SP1091LX - Hayward
Contents
1. Min mm GPM Liter Min mm GPM Liter Min 20 1 45 PA 110 75 50 170 75 415 30 2 80 3 160 110 63 300 90 600 USE ONLY HAYWARD GENUINE REPLACEMENT PARTS Bs i HAYWARD Pool Products www haywardpool com a A Hayward Industries Inc Company Page 2 of 4 DYNA SKIM SKIMMERS IS1091LX REV D AN WARNING Read and follow all instructions in this owner s manual and on the equipment Failure to follow instructions can cause severe injury and or death IMPORTANT SAFETY INSTRUCTIONS A WARNING Suction Entrapment Hazard Suction in suction outlets and or suction outlet covers which are damaged broken cracked missing or unsecured can cause severe injury or death due to the following entrapment hazards Hair Entrapment Hair becomes knotted or snagged in an outlet cover Limb Entrapment A limb sucked or inserted into an opening of a circulation outlet with a broken or missing cover in the pool resulting in a mechanical bind or swelling Body Suction Entrapment Suction applied to a large portion of the body or limbs resulting in an entrapment Evisceration Disembowelment Entrapment Suction applied directly to the intestines through an unprotected sump or suction outlet with a missing or broken cover Mechanical Entrapment Potential for jewelry swimsuit hair decorations finger toe or knuckle to be caught in an opening of an outlet or cover To Reduce the risk of Entrapment Haz2. is not installed on the body it must be assembled to the body prior to attempting to install the skimmer in the pool To install the wide mouth extension insert four 4 pan head screws 1 long through the lip of the extension and four 4 through the throat of the skimmer Place the gasket between the extension and the skimmer body Firmly tighten the screws SKIMMER INSTALLATION From the outside of the pool install the face plate double gasket at skimmer cutout in the wall Reach over the top rail of the pool and carefully press the face plate and liner against the gasket and skimmer cutout in the wall Punch out the two top corner holes using a blunt object Insert two self threading flat head screws provided into the top corner holes of the face plate Carefully push the screws through the holes that have been pierced in the liner and through the double gasket From the outside of the pool align the skimmer body with these screws Lightly tighten the two screws Using a blunt object pierce the remaining holes in the liner Insert and lightly tighten the remaining flat head screws through the face plate liner gasket and into the corresponding holes on the skimmer Firmly tighten all screws evenly alternately left and right top and bottom Using the skimmer face plate as a guide use a razor knife to trim only the liner being careful not to the gasket in the large skimmer opening USE ONLY HAYWARD GENUINE REPLACEMENT PARTS HAYWARD Pool
3. PN ISIO9ILX REV D Owners Manual OWNER S MANUAL INSTALLATION OPERATION amp PARTS SP1091 SERIES DYNA SKIM AUTOMATIC SKIMMER AND HYDROSTREAM RECIRCULATION SYSTEM SP1091LX SP1091WM Your new Hayward Thru Wall Skimmer makes pool maintenance easier and more convenient Leaves insects and floating debris are pulled from the pool into the skimmer basket Clean the basket regularly to keep your pool sparkling clean and sanitary Basic safety precautions should always be followed including the following Failure to follow instructions can cause severe injury and or death AY This is the safety alert symbol When you see this symbol on your equipment or in this manual look for one of the following signal words and be alert to the potential for personal injury AY WARNING warns about hazards that could cause serious personal injury death or major property damage and if ignored presents a potential hazard AY CAUTION warns about hazards that will or can cause minor or moderate personal injury and or property damage and if ignored presents a potential hazard It can also make consumers aware of actions that are unpredictable and unsafe The NOTICE label indicates snecial instructions that are imnortant but not related to hazards MAXIMUM RECOMMENDED SYSTEM FLOW RATE BY PIPE SIZE Pipe Size Flow rate Pipe Size Flow rate Pipe Size Flow rate GPM Liter
4. Products www haywardpool com A Heyward Industries Inc Company Page 3 of 4 DYNA SKIM SKIMMERS IS1091LX REV D RETURN FITTING INSTALLATION 1 The return fitting furnished with these skimmers is a SP1023 The hole required through the pool wall to install this fitting is 2 38 03 inches DO NOT CUT THE LINER 2 Place one rubber gasket over the threads of the return fitting adapter and push the threaded end against the liner and through the return cutout in the wall 3 Applying outward pressure to the return fitting cut and X in the center of the exposed liner from outside the pool The return fitting will now be fully pressed against the liner and the wall on the inside of the pool Using a razor knife trim the excess liner material from around the fitting threads on the outside of the pool 4 Place the second rubber gasket and then the cork gasket over the threads of the return fitting now exposed outside of the pool Screw on the lock nut and tighten 5 Screw on the adjustable directional ball fitting into the face of the return fitting from the outside of the pool Position ball fitting opening away from skimmer opening Do not over tighten Note On going leaks from the skimmer or wall fittings may cause pool wall damage that eventually may result in pool wall failure RECOMMENDED WINTERIZING PROCEDURE Drain pool level approximately six inches 6 below skimmer opening Remove Hydrostream Eyeball fitting and securely plug wa
5. ards o A minimum of two functioning suction outlets per pump must be installed Suction outlets in the same plane i e floor or wall must be installed a minimum of three feet 3 1 meter apart as measured from suction center line to suction center line o Dual suction fittings shall be placed in such locations and distances to avoid dual blockage by a user o Dual suction fittings shall not be located on seating areas or on the backrest for such seating areas o The maximum system flow rate shall not exceed the flow rating of any listed per ASME ANSI A112 19 8M 1987 ASME A112 19 8 2007 suction outlet cover installed o Never use a Pool or Spa if any suction outlet component is damaged broken cracked missing or not securely attached o Replace damaged broken cracked missing or not securely attached suction outlet components immediately o Two or more suction outlets per pump should be installed in accordance with latest APSP Standards and CPSC guidelines follow all National State and Local codes applicable o Installation of a vacuum release system which relieves entrapping suction is recommended POOL PREPARATION Fill the pool with approximately two 2 feet of water so the liner is under weight and stretched to the proper position prior to installing the skimmer Note The liner cannot be shifted after the skimmer and return holes have been cut l PA SKIMMER ASSEMBY If the SP1091E Wide mouth extension
6. ll fitting 1 2 threaded plugs are available from the dealer Disconnect filter hoses from the skimmer and the wall fitting Be sure that the skimmer is kept free of water accumulation Warranty does not include damage caused by the formation of ice in the skimmer OPERATING INSTRUCTIONS TO CLEAN SKIMMER BASKET TO VACUUM WITH SKIM VAC Remove top cover or fold weir forward and squeeze tabs 1 Remove weir from front of skimmer toward center to remove weir Remove and clean basket 2 Attach vacuum hose to vac head and handle and fill Deluxe Skim Vac Accessory vacuum hose with water place over pool inlet Place SKIM VAC attaches to vac hose and is inserted in skimmer SKIM VAC over skimmer basket Going through the over basket allowing you to conveniently vacuum through the skimmer opening in the pool wall attach the vacuum hose skimmer basket to the SKIM VAC hose adapter 3 Hold SKIM VAC in place until any air hose is evacuated by pump Once air is removed the pump suction will dalk hold the SKIM VAC firmly in place lees TLL EEE fiam my TO PUMP amp FILTER Note Take care not to damage or scuff the SKIM VAC s specially designed sealing surface USE ONLY HAYWARD GENUINE REPLACEMENT PARTS a i HAYWARD Pool Products www haywardpool com fa A Hayward Industries Inc Company Page 4 of 4 DYNA SKIM SKIMMERS IS1091LX REV D NO ee aes DESCRIPTION REQUIRED Skimmer Body Not 1 procurable as a pa
7. rt 1 2 1 3 1 4 1 5 1 sone EE 6 SPX1091G Gasket 1 Widemouth i Extension Screws 1 Set Procurable only with Included in 8 SPX1090Z7A Item 11 pon ame 9 SPX1091GW Gasket 1 exe ae 10 SPX1091F Plate 1 Face Plate Screw Pack Includes 11 SPX1090Z7A screws for extension 1 Set rera Pan DESCRIPTION REQUIRED procurable as a part 1 pereg B 1 3 spito041 1 Le hoi C Basket w Handle 1 5 _ SPX1091K1 1 Standard Butterfly 091G Gasket 1 42 spxt091 D Face Plate 1 Face Plate Screw SPX1090Z6A Pack 1 Set M HAYWARD Pool Products A Hayward Industries Inc Company USE ONLY HAYWARD GENUINE REPLACEMENT PARTS Pomona CA Nashville TN North Kingstown RI St Vulbas France Clemmons NC Wuxi China Oakville ON Canada www haywardpool com
Download Pdf Manuals
Related Search