Matrix 3 - DirectedDealers.com
Contents
1. The system will not disarm but rather reset This prevents you from disabling the system should you wish to disarm it without visually checking the vehicle Pressing a second time after resetting the system will disarm the system Pressing A A during the first six seconds of the triggered sequence will disarm the security system immediately The six second timer is provided for your convenience in case that the system is acci dentally triggered O 2001 directed electronics inc 9 disarming without a transmitter This feature allows you to disarm the security system without the remote transmitter should it be lost damaged or disabled In order to disarm the system without a remote transmitter you must have the vehicle s ignition key and know where the Valet switch is located Be sure to check with the installer for the loca tion and the number of presses of the Valet switch required to disarm the system oS To disarm the security system turn the ignition to the on position Press the Valet switch the preset number of times 1 5 times within 15 seconds The system should now disarm If it does not you may have waited too long turn the ignition off and on and try again important The unit can be programmed to respond to 1 5 pulses of the Valet switch for the disarm function Be sure to check with the installer for the desired programming Location of Valet Switch remote controlled chirp muting2. 10 To temporarily turn off the arm or disarm siren chirps use Remote Controlled Chirp Muting Simply press on the transmitter for less than one second before arming or disarming and the confirmation chirp s will be eliminated for that one op eration only If you want the arm disarm chirps turned off permanently your dealer can do this for you 2001 directed electronics inc note The Warning Zone response to lighter impacts is bypassed if the system is armed using Remote Controlled Chirp Muting This ensures that no chirps will be emit ted by the siren in an area you want chirp free The sys tem is still fully capable of triggering Only the Warning Zone response is bypassed panic mode If you are threatened in or near your vehicle you can attract atten tion by triggering the system with your remote Just press for 1 5 seconds and you will enter Panic Mode The siren will sound and the parking lights will flash for the programmed siren duration To stop Panic Mode at any time press again valet mode You can prevent your security system from automatically arming and triggering by using Valet Mode This is very useful when washing the vehicle or having it serviced In Valet Mode the security system will not arm even with the remote transmitter but all convenience functions door locks trunk release etc will continue to work normally To enter or exit Valet Mode 1 Turn the ignition on O
3. Directed security systems including this unit are deterrents against possible theft Directed is not offering a guarantee or insurance against vandalism damage or theft of the automobile its parts or contents and hereby expressly disclaims any liability whatso ever including without limitation liability for theft damage and or vandalism Directed does not and has not authorized any person or entity to create for it any other obligation promise duty or obligation in connection with this security system Make sure you have all of the following information from your dealer A clear copy of the sales receipt showing the following Date of purchase Your full name and address Authorized dealer s company name and address Type of alarm installed Year make model and color of the automobile Automobile license number Vehicle identification number All security options installed on automobile Y Y Y Y Y Y Y VY Installation receipts Bitwriter Clifford Code Hopping DEI Directed Doubleguard ESP FailSafe Ghost Switch Learn Routine Nite Lite Nuisance Prevention Circuitry NPCS Revenger Silent Mode Soft Chirp Stealth Coding Stinger Valet Vehicle Recovery System VRS and Warn Away are all Trademarks or Registered Trademarks of Directed Electronics Inc il 2001 directed electronics inc table of contents Limited Lifetime Consumer arran
4. arming while driving Your system can be armed while driving the vehicle Simply press on your transmitter for 1 5 seconds while the vehicle is running or while the ignition is on The siren will chirp once and then once more to indicate that the ignition is on The security system will not respond to any input except the door triggers and the starter interrupt relay if installed will not be activated The system will disarm automatically whenever the ignition is turned off The siren will chirp twice and the LED will stop flashing 8 2001 directed electronics inc note If programmed for the optional Vehicle Recovery System VRS feature arming with the transmitter will arm the VRS feature See VRS section of this guide disarming To disarm the system press 7A You will hear two chirps and the parking lights will flash twice If the power locks are connected to the system the doors will unlock If the siren chirps either four or five times when disarming refer to the Diagnostics section of this guide This is called Tamper Alert siren silencing This security system proudly offers Siren Silencing Siren Silencing is a feature that makes it possible to silence and reset the system while it is triggering without disarming the system If the system is triggered and the siren has been sounding for longer than six seconds pressing on the remote trans mitter will stop the trigger and return the unit to the armed state
5. Bypass Notification will not occur when using Remote Controlled Chirp Muting or if chirps have been programmed OFF The security system will ignore the input that was active when the system was armed until the input goes away Three seconds later the system will monitor that input normally For example if your vehicle has interior light exit delay and you arm the system before the interior light goes out you may hear Bypass Notification chirps Once the light shuts off however the doors are monitored normally disarming diagnostics 14 Extra disarm chirps are the Tamper Alert If four chirps are heard when disarming the system was triggered in your absence If five chirps are heard a zone was triggered so many times that False Alarm Control Technology FACT has bypassed that zone In either case the LED status indicator will indicate which zone was involved see Table of Zones section The system will retain 2001 directed electronics inc this information in its memory and continue to chirp four or five times each time it is disarmed until the next time the igni tion key is turned on table of zones The zone number is the number of LED flashes used by the system to identify a specific input The standard input assign ments are listed below along with spaces to write in any optional sensors or switches you have had installed Zone Number Dealer Installed of LED Flashes Description Options 1 Insta
6. alarm can recognize as unique Each input to the system is connected to a particular zone Two or more inputs often share the same zone O 2001 directed electronics inc 27 28 A E ILY A COI IVCI ICI ICE CXOEAIHSIU I Here we have listed only some of the many expansion options available Please contact your dealer for a complete list of all the options available to you Audio Sensor Metal on glass glass cracking and breaking glass each produce distinctive acoustic signatures The 506T audio sensor uses a microphone to detect sounds and then analyzes them with proprietary acoustic software to determine if glass has been struck Backup Battery The 520T keeps the system armed triggers the alarm and keeps the starter interrupt active if main battery power is disconnected Car Com Automated Vehicle Locator AVL Your system is compatible with Directed s Valet Car Com and AVL systems Car Com offers a one way pager system that allows many of the security and convenience features of your Directed security system to be operated from any touch tone telephone Directed s AVL system shares the same basic Car Com features but takes remote vehicle paging one step further by providing web enabled two way GPS vehicle location services including bread crumb tracking and geo fencing capabilities Field Disturbance Sensor An invisible dome of coverage is estab lished by the installing the 508D radar sensor Your s
7. buttons This makes it possible to assign any trans mitter button to any receiver function The transmitter initially comes programmed with Standard Configuration but may also be customized by an authorized dealer The buttons in all of the instructions in this manual correspond to a Standard Configuration transmitter standard configuration Button The arming disarming and panic function are usually controlled by this button Button Remote Controlled Chirp Muting and an optional accessory function are controlled by ne Remote Controlled Chirp Muting works by pressing 3 for less than one second before arming or disarming the system An optional accessory function such as trunk release can be controlled by pressing for 1 5 seconds This accessory output controls An optional accessory convenience or expansion function that you have added to your system can be activated by pressing EJ This accessory output controls 4 2001 directed electronics inc gt Button Another optional convenience or expansion option that you have added to your system can be activated by pressing k This accessory output controls using your system The buttons used in the instructions in this manual correspond to the standard transmitter configuration If your transmitter has been custom configured the icons on your transmitter buttons may not correspond to the indicated functions arming You can activat
8. configured with separate transmitter buttons for arming and disarming Multi Level Security Arming allows you to select which of the security system s inputs or sensors will be active and which will be bypassed at the time that the system is armed See Table of Zones section Pressing the arm button again within five seconds of arming the security system will activate the Multi Level Security Arming feature Each time the arm button is pressed again a different security level is selected The different security levels can be selected as follows gt Pressing the arm button one time The siren chirps once The system is armed 2001 directed electronics inc 7 gt Pressing the arm button a second time within five seconds The siren chirps twice followed by a long chirp Zone Two is now bypassed gt Pressing the arm button a third time within five seconds The siren chirps three times followed by a long chirp Zone Four is now bypassed gt Pressing the arm button a fourth time within five seconds The siren chirps four times followed by a long chirp Zones Two and Four are now bypassed gt Pressing the arm button a fifth time within five seconds The siren chirps five times followed by a long chirp All input zones except the ignition are now bypassed note Multi Level Security Arming only applies to a single arming cycle Once the system is disarmed and then re armed all the zones will be active again
9. the Directed Bitwriter or a personal 2001 directed electronics inc computer and the TechSoft Programmer the full triggered response can be programmed for any duration ranging from 1 to 180 seconds gt False Alarm Control Technology FACT on or off Please refer to the FACT section of this manual for a complete expla nation of how FACT operates If FACT is programmed off the security system will respond to inputs from any sensor indefinitely note Because many states have laws regulating security systems programming FACT off may cause your system to violate state laws gt Progressive door trigger on or off When the system is armed and a door is opened the system responds with ten chirps prior to beginning the full triggered sequence If an instant trigger is desired the progressive door trigger can be pro grammed off gt Valet pulse count The number of presses of the Valet switch required to disarm the security system or the VRS system can be programmed from 1 5 presses The default setting is one press Siren tones and chirp volume The output of the siren consists of six different tones in sequence Any of these tones can be eliminated by your dealer resulting in a unique easily identifiable siren sound The siren chirps can be either full volume or 6 decibels quieter than the full alarm blast 2001 directed electronics inc 21 22 The system has many options that may require extra parts
10. BILITY WHATSOEVER INCLUDING WITHOUT LIMITATION LIABILITY FOR THEFT DAMAGE AND OR VANDALISM THIS WARRANTY DOES NOT COVER LABOR COSTS FOR MAINTENANCE REMOVAL OR REIN STALLATION OF THE UNIT OR ANY CONSEQUENTIAL DAMAGES OF ANY KIND IN THE EVENT OF A CLAIM OR A DISPUTE INVOLVING DIRECTED OR ITS SUBSIDIARY THE PROPER VENUE SHALL BE SAN DIEGO COUNTY IN THE STATE OF CALIFORNIA CALIFORNIA STATE LAWS AND 2001 directed electronics inc i APPLICABLE FEDERAL LAWS SHALL APPLY AND GOVERN THE DISPUTE THE MAXIMUM RECOVERY UNDER ANY CLAIM AGAINST DIRECTED SHALL BE STRICTLY LIMITED TO THE AUTHORIZED DIRECTED DEALER S PURCHASE PRICE OF THE UNIT DIRECTED SHALL NOT BE RESPONSIBLE FOR ANY DAMAGES WHATSOEVER INCLUDING BUT NOT LIMITED TO ANY CONSEQUENTIAL DAMAGES INCIDENTAL DAMAGES DAMAGES FOR THE LOSS OF TIME LOSS OF EARNINGS COMMERCIAL LOSS LOSS OF ECONOMIC OPPORTUNITY AND THE LIKE NOTWITHSTANDING THE ABOVE THE MANUFACTURER DOES OFFER A LIMITED WARRAN TY TO REPLACE OR REPAIR THE CONTROL MODULE AS DESCRIBED ABOVE Some states do not allow limitations on how long an implied warranty will last or the exclusion or limi tation of incidental or consequential damages This warranty gives you specific legal rights and you may also have other rights that vary from State to State This product may be covered by an Anti Theft Guarantee See your authorized Directed dealer for details of the plan or call Directed Customer Service at 1 800 876 0800
11. FF Turn the ignition off Ys A No 29 2 3 Press and release the Valet switch within 10 seconds 2001 directed electronics inc 11 The LED status indicator will light steadily if you are entering Valet Mode and will turn off if you are exiting Valet Mode remote controlled valet mode The operations described in this section refer to transmitter buttons Remember the buttons used in all the instructions in this guide correspond to a Standard Configuration transmitter This may not be how your transmitter is set up 1 Open any vehicle door 2 Na 3 Press ne 4 Press again The LED status indicator will light solid if you are entering Valet Mode or will go out if you are exiting Valet Mode false alarm control technology FACT 12 Your system offers FACT a feature that prevents annoying repet itive trigger sequences due to faulty door pin switches or environmental conditions such as thunder jackhammers airport noise etc Here s how it works The alarm triggers three times Each time 88 the same sensor or switch is triggering the alarm The three trig gers are within 60 minutes of each other FACT will interpret this pattern of triggers as false alarms After the third trigger O 2001 directed electronics inc FACT ignores or bypasses that sensor or switch along with any other sensors or switches sharing the same zone for 60 minutes If the bypassed sensor tries to tri
12. Matix3 Owner s Guide mited lifetime consumer warrant Directed Electronics Inc Directed promises to the original purchaser to repair or replace with a comparable reconditioned model any Directed unit hereafter the unit excluding without limitation the siren the remote transmitters the associated sensors and accessories which proves to be defective in workmanship or material under reasonable use during the lifetime of the vehicle provided the following conditions are met the unit was professionally installed and serviced by an authorized Directed dealer the unit will be professionally reinstalled in the vehicle in which it was originally installed by an autho rized Directed dealer and the unit is returned to Directed shipping prepaid with a leg ible copy of the bill of sale or other dated proof of purchase bearing the following infor mation consumer s name telephone number and address the authorized dealers name telephone number and address complete product description including accessories the year make and model of the vehicle vehicle license number and vehicle identification number All components other than the unit including without limitation the siren the remote transmitters and the associated sensors and accessories carry a one year warranty from the date of purchase of the same This warranty is non transferable and is automat ically void if the original purchaser has not completed the warran
13. and labor A few of the options are listed below gt Progressive Unlocking In most cars with electric power door locks the system can be configured so that when disarmed only the driver s door unlocks A second press of the disarm button within 15 seconds of disarming unlocks the other doors gt Vehicle Recovery System VRS VRS is an anti carjacking device designed to help in the safe recovery of your vehicle in case of a carjacking Please refer to the Vehicle Recovery System section of this manual for a complete explanation of how the Vehicle Recovery System operates The optional VRS feature is designed to ensure that any unau thorized user of your vehicle even if using your keys and remote control will not be able to permanently separate you from your vehicle The VRS cannot prevent a carjacking attempt however it does ensure that if your vehicle is taken by an unauthorized user it will be disabled after several progressive warnings as safely as possible Should a carjacking occur the VRS allows you to concern yourself with your personal safety without worrying about your property 2001 directed electronics inc Directed has engineered this vehicle security system the fault proof starter interrupt and the VRS feature to provide the best combination of personal safety and property protection avail able When properly installed the system can never inadvertent ly stop your vehicle in traffic or on
14. asoline vehicles 2001 directed electronics inc 29 To arm using your remote You can activate or arm the system by pressing on your transmitter for one second When the system arms you will hear a short siren sound or chirp and see the parking lights flash once If the vehicle s power door locks have been connected to the system the doors will lock To disarm using your remote To disarm the system press d a You will hear two chirps and the parking lights will flash twice If power locks are connected to the system the doors will unlock If the siren chirps either four or five times when disarming see Diagnostics section This is called Tamper Alert Arming while driving Press on your transmitter while the vehicle is running The system will chirp once and then once more to indicate that the ignition is on Disarming without a transmitter Turn on the ignition Press the Valet switch the programmed number of times within 15 seconds The system should now disarm If it does not you may have waited too long Turn the ignition off and on and try again To enter or exit Valet Mode Turn ignition to run position then turn to off position Press and release the Valet switch within 10 seconds The LED status indicator will light solid if you are entering Valet Mode and it will go out if you are exiting Valet Mode To activate Panic Mode Press and hold down for 1 5 seconds To exit Panic Mo
15. d without opening a door so that the doors will automatically lock when the system passively rearms gt Arming disarming confirmation siren chirps on or off gt Auto Lock Auto Unlock on or off With this feature on the doors will lock three seconds after the ignition is turned on and unlock when the ignition is turned off The system will prevent the doors from locking when the ignition is turned on with any door open If your installer is programming the secu rity system with the Directed Bitwriter or a personal computer and the TechSoft Programmer ignition lock and unlock are independent features and can be programmed separately Passive door locking with passive arming or active door locking only when arming with the transmitter Passive locking allows the vehicle s doors to lock when the security system passively arms after the 30 second countdown This feature only works if passive arming has been programmed Panic mode enabled disabled with the ignition on Some states have laws against siren capability in a moving vehicle gt Forced passive arming on or off If your system is programmed for passive arming and the forced passive arming feature has been programmed on the system will passively arm after one hour even if a protected entry has been left open This feature is useful if a door has been left ajar when leaving the vehicle Forced passive arming ensures that the security system will be armed in every sit
16. de gt Press g A on the transmitter To activate Remote Controlled Chirp Muting gt Press briefly before arming or disarming and the confirmation chirp s will be eliminated for that one operation only Location of Valet Switch Number of Valet switch pulses for disarming 30 2001 directed electronics inc Cut along dotted line and fold for a quick and easy reference to keep in your purse or wallet The company behind this system is Directed Electronics Inc Since its inception Directed has had one purpose to provide consumers with the finest vehicle security and car stereo products and accessories available The recipient of nearly 100 patents and Innovations Awards in the field of advanced electronic technology Directed is ISO 9001 registered Quality Directed Electronics products are sold and serviced throughout North America and around the world Call 800 274 0200 for more information about our products and services O O 8 4 O 1 Directed is committed to delivering world class quality products and services that excite and delight our customers DA 2222 22 4 ELECTRONICS INC Vista CA 92083 www directed com 2001 Directed Electronics Inc All rights reserved G909449 8 01
17. disarm VRS and Valet Mode 2001 directed electronics inc 17 power saver mode Your system will automatically enter Power Saver Mode while armed or in Valet Mode after a period of time in which no oper ation has been performed This lowers the current draw to prevent the system from draining the vehicles battery Power Saver Mode takes over under the following conditions Power Saver when the system is armed After the system has been armed for 24 hours the LED will flash at half its normal rate decreasing the system s current draw gt Power Saver in Valet Mode When the system enters Valet Mode the LED illuminates steadily If the vehicle is not used ignition is not turned on for a period of one hour while the system is in Valet Mode the LED will shut off If the system remains in Valet Mode the LED will come back on the next time the ignition is turned on and then back off j 18 Programming options control what your system does during normal operation and require few or no additional parts However some may require additional installation labor The following is a list of the program settings with the factory settings in bold gt Active arming only with the transmitter or passive arming automatic arming 30 seconds after the last door is closed 2001 directed electronics inc If programmed for passive arming a feature called Smart Relocking will occur when the system is disarme
18. door or a switch protected trunk or hood is open the system will not passively arm unless forced passive arming is programmed on See Programming Options section of this guide Additionally each time a sensor is triggered during the arming countdown the 30 second countdown starts over When armed your vehicle is protected as follows gt Light impacts will trigger the Warning Zone signal When triggered the siren will chirp and the parking lights will flash for a few seconds gt Heavy impacts will trigger the system The triggered sequence is between 1 180 seconds of constant siren and flashing parking lights Ifa vehicle door is opened the security system will immedi ately start chirping the siren and flashing the parking lights 2001 directed electronics inc Three seconds later the siren output changes to a continuous blast This progressive response gives you time to disarm the security system with your transmitter if you inadvertently open the door while the system is armed while still providing an instant response even if the door is immediate ly closed gt Turning on the ignition key will trip the same two stage response as opening a door The optional starter interrupt prevents the vehicle s starter from cranking multi level security arming optional feature note Multi Level Security Arming is only available when using an optional 4 button Radar Master transmitter that has been
19. e or arm the system by pressing gfV on your transmitter for one second When the system arms you will hear a short siren sound or chirp and see the parking lights flash once If the vehicles power door locks have been connected to the system the doors will lock While the system is armed the LED status indicator will flash approximately once per second indicating that the system is actively protecting your vehicle If you hear a second chirp after arming and see the LED status indicator flashing in groups refer to the Diagnostics section of this guide This extra chirp is called Bypass Notification 2001 directed electronics inc 5 The system also can be programmed to arm itself automatically called passive arming If the system is programmed for passive arming it will automatically arm 30 seconds after the ignition is turned off and the system sees you leave the vehicle by opening and closing a door Whenever the system is in its 30 second passive arming countdown the LED status indicator will flash twice as fast as it does when the system is armed The siren will chirp once 20 seconds after the last door has been closed The system is not actually armed at that point The system arms and the doors lock if connected and programmed for passive locking at 30 seconds but the siren will not chirp The early chirp provides you with a 10 second warning prior to arming note If any protected entry point such as a
20. ecurity system can then react to any intrusions into this field with the triggered sequence 2001 directed electronics inc Headlight and Parking Light Automation The NiteVision system will automatically turn on your parking and headlights when it gets dark In addition NiteVision will turn your headlights on whenever the windshield wipers are used A transmitter function can also be used to turn on your parking and headlights for a programmed time Power Trunk Release The channel two output of the system can operate a factory power release for the vehicle s trunk or hatch An optional relay may be required If the factory release is not power activated the Directed s 522T trunk release solenoid can often be added Power Window Control Automatic power window control is pro vided with the 529T and 530T systems Radar Master Remote The 4 button 16 channel Radar Master remote allows the security system s Multi Level Security Arming feature to be accessed when the transmitter buttons are configured with separate transmitter buttons for arming and disarming Valet Start System For the ultimate in convenience the Valet start system can start your vehicle monitor engine functions and power your climate control system with a push of a button Over rev protection open hood lockout brake pedal shutoff and automatic timer shutoff are all included This feature is only for automatic transmission fuel injected g
21. gger the system while it is being bypassed the 60 minute bypass period will start over This ensures that a sensor that continually triggers will remain bypassed Doors are covered by FACT differently If the alarm is triggered by an open door for three full cycles the doors will be bypassed until the trigger ceases note Arming and disarming the system does not reset this function The only ways to reset a bypassed zone are for it to not trigger for 60 minutes or to turn on the igni tion If testing your system it is important to remember that the FACT programming can cause zones to be bypassed and appear to stop working If five chirps are heard when disarming FACT has been engaged If you wish to clear the FACT memory turn the ignition key on FACT is programmable See the Programming Options section of this guide The microprocessor at the heart of your security system is constantly monitoring all of the switches and sensors that are connected to it It detects any faulty switches and sensors and prevents them from disabling the entire system The micropro 2001 directed electronics inc 13 cessor will also record and report any triggers that occurred during your absence arming diagnostics If the system is armed while an input is active door open sensor triggering etc the unit will chirp once when arming and then one more time a few seconds later This is called Bypass Notification note
22. ion may require additional labor Input A physical connection to the system An input can be provided by a sensor pinswitch or through an existing system in the vehicle such as ignition or courtesy lights LED Red light mounted somewhere in the vehicle It is used to indicate the status of your system It is also used to report trig gers and faults in the system or sensors O 2001 directed electronics inc Shock Sensor This is a sensor mounted in the vehicle that is designed to pick up impacts to the vehicle or glass Siren Noise generating device usually installed in the engine compartment of the vehicle It is responsible for generating the chirps you hear as well as the six tones you hear while the alarm is triggered Transmitter Hand held remote control which operates the various functions of your system Trigger or Triggered Sequence This is what happens when the alarm goes off or trips The triggered response of your system consists of 30 seconds of siren sounding and parking light flashing Valet Switch A small push button switch mounted somewhere inside the vehicle It is used to override the alarm when a trans mitter is lost or damaged or to enter or exit Valet mode Warning Zone Response Lighter impacts to the vehicle will generate the secondary Warning Zone response It consists of several seconds of siren chirps and parking light flashes Zone A zone is a separate input that the
23. l ias di on 1er as Caw a deals Dedo 17 Power Saver Mode 18 Programming Options sa 4g ca no 64c 46 3 40 6 one ae oad coe rte 18 Installation OPUS e sproribrorpar reirte rro apo tas 22 Vehicle Recovery System VRS ooooococcccoccococo eens 22 Ano me VRS eera a E soi E 23 VRS Ingpered Sequence saarra dian iad dada dada ta aa 24 Diarange the VES ncn trases raptada boned oon chen 25 Glossary OF lenis ers oben es tae 002929006 c c 26 Security amp Convenience Expansions 28 Quick Reference Guide Removable 30 2001 directed electronics inc 1 heat de orkid A 3 channel control module A pair of four button transmitters An XHF receiver antenna A shock sensor A siren A red LED status indicator light A push button Valet switch Your warranty registration Y Y Y Y Y Y VV Y Fault proof starter interrupt ready circuitry may require additional labor Congratulations on the purchase of your state of the art vehicle security system It has been designed to provide years of trouble free operation This system must be installed by an authorized dealer Installation of this product by anyone other than an authorized dealer voids the warranty As verification of authorization all authorized dealers are provided with preprinted dealer certificates In order to maximize the use of this system please review this o
24. ncy 16 Your system transmits and receives at 433 MHz This provides a cleaner spectrum with less interference and a more stable signal Enjoy a phenomenal increase in range even in areas with high radio interference 2001 directed electronics inc gt Owner Recognition is a feature available exclusively from Directed Using a Directed Bitwriter hand held programming tool your dealer can program many of the system settings The programmer makes it possible to program different settings for each transmitter that is used with the system Then whenever a specific transmitter is used the system will recall the settings assigned to that transmitter Owner Recognition lets up to four users of the system have different settings that meet their specific needs It is almost like having four separate alarms in your vehicle one for each user note Owner Recognition cannot be programmed without a Bitwriter and the necessary software Check with your dealer for more information smart powerup ll This security system will store its current state to non volatile memory If power is lost and then reconnected the system will recall the stored state from memory This means if the unit is in Valet Mode and the battery is disconnected for any reason such as servicing the car when the battery is reconnected the unit will still be in Valet Mode This applies to all states of the system including arm
25. nt trigger often used for hood trunk pinswitches 2 Instant trigger a heavier impact detected by the shock sensor 3 Door switch trigger 4 Instant trigger for optional sensors gt Ignition trigger If the Warning Zone response is triggered the LED will not report It note Your system stores the last two triggered zones in memory If your system has been triggered but the LED has been reset by turning on the ignition your dealer can still recall the last two zones that were triggered Contact your dealer for details 2001 directed electronics inc 15 This unit features Anti Code Grabbing ACG with Random Code Encryption This means the receiver and transmitters each use a mathematical formula called an algorithm to change their code each time the transmitter is used This technology has been developed to increase the security of the unit The control unit knows what the next codes should be This helps to keep the transmitter in sync with the control unit even if you use the remote control out of range of the vehicle However if a trans mitter button has been pressed many times out of range of the vehicle or the battery has been removed it may get out of sync with the control unit and fail to operate the system To re sync the remote control simply press of the transmitter several times within range of the vehicle The alarm will automatically re sync and respond to the transmitters normally high freque
26. perating the vehicle and not disarmed prior to leaving the vehicle it is still armed and will trigger the next time the vehicle is driven VRS triggered sequence 24 Fifteen seconds after the last door has closed the system s LED status indicator will begin flashing This delay is intended to allow you time to distance yourself from your vehicle in the event of a carjacking Forty five seconds later the siren begins chirping and the park ing lights begin flashing This time could be used to notify au thorities that your vehicle has been hijacked and tell them what the VRS will do next Fifteen seconds after the siren chirps begin the siren s output will change to a continuous blast From this point forward when the ignition key is turned off the VRS will immediately turn on the starter interrupt This will prevent the vehicle from being restarted thus immobilizing it at that spot 2001 directed electronics inc Three minutes after the constant siren output begins the flashing parking lights and the siren will stop The starter interrupt will remain active until the system is disarmed If the door is opened or the ignition is turned off and on in an attempt to restart the car the siren and light flashing will begin again disarming the VRS Take the time to familiarize yourself with the VRS triggering se quence and the disarm procedure It is important to recognize and identify the VRS trigger seq
27. railroad tracks while the vehicle is in operation It is unlike other systems that shut down your engine while it is running This system is designed to per form starter interrupt The starter interrupt cannot shut down an already running engine it can only prevent an engine from starting in the first place Any installation which allows this product to shut down a vehicle s engine when it is running is contrary to the product s design and intended usage and Directed hereby expressly dis claims any liability resulting therefrom arming the VRS To arm the VRS turn the ignition to the ON position and press the arm button on the remote transmitter for one second The parking lights will flash and the siren will chirp once This can be done before driving or while driving the vehicle Once the system is armed it will initiate its triggered sequence see the following section if any door is opened and closed If you are forced from the vehicle the system will trigger as the door is opened and closed This is how the system works to combat intersection carjacking 2001 directed electronics inc 23 To protect against parking lot carjacking arm the VRS before leaving the vehicle The system will now trigger automatically the next time you or anyone drives the vehicle This helps to protect the vehicle if someone takes your keys and remote trans mitter by force in a parking lot note If the VRS system is armed while o
28. ty i What Is Included 2 Important Infomation esir ernia e 8602 209 L A9 calada air ridad 2 2 tETTI 11111611011 CE s se ne 6g 6 8 v c SE 5 d0 l s ho se nes oeeeec en secen cede 3 TOUR TT ua fence ceed Cow ou ha ets Wace Koa ae a 3 LOCOS cross rota ei a oe 3 Transmitter Functions o 4 Sundatd Contisuratio esoo eya rios dsd tw and yolk ar 4 Using Your SYSTEM sacras iaa e de kes das 5 ADDE sopresa pts dd gi Giietdug u t edg yr AAA 5 Multi Level Security Arming Optional Feature E Amine While DIVNE renta cop n crea 8 y AA ee ee ee eee ee ee ee eee 9 Sikem on l 4 00720901601010 E E 2 c t i go c2 9 Disarmine Without a Transmitter ersi recreen creaue y eRe ed ences 10 Remote Controlled Chins Maine sac se hie 4 n ch t B un l heoretorenn edd 10 Pnie AAA 11 Viet Mode seriessimreedieke ta bap eee eee ee eS 11 Remote Controlled Valet Mode 12 False Alarm Control Technology FACT 12 A 13 Amme Danno N Un 94090 ray belay oan eee ee 14 Disarming Diagnostics se sses 250d s eed Reeder enews een SOA 14 Tae OFZ ONS i2 oa a oboe he de hS oREME OO EYE Odd Rw ees 15 Anti Code Grabbing ACG 16 High Frequency ori dota cool Genes did 16 Owner Kecoonition door ir rad toos 17 Smart Power Upi
29. ty card and mailed it within ten 10 days of the date of purchase to the address listed on the card the unit s date code or serial number is defaced missing or altered the unit has been modified or used in a manner contrary to its intended purpose the unit has been damaged by acci dent unreasonable use neglect improper service installation or other causes not arising out of defects in materials or construction The warranty does not cover damage to the unit caused by installation or removal of the unit Directed in its sole discretion will determine what constitutes excessive damage and may refuse the return of any unit with excessive damage TO THE MAXIMUM EXTENT ALLOWED BY LAW ALL WARRANTIES INCLUD ING BUT NOT LIMITED TO EXPRESS WARRANTY IMPLIED WARRANTY WARRANTY OF MER CHANTABILITY FITNESS FOR PARTICULAR PURPOSE AND WARRANTY OF NON INFRINGE MENT OF INTELLECTUAL PROPERTY ARE EXPRESSLY EXCLUDED AND DIRECTED NEITHER ASSUMES NOR AUTHORIZES ANY PERSON OR ENTITY TO ASSUME FOR IT ANY DUTY OBLIG ATION OR LIABILITY IN CONNECTION WITH ITS PRODUCTS DIRECTED DISCLAIMS AND HAS ABSOLUTELY NO LIABILITY FOR ANY AND ALL ACTS OF THIRD PARTIES INCLUDING ITS AUTHORIZED DEALERS OR INSTALLERS DIRECTED SECURITY SYSTEMS INCLUDING THIS UNIT ARE DETERRENTS AGAINST POSSIBLE THEFT DIRECTED IS NOT OFFERING A GUAR ANTEE OR INSURANCE AGAINST VANDALISM DAMAGE OR THEFT OF THE AUTOMOBILE ITS PARTS OR CONTENTS AND HEREBY EXPRESSLY DISCLAIMS ANY LIA
30. uation 2001 directed electronics inc 19 note When the system passively arms after one hour the entry point that has been left open and anything con nected to the same zone is bypassed and cannot trigger the system However the remaining inputs to the system are fully operational gt Automatic Engine Disable AED on or off The purpose of this feature is to protect the vehicle from being stolen at all times regardless of whether or not the alarm is armed If AED is programmed on the starter of the vehicle will be dis abled 30 seconds after the ignition is turned off Once the key is turned off the LED will flash slowly one half its normal armed rate to indicate the AED arming cycle Thirty seconds later the starter of the vehicle will be dis abled To start the car it will be necessary to arm the car with the remote and then disarm it with the remote It is also possible to disarm the AED feature by turning the ignition key to the run position and pressing the Valet switch the programmed number of times AED is disabled when the system is in Valet Mode note This feature will only function if the starter inter rupt relay has been installed gt Full trigger response 30 or 60 seconds This determines how long the full triggered sequence lasts Some states have laws regulating how long a security system can sound before it is considered a nuisance If your installer is programming the security system with
31. uence and know how to disarm it in case of accidental activation Once the VRS is armed it does not disarm automatically You must disarm it the next time you operate the vehicle You must disarm it with one of the following procedures If the system has not entered the triggered sequence siren has not started chirping s 1 Turn the ignition on 2 Press the disarm button for one v2 oun second The lights will flash and the siren will chirp twice S If the system has entered the triggered sequence the siren has begun chirping pressing the disarm button of the transmitter will not disarm the VRS To disarm the VRS during a VRS trigger sequence 2001 directed electronics inc 25 SAS 1 Turn the ignition on gt 2 Press the Valet switch the pre v2 DRW 94 programmed number of times to disarm the VRS system glossary of terms 26 Control Unit The brain of your system Usually hidden underneath the dash of the vehicle It houses the microprocessor which monitors your vehicle and controls all of the system s functions Fault Proof Starter Interrupt An automatic switch controlled by the security system which prevents the vehicle s starter from cranking whenever the system is armed The vehicle is never prevented from cranking when the system is disarmed in Valet mode or should the starter interrupt switch itself fail Your system is ready for this feature however installat
32. wner s guide carefully prior to using your system You can print additional or replacement copies of this owners guide by accessing the Clifford website at www clifford com 2 2001 directed electronics inc system maintenance The system requires no specific maintenance Your remote control is powered by a small lightweight 3 volt lithium battery that will last approximately one year under normal use When the battery weakens operating range will be reduced and the LED on the remote will dim your warranty Your warranty registration must be completely filled out and returned within 10 days of purchase Your product warranty will not be validated if your warranty registration is not returned Make sure you receive the warranty registration from your dealer It is also necessary to keep your proof of purchase which reflects that the product was installed by an authorized dealer fcc id notice This device complies with Part 15 of FCC rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 This device must accept any interference received including interference that may cause undesired operation Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate this device 2001 directed electronics inc 3 y ji f The receiver uses computer based code learning to learn the transmitter
Download Pdf Manuals
Related Search