Hi-Riser - Smirthwaite
Contents
1. Size E T ee ee ee poo opo eee ee ee TableDimensions ooo ro a uum oii WWidih mm 550 5560 600 600 650 650 650 Safety Sides 7 7 7 vvnv o o az ame i o oo I Tam 7 Y Height mm Wall Frame oo orororooreoroaosoa eo ka Storage v o O Shipping Weight kg 80 82 84 86 88 9 92 4 0 FOR YOUR SAFETY STOP Please read these instructions CAREFULLY and THOROUGHLY e DO NOT attempt to install and use this product in a wet room Please follow installation instructions as described in Section 5 carefully and thoroughly e The user should NOT be left unattended whilst on the changing table Always ensure a responsible therapist or carer is in attendance e The Hi Riser changing table height should NEVER be adjusted without a carer in attendance e Always ensure the safety side is in the up position once a patient is on the table e When storing the product vertically up position check to ensure that the locking plunger pin is fully engaged e When not in use for periods of time isolate the electrical supply e Always keep this product away from naked flames cigarettes and sources of heat including open fireplaces radiators and heaters e Regular maintenance checks and cleaning are essential for the safe use of this equipment see care and maintenance section e DO NOT fit parts or accessories of ot2. shown circled opposite e When unlocked use both hands to lower the bed into the horizontal position e Before transferring a patient adjust the height of the bed by using the hand controller Up and Down buttons arrows as shown opposite e With the patient safely transferred onto the bed rotate the safety rail into the vertical position and allow it to drop into its retaining slot check it is in place by gently pulling outwards towards your body e The bench can now be raised to the optimum position which will depend on the carer e o dismount the patient the process is the reverse of the steps described above e Once the patient has been dismounted ensure the bed mattress is wiped as per the cleaning instructions in Section Y e The bench can be stowed away by lifting it up with both hands and when vertical press firmly to slightly compress the mattress listen for a click which indicates that the plunger locking pin has engaged into the locked position Confirm this by gently pulling the bed toward you N B If using a hoist system for patient transfer the patient can be lowered onto the bed when already set at the desired height with the safety rail set to the vertical position 10 7 0 CARE AND MAINTENANCE IMPORTANT Cleaning is recommended on a regular basis To clean the mattress use a damp soft cloth with mild soap Rinse with clean cloth and water DO
3. NOT use solvents abrasives synthetic detergents and wax polishes ALWAYS wipe dry after use ALWAYS keep this product away from naked flames cigarettes and sources of heat including open fireplaces radiators and heaters e For further information please refer to MHRA or Local Authority cleaning guidelines 7 1 MAINTENANCE CHECKS IMPORTANT Regular maintenance checks are required 7 1 1 DAILY CHECKS e Check the mattress for signs of damage or wear and tear e Keep the upholstery and metal parts clean e Check the safety rail can be stowed and locked into the vertical position e Check that the bed rises and lowers when activated by the handset e Check that the bed can be securely stored in the vertical position and that the plunger locking pin engages 7 2 SERVICE INTERVAL The Hi Riser changing table should be serviced every 1 year Servicing must only be undertaken by a Easi Change service engineer or by a Easi Change trained representative 11 8 0 GUARANTEE amp SERVICE The product is issued with a full parts and labour guarantee for 2 years from the date of delivery This guarantee does not apply to accidental damage caused through inappropriate use of the product This guarantee is issued at the discretion of Easi Change Ltd on RIB Return to Base basis If you have any questions or doubts relating to the safety or use of the product please contact us for advice or assistance on T 44 0 8455 192121 E info e
4. 1 12 easi change Hi Riser INSTRUCTIONS FOR USE Codes 3041 3047 3051 3057 CONTENTS PAGE 1 0 INTRODUCTION 1 2 0 ILLUSTRATION OF YOUR HI RISER CHANGING TABLE 2 3 0 TECHICAL DATA 3 4 0 FOR YOUR SAFETY 4 5 0 SURVEYING AND INSTALLATION 5 6 0 HOW TO USE YOUR HI RISER CHANGING TABLE 9 7 0 CARE amp MAINTENANCE 11 8 0 GUARANTEE amp SERVICE 12 9 0 CONTINUOUS IMPROVEMENT 13 10 0 WARRANTY amp AFTERSALE 14 1 0 INTRODUCTION Thank you for choosing the Easi Change Hi Riser changing table The Hi Riser Showering is an easy to use two in one wall and floor mounted showering and changing table The robust and yet slim line design makes it suitable for children and adults of up to 150kg Its versatility enables it to be an ideal solution for bathrooms as well as swimming pools and hydrotherapy environments IMPORTANT These instructions should be read by all therapists and carers using the equipment and should be retained for future reference The product should always be used under adult supervision Any incorrect use of the product and failure to follow the instructions may put the user at risk or impede the function If you have any queries using this product or wish for further copies please do not hesitate to contact Customer Service department on T 44 0 8455 192121 2 0 ILLUSTRATION OF YOUR HI RISER CHANGING TABLE Safety side Bed Wall frame Handset IOW 3 0 TECHNICAL DATA A
5. asi change co uk 12 9 0 CONTINUOUS IMPROVEMENT Easi Change Ltd are committed to continuous improvement to their product range Should you have any suggestions or comments please send them to our product design department at info easi change co uk Easi Change Ltd reserve the right to change the specification or material without prior notice For catalogues help and further information on our products please contact us at Easi Change Ltd 17 Wentworth Road Heathfield Devon TQ12 6TL T 44 0 8455 192121 F 44 0 1626 835428 E info easi change co uk W www easi change co uk 13 10 0 WARRANTY amp AFTERSALE 10 1 Product Information Mode To O Sizes Date of Manufacture Serial Number V DO J I Final Inspection oS o 10 2 Service amp inspection record form Date Procedure Service Personnel 14 easi change Easi Change Ltd 17 Wentworth Road Heathfield Newton Abbot Devon TQ12 6TL T 44 0 8455 192121 F 44 0 1626 835428 E info easi change co uk W www easi change co uk
6. bench using wall and floor fixings care must be taken to survey the junction between wall and floor If this junction has a large radius fillet it may be necessary to space the frame off the wall any such adjustment will impact on the overall installation footprint so must be taken into account when assessing clearances e It is possible using the two leveling bolts to provide stability to the frame at the mating surface with the floor in instances where the customer does not wish to make installation holes in the flooring surface itself e Check for the position of dado rails window sills electrical power points switches etc which may affect the installation e Check there is sufficient room around other facilities e g wash basins toilets etc e Remember to take into account the safety rail dimensions check that the bench would be capable of adjustment over the height range without fouling e Check that doors would be clear and that access is still possible e Inspect the wall to see if padding spacing is required to correct wall imperfections e The Hi Riser requires a 220 240V AC 50Hz or 110V AC 60Hz power supply e The power connection must be made in an area that is kept free from moisture or connected via a waterproofed socket with isolation switch STOP If in any doubt ALWAYS seek PROFESSIONAL ADVICE 5 2 INSTALLATION TOOLS REQUIRED e Electric hand drill with appropriate drill bits for wood and masonry e Set of
7. her manufacturers to this product unless authorised to do so in writing by Easi Change Ltd Failure to follow these instructions will not only invalidate the guarantee but could make the product dangerous to use Easi Change Ltd will not accept liability for any injury or damage incurred through such malpractices Any repairs required must be carried out by Easi Change Lid authorised personnel e lf any part is loose damaged or functioning incorrectly DO NOT use until rectified e The Hi Riser changing table is CE marked This certifies that it meets all relevant European safety requirements e lf you believe the product or any fitted accessory to be faulty at any time DO NOT USE contact Easi Change by telephone on T 44 0 8455 192121 5 0 SURVEYING AND INSTALLATION 5 1 SURVEYING PROCEDURES e Changing benches tables are normally installed in small rooms with limited space In such circumstances it is vitally important to take accurate measurements of the whole room in question and make a plan to scale if possible e Ensure that the intended wall for installation is strong enough to support the weight of the changing bench plus the patient e If the wall is of brick or concrete construction it will be strong enough to support the equipment without the need of the backing board e f the wall is of hollow or soft insulation block construction then we would always recommend the backing board is used e t is possible to install the
8. orily do not repeat in rapid succession as this will put stress on the motor system and can cause damage through overheating The main front cover can now be refitted and fixed into place by sliding it down behind the bench so that the Velcro holds the top firmly Use the studs supplied to fix into place Place a copy of the user instructions on the wall near to the changing bench where it can easily be read ensure anyone that will be using the bench is trained and familiar with correct usage To Mains Power supply Main voltage supply should be taken from out side of the room if in wet or humid conditions It is recommended that the transformer is fitted to the wall besice the wall frame and kept off the floor 24 Volt transformer Actuator Hand set HIDDEN TIMBER SUPPORTS CEILING LEVEL 28 75 728 9mm TO THE STUDS 6 0 HOW TO USE YOUR HI RISER CHANGING TABLE IMPORTANT For non hoist transfers always ensure the safety side is in the fully stowed position down When the user has been transferred onto the Hi Riser table please ensure safety side is in the fully upright position e Ensure that the electrical supply to the changing table is ON e The bed can be lowered from its stowed position by using one hand to gently press the mattress against the frame and at the same time using your second hand to release the plunger locking pin which is situated by the right hand hinge
9. spanners e Tape measure e Spirit level e Hammer e Screw driver e Personal Protection Equipment PPE gloves safety glasses 5 3 INSTALLATION PROCEDURE e Carefully unpack the Hi Riser and lay all parts on to the floor e Check all components are present and check for damage that may have occurred in transit see illustration below Wall Frame Bench frame with mattress and safety side Wall Frame Cover Handset Transformer and plug Fixing screw pack It is strongly recommended that two people carry out the installation due to the weight of the product Store the wall frame cover and backing board if ordered safely until required Offer up the wall frame into the desired position to mark and drill the holes for the fixings adjust the two leveling bolts as required Where a backing board is to be used it should be drilled to take fixing screws minimum 8 check the screws do not interfere with the wall frame when mounted Fit the fixing bolts and loosely fit the frame to the wall or backing board being careful not to trap the electrical cable Before tightening fixings check frame is vertical in all directions and if necessary fit packing to achieve Before offering up the bench frame to the wall frame firstly remove the ball end screw that has been loosely fitted to the left hand hinge The bench frame can now be fixed to the wall frame the two hinge bolts that are loosely fitted to the wall frame sho
10. uld be removed and a small amount of Loctite applied to the first 5mm Offer up the bench and insert the two bolts previously prepared but do not over tighten The bolts must not protrude more than approx 1mm With the bench frame now in place in the horizontal position reconnect the ball end screw previously removed and tighten with the appropriate spanner The bench should now be raised into the vertical position and locked in position Locate the lower end of the gas spring which is fitted to the back of the wall frame and fit to the ball end on the hinge of the bench frame This can be snapped into place by pressing the cup firmly onto the ball end To enable this to be done it might be necessary to disengage the locking plunger and push the bench frame slightly remember to re engage the locking plunger when finished The two side trims may now be fitted using the plastic push fit retainers supplied Check that the gas spring functions correctly and assists in the raising of the bench make sure it is checked with the safety rail fitted Connect the electrical supply and test the bench by raising and lowering to each of the limits of travel to ensure there are no obstructions Confirm the plunger pin works effectively you will hear a distinct click when it engages The 24V transformer can now be fixed to the wall in a suitable position or on a bracket shelf Raise and lower the bench with a load to ensure it is working satisfact
Download Pdf Manuals
Related Search