User`s Manual
Contents
1. e Consult the dealer or an experienced radio TV technician for help 11 Radio Notice for FCC A Caution This FCC Part 15 radio device operates on a non interference basis with other devices operating at this frequency Any changes or modification to said product not expressly approved by Monoprice including the use of non approved antennas could void the user s authority to operate this device This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Notice for Industry Canada This Class B digital apparatus complies with Canadian ICES 008 Cet appareil numerique de la classe B est conforme a la norme NMB 003 du Canada Radio Notice for Industry Canada Caution This IC RSS 210 radio device operates on a non interference basis with other devices operating at this frequency Any changes or modification to said product not expressly approved by Monoprice including the use of non approved antennas could void the user s authority to operate this device This device complies with IC RSS 210 Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation 12. and high frequency response settings 14 Battery Compartment underside The battery compartment is on the underside at the base of the remote control REMOTE CONTROL BATTERY The included remote control ships with a CR2025 Lithium battery pre installed in the battery compartment A plastic film is used to prevent contact so that the battery is not drained during storage and shipping Prior to first use grasp the plastic tab protruding from the battery compartment and pull it out to remove the protective film allowing the remote control to operate When the remaining battery capacity is low the remote control becomes unresponsive or responds intermittently Perform the following steps to replace the battery 1 Pull the battery compartment cover to remove it 2 Replace the existing CR2025 battery with a new one Pay close attention to the polarity markings to ensure that it is inserted properly 3 Push the battery compartment cover to close it CONNECTION DIAGRAM The following diagram illustrates a typical configuration Right Channel Speaker Left Channel Speaker ri HH Remote Control Connect Left Right Channel Speakers To Power adaptor ConnecttoaPC External Audio input signal 2 ss External Audio input signal 1 ts Notes e The AUX 1 input is a low sensitivity input intended for use with devices with a 2000mV maximum signal strengt
3. into this power jack 13 Slave Right Speaker Output Plug the included slave speaker cable into this output on the main left speaker 14 RESET Button The Reset button is recessed below the surface of the panel so that it cannot be accidentally activated Use a paper clip toothpick or other small blunt object to press the recessed button If the system locks up or is otherwise unresponsive press the Reset button to restore it to the factory default settings Remote Control 1 Infrared Transmitter Aim the included infrared remote control at the main left Speaker 2 MUTE Button Press the Mute button to toggle the mute function on off 3 Play Pause II Button When using the Bluetooth input press this button to pause or resume playback Previous 44 and Next gt Buttons When 4 using the Bluetooth input press the M lt button to skip back to the beginning of the current track If already at the beginning of the track press 44 to skip back to the beginning of the previous track Press the gt I button to skip forward to the beginning of the next track TRE and TRE Buttons Use these buttons to adjust the high frequency response Press the TRE button to increase the high frequency response and the TRE button to decrease the high frequency response The high frequency response can be adjusted up to 6dB AUX 2 Button Press the AUX 2 button to select the AUX 2 input Due to the different sensit
4. 2
5. USER S MANUAL OBuetoth Bookshelf Speakers f with USB SAFETY WARNINGS AND GUIDELINES This speaker system is intended for indoor use only Do not expose these speakers to water or moisture of any kind Do not place drinks or other containers with moisture on or near them If moisture does get in or on the speakers immediately unplug them from the power source and allow them to fully dry before reapplying power lf operating these speakers in a humid environment ensure that no condensation occurs Condensation could cause damage to the speaker cone and could cause a short in the amplifier which in turn could cause fire or severe electric shock Do not expose this device to excessively high temperatures Do not place it in on or near heat sources such as a fireplace stove radiator etc Do not leave it in direct sunlight Use only in a well ventilated area Do not use in close confined spaces Ensure that there is at least 12 inches of space around the main speaker to allow for adequate ventilation Unplug the speakers from the power source if they will go unused for a long period of time Prior to operation check the unit and power cord for physical damage Do not use if physical damage has occurred The power supply for these speakers accepts a wide range of input voltages from 100 to 240 VAC 50 or 60 Hz Ensure that your power source is within these limits If not consult a professional electrician or your power com
6. h such as a CD or DVD player e The AUX 2 input Is a high sensitivity input intended for use with devices with an 800MV maximum signal strength such as the headphone output of a mobile phone or television set USB AUDIO This speaker system features a built in DAC and a USB input allowing you to use it as a USB audio device connected to a computer Perform the following steps to configure Windows for use with this speaker system 1 Press the Standby button on the rear panel or on the remote control to power the speaker system on 2 Power on your computer and log in 3 Using the included USB 2 0 cable plug the USB B end into the USB PC port on the rear panel of the main speaker 4 Plug the USB A end into an available USB port on your computer 5 Press the PC button on the remote control to select the USB input The status LED on the main speaker will illuminate green Newer versions of Windows will automatically detect the speaker system and will set it as the default output speaker If it does not perform the following steps depending on your version of Windows Windows XP 029 5 Open Windows Control Panel Double click the Sounds Speech and Audio Devices icon Double click the Sounds and Audio Devices icon Select the Audio tab In the Sound Playback section use the drop down list box to select the MP Bookshelf entry for the Default device Click the OK button to save your changes Windows Vista a
7. ivities of the various inputs the volume should be decreased to minimum or the mute function toggled on before switching inputs The status LED glows yellow BT Button Press the BT button to select the Bluetooth radio input Due to the different sensitivities of the various inputs the volume should be decreased to minimum or the mute function toggled on before switching inputs The status LED glows blue 8 STANDBY Button Press the Standby button to power the system ON or OFF 9 VOL and VOL Buttons Use these buttons to adjust the output volume level of the speaker system 10 BASS and BASS Buttons Use these buttons to adjust the low frequency 11 response Press the BASS button to increase the low frequency response and the BASS button to decrease the low frequency response The low frequency response can be adjusted up to 6dB AUX 1 Button Press the AUX 1 button to select the AUX 1 input Due to the different sensitivities of the various inputs the volume should be decreased to minimum or the mute function toggled on before switching inputs The status LED glows magenta 12 PC Button Press the PC button to select the USB input Due to the different sensitivities of the various inputs the volume should be decreased to minimum or the mute function toggled on before switching inputs The status LED glows green 13 NORMAL Button Press the Normal button to reset any adjustments made to the bass and treble low
8. nd 2 this device must accept any interference received including interference that may cause undesired operation Modifying the equipment without Monoprice s authorization may result in the equipment no longer complying with FCC requirements for Class B digital devices In that event your right to use the equipment may be limited by FCC regulations and you may be required to correct any interference to radio or television communications at your own expense This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
9. nd Windows 7 a9 5 Open Windows Control Panel Click the Hardware and Sound entry Click the Sound entry Locate and double click the MP Bookshelf entry from the list of displayed devices Click the Set Default button to make the highlighted audio playback device the default A white check mark on a green background indicates the default audio device Click the OK button to save your changes BLUETOOTH PAIRING This speaker system contains a Bluetooth radio allowing you to stream audio from your mobile device Perform the following steps to pair your device with the speaker system 1 Power the speaker system ON by pressing the STANDBY button on the rear of the main speaker or on the remote control 2 Press the BT button on the remote control to select the Bluetooth input The system will automatically go into Bluetooth pairing mode The status LED on the main speaker will begin to blink 3 Open the Bluetooth settings on your mobile device and initiate a search for nearby Bluetooth devices 4 From the list of discovered devices select the MP Bookshelf entry If prompted for a passcode input 0000 four zeroes 5 Once the connection is established the status LED will cease flashing and will change to solid blue Notes e Ifthe speaker system is already paired with an active device pressing the BT button in step 2 will cause the system to automatically reconnect with the previously paired device e To delete an e
10. pany for a resolution Do not allow the power cord to be crimped pinched stepped on etc Ensure that the power cord does not present a tripping hazard These speakers have no user serviceable parts Do not attempt to open service or modify them Clean using a soft dry cloth only Do not use chemical cleaners solvents or detergents For stubborn deposits moisten the cloth with warm water Do not subject the speakers to extreme force shock or fluctuations in temperature or humidity Remove the battery if the remote control will go unused for a long period of time The remote control for this device contains a Lithium battery Dispose of the battery only in accordance with local state or federal regulations for electronic wasie INTRODUCTION Thank you for purchasing this Bluetooth Bookshelf Speaker System This powered speaker system features a Bluetooth radio for streaming from mobile devices as well as a pair of stereo auxiliary inputs with RCA connectors It includes a high quality Digital to Analog Converter DAC which allows you to connect it to a computer as a USB audio device Each of the four drivers is powered by a dedicated 50 watt RMS power amplifier ensuring that each driver gets all the power it needs A wireless infrared remote control is included FEATURES e Built in Digital to Analog Converter DAC for use as a USB audio device e Built in Bluetooth v3 0 radio for streaming from mobile devices e T
11. to indicate the selected input and operating mode Solid Blue Bluetooth input selected and actively connected to a device Blinking Blue The system is in Bluetooth pairing mode Solid Green PC mode USB input selected Solid Magenta AUX 1 input selected Solid Yellow AUX 2 input selected Remote Control Infrared Receiver Aim the included infrared remote control at the main left soeaker Speakers Rear re Slave Right Speaker Input Plug the included slave speaker cable into this input on the slave right speaker STANDBY Power Button Press this button to power the system ON or OFF AUX IN 1 Left Right RCA Input Jacks strong signal Connect a line level audio source device to these RCA inputs using the included stereo RCA cable This is a low sensitivity input and is intended for use with modern audio equipment with 2000mV maximum signal strength such as CD players and DVD players 10 AUX IN 2 Left Right RCA Input Jacks 11 weak signal Connect a line level audio source device to these RCA inputs using the included stereo RCA cable This is a high sensitivity input and is intended for use with devices with an 800mV maximum signal strength such as the headphone output of a mobile phone or television set use the speakers as a USB audio device 14 13 12 11 USB PC Input Use the included USB 2 0 cable to connect to a computer to 12 DC 24V Power Input Jack Plug the included AC adapter
12. wo sets of line level stereo AUX inputs e Separate 50 watt RMS power amplifier for each driver 200 watts total e Includes infrared remote control e Adjustable bass and treble controls with 6dB range CUSTOMER SERVICE The Monoprice Customer Service department is dedicated to ensuring that your ordering purchasing and delivery experience is second to none If you have any problem with your order please give us an opportunity to make it right You can contact a Monoprice Customer Service representative through the Live Chat link on our website www monoprice com during normal business hours Mon Fri 5am 7pm PT Sat Sun 9am 6pm PT or via email at Ssupport monoprice com PACKAGE CONTENTS Please take an inventory of the package contents to ensure you have all the items listed below If anything is missing or damaged please contact Monoprice Customer Service for a replacement 1x Main left soeaker 1x Slave right soeaker 1x AC power adapter 1x Infrared remote control with installed CR2025 battery 1x Slave speaker cable 1x Stereo RCA cable 1x USB 2 0 cable 1x User s Manual PRODUCT OVERVIEW Speakers Front 1 4 Woofers One per speaker Main Left Speaker The main speaker contains the amplifiers and Bluetooth radio Slave Right Speaker The slave Speaker is powered and controlled by the main speaker Tweeters One per speaker aoah wh 5 Status LED The LED illuminates in various colors
13. xisting pairing press and hold the BT button on the remote for about 3 seconds TECHNICAL SUPPORT Monoprice is pleased to provide free live online technical support to assist you with any questions you may have about installation setup troubleshooting or product recommendations If you ever need assistance with your new product please come online to talk to one of our friendly and knowledgeable Tech Support Associates Technical support is available through the online chat button on our website www monoprice com during regular business hours 7 days a week You can also get assistance through email by sending a message to tech monoprice com SPECIFICATIONS Signal to Noise Ratio 62dB A weightedq Low Frequency Amplifiers 2x 50W RMS High Frequency Amplifiers 2x 50W RMS Bass Adjustment Range 6dB AUX1 Nominal Input Strength 2000mV RMS AUX2 Nominal Input Strength 800mV RMS Bluetooth Version v3 0 Supported Bluetooth Profiles A2DP AVRCP Built in DAC 44 1 96 kHz DAC Remote Control Battery Type CR2025 3V Lithium battery Main Left Soeaker Dimensions 11 8 x 11 4 x 7 9 800 x 290 x 200 mm Slave Right Speaker Dimensions 11 8 x 10 2 x 7 9 Weight Total 28 5 lbs 12 9 kg 300 x 260 x 200 mm 10 REGULATORY COMPLIANCE Notice for FCC FC This device complies with Part 15 of the FCC rules Operation is subject to the following two conditions 1 this device may not cause harmful interference a
Download Pdf Manuals
Related Search