User man 30 lb.vp - Scotsman Ice Systems
Contents
1. Because the ice machine is making a food product the water supply to the ice machine must be potable or fit for human consumption Electrical Voltage e Minimum 104 volts e Maximum 126 volts Models Options Door Panel kits Finished door panels are available from Scotsman for attachment to the machine or a custom panel can be made Kit Number Panel Finish Handle Finish KDFS Stainless Steel Stainless Steel Kickplate Extension In some situations the leg levelers will be extended enough to become visible A kit to extend the kickplate over the legs is KKPF Cabinet Stability In some free standing installations it may be prudent to add a bracket that secures the back of the cabinet to a wall That kit number is KATB Drain Conversion A gravity drain model can be converted to a drain pump model by installing a drain pump kit The drain pump kit consists of a drain pump wiring harness and associated tubing The part number is A39462 021 Warranty Information Warranty information is supplied separately from this manual Refer to it for coverage In general the warranty covers defects in materials or workmanship and does not cover corrections of installation errors or maintenance SCCPA30M 1SU Pump model stainless cabinet e SCCGA30M 1SU Gravity drain model stainless cabinet Cabinet Dimensions Width Depth w out door panel Depth with door panel handl2. Directions for this may be found in the section under cleaning Filters and Treatment In general it is always a good idea to filter the water A water filter if it is of the proper type can remove taste and odors as well as particles Some methods of water treatment for dissolved solids include reverse osmosis and polyphosphate feeders A reverse osmosis system should include post treatment to satisfy the R O water s potential aggressiveness Deionized water is not recommended Because water softeners exchange one mineral for another softened water may not improve water conditions when used with ice machines Where water is very hard softened water could result in white mushy cubes that stick together If in doubt about the water contact a local point of use water specialist for recommendations on water treatment Installation Overview The ice machine must be connected to cold potable water it must have a drain it must be connected to the proper power supply and must be able circulate air through the vents at the front November 2009 Page 6 SCCG30 amp SCCP30 User Manual Door Panel The ice machine is supplied without a conventional door covering so it can be decorated to the user s preference Scotsman offers several coverings including white black and stainless steel In addition a custom built panel can be placed onto the door Door Panel Attachment To attach a Scotsman supplied panel
3. Note If door swing is to be changed it must be done before panel is attached The panel will be held on by 6 sheet metal screws and 2 machine screws 1 Remove the gasket and retain for later use 2 Ifthe door panel is stainless steel remove any plastic covering the stainless steel panel 3 Place the panel onto the outside of the door and secure it to the door using two machine screws located at the left center and right center 4 Fasten the panel to the door using the 6 sheet metal screws In the hinge area use the outermost screw holes 5 Place the covers over the hinge areas and secure each cover to the door Custom Panel A custom panel of wood or other material not exceeding 15 lb can be attached to the door Attachment is from the ice side of the door Holes are provided in the door for this purpose See instructions in information packet to create and attach a custom panel using a sheet metal screw 6 Insert hole plug over screw installed in step 5 7 Return the gasket to its original position Hinge Area Cover November 2009 Page 7 SCCG30 amp SCCP30 User Manual Door Panel Attachment Use Upper Hole at the Top Scotsman Door Panel Gasket d Machine 7 i Screw dp Hole Plug Use Lower Hole at the Bottom Cover November 2009 Page 8 SCCG30 amp SCCP30 User Manual Door swing change Note Prior models had separate hinge
4. either from use or meltage November 2009 Page 12 SCCG30 amp SCCP30 User Manual Use No special instructions are needed for use Just take as much ice as you need the machine will replace it A scoop is provided and it can be stored in the machine using the loop of tubing on the right side as a holder What shouldn t be done Never keep anything in the ice storage bin that is not ice objects like wine or beer bottles are not only unsanitary but the labels may slip off and plug up the drain Never allow the machine to operate without regular cleaning The machine will last longer if it is kept clean Regular cleaning should happen at least once per year and preferably twice Some water conditions will dictate even more frequent cleaning of the ice making section and some carpets or pets will dictate more frequent cleaning of the condenser Noise The ice machine is designed for quite operation but will make some noise during the ice making cycle It is normal to hear the fan and circulating water during the freeze cycle and ice hitting the bin or ice in the bin can be heard during harvest If ice making noise is objectionable a timer can be added to the power supply Set the timer to turn the machine off at the time of day when the noise is most objectionable Maintenance There are 5 things to keep clean 1 The outside cabinet amp door 2 The ice storage bin 3 The condenser 4 The ice makin
5. All water including potable water supplied by municipalities contains some impurities or minerals Water absorbs impurities from the air as rain and or as it flows through the ground Some of the impurities are solid particles these are known as suspended solids and a fine particle filter will remove them Other impurities are chemically bonded to the water molecules and cannot be filtered out these are called dissolved solids Ice made by this machine will have a lower mineral content than the water it was made from This is due to the method of making ice Purer water will freeze first in the ice making molds The reason for this is that anything dissolved in water lowers the water s freezing temperature This concentrates most of the impurities in the ice machine water reservoir where they may form hard deposits known as scale The machine dilutes the concentration of minerals by over filling the reservoir during the harvest cycle with the excess water flowing down the drain About 3 quarts of water flow into the unit each cycle About 1 quart of that rinses the reservoir and goes down the drain Some impurities will inevitably remain and will stick to the parts in the machine and will cause malformed ice cubes Eventually built up mineral scale can shorten machine life To keep the machine operating properly these impurities or minerals will have to be regularly dissolved by an acid cleaning using Scotsman Ice Scale Remover
6. Pump Model drain installation 1 Locate the coil of 3 8 ID plastic drain tubing secured to the back of the unit 2 Route the plastic drain tube from the back of the unit to the drain connection point IMPORTANT NOTE Often an air gap is required by local codes between the ice maker drain tube and the drain receptacle Drain Tube Route to building drain Water Inlet Tube field supplied Back View Drain Pump Model September 2011 Page 10 SCCG30 amp SCCP30 User Manual Gravity Drain Caution Restrictions in the drain system to the machine will cause water to back up into the ice storage bin and melt the ice Gravity drain tubing must be vented have no kinks and slope to the building drain Air gaps are typically required by local code 1 Place the ice machine in front of the installation opening Adjust leveling legs to the approximate height 2 Remove the front service access panel and the upper back panel Note If you are connecting a gravity drain model and the drain opening has been located in the floor under the base pan according to the pre install specifications follow steps 3 through 5 to drain the unit through the base If not proceed to step 6b 3 Remove the clamp and barbed elbow and take off the plastic cover in the base pan below the drain hose 4 Connect a straight 5 8 barbed connector to the drain hose securing with the clamp removed in st
7. Scotsman Installation and Ice Systems User s Manual for Residential Ice Machine Models SCCG30 and SCCP30 SCCG30 amp SCCP30 User Manual Introduction This ice machine is the result of Scotsman s decades of experience in the design and manufacturing of both commercial and residential ice machines This manual includes the information needed to install start up and maintain the ice machine Note any Caution or Warning indicators as they provide notice of potential hazards Keep this manual for future reference Table of Contents Specifications s s s s wa ee A ow ba ea Os NOM ee Cabimet Layout q isa oe bw os oe Ged se Boe eee Bae oS eS Dm CC Gravity Drain Ge eae ee ded ElechtiGal z 24 24 4 oe eta ee oe ee ee Be ee November 2009 Page 2 SCCG30 amp SCCP30 User Manual Specifications This ice machine is designed to be used indoors in a controlled environment Use outside of the listed limitations is misuse and will void the warranty Air temperature limits The ice machine will operate adequately within the limits but functions best in temperatures between 70 and 80 degrees F Minimum 50 degrees F Maximum 100 degrees F Water temperature limits Minimum 40 degrees F Maximum 100 degrees F Water pressure limits e Minimum 20 psi Maximum 80 psi
8. brackets and different directions to change swing Moving the hinges allows the door to open from either the left or right side Change swing before attaching door panel To change 1 Remove innermost screw holding each hinge to cabinet loosen the other 2 Slide door to the side and remove from cabinet Pocket Cover Plug 3 Remove plug and hinge pocket covers from door Note There are either plugs or screws in the holes where the hinges will mount They must be moved 4 Remove hole plugs or screws from unit s new hinge locations set aside 5 Move screws loosened in step 1 to opposite location 6 Install screws or plugs removed in step 4 to the unit s original hinge location to fill the holes 7 Remove the upper hinge from the door and move it to the door s opposite side bottom location Secure using the original screws Note If door panel is attached it must be removed to access hinge screws and to reverse handle position 8 Remove the original lower hinge and move it to the door s opposite side upper location Secure using the original screws 9 Install pocket covers and hole plugs onto door 10 Attach the door to the cabinet using the original Screws Installation Notes Built In Situations If a finished floor is to be installed in the area after the ice machine has been built in shims the expected thickness of the floor should be installed under the unit to keep the machine l
9. e adds 1 5 8 Height 14 7 8 22 22 3 4 33 3 8 to 34 3 8 November 2009 Page 3 SCCG30 amp SCCP30 User Manual Cabinet Layout FLOOR DRAIN ue ACCESS HOLE 203 8 147 8 AIR OUT AIRIN m 75 SHEET METAL DOOR FRONT 63 MIN CABINET DOOR 291 4 333 MN 343 8 MAX 23 4 1 LEG ADJUSTMENT 4 PLACES November 2009 Page 4 DRAIN FLEXIBLE TUBING 3 8 L D PUMP MODEL INCLUDED 5 8 1 GRAVITY MODEL NOT INCLUDED POTABLE WATER INLET 1 4 COMPRESSION FITTING 115V POWER CORD SCCG30 amp SCCP30 User Manual Air flow The machine takes in room temperature air at the lower right front and discharges warm air from the lower left front Restricting the airflow will adversely affect the ability of the ice machine to make ice Warm Air Out Air Intake Scotsman Ice Systems are designed and manufactured with the highest regard for safety and performance They meet or exceed the standards of agencies like U L Scotsman assumes no liability or responsibility of any kind for products manufactured by Scotsman that have been altered in any way including the use of any parts and or other components not specifically approved by Scotsman Scotsman reserves the right to make design changes and or improvements at any time Specifications and designs are subject to change without notice November 2009 Page 5 SCCG30 amp SCCP30 User Manual Water Quality
10. ep 4 5 Cut an 8 piece of 5 8 ID X 7 8 OD tygon clear plastic tubing Slide one end of the tube onto the outlet of the barbed connector and secure with a clamp Leave the other end of the tube lying on the floor of the base pan until the unit is positioned over the floor drain 6 Route the drain tube Either a Insert the drain tube through the base pan into the floor drain or b Route the drain tube through the left hole in the lower back panel and connect to barbed elbow and secure with a clamp 7 Reinstall the upper back panel 8 Reinstall the service access panel Level the unit IMPORTANT NOTE Often an air gap is required by local codes between the ice maker drain tube and the drain receptacle Drain Hose Drain Hose Route to building drain Barbed Elbow Water Inlet Tube field supplied Back View Gravity Drain Model November 2009 Page 11 SCCG30 amp SCCP30 User Manual Electrical The ice machine is supplied with a power cord Do not remove the grounding pin from the cord s plug Do not use extension cords Follow all codes Connect the machine to its own 115 volt 15 amp circuit 1 If the electrical outlet for the ice maker is behind the unit plug in the unit 2 Position the unit in the installation opening 3 Turn on the water supply Make sure that the ice maker is plugged in and the power is on 4 Slide unit into installation opening payi
11. evel with the planned floor level Installations on a slab Use a pump model and pump the water to the point of drainage Pump models will pump 1 story 10 feet high Installations over a crawl space or basement Either gravity drain or pump model units may be used if there is not enough room behind the machine for a drain waste receptacle the drain will have to be below the floor Note When installed in a corner the door swing may be limited due to handle contact with the wall or cabinet face January 2012 Page 9 SCCG30 amp SCCP30 User Manual Water ___ Water Supply all models The recommended water Note Do NOT connect water to tubing in the back supply tubing is 74 inch OD copper Stainless steel flex or reinforced PVC tube may also be used Install an easily accessible shut off valve between the supply and the unit This shut off valve should not be installed behind the unit Note Do not use self piercing type valves 1 Remove the front service panel Screw Securing Front Service Panel 2 Route the tubing through the right hole in the back to the inlet water solenoid valve inlet in front 3 Install a compression fitting on the tubing and connect to the inlet of the solenoid of the unit Water supply connects in the front Drains There are two types of ice machine models one that drains by gravity and one that has an internal drain pump Drain
12. g system 5 The ice scoop How to clean the cabinet Wipe off any spills on the surface of the door and handle as they occur If anything spilled on the door or gasket dries onto the surface wash with soap and warm water to remove How to clean the ice storage bin The ice storage bin should be sanitized occasionally It is usually convenient to sanitize the bin after the ice making system has been cleaned and the storage bin is empty A sanitizing solution can be made of 1 ounce of household bleach and two gallons of hot 95 F 115 F water Use a clean cloth and wipe the interior of the ice storage bin with the sanitizing solution pour some of the solution down the drain Allow to air dry November 2009 Page 13 SCCG30 amp SCCP30 User Manual How to clean the condenser The condenser is like the radiator on a car it has fins and tubes that can become clogged To clean 1 Remove the kickplate 2 Locate the condenser surface 3 Vacuum the surface removing all dust and lint Caution Do not dent the fins 4 Replace the kickplate Winterizing 1 Clean the machine as explained on the next page 2 Open the door and switch the machine off 3 Turn off the water supply 4 Drain the water reservoir by removing the rubber cap on the back wall of the ice storage bin 5 Disconnect the incoming water line at the inlet water valve 6 Switch the machine to On 7 Blow air through the inlet
13. ng careful attention to water supply and drain connections Do not kink 5 Pour a couple of quarts of water into the ice storage bin on units equipped with a drain pump the drain pump should start and water should pump out Check for leaks and proper draining 6 Replace the service access panel Level the unit as needed Installation check list Has the unit been connected to the proper water supply Has the water supply be checked for leaks Has the unit been connected to a drain Has the drain been tested for flow and leaks Has the unit been connected to the proper electrical supply Has the unit been leveled Have all packing materials been removed from the machine Has the door covering been installed Initial Start Up 1 Turn on the water supply 2 Switch on the electrical power 3 Switch the on off switch to On The compressor will start and water will begin to flow into the unit When the reservoir is full water will start to drain from the machine After a few minutes the water pump and fan motor will begin to operate and the first ice making cycle will have begun No adjustments are needed After about a half hour ice will fall into the ice storage bin The first batches of ice will melt this is normal It will take 24 to 36 hours of continuous run time to fill the ice storage bin When the bin is full of ice the ice machine will shut off It will automatically restart when the ice level falls
14. ods Parkway Vernon Hills IL 60061 800 726 8762 www scotsman ice com 17 3191 01 Revised January 2012
15. water valve until water stops flowing from it a tire pump could do the job 8 Drain pump models should have about 1 2 gallon of RV antifreeze propylene glycol poured into the ice storage bin drain Note Automotive antifreeze must NOT be used 9 Switch off and unplug the machine How to clean the ice making system 1 Scoop out all of the ice either discard it or save it in a ice chest or cooler 2 Pour 8 ounces of Scotsman Ice Machine Scale Remover available from a local Scotsman Distributor or Dealer into the ice machine reservoir 3 Allow the machine to operate for about 2 hours 4 Pour hot 95 F 115 F water into the bin to melt the ice that has formed That ice will likely be white and frosty looking 5 Clean the bin liner of mineral scale by mixing some ice machine scale remover with hot water and using that solution to scrub the scale off of the liner 6 Rinse the liner with hot water 7 Sanitize the bin interior 8 Replace the ice removed in step 2 The ice scoop should be washed regularly wash it just like any other food container What to do before calling for service Ice cubes are incompletely formed Clean the ice making system Low capacity Check for restricted drain or standing water in the bin Clean the air cooled condenser fins No ice Check on off switch Check electrical breaker Check water supply November 2009 Page 14 SCOTSMAN ICE SYSTEMS 775 Corporate Wo
Download Pdf Manuals
Related Search