Manual for 3537003
Contents
1. Video out cable 2 4 Tool Components The MaxiVideorm MV301 comes with the following items Here 8 5mm diameter imager head and _ its matching accessories magnet hook and mirror are shown below as an example Note Because of continuing improvements actual product 5 www ecutool com info sinosells com 1 2 3 4 5 6 7 8 9 10 11 Handheld Display Unit The ergonomic tool with comfortable pistol grip design Cable Connector Connects the handheld display unit to the imager head and cable Imager Head and Cable Connects to the instrument while in use to view images and videos Power Indicator Light Illuminates green once the tool is turned on Tool s Signal Output Connects to the monitors signal input to function properly Roll Switch Turns onthe power of thetool and adjust brightness of LEDs Battery Compartment Cap Indicates to install or remove batteries LCD Screen Indicates test results Backlit 320x240 pixels display with LED lighting adjustment Accessory Magnet Picks up metal objects such as dropped rings or screws on the floor Accessory Mirror Helps users look around corners and see inside the unreachable areas Accessory Hook Unclogs obstacles and picks up wires in the pipes or confined areas ye Ca 9 Ly Fig 2 6 www ecutool com info sinosells com 2 5 Buttons and Controls Fig2. 3 A LCD Screen Indicates test results Backlit 320x240 pixels display with LED lighting adjustment B Power Button Turns on off the tool C Reverse Button Controls the direction of the real time image D Monitor s Signal Input Connects to the tool s signal output to function properly E Monitor s Power Light Indicator luminates green once the monitor is turned on F Video Out Port Connects the tool to a TV with the supplied video out cable to view real time images G AC Adapter Port Charges the monitor using an AC adapter 3 Installation 3 1 Battery Removal and Installation 7 www ecutool com info sinosells com NOTE If the power indicator light is blinking continuously this reminds you to replace batteries in time as instructed Screw e E ml Battery Compartment Cap Fig 4 1 Turn the handheld display unit upside down to expose the battery compartment cap and screw Fig 4 2 Use ascrewdriver to remove screw and battery compartment cap 3 Battery removal and installation Battery Compartment Fig 5 Y To remove the batteries hold handheld display unit to remove the battery compartment and then remove batteries Fig 5 v To install the batteries remove the battery compartment and insert four 4 new AA batteries 8 www ecutool com info sinosells com into the proper slots in the battery compartment 4 Proper battery orientation is indicated in the
3. battery compartment 5 Replace the battery compartment and screw using a screwdriver to close the battery compartment cap 3 2 The Imager Head and Cable Installation To use the tool the imager head and cable must be connected to the handheld display unit To connect the cable tothe handheld display unit makesurethe key andslot Fig 6 are properly aligned Once they are aligned finger tighten the knurled knob to hold the connectign firmly m place Fig 6 Warning Ensure to only tighten or loosen the knurled knob and not the shaft 3 3 Accessories Installation The three accessories include magnet hook and mirror Fig 2 All are attached to the imager head in the same manner Hold the accessory and the imager head as shown in Fig 7 slip the end of the accessory over theflats of theimager head and then fix the accessory as shown in Fig 8 9 EY Fig 7 EN Fig 8 3 4 Video Out Cable Connection Insert the supplied video out cable into the video out port of the tool and the other end of the cable into the video in port of a TV the LCD screen will output a high quality real time image 3 5 LCD Monitor Installation Correctly align the connecting areas and gently slide the monitor downward so that the monitor is securely attached to the instrument as indicated below 10 www ecutool com info sinosells com Fig 9 3 6 Monitor Charging LCD monitor can be charged by
4. that this product will be free from Use the roll switch to adjust brightness Ensure adapter cable is connected between monitor and adapter Ensure adapter is plugged into the wall socket all defects in materials and workmanship for a period of one 1 year from the date of the original following terms and conditions 1 The sole responsibility of Autel purchase subject to the under the Warranty is limited to either the repair or at the option of Autel replacement of the tool atno charge with proof _of purchase The sales receipt may be used for this purpose www ecutool com 19 info sinosells com 2 This warranty does not apply to damages caused by improper 3 4 use accident flood lightning or if the product was altered or repaired by anyone other than the Manufacturer s Service Center Autel shall not be liable for any incidental or consequential damages arising from the use misuse or mounting of the tool All information in this manual is based on the latest information available at the time of publication and no warranty can be made for its accuracy or completeness Autel reserves the right to make changes at any time without notice 6 2 Service Procedures If you have any questions please contact us If it becomes necessary to return the tool for repair contact your local distributor for more information 20 www ecutool com info sinosells com
5. 1 Safety Instructions IMPORTANT To avoid electric shock fire and or personal injury or damage please read this user s manual carefully and follow the safety instructions 1 1 Work Area Safety Always perform automotive testing in a safe environment Keep your work area clean and well lit Cluttered benches and dark areas may cause accidents Keep clothing hair hands tools test equipment etc away from all moving or hot engine parts Keep a fire extinguisher suitable for gasoline chemical electrical nearby Operate the tool in a well ventilated work area Do not operate the tool in explosive atmospheres such as in the presence of flammable liquids gases or heavy dust Donot use thetool around corrosive chemicals which can damage the tool Do not abuse thecable Never use the cable to carry the tool Keep bystanders children and visitors away while operating the tool Keep the tool dry clean free from oil water and grease Use a mild detergent on a clean cloth to clean the outside of the tool when necessary 1 2 Electrical Safety Avoid body contact with earthed or grounded surfaces such as pipes radiators ranges and refrigerators Donot expose thetool torainor wet conditions Water entering the tool will increase the risk of electric shock Donot abuse thecable Never use thecable for carrying pulling or unplugging the tool Keep cable away from heat oil sh
6. Use the supplied accessories to provide application flexibility 6 Connect the supplied video out cable to video out port of the tool and the other end of the cable to the video in port of a TV to view a high quality real time image 7 Detachable 3 5 TFT LCD wireless monitor allows for remote inspection up to 32ft 10m from the measuring point Fig 12 Note The shaft provided is flexible and bendable which helps you to explore into difficult to reach and confined areas www ecutool com info sinosells com Fig 12 Attention when the camera is in wireless mode both the monitor and the tool will expend their batteries When the camera is in wired mode only the lithium ion battery in the monitor is used 4 2 Operation Precautions CAUTION Do not put the toolinto anything or anywhere that may contain a live electrical charge Do not operate the tool unless the user s manual has been read thoroughly and proper training has been completed Do not immerse the handheld display unit in water Reduce the risk of electric shock and damage Do not use the tool if condensation forms inside the imager head Let the water evaporate before using again Do not use excessive force to insert or withdraw the cable Donot use theimager head and cable to modify surroundings clear pathways or clogged areas www ecutool com 14 info sinosells com The handheld display unit isnot waterproof The imager head andi
7. ach areas from aremote location up to 32ft 10m The ergonomic tool features comfortable pistol grip design autofocus and viewing capacity as close as 1 with crystal clear output Available with various sizes of camera heads 16mm 8 5mm and 5 5mm the MaxiVideo Videoscope is an economical solution to inspect machinery facilities and infrastructure in the safest fastest and most cost effective manner possible 2 2 Specifications Recommended Indoor use Optimal viewing 1 to 14 2 5 cm 35 6 cm distance IPG mager 640 x400 Image control Low Light Vision Screen type 3 5 TFT LCD display 3 www ecutool com info sinosells com Display resolution Rechargeable Li ion battery in monitor amp Power supply 4x AA batteries in camera T va 4 5 hours of continuous use battery life T PE 32ft 10m unobstructed view range Bandwidth 18MHz Frequency 16mm 0 63 Camera Head 8 5mm 0 33 V5 5mm 0 22 Lighting Fully adjustable LED 8 5mm 0 33 is standard Imager head 16mm 0 63 and mt 5 5mm 0 22 are optional Main Unit 32 F to 113 F 0 C to 45 C temp Cable 14 F to 176 F 10 C to 80 C 1m 3 expandable to 5m 16 w Optional Cable reach Extensions www ecutool com info sinosells com 2 3 Accessories Included 1 Blow molded case 2 AC adapter 3 User s Manual 4 Imager head and cable 16mm 8 5mm 5 5mm 5 Magnet hook and mirror 6 4x AA Batteries 7
8. arp edges or moving parts 1 If operating the tool in a damp location is unavoidable use a ground fault circuit interrupter GFCI to protect supply 1 3 Personal Safety Donot use thetool while tiredor under the influence of drugs alcohol or medications A moment of interruption can result in serious personal injury Donot over reach Keep proper footing and balance at all times Proper footing and balance enables better control of the tool in unexpected situations Always wear safety eye protection that meets ANSI standards Donot wear loose clothing or jewelry Keep your hair clothing and gloves away from moving parts Loose clothes jewelry or long hair can be caught in moving parts Donot place the tool onany unstable cart or surface The tool may fall causing serious injury toapersonor serious damage to the tool itself Turn off the instrument when not in use Donot spill any liquid on the monitor Liquid can lead to possible electrical shock as well as damage to the product Do not use the tool for personal or medical use in any way The product is not shock resistant Do not use it as a hammer or drop it www ecutool com info sinosells com 2 Description Specifications and Tool Components 2 1 Description This premier Autel MaxiVideo MvV301 digital videoscope features a detachable wireless 3 5 color TFT LCD monitor The wireless capability aids you in examining difficult to re
9. connecting to a wall outlet using an AC adaptor Plug the AC adapter into the AC outlet Once the AC adapter isplugged in the lithium ion battery will begin charging with the red light indicator on during charging Once the battery is fully charged it will turn off automatically with the greeplight indicator on If the monitor ischarged without the lithium ion battery being installed the green light indicator and the red light indicator would be on and flash respectively Note The monitor can be used while charging 4 Operation Instructions 4 1 Basic Operation NOTE When in operation the cable can be bent into a certain shape This may help you operate the cable into confined areas CAUTION Keep the cable away from heat oil sharp edges or moving parts Replace damaged cables immediately 11 1 Toturn the tool on hold thehandheld display unit with LCD screen facing you 2 Press Power button to turn on the screen The power indicator light will illuminate green The real time image will appear on the LCD screen 3 Roll the on off switch to start the camera This switch also serves as a dimmer for LEDs which provide superb quality lighting See below Fig 10 4 Press Reverse button to control the direction of the real time image The real time image will do a horizontal reverse or vertical reverse See Fig 11 www ecutool com info sinosells com 12 Original Position Fig 11 5
10. r inspecting the inside walls be sure to turn off the circuit breaker tothe whole house before using the tool FOR AUTOMOBILES Make sure the vehicle is not running during the inspection Metal and liquid under the hood may be hot Don t get oil or gas on the imager head 4 3 Battery Precautions Remove the batteries while cleaning the tool When necessary replace all four 4 batteries with new ones Use only the size and type of batteries specified Properly dispose of batteries Exposure to high temperatures can cause batteries to explode Do not dispose in fire The AC adapter is only used for charging the monitor Be sure to install batteries with the correct polarity as indicated in the battery compartment Remove the batteries before storing the tool for a long period of time to prevent battery leakage from damaging battery compartment www ecutool com 16 info sinosells com 4 4 Maintenance Instructions NOTE Make sure the batterieshave been removed from the tool before performing maintenance Tool maintenance must be performed only by qualified repair personnel Maintenance performed by unqualified repair personnel could cause injury When maintaining use only identical replacement components Donot attempt totakeany pieces of thetool apart unless directed by the manual Do not use acetone to clean the tool Instead use alcohol Avoid rubbing too hardon the LCD screen After using wipe the displa
11. tscover are waterproof but not acid proof or fireproof Avoid submersing the imager head into corrosive oily places and be sure to keep the imager head away from high temperature objects Donot put theimager headand cable into anything or anywhere that may contain a live electrical charge If the tool does not work well after turning it on Please take batteries out and do not use Please have the tool checked by a qualified technician Any tool that cannot be controlled with the power button is dangerous and must be repaired Store idle components out of the reach of children and other untrained persons Maintain the tool with care Properly maintained tools are less likely to cause injury If the tool is dropped check for the breakage and any other conditions that may affect its operation Use only accessories that are recommended by the manufacturer of the tool Dry your hands when operating the tool or replacing batteries Protect against excessive heat The tool should be kept away from heat sources suchas radiators stoves or others that produce heat Store the tool in ventilated and dry places The flexible tube is not subject to sharp angle bends and such act may cause permanent damage to the shaft 15 NOTE Please check following methods to avoid injury v FOR PIPES If you suspect a metal pipe could contain a live electrical charge have a qualified electrician to check the pipe before using FOR WALLS Fo
12. y unit clean gently with a dry cloth Upon the completion of any maintenance of the tool ask qualified repair personnel to perform safety check to see if the tool is in proper operating condition Stop using the tool if it starts smoking or emitting noxious fumes Always handle the tool with care It isnot shock resistant and should not be banged or dropped Do not disassemble the tool beyond what is shown in the manual Doing so will void your warranty Follow instructions to replace accessories 17 5 Troubleshooting REASONS SOLUTIONS Check if it is Cable connection is covered by loose ied os Imager head is Display unit ison but does Check and not covered by debris reattach show image Monitor is Remove obstructed by obstructing objects objects LED on imagerhead are dim Replace at Batteries are low max brightness display batteries changes between black white and colof Replace display turns itself OFF afte a Check to see if short period The tool will not turn on Batteries are not the batteries are properly installed installed with correct polarity as indicated www ecutool com info sinosells com 18 Image too dim or too dark Monitor will not charge LEDs near camera require adjustment Cable are not accurately connected Adapter is not connected to power 6 Warranty Information 6 1 Limited One Year Warranty Autel warrants to its customers
Download Pdf Manuals
Related Search