Home

V-Series Dobby Loom User`s Manual

1. INSTALL THE HARNESSES AND SPRINGS see Figure 3 15 4 5 6 7 V SERIES LOOM ASSEMBLY Thread 50 heddles onto the sticks we provide 50 heddles per harness plus 200 extra Move all of them to the center positioning two at each of the outer ends of the sticks Select two harness wires and slide one through the end hole of the top stick so that the copper fitting at the end of the harness wire is at the top Insert the blank end of the wire through the end hole of the bottom stick Add the second harness wire Move one heddle out to either end of the harness immediately adjacent to the harness wire These two heddles will be helpful in maintaining the rectangular shape of the harness until and after it is hung in place If you wish to save space by mounting each harness as it is assembled proceed to the next section now for instructions on hanging the harness and installing the springs The Harness Pulley Support has a top that serves as a shelf and slides out to give you access to the pulleys If you have not done so by now please remove the shelf by pulling the pin in the center rear Harness Pulley Sup port and sliding the shelf out to one side 8 9 Locate the bundle of harness cables Remove the ties and select one You ll see that each cable has two terminal ends a long and a short each ending in a loop A small berkeley clip is mounted in the loop at the opposite end of the cable It will
2. WARPING THE SECTIONAL BEAM Page 5 2 Therefore we can say OF SPOOLS EPI x SIZE OF THE SECTION NUMBER OF YARDS PER SPOOL To calculate the number of yards per spool we need to know the LENGTH OF THE WARP NUMBER OF SECTIONS on the Beam We calculate the number of sections by dividing the WIDTH OF THE WARP by the SIZE OF THE SECTION Ifthe warp width is 30 and we are using 2 sections our number of Sections is 15 All together we can say OF YARDS PER SPOOL LENGTH OF THE WARP x OF SECTIONS TOTAL YARDAGE If it is a single color warp or if a color sequence is repeating in each section the same spools or cones can be used to wind all the sections needed for the warp TOTAL YARDAGE OF SPOOLS X OF YARDS PER SPOOL It is important to make these calculations in advance so that you can purchase your yarn in spools or cones cor responding to the amount of yardage needed on each Sometimes this is not possible and you will need to wind your own spools from yarn that is in larger packages For doing this you will need empty plastic spools a bob bin winder preferably electric and a yardage counter These items are available from AVL V SERIES WARPING THE SECTIONAL BEAM EXTENSION CORDS FEEDING THE SPOOL RACK You might want to make a permanent set of Extension Cords to use when warping the Sectional Beam Exten sion Cords are also called apron cords and serve the same funct
3. SERVICE Page TOC 4 Figure Attaching Yardage Counter to Tension Box Creating the Cross Inserting Sticks in the Threading Cross Readjusting the Tension Combining Sectional and Plain Warping Preparation for Threading Threading the Harnesses Unused Heddles Sleying the Reed Tying On to the Apron Figure Warp Routing Figure Tying On to An Old Warp E Lift II Brake System Cloth Storage System Removable Breast and Separation Beam Swinging Beater Sectional Beam Plain Beam Dobby Head and Compu Dobby Harness Springs Harnesses Table 1 Harnesses Tightening the Bolts Lubrication and Cleaning Cleaning the E Lift Filters Checking Cords and Cables Tool Kit and Spare Parts AVL Warranties AVL Returns Policy OY OV OV OY OY OF OY OD a 1 1 BRARWNNNF KB te ee ee NNN UBRWWWNNNF KB ABOUT AVL THE V SERIES DESIGN CONCEPT V SERIES INTRODUCTION AVL Looms has been in the business of designing and building some of the world s finest handweaving looms since 1976 Jon Violette the V in AVL initiated Ahrens and Vio lette Looms when he approached Jim Ahrens about a partnership in 1977 Mr Violette an industrial manage ment professional had discovered Ahrens work through his sister who ran the Pacific Basin School of Textiles in Berkeley where Ahrens was a volunteer advisor The two men worked together in the Bay Area for three years until Violette moved the business to Chico where it
4. section of the raddle In the Threading Cross each thread crosses the next thread in opposite directions and all are secured in a sin gle loop at the axis of the cross The number of threads in a Raddle group can be determined by the number of ends to be placed in each section of the Raddle Before removing the warp from the board or the reel secure the crosses Use four ties to secure each cross in addition to the tie at the cross axis These ties go on each side of both pegs holding the cross It is usually a good idea to use different color threads for the ties on the tops of the pegs and another color to tie the bows underneath the pegs By color coding your ties you are less likely to twist the warp later Remove the warp from the warping board by chaining or by winding on the kitestick Start from the Threading Cross and proceed to the Raddle Cross Since the capacity of the warping board is limited for wide warps you will end up making a number of mini warps and taking them off individually In Chapter 3 you installed the Brake Tension Device Before winding on the warp there are a few small things to take care of on the loom First check the tension device to make sure the rope is wrapped three times around the tension drum and that the rope end is clipped to the spring which is held by the Hook Bolt Test that you are able to turn the Beam in a clockwise direc tion If this proves difficult you can let some leng
5. through the race and into the two corresponding holes in each Beater Leg Attach the washers and nuts and tighten only slightly Repeat this procedure for the other side of the loom making sure that the tapered side of the leg is always facing away from the loom At tach the washers and nuts leaving them loose for the moment Center your reed in the slot Now orient your Beater Top so that the groove is facing down and the cut outs at either end are fac ing toward the rear of the loom Insert 1 4 x 2 carriage bolts into the holes located at each end starting them from the front Placing the Beater Top over the race and reed slide the bolts into the slots at the top of the Beater Legs and once the reed is securely inside the groove in the Beater Top attach the washers and wing nuts and tighten them to hold but wait for adjustment in the next step before tightening fully Page 3 25 V SERIES LOOM ASSEMBLY INSTALL THE WARP BEAM S see Figure 3 17 Page 3 26 11 Center the Beater Assembly in the loom a Place a level in the center of the race and ad just the height of each side using the black adjustment knob at the metal plate on the Beater Support These enable you to raise or lower the race on either side to ensure the race is level b Once the race is level holding the Beater Top at its center and push the Beater all the way back to meet the Beater Bumpers Ensure that both sides of the Beater are touc
6. Central Support Cross Member 18 SUPPORT CROSS MEMBER 18 see Figure 3 11 SQUARING THE COMPLETED FRAME and prepare two mounting bolts with washers and square nuts for mounting 2 Position this Cross Member as follows a Between 3 and 12 b At the two holes located just above the Front Spring Cross Member 19 C With the access holes at either end pointing to the back of the loom d This will place 12 directly over the access hole for the second bolt that secures the Spring Support in place 3 Insert the bolts with washer from the outside through the ends and secure with the nuts Tight en securely 4 One more set of Cross Members and you ll be hanging the Dobby then the beater and harnesses Soon you ll be finished Now that you have completely assembled the Loom Frame it is time to assure that the frame is square and level Tightening of all bolts for the Frame Sides and Cross Members has been put off for this procedure Please make a note of this process as it is an impor tant part of the maintenance of your loom The many features of this loom will perform better and give more years of service if this process becomes a part of your regular loom maintenance 1 Using a tape measure note these measurements a The distance from the inside corner of the Rear Left Vertical 5L to the inside corner of the Front Right Vertical 2R b The distance from the inside corner of the Rear Righ
7. Lift Support Mount Block Continue pulling on the cord toward the left side of the loom Loop the cord under the pulley mounted on the lever and bring it over the pulley back to ward the center of the loom With one hand maintaining tension on the cord grasp the bottom of the lever with the other hand and pull it against the spring tension back toward the loom center Take care not to pinch fingers be tween the spring and the lever Use the slack cre ated in the cord to extend it back toward the right side of the loom and the waiting eye bolt Now that the cord and cables are installed it is time to check that the Cam and pulleys are aligned to allow for smooth vertical movement Use an allen wrench to tighten all six lock collars securely in place please refer to Figure 3 5 The Cam and pulleys should be allowed to turn freely but with out and lateral wiggle Locate and connect the foot switch cord to the front of the E Lift II Connect the female end of the power cord at the back of the housing be sure it s completely inserted Turn off the E Lift II power switch Plug the male end of the power cord into a good quality surge protected power strip preferably the same one as used for your Compu Dobby as this will allow you to turn on the loom more easily Page 3 35 V SERIES LOOM ASSEMBLY SETTING THE HOME POSITION SELECTION OF SINGLE OR DOUBLE ACTION MODE REQUIRED MAINTENANCE FOR THE E LIFT II P
8. They are drilled completely through the frames Locate the Cloth Storage Beam It has a metal ratchet on one end Find too the Cloth Advance Handle You ll see that the Advance Handle has an oblong hole at one end Fit this hole over the Cloth Stor age Beam Axle next to the ratchet with the black handle pointing to the interior of the loom INSTALLATION OF THE CLOTH STORAGE BEAM Page 3 9 V SERIES LOOM ASSEMBLY INSTALL THE LOWER FRONT CROSS MEMBER 16 see Figure 3 9 Page 3 10 4 5 6 7 1 2 3 Now with the Handle Assembly to the right side gently ease the two Side Frames apart and slip both ends of the Beam into their mounting holes Allow the handle to rest atop the small block in stalled in the Right Side Frame Be sure to hold the Cloth Storage Pawl out of the way when in stalling the Beam Screw this assembly into place in the pre drilled hole and tighten securely Push the side frames together CAUTION Until the Lower Front Assembly is installed take care not to dislodge the Beam Locate the Lower Front Assembly Cross Member 16 and Hardware Select four hex bolts and remove the nuts Identi fy the Lower Front mounting holes on the diagram located at the base of 2R and 2L Move again to the front of the loom this time pivot it away from you and lay it on its Rear Verti cals You may want to rope the two sides together near the Cloth Storage Beam to le
9. You ll need occasionally to clean the air filter which is located on the front of the E Lift II housing To clean unsnap and remove the plastic baffle Remove the foam element and carefully wash it in warm soapy water Be sure the element is completely dry before you replace it SUGGESTED MAINTENANCE FOR THE E LIFT II V SERIES LOOM ASSEMBLY The E Lift II Pulley Cam pulley to slide plate and coun terweight cables may stretch with extensive use If after setting your Home position you find that the counter weight is hitting the floor with the shed open this is like ly the cause To adjust simply push the cable through the Cam Pulley and re tie the knot to a shorter length For the counterweight cable tie a knot in the cable at a location where it won t run over a pulley in normal op eration Inspect the cables for wear especially where they move over a pulley Do this monthly if you weave regularly Check the supporting hardware and re tighten if loose Your E Lift II is designed to provide years of dependable service When replacement parts such as the air filter or cables are needed AVL is your source AVL can also rebuild your E Lift II when it reaches the end of its wear cycle Please contact us at 530 893 4915 or info av lusa com to place your order or to arrange service INSTALLATION OF 1 Take the Compu Dobby from its protective box and have the four thumbscrews free from the Dobby Back and at hand for this
10. installation THE COMPU DOBBY see Figure 3 13 for parts and placement FIGURE 3 21 SOLENOID TIPS ALIGNED CORRECTLY 2 Check to see that all of the little black plastic tips on each solenoid appear concave when viewed from above They can be easily turned with a slight touch see Figure 3 21 Page 3 37 V SERIES LOOM ASSEMBLY Page 3 38 3 4 5 6 7 8 9 Before proceeding further locate the four mounting holes in the narrow sides of the Dobby Back Be hind each hole seen from the interior loom there is what appears to be the head of a standard slot ted screwdriver This is the end of the barrel nut that will secure the tip of each thumbscrew Be sure these slots are aligned horizontally Use a screwdriver to rotate them into place Bring the Compu Dobby up to the Dobby Back and align the four mounting holes located on the edge of the sides with the four holes on the sides of the Dobby Back The Compu Dobby is heavy and must be grasped and supported from the bottom We suggest using a pot holder or pad to make this more comfortable on your hands Align the four sets of holes and insert one thumb screw into each Wait until all are installed before tightening completely Prior to tightening press the Compu Dobby flush against the loom castle There is a little bit of play in the holes and the solenoids will perform best if they are positioned correctly Attach the power cable to th
11. matter whether you go top to bottom or bottom to top the important thing is to be consistent in vertical columns and to place the spools in the order that the threads are in the warp Page 5 3 V SERIES WARPING THE SECTIONAL BEAM THE TENSION BOX This is an essential tool for Sectional Warping which TENSION BOX HEDDLE INSTALLATION INSTRUCTIONS Page 5 4 1 Puts threads under even tension 2 Spreads threads to the proper width of the section 3 Makes a thread by thread cross If this is your first time to use a Tension Box you need to install heddles on the harnesses of your Tension Box Your Tension Box is delivered with one bundle of one hundred heddles These are held together with twist ties Leave these on for now Refer to the upcoming di agram to familiarize yourself with the Tension Box and its parts Push down on one of the harnesses until it stops This causes the other harness to go up You will use that later for making a Threading Cross Right now we ll need to use it to help in the assembly of the heddles to the harnesses 1 Remove the heddle retainer of the harness that is up using a phillips head screwdriver 2 Notice there are four twist ties holding the heddles together Separate the top two Insert the top bar of the harness that is up into the space created by pulling apart the twist ties Insert the bottom bar of the harness that is up into the space cre ated by pulling apart t
12. of finger Rearrange the cables according to slots the assembly instructions D Harnesses don t raise prop 1 Harness cables have been Rearrange the cables erly hooked to the wrong harness 2 Chains from the spring Rearrange the cables levers have been hooked to the wrong harnesses 3 Copper hooks on the Straighten the hooks with pliers spring levers have been bent E Harnesses jam up on each 1 Heddles are not distrib Redistribute the heddles evenly on other uted evenly over the harness both sides from the center of the sticks harness sticks 2 Harness wire that con nects the harness sticks has jumped out and got stuck in the heddles of the other har Pull the wire out make sure it does not catch any heddles and replace it to just connect the top and the bot tom harness sticks ness If you have a large number of extra heddles on each side you might want to tie them in bundles to pre vent getting caught by the harness wires Page 7 5 V SERIES LOOM MAINTENANCE TIGHTENING THE The single most important thing you can do to extend BOLTS the life of your loom and preserve its operation is tighten the bolts that hold its frame together These will loosen over time due to changes in its environment and to your own creative exertions A loom which is allowed to become loose jointed will certainly cost you weaving time perhaps affect the quality of your work and defi nitely become olde
13. officially became known as AVL Looms Inc and has operated ever since In 1982 Mr Violette was instrumental in the develop ment of the first computerized dobby then called the Apple Dobby He retired from active life in the compa ny in 1987 We have christened this new V Series Loom in recognition of Jon s contribution to handweaving Over the years many people from customers to staff have offered suggestions that have helped us improve our products Once known for our production looms AVL has broadened its line considerably and we now offer customers a full spectrum of fine weaving equipment ranging from our small Home Looms to our Industrial Dobby Looms Rug Looms and Jacquards We wanted to design a loom with a dynamic mix of simplicity and sophistication a no frills approach for weavers who want complex weaving capability in a more fundamental package We ve streamlined this loom so you get a lot of harnesses and strength on a small rug ged loom Page 1 1 RECEIVING YOUR NEW LOOM SHIPPING DAMAGE ASSEMBLED OR NOT V SERIES SET UP If your loom was assembled by AVL it will have arrived on a pallet Looms delivered outside the continental U S will probably be further contained within a protec tive framework Accessories too large to include with the loom will be located in supplementary boxes Looms delivered knocked down will arrive in several large and small boxes Please confirm that
14. on top of the top horizontals 10 and 15 so that the end with the two rows of pulleys is at the right side of the loom and the small plaque with your loom s serial number facing to the front of the loom It should overhang about 4 on the right side as shown in Figure 3 12 Fig 3 12 4 5 6 7 V SERIES LOOM ASSEMBLY MOUNTING THE HARNESS PULLEY SUPPORT ASSEMBLY HARNESS PULLEY SUPPORT MOUNTING HOLE SIDE VIEW FRONT VIEW Align the four mounting holes in the Pulley Sup ports with those in the Top Horizontals If you are not able to align the holes without removing the packing strips take extra caution to move the Horizontals into place without pulling them apart Cut and carefully remove the packing tape if you have not already done so From above insert the Flat Head Machine Screws into the four mounting holes punching holes in the plastic Now remove the plastic and add the square nuts Tighten securely Remove the top shelf held between 21 and 22 by pulling the retainer pin located at the back of the rear Harness Pulley Support and sliding the board out to one side Set the shelf aside while the harnesses are mounted into place Page 3 17 V SERIES LOOM ASSEMBLY 8 Take a moment to breath and appreciate your progress You ve achieved something like the pinnacle of the assembly process Everything s a down hill coast from here INSTALL THE Your Compu Dobby is com
15. the hoop to the right Now tighten the wing nut under the pivoting reed This shouldn t need to be readjusted until you are using yarn of a very different size in another section 4 74 Extra care to correctly center and adjust the width of each warp section will result in more perfect tension while weaving Make sure that the threads are going on to the Beam in flat layers If you notice that warp piles up at the hoops the section of the warp is too wide If the warp falls down at the hoops the warp section is too narrow Page 5 9 V SERIES WARPING THE SECTIONAL BEAM COUNTING TURNS OR YARDAGE Page 5 10 If any of the above is happening gently unwind the warp into a box perhaps and pivot the front reed on the Tension Box again until you get perfectly flat layers This is very important otherwise you will end up having dif ferent length threads in one section since the circumfer ence of the Beam within the section is not going to grow evenly This uneven tension will end up causing lots of tension problems To determine the length of the warp you are putting on the Beam you need to count either turns revolutions or yards To count turns you can do it in your head but it is more reliable to use a digital or mechanical revolution counter Counting revolutions even with a digital counter will only give the approximate warp length because the circum ference of the Beam will increase slightly with each
16. tip of the bolt through the three strands of cord that create the loop with the toggle re maining above the pedal TENSION ADJUSTMENT FOR BRAKE PEDAL Fig 3 20 Page 3 31 V SERIES LOOM ASSEMBLY INSTALL THE SHELF Page 3 32 8 Push down on the end of the brake pedal so that you can attach the spring to the same bolt You ll have both the tie up and the spring on the bolt 9 Push the bolt back through the pedal and replace the nut 10 Hook the loop at one end of the cable on the proper J bolt Bring the cable immediately up and around the exterior side of the Brake Drum Wrap it around the Brake Drum it will pass over the top of the drum three times Take care not to cross the cable on itself 11 When you ve just enough cable remaining to al most reach the brake pedal collect the three loops of the cord into the snap hook 12 Check again to make sure the cable isn t crossed on itself 13 Use the toggle on the tie up to adjust the tension on the pedal To increase tension pull the two ends of cord away from the toggle as shown in Figure 3 20 To decrease the tension squeeze the buttons on either side of the toggle and move it up and down on the looped ends You re nearly finished it s time to install the shelf 1 Orient the shelf so that the felt strips on the bot tom will lay atop the three sets of Harness Pulleys when the shelf is in place These act as Cable Re tainers and will k
17. up and down on the cord This will allow you to turn the Beam backwards during winding while stabiliz ing the Beam when it is at rest Don t forget to retighten the cord before you begin threading the heddles Before you start winding the warp the Extension Cord must be attached to the Beam and the section of the warp to the Extension Cord First wind the tied end of the Extension Cord around the Beam Axle At the knot separate the two ends and pull the other end of the cord all the way through and tighten the Extension Cord around the axle oh TES aa TO ot THE WARP BEAM HANDLE IS TURNED CLOCKWISE SO THAT THE FIBER IS WOUND ONTO THE BACK OF THE BEAM WINDING ON THE WARP Page 5 8 V SERIES WARPING THE SECTIONAL BEAM ADJUSTING THE SIZE OF THE SECTION J Next tie an overhand knot near the end of the warp threads from one section and slip that knot into the opening of the larkshead knot you create in the Exten sion Cord Pull it tight Line up the Tension Box approximately over the section you will be winding Now slowly wind about one revolution onto the Beam As you wind you will need to fine tune the placement of the Tension Box along the track When it is centered properly tighten down the wing nuts under the Tension Box At this point you can pivot the pivoting reed sec tion so that the yarn comes close to but doesn t quite touch either the hoop to the left or
18. DLES Fig 3 17 3 Swing the retainers aside and position the Beam in place Bring the warp beam into position If you are using the upper location orient the beam so that the long end of the axle extends to the left of the loom opposite the Dobby Head 4 Seat the Beam in the axle pockets and holding the Beam in place rotate each retainer back down to safely secure the Beam 5 Locate the Warp Beam Handle and remove its hardware Page 3 27 V SERIES LOOM ASSEMBLY 6 Slip the handle over the protruding end of the Page 3 28 Beam Axle Insert the bolt and secure with the washer and nut Note that the handle is connected with a carriage bolt the head of which must fit into its stamped recess 7 Follow the same procedure to mount a second Lower Beam The Lower Beam should be oriented so that the handle is on the Dobby Side right hand side of the loom Remember a Sectional Beam can only be mounted in the upper location INSTALLATION OF THE SECOND SEPARATION BEAM BRACKETS SEPARATION BEAMS amp BREAST BEAM Invert this Beam to expose the slot for mounting a Tension Box CD optional To use Breast Beam for Separation Beam when using Tension Box move to slot in 6 optional INSTALLATION OF THE BREAST BEAM AND SEPARATION BEAM S BRACKETS FOR SECOND WARP SEPARATION BEAM see Figure 3 18 V SERIES LOOM ASSEMBLY Your package includes one Breast Beam and a Separa tion Beam for eac
19. E and PARTS A CHROME PLATED BOLT X 4 3 4 ASSY B CHROME PLATED BOLT X 3 1 4 ASSY C 1 4 X 5 1 2 HB ASSY 1 Bottom Horizontal 6 Mid Rear Horizontal 2 Front Vertical 7 Mid Front Horizontal 3 Middle Vertical 8 Handle Stop r 4 Castle 9 Top Vertical Support Fig 3 3 5 Rear Vertical 10 Top Horizontal 4 Locate the Cam Pulley Assembly Loosen the Lock Collars and withdraw all parts from the Axle Be sure to take these parts off in their precise order so that you can replace them exactly as they were shipped to you Page 3 4 V SERIES LOOM ASSEMBLY NOTE Make sure there isn t anything string tape lodging the Axle in the cam A F INSERTS HERE FE DOBBY CAM CYLINDER INSTALLATION RIGHT FRAME VIEW Fig 3 4 5 Insert the Axle from your left side into the mount ing hole in the front face of in part 3 see Figure 3 4 Push it through the hole until about 1 2 of the Axle is coming out the other side of 3 6 Rotate 3 about 20 degrees so that the free end of the Axle points to the outside of the loom and toward you Page 3 5 V SERIES LOOM ASSEMBLY 7 Thread the Cam Pulley Assembly and wooden pul ley back onto the Axle Do not tighten any of the Lock Collars at this time From left to right the parts should be mounted as follows a 1 Lock Collar b Right Side Frame 3 C 2 Lock Collars d 1 Cam Pulley Assembly e 2 Lock Collars f 1 Return Pulley g 2 Lock Co
20. OM ASSEMBLY Page 3 8 6 7 8 9 10 Locate the mounting holes for the Lower Back as shown in Figure 3 7 between Parts 1 and 11 Insert the four bolts in their holes but not so far that they protrude out the other side Position the Lower Back between the two Side Frames at the mounting holes and orient it so that the access holes are facing the floor when the loom is upright Push the bolts into the access holes at both ends of the Lower Back add the nuts and tighten to secure the bolt but not all the way Final tightening will occur when you square the finished frame The frame is now self supporting Put it back on its feet CROSS MEMBER MOUNTING HOLE LOCATIONS ___ HARNESS PULLEY SUPPORT 2 n MOUNTING HOLE HARNESS PULLEY SUPPORT CROSSMENBERS CROSSHEMBER E4IFT MOTORA MOUNT 4 SPRING SUPPORT CROSSMEMBERS i f LOWER PRONT CROSSMEMEER LOWER BACK CROSSMEMSER MOUNTING HOLES MOUNTING HOLES Fig 3 7 INSTALL THE CLOTH STORAGE BEAM see Figure 3 8 V SERIES LOOM ASSEMBLY The Cloth Storage beam MUST be installed at this point in the assembly process Its Axle fits into holes in the Side Frames and once the frames are joined further it will be impossible to add the beam refer to Figure 3 8 1 2 3 Locate the Beam mounting holes in each Side Frame These are about 1 in diameter and lay opposite one another in the Mid Front Horizontals 7 13
21. TENSION BOX Page 5 6 Mount the Tension Box in the groove with the Counter facing into the loom The Tension Box is fastened to the Separation Beam with a small cross piece and wing nuts This will stabilize the Tension Box and allow it to travel smoothly from one section to another The wing nuts can be released for the Tension Box to move easily from side to side Each time the Tension Box is moved and centered properly for a particular section the wing nuts must to be tightened again The best way to thread the Tension Box is to take one thread from the furthest left cone as you face the Cone Rack with your back to the loom and thread it all the way through all the parts of the Tension Box nearest to the back plate of the Box then the next thread all the way through It works best to use the threads from the rack in a vertical order rather than a horizontal order Now let s go through the sequence for threading the Ten sion Box First move the two adjustable Tension Pegs up above the Stationary Pegs or remove them complete ly Now using a sley hook draw the thread through the Rear stationary Reed Since this reed is eight dents per inch you will divide the E P I into eight to find out how many ends will be in each dent with sixteen E P I put two ends in a section If your E P I does not di vide equally by eight you can either vary the number of ends in each dent with twenty E P I alternate two and three ends in
22. V Series Dobby Loom User s Manual AVL Looms 3851 Morrow Lane Suite 9 Chico CA 95928 8305 U S A 530 893 4915 530 893 1372 fax info avlusa com www avlusa com Version 1 March 2010 V SERIES TABLE OF CONTENTS INTRODUCTION About AVL 1 1 The V Series Design Concept 1 1 SET UP Receiving Your New Loom 2 1 Shipping Damage 2 1 Assembled or Not 2 1 Unpacking an Assembled Loom 2 2 LOOM ASEMBLY Before You Begin 3 1 Tools 3 1 About Those Nuts and Bolts 3 2 Figure 3 1 Assembling Lower Left Back Corner 3 2 Left and Right Side Frame Assembly 3 3 Figure 3 2 Left Side Frame Hardware and Parts 3 3 Figure 3 3 Right Side Frame Hardware and Parts 3 4 Figure 3 4 Dobby Cam Cylinder Installation 3 5 Figure 3 5 Cam Pulley Assembly Installed Install the Lower Rear Cross Member Figure 3 6 Set Both Frames Side by Side on the Front Verticals 3 7 Figure 3 7 Cross Member Mounting Hole Locations 3 8 Install the Cloth Storage Beam 3 9 Figure 3 8 Installation of the Cloth Storage Beam Install the Lower Front Cross Member Figure 3 9 Install the Brake Pedal Figure 3 10a Brake Pedal Mounting Hardware lower beam position pedal to right hand side 3 12 Figure 3 10b Brake Pedale Mounting Hardware upper beam position pedal to left hand side 3 12 Install the E Lift Supports and Spring Anchor 3 13 Figure 3 11 Location and Installation of Crossmembers an
23. VL will generally return repair or replacement items via UPS Ground service Additional charges for expedited shipping are the responsibility of the customer Page 9 1
24. Wrench Medium Standard Blade Screwdriver 4 1 Screwdriver or Medium Phillips and Standard Screwdrivers 1 8 Allen Wrench Level Paste Wax 0000 Steel Wool Pad 220 Sandpaper Paraffin Wax Spare Parts You Might Consider Having Spare Treadle Cable left right 6 length of 350 Braided Dacron Cord for emergency repairs V SERIES AVL CUSTOMER SERVICE AVL WARRANTIES AVL RETURNS POLICY AVL offers free technical support to the original owner of all our looms This means if you ever have a problem you can call fax or e mail us and we ll help you find a solution Please take advantage of this service your satisfaction is extremely important to us Customer Service Phone 530 893 4915 Fax 530 893 1372 E Mail info avlusa com Your loom carries a full warranty on parts and labor for two years from the date we ship it to you Your Compu Dobby is fully warranted for two years If a part wears or breaks during this period we will replace or repair it at our discretion but at no charge to you All goods excepting software may be returned for re fund within thirty 30 days of the shipping date A 15 restocking fee will be assessed for all but defec tive items AVL will pay all shipping costs for defective items within the continental United States for the entire warranty period Special provisions apply for the return of looms please contact your sales person for more information A
25. age 3 36 Before you use the E Lift II you must set the home or neutral position 20 Turn off the E Lift II power switch Unwind the cord on the Motor Box Pulley and bring the Dobby Slide Plate to its upper most position 21 Rewind the Motor Pulley Cord making sure the Dobby Slide Plate remains at least approximately 1 4 above the ball on the rear most Dobby Cable or cylindrical crimp if you have Dobby Wires Turn on the E Lift II power switch You have now set your Home Position and may start to weave The E Lift II is programmed with two modes Double or Single Shed selection The Double Shed mode completes every lifting cycle with the shed open For example assume you ve just completed a shot and the shed is still open You depress the foot switch and the shed closes the Dobby advances to the next pick and the shed opens all as a single continuous movement You ll very quickly develop a rhythm and will find there s ample time to beat while the shed is transitioning between Open Close Open To use the Double Shed mode find the selector switch located at the rear of the E Lift II and set it to the On position see Figure 5 In Single Shed mode you activate the foot switch once to open the shed and again to close the shed In other words you achieve one action per activation If you wish to use the Single Shed mode ensure that the Dou ble Shed mode selector switch in the Off position
26. be easier to begin by hanging the rearmost harness and then mounting each in succession moving towards the front Take the Dobby Cable nearest to the rear of the loom Notice it ends ina small loop Page 3 21 V SERIES LOOM ASSEMBLY HARNESS SYSTEM WITH SPRINGS A HARNESS PULLEY SUPPORT E HEDDLES B HARNESS PULLEYS F HARNESS SPRINGS C HARNESS CABLES G SPRING HOOKS D HARNESS STICKS 18 F B E LIFT MOTOR SUPPORT 19 SPRING SUPPORT Fig 3 15 10 It will be necessary to squeeze the sides of the berkeley clip to expose the hooked ends and al low the insertion of the Dobby Cable loop into the hook You may wish to use pliers for this opera tion Once you have attached the Harness Cable to the Dobby Cable Lay the cable over the rearmost pulley at the right hand side Now orient the lon gest end of the cable over the pulley furthest from the Dobby and the shortest leg over the pulley in the middle set Page 3 22 V SERIES LOOM ASSEMBLY Check that the cable is not twisted on itself this INSTALL THE BEATER ASSEMBLY see Figure 3 16 11 12 13 14 15 will cause problems when you are weaving Take up the Harness Frame you assembled earlier Orient the frame so the hooks that are set closest together are at the TOP of the frame Hang the harness from the cable you just installed looping the two ends of the Harness Cables onto the eyehooks Locate two harness springs Fasten one
27. ck leaving one foot past the lease sticks and also use a half knot to tie bundles of yarn together for security After winding on the new warp on the Beam you can sit behind the loom on a small stool and tie correspond ing yarns from the two sets of lease sticks together An overhand or weaver s knot work well This may seem slow at first but you will work up a faster rhythm with some practice A good goal to reach would be to tie 200 to 250 ends together an hour When all ends are tied together go to the front of the loom and gently pull on the bundles of yarn going through the reed to pull the new warp through the hed dles and reed You may find that turning small bundles of the warp in a circular clockwise motion will help the through the heddles and reed Then tie on to the apron Page 6 5 E LIFT II BRAKE SYSTEM V SERIES LOOM CONTROLS 1 Power Switch 2 Double Action Switch 3 Cable Functions 4 Explanation works independently of the Compu Dobby Your V Series Loom is equipped with a locking brake system This means that the Warp Beam will be held absolutely captive will not release warp until you depress the Brake Pedal It s fairly foolproof and af fords very taut warps When your fell has moved as far forward as you re comfortable and you wish to advance your warp quickly depress the pedal with a short tap type motion and crank the warp forward with the Cloth Advance Handle You will hav
28. d Spring Support 3 14 Page TOC 1 V SERIES TABLE OF CONTENTS Page TOC 2 Install Central Support Cross Member Squaring the Completed Frame Install the Harness Pulley Support Assembly Figure 3 12 Mounting the Hardware Pulley Support Assembly Install the Dobby Back for your Compu Dobby Figure 3 13 Installation of the Dobby Head dobby back Install Harness Assemblies and Springs Make Texsolv Harness Assemblies Figure 3 14 Texsolv Heddle Installation Install the Harnesses and Springs Figure 3 15 Harness System with Springs Install the Beater Assembly Figure 3 16 Standard Beater Support Install the Warp Beam s Figure 3 17 Installation of Two Plain Beams and Handles Figure 3 18 Installation of the Second Separation Beam Brackets Separation Beams and Breast Beam Installation of the Breast Beam and Separation Beam s Brackets for Second Warp Separation Beam Mount the Brake Cable System Figure 3 19 Installation of the Brake Pedal Left Side Figure 3 20 Tension Adjustment for Brake Pedal Install the Shelf Installation of the E Lift II Install the E Lift II Motor Box Install the Cam to Motor Cable Install the Cam Cylinder to Slide Plate Cable Install the Spring and the Return Cord Completing Installation of the E Lift II Setting the Home Position Selection of Single or Double Action Mode Required Maintenance for the E Lift II V SERIES TABLE OF CONTENTS Suggested Maintenance
29. e Compu Dobby at the plug by the power Switch located on the lower front of the unit Attach male end of the beige RS 232 serial cable at the female connection on the lower front of the unit and the female end of the cable to the male serial port on your computer or using a high speed serial adapter to a USB port on your computer Please refer to your weaving software manual for further information about the computer interface with your Compu Dobby V SERIES WARPING THE PLAIN BEAM CREATING TWO CROSSES If you have ordered only a Sectional Beam proceed to the section titled Warping the Sectional Beam Various warping methods can be adapted to the AVL loom However we recommend the following method in which the warp is first wound on to the Plain Beam with the use of a Raddle Please study this method and try it We have found that it aids in getting a uniform warp ten sion especially when dealing with long warps To begin wind the warp on a warping board or reel Make sure you put in two crosses one at each end of your warp 1 The Threading Cross each thread crosses the next thread in opposite directions all are secured ina single loop RADDLE CROSS Page 4 1 V SERIES WARPING THE PLAIN BEAM SECURING THE CROSSES REMOVING THE WARP FROM THE WARPING BOARD ADJUSTING THE TENSION DEVICE Page 4 2 2 The Raddle Cross warp threads are tied in groups depending on how many ends will be put in each
30. e engages with Cloth Storage Beam Ratchet and advances the beam i Depressed Brake Pedal s releases tension on cables 3 Replace the shelf Page 2 3 BEFORE YOU BEGIN TOOLS V SERIES LOOM ASSEMBLY Let us offer a few words of encouragement You may be a little intimidated by the prospect of assembling your new loom perhaps you don t consider yourself very mechanical or are afraid you ll make some horrendous irremediable error that will finally prove to the world that you are a complete technical incompetent Relax you do many things in your daily life that are more compli cated and technically challenging than the thing you re about to do If at any point you become disoriented unsure or outright confused call us at 530 893 4915 We re here to help If you re nervous that you might be asking a dumb question console yourself with the knowledge that with absolute certainty someone else has already asked it The only dumb question of course is the one not asked Besides we know you re brilliant you bought an AVL There is a definite advantage in assembling your own loom You ll come to know it very well sooner than you otherwise would and the better you know your loom the better you ll be able to use and maintain it First you ll need tools 1 Hammer 2 Socket Wrench with 1 2 7 16 and 9 16 sockets 3 Large Bladed Screwdriver 4 Medium Phillips Screwdriver 5 Large Phillips Screwdriv
31. e flush with the bottom of both wooden Sup port Blocks 2 Take the four 5 16 x 2 hex bolts with lock wash ers and square nuts from the hardware pack Re move the square nuts 3 Insert the bolts with lock washers from the bot tom up through the top plate and support blocks Secure with the square nuts on top 4 Notice that there is a long Lever bound to 20 Release this it will hang down for the moment 5 Now look to the Cam you installed see Figure 3 5 The cable is wrapped around it and sealed down with plastic wrap Remove the wrap and unwind this Cam to Motor Cable Be sure to find the small cotter pin that is attached to the end of the cable at the copper fitting Remove it from the cable and keep it safe for the next three steps Page 3 33 V SERIES LOOM ASSEMBLY INSTALL THE CAM CYLINDER TO SLIDE PLATE CABLE INSTALL THE SPRING AND THE RETURN CORD Page 3 34 6 7 8 9 10 11 12 13 14 Wind the cable over the top of the Cam toward the outside of the loom back around under the Cam and over to the pulley mounted on top of the Motor Box Pass the cable across the front of the Motor Pulley around to the left and into a hole on the pulley s barrel The tip of the cable will now be visible in a hole on the top flat side of the pulley Pull the tip of the cable out the top of the pulley and replace the small cotter pin at the tip of the cable This will preven
32. e one Brake Pedal per Warp Beam and you ll need to depress them separately if you wish to advance from two Beams maintaining two separate tensions If you find that the Brake Cable is not releasing properly even when you ve fully depressed the pedal try releas ing a little of the nylon cord from the toggle in short increments If this is unsuccessful you may need to remove the Warp Beam Tension Cord and lightly sand the groove in the brake drum use 220 sandpaper or finer In times of high humidity especially the grain at polar sides of the drum may raise and prevent the cable from slipping Never under any circumstances should you apply wax talc or other finishes to the groove The wood here needs to be raw for the mecha nism to operate as intended If you remove the Brake Cable please be sure when you reinstall it that the looped end is secured to the J bolt that the cable is drawn immediately up from this bolt and around the back of the drum x3 and that it then routes down the front of the drum where it connects to the spring at the pedal Be sure the cable does not cross over itself at any time If the cable is installed in the wrong direction the Beam will turn easily toward the front of the loom and you will be unable to establish good tension Page 7 1 V SERIES LOOM CONTROLS CLOTH STORAGE SYSTEM REMOVABLE BREAST AND SEPARATION BEAMS SWINGING BEATER Page 7 2 The Cloth Storage Syste
33. ed to tie each group of unused heddles into a tight bundle with tie tapes or string to keep them from falling off the ends of the harness sticks or you may wish to take heddles off the loom altogether In the first six months of using a new loom with polyes ter heddles the heddles stretch out to adjust to the har nesses For this reason we do not recommend removing heddles from the loom for six months Now sley the warp ends through the reed Some weav ers start from the right side some from the left some in the middle But in all cases be sure to measure accu rately before starting so that the warp will be centered in the reed or offset four inches to the right if the warp on the beam is already offset Weavers have various ways of positioning and stabilizing the reed between the har nesses and the Breast Beam for ease during the sleying process Now that you have your warp ends ready to tie we need to prepare the apron The ends will be tied to the apron rod Notice that the apron has two hemmed ends One end has loops on it and the other end has a velcro strip The Cloth Storage Beam also has a velcro strip Measure to find the center of the Beam and using tape mark the center above the velcro strip Find the center on the apron at the end with the velcro and fold it in half with the velcro doubled on itself and facing out Match center of your fold to the center of the Beam velcro with the apron length hanging to the fl
34. eep your Harness Cables properly located during lifting of the harnesses 2 Slide the shelf into the grooves in the Harness Pul ley Supports 3 Insert the retention pin into its hole It will and should be tight It will loosen over time 4 If you cannot push the pin all the way into the shelf check that you haven t put the shelf in backwards INSTALLATION OF THE E LIFT II see Figures 3 5 and 3 11 INSTALL THE E LIFT II MOTOR BOX INSTALL THE CAM TO MOTOR CABLE V SERIES LOOM ASSEMBLY The E Lift II replicates the action of treadling When you activate the foot switch the motor turns and selected harnesses rise or fall The motion is smooth quick and precise and does not jar the harnesses You may recall that earlier you installed the Interior Cross members 19 and 20 along with the Harness Spring Support see Figure 3 11 There are some hard ware and smaller parts secured to these Cross Members It is to pieces 19 and 20 that we shall now return 1 From the packaging remove the black E Lift Mo tor Box and the hardware bag Place the Motor Box beneath parts 19 and 20 orienting it so the two electrical switches face the back of the loom the small circular plug is to the front and the four holes in the top plate of the Motor Box align with the matching holes in the wooden Support Blocks As the Motor Box is quite heavy you may wish to put something under the Motor Box to hold the top plat
35. em mounting a second spring on the eyehooks below You will have ordered your AVL A Series with either polyester or metal heddles The supporting harnesses or shafts are different for the two heddle types metal heddles whether twisted wire or flat steel are sus pended from steel heddle bars mounted in rigid frames polyester heddles are carried on Harness Sticks top and bottom In all cases the harnesses are stabilized at the bottom by a series of spring tensioned levers Spring Le vers These hold the harnesses down and prevent your heddles from floating Some weavers like metal heddles because they feel these are easier to thread others prefer the lighter and quieter polyester heddles On occasion you will find that one or more of your har nesses will misbehave That is more likely to happen with harnesses with Polyester Heddles There are a finite number of things that can cause these problems V SERIES LOOM CONTROLS TABLE 1 HARNESSES A One or more top harness stick 1 Your heddles are bunched Move a few heddles to each end collapses it assumes a diagonal together towards the cen of your harness sticks just to the angle and one leg of the harness ter of the harness or on one inside of the harness wires that con cable from which it is suspended side only This is a problem nect the top and bottom sticks That goes slack because the heddles are part of the harness structure 2 The harness cable
36. er 6 Scissors 7 Crescent Wrench 8 Level a small one will do 9 Occasional Extra Pair of Hands Packed with your hardware are a few additional tools that you may not have They ll be there when you need them Once you ve gathered your tools open all the boxes and lay the contents out just as you find them Please DO NOT REMOVE the tape from any of the components until we tell you Please too leave the hardware bags unopened until they are required Clear away all your packing materials they ll just be in the way It s best if you keep your work area as organized and free of clutter as possible Page 3 1 V SERIES LOOM ASSEMBLY ABOUT THOSE NUTS AND BOLTS Page 3 2 You ll need a space about 5 x 5 to assemble your loom In addition a conveniently located desk or table will come in very handy for several of the operations Depending on your particular style of work the entire assembly operation will take between three and eight hours NOTE Given the limited space provided by the nut ac cess holes it s a little challenging getting the nuts onto the bolt ends It gets easier with practice You ll find it helpful to push each bolt in just until it just appears in the access hole Move the nut into position over the end of the bolt and back it with your finger Push the bolt in a little further and seat the nut Slowly turn the bolt clockwise and when the nut engages tighten it most but not all the
37. er side of the Raddle Cross and secure together with string through the holes in the ends of the sticks Now remove the ties from the Raddle Cross and spread the warp out on the sticks Measure the center of your Raddle to use it as a center of your warp The warp threads should either go through the middle of the Raddle or be offset four inches to the right To feed the Raddle distribute yarns across the Raddle by dropping each Raddle Cross group into a dent in the Raddle If you are using an AVL Raddle with a sliding cover slide it on after the Raddle is threaded and secure it with two or three cord ties so it can t come off Remove the Rad dle Cross sticks when this is completed RADDLE TOP USED AS THREAD SUPPORT APRON ROD REE A Nr f an N RADDLE CROSS GROUP LEASE STICKS IN RADDLE CROSS V SERIES WARPING THE PLAIN BEAM PREPARING THE Prepare the paper for winding between the warp layers PAPER Again for the most professional results and fewer ten sion problems we suggest that the warp be as smooth tight and compact as possible This would mean not using corrugated paper or sticks as they will make the warp too soft and or lumpy Corrugated paper is just too soft and the warp can never be wound tight enough with it Heavy wrapping paper works well seventy pound craft paper is good If you are going to be using smooth slippery warp yarns like fine linens or perle cottons the edge yarns are going to need ext
38. for the E Lift II 3 37 Installation of the Compu Dobby 3 37 Figure 3 21 Solenoid Tips Aligned Correctly 3 37 WARPING THE Creating Two Crosses 4 1 PLAIN BEAM Figure Threading Cross Raddle Cross 4 1 Securing the Crosses 4 2 Removing the Warp from the Warping Board 4 2 Adjusting the Tension Device 4 2 Attaching the Raddle 4 3 Winding the Apron 4 3 Attaching the Warp to the Apron 4 3 Figure 4 3 Inserting Sticks in the Raddle Cross 4 4 Feeding the Raddle 4 4 Figure 4 4 Preparing the Paper 4 5 Figure Prepared Paper with Folding Edge 4 5 Winding the Warp 4 5 Threading Cross 4 6 Removing the Raddle 4 6 Using Two Beams 4 6 When Do You Need to Tension Your Warps Separately 4 7 Setting Two Beams 4 7 Figure Warp Routing 4 8 More Than Two Warps Only One Beam Separate Tensioning 4 8 WARPING THE Sectional Beam Calculation 5 1 SECTIONAL BEAM e Extension Cords 5 3 Feeding the Spool Rack 5 3 The Tension Box 5 4 e Tension Box Heddle Installation Instructions 5 4 Figure Tension Box 5 5 Positioning the Tension Box 5 5 e Threading the Tension Box 5 6 Winding the Warp 5 8 Figure Winding on the Warp 5 8 Adjusting the Size of the Section 5 9 Figure 5 9 Counting Turns or Yardage 5 10 Page TOC 3 V SERIES TABLE OF CONTENTS THREADING SLEYING amp TYING e ON LOOM CONTROLS e LOOM MAINTENANCE AVL CUSTOMER
39. h Warp Beam ordered These Beams are identical Each has a deep groove running the length on one side and an extension at each end to fit into the cut outs at the top of the Front 2L R and Rear 5L R Verticals Simply drop the Beams into the cut outs as shown in Figure 3 18 The slots will face down when installed and used as Sep aration Beams Figure 3 18 shows the placement of the Breast Beam when it is to be used during wind on from a Tension Box The First Separation Beam will be invert ed to expose the slot converting the Beam into a Track and Mount for your Tension Box If you have a Second Warp Beam you will need to install a bracket for the second Warp Separation Beam as fol lows NOTE If you ordered a loom with two Warp Beams these brackets and hardware will have been packed with the Side Frame Parts As noted above if you intend to use two Warp Beams in your weaving you ll need to attach a set of brackets to the Rear Verticals These Warp Separation Beam Brack ets support an additional cross member which is used to direct the warp from your lower Beam to the harnesses 1 Locate the two Separation Beam Brackets They are identical so you needn t be concerned about left and right As shown in the diagram these brackets bolt into the top of the back edge of the Rear Verticals 2 We ve pre installed the mounting bolts in the brackets Remove the square nuts from the bolt ends push the brackets into
40. he bottom two twist ties making certain that the heddles aren t twisted Now remove the twist ties 3 Count off fifty heddles and cut the loop at the top between the 50th and the 51st heddle 4 Now put the four twist ties back on the fifty hed dles that were the last to go on the harness 5 Remove these fifty and reattach the heddle retain er V SERIES WARPING THE SECTIONAL BEAM 6 Now push down on the harness that is up making the other harness come up 7 Remove the heddle retainer 8 Pull apart the top two twist ties and insert the top of the harness which is up into the space created Pull apart the bottom two twist ties and insert the bottom of the harness into the space created 9 Reattach the heddle retainer HARNESSES WITH HEDDLES STATIONARY REED PIVOTING REED ADJUSTABLE RTS Ss YH YARDAGE COUNTER REMOVABLE HEDDLE RETAINERS EYE OF HEDDLE YARN OWE TENSION PEGS POSITION OF PEGS WITH MEDIUM TENSION APPLIED TENSION BOX POSITIONING THE First bring the Front Beam to the back of the loom and TENSION BOX mount it in the two notches located on the Mid Rear Horizontals see part 6A page Next flip the Separation Beam at the back of the loom exposing the side with the groove in it If you have two Warp Beams and have mounted the Separation Bar for that beam remove it for this process Page 5 5 V SERIES WARPING THE SECTIONAL BEAM THREADING THE
41. hing the bumpers c Check that the legs are spaced equally from the outer sides of the loom Adjust as need ed with slight horizontal movements to the Beater Top This insures that the legs will not rub on the loom frame d Continue holding the Beater against the bumpers and tighten the bolts that attach the Beater Legs to the Shuttle Race and the Beater Top to the legs For ease of installation you may wish to jump to the sections in this manual for installation of the E Lift II and Compu Dobby prior to proceeding with the install of your Warp Beam s Otherwise later in this process you may find it necessary to remove these beams for easier access to the loom Once you have completed those steps return to this section and proceed from here The loom is designed to carry two Plain Warp Beams or a single Sectional Beam Plain Beams may be used in ei ther the upper or lower position A Sectional Beam may only be mounted in the upper position If you intend to use two beams simultaneously an ad ditional assembly needs to be fixed to the Rear Verticals We ll explain all that a bit later If you are using a single Plain Beam or a Sectional Beam install it in the upper position V SERIES LOOM ASSEMBLY 1 Locate your Warp Beam and the axle pockets lo cated on the front edge of the Rear Verticals 2 Loosen the little bolts that hold the flat beam retainers over the two pockets INSTALLATION OF TWO PLAIN BEAMS AND HAN
42. ion as the apron on the Plain Beam They give you reach from the Warp Beam and allow you to weave every possible inch until the end of the warp touches the last Harness you are using Make them out of a strong non stretchable linen or cotton cord You will need to make one Extension Cord for each section in your Sectional Beam For each Extension Cord 1 Measure a piece of cord long enough to reach from the axle of the Warp Beam at least one and a half revolutions around the Beam and then reach to the back most Harness 2 When measuring the length of the cords take into account that when the warp is attached to the Ex tension Cord the lark s head of the Cord and over hand knot of the warp will fall between the Cross pieces of the Sectional Beam not on them This will keep the warp smooth on the Beam without going over the knots created when attaching the warp to the cords 3 Now double that length and cut it 4 Take the two ends of the cord and knot them to gether using an overhand knot 5 All Extension Cords should be exactly the same length so it s better to cut all you will need before proceeding Next place a Spool or Cone Rack about five or six feet behind your loom Place the spools or cones for the first warp sections on the Cone Rack Make sure you put each thread through the metal eye on the spool rack so the threads do not get tangled When arranging the spools on the Spool Rack it doesn t
43. ither through the harnesses or through the back reed and you do not need to adjust tension with the Pegs Attach each baby warp to the Extension Cords and proceed as in regular Sectional Beaming proce dure Since you are not using the Tension Box for ten sion be sure to keep it taut manually Page 5 13 V SERIES WARPING THE SECTIONAL BEAM Page 5 14 9 When you come close to the end of the section take the reed cover off and continue winding the rest of the baby warp 10 Secure that section to the Beam and continue to the next one If you wish to utilize the Tension Box to maintain ten sion on your warp during the Wind On phase it will be necessary to make a Cross at both ends of your warp If you can make your warp slightly longer you can use the extra length to leave in your Tension Box for the purpose of tying on the subsequent sections V SERIES THREADING SLEYING amp TYING ON PREPARATION FOR THREADING THREADING THE HARNESSES To prepare for threading tie the threading cross sticks in a comfortable and visible position between the Back Beam and the harnesses You may also find it helpful to raise the harnesses To raise all the harnesses turn on the E Lift with the Dou ble Action off and pedal once It is not necessary to turn on the Compu Dobby at this time It is helpful to remove the Breast Beam and the Beater for further comfort and accessibility The important thing in threading is y
44. llars 8 Pivot 3 back into position so that the free end of the Axle now points to the mounting hole in 4 CAM PULLEY ASSEMBLY INSTALLED CAM CYLINDER CAM RETURN PULLEY 9 Push the Axle through the hole in 4 centering it between the two verticals Mount the last Lock Collar on the Axle to secure with both ends of the rod in their respective holes Page 3 6 INSTALL THE LOWER REAR CROSS MEMBER 17 see Figure 3 7 10 V SERIES LOOM ASSEMBLY Position the first and last Lock Collars against the face of their respective frame members and tighten them into place The other parts will be positioned and tightened later Assembly of the Side Frames is complete In the next stage of your loom assembly you ll attach the various members that connect the Left and Right Side Frames Please refer to Figure 3 7 for parts identifi cation and placement The tools you already have at hand will suffice 1 2 3 4 5 Please locate a Lower Back 17 b Cross Member Hardware Pack Sort the hardware Select four 3 1 4 hex bolts with square nuts Re move the nuts Brace both side frames on their feet about 2 apart with their access holes facing inward Put yourself at the front of the frames Pivot both frames forward 90 degrees so that they lay on their Front Verticals 2 see Figure 3 6 SET BOTH FRAMES SIDE BY SIDE ON THE FRONT VERTICALS Fig 3 6 Page 3 7 V SERIES LO
45. m consists of the Cloth Storage Beam immediately in front of your knees the Cloth Storage Apron and the Cloth Advance Handle and pawl As directed in the preceding warping instructions you ll secure the front of your warp to the Cloth Storage Beam via the apron Use the handle at the right of the Beam to advance the warp and raise the tension Sim ply release Warp Beam tension by depressing the Brake Pedal s as described above push the handle forward to engage in the toothed ratchet and rotate it down It will wrap the warp onto the beam and draw the fell away from the Beater The Pawl is that finger device that en gages in the ratchet Its job is to keep the Beam from rolling backwards and it must be engaged to hold the tension You will have either two or three of these Beams They are interchangeable and besides enhancing the structur al integrity of the loom and giving you a convenient arm rest serve to establish the warp in its horizontal plain The Beam at the front of the loom is called a Breast Beam the Beam at the rear the Back Beam or Sepa ration Beams in the event you have two Warp Beams Illustrations in the Assembly Instructions identify the mounting position of the second Separation Beam if you have one These Beams can be moved to the interior slot to help with winding on and threading The Swinging Beater is a standard feature of the V Se ries Loom You may square or rack it by loosening the four b
46. m tension on the warp Not only does this system save time but it makes it possible to wind on very long warps which would never fit on a warping board or reel First you must calculate the number of spools or cones of yarn you will need Each section is wound onto the Sectional Beam separately therefore you ll need to have one spool or cone for each end in that section if your section is 2 wide with sixteen E P I that would be thirty two spools or cones of yarn NOTE It used to be that all sections were 2 wide On an AVL Sectional Beam with metal hoops you can decide to use 1 2 or any number of inches sections You can simply add more hoops in the pre made holes or take them out To prepare for Sectional Beam warping we need to cal culate how many spools we need to wind how many yards do we need to wind on each spool total yardage for the project NUMBER OF SPOOLS Sectional Beaming requires the use of as many spools loaded with thread per individual section as your Ends Per Inch or planned sett in the reed dictates To calculate the actual number of spools required we need to know how many EPI this is the sett are you going to use in the warp what SIZE of SECTIONS 1 or 2 will you use on the Beam If your warp is set at 24 epi per 1 you will need 24 spools for a Sectional Beam with 1 sections or 48 spools for a Beam with 2 sections Page 5 1 V SERIES
47. nd more stability during this maneuver 4 5 6 7 V SERIES LOOM ASSEMBLY Place the mounting bolts from the outside in the bottom holes in the Front Verticals but not so far that they are protruding into the interior of the loom Bring the Lower Front Cross Member into posi tion with the access holes facing the bottom of the loom Push the mounting bolts all the way into the access holes and tighten with the nuts just enough to se cure the assembly For easier installation in the next step leave the loom on its Rear Verticals for now The Frame is now secure enough to support the Cloth Storage Beam in place Page 3 11 V SERIES LOOM ASSEMBLY INSTALL THE 1 BRAKE PEDAL see Figure 3 10 Page 3 12 If you will be using a single Warp Beam you ll want to mount the Brake Pedal on the left side of the loom If you have two Warp Beams you ll need to mount two pedals one left one right If this is the case note that the Left Brake Pedal is smaller than the right because of its proximity to the E Lift Spring Lever Assembly BRAKE PEDAL MOUNTING HARDWARE BRAKE PEDAL MOUNTING HARDWARE LOWER BEAM POSITION PEDAL TO RIGHT HAND SIDE UPPER BEAM POSITION Fig 3 10 a 2 3 4 5 PEDAL TO LEFT HAND SIDE BOTTOM LEFT HORIZONTAL BOTTOM RIGHT NT AL Vi HORIZON BRAKE PEDAL We NYLOCK NUT 3 8 CARRIAGE BOLT NS ca BaT Fig 3 10b Locate the Brake Pedal A
48. nt densities 4 Different structures 5 Supplementary warp techniques because some warp threads do not interlace as often as others 6 A group of special yarns for selvedges and borders Loops piles or puckers like seersucker 7 More then one layer with different setts in each layer 8 More than one layer with a different pick count in each layer SETTING TWO If you are confident in setting one beam it is just as BEAMS easy to set up a loom with two beams It might take twice as much time and you do need to be more careful not to mix sequences For those who ordered the second Plain Beam it is wound in the same manner as the first Warp Beam except your second beam will be in the bottom posi tion with the Handle at the right side of the loom This means your wind on direction will now be clockwise 1 Wind each warp on the beam the same way you would do it if there were only one beam on the loom plain or sectional Make a cross and have a pair of lease sticks with a cross in each warp 2 See enclosed picture for warp routing Page 4 7 V SERIES MORE THAN TWO WARPS ONLY ONE BEAM SEPARATE TENSIONING Page 4 8 WARPING THE PLAIN BEAM 3 Proceed with a threading as if you only had one beam one cross Follow your threading instruc tions and take special care which thread from which pair of lease sticks comes next Wene enone ROUTING alt wy gt If you have more than two warp
49. o so please orient them so that the handle on the Upper Beam is to the eft side of the loom and the handle on the Lower Beam is to the right The Dobby Head is that many cabled box hanging from the right of your loom It works in tandem with the Compu Dobby and together they provide the interface between your computer and loom The operation of the Compu Dobby is explained in its own manual and we won t reprise those instructions here Suffice it to say that it is extremely important that you achieve and maintain a good adjustment of the Solenoid Box If this device is out of tune your harnesses will behave errati cally These are the basic components on your loom You ve a world of weaving ahead you so best get started Page 7 3 V SERIES LOOM CONTROLS HARNESS SPRINGS HARNESSES Page 7 4 There are two springs of for each harness The purpose of these springs is to stabilize the harnesses and encour age their vertical fall when the shed is released Some threadings such as Summer Winter call for many more ends to be carried on one or two harnesses In this instance you may experience Harness Float An indi cation of this problem is the looseness of heddles on a particular harness above the warp ends and the ends pushing against the top of the heddle eye If you find that this is interfering with your looms ability to create a clean shed you may wish to order a few extra springs to help alleviate this probl
50. of these springs to the bottom eyehook on the right side of the harness and loop the other end over the cor relating eyehook mounted on the right side of the Spring Support immediately below the harnesses Repeat for the left hand spring This completes the installation of one Harness As sembly Now repeat steps 1 through 14 for each remaining harness Check your work periodically it s easy to connect the wrong harnesses or springs into the wrong set of eyehooks Your V Series Loom comes equipped with a Bottom Swing Beater 1 2 Locate the box containing the Beater Assembly Attached to the assembly are bags with mounting hardware In them you will find a Beater Supports 2 b Shuttle Race c Beater Top d Beater Legs 2 e Reed 1 f Reed Support 1 g Hardware Package 1 Locate the two Beater Supports and find the pre drilled holes one each on the Lower Horizontals 1 and 11 just below and forward of where the Verticals 3 and 12 meet the Lower Horizontals There is one for each side of the loom so we ll start on the right side Please refer to Figure 3 16 for correct placement Page 3 23 V SERIES LOOM ASSEMBLY Page 3 24 3 4 STANDARD BEATER SUPPORT a Orient the right hand side support so that the round spacer and metal pins are facing toward the side of the loom and the spacer with the threaded rod and the metal bracket is to the front of the loom The me
51. olts that attach it to its arms bringing it fully forward and retighten while holding it firmly in place The Swinging Beater will not take a good adjustment un less a reed is in place The angle of the race can be adjusted to one of three positions furnished by the three steel pins in the Beater Support The slots in the lower end of the Beater Legs will easily fit over these Be sure both sides are on matching pins SECTIONAL BEAM PLAIN BEAM DOBBY HEAD AND COMPU DOBBY V SERIES LOOM CONTROLS The height of the Beater can be adjusted as well by turning the three pointed Knob mounted to the bracket on the Beater Support to raise or lower the support You may wish to use a small level to ensure that you have made equal adjustments to both sides of the Beat er If you have purchased a Sectional Beam you will find it to be extremely adaptable to your needs Because each of its hoops is removable you may create sections of any width you like provided they are calculated in one inch increments Tying on to the beam is explained in the section entitled Sectional Beam Warping There are two things to remember 1 You may only use a Sectional Beam in the upper position and 2 The loom will not accommodate more than one Warp Beam if you are using a Sectional Beam The Plain Beam is provided with an apron which will allow you to maximize the length of your warp You may use two Plain Beams at a time however if you d
52. only pull until you feel what is now a uniform resistance at each group Repeat this until all of the sections are at approximately the same tension It is important to remember at this point that you are not tying to achieve weaving tension only uniform tension across the width of your warp Attaining weaving ten sion is what the Cloth Beam Ratchet is for TYING ON TO AN A new warp can be tied on to an old warp thus eliminat OLD WARP ing the threading and sleying process if the new warp introduced into the loom uses the same threading pat tern and E P I as the last warp This process is espe cially good for production weavers as it saves time It also takes less concentration and there is less chance of making mistakes in threading Page 6 4 V SERIES THREADING SLEYING amp TYING ON The tying on process starts when you are finishing the last warp on the loom Before you cut off the fabric from the old warp make sure to leave enough unwoven warp to extend one foot behind the harnesses through the heddles and about six inches past the reed when the beater is in its rear position Now open two opposite tabby sheds and insert the lease sticks into these sheds behind the harnesses Secure the sticks together with tie tapes through the holes Now carefully cut the fabric from the loom and tie bun dies of warp coming through the reed together with a half knot so the yarn can t slip back through the reed Cut the warp in ba
53. oor Press the velcro strips together firmly while pulling gently toward each side of the beam making sure it is centered V SERIES THREADING SLEYING amp TYING ON Now you can remove the tape marker and turning the top of the Beam away from you wind so the apron is wrapped once around holding itself in place Route the apron underneath the Cloth Beam and towards the har nesses Spread it out flat and center it over the Cloth Beam and insert the metal rod into the loops at the hem WARP ROUTING Now tie the ends to the metal rod Starting from the middle bring a first bundle toward you over the apron rod then around and under it Divide it in half and bring one half up on each side of the bundle Use the ends to tie a surgeon s knot It is the same as the first tie you make tying a shoelace except you loop the end through twice This kind of knot is very good for hold and read justing the tension Page 6 3 V SERIES THREADING SLEYING amp TYING ON tt th Start with one section in the middle then the far right and the far left outside ones Work your way in After tying the knot pull only until you feel some resistance and tighten the knot and proceed to the next section By now the sections that were tied first maybe quite a bit looser than the ones tied last To correct this you do not need to untie the knots simply grasp the ends and pull them away from you then re tighten the knots remembering to
54. ound the pulley and tension drum and clip the rope end to the spring V SERIES WARPING THE SECTIONAL BEAM COMBINING SECTIONAL AND PLAIN WARPING If you are winding a very fine warp say forty ends to the inch or more and do not have or do not want to wind a lot of spools or cones it may be more convenient to wind separate warp sections on a warping board or reel and go from there directly to the Sectional Beam If you decide to do this however your warp will be limited in length by what will fit on the warping board or reel If you choose this method follow these steps 1 2 3 4 5 6 7 8 Calculate number of threads for each section on your Sectional Beam On the Warping Board or Warping Wheel make baby warps for each section on your Beam Make crosses at each end raddle cross on one side and thread by thread cross on the other Take the warp off the board or reel by taking off the thread by thread cross first Put the warp threads from a first baby warp in the Raddle making sure that threads are spread evenly and that they are creating flat layers when wound on the Beam Put the raddle top on or se cure warp threads with rubber bands Instead of a regular raddle you can put a mini raddle in place of the front reed on the Tension Box In this case the Tension Box is used only for guiding threads into the sections It is not nec essary to sley threads in the Tension Box e
55. our comfort Take the time to position everything so that your body feels at ease while threading Now we re ready to thread the loom If you are right handed it is recommended to start at the right side of the warp Grasp one group of ends in your left hand and your sley hook in your right hand Direct the hook end of the sley hook through the eye of the first heddle you need to thread Pull the thread through for example if you had a straight draft on eight harnesses your first thread would go through the eye of a heddle on the 8th harness The second thread would be threaded through the eye of the first heddle on the 7th harness the third thread through the first on the 6th harness and so on Some weavers mark the center heddle on each harness and thread from center out to each side This allows for leaving an equal number of heddles at both sides of the harnesses when threading is completed Page 6 1 V SERIES THREADING SLEYING amp TYING ON UNUSED HEDDLES SLEYING THE REED TYING ON TO THE APRON Page 6 2 After threading is complete make sure that the unused heddles are all pushed to the far sides of the harness sticks between the screweyes and the ends of the har ness sticks For balance there should be approximately equal numbered groups of unused heddles on both sides of each harness In some cases such as a very wide warp with a lot of unused heddles on the ends of the harnesses you may ne
56. place and tighten the bolts against the square nuts placed in the access holes on the inside face of Horizontals 6L and O6R Page 3 29 V SERIES LOOM ASSEMBLY 1 You ve already installed your Brake Pedal s now MOUNT THE BRAKE CABLE you need to add the Cable s and Spring s SYSTEM INSTALLATION OF THE BRAKE PEDAL LEFT SIDE J BOLT UPPER BEAM J BOLT LOWER BEAM Fig 3 19 EYE BOLT 2 Brake Cables come in different lengths depending on the type of Beam you re using and its location Your Cable Assembly ies are individually bagged and marked but if you become confused consult the table below Beam Type Cable Length length is tip of loop to tip of clip 1 2 Yard Sectional 76 5 8 Upper Plain Beam 53 3 4 Lower Plain Beam 47 5 8 Page 3 30 3 4 5 6 7 V SERIES LOOM ASSEMBLY Select the poly bag with the appropriate Cable Assembly You will receive one assembly for each Warp Beam ordered It will contain a 1 Steel Brake Cable b 1 Tension Tie Up with Toggle C 1 J Bolt assembly d 1 Eye Bolt Spring Assembly Figure 3 19 indicates the holes for the cable mounting hardware Mount the J and eye bolts making sure that each points to the inside of the loom The J bolt should also point down Use a 7 16 wrench to remove the nut from the bolt in the end of the Brake Pedal then slide the bolt most of the way out Insert the
57. please to separate the top and bottom trays from the cardboard sides Pull off the cardboard top cap Lift the sides up and over the loom they are joined into a single piece Untape and remove any ancillary boxes We try always to leave a tab at the end of each piece of tape so you can pull it off rather than cut it Get a helper to aid you in lifting the loom off its plywood skids Move the loom to its permanent location Carefully untape the beater harnesses and all other mechanisms Replace any cables that have obviously been dis lodged Carefully check the loom for damage V SERIES SET UP Once you ve installed the Compu Dobby your loom will be weaving ready We ll explain the Compu Dobby in stallation later but first let s make a quick inspection You may wish to consult the section on Loom Controls if any of our part names are unfamiliar to you 1 Remove the Shelf Retention Pin at the rear of the Harness Pulley Supports Slide the shelf out and set it aside 2 Working down from the top of the loom please verify that a All Harness Cables are located in their pul b oe are attached to Harness Ca c Ae Cables are not tangled in the Dobby Head d Harness Springs are connected between Spring Levers e Treadle Cables are connected and strung over pulleys f Treadles operate freely g Swinging Beater swings smoothly without interference from adjacent parts h Cloth Advance Handl
58. prised of two parts DOBBY BACK FOR YOUR COMPU The Dobby Back This is the mechanical side of the DOBBY see Figure Dobby the flat board to which are mounted the 3 13 Dobby Cables Slide Rods and Slide Plate Page 3 18 The Compu Dobby This is the electrical side of the Dobby containing the solenoids and processor that enable the commands from your computer to fire the correct solenoids This is mounted to the Dobby Back for safe shipment in a very special box Please if at all possible retain this box in the event the Compu Dobby must be returned to AVL Looms for warranty work or servicing INSTALLATION OF THE DOBBY HEAD DOBBY BACK LOCATION OF THREE MOUNTING HOLES IN THE RIGHT SIDE CASTLE INSTALL HARNESS ASSEMBLIES AND SPRINGS 1 2 3 4 V SERIES LOOM ASSEMBLY Remove the Compu Dobby from the Dobby Back by removing the four black thumbscrews at the sides Replace the thumbscrews in their holes and store the Compu Dobby in the shipping box for the time being The Dobby Cables are now exposed Please exercise caution to avoid creating bends in these Dobby Cables Figure 3 13 shows the location of the three mount ing holes pre drilled in the right side castle Note that three mounting bolts protrude from the back of the Dobby Back If any of these have come loose you ll need to reposition them from inside the Dobby Box Note that each bolt head seats in a recess in the wood Remove
59. r Marking Thread and bring it through this Shed The two ends of the Marking Thread should now be to gether Tying them in a bowknot you have just made the Cross Continue to wind the first section on until the Cross is nearly on the Beam Cut the ends and secure to the section using a piece of masking tape Continue winding all the sections in the same manner by moving the Tension Box along its track Remove the Tension Box from its track in the Back Beam and flip the Beam over Replace the Separation Beam into its former position atop the front verticals with the groove facing down the better to now serve you as the Breast Beam When all the winding is complete remove the rubber tape unwind a few feet of warp from each section and slip one lease stick through the path created at one side of each Marking Tie Now slip another lease stick through the path created by the other side of each Mark ing Tie Secure the lease sticks together leaving about two inches between them using masking tape or string through the end holes of the lease sticks Now bring the lease sticks with the warp ends around the outside of the loom and over the Back Beam so that warp travels towards the center of the loom harnesses Now tie the lease sticks on the side of the loom so that they are at eye level when you are in your threading po sition To keep the warp from slipping forward during the threading process retighten the tension rope ar
60. r than its years Shuttles Shuttle Race Single Box Flyshuttle Picker Grooves Slide Rods sliding beater rods bobbin winder Axles pulleys spring levers overhead beater Warp Beam Metal Rods where metal works against the Paraffin wood frame Warp Beam Brake Drum LUBRICATION There are several mechanisms on your loom which will AND CLEANING benefit from the occasional light application of an ap propriate lubricant Not all lubricants are suitable in the weaving environment Machine oils and greases for ex ample may provide plenty of slick but they also capture yarn dust and will over time actually impede the action of your loom CLEANING THE Occasionally you will need to clean the air filters which E LIFT FILTERS are located on the front and back of the E Lift II housing To clean unsnap and remove the plastic baffle covers Remove the foam elements and carefully wash them in warm soapy water Be sure the filters are completely dry before you replace them CHECKING CORDS Check all cords and cables for wear All machines wear AND CABLES and cords are usually the first things that fatigue on a loom Page 8 1 V SERIES LOOM MAINTENANCE TOOL KIT AND SPARE PARTS Page 8 2 Here s a list of the basics nice to have around items 1 2 Minimum Tools as I ue Led Led ff ak a ae ae De el Ld ed bed Led Socket Wrench with 7 16 1 2 9 16 socket 6 or 8 Crescent
61. ra help in order not to slip off the sides To do this cut your paper four inches wider than the warp width and then fold over the edges an inch on each side Be sure the warp is wound be tween the two folded edges not overlapping them WIDTH 7 4 FOLD LINE PREPARED PAPER WITH FOLDED EDGE WARP WIDTH 4 WARP WIDTH C BROWN WRAPPING PAPER i WINDING THE When winding the warp on from the back i e with the WARP warp spread out in back of the loom turn the crank in a counter clockwise direction so that the warp comes in from the bottom Remember wind the warp on tightly under a lot of ten sion This will vary with each warp material but a good rule to remember is that the tension of the wound on warp must as greater as the tension during the weaving operation You will need one person to hold a warp un der tension on the back and one person to wind the warp on the beam using a handle The person winding the warp can also insert the paper For a wide heavy warp several helpers may be required Page 4 5 V SERIES WARPING THE PLAIN BEAM THREADING CROSS REMOVING THE RADDLE USING TWO BEAMS Page 4 6 If you have to do it yourself you can use the jerking method Make one turn around with your beam crank and then go to the back of the loom and jerk one nar row section 2 3 inches in width at a time to make the newly wound warp tight on the beam The idea of this me
62. remove the nuts Insert them partially as you have done previously and with the Front Cross member in place install the bolts and secure with the nuts The Rear Cross Member 20 has the same block with more hardware for the E Lift Spring Lever and a second oblong block with eye hooks in it on the top Position this piece between Verticals 4 and 16 Again point the wooden block down and all hooks and hardware to face Support 19 This will position the oblong block on top of the support Page 3 13 V SERIES LOOM ASSEMBLY 4 Select two more attachment bolts and remove the nuts Insert them partially as you have done pre viously and slip the Rear Cross Member into place Install the bolts and secure with the nuts 5 If you have not already done so take the wrapping off the Spring Support freeing it from 20 It is bolted loosely in place Remove the bolt and hardware mounted in the middle of 19 Pivot the Spring Support to bring the free end over the hole in the center top of 19 Re install the bolt bringing it in from the bottom up through 19 and the Support The nut and washer will nest in the inset opening Tighten both bolts firmly into place see Figure 11 LOCATION AND INSTALLATION OF CROSSMEMBERS AND SPRING SUPPORT Page 3 14 V SERIES LOOM ASSEMBLY 6 You re quickly becoming a Master Loom Builder have you noticed Give yourself a quick pat on the back INSTALL CENTRAL 1 Locate the
63. rota tion This is called Beam Build Up To count yards with a Yardage Counter while warping the Sectional Beam you need to place the Yardage Coun ter at the front of the Tension Box You should use an extra thread for measuring yardage because if you use one of the threads from your warp section that particu lar thread would have a different tension once you start weaving The extra thread you use for measuring pur poses can then be reused for each section V SERIES WARPING THE SECTIONAL BEAM CREATING THE CROSS FRONT PIVOTING REED ATTACHING YARDAGE COUNTER TO TENSION BOX When there is about a half yard left to be wound onto the Beam it is time to make the Threading Cross Sim ply push on the rear Heddle Frame of the Tension Box making half of the threads go up and the other half go down Now slip in an 8 piece of contrasting thread called a c through the opening called a Shed created between the threads above and the threads below Position this Marking Thread about halfway between the Tension Box and the Separation Beam AKA the Breast Beam Page 5 11 V SERIES WARPING THE SECTIONAL BEAM INSERTING STICKS IN THE THREADING CROSS READJUSTING THE TENSION Page 5 12 Now push down on the front Heddle Frame making the other half of the threads go up You may need to give a gentle tug to the section behind the Box to help the threads separate into the new Shed Now take one end of you
64. s to set and not more than two beams you need to weight tension your ad ditional warps separately do the same if you only have one beam and more than one warp to set 1 Make your warp sections on the warping board and take them off the board in a chain on a kite stick or just in a plastic bag 2 Make sure that each bundle is not too thick You will know when you need to divide each bundle if you feel that all the threads are not being ten sioned evenly 3 The weight needs to have a strong loop of string on it so the warp bundles can be slip knotted into it This makes it easy to undo the slip knot and move the weight when it climbs up to the back beam and must be let down again V SERIES WARPING THE PLAIN BEAM 4 The weight also needs to be adjustable Plastic bottles with handles filled with water are perfect You can also use fishing weights washers nuts bolts They are not as easily adjustable as water bottles but take less space The closer to the floor you can hang them the less often you need to re position them Page 4 9 V SERIES WARPING THE SECTIONAL BEAM SECTIONAL BEAM CALCULATION The AVL Sectional Beam is designed to be warped in sections with the use of a Tension Box The yarn travels directly from cones or spools which are mounted on a rack behind the loom through the Tension Box and onto the Beam Throughout the warping process the Tension Box automatically keeps a constant and unifor
65. ssembly Assemblies Remove and set aside the nut washers and car riage bolt Leave the smaller bolt assembly at the end of the pedal in place Find the Left Brake Pedal mounting hole in 16 located near the bottom of the Left Castle Vertical and immediately above the access hole Orient this assembly inside the loom at the mount ing hole in the Left Castle 16 with the long end of the pedal pointing to the front of the loom INSTALL THE E LIFT SUPPORTS 19 20 AND SPRING ANCHOR see Figure 3 7 6 7 1 2 3 V SERIES LOOM ASSEMBLY Insert this assembly through the mounting hole using light hammer taps to seat the bolt if neces sary Mount the hardware and Brake Pedal onto the bolt as follows securing tightly with the nylock Left Side Pedal Carriage Bolt Side Frame Washer Brake Pedal Washer Low Profile Nylock For the Right Side Pedal optional for second beam locate the hole at the bottom of 4 Install it to the inside of the 4 vertical inserting the carriage bolt from the outside Hardware will be mounted in this order Carriage Bolt Side Frame Washer Jamb Nut Hex Nut Washer Brake Pedal Washer Nylock Right Side Pedal The Front Cross Member 19 has two holes through the flat sides Orient this piece between Verticals 3 right side and 12 left side with the rectangular wooden block pointing down and to the inside of the loom Select two attachment bolts and
66. sup porting the shaft has come out of its pulleys at the top of the loom way your harnesses will be balanced Trace the cable back through its pulleys in the Harness Pulley Sup port and make sure that the cable is properly seated Check the action of the Dobby Cable as well Make sure that it moves easily up and down If the Dobby Cable seems to bind check for debris in the hole where it comes through the Dobby Top You may need to use a very thin piece of wire to dislodge accumulated yarn dust or other debris B The heddles float they are lifted upwards by the warp thread when you tension the warp and your shed is not even or not large enough 1 The tension in your warp is greater than the tension in the springs that hold the har nesses down Take up a link or two in the chain that spans the Harness Spring Levers for that particular harness Check the result and take up more links if you feel you need more hold down tension Do not try to make all chains the same size The size will depend on how much tension is required for each harness depending again on the number of threads go ing through that harness C One or more harnesses that 1 Left treadle isn t being Concentrate on getting both treadles are supposed to raise don t pressed all the way down all the way through their travel 2 Dobby arm out of adjust Realign the dobby arm according to ment the assembly instructions 3 Dobby cables out
67. t Vertical 5R to the inside corner of the Front Left Vertical 2L Page 3 15 V SERIES LOOM ASSEMBLY INSTALL THE HARNESS PULLEY SUPPORT ASSEMBLY 21 AND 22 see Figure 3 12 Page 3 16 2 3 4 5 2 3 These two measurements should match If they do not you will need to adjust the frame slightly by pushing and pulling at the corners until they do match The Frame will then be square Now using a level check the verticals at the cor ners and the cross pieces at bottom and top De pending on the flooring you may need to use shims under the four corner verticals in order to achieve level Once the loom is square and level then you must check and tighten all bolts and nuts that connect the frame pieces Over time due to the shaking and movement the loom experiences during use these connections will shake loose requiring periodic checking and tightening Make a check of these components a regular part of your loom maintenance Locate this assembly It is comprised of two pieces of wood Parts 21 and 22 a little wider than your loom held together by three sets of pulleys two sets of which are close to one end The entire assembly is held together by shipping wrap and tape Do not unwrap it until the unit is in place and ready to secure From your hardware pack select four 1 4 x 5 1 2 Flat Head Machine Screws and 1 4 Square Nuts Orient the Harness Pulley Support Assembly
68. t the cable from pulling out and allow for the cable to be taken up and let out from the pulley as it turns Immediately to the right of the larger Cam is the Cam Cylinder Remove the wrap and unwind the Cam to Slide Plate Cable This cable ends ina loop Manually lift the slide plate that slips up and down on the slide rods mounted to the Dobby Back If you lift it far enough it will pass over the little dobby balls Several of them will act as support for the slide plate A large hole located in the center of the bottom plate of the Dobby Back is not exposed Slip the loop up through the hole and drop it over the open tip of the large opened eye bolt on the underside of the slide plate Unpack the spring and slip one end of it onto the eyebolt at the tip of the lever Hook the other end of the spring onto the J bolt at the left side of 20 The return cord is already attached to the top right side of the slide plate with a Quick Link Undo the twist tie and straighten out the cord Check to see that the Quick Link is vertically aligned and that the cord is coming over the pulley and held in place with the retainer that pivots on the pulley bolt COMPLETING INSTALLATION OF THE E LIFT II 15 16 17 18 19 V SERIES LOOM ASSEMBLY Move to the rear of the loom and maintain some tension on the cord as you bring it down the side and under the Return Pulley and over the top of the pulley mounted on the rear E
69. tal bracket will overlap the Lower Horizontal Remove the lock nut and washer from the bolt in the rear spacer and insert the bolt through the right Lower Horizontal Slip the washer and nut back on and tighten the nut just to the point where is almost cinches the two parts together You want to leave it a little bit loose so that the Beater Support can pivot during adjustment Since the nut is a locknut it will not loosen 5 6 7 8 9 10 V SERIES LOOM ASSEMBLY Now locate two 1 1 2 long screws located in the beater hardware package Position the metal bracket that s attached to the front of the Beater Support over the two pre drilled holes and insert the screws Tighten them down Repeat this process for the left side Position the Shuttle Race at the front of the loom so that it is resting on the Horizontals 7 and 13 above the Beater Supports Orient it so that the lengthwise groove that runs along one side is to the top and facing toward the rear of the loom Now empty your hardware bag onto a table top Pick up the four 1 4 x 2 3 4 carriage bolts with washers and hex nuts Now locate the Beater Legs Notice that they have been marked to designate left and right Using each leg orient them so that with the bottom slot riding in the center pin in the Beater Support the tapered side of each leg faces away from the loom As shown in Figure 3 16 insert the bolts from the front of the race
70. th out of the nylon cord by pressing on the toggle button and moving the toggle up and down on the cord This will allow you to turn the beam backwards during winding and the Beam will be stabilized the beam when at rest Don t forget to retighten the cord when you are ready to thread the heddles V SERIES WARPING THE PLAIN BEAM ATTACHING THE RADDLE WINDING THE APRON ATTACHING THE WARP TO THE APRON Now secure the Raddle to the back of the loom If you have an AVL Raddle simply slip the mounting rods into the set of holes in the back of the rear vertical members Standing at the left side of the loom with the handle in front of you the warp will be wound on in a counter clockwise direction Put your apron on the beam with velcro and wind your beam in the counter clockwise so that your apron is wound on the beam Bring the apron around the Separation Beam and put the metal rod through the sleeve at the end You can also lash your warp sections onto that rod or you can attach another rod which has been slipped through the loop at the end of the warp with the Raddle Cross a RADDLE SEPARATION BEAM t g APRON ROD a WARP STICK N SECURE THE WARP STICK TO APRON MLLLLLILILILLILIELLLOLILILTTTTT ROD WITH EVENLY SPACED TIES aaa mins wero LT APRON Page 4 3 V SERIES WARPING THE PLAIN BEAM INSERTING STICKS IN THE RADDLE CROSS FEEDING THE RADDLE Page 4 4 Place two lease sticks in eith
71. the dents or thread the dents a little wider than two inches with twenty E P I put two ends in each dent with forty ends the reed will be sleyed 2 1 2 wide Next bring the thread straight through the Tension Peg section between the larger adjustable Tension Pegs and the smaller stationary Pegs or just above the smaller stationary Pegs if you have removed the larger ones Thread the first end through one heddle on the Front Harnesses nearest to the back plate The next end will go through the first heddle on the rear Harness Repeat this alternating harnesses for the rest of the ends The heddle system will be used later to create the Threading Cross V SERIES WARPING THE SECTIONAL BEAM Now thread the end through the front Pivoting Reed Here you have a choice of using an eight dent or ten dent reed Pick the one that can be sleyed evenly and as close to the desired section width as possible If you cannot get the exact width of the section sley your reed slightly wider This will make it just slightly wider than the space between the hoops The section will be nar rowed down by pivoting the Reed Never sley the reed narrower than the section on the Beam because it is critical that the ends wind on evenly across the width of each section If the ends are set too narrow at the Piv oting Reed there is no way to expand it After the Tension Box is completely threaded move the larger Pegs downward and tighten their wing n
72. the nuts and washers from the mounting bolts and carefully align the Dobby Back over the corresponding holes located in the right side of the loom frame as shown in Figure 3 13 You can drape the bundled harness cables up and over the top of the pulleys located directly above the Dobby Back From inside the frame slip a washer onto each bolt end then thread on a hex nut Tighten with a 1 2 socket It s time to add some of the muscle and sinew to your loom the Harness Cables Harnesses and Harness Springs If you ordered your loom with Texsolv heddles you ll need to assemble your harnesses now Please fol low the directions below If your loom is equipped with metal heddles proceed immediately to step 1 of the harness installation instructions You may wish to save space by mounting the Harness Frames as they are com pleted Page 3 19 V SERIES LOOM ASSEMBLY MAKE TEXSOLV 1 Locate the HARNESS a Harness Sticks ASSEMBLIES b Harness Wires c Texsolv Heddles d Harness Cables e Harness Springs 2 The sticks are divided into two groups top and bottom sticks The hooks on the top sticks are closer to the center The hooks in the bottom sticks then are closer to the edges 3 Select one top and one bottom stick Lay them on a table top parallel to one another about 12 apart Orient them so that the hooks point away from the opposite stick TEXSOLV HEDDLE INSTALLATION HARNESS WIRES Page 3 20
73. thod is that the warp does not need to be under ten sion all the time but the part that is on the beam has to be tight Make another turn go to the back of the loom and jerk all the sections again and so on If you have a wide warp you might need to do up to ten jerking mo tions after each turn When you come to the end of your warp insert lease sticks at either side of your Threading Cross Tie the two sticks together at each end When the warping is completed free the warp from the Raddle If you have an AVL Raddle first untie the secu rity strings lift the Raddle top off and remove the warp from the Raddle Afterwards replace the top on the Raddle and leave it in its place on the back of the loom if so desired as it will not interfere with the weaving pro cess Then be sure to bring the end of the warp around the Separation Beam so that it now travels into the loom Using a strong cord suspend the lease sticks between the Separation Beam and the Harnesses Now remove the five ties from each Threading Cross and spread the warp out on the sticks There will be times when you will want to use more than one warp which cannot be put together on one beam You will have to put them on separate beams with sepa rate tension systems V SERIES WARPING THE PLAIN BEAM WHEN DO YOU When weaving NEED TO TENSION YOUR WARPS 1 Very different size yarns SEPARATELY 2 Yarns with different stretching qualities 3 Differe
74. uts se curely to apply tension to the yarns The further down the Pegs are moved the more tension will be applied to the yarn This is an adjustable system as different yarns require more or less tension With a heavy wool the Pegs may only need to be moved half way down whereas with a fine silk the Pegs may need to be moved all the way down and the yarn wrapped an extra time around one of the stationary Pegs to get the proper ten sion Once you have adjusted the tension correctly do not change it during the winding of the Beam as long as you are using the same type of yarn Once the Tension Box has been threaded it is not always necessary to rethread it If you need to change spools or cones simply tie the new ends on to the old ends just before the rear stationary reed and pull gently on the old ends until the new ends have come all the way through the box Page 5 7 V SERIES WARPING THE SECTIONAL BEAM WINDING THE In Chapter 3 you installed the Brake Tension Device Be WARP fore winding on the warp there are a few small things to take care of on the loom First check the tension device to make sure the rope is wrapped three times around the tension drum and that the rope end is clipped to the spring which is held by the Hook Bolt Test that you are able to turn the Beam in a clockwise direction If this proves difficult you can let some length out of the nylon cord by pressing on the toggle button and moving the toggle
75. way down It s best to leave everything a little loose at first Finally if your fingers are just too big to comfortably ma nipulate the nut try backing it with a flat bladed screw driver NUT ACCESS HOLE LEFT REAR FRAME SQUARE NUTS ASSEMBLING LOWER LEFT BACK CORNER Fig 3 1 V SERIES LOOM ASSEMBLY LEFT AND RIGHT 1 Locate the Hardware Packets that came with the SIDE FRAME Frame parts and sort them to check that all parts ASSEMBLY see are present and accessible during assembly Figures 3 1 and 3 2 LEFT SIDE FRAME HARDWARE and PARTS A CHROME PLATED BOLT X 4 3 4 ASSY B CHROME PLATED BOLT X 3 1 4 ASSY C 1 4 HB X 5 1 2 ASSY 2 Front Vertical 12 Mid Vertical 5 Rear Vertical 13 Mid Front Horizontal 6A Mid Rear Horizontal 14 Top Vertical Support Fig 3 2 11 Bottom Horizontal 15 Top Horizontal 2 Now that your Right and Left Frames are assem bled you will install the Dobby Cam Pulley Assem bly This Assembly provides mechanical advantage to the right treadle greatly reducing the amount of effort required for harness lifting Please refer to Figures 2 through 5 during this Assembly Page 3 3 V SERIES LOOM ASSEMBLY 3 Locate the Right Side Frame you just assembled This side is distinguished from the Left Side by the small block mounted to 13 and two holes running through parts 3 and 4 Check that part 3 is loose enough to be pivoted on its axis RIGHT SIDE FRAME HARDWAR
76. you received the number of boxes indicated on your copy of the Bill of Lading If any are missing please call the delivery company as you may have parts still roaming the countryside Rarely is a loom damaged in shipping however if you do discover damage please call the delivery company im mediately Then call us at 530 893 4915 Freight haulers are not agents of AVL and only the con signee that is you the customer may file a damage claim It s best if you save your packing materials some freight companies wish to examine them as part of their claims process Photographs of the damaged boxes and parts are also beneficial AVL will immediately replace the damaged parts and in voice you for them You in turn should present the bill to the freight company They in turn will reimburse us they always have It s inconvenient for all of us but we ll make an extra effort to get your replacements to you quickly If you purchased your loom pre assembled please pro ceed now to the instructions Unpacking an Assembled Loom If you requested your loom knocked down move on to Assembly on page 3 1 Page 2 1 V SERIES SET UP UNPACKING AN ASSEMBLED LOOM Page 2 2 If we assembled your loom at our facility it will arrive on a pallet wholly or mostly in one unit 1 2 3 4 5 6 7 8 9 10 Cut and remove the plastic strapping Use a screwdriver or other flat implement not a knife

V-Series Dobby Loom User`s Manual

Contents

Download Pdf Manuals

Related Search

Related Contents