EASY HOME / EASY MOBILE - produktinfo.conrad.com
Contents
1. How to solve malfunctions Strange signal sounds Strange display behaviour Errors in fingerprint recognition Malfunction in using the system menu Red controller LED is on Alarm sound and or blue controller LED is active Troubles with connected external systems and opening devices The reader is not working Door opener is not reacting upon inner touch sensor The blue LED of the reader is not working and no sound appears while opening and closing the sensor cover While opening the reader cover a strange sound melody occurs The system doesn t react upon X key Please check the power supply Most of the malfunc tions are caused by weak power or power overload Optimal power supply is 12 V DC 2 A Please check the link between reader and controller this is a com bined data and power supply line Please check the A arm and Door contact settings May the alarm function was activated without connect ing a door contact Please check the Connectors settings Please check the RS 485 cable link between both units Please check that a unique system ID has been selected DIP switch on reader back side and system settings Device ID Perhaps Out mode settings are not correct Please read the related chapters Please check the wiring too The link between reader and controller seems to be broken Please re check In case that no fingerprint has been stored yet the reader signals with special sound Ma2. In most cases the maximum duration is limited to 1 minute Step by step guide Display Input 2m 8 k mem EN uuD us E A mun uen mm rios D m D umm mum Em How to activate the door sensor The controller is equipped with a sensor input that is prepared for a NC normally closed door contact i e a dry reed contact The system can detect that the door is open and react accordingly Please check the installation guide for proper installation The door contact is disabled by default You may enable as explained herein 1 Enables the door contact 2 Disables the door contact When enabled and the door is open the out puts will remain active until the door will be closed again The relay time will be ignored Example If you use a magnetic door lock the magnet is inactive until the door is closed This will save power and extend lifetime of the coil inside the lock Step by step guide Display Input oOo alas 17 ce 0 br How to set the system ID Due to security reasons reader and control ler must be paired In case of exchanging the reader the system will not work The units are paired by factory settings Un der normal conditions it is not necessary to change the ID Anyhow if you like to change the system ID you may select a system ID from 1 to 15 You need to change the ID via DIP switch on the back si
3. be con nected to the Easy Home In case that large electrical loads must be switched heavy duty relays can be integrated in between For ex ample sliding doors garage doors shutters etc Another application field is the controlling of alarm systems with the Easy Home Easy Mobile As explained above the Easy Mobile meets the requirements of mobile applications The system is well protected against environmen tal influences and it is designed to consume only a minimum of battery ressources in stand by mode But of course the system is only applicable if an electro mechanical door locking system is installed too In best case your car is already equipped with a central door locking system Otherwise please contact your local dealer to check the possibilities for backfitting There are at least two ways to connect the Easy Mobile By wire Both relay contacts can handle loads up to 130 mA to switch circuits directly In all other cases you may need to interpose heavy duty relays In both cases you should try to find the connecting points to your central locking By remote control If you own a remote controlled locking the easiest way is to get a free remote sender With a little experience you can connect the relay outputs of the Easy Mobile to the push buttons of the sender module Both solutions require good knowledge about your car s locking system If necessary please consult your dealer or a specialist T
4. skin ridge pattern is exact the same than on the surface Therefore this sensor type is more applicable for children with soft and people with dry and horny skin can also handle small injuries like scratches or cuts Furthermore the sensor can recognize replica fingers In comparison to swipe sensors at which the finger must be drawn with the same speed and accuracy at any time over the sensor the handling of a flatbed sensor is as easy as pushing a simple button Because of all the above mentioned reasons the Easy Home Easy Mobile system is suit able for all day usage for families and small offices and contributes a high level conven lence How to use the CAMOS systems Easy Home was developed for the use in the automotive industry The approval regulations are much stronger than for domestic applica tions particularly with regard to more inten sive environmental impacts such as sunlight moisture or temperature fluctuations Since our products meet those requirements they are most suitable for domestic usage To use the Easy Home you need to install an electromechanical door locking system The most popular method is an electric strike the most elaborate seems to be an integrated motorized door lock Both methods differ not only in security level but also in cost and in stallation effort Every average DIY might install an electric strike If necessary consult an expert Various kinds of locking systems can
5. software versions before calling This might help to fix the troubles quickly The version numbers of controller and reader do not match This is no mistake Step by step guide Display Input 2m uM E E ee Amm EN S Nus 0 mS rem 2 Fear E mm vem mos e 1 Specifications and connector limits Fingerprint reader BMR 207 Sensor technology Sensor type False Rejection Rate FRR False Acceptance Rate FAR Reader speed ESD protection Wear protection cycles Dust and moisture protection Internal communication Dimensions Width x Height x Depth Weight Operating temperature Power supply Active capacitive hybrid Flatbed sensor lt 0 01 lt 0 001 0 5s 30 kV gt 1 000 000 IP 54 RS 485 reader controller max 300 m 63 x 91 x 25 mm 160 g 20 70 C 5 V via controller BMT 212U Controller with Display BMT 212U Storage capacity Dust and moisture protection Internal communication Outputs in DC mode Outputs in relay mode Input Dimensions Width x Height x Depth Weight Operating temperature Power supply Power consumption 100 finger templates IP 54 RS 485 reader controller max 300 m 2 x 9 27 V out max load 450 mA closed current open current 1 99 s 2 x NC opener or NO closer Max load 350 V 130 mA 1 x NC door contact opener 63 x 170 x 33 mm 300 g 20 70 C 9 27 V optimal 12 V 9 mA Stand by max 100 mA
6. 0000 1 E 3 Updating the controller firmware The update functionality is meant for special ist usage only and to update new language files A consecutive update is not necessary and updates will be provided only in case of com plex matters The access via PC USB to the biometric sys tem requires a special software Otherwise it is not possible to get access o Don t use this function without ex plicit instructions Once the system is set into update mode it will not react on key pad nor fingerprint activity In this case it must be returned to an authorized service team or to the manufacturer Step by step guide Display Input 2m 0 0 INN ENB ENB 7 gt acere br How to return to default values If some of your settings do not have the ex Step by step guide pected effect or if you lost the overview you may re set the system to default values Display Input 2m ee ees 0 Nu 0000 E 0000 Stored fingerprint templates will not be de leted If you sell the system or will not use it any longer please do not forget to delete all fin gerprints for security reasons EN m How to retrieve controller 1 and reader 2 firmware version In case of trouble shooting please check all connectors and wiring first If it is still necessary to achieve technical help of our service team check and write down the
7. 1 is switched Factory mode is 1 br Setting the relay time In case of positive fingerprint recognition the outputs will be operated as per settings please see previous pages The duration of the output activity is triggered by the relay time value The period may be set from 1 to 99 seconds Please read the manual of the external device to find out optimal settings Step by step guide Display Input oOo LT a ese y rasse Quick test for output 1 The system is configured to work with a Step by step guide standard electric strike by factory default Display Input 0000 0000 E Usually the strike will be connected to output 1 since this port can be operated by touch sensor on the controller compare installation guide To check the port settings and the wiring after installation you may use the quick test func tion Complete system connector test This function will start a complete connector test and will check the fingerprint reader If the system ID is displayed correctly the reader is well connected Otherwise please check the link Afterwards the outputs 1 and 2 will be switched 3 times At least the input will be checked To complete the test please operate the door contact at least one time If you didn t connect a door contact to the system please ignore the error message Step by step guide Display Input
8. CAMOS BIOMETRIC FINGERPRINT RECOGNITION CAMOS AT User Manual You have purchased a high quality hi tech product Please handle with care and caution gt gt gt Never open the units You may risk an electrical shock or to damage sen sitive parts In case of any defect please power off the system and consult your local dealer or the manufacturer This system is designed for use with 9 27 V low power supplies only While installation and usage don t handle with violence In most cases malfunctions have a reason Please install the system according to usual precautions Be aware of unprotected electrical power wires Please clean the system with soft cloth Don t use oily acid or soapy liquids Please use the sensor with your fin gers only Sharp objects or extreme force may damage it In case the sensor is very wet please use a dry soft cloth to clean it Water cannot damage the sensor but it can decrease the reading capability Safety advise Dp PP D Even if the system locks or unlocks your house or car you will be held responsible for proper locking Leaving your house or car please make sure that it is properly locked Before selecting and installing an electromechanical locking system please check your insurance police if and which means are covered Please be aware that children s fin gerprints may vary during their ado lescence Normally you should r
9. cessary and might be skipped Cancel the current job leave the system menu de lete a character text input e eee o m om om om mom The menu structure and navigation To set up the system you need to navigate through the below menu structure For this purpose you will use the keys 2 1 87 and 7 For a better understanding please imagine a virtual 2D button Menu functions which are password protected separately are marked with gt The basic functions are available after single login into the system menu Some expert settings require exact knowl edge about the functionality of the BIOLOCK components Access to these functions will be granted by re entering the PIN number Please read this manual carefully before changing any settings Login and access to system stettings and functions The access to the main menu is protected by a personal identification number PIN The factory default PIN is 1234 It is recom mended to change the PIN immediately after first login On the following pages all functions will be ex plained To achieve a higher legibility the login procedure will be shown in a short form ENB 77 After an adjustable time the system will auto matically log off This minimizes the risk of an unauthorized access to essential functions The factory value is 10 seconds It is recommended to log off manually after finishing your current job as described on th
10. de of the reader and the settings in the system menu An overview of the valid DIP switch settings and its meaning you may find in the installa tion guide Step by step guide Display Input 2m 0 0 NUN i emm mm 0 ENB ee 8 umm mm How to operate output 1 The controller offers two separately config urable outputs Each output can be operated either as switch able DC supplier or as potential free relay contact The mode selector DIP switch is located on the back side of the control unit The meaning of the DIP switch setting is ex plained on the next page You will find the specification of the outputs in chapter Techni cal Data Specification on page 30 If operated as DC supplier the ports can work as open current or closed current terminals If used as relay contacts the ports can work either as NO or NC contact DC mode default Relay mode 1 No power out in Contact open in normal status normal status 2 Power out in nor Contact closed in mal status normal status Factory default for output 1 is DC mode and open current i e power off in normal status An electric strike can be connected to this port without changing any settings Step by step guide Display Input 2m 8 m mm Pn ren n ess D mm m mm Goer 9 rro D m Posmi br How to operate output 2 Output 2 works similar to output 1 You will find a detailed explanation on th
11. e enrol every six months Just to be on the safe side it is rec ommended to enrol at least two fin gers per person Thank you for purchasing an Easy Home Easy Mobile System 2 SAFETY INSTRUCTIONS 21 CONNECTORS 4 BASICS A Sid 4 Technology a 5 Applications ou mee 24 Relay time p 25 SYSTEMCHECK D APENI 25 Check door 7 Key pad 8 Menu structure i ne 9 Login 27 FW UPDATE 10 New PIN 27 Controller 11 Language 28 Set default 12 Enrol new 29 FW INFO 13 Fingerprint Sensor Usage 29 Controller and Reader 14 USER MENU 30 TECHNICAL DATA 14 Verify ID 30 Specifications 15 Delete ID 17 SETUP 17 Sleep timer 18 Alarm 19 Door sensor 20 Device ID Produced by CAMOS Europe GmbH Copyright 2007 CAMOS Europe GmbH Printed in Korea All rights reserved Subject to change without prior notice All product names might be brands or registered trademarks All rights re served Reprint nor in extracts is not permitted without our express written approval About biometrics Biometrics refers to all kind of methods for uniquely recognition of humans based on one or more specific physical or behavioural characteristics The more unique those char acteristics are the more they are applicable for definite identification The oldest of all biometric methods is the finger print identification the so called dactyloscopy greek dactylos finger and scopein view 1896 in Argentina the dactyloscopy was intro duced country wid
12. e right side Step by step guide Display Input 2 7 You are logged in Step by step guide Display Input ia 2 You are logged off fa How to change the PIN The default PIN is 1234 It is highly recommended to change the PIN to a per sonal value The PIN might consist of 4 up to 12 digits The longer the PIN is the more secure it is Opti mal protection is achieved with a minimum of 5 digits Usually PINs should not show any relation to your personality such as birthday age etc The main unit of the BIOLOCK system will be installed inside The risk of spying out your PIN by a third party might be considered as relatively low However if you feel that you have been observed while entering your PIN please change immediately For professional applications periodical changing of the PIN is recommended Step by step guide Display Input 2m MD 0000 LB mm ee m m 5 E NE 0 m I How to select another language The default language for the display and the menu is English With less effort you can se lect your favourite language Please follow the instructions on the right re booting the system is not necessary Step by step guide Display Input 0000 h Register new fingerprints Fingerprints will be stored as so called Tem plates in the memory of the control unit It is not possib
13. e for criminal investigations Nowadays these methods become more and more accepted as access control method A biometric system uses three components the sensor the trait extraction enrolment and the comparison The sensor sends as result a fingerprint tem plate This template is an extract that is ad justed for optimal results After the enrolment the template is digitally encrypted and stored It is not possible to re construct a complete image from the template While using the biometric system the stored template will be compared to the current one If the matching rate is within certain toleranc es the template will be accepted as valid The most significant quality and reliability traits of a biometric system are its failure rates The False Acceptance Rate FAR and the False Rejection Rate FRR More critical for consumer applications is the FAR value It is more dangerous when an un authorized person gets access than the rejec tion of authorized persons Besides a quick algorithm the sensor is the most important part for the reliabilty speed and security of the biometric system The Easy Home Easy Mobile is equipped with a high performance sensor using the latest available technology It is a so called active capacitive hybrid sensor This sensor doesn t take a picture of the finger surface it measures the conductivity of the saline layer below the dry epidermis Since the young skin is build there the
14. e previous page The factory setting for output 2 is DC mode and operating current in normal mode With out any modification you can connect a door magnet to the output 2 You can configure the port as explained on the right Step by step guide Display Input DEM 6070 LE Domen LE uuum LI Bors Out1 amp Out2 DC mode Out1 DC mode amp Out2 Relay mode Out1 Relay mode amp Out2 DC mode Out1 amp Out2 Relay mode How to connect external devices to the outputs The control box offers two outputs to be con Step by step guide nected with door openers optical or acous tical signal indicators Also they can be con Display Input nected to sensor inputs of alarm systems T m se m mem mem me long 2 3 sec finger contact For your sup port the reader will signal by pulse sound Available modes EE 707 mem mom rem Ec Both outputs can be operated synchronously or independently from each other The system can distinguish between short 3 sec and 1 Only output 1 is used Output 2 is free for alarm function 2 Only output 2 is used Output 1 is free for alarm function 3 Both outputs will work synchronously 4 On short finger contact 3 sec output 1 will be operated on long finger contact 2 3 sec output 2 is switched 5 On short finger contact lt 3 sec output 2 will be operated on long finger contact 2 3 sec output
15. he components Fingerprint reader Controller Mounting bracket Reader Main unit Mounting bracket Outdoor reader with mounting bracket and 4 Pluggable screw terminals with 2 4 and 6 rubber fitting pins Controller with mounting bracket and 5 Two core installation wire 5 m furniture protector 6 Screws and small parts Data cable reader controller 1 m 7 Not shown manual installation scheme oe How to use the key pad and how read the step by step guide All component settings are prepared to work out of the box after installation The major tasks after the installation are to set the master password and to enrol the fingerprints of the authorized persons For more individual settings the control unit is equipped with a display and a key pad On the following pages all expert functions will be explained step by step Please make yourself familiar with the signs and symbols on the right side abc def mimm ghi jkl mno as cna Laan pars tuv WXyZ mir lance PROGRAMMER Signs and symbols Illustration eem mom Em m abe xyz eS a ae aa ea eT a Explanation The keys shown must be pressed successively For entering numbers the digits from 0 to 9 are valid Value range up to 99 For input numbers and let ters are acceptable Please use the key pad similar to the T9 key oad of mobile phones Valid values are 1 or 2 only Input is not ne
16. le to re construct complete finger print images from the templates but to com pare two templates with each other The memory is organized like a relational da tabase i e every fingerprint will be assigned to a unique storage index ID number Every new fingerprint will be allocated to the next available ID The ID can also be assigned manually during the enrolment It is recommended to keep a separate list of the assigned ID numbers and reference it to user names This will enable you to delete or overwrite individual templates very easily If you want to overwrite a used memory ID you must confirm the hint in the display by pressing F Step by step guide Display Input How to use the fingerprint reader Open sensor cover Blue LED turns on As smoothly as possible Place finger smoothly Close sensor cover and straight gt gt pD For security reasons there is an inte grated time out after 3 seconds For security reasons you will have only three attempts for fingerprint recognition After that you have to close and open the cover again If the sensor position is inconvenient for using your forefinger we recom mend to use your thumb Please find your way to place the fin ger with the biggest possible contact area Try to use the swilley for orien tation Verify existing fingerprint templates After enrolment you might want to verify the Step by step g
17. r You can log off the system menu whenever Step by step guide your current task is completed by pressing the 7 1 key Display Input le LJ b 0 use yy Esie rer In case that you cannot finish your job or if you get distracted the system will log off after a certain period for security reasons This period for the sleep mode timer can be adjusted from 5 to 99 seconds br How to use the alarm function The control unit provides a sensor input that operates as normally closed NC door switch This means the quiescent current will be interrupted in case of opening the door For example you can connect a dry reed con tact NC The system can react with various activities The alarm function is deactivated by default and can be activated as explained in the right side 1 Enables the alarm function 2 Disables the alarm function After activating the alarm function you may select one of the three modes 1 Upon alarm event output 1 will be com mutated 2 Upon alarm event output 2 will be com mutated 3 Upon alarm event the controller will indi cate optically and acoustically only with out changing the outputs The alarm can be disarmed by a valid PIN number or positive fingerprint matching only Best usage for optical alarm signal When you return to your home or car you can see from the distance that something happened Please consider local regulations for acoustic alarms
18. uide fingerprint Please enter the ID and let the system check your finger again Display Input re It will enable you to test several times without activating the door opening mechanism rer EN This function is helpful if the reader must be installed in a difficult position and in case you are not sure that placing the finger is conven ient for you for a longer time How to delete one fingerprint template A single fingerprint template can be deleted by its storage number its ID Vice versa you cannot delete a fingerprint without its ID If you want to use the system with a high volatile user group it is recom mended to keep a separate list with user to ID reference Otherwise the database must be erased completely and the remaining persons must be registered again Alternatively you might assign the storage IDs manually to differentiate user groups i e 0 19 for family 20 39 for guests etc This will enable you to distinguish between permanent persons and guests Step by step guide Display Input 0 0 EUN 0000 EE m ress cnt How to delete all stored fingerprint templates You can delete all stored templates in one Step by step guide step Display Input Please use this functionality carefully the re maining persons must be registered again 2 m BB mu gt Em a a How to set the sleep time
19. ybe the power supply doesn t meet the require ments or there is a problem with the wiring Distributor IMC GmbH Carl Zeiss Str 7 22946 Trittau info imc multimedia com Version 01 20071129 Printed in Korea
Download Pdf Manuals
Related Search