit rate if vbr is selected the stream size will be fixed if cbr is selected and the stream size is defined in the Bit Rate Upper Limit For major stream the bit rate upper limit can be 1000Kbps 10000Kbps for minor stream the bit rate upper limit can be 256Kbps 2000Kbps 4 5 2 OSD Video Privacy Motion Shelter Link config Path Row mode Model C Mode2 Text 1 On C Off X Y 0 99 fo fo Context 230330 Text 2 Fon Coff x y 0 99 fo fo Context 232323 Date OSD On C Off x Y 0 99 ss o Font size 5 v Figure 4 28 OSD Mode 1 OSD settings include Text OSD and Date OSD The camera supports two OSD modes Mode 1 Mode 2 You can switch the mode only if Text 2 1s on Only if Text 1 Text 2 and Date OSD are set to On you can set the text content and the display position of text and date Context Enter the text content in the box of Context which allows up to 40 characters lower upper case letters and 0 9 X axis amp Y axis The title axis location Both X axis and Y axis can be any of whole numbers from 0 to 99 Font Size Set the font size to be displayed The bigger the value is the larger the font size 1s Defau
10. password server IP and Port number After setting completed click Save button to take effect 4 3 10 DDNS Settings Server enable Server type Oray DDNS Address Domain User name Password Update time Minute 2 500 Cancel Figure 4 19 DDNS Settings Dynamic Domain Name System DDNS synchronizes the host name and dynamic IP address continuously Users don t have to memorize the dynamic IP address but enter the dynamic domain name to connect the IP camera DDNS needs a PC with fixed IP address on the Internet to run the dynamic domain name server Operation select DDNS type in Enable option enter the IP address of the DDNS server into the address bar configure domain name user name password and update time and then save the settings Open the IE browser and enter the domain name to go to the query page of the device 4 3 11 UPnP Settings Create mapping between private network and the Internet via UPNP protocol Select UpnP option and enter the configuration page The added mapping list appears on the page Addo Loralie Service Protocol Internal port External port UOperate a WwebSerice TCP E 30 x m PrvGerwce TEP 5 aa n El RTSFService I 554 xx Figure 4 20 UPnP Settings means to edit user In Operation column means to delete information Click Add button to add the mapping Protocol Internal part External port Sava Figure 4 21 4 4 Camera
11. space and state of SD card and also format it To remove SD Card when it is being used please click Reject 4 7 2 Replay Settings Replay Figure 4 38 Replay Video Search set the start and end time and then click the search button All videos recorded during this period of time will display in the list Settings Replay Search E Dawna Figure 4 39 Searching Videos Replay to replay a video double click a file in the list with the mouse or select a file and then press the Play button E During playing click H or J to pause or stop playing Click the button on the right of video window the right window will disappear show as below Settings Replay Figure 4 40 Click the button the interface will return to the page as Figure 4 35 Download You can download the videos stored in the SD card to your PC Select the file from the video list also you can select multiple files simultaneously using the key Ctrl or Shift and then click the button Download to enter the downloading interface Download 2013 06 18 09 45 43 gt 2013 06 18 09 46 13 Waiting 2013 06 18 17 37 30 gt 2013 06 18 17 47 01 Waiting 2013 06 18 18 23 33 gt 2013 06 18 18 33 34 Waiting Figure 4 42 Downloading Videos Save to Set the path to save the downloaded files If resetting required click the button Browse AVI H 264 drop down list box select the downloaded
12. telecommunication around Meanwhile there is no guarantee that interference will not occur in a certain particular installation situation Read this manual carefully before installation This manual should be saved for future use Important Safety Instructions and Warnings Electronic devices must be kept away from water fire or high magnetic radiation Clean with a dry cloth Provide adequate ventilation Unplug the power supply when the device is not to be used for an extended period of time Only use components and parts recommended by manufacturer Position power source and related wires to assure to be kept away from ground and entrance Refer to qualified personnel for all service matters Save product packaging to ensure availability of proper shipping containers for future transportation A voltage harmful to humans Indicate that the un insulated components within the product may carry a Indicate operations that should be conducted in strict compliance with instructions and guidelines contained in this manual Warning To avoid risk of fire and electric shock keep the product away from rain and moisture CONTENTS Chapter I System Introduction 1 1 Product Description 1 2 Product Features 1 3 System Requirement 1 4 Product Model 1 5 Specifications 1 6 Precautions Chapter II Installation Instruction Chapter III IE Browser Settings 3 Equipment Connection 3 2 Software Installation Chapter
13. the blue frame changes into green which indicates a successful setting Besides you can set the area name and sensitivity To cancel a motion detection area just cancel the box ticking 4 5 5 Shelter Alarm gt v gt E 4 o Ie teem o o it se wd IV Enable Draw Name Sensitivity g c cf sk Most sensitive Save Cancel Figure 4 32 V6812 TO0O series camera supports shelter alarm function Users can easily set the shelter alarm areas with the mouse At first enable shelter alarm Click the button Draw with the mouse press the left mouse button and drag on the video till a blue frame displays on the screen Then click the button Save with the left mouse button and the blue frame changes into green which indicates a successful setting Besides you can set the area name and sensitivity It will trigger alarm when the video within the area is shielded Refer to Section 4 6 for alarm contact details 4 5 6 Link Configure 90 port 2 zy z B RTSP Note The three streams all use this configuration Figure 4 33 For each stream the total of 90 port and RTSP port is 5 In this interface you can set the video numbers of 90 port and RTSP port The default setting is visit 2 ch major stream 2 ch minor stream and 2 ch MJPEG video via 90 port and visit 3 ch major stream 3 ch minor stream and 3 ch MJPEG video via RTSP port 4 5 7 Storage Path You can set the photo saving path and re
14. the installation fails check whether there is video viewed through other IE window or page You should close the video or the IE window directly If it successes click refresh you can view the live video Method 2 The prompt message as below will come out in the page after a successful login Right click Add on Disabled and select Run Add on Infincsa Hetecrk Camera Wl aur curent security setting put your computer at nel Click here to change your tecurity settings E Add cn Disabled Run Add on Infinova HD Network Mi Securty Lettings at Risk Pun Add on an All Websites What s the Fisk Irfeematien Bar Help iren Vinur Burl mara Figure 3 2 Then the prompt of security warning will pop up to remind the user to install InfiPlayerAX control Click Install Internet Explorer Security Warning The publisher could not be verified Are you sure you want to install this software Mame InfiPlayerAX cab Publisher Unknown Publisher should only install software from publishers you trust How can I decide what Q This file does not have a valid digital signature that verifies its publisher You software to install Figure 3 3 After InfiPlayerAX control is installed you can view the live video If it pops up reboot prompt please cancel reboot Then close all the IE window and install InfiPlayerA X control once again The live video will display as below Infinova wo network Mini Dome Camera Live View
15. the tube should be connected to the lightning proof grounding device Additional high power lightning proof equipment and lightning rods should be installed for strong thunderstorm or high induced voltage areas such as high voltage substation The lightning protection and grounding for outdoor devices and wires should be designed in line with the actual protection requirement national standards and industrial standards The system should perform equipotential grounding by streaming shielding clamping and earthing The grounding device must meet anti interference and electric safety requirements There should be no short circuiting or hybrid junction between the device and the strong grid Make sure there s a reliable grounding system with grounding resistance below 4Q below 102 for high soil resistivity regions The cross sectional area of the earthing conductor should be no less than 25mm ye M CP Front device for surveillance system Mounting pole for front device Separated layout for the lightning rod and the standing pole Infinova 51 Stouts Lane Monmouth Junction NJ 08852 U S A Tel 1 888 685 2002 USA only 1 732 355 9100 Fax 1 732 355 9101 sales infinova com V1 4 1409
16. 1X SIP server SIP server IP Port Server ID Device ID Alarm 1D Register Interval 1800 Heat beat Interval 60 Auth UserName UserName Password Cancel Position Information Position name Longitude Latitude Cancel Figure 4 17 SIP Settings SIP Server to configure SIP server for device SIP Server IP the IP address of SIP server Port the port number of SIP server Server ID the ID of SIP server Device ID the device ID used for registration with SIP server Alarm ID the ID registered for device alarm Register Interval the interval for re registration of device in seconds Heat Beat Interval the interval to send heatbeat information by the device in seconds After configuration completed click Save and the device sends a registration request to the server Position Information the mounting information or instruction for device Longitude the longitude of mounting position as precise to two places of decimal Latitude the latitude of mounting position as precise to two places of decimal 4 3 9 MDA Settings Network FTP SMTP HTTPS aaz gos Motion detection alarm State Camera name User name Password Serwer F Port Ho Save Cancel Figure 4 18 MDA Settings In MDA settings interface you can set the Sever which the motion detection alarm uploads to State disable or enable motion detection alarm upload When it s on you can set camera name user name
17. Infinova V6812 TOO Series HD 1MP IP Minidome Camera Notice Copyright Statement This manual may not be reproduced in any form or by any means to create any derivative such as translation transformation or adaptation without the prior written permission of Infinova Infinova reserves the right to change this manual and the specifications without prior notice The most recent product specifications and user documentation for all Infinova products are available on our web site www infinova com Trademarks Infinova is a trademark of Infinova All other trademarks that may appear belong to their respective proprietors FCC Warning The V6812 T00 Series HD 1MP IP minidome cameras comply with the FCC rules Operation 1s subject to the following two conditions e This device will not cause harmful interference e This device must accept any interference received including interference that may cause undesired operations The V6812 T00 Series HD 1MP IP minidome cameras have been tested and found to comply with the limits for a Class A digital device pursuant to the FCC rules With these rules and regulations being obeyed to maintain the good working condition of device the operation is not supposed to be affected by the external interruptions under certain circumstances This device is electromagnetic so all the installation and application processing along the device has to follow strictly to the manual or it may hamper the
18. Removable ICR Filter for Day Night switching Onvif Profile S H 264 High profile M JPEG encoding Full frame HD video output with the resolution up to 1280x720 30fps High encoding efficiency low data rate and high image quality Smooth videos and clear images of moving objects free from ghost and smear Provide WDR function Supports storage with TF card Supports active video tampering Motion detection and privacy mask Bi directional audio G 711 Supports alarm input and output PoE power supply Surface Bracket or Recessed Mount 3 axis adjustment 1 3 System Requirement Minimum PC Requirements CPU Intel Pentium 4 2 4 GHz or above RAM 512 MB or above Network Port 100M Ethernet port Operating System Microsoft Windows 7 Microsoft Windows XP IE browser version Microsoft Internet Explorer 6 0 or above 1 4 Product Model This manual is for the following models V6812 T00205SP Megapixel IP minidome camera 3 axis Day night 1 3 inch CMOS sensor H 264 M JPEG 1 0Mpx PoE Surface mount 2 8 12mm vari focal lens V6812 T0020PP Megapixel IP minidome camera 3 axis Day night 1 3 inch CMOS sensor H 264 M JPEG 1 0Mpx PoE Bracket mount 2 8 12mm vari focal lens V6812 TOO20RP Megapixel IP minidome camera 3 axis Day night 1 3 inch CMOS sensor H 264 M JPEG 1 0Mpx PoE Recessed ceiling mount 2 8 12mm vari focal lens 1 5 Specifications Angle of View 929 27 20 Horizontal iik Camera Angle X Panning
19. Settings Click Camera in the navigation bar to enter the interface shown as below Basic set Exposure Effect set White balance Reset Flicker frequency 50Hz 60Hz BLC C On e Off DWDR C On Off Contrast Enhance 4 Recommendation v Save Figure 4 22 Basic Settings 4 4 1 Basic Settings You can set the following parameters Flicker frequency 50Hz or 60Hz Enable or disable backlight compensation or digital WDR Contrast Enhance 1 6 levels match with 6 kinds of Gamma curve separately If it is set to Auto the system will adjust automatically 4 4 2 Exposure Settings Basic set Exposure Effect set White balance Reset Exposure set Scene Auto aperture On M ICR control Auto mode y ICR switch time os H Scene Outdoor y AGC av idi Shutter speed g Manual AGC AE target Save Figure 4 23 Exposure Settings Exposure set auto aperture ICR control ICR switch time scene AGC shutter speed and manual AGC can also be set in this interface Exposure Set Manual Scene and Shutter priority In the Scene mode indoor or outdoor can be selected and AGC can be set maximum 64X if set to manual mode shutter speed can be set from 1 25s to 1 8000s and manual AGC can be set to 1X to 64X yet the scene and AGC are nonadjustable if set to shutter priority mode the shutter speed and AGC can be set Auto Aperture to enable or disable auto iris ICR Control Auto mode Night Day
20. alarm Local Contact I O out is triggered by I O alarm in motion detection alarm shelter alarm SD card out network link down or IP address conflict Default Local Contact Net Contact I O out is controlled by the surveillance management software Note This function needs to be supported by digital video surveillance management software like V2216 If Net Contact is selected users have to set Alarm Server IP the same as the IP address of V2216 CMS server After related setting to V2216 finished users can remotely control the relay via V2216 software For detailed information please refer to V2216 manual Alarm Server IP used to set the IP address of alarm server If alarm occurs it will inform the alarm server Alarmout Contact Users can set the relevant alarm response ways for I O alarm in motion detection alarm shelter alarm SD card out network link down or IP address conflict which can be Alarm out 1 1f Net Contact is selected Alarm output 1 on the web page is unavailable SD card Mail FTP or Audio After setting completed click Set button to take effect Alarm Schedule V6812 TO0O series camera can set the effective alarm schedule Select the alarm period if Sunday is selected alarm will be enabled during the set period of each Sunday if everyday is selected alarm will be enabled during the set period of everyday and then set the time period Enter the start time and end time in the 24 hour forma
21. and video settings interface Indicate audio input output disabled Click the buttons to enable audio input output and then the buttons will be shown as tl Indicate that the motion detection and privacy mask functions are disabled Click the buttons to enable them and then the buttons will be shown Note only when motion detection or privacy mask is enabled you can set the corresponding function in Audio amp Video Settings refer to Section 4 5 3 or 4 5 4 for details Note the login web page language should be set to the same as that of PC s operating system Click the option tab Settings to enter the system setting interface Infinova no network Mini Dome Camera Live View Settings System dem Time Awan ed Bak informatica Network Camera Mehr settings Audio video Alar Record Alar venting NTP setiinga Hatt video sertis MIPEG video seltiogs 2j Figure 4 3 Settings Interface With the help of navigation menu on the left Super user can perform the following operations Basic Information View Time Settings and Advanced Settings Network Settings Camera Settings including Basic Set Effect Set White Balance Reset Audio amp Video Settings Alarm Settings Account Settings Add Delete User Change Password Log etc Note The following instructions are used for the super user 4 2 System Click the navigation bar System and it displays the following three option tabs Sys
22. cording saving path in the following interface Photo Saving path 2 UnhiP yee ieture Formar jpg i Wideo Saving path C unfiPli en Videa Format a x Figure 4 34 Storage Path Default photo saving path C MnfiPlayerAX Picture Default video saving path C MnfiPlayerAX Video Photo and video formats can also be set The default photo format is jpg and the default video format is avi To change the saving path click the button Browse and select the path from the popup dialog box 4 5 8 Audio Settings Sample rate 8K Format G711 U Figure 4 35 Audio Settings Sample Rate 8K Format G 711 U 4 6 Alarm Settings Click Alarm in the navigation bar to display the following Alarm Settings interface Alarm configuraticr Wo In 1 iro In 2 Alarm out contact Alarm server 1 IP Alarm server z IP Alarm server 3 IF Alarm out contact Note Enable MIREG before Mall or FTP is selected VO out 1 FH SD car tu eu Loin 1 Loin 2 Morin area 1 Hoton arta 2 Motion area 3 Moton area 4 Shelter area EE IR E md I RE Rl Rl ul Network link down aa CT LI 1 address conflict Alarm schaedule ca Sh St m z z T u et tj a oc Everyday Figure 4 36 Alarm Settings Alarm Configuration I O In 1 I O In 2 Settable 2 channel alarm inputs Each alarm input has 2 modes Grounded Circuit or Open Circuit Alarmout Contact used to set sending way of
23. ench T20 and take off the bubble Step 2 Install camera module Install the camera module to the ceiling with 3 tapping screws Drill screw holes and cable hole at the desired position as per Figure 2 1 Screw holes 3 04 5 Cable hole 035 0 Unit mm Figure 2 1 Figure 2 2 Note The camera supports storage with TF card See the figure below for TF card slot TF card slot Figure 2 3 The size of TF card is up to 32GB Step 3 Adjust camera angle Adjust the panning angle according to your surveillance direction Loosen Screw A to adjust tilting angle then fasten the screw Adjust the rotating angle to ensure upright video Adjust the rods in the lens to focus clear e eS UT LL U DEZ Panning 0 360 Tilting i L W Screw A Qe Rotating 0 360 Figure 2 4 Step 4 Install dome bubble Install the bubble flange to camera module Align the screw holes of the two parts and fasten the 3 Torx T20 screws with the L Shaped Torx wrench T20 With all the procedures finished user should further confirm whether each part of the device is properly and firmly connected Figure 2 5 Dimensions Unit inch in the parentheses is mm 25 32 135 0 Infinova
24. file attribute In the download list file total size status and process will display Click the button Start and then the files in the list will be downloaded in order The process shows 100 after downloading is finished Click the button Open to enter download content 4 8 Account Settings The default super user is admin password admin Super user can add delete common user and change the password of common users Super user cannot change his own password A maximum of 8 accounts are supported Detailed instruction about how to add and delete user are addressed below Click the Account option tab in the Settings interface the following account information will display The Num item shows the current user number In Property column 9 stands for super user stands for common user In means to edit user information x Operation column means to delete See figure below User name Property Operation m Figure 4 43 Account Settings 1 Add Users 1 Click Add User b enter the interface of Add a User Add a User Figure 4 44 Add a User 2 Enter the desired User Name and Password Note User name and password shall include letter number and underline only No special character is allowed The string length of user name is legal between 1 and 24 characters and that of password is between 5 and 20 characters 3 Click OK button If the setting is successfu
25. her Figure 2 12 With all the procedures finished user should further confirm whether each part of the device is properly and firmly connected 2 3 Bracket Mounting Note V6812 T0020PP minidome camera supports bracket mount V1760 series screw thread bracket is recommended Step 1 Install adapter to bracket Screw the adapter to the bracket Figure 2 13 Step 2 Install camera module Loosen the 3 Torx T20 screws with an L Shaped Torx wrench T20 and take off the bubble Install the camera module to the adapter with 3 M4X6 pan head screws lt L R So n M mu E ou Figure 2 14 Step 3 Adjust camera angle Adjust the panning angle according to your surveillance direction Loosen Screw A to adjust tilting angle then fasten the screw Adjust the rotating angle to ensure upright video Adjust the rods in the lens to focus clear Panning 0 360 Rotating 0 360 Figure 2 15 Tilting 75 75 Step 4 Install dome bubble Install the bubble flange to camera module Align the screw holes of the two parts and fasten the 3 Torx T20 screws with the L Shaped Torx wrench T20 q L HJD Figure 2 16 With all the procedures finished user should further confirm whether each part of the device is properly and firmly connected CHAPTER III IE BROWSER SETTINGS When view the video the user need t
26. icking the below arrows Click Delete logs a prompt will come out Then click Yes to clear logs APPENDIX MAGNETIC RING FILTER INSTRUCTION To reduce electromagnetic interference that power supply generates it is necessary to install a magnetic ring filter with the power cable of Infinova front end IP device To install a magnetic ring filter with power supply Step 1 Open the magnetic ring filter and lead the power cable through Step 2 Wire the power cable on the magnetic ring filter 3 rounds or more Make sure the filter can be well closed Step 3 Close the magnetic ring filter Notice The magnetic ring filter should be installed no more than 50 mm away from the power output connector As shown in Figure 3 the cable length from A to B should be 50mm at most Figure 1 Closed magnetic ring filter Figure 2 Open magnetic ring filter Figure 3 Power cable with magnetic ring filter APPENDIX II QUESTIONS amp SOLUTIONS The following table describes the symptoms causes and solutions for the problems Symptoms Possible Causes Solutions Power supply failure Repair or replace power supply Immediate startup after Restart 10 seconds later The network power off after power off camera does If PoE power supply is used Shorten the length of the not perform too long transmission distance power supply network initiation after may make the power of the cable or replace Power power on Power Supply Switcher Supp
27. l the new user name will appear in the account list Take new user user1 as an example Add uper 5 User name Property Operation admin F r Figure 4 11 2 Delete Users In the Account setting interface click button of the Operation item to delete user The following dialog box will display Microsoft Internet Explorer 2 Are you sure to delete the user Figure 4 45 Click OK button the selected user would be deleted and the account list would be automatically updated 3 User Password Change Click 1 button in the account list the dialog box of Edit User Information will pop up Figure 4 46 Input the old password enter the desired new password for twice and then click OK button the following picture will appear Microsoft Internet Explorer A Edit password successfully Figure 4 47 4 9 System Log Click the Log option tab the date time and log information will appear on the right of the screen Date Time 2012 3 35 apo Li i 1 20 1 Ult UP 10 Do System start D SYSTEM start Tisi System spart app change Gateway to 192 168 160 254 apo change netmasx to 255 255 248 0 app change IF to 192 168 162 151 App system start app image server or encode server Ent started F Gora 1 i Delete logs Figure 4 48 It can display 30 logs on a page The user can turn over the pages or skip to the desired page by cl
28. lt as 3 After all settings finished click Save button to display OSD on the video To cancel OSD set it to Off and then click the button Save See the figure for OSD Mode 2 Text 1 On X Y 0 99 o o Context 323232 Text 2 On X Y 0 99 o o Row 1 Row 2 Row 3 Row 4 Row 5 Date OSD On C Off X Y 0 99 99 o Save Figure 4 29 OSD Mode 2 Only if Text 1 Text 2 and Date OSD are set to On you can set the text content and the display position of text and date Context Enter the text content in the box of Context Text 2 supports five row display and each row allows up to 40 characters lower upper case letters and 0 9 X axis amp Y axis The title axis location Both X axis and Y axis can be any of whole numbers from 0 to 99 Font Size Set the font size to be displayed The bigger the value is the larger the font size 1s Default as 3 After all settings finished click Save button to display OSD on the video To cancel OSD set it to Off and then click the button Save 4 5 3 Privacy Mask V6812 TO0O series camera supports 4 privacy masks If there is certain location within the surveillance area where operators are not allowed to see and thus Privacy Mask can be applied System covers and shields the sensitive area via Privacy Mask setting to avoid operators observing certain sensitive locations on monitor Note do turn on privacy mask functio
29. ly Switcher of larger insufficient power If PoE power supply is used Disconnect other electrical connection to other electric appliance appliance make the ground level not in the correct level The plug in for viewing image Refer to the Plug in is installed incorrectly Installation to reinstall it No video signal Network camera s IP address Set the unique IP address conflicts with other user s IP address Vi i Manually adjust the camera S Manual focus 1s not precise Harsa focus carefully displayed APPENDIX Ill CABLE DIAMETER CALCULATION AND LIGHTNING amp SURGE PROTECTION Relation between 24VAC Cable Diameter and Transmission Distance In general the maximum allowable voltage loss rate is 10 for AC powered devices The table below shows the relationship between transmission power and maximum transmission distance under a certain specified cable diameter on condition that the 24VAC voltage loss rate is below 1096 According to the table if a device rated at 50W is installed 17 meter away from the transformer the minimum cable diameter shall be 0 8000mm A lower diameter value tends to cause voltage loss and even system instability 0 8000 1 000 1 250 2 000 Distance ft m O o see 5e wes en 9 sw sm en ome Pt oes vo mo Lightning amp Surge Protection The product adopts multi level anti lightning and anti surge technology integrated with gas discharge tube p
30. mmx181mm Unit Weight 1 06lbs 0 48kg Shipping Weight 2 01Ibs 0 91kg Applicable Protocols 1 6 Precautions 1 Do not drop the camera or subject it to strong knock Do not point the camera lens toward the sun or other strong light Do not install the camera in environment with temperature beyond the acceptable range from 10 C to 50 C 4 Never let liquid of any kind flow into this unit 9 Do not directly touch the CMOS element If it is necessary to clean the element use a soft cloth moistened with alcohol to wipe off the dust If any abnormality occurs make sure to unplug the unit and contact your local dealer This camera features AGC circuit so when the camera is applied under low illumination sensitivity will enhance automatically making images look rough which is normal Under the default setting the lens has been adjusted till the object in a 1 5m distance becomes clear The lens can be readjusted as per the actual surveillance scenes The camera power supply can be PoE 10 Firstly perform network settings after login Gateway IP address should be set to the IP address of the gateway that the device connects to 11 The IP address of the device should not conflict with other IP address or else no video will be available CHAPTER Il INSTALLATION INSTRUCTION 2 1 Surface Mounting Step 1 Take off the bubble Loosen the 3 Torx T20 screws with an L Shaped Torx wr
31. n in Live View interface before privacy mask setting see Section 4 1 ElZone 1 Draw Mame EZone 2 Draw Mame DZone 3 Ozone 4 Figure 4 30 Privacy Mask Settings How to set the privacy masks Tick the box of motion detection area number Click the button Draw with the mouse press the left mouse button and drag on the video till a blue frame displays on the screen Then click the button Save with the left mouse button and the blue frame changes into black which indicates a successful setting To cancel a privacy mask just cancel the box ticking 4 5 4 Motion Detection I Zone 1 Drm Mame gate Sensitivity 50 ey Em Cancel LlZone 2 Ozone 3 Dzone d Figure 4 31 Motion Detection Settings V6812 TO0O series camera support motion detection Users can easily set the motion detection areas up to 4 with the mouse Note do turn on motion detection function in Live View interface before motion detection setting see Section 4 1 Tick the box of Zone number to be set If the motion detection area has been set a blue frame will be displayed on the screen How to set the motion detection area How to set the motion detection area Tick the box of motion detection area number Click the button Draw with the mouse press the left mouse button and drag on the video till a blue frame displays on the screen Then click the button Save with the left mouse button and
32. nce budget According to system update requirement submitted by user we will send update letter for confirming the version of the product and provide the latest software for download and help user to update the V6812 T00 series camera Follow the steps below to update software Click Browse button on the interface and the file selection dialog box will pop up Choose file Look in 3 update v E 4 My Recent Documents Desktop D m M yN etwork File name update aces Files of type All Files Cancel Figure 4 6 Select update file and press Open button The selected update file will be displayed in the Software Update box After that click Submit button to update software the following information will appear 9 When procezz finizhed the zyztem will reboot Ern Are you sure to continue Figure 4 7 Click Yes button run the program to finish the update The response time is due to the program type You may wait a long time for some program Do not power off during the update process Power off will make update fail even damage the original program or unable to update again After update successfully it needs to reboot the system There is time prompt in the web page during reboot After reboot it will skip to new web page to run new program Note Available only for the super user Factory Settings V6812 TOO series camera provides online rese
33. o adjust the IE browser of the monitor or other video devices and set proper system function based on the following instructions e Support IE browser version Internet Explorer 6 0 or above e Must install InfiPlayerAX control and equip with Directx 9 0c 3 1 Equipment Connection V6812 TO0 series IP minidome camera can be directly connected to a computer or connected to a network Note Check whether the connection is tight or not before power on 3 2 Software Installation The installation procedures of V6812 TO00 series camera image software are listed as follows 1 Login First start IE browser and enter IP address Enter user name and password in the pop up login interface The default IP address is http 192 168 1 100 the default subnet mask is 255 255 255 0 and the default gateway IP address is 192 168 1 254 For normal access correctly set local IP parameters before system login Do log in the system with the default super user for the first time to run the software The default Super User is admin password admin 2 Install and run Control There are two ways to install control Method 1 The prompt message as below will come out in live view window after a successful login Click the link to run or store the exe file then run it Attention Please allow running INFINOVA add ins If it couldn t done automatically please click here to install manually and refresh the page after that Figure 3 1 If
34. ower resistor and TVS tube The powerful lightning and surge protection barrier effectively avoids product damage caused by various pulse signals with power below 4kV including instantaneous lightning surge and static However for complicated outdoor environment refer to instruction below for lightning and surge protection The product features with dedicated earth wire which must be firmly grounded As for surveillance sites beyond the effective protection scope it s necessary to erect independent lightening rods to protect the security devices It s recommended to separate the lightning rod from the mounting pole placing the rod on an independent pole as shown in the figure below If the product has to be installed on the same pole or pedestal for lightning rod there should be strict insulation between the video cable BNC terminal power cable control cable and the standing pole of the lightning rod For suburb and rural areas it s recommended to adopt direct burial for the transmission cables Overhead wiring is prohibited because it s more likely to encounter lightning strike Use shielded cables or thread the cables through metal tubes for burial thus to ensure the electric connection to the metal tube In case it s difficult to thread the cable through the tube all the way it s acceptable to use tube threaded cables only at both ends of the transmission line yet the length in burial should be no less than 15 meters The cable sheath and
35. played as shown in figure below in English operating system Connect to 192 168 160 236 Infinowa User name Password Remember my password Figure 4 1 User Login Do login the system with the default super user for the first time to run the software The system default Super User is admin password admin Input the correct user ID and password and then press OK button to login the system After login is successful the following interface will display Live View Information Figure 4 2 Live View V6812 TO0O series IP minidome camera supports H 264 and M JPEG video compression formats After successful login it enters H 264 major stream live video interface Users can also select H 264 minor stream or MJPEG from the dropdown list of stream type In the H 264 major or minor stream type users can do recording snap shooting and audio in out settings Over browsing videos users can also select a proper video scale Click the button S to snapshoot and E to enter the storage path Default C InfiPlayerA X Picture V6812 T00 series supports local recording Click the recording button to c start recording when the button changes to click it to stop recording During local recording REC appears on the video screen Click the button to enter the recording storage path Default C InfiPlayerAX Video Users can set the snap shootting and recording storage path in the audio
36. pt in the web page during reboot After reboot it will skip to new web page Note Available only for the super user 4 3 Network Settings Click Network in the navigation bar and the following interface will display HTTPS 803 1 gis IP address Subnet mask Default gateway 1 1 104722 Primary DIS server 152 155 13 152 158 1 4 sry ONS semer Save Heartbeat server IF Heartbeat inter al Figure 4 9 Network Settings 11 options tabs are available Network FTP SMTP HTTPS 802 1X QOS IGMP SIP MDA DDNS and UPnP 4 3 1 Network Settings IP mode support both IPv4 and IPv6 modes Network parameters are slightly different under different IP modes IP mode DHCP IP address Subnet mask Default gateway Primary DNS server Secondary DNS server IPv4 v O On O off 10 82 21 83 _ 10 82 21 1 192 168 1 3 19216814 Network IP mode DHCP Link address IP address Default gateway Figure 4 10 Network Settings Under IPv4 mode users can enable or disable DHCP When it is disabled users can set Unit IP address Subnet mask Gateway and DNS server IP address manually Notes The system indicator quickly flickers for 5s after the network settings completed Users can also enable disable PPPoE in this interface If enabled users can set the user name and password V6812 T00 series camera supports heartbeat function In SNMP settings set
37. s The camera provides 7 Scene modes Normal Anti Fog Motion Entrance Natrium Sharpen USrMode Each mode matches with a group of parameters such as brightness sharpness hue contrast saturation and 3D denoise In the Mode call users can set effect mode call status and call period 4 4 4 White Balance Settings Mode Red gain Blue gain Save Figure 4 26 White Balance Settings The camera has rich white balance modes including Auto Manual Incandescent light Cool white fluorescent light Sun light Cloudy and Natrium light If set to manual mode you can set the red gain and blue gain 4 4 5 Reset In the interface you can restore all the camera parameters to the factory default settings 4 5 Audio amp Video Settings Click the button Audio amp Video in the navigation bar to display the following interface Video Privacy Motion Shelter Link config Path Resolution Frame rate GOV number Bit rate CER Bit rate 0000 kbps 1000 10000 Save Figure 4 27 Video Settings Click the related option tab to enter the setting interface 4 5 1 Video Settings Users can set the video parameters in the format of H 264 major or minor stream and MJPEG stream such as resolution frame rate and IP rate Resolution For H 264 major stream the resolution comes up to 1280x720 with 1024x768 and 800x600 optional For H 264 minor stream the resolution comes to 720x576 720x480 640x480
38. t The end time must be larger than the start time 4 7 Record Management V6812 TOO series IP cameras support storage with SD card In the Record Management interface you can set the recording parameters replay and download the recorded videos 4 7 1 Record Settings Settings Replay Recording control Recording video type Major stream O Minor stream SD card full 9 Overwrite O Stop Recording mode O Alarm triggered O Always O Close Save Note Alarm trigger still need to associate the SD Card in the alarm page Peripheral equipment manage SD card state State Mounted write protect Off Used space 5 78GB Total space 14 92GB SD card operation Reject Format Figure 4 37 Record Settings Recording video type Select the type of videos to record major stream or minor stream SD card when full Overwrite or Stop Overwrite means newly recorded videos automatically overwrite the previous videos when the SD card is full Stop means recording stops when the SD card is full Recording mode Event triggered Always Close If Event Triggered is selected the event triggered can be Network disconnection or alarm If Network disconnection is selected recordings are automatically triggered during the period of network breaking if Alarm is selected also with SD card selected under alarm out contact in the alarm interface recording is automatically triggered when alarm occurs You can view the total size used
39. t function which greatly facilitates reset adjustment Select Keep current IP unchanged click Reset button and the system will pop up a message as below Microsoft Internet Explorer 2 y The operation will lead all the configurations not including IP to default Factory settings Cancel Are you sure to continue Figure 4 8 Click OK all the parameters excluding IP address will be reset to the factory default settings If Keep current IP unchanged is unselected the IP address will be reset to the factory default settings There is time prompt in the web page during reset After reset it will skip to new web page If current IP unchanged you can access web page directly If IP address resets to 192 168 1 100 you can t access web page Then you have to set PC s IP address to 192 168 1 section such as 192 168 1 25 After that access web page to change camera s IP address and save PC s IP address will restore to the corresponding section Note 1 To avoid error happens the operation of online reset function should be performed under qualified personnel s guide 2 Default IP address is 192 168 1 100 and default subnet mask is 255 255 255 0 3 Do not power off during reset or else the reset will fail Online Reboot Click Reboot button the dialog box This operation will take 75 seconds are you sure to continue pop up Click OK and the system will restart There is time prom
40. tem Time and Advanced as shown in Figure 4 3 4 2 1 System Information The initial interface of System Settings displays related system information such as basic system information network settings NTP settings alarm settings H 264 MJPEG video settings etc 4 2 2 Time Settings System Time Advanced Time zone settings Syne miw Figure 4 4 Time Settings Time Zone Settings Time Zone Select the desired time zone in the scroll box and then click Save to save it There are 33 time zones for your selection If Daylight Saving Time is applied in your region please enable the daylight saving time After settings completed please click the button Save NTP Settings Set the NTP server s IP address synchronization interval etc After completed please click the button Save Sync now There are two sync modes local sync and NTP sync Local Sync means the system time is consistent with that of local PC In the NTP Sync mode the system will automatically adjust time to the same as that of NTP Server 4 2 3 Advanced Settings System Time Advanced File import Factory settings Press The button f reset al rhe parameters fo the factory default Maintain current IP ndow will reload after it Reboot Figure 4 5 Advanced Settings Software Update Free software update is provided for V6812 T00 series camera and this update service can reduce system maintena
Download Pdf Manuals
Related Search