OPERATION MANUAL - ArtGuard Security
Contents
1. PIN code access attempts on five consecutive occasions will immobilize the lock for 5 minutes During this period any button on the keypad will be non responsive USING THE LOCK Unlocking from outside PIN code access The power button on the outside unit is used to trigger the night vieuw light beneath the PIN code keypad It will last for 3 seconds with no operation following but will not turn off until any operation on the keypad is accomplished 1 Fully lift up the outside sliding cover 2 Directly enter one existing PIN code or or PWR button 3 When you hear the motor moving turn down the handle to unlock and enter the room When the power is lower than 3 3V the lock will send out low power alert You will hear 8 beeps and see the Red LED blink Change the batteries as soon as possible Unlocking from outside with the override ke Access Insert the override key vertically turn it clockwise to 90 degress Then push down the handle to open the door Unlocking from inside Exit Directly push down the handle to unlock the door from inside TROUBLE SHOOTING Trouble Possible reasons Solutions 1 The lock cannot be open properly after a preset PIN code is entered 1 Low battery power 2 The clutch does not work 3 The spindle not installed properly 4 Electronic damaged 1 Change batteries 2 Check and repair the clutch 3 Re install the spindle axactly to the proper mark2. 4 Replace the electronic parts 2 Handles are too tight to be turned 1 The spindle does not match the door thickness 2 There is a declination for the existing holes 1 Use new lock whose spindle does match door thickness 2 Adjust the location of fixing holes 3 The inside handle cannot be locked 1 The inside spindle tube not installed properly 1 Adjust the spindle tube exactly according to the mark on it After sales service ArtGuard Security Albert Plesmanweg 3A 4462 GC Goes The Netherlands 31 113270166 info artguardsecurity eu
3. ArtGuard Security The Point where Life amp Science interact OPERATION MANUAL LP 903 PIN LOCK Adding the PIN codes There can be ten individual sets of PIN codes The set number ranges from 0 to 9 The original factory PIN code is 123 The PIN code can be set from 1 and up to 10 digits Note 1 is only a follow up mark not a functional button 2 The 0 and 1 set PIN codes are the Master PIN codes of the lock A ADD the Master 1 PIN code enter 0 123 Green LED blinks New PIN code Green LED blinks again New PIN code again B ADD the Master 2 PIN code enter 0 the 0 set PIN code Green LED blinks New PIN code Green LED blinks New PIN code again C ADD the USER PIN code enter 2 9 one of the Master PIN codes Green LED blinks New PIN code Green LED blinks New PIN code again Note When the Green LED blinks and one long beep is heard the operation was successful If the Red LED blinks the operation fails Repeat procedure Deleting the PIN codes Enter PIN code number which must be deleted one othe Master PIN codes When the Green LED blinks the deletion was successful if the Red LED blinks the operation failed Example If we want to delete the 2 PIN code thuse second User enter 2 one of the Master PIN codes NOTE The Master PIN code can not be deleted this way They can be deleted nly by resetting the loc
4. k Call your vendor or ArtGuard Security at 31 0 113 270730 after sales service Temporary Unlocking Mode TUM amp Automatic Locking Mode ALM Note The original factory mode set up is Automatic Locking Mode ALM Enter 1 one of the Master PIN codes Green LED blinks 1 to trigger Tmporary Unlocking Mode TUM When the Green LED blinks again and one long beep is heard the lock enters into TUM User can now turn down the handle without the need to enter any PIN code Lock function like every other handle Enter 1 one of the Master PIN codes Green LED blinks 0 to get the lock back into Automatic Locking Mode ALM When the Green LED blinks again and one long beep is heard the lock enters ALM User cannot unlock from outside before one of correct PIN codes is entered Note Temporary Unlocking Mode TUM might possibly get your house or office into insecure situation Unless you are sure it s 100 necessary and safe it is strongly recommended not to get this function applied Anti Malicious Operation Setup AMO Enter 2 one of the Master PIN codes Green LED blinks 1 to trigger AMO functionality When the Green LED blinks again and a long beep is heard this functionality is triggered Enter 2 one of the Master PIN codes Green LED blinks 0 to cancel AMO functionality When the Green LED blinks this functionality ceaces to work Note When AMO Setup is applied and wrong
Download Pdf Manuals
Related Search