Acrylic Sinks
Contents
1. if Caulk sure the rim of your new sink rests on your countertop If you need to adjust the hole size usea a Caulk Counter Top Si in Mounting Tab are not required As a reference please see cut out dimensions on next page for your product aie ee in Cut out the countertop on this new line Trial fit your sink into the hole making sure it is centered where you want it FIGURE 1 Attach sink to countertop as shown Remove sink Use a good grade of silicone caulk adhesive and apply a bead under the lip of the sink then replace the sink in the hole Attach sink to countertop with bolts and clips provided see below Hand tighten bolts only with three rotations Fig 1 IMPORTANT Do not over tighten bolts Sink will damage if bolts are over tightened Note It s not necessary for the bolts and clips to be installed Their primary purpose is to hold the sink in place while the adhesive dries If there isn t clearance for them follow steps 1 7 and fill sink with water to hold in place while adhesive dries To finish the job fill any variances between counter top and sink by sealing outside of sink with a good grade of color matched or clear silicone caulk adhesive When installing drain to sink make sure to use a high grade silicone caulk or latex Do not use pl2. 22 22 __ KSENVxx er 13 x 10 25 XX 17 5 x 12 25 BARxx LTxx LTBxx 15 x 15 x 6 5 20 x 22 20 5 22 m 29 25 3 4 25 a gt 7 lt ET cae 15 1 4 15 1 4 _ _ 15 1 2 19 2 KSxxH KSxxHA KN 23 2 he 13 x 15 25 13 25 15 25 KSUxxA KSUxxKB KSxxCS 29 x 15 5 25 75 19 25 22 DO YOU HAVE Tape measure Pencil Safety glasses Caulk gun Caulk color matched or clear Saber saw or keyhole saw IMPORTANT Before you begin determine appropriate product reference above Read installation instructions carefully before starting project Keep instructions for warranty information Do not use plumber s putty May result in product failure Use a high grade silicone caulk or latex for all necessary locations INSTALLATION INSTRUCTIONS REPLACING YOUR OLD SINK No cutting of your existing countertop is necessary Simply place the sink in the hole and make saber saw or keyhole saw then continue with the instructions below MOUNTING SINK IN A NEW COUNTERTOP Place the sink upside down on the countertop in the desired location With a pencil trace a line around the outside edge of the sink onto the countertop Remove sink from the countertop Measure in 7 8 and draw new lines inside the first sink outline just drawn Radius corners
3. Acrylic Sinks 33 31 33 The finishing touch 4 O 0O ras C 0000 2 7 KSxxDX KSxxGC KSxxHL KSxxID KSxxLX KSxxZ KSxxC KSxxCB KSxxJ KSxxIN KSxxLD KSxxP KSxxTE 317 20 5 KSxxQ KSxxR KSxxSB3 17 KSxxVE KSxxY 337 19 Q 33 x 22 ri 2 25 7 8 28 27 KSxxA KSxxAB D 29 x 17 S7 N 4 11 21 3 8 O O 17 1 2 26 1 2 ko Ne JX 3 25 2 2 2 KSxxW is A 5 KSxxN 5 5 27 16 2 25 875 x 21 375 28 17 5 J 2 25 24 1 2 25 KSxxB 0000 0000 26 5 15 N a 7 N 5 A FAA 9102 ie Ne A 2 KSxxMD KSxxM KSxxE KSxxEE ee 17 25 19 5 24 5 16 KSxxX 25 22 16 15 16 20 LAVxx19 L 19 5 x 17 KSxxV 32 4 32 16 207 20 20 A O O
4. INK TEMPLATE DIMENSIONS 20 1 4 L KSxxDX KSxxGC KSxxHL KSxxID KSxxIN KSxxLD KSxxP KSxxTE KSxxVE KSxxY 241 8 19 5 8 L KSxxK 23 KSxxE KSxxEE 17 3 4 ae J 18 3 4 17 1 4 L L KSxxLX KSxxZ KSxxC KSxxCB KSxxJ KSxxQ KSxxR 5 583 25 1 4 7 26 1 4 15 3 4 14 1 4 L L KSxxN KSxxS 223 4 J T J 14 1 4 20 1 4 L L KSxxMD KSxxM KSxxW KSxxX 1144 risa 17 3 4 15 1 4 E 7 lt H gt lt H 15 1 4 KSxxV 18 1 4 13 1 4 15 1 4 12 1 4 KPREPxx KSxxSQ2 LAVxx19 LAVxx17 18 1 4 18 3 4 Ee i 8 1 2 10 1 2 13 1 4 20 1 4 20 1 4 KSENVxx LAVxx15 BARxx LTxx LTBxx 1 1 1 4 H 1 1102 27 1 4 22 3 4 15 1 4 R2 5 8 2 5 8 8 2 5 8 13 1 2 13 1 2 20 1 8 19 1 8 1 R2 5 8 R2 5 8 R2 5 8 R2 5 8 KSxxH KSxxHA KSUxxA KSUxxKB 1 19 3 4 1 3 4 R2 5 8 R2 5 8 30 3 4 KSxxCS 17 7 16 KSxxVE Undermount WARRANTY INFORMATION Please fill out and return to LYONS INDUSTRIES INC 30000 M 62 WEST Dowagiac MI 49047 Name Name of Store Purchased From Street Address Date of Purchase City State Zip Location of Store City State Phone Signature Date SCRATCH REMOVAL I
5. NSTRUCTIONS 1 For effective scratch removal and polishing you will need to purchase these items i e SUPERFICIAL SCRATCH 1 sheet 1000 grit 3M wet dry sandpaper 2000 grit 1 sheet 1500 grit wet dry sandpaper 1 sheet 2000 grit 3M wet dry sandpaper 1 small container of 3M rubbing compound 05933 These items can be purchased at most auto supply stores that provide supplies to professional paint and body shops Call before you go LIGHT SCRATCH Not all auto supply stores will have these items 1500 2000 grit Start sanding with 2000 grit paper Use small squares of paper about 2 x 2 for all sanding and use lots of water The water serves as both lubricant and to prevent residue buildup on the paper Residue buildup shortens the effective life of the paper and may scratch the surface you re trying topolish w 2000 grit paper is the finest grit available the higher the number the finer the grit If you can t remove all of the scratches with 2000 grit switch to 1500 grit Remember to wash the paper frequently with water as you sand 4 Ifall of the scratches can t be removed with 1500 grit switch to 1000 grit This should remove most fine scratches If you have deep scratches or a gouge coarser paper may have to be used see chart to right Be careful Using grit that is too coarse may actually put in more scratches than it removes DEEP GOUGE Once you have removed all of the scratches by sanding with the fines
6. nge of a defective unit The exchange of a unit will be limited to supplying a replacement unit or component part of comparable size and style and does not include any cost of removal installation or transportation 4 More Years Should the unit be otherwise than warranted Lyons Industries Inc will pay 10 of the sink value toward repair or exchange of a defective unit The exchange of a unit will be limited to supplying a replacement unit or component part of comparable size and style and does not include any cost of removal installation or transportation Lyons Industries Inc reserves the right to require the return at the purchaser s expense of the damaged product for repair or exchange before providing the services under this warranty Warranty does not cover damage that can be repaired by following the Scratch Removal Instructions or the Care and Cleaning Instructions This warranty excludes normal wear and tear This war ranty shall be voided by improper maintenance contrary to use and care Instructions This warranty does not apply to units installed in commercial or business establishments hotels or apartments Nor does the warranty apply if the unit is moved from its place of initial installation subject to accident abuse or misuse No warranty will apply if the unit is not installed in accordance with the instructions supplied by Lyons Industries Inc local building codes and ordinances or if the care and cleaning instructions have n
7. ot been followed Any implied warranty of fitness for a particular use or purpose or warranty of merchantability is limited in duration to the express warranty provided herein unless a shorter period is allowed by law Lyons Industries Inc shall not be liable for incidental or consequential damages for any damage to building its contents or occupants Some states do not allow limitations of incidental or consequential damages so the above limitations and exclusions may not apply to you In such a state liability shall be limited to the extent permitted by state law Any claim under this warranty must be made in writing with your original proof of purchase enclosed to Lyons Industries Inc 30000 M 62 West Dowagiac Michigan 49047 to request performance by Lyons Industries Inc under the terms of this warranty After such notice a prompt investigation of the claim shall be made by Lyons Industries Inc who will promptly perform its obligation under the terms of this warranty FOR ASSISTANCE CALL 800 458 9036
8. t paper possible repeat the sanding process using successively finer grits 600 2000 grit uw of paper until you ve once again sanded with 2000 grit oe Now use 3M rubbing compound 05933 on a soft damp cloth Polish using considerable pressure to produce a smooth shinny finish SCRATCH SANDPAPER GUIDE LYONS PREMIUM CAST ACRYLIC KITCHEN SINK LIFETIME LIMITED WARRANTY Lyons Industries Inc warrants to the original purchaser that this Kitchen Sink will be free of manufacturing defects which affect the performance of this product for the use it was intended The warranty period begins when the consumer user purchases the unit FROM DATE OF PURCHASE 15 Year Should the unit be otherwise than warranted Lyons Industries Inc will repair or exchange a defective unit The exchange of a unit will be limited to supplying a replacement unit or com ponent part of comparable size and style and does not include any cost of removal installation or transportation 2 4 Year Should the unit be otherwise than warranted Lyons Industries Inc will pay 50 of the sink value toward repair or exchange of a defective unit The exchange of a unit will be limited to supplying a replacement unit or component part of comparable size and style and does not include any cost of removal installation or transportation 3 Year Should the unit be otherwise than warranted Lyons Industries Inc will 25 of the sink value toward repair or excha
9. umber s putty CARE AND CLEANING INSTRUCTIONS Clean surface with nonabrasive liquid detergent and warm water Use cleaning products such as Soft Scrub Gel Comet Gel Gel Gloss or other similar products DONOTUSEABRASIVE CLEANERS steel wool orwire brushes on surface Caustic drain cleaners may cause surface damage Open flames cigarettes candles etc may damage surface Surface damage light scratches dulled areas and small cuts and are restored by first scrubbing with automotive type white body cleaning compound such as Meguire s 9 Swirl Remover followed by an application of Gel Gloss See next page for detailed Scratch Repair Instructions Remember to always use a cutting board or sink protector when using knives or sharp objects in your sink The finishing touch Recommendation When pouring boiling water or placing hot pots or pans into the sink run some cold water simultaneously LYONS INDUSTRIES INC WARNING Some cleaning products are not suitable for use Read all labels carefully 30000 M 62 West Dowagiac MI 49047 DO NOT USE if they say not suitable for use with ABS acrylic or polystyrene phone 800 458 9036 fax 269 782 5159 lyonsindustries com e mail lyonsind lyonsindustries com 4000 00153 8 15 11 27 1 4 T 15 1 4 KSxxA KSxxAB 24 3 4 13 1 4 L KSxxB 5 1 4 1 5 1 4 15 1 4 15 1 4 4 L 15 1 4 S
Download Pdf Manuals
Related Search