ATREB215-XPRO
Contents
1. Table 3 2 Xplained Pro Extension Header Pin Number Name Description 1 ID Communication line to the ID chip on extension board 2 GND Ground 3 ADC Analog to digital converter alternatively positive part of differential ADC 4 ADC Analog to digital converter alternatively negative part of differential ADC GPIO1 General purpose lO GPIO2 General purpose lO PWM Pulse width modulation alternatively positive part of differential PWM 8 PWM Pulse width modulation alternatively positive part of differential PWM 1 http store atmel com CBC aspx q c 100113 Atmel REB215 XPRO Extension Board USER GUIDE 9 42398A MCU 03 2015 GEU I NN NN IRQ GPIO Interrupt request line and or general purpose 1 0 10 SPI SS B GPIO Slave select for SPI and or general purpose lO 11 TWI SDA Data line for two wire interface Always implemented bus type 12 TWI SCL Clock line for two wire interface Always implemented bus type 13 USART RX Receiver line of Universal Synchronous and Asynchronous serial Receiver and Transmitter 14 USART TX Transmitter line of Universal Synchronous and Asynchronous serial Receiver and Transmitter 15 SPI SS A Slave select for SPI Should be unique if possible 16 SPI MOSI Master out slave in line of Serial peripheral interface Always implemented bus type 17 SPI MISO Master in slave out line of Serial peripheral interface Always implemented bus type 18 SP2. Furthermore the manufacturer must maintain a copy of the modules documentation and ensure the final product does not exceed the specified power ratings antenna specifications and or installation requirements as specified in the user manual If any of these specifications are exceeded in the final product a submission must be made to a notified body for compliance testing to all required standards Important The CE marking must be affixed to a visible location on the OEM product The CE mark shall 6 3 6 4 consist of the initials CE taking the following form The CE marking must have a height of at least 5mm except where this is not possible on account of the nature of the apparatus The CE marking must be affixed visibly legibly and indelibly More detailed information about CE marking requirements you can find at DIRECTIVE 1999 5 EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL on 9 March 1999 at section 12 Canada IC The ATREB215 XPRO Module complies with Industry Canada specifications RSS 210 and RSS GenlC ID for ATREB215 XPRO is 11019A 091982 ATREB215 XPRO is limited modular approved and requires separate approval for this module when used on an application board User manuals for licence exempt radio apparatus shall contain the following or equivalent notice in a conspicuous location in the user manual or alternatively on the device or both This device complies with Industry Canada licence exempt RSS standa
3. TXDN B Receive 4 Ground 5 TXCLKP A Receive 6 TXCLKN A Receive 2 Ground 4 2 4 Current Monitoring J1 J1 enables current monitoring using an external multimeter Connect multimeter between J1 1 and J1 2 and measure current used Warning When not monitoring current the strap need to be inserted in order to provide power to the board Table 4 7 J1 Current measurement J1 1 3 3V pin on the AT86RF215 J1 2 3 3V on extension board 4 3 Board GUI 4 3 1 LEDs There are two LEDs available for use by application SW Table 4 8 LEDs D1 Green User defined function i D2 Yellow User defined function 4 3 2 Button There is a button to reset the RF215 device Table 4 9 Buttons SW1 RSTN Reset press to reset 4 3 3 SMA Connectors There are two SMA connectors one 2 4GHz transmit and receive and one for Sub 1GHz transmit and receiver Table 4 10 SMA connectors SMA 1 RF input output for Sub 1GHz Transceiver SMA 2 RF input output for 2 4GHz Transceiver 4 4 U2 Serial EEPROM The REB215 contains a serial EEPROM AT24MAC602 and factory programmed MAC addresses available through the I2C interface of J100 The memory organisation is as documented in Persistent Memory on page 14 The structure is located from EEPROM address 0x00 device address 1010 Atmel REB215 XPRO Extension Board USER GUIDE 13 42398A MCU 03 2015 5 Persistent
4. device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation FCC 15 19 The internal external antenna s used for this mobile transmitter must provide a separation distance of at least 20cm from all persons and must not be co located or operating in conjunction with any other antenna or transmitter Installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance This device is approved as a mobile device with respect to RF exposure compliance and may only be marketed to OEM installers Use in portable exposure conditions FCC 2 1093 requires separate equipment authorization Modifications not expressly approved by this company could void the user s authority to operate this equipment FCC section 15 21 This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful inte
5. use in military or aerospace applications or environments unless specifically designated by Atmel as military grade Atmel products are not designed nor intended for use in automotive applications unless specifically designated by Atmel as automotive grade
6. 42398A MCU 03 2015 RF215 wn Pin Name Description 17 SPI MISO 44 MISO Master in slave out line of Serial peripheral interface Always implemented bus type 18 SPI SCK 41 SCLK Clock for Serial peripheral interface Always implemented bus type 19 GND Ground 20 VCC Power for extension board 4 2 2 J104 amp J105 J104 and J05 provide to control an external RF analog frontend device external LNA PA Table 4 2 J104 Pin RF215 signal Function 1 FEB24 External Frontend Control for 2 4GHz 2 FEA24 External Frontend Control for 2 4GHz Table 4 3 J105 1 FEBO9 External Frontend Control for Sub 1GHz J105 2 FEA09 External Frontend Control for Sub 1GHz 4 2 3 Serial I Q Data Interface J101 J102 J103 Low voltage differential signalling LVDS interface is used for the data transfer between the AT86RF215 and an external baseband processor Table 4 4 J101 I Q Data Receiver 2 4GHz 1 Ground 2 RXDP24 B Receive 3 RXDN24 B Receive 4 Ground 5 RXCLKP A Receive 6 RXCLKN A Receive 7 Ground Table 4 5 J102 I Q Data Receiver Sub GHz 1 Ground 2 RXDP09 B Receive 3 RXDNO09 B Receive 4 Ground 5 A Receive 6 A Receive 7 Ground Table 4 6 J103 I Q Data Transmitter Pin RF215 signal Function 1 Ground 2 TXDP B Receive Atmel REB215 XPRO Extension Board USER GUIDE 12 42398A MCU 03 2015 RF215 signal Function 3
7. 9 3 05 MB Verification Joti Wireless J Mm 3 4 2013 Version 61 259 0 Updates L Provides hex files for Wireless Performance Analyzer firmware used to demonstrate various features and REB215 XPRO Extension Board USER GUIDE 5 42398A MCU 03 2015 Download and Install Install Wireless Composer This extension does not contain a digital signature Copyright c 2011 Atmel Corporation All rights reserved Redistribution and use in source and binary forms with or without modification are permitted provided that the following conditions are met i Each extension is licensed to you under a License Agreement by its owner not Microsoft Microsoft does not guarantee the extension or purport to grant rights to it By clicking Install you agree with the above license terms if any Restart Atmel Studio allow help to make changes and the Performance Analyzer GUI is available in the Tools menu B Command Prompt v Device Programming Ctrl Shift P 4l Add target Performance Analyzer ra U ge U aa os 8 wnat n 3 If Xplained Pro board is not pre programmed program the board with the Performance Analyzer Firmware available in the Wireless Performance Analyzer Firmware extension or from source code provided in ASF by using the EDBG from Atmel studio Atmel REB215 XPRO Extension Board USER GUIDE 6 42398A MCU 03 2015 2 3 2 4 Atmel r F Z Uu E K
8. Assembly The extension board can be wired into the customer prototype assembly by using an on board connectors all relevant signals are available at on board connectors 1 http www atmel com tools atreb215 xpro aspx Atmel REB215 XPRO Extension Board USER GUIDE 3 42398A MCU 03 2015 2 Performance Analyzer 2 1 Introduction The Performance Analyzer Firmware with the GUI in Atmel Studio Wireless Composer Extension provides basic functional RF tests A quick start guide and general help is provided in Wireless Composer once started 2 2 Program Installation How to install Wireless Composer application follow the steps 1 Install Atmel Studio 2 After installing the application launch Atmel Studio Navigate to Tools gt Extension Manager gt Select Extension Manager to install Wireless Composer Tools Window Help B Command Prompt va Device Programming Ctrl Shift P G Add target E Code Snippets Manager Ctrl K Ctrl B Add in Manager ii Extension Manager Atmel Gallery Profile External Tools Import and Export Settings Customize Options Select Wireless and Wireless Composer http www atmel com tools atmelstudio aspx Atmel REB215 XPRO Extension Board USER GUIDE 4 42398A MCU 03 2015 Atmel Installed Extensions Sort by Highest Ranked Search Available Downloads Available Downloads j Atmel Wireshark Interface Free Cr
9. Atmel USER GUIDE REB215 XPRO Extension Board Introduction This user guide facilitates how to getting started with the Atmel REB215 XPRO extension board The extension board is targeted for evaluating the features and performance of the Atmel AT86RF215 radio transceiver 42398A MCU 03 2015 Atmel Table of Contents Jes Tene 1 1 Getting Start d Ec 3 WAS I II qoi lensaaspocactutidinaancs e ne E A A Ea E aE 3 1 2 Design Documentation and Related Links see ee ee ee ee eee es 3 1 3 Board Assembly iter aee tonne eo oot nene ne EEEE TEETE 3 1 3 1 Connect to a Xplained Pro Board eee ee ee e 3 1 3 2 In Customer Development Assembly eee ee e e ees 3 2 Performance Analyzer eee eee eee 4 vA EB nijore b reo ec 4 2 2 Program Installation reet tp tere ipn RR eia 4 2 3 Using the Performance Analyzer cce 7 2 4 Typical Board Assembly ee ee e HH T 3 Xplained Pro eee 9 3 1 Hardware Identification System see ee ee e eee ee eee ee ee ee eee ee ee eens 9 3 2 Standard Headers and Connectors 22997 Taa aE 9 3 2 1 Xplained Pro Standard Extension Header 9 4 Hardware User Guide sss 11 4 1 Board OVetVIeW neci praserceo rete ERE SERIE Ripa ep MER RLEPE 11 4 2 Headers and Connectors eere ttr nnt ides 11 4 2 1 J100 Xplained Pro Extension Connector 11 42 2 104 amp JIO iiie isse epe Pra xr be E ERR Urin eR e
10. Extension Manager Fk z j Installed Extensions Sort by Highest Ranked Z Search Available Downloads Available Downloads m E Wireless Composer Free 2 Created by Atmel 4 All Provides the Wireless Performance Analyzer Graphical Version 2 2 ASF User Interface used to demonstrate various features p loads 73 Debugging Rating Development NanoMesh Reviews Devi NanoMesh Atmel ATmega256RFR2 amp SAM4E uice Release 1 1 1 Projects Toolchain Free Tools Training Utilities Verification WirelessLibrary Free Wireless Provides source code for the Wireless Performance J Analyzer firmware used to demonstrate various featu k Updates 1 Atmel AVR2054 Serial Bootloader Free A standalone serial boot loader utility for use with Atmel wireless software stacks such as BitCloud RF4 p Wireless Library hex 6 1 Free Provides hex files for Wireless Performance Analyzer firmware used to demonstrate various features and 1 Using the Performance Analyzer To get started 1 Connect the Wireless board assembly with the Performance Analyzer FW programmed to the PC USB connector and power on a COM port should now be available for the kit 2 Power on any other wireless node assemblies of similar frequency running the Performance Analyzer FW and use it as a reference Start Performance Analyzer GUI connect to the kit via the COM port and follow the quick start guide T
11. I SCK Clock for Serial peripheral interface Always implemented bus type 19 GND Ground 20 VCC Power for extension board Atmel REB215 XPRO Extension Board USER GUIDE 10 42398A MCU 03 2015 4 4 1 4 2 4 2 1 Hardware User Guide Board Overview Figure 4 1 Board overview N J102 J108 NEU re 1 j p g a m 1 L j JL J104 2 4GHz Antenna Headers and Connectors The extension board connectors J100 Xplained Pro Extension Connector The Xplained Pro extension connectors used to connect the extension board to the Xplained Pro board Table 4 1 J100 Xplained Pro Extension Header RF215 Description Pin Name 1 ID Communication line to the ID chip on the extension board 2 GND Ground 3 ADC 4 ADC 5 GPIO1 LED D2 Yellow for user function 6 GPIO2 LED D1 Green for user function 7 PWM 13 RSTN RESET to RF215 8 PWM 9 IRQ GPIO 40 IRQ Interrupt request line to uC on Xplained Pro board 10 SPI SS B GPIO 11 TWI_SDA Data line for the two wire interface to AT24MAC602 serial EEPROM 12 TWI_SCL Clock line for the two wire interface to AT24MAC602 serial EEPROM 13 USART_RX 14 USART_TX 15 SPI_SS_A 42 SELN Slave select for SPI Should be unique if possible 16 SPI_MOSI 43 MOSI Master out slave in line of Serial peripheral interface Always implemented bus type Atmel REB215 XPRO Extension Board USER GUIDE 11
12. MEL BE LIABLE FOR ANY DIRECT INDIRECT CONSEQUENTIAL PUNITIVE SPECIAL OR INCIDENTAL DAMAGES INCLUDING WITHOUT LIMITATION DAMAGES FOR LOSS AND PROFITS BUSINESS INTERRUPTION OR LOSS OF INFORMATION ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES Atmel makes no representations or warranties with respect to the accuracy or completeness of the contents of this document and reserves the right to make changes to specifications and products descriptions at any time without notice Atmel does not make any commitment to update the information contained herein Unless specifically provided otherwise Atmel products are not suitable for and shall not be used in automotive applications Atmel products are not intended authorized or warranted for use as components in applications intended to support or sustain life SAFETY CRITICAL MILITARY AND AUTOMOTIVE APPLICATIONS DISCLAIMER Atmel products are not designed for and will not be used in connection with any applications where the failure of such products would reasonably be expected to result in significant personal injury or death Safety Critical Applications without an Atmel officer s specific written consent Safety Critical Applications include without limitation life support devices and systems equipment or systems for the operation of nuclear facilities and weapons systems Atmel products are not designed nor intended for
13. Memory A persistent memory space is allocated to store product specific information The persistent memory is organized as follows Table 5 1 Persistent Memory Structure Revision uint 16 2 bytes MAC address uint 64 8 bytes Board information PCBA Name ASCII string 30 bytes Board information PCBA Serial number ASCII string 10 bytes Board information PCBA Atmel Part Number ASCII string 8 bytes Board information PCBA Revision uint 8 1 byte Reserved 3 bytes XTAL Calibration Value uint 8 1 byte Reserved 7 bytes Reserved 4 bytes CRC uint 16 2 bytes Notes TO terminated ASCII string The MAC address stored inside the MCU is a uniquely assigned ID for each kit and is owned by Atmel User applications can use this unique MAC ID to address the kit Atmel REB215 XPRO Extension Board USER GUIDE 14 42398A MCU 03 2015 6 1 Agency Certifications United State FCC This equipment complies with Part 15 of the FCC rules and regulations To fulfill FCC Certification requirements an OEM manufacturer must comply with the following regulations 1 The ATREB215 XPRO limited modular transmitter must be labelled with its own FCC ID number and if the FCC ID is not visible when the module is installed inside another device then the outside of the device into which the module is installed must also display a label referring to the enclosed module This exterior label can use wording such as the foll
14. This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense FCC section 15 105 ATREB215 XPRO is limited modular approved and requires separate approval for this module when used on an application board Cet appareil est conforme la section 15 des r glementations de la FCC Le fonctionnement de l appareil est sujetaux deux conditions suivantes 1 cet appareil ne doit pas provoquer d interf rences n fastes et 2 cet appareil doit tol rer les interf rences recues y compris celles qui risquent de provoquer un fonctionnement ind sirable 3 ce certificat est valable uniquement en transmission bande ISM 2 4 GHz European Union ETSI The ATREB215 XPRO Module has been certified for use in European Union countries at 2 4GHz ISM Band If these modules are incorporated into a product the manufacturer must ensure compliance of the final product to the European harmonized EMC and low voltage safety standards A Declaration of Conformity must be issued for each of these standards and kept on file as described in Annex Il of the R amp TTE Directive Atmel REB215 XPRO Extension Board USER GUIDE 15 42398A MCU 03 2015
15. da 12 4 2 8 Serial I Q Data Interface J101 J102 J103 12 4 2 4 Current Monitoring J1 sse 13 4 3 Board GU rtt cate evaded declan seek Rer EE E EEEE 13 T SN E IRIURE AR 13 4 9 2 BUON Gucsstcespessereedaee ke pese sor qekepEkPadnrs p Eae AEAEE 13 4 3 9 SMA GConnhecloIS 1 29 as cta ass sR 299 hee teinii pere eieaa 13 44 U2 Serial EEPROM 4 ieri ires erroe nae dE Ra RE DRE RR PEE 13 5 Persistent Memory eee eee eee 14 6 Agency Certifications see eee eee eee 15 od United State FCO s bsc norena on iier ETEEN E irae 15 6 2 European Union ETSI i eerte entier 4 he meon TAn 15 03 Ganada e pec iacamatvd nasdunoteaatar EE 16 6 4 Using Limited Modular Certified Products eee eee 16 7 Document Revision History sse eee ee eee eee 18 REB215 XPRO Extension Board USER GUIDE 2 42398A MCU 03 2015 1 1 1 2 1 3 1 3 1 1 3 2 Getting Started Features The REB215 extension board is a template design for the AT86RF215 Design Documentation and Related Links The most recent and relevant documents and software for the REB215 Xpro extension board Board Assembly The extension board provides wireless communication to an Xplained PRO board or to your own prototype for software development and hardware verification Connect to a Xplained Pro Board The extension board can be connected to any Xplained PRO main board using the extension header In Customer Development
16. eated by Atmel 4 All A Standalone WireShark interface for the Version 6 1 259 0 ASF ATAVRRZUSBSTICK and the RF231 USB Stick in the A Downloads 371 Debugging Rating etre Development E ne compos Free Getting Started s rovides the Wireless Performance Analyzer Graphical iin User Interface used to demonstrate various features Reviews rojects P Toolchain NanoMesh Atmel Tools NanoMesh Atmel ATmega256RFR2 amp SAM4E 3 4 2013 Version 61 259 0 Training Release 1 1 1 Utilities Verification WirelessLibrary Provides source code for the Wireless Performance Analyzer firmware used to demonstrate various featu Updates p Wireless Library hex 6 1 Provides hex files for Wireless Performance Analyzer firmware used to demonstrate various features and Log on to Atmel Gallery Click download Sort by Highest Ranked Search Available Downloads Available Downloads p Atmel Wireshark Interface Free R Created by Atmel 4 All A Standalone WireShark interface for the Version 6 1 259 0 ASF ATAVRRZUSBSTICK and the RF231 USB Stick in the A Downloads 371 Debugging Rating ninini Development leet eee ET EA Getting Started rovides the Wireless Performance Analyzer Graphical Device User Interface used to demonstrate various features Projects Toolchain NanoMesh Tools Training Downloading Wireless Composer 58 Reviews Utilities 1 7
17. ion des autres utilisateurs il faut choisir le type d antenne et son gain de sorte que la puissance isotrope rayonn e quivalente p i r e ne d passe pas l intensit n cessaire l tablissement d une communication satisfaisante Using Limited Modular Certified Products The ATREB215 XPRO Module is certified under part 15 of FCC rules The Modular certification category of this module is Limited Modular The end product The ATREB215 XPRO kit will be used by professional users under lab environment using these modules hence has to undergo compliance testing and receive a new FCC ID for the final product carrying these modules Certification of the final product lies solely with the type of design of the final product Atmel REB215 XPRO Extension Board USER GUIDE 16 42398A MCU 03 2015 Warning Important Important Important Atmel The Original Equipment Manufacturer OEM must ensure that the OEM modular transmitter must be labeled with its own FCC ID number This includes a clearly visible label on the outside of the final product enclosure that displays the contents shown below If the FCC ID is not visible when the equipment is installed inside another device then the outside of the device into which the equipment is installed must also display a label referring to the enclosed equipment This equipment complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this
18. ontains information that identifies the extension with its name and some extra data When an Xplained Pro extension board is connected to an Xplained Pro MCU board the information is read and sent to Atmel Studio The Atmel Kits extension installed with Atmel Studio will give relevant information code examples and links to relevant documents Table 3 1 Xplained Pro ID Chip Content on page 9 shows the data fields stored in the ID chip with example content Table 3 1 Xplained Pro ID Chip Content Data Field Data Type Example Content Manufacturer ASCII string Atmel 0 Product Name ASCII string Segment LCD1 Xplained Pro 0 Product Revision ASCII string 02 0 Product Serial Number ASCII string 1774020200000010 0 Minimum Voltage mV uint16 t 3000 Maximum Voltage mV uint16 t 3600 Maximum Current mA uint16 t 30 Standard Headers and Connectors Xplained Pro Standard Extension Header All Xplained Pro kits have one or more dual row 20 pin 100mil extension headers Xplained Pro MCU boards have male headers while Xplained Pro extensions have their female counterparts Note that all pins are not always connected However all the connected pins follow the defined pin out described in Table 3 2 Xplained Pro Extension Header on page 9 The extension headers can be used to connect a wide variety of Xplained Pro extensions to Xplained Pro MCU boards and to access the pins of the target MCU on Xplained Pro MCU board directly
19. ools Window Help B Command Prompt 76 Device Programming Ctrl Shift P al Add target Performance Analyzer m wane s sm ae R wo ae R on Em i Typical Board Assembly The Atmel SAMAL Xplained Pro Evaluation Kit with REB215 XPRO Wireless Extension board REB215 XPRO Extension Board USER GUIDE 7 42398A MCU 03 2015 Sub GHz Antenna SMA1 i ATSAM4LC Atmel REB215 XPRO Extension Board USER GUIDE 8 42398A MCU 03 2015 3 1 3 2 3 2 1 Xplained Pro Xplained Pro is an evaluation platform that provides the complete Atmel microcontroller experience The platform consists of a series of Microcontroller MCU boards and extension boards that are integrated with Atmel Studio have Atmel Software Framework ASF drivers and demo code support data streaming and more Xplained Pro MCU boards support a wide range of Xplained Pro extension boards that are connected through a set of standardized headers and connectors Each extension board has an identification ID chip to uniquely identify which boards are mounted on a Xplained Pro MCU board This information is used to present relevant user guides application notes datasheets and example code through Atmel Studio Available Xplained Pro MCU and extension boards can be purchased in the Atmel Web Store Hardware Identification System All Xplained Pro compatible extension boards have an Atmel ATSHA204 CryptoAuthentication chip mounted This chip c
20. owing Important Contains FCC ID VW4A091982 This equipment complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation FCC 15 19 3 this certificate is valid only while transmit at 2 4GHz ISM band Provide SMA connector to connect external antenna for mobile transmitter must provide a separation distance of at least 20 cm from all persons and must not be co located or operating in conjunction with any other antenna or transmitter Installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance This device is approved as a mobile device with respect to RF exposure compliance and may only be marketed to OEM installers Use in portable exposure conditions FCC 2 1093 requires separate equipment authorization Important Modifications not expressly approved by this company could void the user s authority to operate this equipment FCC section 15 21 Important This equipment has been tested and found to comply with the limits for a Class A digital device 6 2 pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment
21. rd s Operation is subject to the following two conditions 1 this device may not cause interference and 2 this device must accept any interference including interference that may cause undesired operation of the device 3 this certificate is valid only while transmit at 2 4GHz ISM band Le pr sent appareil est conforme aux CNR d Industrie Canada applicables aux appareils radioexempts de licence L exploitation est autoris e aux deux conditions suivantes 1 l appareil ne doit pas produire de brouillage et 2 l utilisateur de l appareil doit accepter tout brouillage radio lectrique subi m me si le brouillage est susceptible d en compromettre le fonctionnement 3 ce certificat est valable uniquement en transmission bande ISM 2 4 GHz Under Industry Canada regulations this radio transmitter may only operate using an antenna of a type and maximum or lesser gain approved for the transmitter by Industry Canada To reduce potential radio interference to other users the antenna type and its gain should be so chosen that the equivalent isotropically radiated power e i r p is not more than that necessary for successful communication Conform ment la r glementation d Industrie Canada le pr sent metteur radio peut fonctionner avec une antenne d un type et d un gain maximal ou inf rieur approuv pour l metteur par Industrie Canada Dans le but de r duire les risques de brouillage radio lectrique l intent
22. rference in which case the user will be required to correct the interference at his own expense FCC section 15 105 REB215 XPRO Extension Board USER GUIDE 17 42398A MCU 03 2015 T Document Revision History Document Comment revision 42398A 01 2015 Initial document release E i 1 Atmel REB215 XPRO Extension Board USER GUIDE 8 42398A MCU 03 2015 Atmel Enabling Unlimited Possibilities Ei C2 M E9 C G Atmel Corporation 1600 Technology Drive San Jose CA 95110 USA T 1 408 441 0311 F 1 408 436 4200 www atmel com 2015 Atmel Corporation Rev 42398A MCU 03 2015 Atmel Atmel logo and combinations thereof Enabling Unlimited Possibilities and others are registered trademarks or trademarks of Atmel Corporation in U S and other countries Other terms and product names may be trademarks of others DISCLAIMER The information in this document is provided in connection with Atmel products No license express or implied by estoppel or otherwise to any intellectual property right is granted by this document or in connection with the sale of Atmel products EXCEPT AS SET FORTH IN THE ATMEL TERMS AND CONDITIONS OF SALES LOCATED ON THE ATMEL WEBSITE ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTY OF MERCHANTABILITY FITNESS FOR A PARTICULAR PURPOSE OR NON INFRINGEMENT IN NO EVENT SHALL AT
Download Pdf Manuals
Related Search