Home

eurodim twin tech us... - ADB Lighting Technologies

1. Lighting Technologies EURODIM TWIN TECH Parameters displayed are e Power info the type of module used by the controllers e Circuit qty Number of circuit in the module e Circuit position of the circuit taking into account the number of circuit in the previous modules Patch A B refers to the DMX patch for A and B Patch C D E refers to the patch for Artnet universe 1 2 3 Laws laws applied to this circuit Multipl Fact Multiplying factor applied to the circuit Note If a module contains less than four circuits the circuits will be displayed with empty to indicate that there is not physically present in the circuit module Selection of modules and outputs To select a module or an output position the cursor on the number of the module or the output highlighted either by touchscreen or use of the dial To view the settings of the module Touch the screen on the area of the number or use the wheel Type the number on the keypad Confirm the number by pressing on the touch sensitive area or using the dial Otherwise press 1 to scan the keypad modules or outputs in ascending order or press the 0 key on the keyboard to scan the modules or the output in descending order The field module and output are related that is to say that if you manually change the field or output module to the other will automatically update ADB www adblighting com User Manual Page 37 Lighting Technologies Issue 1 1
2. The start channel value to be taken into consideration for the increment in steps of 1 Confirm with the OK button Note the circuit s first number From dim must be lt the circuit s second number To dim during definition of the range Otherwise the range between two circuits cannot be validated The ALL key is used in order to directly enter the 128 circuits of the cabinet ADB www adblighting com User Manual Page 54 Issue 1 1 Lighting Technologies EURODIM TWIN TECH 36 ARTNET Info Menu These two screens show the status of the ARTNET connections the configuration information for the three universes managed by each controller as well as the IP addresses entered at each controller Info Artnet ARTNET CTRL 2 resent YES used YES present YES used YES UNIVERSE al cue n 0 UNIVERSE fail cue n 0 start addr 100 patch YES start addr 100 patch YES subnet Oport subnet Oport UNIVERSE 2 ai NO used UNIVERSE LR NO used black black start addr 200 patch start addr 200 patch subnet Oport subnet port resent NO used present NO used UNIVERSE 3 Pail black UNIVERSE 3 fail black start addr 300 patch start addr 300 patch NO subnet Oport subnet Oport 2 ENET ENET CTRL 11P ADDRESS 2 46 8 0 10 CTRL 11P ADDRESS 2 168 010 CTRL 2 IP ADDRESS 2 168 0 11 CTRL 2 IP ADDRESS 2 168 0 11 SUBNET 255 0 0 0 SU
3. e black the control value of each circuit fades to zero intensity black in 5 seconds e When the universe is present once more a fade is launched to the intensities given by ARTNET in a time of 5 seconds When the universe is present once more a fade is launched to the intensities given by ARTNET in a time of 5 seconds Note start addr value of the universe channel to address cabinet output 1 see ARTNET PATCH menu e X 1Sx lt 512 e not used channel value 0 or gt 512 e no circuit physically present in cabinet location 1 or circuit identification error in cabinet location 1 or operating fault Patch see ARTNET PATCH menu e Yes the addressing entered in each patch at the circuits is not in ascending order e No the addressing entered in each patch at the circuits is in ascending order e g 1 2 3 4 128 in the case where 32 modules are present in the cabinet Subnet value between 0 and 15 see ARTNET config menu Port value between 0 and 15 see ARTNET config menu When the ARTNET entries are controlled by an ISIS rotating ADB console all the subnets must have the same number Ethernet Information The IP address of each controller and the value of the sub network mask are given Important the IP addresses of each controller must be different If this is not the case it is imperative to address the ADB technical department 37 ARTNET Configuration Menu This function con
4. key on the screen to increment the output number or press keyboard key 0 or the key on the screen to decrement the output number According to the output function selected the value of corresponding patches A and B is displayed Adjust in the same manner the output control intensity value row intensity between 0 and 100 FF the output control duration delay row duration between 0 0 5 secs and 60 secs Touch the screen or use the wheel to select either the manual or automated test Manual test only the selected output will be controlled with automated variation of the intensity Automated test all outputs starting from the selected output will be tested one after the other throughout the duration and with variation of the intensity except the channels defined as undefined slot or Empty slot Press the START key to launch the manual or automated cycle Press the same START key to stop the manual or automated cycle 28 Load Save Menu This function is used to save or load the parameters of the cabinet such as patch A amp B the multiplying factor the laws and the power configuration Furthermore it is possible to choose to save the 80 1 cues upon confirmation ADB www adblighting com User Manual Page 39 Issue 1 1 Lighting Technologies EURODIM TWIN TECH Load Save Param SD 3 oe 6 EMPTY o EN CE In order to conduct a save backup or load operation the SD
5. EURODIM TWIN TECH 27 Test and Flash Menu This menu is used to test the outputs of each circuit via a command from controller 1 or 2 Test and Flash Test and Flash a 3 Gre 3 Gee 1 Oo es sade ae Value 50 iad AUTO MANUAL Mode AUTO MANUAL Delay 3 Sec Delay 3 Sec Patch Patch A 1 Patch B 12 Patch Patch 1 Patch B 12 In order to be able to control a circuit output or a set of circuits with respect to controller 1 or 2 if present verify the position of the cabinet selector in order to ensure that it matches the control by the controller selected on the screen Select the controller that is to control the output to be tested touch key CTRL 1 or CTRL 2 Note When a test or a flash is launched the DMX ARTNET are cut off 27 1 Test Tab Touch to select the test tab Used to control a circuit with constant intensity To select an output position on the output number highlighted either by touching the screen or using the wheel To edit the output number Touch the screen to select the output number or use the wheel Type the number using the keyboard Validate the output by touching the screen to select the zone in question or using the wheel Otherwise press keyboard key 1 or the key on the screen to increment the output number or press keyboard key 0 or the key on the screen to decrement the output number According to the outp
6. Non dim see information in Status because in this case this type of module does not enable dimming ADB www adblighting com User Manual Page 46 Issue 1 1 Lighting Technologies EURODIM TWIN TECH 32 2 Range Key Used to select a set of circuits to be scanned included within a range Important note the FLUO Non Dim and sinewave modules and those circuits that apply the switch law will not be selected Enter The start dimmer number From dim The end dimmer number To dim Confirm with the OK button Note the circuit s first number From dim must be lt the circuit s second number To dim during definition of the range Otherwise the range between two circuits cannot be validated The ALL key is used in order to directly select the 128 circuits of the cabinet r Scan the loads V RANGE Circuit selection All From dim To dim 50 3 Gre Crew emoe ree Status 32 3 Scanning the Outputs Launch the scan by pressing the SCAN key Confirm your choice Several stages are conducted during the scan of a circuits output and which can be viewed on the status row Test at 14 of 230V in order to detect the presence of a short circuit Stopping of the procedure in the event of a short circuit Dimming of the output up to 50 Measurement of the neutral current at 50 ADB www adblighting com User Manual Page 47 Issue 1 1 Lighting Technolog
7. A DMX B and ARTNET inputs three available universes and cue played and allocated to a circuit that is taken into account in order to give the output dimming level ADB www adblighting com User Manual Page 9 Issue 1 1 Lighting Technologies EURODIM TWIN TECH When the selector is set to A R the circuits of each module are controlled according to the following rule the highest value amongst the DMX A DMX B and ARTNET inputs of the two controllers is taken into account when controlling this circuit Example Control using DMX A and DMX B inputs Controller 1 Controller 2 DMX A circuit 1 100 circuit 2 0 Circuit 1 100 circuit 1 90 Circuit 2 100 DMX B circuit 2 100 Notes The PCB3031 board also enables the DMX A inputs to be connected between controllers SW1 selectors 5 and 6 set to ON the DMX B inputs to be connected between controllers SW1 selectors 7 and 8 set to ON CPU 2 DMX A k i Ci CPU 2 DMx B kut LIN THROUGH J LIN THROUGH PCB 3031 board ADB Lighting Technologies www adblighting com User Manual Page 10 Issue 1 1 EURODIM TWIN TECH 9 Cabinet Ventilation The cabinet is ventilated by three fans arranged at the top of the cabinet which extract hot air from the cabinet These fans can operate at two different extraction speeds 1 and 2 The fans start on speed 1 normal air extraction if one of the circuits is controlled at above 50 intensity Belo
8. Cues Menu Capture Instead of entering the cues using the Editing function this function is used to capture the highest intensity of the sources present at the controller s input DMX amp ARTNET this being the case for each circuit and to save it in a cue from 0 to 80 Capture DMX Z ARTNET 3 Be ww E Selecting a cue To select a cue go to the cue number highlighted either by touching the screen or using the wheel To edit the cue number Touch the screen or use the wheel to select the zone of the number in question Type the number using the keyboard Validate the cue by touching the screen to select the zone in question or using the wheel Otherwise press keyboard key 1 to scan the cues in ascending order or press keyboard key 0 to scan the cues in descending order Important when a cue is edited there is a loading time The status row at the bottom of the page informs the user of this status Wait for the synchronisation to be complete in order to obtain a correct reading of the intensities of each of the cue s circuits 20 1 DMX ARTNET Capture Press the CAPTURE key to launch the memorisation operation The values appear in the table after a few seconds The cue number is followed by an asterisk to indicate that the captured DMX ARTNET values are displayed Press the SAVE key to save the intensities in the cue displayed The cue becomes existing E ADB www adblighting com User
9. DMX is completed DMX gt CUE gt DMX Intensity CMD PLAY CUE CMD STOP CUE A Time DMX Fading CUE Fading 5s DMX gt CUE 1 gt CUE 2 gt DMX Intensity CMD PLAY CUE 1 CMD PLAY CUE 2 CMD STOP CUE p H Time DMX Fading CUE 1 Fading CUE 2 Fading DMX z Cue 1 Cue 2 5s ADB www adblighting com User Manual Page 31 Lighting Technologies Iss ue 1 1 EURODIM TWIN TECH 22 Cues Menu Copy This function is used to copy an existing cue to any other cue existing or not Ge Copy cues Te 3 Gee Cuen copy gt cuen 1 Ef copy CENTS Existing source cue destination cue indication Selecting the original cue The field memory source can only display existing memories Note Cue 0 always exists To select a cue position on the cue number highlighted either by touching the screen or using the wheel To edit the cue number Touch the screen or use the wheel to select the zone of the number in question Type the number using the keyboard Validate the cue by touching the screen to select the zone in question or using the wheel Otherwise press keyboard key 1 to scan the cues in ascending order or press keyboard key 0 to scan the cues in descending order Selecting the destination cue Each of the cues may be overwritten To select a cue position on the cue number highlighted either by touching the scr
10. Manual Page 29 Issue 1 1 Lighting Technologies EURODIM TWIN TECH 21 Cues Menu Play This function is used to play an existing cue The fade time corresponds to the rise time defined in the Cue Edit menu Play cue o Fade time Cun 0 E des PLAY Selecting a cue Only the existing cues will be displayed E To select a cue position on the cue number highlighted either by touching the screen or using the wheel To edit the cue number Touch the screen or use the wheel to select the zone of the number in question Type the number using the keyboard Validate the cue by touching the screen to select the zone in question or using the wheel Otherwise press keyboard key 1 to scan the cues in ascending order or press keyboard key 0 to scan the cues in descending order Play a cue Press the Play key to launch the cue The information in this status lets you know the progress of memory fade Fade to cue x progressive rise to the nominal control intensity of each circuit Cue played x the fade is completed the memory is played with current output values ADB www adblighting com User Manual Page 30 Issue 1 1 Lighting Technologies EURODIM TWIN TECH Press the Stop key to interrupt the play The DMX ARTNET will entirely regain control in five seconds with a fade Note It is not possible to replay a cue immediately after a stop it is necessary to wait until the fade to
11. Technologies EURODIM TWIN TECH CPU Switch EEL I iv Iy EEE LE F SS aa aaa a a aa 8 1 Synchronization The human interface is synchronized continuously between two controllers if present If two controllers are present data from a controller the one inserted into the slot from the top with the exception of the page Diagnosis of the cabinet or information from the selected controller using the tabs CTRL1 and CTRL2 If the controller 1 is a not functional timing continues with the controller 2 If the cabinet has only one controller all the information obtained from this controller Note Only the controller in slot from the top is able to detect modules in the cabinet see Chapter Power Configuration and to report the status of sinewave and thyristor modules with full diagnostic option see section Module Measuring and Diagnostic Modules If one controller is functional and inserted into the slot at the bottom the cabinet will work but the human interface will not be able to present the modules or diagnostic information modules 8 2 Module Control The selector allows the Controller unit in service to be chosen It may be set to position 1 A R or 2 When a controller is selected 1 or 2 the DMX A DMX B and ARTNET signals present at this controller s input are used The software configuration is HTP Highest Take Precedence by default It is the highest value of the DMX
12. an immediate effect on the light dimming In the Multiplying Factor column we attribute a multiplying factor between 0 and 100 to the circuit Ultimately the circuit control value is as follows DMX channel value gt law applied to the circuit gt multiplying factor ADB www adblighting com User Manual Page 20 Issue 1 1 Lighting Technologies EURODIM TWIN TECH Example of a circuits output voltage DMX channel value 50 120 Vlaw Mult fact 50 Use the wheel in order to rapidly move to the row of a circuit The row selected is highlighted To attribute a law position on a row Touch the zone where the current law is displayed making the table of available laws appear Touch to select the law from the table the law selected is highlighted For the user laws first select the number between 1 and 6 using the and keys Touch the highlighted zone to validate and attribute to the circuit To attribute a multiplying factor position on a row Touch the zone where the multiplying factor is displayed in order to edit the value Enter the value using the numeric keyboard between 0 and 100 Touch the zone where the new value is displayed in order to validate Important after validation this action has an immediate effect on the light dimming Note If the value attributed is 100 the screen displays FF Any value entered that is beyond 100 is limited to 100 FF If the law att
13. copied Patch DMX amp ARTNET Laws Cues Modules used Cue priority ARTNET configuration Load measurements Action in the event of a absent source fg Synchronisation 3 Copy from CTRL 1 gt CTRL 2 SYNC Copy from CTRL 2 gt CTRL 1 SYNC Status re Touch one of the SYNC keys to launch the copy procedure between controllers that is from controller 1 to controller 2 or vice versa A window opens and a confirmation request is requested During the copy operation the Status row indicates the state of progress by displaying the percentage copied When the copy operation is completed the following information is displayed Synchronisation completed 39 Managing the Alarms The cabinet diagnostic page indicates any malfunctions of the cabinet with a warning message Example Choose the modules to be used An exclamation mark also appears Touch the exclamation mark to display a screen page grouping together the errors list ADB www adblighting com User Manual Page 58 Issue 1 1 Lighting Technologies EURODIM TWIN TECH es Diagnosis of the cabinet 3 Gre CTRL INFO ctrl board active YES frequency 50 hz hardware communication OK software version 5 060 temperature OK EURODIM TT INFO Ref modules are used for dimming phaser OK fan 1 OK phases OK fan 2 OK phaset OK fan 3 OK HMI V 5 060 Warning message DMX INFO dmx a start addr 1 patch a NO dmx b star
14. filled in Validate the said field Increment or decrement a value Validate or cancel a function Display one of the different available menus Return to the main screen or the list of menus The key or zone selected is highlighted There is no recording confirmation when the screen page is changed When a field is edited and its value is modified it is possible to cancel its recording before validation by pressing another touch zone on the screen 3 2 Numeric Keyboard The numeric keyboard enables the user to Add a field s value when the field is edited Increment a field s value by pressing key 1 or decrement by pressing key 0 Directly access a screen page next page using key 1 previous page using key 0 Enter the access code in order to access the different user levels Note Any value entered that is beyond the user range is limited to the maximum value 3 3 Navigation Wheel The wheel may be handled by rotating clockwise or anti clockwise in order to Select a field from a menu or choose a menu from the two menu screen pages Cancel the validation of a field when the latter is edited ADB www adblighting com User Manual Page 5 Issue 1 1 Lighting Technologies EURODIM TWIN TECH Pressing the navigation wheel enables the user to Edit a field to be filled in Validate the highlighted field Validate or cancel a function Select a menu or function 4 Accessing
15. 4 128 where 32 modules of four circuits are present in the cabinet The maximum ambient temperatures are defined in EURODIM Twin Tech data sheet ADB www adblighting com User Manual Page 15 Issue 1 1 Lighting Technologies EURODIM TWIN TECH DMX ASB fail action implemented in the absence of an DMX A B signal see Priority DMX fail menu three actions are possible last value the last values received to control the circuits are used on a permanent basis as long as the DMX signal is missing e cue 0 the DMX signal channel values are replaced by the content of cue 0 with a fade time of cue 0 and will be played as long as the DMX signal is missing black the control value of each circuit fades to black in five seconds When the DMX signal is present again we return to the DMX values with a five second fade 13 Presentation of the ARTNET Information Page Info Artnet ac 3 Gee ARTNET CTRL 2 present YES used YES UNIVERSE 1 fail cue n 0 start addr 100 patch YES subnet port present NO used UNIVERSE 2 fail black start addr 200 patch subnet port present NO used UNIVERSE 3 fail black start addr 300 patch NO subnet port 2 ENET CTRL 1 IP ADDRESS 2 168 0 10 CTRL 2 IP ADDRESS 2 168 0 11 SUBNET 255 0 0 0 Explanation of the fields see chapter ARTNET INFO ADB www adblighting com User Manual Page 16
16. BNET 255 0 0 0 This page is divided into two zones A zone CTRL1 or CRTL2 key providing information on the status of the universes and their configurations for each controller Azone ENET providing the IP addresses entered for each controller Note Only the ARTNET present missing information depends on the controller In effect each controller has its own ARTNET input The back button called MENU or DIAG is used to return to the previous screen 36 1 ARTNET Information For each of the three universes 1 2 3 the following information is available Present e Yes detection of the Ethernet frame corresponding to the universe e No no reception of the Ethernet frame corresponding to the universe Used see ARTNET Configuration menu e yes the universe values are taken into consideration for the control of the circuits e no the universe values are not taken into consideration for the control of the circuits Fail action implemented in the absence of the universe see Priority DMX fail menu three actions are possible ADB www adblighting com User Manual Page 55 Issue 1 1 Lighting Technologies EURODIM TWIN TECH e last value the last values received to control the circuits are used permanently as long as the universe is missing e cue 0 the values of the universe channels are replaced by the content of cue 0 and will be played as long as the universe is missing
17. DB www adblighting com User Manual Page 45 Lighting Technologies Issue 1 1 EURODIM TWIN TECH 32 Loads Scanning Menu Scan Important this function is only accessible if the sequential diagnostic kit has been installed in the cabinet In effect it is used to measure the neutral current on the module power line busbar This function is used to launch a test verify the loads present at the output of each circuit using a current measurement in relation to the loads provided by the Load verification Learn menu Er Scan the loads 3 Gre fy Wt 1 Notoad Notoad ere QE Wola odo selection V s Wold Nolo CA fout Noted on flou fout 22 6 fleuri found enrio oto C2 fout ood Status Crew ne Car 32 1 Selecting the outputs to be scanned There are several ways to manually select the outputs that we wish to scan By touching the module dimmer number By selecting the row using the wheel by pressing down By positioning on the row using the wheel and by pressing key 1 to select press key 0 to deselect A validation symbol appears in front of the module dimmer number Important note It is not possible to select a sinewave or FLUO module circuit for the scan see status A circuit cannot be selected if the switch law is applied see information in Status because in this case this circuit s load is not dimmable A circuit cannot be selected if it is defined as
18. EURODIM Twin Tech User Manual V 1 1 Bene Bae oii j be bi h b b he be bs b b be le b b i Be 7 ADB Lighting Technologies M 3213 1106 53 213 EURODIM TWIN TECH Table of content Ms ola oTa o A E ce tec ewe tub ced eats ames the eee cewecebce eee tus une ae teckl de AE 3 2 Description of the Unit asisiccccccccacicccctesccepssccsecanceeccesctstecessaendcsnccncncee anainn daenda aiana asaina iaai 4 3 Using the TTD HUMAN INTERFACE HM eeeceeeeeeeeeeeeeeeeeeeeeeeesneeeneneeeeeeeeeeseeseenneees 5 3 1 Fe RARE A ea sees ea eects E E ee 5 3 2 N meric MSY DO ANG ER ting adie renetmeatucerdheredaeradedsrdhesesersneteneues 5 3 3 Navigation Wheel sise 5 4 Accessing the TTD HUMAN INTERFACE HM ccccccssseeeeeeeeeeeeeeeeeeeeeneeeeeeeeeeseeeeeeenenes 6 E EA E E E een nn nn tisse 7 6 Online Assist NC s v sisovensiononsn no noneneke nn de anse er ass EA EENEN AKEN N ENPE EKAN ENKAN Eain 7 7 Menu Tree SIUC UG sce oasasececesccaciencesaceeetscctesccssacnensscatenncssachansecctsanceaacseusscatasnsacseaseacssensenacs 7 8 Cabinet Configuration ss isnriemesansisnniincenseesctonsss 8 8 1 Synchronization Eee ee eee ee neem eer eee eae ee eee 9 8 2 Mod le CONGO ee em ne etes 9 9 Cabinet VERE ATION 5 sn nenn nn nssn sas tenons tass Rae nes nine not snsnnennas nn nnsResn ennnen 11 10 Initial User Configuration 0 ssssansssnsineensssnsonseinsiuns 11 10 1 Description of
19. IM TWIN TECH module identification table In the Reference column we are given the type of module that will actually be used by the controller to control the circuits This reference may be modified manually If a position in the cabinet is not used the user must fill it in as an undefined slot Use the wheel to view the ID of each module 17 1 COMPARE Key This function is used to compare the ID given in the PRESENT column and the ID given in the REFERENCE column for each module This is used to check that the content of the references is up to date with respect to the modules actually installed ADB www adblighting com User Manual Page 23 Lighting Technologies Issue 1 1 EURODIM TWIN TECH When the key is selected two messages can be displayed Ref and present modules are identical In this case there is no module identification problem Ref and present modules are different The message also displays the number of different modules When the OK button is touched the screen automatically displays the first module where the ID is different In this case it is necessary to verify the identification of the module physically present in the cabinet and if necessary modify the ID in the REFERENCE column 17 2 REF PRES Key This function is used to copy the content of the IDs of the PRESENT column to the REFERENCE column for all the modules Attributing an ID To attribute an ID to a module in the REFERENCE col
20. Issue 1 1 Lighting Technologies EURODIM TWIN TECH 14 Description of the Menus PATCH LAWS MULT F CONF POWER SCAN LOADS MOD MEAS MOD DIAG CUES OMX FAIL VIEWALL TEST FLASH ARTNETPATCH VIEWARTNET ARTNET SET a P LOAD SAVYE SETTINGS NEXT SERVICE SYNCHRO PREVIOUS Two screen pages are available in order to choose a function enabling the cabinet to be configured using one of the following menus Patch to edit patch A or B for each circuit Laws Mult F to choose the law used and the multiplying factor for each of the circuits Conf Power to assign the modules used and detected in the 32 cabinet locations Cues DMX fail cue management and action to be performed after a absence of DMX ARTNET View all overall view of all the parameters per module or per circuit Test Flash to launch a test or the flash of a circuit Load Save to save and load the parameters of the controllers and of each circuit Settings Human Machine interface configuration Scan loads to measure scan the loads connected at the outputs of each circuit Mod Meas gives the voltage and current measurements for each circuit Mod Diag gives the diagnosis of the outputs of each module ARTNET patch to edit the patch of the three ARTNET universes for each circuit View ARTNET general information on the ARTNET universes and the Ethernet connection ARTNET set to configure the three ARTNET universes ADB Service function available to ADB tech
21. NERE EE EE A E NEER 27 19 2 Tim Exist KOy esscicanceivcassdeicasnsasavaatsdercsansdesicasidsrcanniaervaatsdercsansderixatidsreasniaerveatiderxeasies 28 20 Cues Menu Capture epics aces pieces cette cee ec eee ee 29 20 1 DMX ARTNET Capture cscs cos Sackett aces dawiegetincigdeaie dese ciated sin 29 21 Cues Menu Play scceccccacecssetecses ceracesecasscesccesacaveceracctecececessseseratent ace ctissereeneteeeenmencie 30 ADB www adblighting com User Manual Page 1 Issue 1 1 Lighting Technologies EURODIM TWIN TECH 22 QUES MENU COPY Po ee ni 32 23 Cues Menu Erase 0 Eiaa idan eu iaai E anidan 33 24 Cues Menu Priority DMX AI tien tie ee 34 24 1 PRO eie eao aa aa 34 24 2 DMX ARTNET AIS nice 34 25 Cues Menu Play Chaser nds ssenisssncisnnisesrminsssepsisnsrsesmast ele 35 20 OVervieW ice cen ae wee ene ee eee 36 27 Test and Flash M dine nn entendent Saanaa aaia aan tan 38 27 1 D S A ER deine E E EA EREE EEEE E RS 38 27 2 ASTRA r a ee 39 28 Load Save MENU Ne nes cece whence ad ecient a Anaea entit s nada 39 28 1 Saving the DArANICI TS NA nu NN nes den 40 28 2 Loading the parameters sionisme tentent ENEE ERE 41 29 Settings MIU keksien iaraa aes ci eats ten Secret nee 41 30 Load Scanning Menu 42 31 Load Scanning Menu Learn 2822205 sssrsstisen nn sssmnsti cents nn cotes gttenns tes 42 31 1 Manually selecting the loads 0 ccceeeeccsccceeeeeeeeeenenaeeeeeeee
22. card must be present in the slot planned in the TTD HUMAN INTERFACE HMI Unit located behind the right contractors door If no card is detected the status row displays No card detected The List key is used to reread the content of the backup files present on the SD card There are ten locations available on the card in order to conduct backups Each file saved is recorded in the following form EDTT 01 02 03 gives the file name V3 backup version With cue or without cue with backup or without backup of the cues in the file 18 02 11 date of manual recording of the backup 28 1 Saving the parameters Select one of the ten locations in which to save either by touching the screen or using the wheel We can position on an existent file In this case the file is overwritten during the save without a confirmation request Touch the SAVE key to launch the save A first window requests the save date to be manually recorded After validation a second window requests confirmation of the save cue execution yes no Next a third window requests the user s confirmation of the save operation configured as described The status row enables the user to monitor the state of progress of the save operation ADB www adblighting com User Manual Page 40 Issue 1 1 Lighting Technologies EURODIM TWIN TECH 28 2 Loading the parameters Select one of the save files either by touching the screen or using the whe
23. creen enabling access to all menus 2 Anumeric keyboard 3 Anavigation validation pushbutton wheel When the right hand side door of the cabinet is opened the rear of the Unit gives access to the following 1 An opening on the rear face to activate the software reset button in the event that the touch screen becomes blocked 2 Anopening in the side face for insertion of the SD memory card 3 Aconnector to link up to the Twin Tech cabinet Controller units 4 Acontrast potentiometer and a brightness potentiometer for the LCD touch screen ADB www adblighting com User Manual Page 4 Lighting Technologies Issue 1 1 EURODIM TWIN TECH An original memory card is provided with the Unit The Unit and its interface are not operational as long as the card is not inserted into its slot The SD memory card can be changed by another SD memory card if the conditions are respected 1 The maximum size is 2GB 2 You can copy the following files from de origin card to new card e EDTT1 e EDTT2 e TRANSLAT if it is present on the origin card e Help 3 Using the TTD HUMAN INTERFACE HMl 3 1 LCD Display When the cabinet is activated an initial home page appears on the LCD display allowing access to the Cabinet diagnostic screen page which is considered as the main screen Manually pressing the touch zones on the main screen or the screens of the different menus generally enables the user to Edita field to be
24. d see manual load selection Confirm with the OK button Note the circuit s first number From dim must be lt the circuit s second number To dim during definition of the range Otherwise the range between two circuits cannot be validated The ALL key is used in order to directly enter the 128 circuits of the cabinet 31 3 Automatically selecting the loads Press the AUTOMATIC key three options are available Measurement the load information available in the Measurement column of all the circuits is recopied to the EDIT column After copying the name of the left hand column changes and becomes SCANNED Present the information originating from the PRESENT column see Power Configuration menu are recopied into the EDIT column After copying the name of the left hand column changes and becomes PRESENT Reference the information originating from the REFERENCE column see Power Configuration menu are recopied into the EDIT column After copying the name of the left hand column changes and becomes REFERENCE Select one of the options either by touching the screen or using the wheel and confirm the choice Note for the options PRESENT and REFERENCE the column is updated automatically based on what was defined in conf puiss ee Learn loads 3 Gre fa als ee d2 2 se su SRE RENE 2 o r w e TE Ge ef wv W D E a Automatic selection Reference A
25. d and if the overload is severe again a second test is conducted If the overload is still severe a status message is displayed at the bottom of the screen requesting the user to set all the DMX ARTNET inputs of the circuit to zero for 30 secs Thyristor with diag 1 Displays N A if the breaker has blown 2 Displays YES if the breaker is OK and e If the load is gt 3 5KW for a 3kW module e if the load gt 5 5 5KW for a 5kW module e if the load is gt 11KW for a 10KW module 3 Displays NO in all other cases ADB Lighting Technologies www adblighting com User Manual Page 51 Issue 1 1 EURODIM TWIN TECH OverCurrent per circuit Sinewave e Displays low if the current is gt 13 A e Displays average if the current is gt 16 A e Displays Severe if the current is gt 20 A Thyristor with diag always N A Short circuit per circuit Sinewave Displays NO Displays YES e The control is automatically set to zero e After 2 mins an actual control test is repeated and if the overload is severe again a second test is conducted If the overload is still severe a status message is displayed at the bottom of the screen requesting the user to set all the DMX ARTNET inputs of the circuit to zero for 30 secs Thyristor with diag always N A Temperature Sinewave 1 Displays OK 2 Displays too high gt automatic control reduction until the tempe
26. e output on the cabinet from 1 to 128 The channel attributed for each universe is given in the right hand column Start by selecting universe 1 2 or 3 Use the wheel to rapidly move between all the rows of the patch The row selected is highlighted To attribute a channel position on a row and use The touch screen and the numeric keyboard to enter a value Press key 1 directly to increment the value by 1 between 1 and 512 in relation to the first value available on a previous row Press key 0 directly to decrement the value by 1 between 1 and 512 in relation to the first value available on a previous row The Range key in order to enter values between two circuit references ADB www adblighting com User Manual Page 53 Issue 1 1 Lighting Technologies EURODIM TWIN TECH Important Specific case for row 1 1 If key 0 or 1 is used the value taken into consideration corresponds to the content of output 128 if available otherwise to output 127 and so on If the value entered is 0 or greater than 512 the circuit cannot be coordinated and the message Not used is displayed 35 1 Range Key Used to attribute an ascending patch value in graduations of 1 to a set of circuits included within a range Patch Artnet RANGE All From dim To dim 32 Artnet 100 3 Gre rew rance re Enter The start dimmer number From dim The end dimmer number To dim
27. eeeeaaaaaaaeeeeeeeeeeessnaeaaeeeeees 43 31 2 Range RE ee ee et ee ee oe ee 44 31 3 Automatically selecting the loads eteceenaaeeeeeeeeeeneea 45 32 Loads Scanning Menu Scan 2 80 na Une er ne resssere tee spessese 46 32 1 Selecting the outputs to be scanned ss 46 32 2 MN SR ee a ae a a EEEE 47 32 3 Scanning the Outputs nn ee mn lion 47 33 Module Measurements Menu eccccceeeseseseneeeeeeeeeeeeeseeeeeeeaeeeeeeeseesneneeeeeeeeesseeeeeeneees 48 33 1 Selecting the modules and circuits sccitkincdsenitinnmdineininnitbmuiibinminnsiei 49 34 Modules Diagnosis Menu nnmnnn nenna 49 34 1 Selecting the modules and circuits sin nesiiinets eee aes 50 35 ARTNET Patch GI ssscccecassccsscerscestccsacesscetssczexeracanene cece sacesacatenctaceceuseaceseeseicceermustomsaecints 53 35 1 Ra ang Key rerien ee ee 54 30 ARINET Info MON cen ei cee 55 36 1 AR ONE T JITONTIARGN PE ER E E EERE 55 37 ARTNET Configuration Menu ecccccccessseeeeeeeeeeeeeeeeneseeeneeeeeeeeeeenseeeeneeeeeeeeeeesesennnees 56 37 1 Selecting Universe Mode ee 57 37 2 Subnet and Universe POS Sn der du di du nn 57 38 Synchronisation Menu ssssssnenssennunnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnn nnmnnn nnana 57 39 Managing the PALES ics sot 2 seemed 58 39 1 Errors List Screen Pages ss nati wanna i aa R aE i ERARA 59 39 2 List of Errors d
28. een or using the wheel To edit the cue number Touch the screen or use the wheel to select the zone of the number in question Type the number using the keyboard Validate the cue by touching the screen to select the zone in question or using the wheel ADB www adblighting com User Manual Page 32 Issue 1 1 Lighting Technologies EURODIM TWIN TECH Otherwise press keyboard key 1 to scan the cues in ascending order or press keyboard key 0 to scan the cues in descending order Copy Press the COPY button and confirm in order to perform the cue copying operation 23 Cues Menu Erase This function is used to delete the existing cues only Erase cue a Cuen 1 1 1 1 FF 1 2 2107 1 3 3 07 14 4 07 21 5 FF 2 2 6 FF 2 3 7 0z 2 4 8107 Selecting a cue Only the existing cues will be displayed Note Cue 0 always exists To select a cue go to the cue number highlighted either by touching the screen or using the wheel To edit the cue number Touch the screen or use the wheel to select the zone of the number in question Type the number using the keyboard Validate the cue by touching the screen to select the zone in question or using the wheel Otherwise press keyboard key 1 to scan the cues in ascending order or press keyboard key 0 to scan the cues in descending order Erase Press the ERASE button and confirm to validate the deletion The cue th
29. el Touch the LOAD key to launch the load operation A window is displayed asking the user to confirm the loading of the cues yes no if they have been recorded in the file The status row enables the user to monitor the state of progress of the load operation The operation to load the parameters to the controller is completed when the status indicates Synchronisation completed do not leave the function before the message appears 29 Settings Menu This function is used to activate the buzzer select the TTD HUMAN INTERFACE HMI display language activate the screensaver and indicate a database change 3 Settings Buzzer Language Screen Saver lt Time 60 sec Touch to select the settings Buzzer When it is activated ON the buzzer emits the signal when there has been an action on the wheel the numeric touchpad or the touch screen Language French English Screensaver If the screensaver is active ON the TTD HUMAN INTERFACE HMI returns to the home page if there has not been any action by the user and resets the user level to zero A level four user access code is required in order to deactivate the screensaver Changing the database When a PC is connected to the cabinet with TT manager and the latter makes a modification to a parameter the user may be alerted but without the possibility of intervening e ON selected in this case the TTD HUMAN INTERFACE HMI displays the d
30. en takes the following values by default ADB www adblighting com User Manual Page 33 Lighting Technologies Issue 1 1 EURODIM TWIN TECH Intensity 0 Fade time 0 min 5 sec Wait time 0 min 5 sec Cue exists No Note Cue 0 may be deleted i e filled in with the default parameters but it will continue to exist Intensity 0 Fade time 0 min 5 sec Wait time 0 min 5 sec Cue exists YES 24 Cues Menu Priority DMX fail This function is used to prioritise the selection amongst the DMX ARTNET inputs and cue played and also to replace a missing source Priority DMX fail Q BS 3 Gre Priority between the cues and the dmx and Artnet inputs OMX MASKED The DMX ARTNET On Artnet fail after 10 sec values arene i cr ro ith Cou er 24 1 Priority When memory is performed using the play memory the DMX ARTNET can be hidden by selecting DMX MASK or if the highest value between memory and DMX ARTNET shall be taken select HTP 24 2 DMX ARTNET fail In case of DMX or ARTNET signals is not present or failure the latest values are kept for 10 seconds After that the source is replaced by one of three options The last control value received from the source that has disappeared Control by cue 0 with fade rise time of cue 0 0 control black with fade in five seconds Priority to the highest value present ADB www adbligh
31. er circuit Sinewave always N A Thyristor with Diag 1 Displays OK if everything is fine 2 Displays Damaged if a voltage gt 210 V is measured whereas the control measured by the module is lt 25 Breaker per circuit Sinewave 1 Displays N A if the control value is lt 17 or the circuit is overloaded or short circuited 2 Displays OK if the control value is gt 17 and not overloaded or short circuited 3 Displays triggered if the control value is control gt 17 and no output voltage is measured on the circuit Thyristor per circuit 1 Displays OK if the breaker is engaged 2 Displays disengaged if the breaker has blown Load per circuit Sinewave amp Thyristor with diag 1 Displays N A e The control is set to zero e and or the output voltage is too low 2 Displays NO e If the control value is gt 0 e The output voltage is measured e and the current is not measured 3 Displays YES e If the control is present e And the output voltage and the output current is measured Overloads per circuit Sinewave 1 Displays light if the voltage is gt 13 A for 30 secs 2 Displays medium if the current is gt 16 A for 10 secs e Here the control decreases every 500 ms until the current reaches lt 13 A 3 Displays Severe if the current is gt 20 A for 1 sec e The control is automatically set to zero e After 2 mins an actual control test is repeate
32. ference modules are used for dimming indicates that all the modules installed in the cabinet are identified by the software and enable the cabinet to operate normally An error message may be displayed instead In this case press the exclamation mark to display a screen page Error list R S T phase OK or Not OK checking the presence of the mains phases at the controller Fan 1 2 3 OK or not OK checking the rotation of each fan arranged in the top of the cabinet and ensuring air extraction Software version software version present in the Human Machine interface TTD HUMAN INTERFACE HMI Unit When any problem is detected by the cabinet An exclamation mark then appears to the right of the screen page In this case press the exclamation mark to display a screen page Error list 12 3 DMX Information DMX AS start address DMX A DMX B channel value to address cabinet output 1 e x 1 lt x lt 512 not used channel value 0 or gt 512 no circuit physically present in cabinet location 1 or circuit identification error in cabinet location 1 or operating fault DMX ASB present Yes Yes DMX signal reception detected No DMX signal reception missing Patch A B see PATCH menu e Yes the addressing filled in in each patch at the circuits is not in ascending order e No the addressing filled in in each patch at the circuits is in ascending order e g 1 2 3
33. figures the ARTNET universes for the two controllers as well as the subnet and port values ADB www adblighting com User Manual Page 56 Lighting Technologies Issue 1 1 EURODIM TWIN TECH oh Settings artnet XR Universe Artnet SubNet Port 0 3 Gee Universe 2 Artnet SubNet 4 Port 1 Universe 3 Artnet SubNet Port 2 37 1 Selecting Universe Mode For each universe choose the operating mode Not Used mode the universe is not taken into consideration for the control of the circuits ARTNET mode the universe is taken into consideration for the control of the circuits Touch to select the mode The mode selected must be highlighted 37 2 Subnet and Universe Port For each universe fill in the subnet and the port such that it is identical to the configuration of the control console Subnet and port value between 0 and 15 Position on the subnet value port either by touching the screen or using the wheel The value is highlighted Type the value using the keyboard Validate the value by touching the screen to select the zone in question or using the wheel 38 Synchronisation Menu This function is used to perform a copy operation between the controllers in the event that a new CTRL blank or containing old data is put in place in the cabinet ADB www adblighting com User Manual Page 57 Issue 1 1 Lighting Technologies EURODIM TWIN TECH Data
34. function 19 1 Range Key Used to attribute the same intensity to a set of circuits included within a range Edit cue 9z 2 3 im nes From dim To dim oo 1 Intensity 02 ADB www adblighting com User Manual Page 27 Issue 1 1 Lighting Technologies EURODIM TWIN TECH Enter The start dimmer number From dim The end dimmer number To dim The intensity to be attributed to these circuits Confirm with the OK button Note the circuit s first number From dim must be lt the circuit s second number To dim during definition of the range Otherwise the range between two circuits cannot be validated The ALL key is used in order to directly enter the 128 circuits of the cabinet 19 2 Time Exist Key Used to attribute an intensity rise time for all of the circuits when a cue is played Used to attribute a wait time This function will be used when the chaser is played See CHASER PLAY sub menu Used to render a cue existing or non existing Edit cue LA RE CueNo O E Time of cue n 0 Fade time Wait time Enter The fade time minutes seconds The wait time minutes seconds The existence of the cue select yes no Confirm with the OK button Note the maximum time taken into account for the minutes is limited to 99 minutes ADB www adblighting com User Manual Page 28 Issue 1 1 Lighting Technologies EURODIM TWIN TECH 20
35. iagnostic page opens a window and displays Controller synchronisation ADB www adblighting com User Manual Page 41 Lighting Technologies Issue 1 1 EURODIM TWIN TECH e OFF selected the modifications are made but the screen is not changed 30 Load Scanning Menu Important This function can only be used if the sequential diagnostic kit has been installed in the cabinet it being used to measure the neutral current on the module power line busbar This function is used to scan the loads present at the output of each circuit and check that the loads have not changed with respect to a previous state This verification is performed in two stages Learn to define the reference loads present at the output Scan to launch the load verification operation Scan Loads A i LEARN SCAN 31 Load Scanning Menu Learn Important This function can only be used if the sequential diagnostic kit has been installed in the cabinet it being used to measure the neutral current on the module power line busbar This function is used to define the reference loads present at the output of each circuit ADB www adblighting com User Manual Page 42 Lighting Technologies Issue 1 1 EURODIM TWIN TECH Possibilities EDIT SCANNED PRESENT REF 213 7 2 4 8 NoLoad After start up the following information is available There is no load present in the EDIT column left hand column The infor
36. ies EURODIM TWIN TECH Important note The scan can only be conducted if there is no sinewave module present in the cabinet even if it is not selected for the scan The sinewave modules need to be removed from the cabinet before launching the scan The result of the measurement appears in the MEASUREMENT column The following information can be found Load value No load Overload There is an overload if for a module of 3KW a load gt 4KW has been measured fora module of 5KW a load gt 7KW has been measured The circuit currently being scanned is automatically highlighted This function vanishes as soon as you use the dial or select another output on the touchscreen To find this function press the number 6 on the numerical keyboard When the load scan is completed we can verify the differences in the table between the modules recorded left hand column and the load values measured right hand column The sign appears in the central column in the event of an inconsistency 33 Module Measurements Menu This function displays the values measured for the sinewave and thyristor modules with a full diagnostic option au j Module measurements 3 Gee Module 1 Circuit 1 Technology Thyristor without diagnosis C Only the sinewave or thyristor fluo modules with full diagnostic option can give measurements or diagnostic The fluo and thyristor modules without this diagnosis will a
37. in the event that an error is detected and displayed in the diagnostic screen page ADB www adblighting com User Manual Page 49 Issue 1 1 Lighting Technologies EURODIM TWIN TECH a Modules diagnosis 3 Gre Module 1 Circuit 1 Circuit 1 NZA Circuit 3 NZA Circuit 2 NZA Circuit 4 NZA Detail of circuit 1 OSSR A 34 1 Selecting the modules and circuits To select a module or circuit position on the module or dimmer number highlighted either by touching the screen or using the wheel To display the module or circuit measurements Touch the screen to select the zone of the number in question or use the wheel Type the number using the keyboard Validate the number by touching the screen to select the zone in question or using the wheel Otherwise press keyboard key 1 to scan the modules circuits in ascending order or press keyboard key 0 to scan the modules circuits in descending order The first frame provides a summary of the functional status of each of the circuits constituting the OK or Not OK module In the event of a problem detected on a circuit display the circuit to obtain more details on the malfunction The second frame is the detail for each of the circuits constituting the module ADB www adblighting com User Manual Page 50 Lighting Technologies Issue 1 1 EURODIM TWIN TECH Information displayed for each circuit according to the module type Thyristor p
38. ircuits present in the cabinet The figure in the right hand column is the channel attributed in the DMX signal Select patch A or B to start with Use the wheel to rapidly move between all the rows of the patch The row selected is highlighted To attribute a channel position on a row and use ADB www adblighting com User Manual Page 18 Issue 1 1 Lighting Technologies EURODIM TWIN TECH The touch screen and the numeric keyboard to enter a value Press key 1 directly to increment the value by 1 between 1 and 512 in relation to the first value available on a previous row Press key 0 directly to decrement the value by 1 between 1 and 512 in relation to the first value available on a previous row The Range key in order to enter values between two circuit references Important Specific case for row 1 1 if key O or 1 is used the value taken into consideration corresponds to the content of output 128 if available otherwise output 127 and so on If the value entered is 0 or greater than 512 the circuit is not controllable and the message Not used is displayed 15 1 Range Key Used to attribute an ascending patch value in graduations of 1 to a set of circuits included within one section 8 0 Patch DMX LEA eae 3 Ge ay oe Lu ro a rm ee mM ro mh AB Enter The start dimmer number From dim The end dimmer number To dim The start channel
39. isplayed in the EURODIM Twin Tech Frame ccccccccccceceseeceeeeeeees 60 39 3 List of Errors displayed in the CTRL Board Frame 60 39 4 List of Errors displayed in the Modules Frame 60 A0 Fault Clearing CN ee 2 ese ee eect eee he teed 61 40 1 Procedure to be followed in the Event of an Error 62 ADB www adblighting com User Manual Page 2 Issue 1 1 Lighting Technologies EURODIM TWIN TECH 1 Foreword This user manual relates to the human machine interface HMI or TTD HUMAN INTERFACE present on the EURODIM Twin Tech plug in dimmer cabinet The present manual describes the functions developed in the software version 5 060 This manual will help you configure your Twin Tech cabinet following the initial installation of your equipment or when changing or adding a module within your cabinet Important note The present manual does not describe the functions relating to the ADB service menu This menu is dedicated to qualified personnel trained by the hardware supplier and to the ADB Lighting Technologies technical department Read this guide attentively before using the interface Important the screen pages available in this manual are provided for information purposes only and are subject to modification by ADB at any time ADB www adblighting com User Manual Page 3 Lighting Technologies Issue 1 1 EURODIM TWIN TECH 2 Description of the Unit The user is provided with 1 A backlit LCD touch s
40. l values in the event that the DMX and or ARTNET signals is not present See PRIOR DMX FAIL sub menu According to the human interface hardware version installed on the cabinet it is possible for only the emergency cue no 0 to be available ADB www adblighting com User Manual Page 25 Issue 1 1 Lighting Technologies EURODIM TWIN TECH Several sub menus are available Cue Edit Enter the cue content Cue Capture Capture the DMX ARTNET signals in a cue Cue Play Control the circuits by playing a cue Cue Copy Copy the content of one cue to another cue Cue Erase Erase a cue s content Cue PRIOR DMX FAIL Select a source to replace a absence of DMX ARTNET Chaser Play all existing cues on loop 19 Cues Menu Edit This function is used to fill in the content of the 80 cues cue 0 A control intensity is allocated to each of the 128 circuits constituting the cabinet Edit cue Cue 3 number 1 INN Existing cue 1 2 2 02 143 3 02 1 4 4 02 d l 9 FF e 2 6 FF 4107 244 8 02 243 The sign E signifies that the cue exists and that it may be played See PLAY sub menu A cue can be made existing or non existing If it is non existing it may not be played and will not be included in the chaser See Time Exist key Cue 0 always exists but it will not be played in the chaser Selecting a cue To select a cue to be edited position o
41. lways give N A not available ADB www adblighting com User Manual Page 48 Lighting Technologies Issue 1 1 EURODIM TWIN TECH Information displayed according to the module type circuit technology Sinewave thyristor fluo with or without diagnosis input V voltage measured at the module input identical information for the four circuits Voltage in V output V Voltage measured at the output of each circuit Sinewave module always N A output Output current per circuit Sinewave and Thyristor modules with Diag measurement A accurate to one decimal point Controller vers Module software version Controller sec vers Indication available only for sinewave modules 33 1 Selecting the modules and circuits To select a module or circuit position on the module or dimmer number highlighted either by touching the screen or using the wheel To display the module or circuit measurements Touch the zone of the number or use the wheel Type the number using the keyboard Validate the number by touching the screen to select the zone in question or using the wheel Otherwise press keyboard key 1 to scan the modules circuits in ascending order or press keyboard key 0 to scan the modules circuits in descending order 34 Modules Diagnosis Menu This menu is used to verify the operation of the modules and obtain detailed information on the operation of each circuit It is useful
42. mation displayed in the MEASUREMENT column is unknown The DIFF column is used to check whether the information in the left hand and right hand columns is the same or different or The load connected at the output of each circuit can be defined manually or automatically 31 1 Manually selecting the loads To select a circuit position on the row highlighted either by touching the screen or using the wheel To edit and select a load Touch the screen to select the row or use the dial A table featuring all the available loads is displayed Select a load value present in the table either by touching the screen or using the wheel Validate the selected load by touching the screen to select the value or using the wheel The load value is displayed in the EDIT column ADB www adblighting com User Manual Page 43 Lighting Technologies Issue 1 1 EURODIM TWIN TECH ea Learn loads Dimmer No 11 31 2 Range Key Used to attribute the same load value to a set of circuits included within a range F Learn loads SSS RANGE All From dim 1 To dim 32 3 Gre E LOAD 3 ki on Car ADB www adblighting com User Manual Page 44 Issue 1 1 Lighting Technologies EURODIM TWIN TECH Enter The start dimmer number From dim The end dimmer number To dim The load to be attributed to these circuits a table appears enabling the load to be selecte
43. n the cue number highlighted either by touching the screen or using the wheel ADB www adblighting com User Manual Page 26 Lighting Technologies Issue 1 1 EURODIM TWIN TECH To edit the cue number Touch the screen or use the wheel to select the zone of the number in question Type the number using the keyboard Confirm the cue to be edited by touching the zone or use the wheel Otherwise press keyboard key 1 to scan the cues in ascending order or press keyboard key 0 to scan the cues in descending order Important When a cue is edited there is a loading time The status row at the bottom of the page informs the user of this status Wait for the synchronisation to be complete in order to obtain a correct reading of the intensities of each of the cue s circuits Attributing intensity To attribute a control intensity position on a row using the wheel Touch the zone where the intensity is displayed in order to edit the value Enter the value using the numeric keyboard between 0 and 100 Touch the zone where the new value is displayed in order to validate To identically recopy the intensity of the preceding circuit use keyboard key Note If the value attributed is 100 the screen displays FF Any value entered that is beyond 100 is limited to 100 Any value entered into a non existing cue will render it existing The backup validation of the intensities is conducted upon leaving the cue or
44. nical service only Synchro to synchronise the parameters recorded between each of the controllers ADB www adblighting com User Manual Page 17 Lighting Technologies Issue 1 1 EURODIM TWIN TECH Note All the information displayed in the different menus originates from controller 1 if two controllers are present in the cabinet If only controller 2 is present all the information displayed in the different menus will originate from the latter When changing the patch power multiplication factor law the new data is sent to each controller The cirsuits defined as empty slot or undefined slot are not editable and not visible in any screens It appears again when the circuit will not be declared as empty slot or undefined slot 15 Patch Menu This function is used to configure a patch on a circuit or set of circuits for the DMX A and DMX B signal This configuration enables the user to attribute the value of a DMX A and DMX B signal channel to the control of one of the cabinet s circuits 880 Patch DMX oe CRE RC 3 Cr 880 Patch DMX Be I ess 3 Ge 4 Module reference ne TE en sf CO CS ETES ENS channel Ces Cre Cor Reminder The referencing of the modules in the cabinet starts at 1 in relation to the first location located at the top of the cabinet up to 32 The left hand column contains the referencing of the modules and c
45. p of the cabinet up to 32 The left hand column contains the referencing of the modules and circuits present in the cabinet Example Value 1 1 references module 1 circuit 1 of the module The right hand figure indicates the output on the cabinet from 1 to 128 ADB www adblighting com User Manual Page 22 Issue 1 1 Lighting Technologies EURODIM TWIN TECH Module identification All the modules are fitted with an EEPROM cue which contains an ID code When the modules are installed in the cabinet this ID is communicated to the controller This information is available in the Present column In this column the following information can be obtained a correct ID or Undefined slot for a module that is unidentified by the controller or uninstalled TD4x3 M R TECHNOLOGY S sinewave standard with diagnostics only with 3R or 4R T thyristor dimmer with 400yus rise time P thyristor dimmer with 200us rise time F Fluo dimmer with 200us and remote controlled preheat R DimSwitch with 200us rise time H DimSwitch with dual 200us 400us rise time standard with diagnostics N Non Dim no remote control D Full diagnostic version optional Number of circuits in the module Rated Load in kW of each circuit in the module MN MCB with 1P N protection RCD protection No RCD 1R per module 2R 2 individual protections Fluo 3R 3 individual protections 4R 4 individual protections EUROD
46. r application of the law in the same units LINEAR 1 V120 2 FLUO 3 PREHEAT 4 SQUARE 5 TV 6 BBC 7 SWITCH 8 Tv2 9 VRT 10 ADB www adblighting com User Manual Page 12 Issue 1 1 Lighting Technologies EURODIM TWIN TECH 11 Presentation of the Home Page Lighting Technologies DMX START ADDR OMX l OMX B le ARTNET START ADDR Universe 1 100 Universe 2 200 Universe 3 Click here to continue This screen page is displayed as soon as the cabinet is switched on It gives the information concerning the start address for the DMX A and B inputs and the three ARTNET universes Information available for start address valid for DMX and ARTNET x channel value to address cabinet output 1 1 lt x lt 512 not used channel value 0 or gt 512 no circuit physically present in cabinet location 1 or circuit identification error in cabinet location 1 or operating fault To access the diagnostic page press the arrow ADB www adblighting com User Manual Page 13 Lighting Technologies Issue 1 1 EURODIM TWIN TECH 12 Presentation of the Cabinet Diagnostic Page This screen shows the cabinet diagnostic information 3 Gre CTRL 2 ctrl board active YES frequency 50 hz hardware communication OK software version 5 060 temperature OK CTRL INFO EURODIM TT INFO Ref module
47. rature now longer exceeds the threshold set Note The measure be different between the 1 circuits and the circuits Thyristor with diag always N A Main voltage Sinewave 1 Displays OK Cases 2 and 3 do not trigger a module error as it is the main voltage that is incorrect 2 Displays Too high 3 Displays too low Note If the main voltage lt 205 V the sinewave module no longer controls its circuits Thyristor always N A Controller vers Module software version Sec vers Controller Indication available only for sinewave modules ADB Lighting Technologies www adblighting com User Manual Page 52 Issue 1 1 EURODIM TWIN TECH 35 ARTNET Patch Menu This function is used to configure a patch on a circuit or a set of circuits for each of universes 1 2 and 3 This configuration is used to attribute the value of a channel of each universe to the control of a circuit of the cabinet ee Universe reference channel Patch Artnet Patch Artnet 223 3 Ge m Ee ie UNIVERSE 1 UNIVERSE 3 1 if i efi a 23 7 16 Reminder The referencing of the modules in the cabinet starts at 1 in relation to the first location situated at the top of the cabinet up to 32 The left hand column contains the referencing of the modules and circuits present in the cabinet Example Value 1 1 references module 1 circuit 1 of the module The right hand figure indicates th
48. rement inside the controller is outside the operation range Control 9 V error explanation the control 9 V power measurement is outside the operation range 1V2 error explanation the internal 1V2 power measurement is outside the operation range Frequency error explanation the mains frequency measured at the controller input is different from the frequency configured in the TTD HUMAN INTERFACE HMI Software version error explanation the software to be found on the controller processor 1 processor 2 processor 3 and that in the TTD HUMAN INTERFACE HMI Unit are not identical In all of these cases only ADB technical personnel can intervene 39 4 List of Errors displayed in the Modules Frame x module s different The modules actually present in the cabinet are not those used for dimming Displays the number of different modules detected Explanation difference between the reference column and the column present on the CONF POWER screen Press the CONF POWER button that appears next to the error This provides a shortcut to the CONF POWER menu Press the REF gt PRES button in order to copy the list of modules present in the REFERENCE column Error on the x y module s only for the Sinewave or Thyristor Fluo modules with full diagnostic option Explanation Operating error detected on one or more modules Displays the number of modules where an error has been detected For more information press
49. ributed to a circuit is the switch law the multiplying factor is forced to 100 FF by the software 16 1 Range Key Used to attribute the same law and the same multiplying factor to a set of circuits included within a range Hultipiying Fact ultiplying Factors _ sis T RANGE All From dim To dim Law Mult fact ADB www adblighting com User Manual Page 21 Issue 1 1 Lighting Technologies EURODIM TWIN TECH Enter The start dimmer number From dim The end dimmer number To dim The law to be attributed to these circuits The multiplying factor to be attributed to these circuits Confirm with the OK button Note the circuit s first number From dim must be lt the circuit s second number To dim during definition of the range Otherwise the range between two circuits cannot be validated The ALL key is used if we wish to enter the cabinet s 128 circuits directly 17 Power Configuration Menu This function configures the module type depending on its position in the cabinet FA Config Power FA Config Power 36 3er Module type J Modulen 1 REF lt PRES COMPARE Undefined Slot Used Modules Empty Slot REFER P4x3 MN P4x3 M PRESENT Lew Reminder R4x3 MN R4x3 M F2x3 MN P4x3 MN 1R P4x3 M 1R R4x3 MN 1R The referencing of the modules in the cabinet starts at 1 in relation to the first location situated at the to
50. s are used for dimming dmx a start addr 1 dmx b start addr 12 dmx a present YES dmx a fail cue dmx b present YES dmx b fail black Crew Cover Cr patch a NO patch b NO Diagnosis of the cabinet phaser OK fan 1 OK phases OK fan 2 OK phase t OK fan 3 OK HMI Y 5 060 DMX INFO Diagnosis of the cabinet 3 Gre CTRL INFO ctrl board active YES frequency 50 hz hardware communication OK software version 5 060 temperature OK EURODIM TT INFO Ref modules are used for dimming phaser OK fan 1 OK phases OK fan2 OK phaset OK fan 3 OK HMI Y 5 060 DMX INFO dmx a start addr 1 patch a NO dmx b start addr 42 patch b NO dmx 3 present YES dmx a fail cue dmx b present YES dmx b fail black Crew Cover Cee This page is divided into three zones Azone CTRL1 or CRTL2 tab providing information on the controllers A zone EURODIM TT INFO providing general information on the cabinet s operation identification of the modules by the controller and signalling the alarms Azone INFO DMX providing information on the DMX inputs and the functions associated with these inputs Two keys enable the user to Access the two menu screen pages MENU key To access the Menu when prompted by a specific window the user access code needs to be entered using the keyboard without validating Access the ARTNET information ENET key This page is accessible regardless of the
51. t menu Linear V120 Fluo Preheat Square Tv BBC Switch Tv2 VRT as well as six user defined laws enabling free configuration by the user Important notes The user defined laws 1 to 6 are configured by default in order to apply the Linear law The six user laws are only editable via the optional TTD Management Software Switch law presented in the form of a hysteresis with a transition from 0 to 255 at 15 and transition from 255 to 0 at 12 see switch curve 10 2 Applications of Laws on Specific Modules 10 2 1 Fluo Module TTD F The first two outputs are used for the dimmer The law of one s choice is applied here The last two outputs are used for the preheat the switch law ON OFF shall be used The maximum ambient temperatures are defined in the EURODIM Twin Tech data sheet Mult Fact Multiplication Factor or Reduction of the maximum possible output level of a dimmer circuit ADB www adblighting com User Manual Page 11 Issue 1 1 Lighting Technologies EURODIM TWIN TECH 10 2 2 Module DimSwitch with Dual filtering TDD HD When the user chooses the switch law the circuit is automatically configured with a filtering characterised by a 200 us rise time For all other laws the circuit uses a filtering characterised by a 400 us rise time The rise time is 400 us by default Law curve giving the relationship between the DMX input 0 to 255 of the function law and the output afte
52. t using the cabinet selector Stop the cabinet and proceed with replacing the controller Temperature error Refresh the room Automatic reduction of temperature the circuit control value See chapter cabinet fan until the temperature is acceptable Frequency error Verify the mains frequency at Poor circuit control the cabinet s input Verify the operating frequency selected in the software ADB service menu outputs flash Software version error Change the faulty CTRL or reload the software from the TTD HUMAN INTERFACE HMI ADB service menu The maximum ambient temperatures are defined in the EURODIM Twin Tech data sheet ADB Lighting Technologies www adblighting com User Manual Page 62 Issue 1 1 ADB Your Partner for Light Belgium France N V ADB TTV Technologies S A ADB S A S Group Headquarters Leuvensesteenweg 585 B 1930 Zaventem Tel 32 2 709 32 11 Fax 32 2 709 32 80 E Mail adb adblighting com Sales Office 92 Avenue Jean Jaur s F 92120 Montrouge Tel 83 1 41 17 48 50 Fax 33 1 42 53 54 76 E Mail adb fr adblighting com Factory amp Group Logistics Centre Zone industrielle Rouvroy F 02100 Saint Quentin Tel 83 3 28 06 35 70 Fax 33 3 23 67 66 56 E Mail adb fr adblighting com www adblighting com MAUA 7 106 53 10 ADB Lighting Technologies Subject to modifications M 3213 E 01r
53. t addr 12 patch b NO dmx 3 present YES dmx a fail cue dmx b present YES dmx b fail black Crew Cover Coa 39 1 Errors List Screen Page Errors list A 3 Be Eurodim TT CTRL BOARD Modules ADB www adblighting com User Manual Page 59 Issue 1 1 Lighting Technologies EURODIM TWIN TECH The two CTRL1 and CTRL2 keys are used to display the errors detected by each controller Indeed each controller can display different errors in the CTRL frame in particular Touch one of the two keys to display the error messages 39 2 List of Errors displayed in the EURODIM Twin Tech Frame 1 2 Displays an error on a mains phase example phase r error Explanation the voltage measured at the controller input is outside the operation range Displays an error on a cabinet fan that is not functioning example error FAN 1 39 3 List of Errors displayed in the CTRL Board Frame 1 Da 3 9 CTRL error explanation there are three processors in each controller Processor 2 or 3 is not responding In this case no dimming will be possible on this controller Comm error the controller is not responding to TTD HUMAN INTERFACE HMI messages 24 V error explanation the 24 V power measurement inside the controller is outside the operation range Temperature error explanation the temperature measured in the controller is not acceptable 9 V error explanation the 9 V power measu
54. t the cabinet Ethernet orange Flashes Communication ensured with the network Ethernet orange Off No communication with the Verify the connection at the network cabinet Alarm red Solid Alarm detected See diagnostic screen DMX A B ENET Flash Controller operating error Switch the cabinet off on at ALARM the mains to remove the error where applicable ADB www adblighting com User Manual Page 61 Lighting Technologies Issue 1 1 40 1 Procedure to be followed in the Event of an Error EURODIM TWIN TECH Errors list Action Downgraded mode r S t phase error Verify the external network Verify the connections on the cabinet Verify the main breaker in the cabinet Verify the CTRL fuses The modules connected on the faulty phase are no longer useable Fan 1 2 3 error Proceed with replacing the cabinet s faulty fan Risk of an increase in the temperature inside the cabinet See temperature error Controller error Switch the cabinet off on at the mains to remove the error where applicable Switch to the controller if present using the cabinet selector Stop the cabinet and proceed with replacing the controller Communication error Verify the connections TTD HUMAN between the TTD HUMAN INTERFACE HMI will INTERFACE HMI and the no longer be cabinet synchronised with this controller 24 V 9 V 9 V control and Switch to the controller if 1V2 error presen
55. the LAWS serment bee sue ntm 11 10 2 Applications of Laws on Specific Modules c ccceeeeeeeeeeeeenneeee tree eeeecenaaeeeeeeeeeeteeea 11 10 21 Fluo Module CUDA SSSR en ue 11 10 2 2 Module DimSwitch with Dual filtering TDD HD 00 eee ceeeeeee eter ee eeeeennneeeeeeeees 12 11 Presentation of the Home Page lester eee 13 12 Presentation of the Cabinet Diagnostic Page 14 12 1 Controller CTRL Information as esevescestciare sted apenete nn NN nan 14 12 2 EURODIM Twin Tech Information 5 cxcaceietwentecsencacptavasasecacetavpietatavetsentaceta caeacecacetacpiasaine 15 12 3 DMX Information scccacccaxeatceeneiacccsuntatzdencsaasecuxsateesrcasascesxaatacensiauseeitaatnesieasaseesxaaindesstarsies 15 13 Presentation of the ARTNET Information Page nnnnnsssnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnn 16 14 Description of the Menus sssssnnnnnenennnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnn nnmnnn nne 17 10 Pateh Men nina an aan ann a ane en n anne nent ananas 18 15 1 Range EEE 19 152 PBIB a arate seat meet etree 20 16 Laws and Multiplying Factor Menu rene 20 16 1 ARR gate ae een ne ee eee Ee ee eer eee ee er rer eee ere 21 17 Power Configuration Menu ses leniesseneiennienetene 22 17 1 CONIPARE RON nn ia arenes bates 23 17 2 Pe PRES RON nes an nee 24 17 3 AO eer et ere ere eee ere a eee 24 19 Cues MOD side asie tienne 25 19 Guess MOD d T a ecaseses tentes 26 19 1 Range ROY EE E E
56. the MOD DIAG button that appears next to the error This provides a shortcut to the MOD DIAG menu of the module of the first circuit experiencing an error The maximum ambient temperatures are defined in the EURODIM Twin Tech data sheet ADB www adblighting com User Manual Page 60 Lighting Technologies Issue 1 1 EURODIM TWIN TECH Directly displays the first circuit where an error has been detected Verify on which circuit row the error appears e Choose the module to be used The modules used by thee controller do not correspond to those of the REFER and PRESENT columns in the CONF POWER menu in IHM The database is not identical Press the CONF POWER button that appears next to the error This provides a shortcut to the CONF POWER menu Press the REFER button to update the database and delete the error This error can occur when a cabinet s TTD HUMAN INTERFACE HMI is replaced 40 Fault Clearing Guide Each controller is equipped with several LEDs for visual monitoring the information available on the interface Light State Operation Action RUN light green Flashes OK RUN light green Solid or Controller operating error Switch the cabinet off on at off crashing the mains to remove the error where applicable DMX A B Flashes Communication with the console orange DMX A B Off No communication with the Verify the connection with orange console the console a
57. the TTD HUMAN INTERFACE HMI There are several possible user access levels The first two screens home and main screen are accessible to all users An access code needs to be entered in order to access the Menu screen Depending on the authorised access level the user will be able to make modifications or launch functions The table below indicates the functions accessible to the user according to the access level View the parameters Yes Yes Yes Edit the patch Yes Yes Test a dimmer Yes Yes Alter the settings Yes Yes Scan the loads Yes Edit the laws and Yes multiplying factor Edit the ARTNET Yes Yes parameters Manage the Cues Yes Yes Load Save the Yes parameters Manually Yes synchronise between controllers ADB service Level 0 does not allow access to any menu or function Depending on the authorised access level certain functions or menus remain blocked Should you attempt to access these the software will ask you to enter the access code for the next level in order to authorise access to the function or menu The access level indication can be viewed on all the screen pages It is located in the top right hand corner and is signalled by a figure representing the current access level from O to 3 followed by a key symbol 3 Gee ADB www adblighting com User Manual Page 6 Lighting Technologies Issue 1 1 EURODIM TWIN TECH 5 Screensa
58. ting com User Manual Page 34 Issue 1 1 Lighting Technologies EURODIM TWIN TECH Controller 1 Controller 2 Example with the Memory 0 with the circuit 1 at 95 DMX A circuit 1 100 Memory 0 circuit 1 95 DMX B circuit 2 0 Circuit 1 95 DMX A circuit 1 90 Circuit 2 100 DMX B circuit 2 100 Select one of the possibilities by touching one of the keys 25 Cues Menu Play Chaser This function is used to link up the play of all existent cues except cue 0 EF Play chaser Cues in the chaser 1 Status m The list of cues played is displayed in the window Press the PLAY key to launch the chaser The cues are played in ascending order Press the Stop key to interrupt the chaser The DMX ARTNET signals once more control the circuits The chaser may not be replayed immediately after a stop It is necessary to wait for five seconds before the chaser can be launched again ADB Lighting Technologies www adblighting com User Manual Page 35 Issue 1 1 EURODIM TWIN TECH DMX gt CHASER Cue 1 2 gt DMX Intensity 4 CMD PLAY CHASER WAIT Cue 1 WAIT Cue 2 Time DMX Fading CUE 1 Fading CUE 2 Cue 1 Cue 2 26 Overview This function displays all parameters in modules see View all parameters 3 Cr Module 1 Output 1 Power info T4x3 MN 4R Circuit qty ADB www adblighting com User Manual Page 36 Issue 1 1
59. umn position on the module using the wheel Touch the module zone leading the module ID table to appear Touch to select a reference from the table the reference selected is highlighted Touch the highlighted reference to validate and attribute to the module 17 3 Range Key Used to attribute the same ID to a set of modules included within a range FA Config Power Module type 3 Gee From mod To module Power R4x3 MN TR ADB www adblighting com User Manual Page 24 Lighting Technologies Issue 1 1 EURODIM TWIN TECH Enter The start module number The end module number The ID to be attributed to these modules Confirm with the OK button Note the module s first number From module must be lt the module s second number To module during definition of the range Otherwise the range between two modules cannot be validated The ALL key is used in order to directly enter the cabinet s 32 modules A window opens when we exit the menu after a change has been made to a module s reference in a given location The user is invited to go to the patch menu if necessary 18 Cues Menu EDIT CAPTURE PLAY COPY ERASE PRIOR OMX FAIL Chaser 80 cues 1 emergency cue cue no 0 are available to record pre defined circuit control values These cues can be played A special emergency cue bearing the no 0 is available to replace the circuit contro
60. user access level 12 1 Controller CTRL Information Note The information is present if the controller is physically connected and operational in the cabinet CTRL board active e Yes if the controller is selected by the cabinet controller selector position 1 for controller 1 and position 2 for controller 2 or A R for both e No if the controller is not selected circuits not controlled by this controller Frequency displays the network frequency measured at the controller s input ADB Lighting Technologies www adblighting com User Manual Page 14 Issue 1 1 EURODIM TWIN TECH Hardware communication OK if the controller is operating correctly Not OK if a problem is detected In this case an error message and an exclamation mark appear in the EURODIM TT INFO zone Software version software version present in the controller Temperature OK if the temperature measured in the controller is acceptable Not OK if the temperature measured in the controller is too much high In this case the control value of all of the active circuits is reduced by 1 every minute until the temperature measured becomes again acceptable also see paragraph on the operation of the ventilation within the cabinet 12 2 EURODIM Twin Tech Information The first row of information available informs the user via a message that the cabinet and the modules are in operation The message re
61. ut function selected the value of corresponding patches A and B is displayed Adjust in the same manner the output control intensity value row intensity between 0 and 100 FF ADB www adblighting com User Manual Page 38 Issue 1 1 Lighting Technologies EURODIM TWIN TECH the output control duration delay row duration between 0 0 5 secs and 60 secs Touch the screen or use the wheel to select either the manual or automated test Manual test only the selected output associated with a reference module will be controlled with the set intensity Automated test all outputs starting from the selected output will be tested one after the other for the duration and with the set intensity except the channels defined as undefined slot or Empty slot Press the START key to launch the manual or automated cycle Press the same START key to stop the manual or automated cycle 27 2 Flash Tab Touch to select the Flash tab Used to control a circuit with automated variation of the intensity between 0 and the set value To select an output position on the output number highlighted either by touching the screen or using the wheel To edit the output number Touch the screen to select the output number or use the wheel Type the number using the keyboard Validate the output by touching the screen to select the zone in question or using the wheel Otherwise press keyboard key 1 or the
62. value to be taken into consideration for incrementation in graduations of 1 Confirm with the OK button Note the circuit s first number From dim must be lt the circuit s second number To dim during definition of the range Otherwise the range between two circuits cannot be validated The ALL key is used in order to directly fill in the cabinet s 128 circuits ADB www adblighting com User Manual Page 19 Issue 1 1 Lighting Technologies EURODIM TWIN TECH 15 2 A gt B Key Used to copy all of the values from patch A to patch B and make them identical 16 Laws and Multiplying Factor Menu This function is used to attribute a law and a multiplying factor to a circuit or set of circuits See explanation on the curves of the laws in a specific paragraph ae act Laws and ultiplying Factors Multiplying Factors mpa LAWS MULT FACT Circuit No 1 1200 FLUO 1 3 3IL Mid 144 4 120V FF 2 1 SILIN 50 Z 2 2 6 LIN 50 Z Crew nee Can Reminder ial The left hand column contains the referencing of the modules and circuits present in the cabinet Example Value 1 1 references module 1 circuit 1 of the module The right hand figure indicates the output on the cabinet from 1 to 128 In the Laws column we select the law that we wish to attribute to a circuit This choice will depend on the type of load connected at the circuit output Important after validation this action has
63. ver If whilst accessing a screen page other than the home page the user does not handle the touch screen keyboard or wheel for a period of more than one minute the software returns to the home page The access code will become 0 To access the Menu screen pages an access code will again need to be entered 6 Online Assistance A HELP key is provided in the bottom right hand corner of all of the screen pages allowing touch access to a help function relating to the page consulted Press the BACK touch button to return to the screen page 7 Menu Tree Structure Screensaver Cabinet diagnosic Patch A amp B Laws M Fact Mem DMX fail Settings Cont Menu 2 ADB www adblighting com User Manual Page 7 Issue 1 1 Lighting Technologies EURODIM TWIN TECH Scan loads measurements ADB Service functions not described Synchronisation 8 Cabinet Configuration The upper part of the Twin Tech cabinet may be equipped with Two Controller units oraController unit and a backup power supply module The Controller units control all of the circuits 128 max constituting the modules available in the cabinet 32 max according to the configuration recorded by the Unit software patch and the channel values present on the DMX A DMX B and ARTNET inputs ETHERNET connection ADB www adblighting com User Manual Page 8 Issue 1 1 Lighting
64. w 50 all the fans are idle Speed 2 is engaged high air extraction when a sinewave module and or a module fitted with four RCBO MCB RCD is present in the cabinet and it is controlled The speed 2 is also engaged if the fans run in speed 1 and the temperature is too much high The speed is held up to that temperature is again acceptable When the conditions described above are no longer met the fans continue to operate for a further five minutes at speed 1 before stopping 10 Initial User Configuration The identification of the modules present in the cabinet is controlled by the Controller 1 This verification is automatic A warning message signals any identification fault or error See Power Configuration menu in the event of an alarm The user must then Define or validate the control of each module s circuits by allocating the DMX channels See Patch ARTNET Patch and ARTNET Configuration menus Define the laws and multiplying factor applicable on each of the circuits constituting a module with respect to the loads that are wired at each circuits output These laws enable each of the loads to be controlled correctly and risk free See Laws Mult Fact menu Define the type of modules to be used in order to dim the light by accepting the list of modules identified by the controller see power configuration menu 10 1 Description of the Laws The following laws are pre recorded and available in the Laws Mult Fac

eurodim twin tech us... - ADB Lighting Technologies

Contents

Download Pdf Manuals

Related Search

Related Contents