Z-Wave AC Motor Controller.indd
Contents
1. Technical Specifications RF Protocol Z Wave MultiChanel Command Class Connections type See wiring above Manual Switch compatibility Bell Press type buttons or two buttons with neutral position switch Operating Voltage AC 240V 50Hz MaxLoading 6A 1 8 HP 240V AC motor Switch type Universal relay RF Frequency Operation Range Application Operation temperature Storage temperature 10 80 C 921 42Mhz AU NZ approved RF for Z Wave Up to 30m when no obstacles Indoor use only 0 55 C Weight 70g Housing ABS Dimensions LxWxH 48mm x 45mm x 18 mm Compliance AS NZS 4268 2008 AS NZS CISPR 14 1 IEC60669 2 1 RCM N5496 Supporting Z Wave Command Classes Basic Class Slave with routing capabilities Generic Class Multilevel Switch Specific Class Motor Control Class C class 0x27 COMMAND_CLASS_AII_ Switch class 0x8E COMMAND_CLASS_Multi_Channel_Association class 0x70 COMMAND_CLASS_ Configuration class 0x72 COMMAND_CLASS_Manufacturer_Specific class 0x75 COMMAND_CLASS_ Protection class 0x77 COMMAND_CLASS_Node_Naming_and_Location class 0x86 COMMAND_ CLASS Version class 0xX25 COMMAND_CLASS_Binary_Switch class 0x20 COMMAND_CLASS _ Basic class 0x26 COMMAND_CLASS_ Multilevel_ Switch class 0x87 COMMAND_CLASS _ Indicator class 0x85 COMMAND_CLASS_ Association class 0x2B COMMAND_CLASS_Scene_Activation class 0x2C COMMAND_CLASS_Scene_Actuator_Configuration Configuration Parameters Parameter No 1 Size 12. Default 3 Name Buttons mode Description One push button One button is used chose any press while moving up and down stops while stopped moves to opposite direction to previous Two buttons with neutral position Up click moves up if stopped and stops if moving down Down click moves down if stopped and stops if moving up Hold Up Down moves in up down Release stops Two toggle switch Switch to Up Down moves up down Two paddles with Power and Direction Hold Up button to move blinds up If Down button is pressed blinds will move down Release Up button to stop Type rangemapped Values 0 gt One push button 1 gt Two paddles with Power and Direction 2 gt Two toggle switch 3 gt Two buttons with neutral position Parameter No 2 Size 2 Default 0 Name Automatically close after Description If not zero automatically close blind after a user defined time Type range Values 0 gt Disabled 1 1 gt sec Parameter No 3 Size 1 Default 0 Name What to do on RF close command Description Defines how to interpret RF Off command Can be used in conjunction with Auto Close function Ignore to open the door by motion detectors and close it back after some amount of time in case of multiple motion detectors each would try to open that would break logics Open to open on both On and Off paddle press on the remote and close after some amount of time Button close click will still work if button operations
3. are not disabled Note that Dim Down command will still begin close motion Type rangemapped Values 0 gt Close 1 gt Ignore 2 gt Open 3 gt Open if closed otherwise Close Parameter No 4 Size 1 Default 50 Name Typical click timeout Description Typical time used to differentiate click hold double and triple clicks Type range Values 1 100 gt in 10ms units Parameter No 5 Size 1 Default 0 Name Invert buttons Description Type rangemapped Values 0 gt No 1 gt Yes Parameter No 6 Size 1 Default 1 Name Action on button press or hold Description Defines which command should be sent to Association group on button press or hold Scene mode will send 1 for Up event 2 for Stop 3 for Down Type rangemapped Values 1 gt Switch On Off and dim using Basic Set and MultiLevel Start Stop Changing 2 gt Send Scene Parameter No 7 Size 1 Default 1 Name LED mode Description Set LED indication mode Type rangemapped Values 0 gt Disabled 1 gt Show working state 2 gt Always on 3 gt Show opened state 4 gt Indicator Command Class Parameter No 10 Size 1 Default 60 Name Full close time Description Time to go from opened to closed state Used to estimate the current level Note that in Permanent motion mode the reported value would be Closed or Opened while all Basic and Multilevel Set values 1 99 255 would Open except 0 value that would Close T
4. to enable the protection Description Defines which command from blocking device to interpret as closed door and hence unpro tected Type rangemapped Values 0 gt on On 1 gt on Off Parameter No 14 Size1 Default 0 Name Invert open and close relays Description Allow exchanging open and close relays if blind control is wired to the motor incorrectly Type rangemapped Values 0 gt No 1 gt Yes Association Groups Group Number Max Nodes Description 1 10 Click press and hold of up down buttons 2 10 Send Reports on blind state change Configuration Reset The Shutter Controller supports a configuration resets function Configuration reset means All configuration values are defaulted This function can be activated by sending a configuration set frame SAFETY INSTRUCTIONS Always read the safety instructions carefully Keep this User s Manual for future reference Keep this equipment away from high humidity and any liquid This product is for indoor use only inside dry wall cavity or similar environment Keep e nough space around for ventilation Do not connect to the load bigger then maximum approved for this product Do not connect to the non compatible load If the product s enclosure is damaged it shall be replaced by the manufacturer or its ser vice agent or similarly qualified person in order to avoid a hazard DO NOT INSTALL THIS DEVICE INSIDE SEALED INCLOSURES AND METAL BOXES ALWAYS
5. LEAVE ROOM FOR VENTILATION INSTALLATION MUST BE DONE BY CERTIFIED ELECTRICIAN Specifications are subject to change without further notice The information in this document is subject to change without notice Digital Home Systems Pty Ltd DHS does not make any representations or warranties implied or otherwise regarding the accuracy and completeness of this document and shall in no event be liable for any loss of profit or any commercial damage including but not limited to special incidental consequential or other damage TRADEMARKS All trademarks and registered trademarks are the property of their respective owners or companies DHS One 1 Year Limited Warranty Digital Home Systems Pty Ltd warrants this DHS branded hardware product against defects in materials and workmanship under normal use for period of one 1 year from the date of retails purchase by the original enduser purchaser Warranty Period PLEASE NOTE breaking security label will void the warranty Terms and conditions To see complete terms and conditions browse to http www digitalhomesystems com au images stories DHS_Terms_and_conditions pdf Product of Digital Home Systems Pty Ltd See all range of compatible devices at www digitalhomesystems com au Enquiries Sales and Marketing Email office dhsys com au 2012 Digital Home Systems Pty Ltd All rights reserved
6. allation 1 Turn power OFF by switching off the Main circuit breaker and test that power is OFF before wiring 2 Ensure Shutter Controller capacity matches the load requirements 3 Wall Installation Connect it with your external switch default is two buttons with neutral position switch Please see Wiring Diagrams amp Configuration Parameters You can use 2 Gang Clipsal Wall Plate with two push buttons 4 Re apply power to the Main circuit breaker to test the system carefully if the indicator light on Shutter Controller blinks 30 seconds and then keep breathing it means the installation is done in right way 5 Turn OFF the power again 6 Shutter Controller is in wall device Please secure it behind wall plate with push buttons Please be careful not to pinch or crush wires Reapply power to the circuit at Main circuit breaker Manual Operations Press and release the buttons on the connected push buttons to turn UP DOWN the connected motor It is recommended that you wire your Shutter Controller and include it into Z Wave network before mount ing it in a wall cavity Leigh of wires between manual button and device must be less than 0 5m Please note in Australia and New Zealand the installation must be done by certified electrician Please note Buttons on the wall plate have to be Bell Press type e g push button Saturn Series 6OPBBP or similar Please note Please check the maximum load before installing or operating P
7. lease note 6A external fuse before the Shutter Controller must be installed in line to protect against overload Maximum load 250V a c 50Hz 1 8HP PUSH BUTTON Z Wave Operations Before including the product to your Z wave network it is advised to perform removal procedure to reset network settings The Z Wave Shutter Controller must be included into your Z Wave home network before it can send and receive Z Wave commands The Z Wave Shutter Controller can only communicate to devices within the same Z wave home network Always follow your controller s specific instructions for Z Wave inclusion exclusion association and control opera tions Exclusion from Z wave home network general instructions 1 Install Connect the Z Wave Shutter Controller to the load power circuits and to the manual switch as per in structions in the section INSTALLATION above 2 Start exclusion procedure on your controller and when requested 3 times quickly press and release a button on the connected manual Press Button switch During the whole procedure the controller and Z Wave Shutter Controller must be close proximity of not more then 15cm 3 Successful exclusion will be indicated by your Z Wave LED on the Z Wave Shutter Controller will start slow blinking In case exclusion was not successful try the procedure again remote controller Inclusion to Z wave home network general instructions 1 Connect the Z Wave Shutter Controller to the
8. motor power circuits and to the manual switches as per instructions in the section INSTALLATION above 2 Make sure your Z Wave Gateway is in the correct operating mode inclusion To include quickly press and release 3 times a button on the connected manual Press Button switch During the whole procedure controller Gateway and Z Wave Shutter Controller must be in close proximity of 15cm Successful inclusion will be indicated by your Z Wave remote controller Gateway In case inclusion was not successful try the procedure again or reset network settings by running exclusion procedure see below 3 Once the Z Wave Shutter Controller has been added into your Z Wave home network successfully you may need to assign it to a specific button on your controller Gateway Refer to your Z Wave controller Gateway panel for instructions on how to do this 4 Now you can control your lamp via your Z Wave Gateway or other controller Indication modes The indicator gives various statuses of the device as follows 1 Automatically add blinks 30 seconds 2 Ready for learn mode Indicator light Breathing 3 Learn in progress add Indicator light blinks 1 time 4 Learn in progress remove Indicator light blinks 1 second 8 times 5 Learn mode success Indicator light is on for 1 time and then if load is on indicator light keep on if load is off indicator light keep breathing 6 Learn mode failed Indicator light blinks fast
9. p Works with MI CASA VERDE VERA D IG TAG OME NEVO I STEALS AEON LABS mControl ADT Pulse Z Wave AC Motor Shutter Controller User Guide DHS ZW TMC 01 Z Wave Technology for Automated Homes Z Wave is a state of the art wireless technology used as a standard for wireless home control It is a next generation wireless ecosystem that lets all your home lighting systems and electronics talk to each other and to you via a controller or a gateway It uses simple reliable low power radio waves that easily travel through walls floors and cabinets All products in Australian New Zealand version 921 4h MHz featuring the Z Wave logo are certified to work smoothly with each other Product Overview The DHS Z Wave AC Motor Shutter Controller DHS ZW TMC 01 is Z Wave Shutter device specifically designed for use in smart homes and offices The product allows to operate roller blinds shutters wirelessly using a Z wave enabled AUS NZ version 921 42 MHz controllers compatible universal remote controllers control panels gateways PC with Z Wave USB dongle or Manually via connected manual switch The shutter controller can act as a wireless repeater to ensure that commands intended for another device in the network are received This is useful to eliminate RF deadspots when the radio range of the Z Wave network is influ enced This function is part of the Z Wave network functionality and is set up via Z Wave controller Inst
10. ype range Values 0 gt Keep in permanent motion 1 1 gt seconds Parameter No 11 Size 1 Default 60 Name Full open time Description Time to go from closed to open state This value may differ from full close time for some blinds due to gravity Used to estimate the current level Note that in Permanent motion mode the reported value would be Closed or Opened while all Basic and Multilevel Set values 1 99 255 would Open except 0 value that would Close Type range Values 0 gt Keep in permanent motion 1 1 gt seconds Parameter No 11 Size 1 Default 60 Name Full open time Description Time to go from closed to open state This value may differ from full close time for some blinds due to gravity Used to estimate the current level Note that in Permanent motion mode the reported value would be Closed or Opened while all Basic and Multilevel Set values 1 99 255 would Open except 0 value that would Close Type range Values 0 gt Keep in permanent motion 1 1 gt seconds Parameter No 12 Size 1 Default 0 Name Node Id of the blocking device Description Id of the device which commands would be interpreted not as Open Close but as block unblock Useful with door opening detector if the door is open block the blind not to break shades while they move Type range Values 0 gt Disabled 1 24 gt Node Id Parameter No 13 Size1 Default 0 Name On which command from blocking node
Download Pdf Manuals
Related Search