User guide - Photo Express GSM user manual
Contents
1. _ E A A ee ee oe p i ROY j F d aa p 4 a 4 S al E a a VIO ul si p bef ua hy Ses Ses ss ee V aa z LT J aise F oF a _ insert a SIM card a ALPHA ARSENAL LLC ease the battery pins 104 20 Queens Bivd Suite 1B Forest Hills NY 11375 US send set up a SIM card number Tel 1 718 440 3281 Tel 1 718 355 9281 E mail info alpha safe com m hh press the 7 remote controller button _ Web site www alpha safe com E install the device in a suitable location www alpha safe com EXPRESS GSM MOTION DETECTOR EXPRESS E3 OPERATING MANUAL CONTENTS 1 DESCRIPTION AND FUNCTION 1 1 Purpose 1 2 Technical specifications 1 3 Motion Detector package contents 1 4 Motion Detector structural design 1 5 Keychain Remote Controller structural design 1 6 Device set up and operation 2 SET UP PROCEDURE 2 1 Preparing the device for operation 2 2 Setting up the Motion Detector 2 3 Entering the programming mode 2 4 Erasing the phonebook and SMS messages 2 5 Initial programming set up 2 6 Adjusting the settings 2 7 Adding a telephone number for notification messages 2 8 Erasing notification message telephone numbers 2 9 Erasing a Keychain Remote Controller 2 10 Installing the Motion Detector 2 11 Arming and disarming the Motion Detector device 3 Troubleshooting 4 Contact Information 5 Warranty Coverage EXP2. see tel user manual 4 Take action to determine reason for no GSM network access a Change the location of the MD for better GSM network reception in accordance with installation instructions described in 2 10 of this manual Change the mobile operator used in the Motion Detector Install a new battery 1x CR2032 3v Lithium EXPRESS 4 Contact Information i ALPHA ARSENAL LLC 104 20 Queens Blvd Ste 1B Forest Hills NY 11375 US T F 1 718 440 3281 1 718 355 9281 Skype alpha arsenal E mail info alpha safe com support alpha safe com Website www alpha safe com 5 Warranty Coverage The warranty period is one year from date of purchase During the Warranty period the manufacturer will repair exchange adjust or replace at its discretion any defective product This warranty does not cover damage resulting from any unauthorized attempts to repair or from any use not in accordance with the instruction manual The warranty does not cover physical damage of any kind whatsoever nor does it cover damage caused by any attempt to tamper with or disassemble the product The warranty coverage does not extend to the batteries The warranty period commences on the day first purchased from the manufacturer or an authorized reseller as evidenced by a purchase receipt Without a valid purchase receipt the manufacturer is relieved of its obligation to provide warranty service 20 01 21 2013 EXPRESS EXPRESS FOR NOTES F
3. Camera adjustments delay 17 Armed reset 19 Arming time Interval delay 18 Alarm notification type 28 E malll Fig 8 Settings and values SMS After transmitting an SMS containing settings and values the Motion Detector resets to the Disarmed mode Set up verification 1 Press the A button on the Remote Controller The indicator diode will flash yellow then red and the Motion Detector device will emit a single confirmation beep The Motion Detector will continue to emit beeps for 40 seconds during which time the protected zone must be vacated e g exit the room 2 Wait for an SMS message to arrive containing the text Armed RC 1 Home 3 Wait 2 3 minutes and then enter the protected zone 4 Wait for an SMS text message to arrive containing ALARM Home and for a telephone call from the Motion Detector 5 Place a telephone call to the Motion Detector telephone number within 30 seconds 6 Wait for an SMS text message to arrive containing Disarmed via call from 1XXXXXXXXXX Home 7 Check your e mail for a photograph sent by the Motion Detector device 2 6 Adjusting the settings The settings that were installed during the initial power up are adjustable The setting values can be changed utilizing three methods First method The settings can be changed by using an online service such as hitp express alpha safe com en2 index php or by using the Express GSM Configurator available for download in both A
4. and the E mail at cell 28 see chart 4 Should the registration of additional notification telephone numbers be required see 2 7 5 Press the button on the Remote Control in order to register it in the SIM card memory This Remote Control will be registered at cell 8 RC 1 see chart 4 During the registration process the indicator on the Remote Control will alternately flash red green At the conclusion of the registration process a beep is heard and the indicator light on the Remote Control will turn off In order to register additional Remote Controls repeat instruction 4 for each Remote Control 6 In order to shorten conclude and exit the programming mode press the button on the Motion Detector circuit board for 1 2 seconds prior to the 3 minute conclusion beep or press the F button on the Remote Control 7 The primary designated notification telephone number will receive an SMS message containing the settings see fig 8 In the event you were not able to complete all the operations e g send the SMS and register the Remote Control remove the batteries wait 2 minutes and repeat the procedure from the beginning 13 EXPRESS Recelved from 17180000000 aaa sera 1 Primary notification tel number 1 17180000000 7 2254 8 RC 1 8 RC number 14 Time Interval for test 7 Balance Inquiry status notifications 25 Alarm sound offion ch Serai economy 16 Send SMS ne signal armed disarmed 20 Notification 26
5. card memory see 2 4 Caution While handling and working with the Motion Detector fake care not to touch the camera lens with your fingers fig 1 Touching the fens may result in poor picture quality 9 EXPRESS 2 2 Setting up the Motion Detector At the initial power up using a new or an erased reformatted SIM card see 2 4 the Motion Detector will create an entry in accordance with chart 4 Motion Detector settings 1 26 are stored in the SIM card memory and settings 27 31 are stored in the memory of the Motion Detector device Chart 4 Motion Detector Settings p has Cell label Default Description Description 1st telephone number Enter number in the following primary for notification fomai tg sms g 17 180000000 Enter number in the following format 1 kokki ik kkk e g 17180000000 Available values A balance Auto detection of balance inquiry USSD inquiry telephone number manual entry of tel is possible e g 225 8 RC 1 000000000 EE o Unique individual Remote 10 RCA 000000000 Control ID number On RG while in progeamming 11 Rc 4 000000000 000000000 value defines oge P ooramming 12 RC 5 000000000 RC as not registered aa eae T aonooooon TEST Time interval for test Sets time interval for test status SMS notifications status SMS notifications Interval sets in days hrs amp min up to 30 days using two digits e g 2 every 2 days 12 12 o clock 40 40
6. min 0 test status notice not to be sent pep Fl disarmed mode activated 2 send Reset time interval after a Interval parameter must be triggered Alarm After between 30 250 seconds sending an Alarm e g 0 one time Alarm notification the Motion 60 seconds Detector pauses for 30 120 seconds 250 seconds prior to re arming A notification that the MD has re armed is Type of Alarm notification 0 Only SMS to 1sms 6sms 1 Call SMS SMS sent to isms then calls placed to all tel numbers followed by SMS transmittal to all remaining tel numbers 2sms Sms FS FS EXPRESS 2 Only determines detection zone amp emits short audio tone SMS not sent amp calls not placed 3 Only calls placed to isms 6sms or ArmDelay Arming delay in seconds Parameter should be between 15 250 sec DisDelay Notification delay after Parameter should be triggered alarm in order between 0 250 sec to facilitate disarming in seconds EcoBat Battery economy mode 0 Battery economy mode Disarms via Remote Control only after triggered Alarm Efficient when the Motion Detector is on guard for long periods without the need for disarming 2 Normal mode Disarming via the Remote Control is TriggerAlarm Turns Motion Detector sound offfon during iggered alarm Camera Camera Adjustments four Value digit 1 value digits Image resolution 1 320 x 240 2 640 x 480 Value digit 2 Image type 1 Mo
7. mode after an alarm by using a keychain Remote Control The Motion Detector sends an SMS Disarmed RC1 Home 18 3 Troubleshooting Chart 5 Troubleshooting No sound beeps and GSM light diode flashes on the Motion Detector after installing batteries When Arming Disarming Pressing buttons A or B on the Remote Control no response from the Motion Detector RC light diode glows yellow no red or green flashes see chart 3 At Motion Detector power up Battery installation the GSM light diode frequently flashes but does not enter the 1 flash every5 seconds mode SIM card not registering on the network When pressing the buttons on the RC no flashing lights and no sounds in accordance with chart 3 1 Batteries incorrectly installed 2 Dead batteries No connection with the RC because the distance with the Motion Detector exceeds 15m 5Oft 1 No SIM card installed 2 SIM card improperly installed 3 SIM card PIN code locked 4 GSM inaccessible network Dead battery 19 B Bs EXPRESS 1 Remove amp properly re insert the batteries check polarity 2 Install 2 new batteries AA LR6 1 5v Reduce the distance to the Motion Detector without violating the protection zone 1 Verify the presence of a SIM card 2 Remove the SIM card and re install as shown in Fig 7 of this manual 3 Turn off the PIN code request mode on the SIM card using a GSM telephone
8. service providers Request remaining balance using the RC Controlled via a mobile telephone The Motion Detector performs the following functions Determines human movement in a protected zone Places an alarm call and transmits an SMS text alarm E mails a photograph via GPRS Sends a SMS text message confirming armed disarmed alarm mode Sends a remaining balance status SMS 1 2 Technical specifications Basic technical specifications are shown in chart 1 Chart 1 Basic Technical Specifications Parameter Description Maximum distance at which human presence is determined Maximum RC operating range Maximum distance required to photograph with no lighting Trigger time required to activate camera after penetration Quantity of photographs at penetration GSM module operating standards Maximum number of telephone numbers to be notified EE E _ _ Maximum number of RC units for arming disarming Oooo ee Elapsed time for notification Battery type Un interrupted operating duration using one set of batteries upto6months Quantity of dispatched photographs via e mail during un interrupted up to 60 operation 10c 50c Operating temperature range Relative humidity at a temperature of 35c without moisture condensation not to exceed Operating duration at a temperature of 25c upto6months Overall dimensions The Motion Detector can operate under temperatures as low as 25c with a reduction in the un
9. OR NOTES 21 22
10. RESS oon nr ae wo N N ei b h h m oo onxwweeeniu Pie oD O EXPRESS Dear Customer Thank you for choosing our state of the art high tech security product In order for this product to serve you for a longtime please familiarize yourself with this operating manual In the event that you would like to make any suggestions or comments please do not hesitate to contact us by using the information located at the back of this manual Your opinion is important to us This Operating Manual was specifically written in order to cover all aspects of EXPRESS E3 installation and operation FS EXPRESS 1 DESCRIPTION AND FUNCTION 1 1 Purpose This EXPRESS E3 GSM Motion Detector further referred to as Motion Detector was specifically designed to detect penetration of a protected zone and to transmit notification via a call and SMS text message to a GSM standard telephone also to photograph the penetrated protected zone and transmit an E mail via GPRS EXPRESS E3 Motion Detector features Installs in any location that has GSM mobile service Arms and disarms the alarm via a three button Keychain Remote Control BN 3S further referred to as RC Configures by mobile telephone an online service or an iOS Android app Express GSM Configurator Operates on two AA batteries for up to six months Power saving economy mode available Automatically detects remaining balance and GPRS settings four major
11. beeps programmed flashes Enter armed mode briefly glows red Enter disarmed briefly glows green mode Waiting for MD briefly glows yellow 1 beep to confirm armed disarmed mode Remaining flashes yellow balance inquiry via F button EXPHESS Notifications The Motion Detector transmits an armed disarmed status SMS message to 1SMS the 1st notification telephone number refer to chart 4 as recorded in the SIM card memory and a triggered alarm SMS notification to the telephone numbers designated at 1SMS 6SMS figs 4 6 Additionally the telephone number designated at 1SMS receives status and setting messages Status messages are dispatched at the time intervals programmed The time schedule reference point is initiated and established upon receipt of the setting SMS The status message contains the remaining SIM card account balance When an alarm event is triggered the Motion Detector transmits an SMS message and places an outgoing call to the ist primary telephone number and then subsequently calls the additional telephone numbers The Motion Detector will terminate the outgoing call and proceed to call the next telephone in the following case When the subscriber is in network but does not pick up after 30 seconds When the subscriber is in network but the line is busy after 5 seconds When the subscriber is in out of network after 10 seconds Dialing out will cease when one of the dialed s
12. d 3 Not later than 5 seconds after the initial beep press the button located on the Motion Detector circuit board keeping it depressed until the start of numerous beeps The erasure of the telephone book has commenced and is accompanied by the sound of numerous short beeps 4 Wait for the short beeps to cease and after 3 seconds the Motion Detector will re boot After erasure the SIM card can now be utilized in future programming and set up 2 5 Initial programming set up After the Motion Detector powers up for the first time cells with default values will be created in the SIM card telephone book Later you will be able to edit these values Execute the following in consecutive order 1 Prepare using the telephone you intend to designate as the primary number for notifications an SMS message to be sent to the SIM card contained in the Motion Detector 2 The text message must contain the Motion Detector designated name the symbol amp and your E mail For example home amp abc yourprovider com Home as the name of the Motion Detector is selected arbitrarily at your discretion 3 Access and enter the programming mode on the device see 2 3 4 Within the span of 3 minutes after accessing and entering the programming mode of the Motion Detector send the previously prepared SMS text message to the SIM card in the Motion Detector The telephone number will register at cell 1 1sms the Motion Detector designated name at cell 27
13. e The recommended installation height is approximately 2 to 2 5m or 6 to 8 ft At an installation height of 2m 6 5 ft the detection range is approximately 10 m 32 ft at a field of view of 87 degrees see fig 9 10m 33 5m 16 0 0 5m 16 10m 33 N 2m 7 3m 10 5m 16 10m 33 Fig 9 Diagram of the detection zone Do not install the Motion Detector near heat sources fireplaces stoves air conditioners heating radiators or in any location exposed to strong air flow or direct sunlight see fig 10 16 EXPRESS N S v t v heating i radiator Fig 10 Examples of improper installation The wall on which the Motion Detector is mounted should not be subject to vibration The Motion Detector should be kept at a distance from high voltage electrical wiring The presence of objects in the protected zone such as furniture screens plants etc might create blind spots possibly hindering the detection of human presence Follow these steps in order to install the Motion Detector 1 Select a location on the wall for installation taking into account the special cut out opening on the back of the Motion Detector main body base special cut out opening see fig 2 2 Install the screw 3 Attach the Motion Detector In order to evaluate the sensitivity of the Motion Detector in the detection zone set the parameter value at Opov 2 see chart 4 cell 18 Move about thru out the zon
14. e in order to evaluate the sensitivity of the Motion Detector Warning After evaluating the detection zone reset the parameter values at Opov to 0 or 1 2 11 Arming and disarming the Motion Detector device Armed disarmed alarm modes of the protected zone are controlled via the keychain Remote Controls programmed and registered with the Motion Detector To arm alarm mode briefly 1 2 sec press the A button on the keychain Remote Control While waiting for the Motion Detector to respond the keychain Remote Control light diode glows yellow Wait for the keychain Remote Control light diode to blink red The armed mode delay will be activated 40 second default setting see chart 4 cell 19 At the conclusion of the delay the Motion Detector will enter armed mode To disarm alarm mode press the B button on the Keychain Remote Control While waiting for the Motion Detector to respond the keychain Remote Control light diode glows yellow When the Motion Detector enters disarmed mode the keychain Remote Control light diode blinks green lf the cell PostSnt see chart 4 cell 16 is set to parameter value 2 the primary telephone number will receive an SMS containing the text Armed Home or Disarmed Home see fig 2 3 In the event the keychain Remote Control button is pressed more than once prior to the Armed or Disarmed SMS mode status being sent the SMS notification will contain and reflect the most
15. interrupted operating span resulting in fewer SMS messages and photographs being sent GSM 900 1800 1900 5 Z EXPRESS 1 3 Motion Detector package contents Motion Detector package contents in accordance with chart 2 Chart 2 Motion Detector contents GSM Motion Detector EXPRESS E3 AA Batteries LR6 1 5v O ee Keychain RC Remote Control BN 3S 1 4 Motion Detector design structure Structurally the Motion Detector consists of a main body base a front cover a rear lid removable detector circuit board and GSM module circuit board refer to fig 1 2 The detector and GSM module circuit boards attach to the main body base with stand off tabs A SIM card holder is installed on the GSM module circuit board and a battery holder GSM light diode signal indicator a built in announcer and button refer to fig 2 are installed on the detector circuit board Batteries are installed in the device and are insulated from the contacts by means of a plastic protective insulating insert refer to fig 2 The Motion Detector is designed for use on a wall and can be mounted using a screw that utilizes a special cutout found on the back of the Motion Detector main body base refer to fig 2 main body base camera lens front cover rear lid Fig 1 Overview of the Motion Detector structural design EXPRESS special cutout for mounting screw GSM light diode SIM card holder signal indicato
16. l continue to flash At the completion of the registration cycle the GSM light dlode will flash once every five seconds and will emit 3 audible tones This confirms that the Motion Detector has entered the programming mode If the GSM light diode continues flashing rapidly it might mean that the SIM card is improperly installed is missing access blocked by a PIN code or the GSM network is unavallable EXPRESS For a span of 3 minutes the Motion Detector stands by to receive SMS notification s containing setting changes inquiries from Remote Controls and incoming calls At the conclusion of which the Motion Detector will return to Disarmed mode and will transmit an SMS notification containing the settings to the primary telephone number In order to shorten conclude and exit the programming mode press the button on the Motion Detector circuit board for 1 2 seconds prior to the 3 minute conclusion beep or press the F button on the Remote Control 2 4 Erasing the phonebook and SMS messages In the event that the SIM card was previously used in a Motion Detector it is mandatory to erase all previous SMS messages and phone book entries To accomplish this execute the following in consecutive order 1 Confirm that the SIM card is installed as shown in fig 7 2 Remove the protective insulating insert from the battery contacts as shown in fig 7 or install batteries observing correct polarity in the event they were previously remove
17. n accordance with chart 4 For example dial 1 and then Cell 1 will open up This is where the primary notification telephone number can be registered Warning Certain telephones do not support this function This method cannot be employed to register Remote Controls 2 7 Adding a telephone number for notification messages There are two methods to add a telephone number notification messages First method 1 Access the Motion Detector programming mode see 2 3 For a span of 3 minutes the Motion Detector will stand by to receive incoming calls 2 Place a call from the telephone number to be added to the Motion Detector 3 Wait for the Motion Detector to drop the call 4 Wait for the Motion Detector to emit a tone The telephone number will be saved in an available cell at 2sms 6sms 5 If itis necessary to add additional telephone numbers repeat 2 4 In total not exceeding 5 telephone numbers 6 In order to shorten conclude and exit the programming mode press the button on the Motion Detector circuit board for 1 2 seconds prior to the 3 minute conclusion beep or press the F button on the Remote Control 7 The primary telephone number for notification messages 1sms will receive an SMS containing the changed settings Second method 1 Access the Motion Detector programming mode 2 Send a previously prepared SMS message to the Motion Detector telephone number containing the f
18. ndroid and iOS applications An SMS message formatted by the Configurator will sent to the Motion Detector SIM card Second method 1 Remove the batteries from the Motion Detector 2 Create an SMS message using parameter values in accordance with chart 4 For example in order to change Type of Alarm Notification an SMS message should be sent to the Motion Detector containing the text 18 0 18 being the cell and O the parameter value In order to change multiple parameter values it is necessary to separate the parameter values using a comma For example 16 1 18 0 26 2121 etc 3 Install the batteries observing correct polarity 14 EXPRESS 4 Wait for the SIM card to register on the network During the registration process the GSM light diode will continue to flash At the completion of the registration cycle the GSM light diode will flash once every five seconds and will emit 3 tones 5 Send the previously prepared SMS message to the Motion Detector telephone number 6 Wait to receive an SMS message confirming the changes Third method It is possible to change the parameter values utilizing a GSM mobile telephone Install the Motion Detector SIM card into the GSM mobile telephone In order to access the necessary parameter value dial the cell parameter value in question on the telephone in accordance with chart 4 and then press The telephone will enter the cell and the parameter value can be changed i
19. nochrome 2 Color image Value digit 3 Image compression quality 1 low 4 best Value digit 4 0 Single photo only Delayed second photo 1 6sec 9 30sec 3 sec intervals Motion Detector Up to 20 characters of text signature on using the Latin or Cyrillic photograph alphabet Typical format using Latin characters abc provider com Gateway address of the Up to 30 characters of text mobile operator using the Latin alphabet 11 EXPRESS Settings User name for the mobile Up to 30 characters of text stored In operator using the Latin alphabet Settings User password for mobile Up to 30 characters of text stored in operator using the Latin alphabet 2 3 Entering the programming mode In order to access the Motion Detector programming mode execute these following steps in consecutive order 1 Install the SIM card as shown in fig 7 SIM card holder protective insulating insert fig 7 SIM card installation 2 Remove the protective insulating insert from the battery contacts as shown in fig 7 If the protective insulating insert was previously removed then remove the battery wait 2 minutes then re insert the batteries making sure to observe proper polarity 3 Wait until you hear a long single tone The GSM light diode will glow for 3 seconds and will then proceed to flash rapidly 4 Wait for the SIM card to register on the network During the registration process the GSM light diode wil
20. number etc In order to erase a few telephone numbers at once separate the designated parameter values with a comma For example 2 000 3 000 4 000 5 000 6 000 this erases all the additional notification telephone numbers 3 The Motion Detector will beep once for each telephone number deleted 2 9 Erasing a keychain Remote Control In order erase a previously registered keychain Remote Control perform the following step by step operation 1 Access the Motion Detector programming mode see 2 3 2 Send an SMS to the Motion Detector telephone number containing the following text text is entered without the angle brackets 8 000000000 erasing remote control 1 9 000000000 erasing remote control 2 etc In order to erase a few Remote Controls at once separate the designated parameter values with a comma For example 8 000000000 9 000000000 10 000000000 11 000000000 12 000000000 13 000000000 this erases all the registered keychain Remote Controls 3 The Motion Detector will beep once for each keychain Remote Control deleted 2 10 Installing the Motion Detector Install the Motion Detector in the zone to be protected at a location where it will be protected from exposure to atmospheric precipitation physical damage and access by any unauthorized personnel The Motion Detector should be installed in a manner that takes into account the likely path of a violator crossing into and through the axis of the protected zon
21. ollowing text text is entered without the angle brackets 2 1TO0xxxwoxx 3 1yyyyyyyyyy 6 1zzzzzzzzzz 2 6 being the cell position see chart 4 1 XXXXXXXXKX t 1zzzzzzzzzz Notification telephone numbers The numbers will be recorded in available cells 2sms 6sms For example 2 17182222222 to add one additional notification number 2 17182222222 3 17180000000 to add two additional notification numbers 2 17182222222 3 17180000000 4 17181 111111 5 17183333333 6 17184444444 to add five additional notification numbers 3 The Motion Detector will beep once for each telephone number added 4 In order to shorten conclude and exit the programming mode press the button on the Motion Detector circuit board for 1 2 seconds prior to the 3 minute conclusion beep or press the F button on the Remote Control 5 The primary telephone number for notification messages isms will receive an SMS containing the changed settings 15 EXPRESS 2 8 Erasing notification message telephone numbers in order erase a telephone number from the notification list perform the following operation 1 Access the Motion Detector programming mode see 2 3 2 Send an SMS to the Motion Detector telephone number containing the following text text is entered without the angle brackets 2 000 to erase the second notification telephone number 3 000 to erase the third notification telephone
22. r N GSM module circuit board ee EE _ button fe detector protective circuit board insulating insert _ power source batteries battery holder _ Fig 2 Motion Detector structural design with rear lid removed 1 5 Keychain remote control structural design The keychain Remote Control structural design consists of a base a cover button unit 3 button and a light diode refer to fig 3 Inside the keychain Remote Control is a CR2032 Lithium 3v battery In order to replace the power source it is necessary to remove the screw lift the cover remove the depleted battery and then observing polarity install a new battery Replace the cover and tighten it using the screw light diode button body buttons A B amp F Fig 3 Overview of the keychain Remote Control structural design 1 6 Device set up and operation Basic Motion Detector functions The Motion Detector executes the following functions detects movement within a 10m protected zone places calls and transmits triggered SMS alarm messages to the telephone numbers registered on the Motion Detector SIM card photographs the protected zone when triggered by penetration transmits a photograph via GPRS to the e mail address registered on the Motion Detector SIM card transmits an SMS message confirming armed disarmed modes 7 EXPRESS requests remaining Motion Detec
23. recent occurrence If a violation occurs during the Armed mode the protected zone is penetrated the Motion Detector will transmit an SMS notification containing the text Alarm Home see fig 4 and or start placing calls to the designated telephone numbers depending on the notification parameter value selected see chart 4 cell 18 17 EXPRESS If a notification delay is designated see chart 4 cell 20 then the Motion Detector will wait out the designated delay and then start the notifications lf the notification delay is set at 0 20 seconds the Motion Detector will without any further delay start the notifications due to the notification delay compensating for the time required for the GSM module to power up and the SIM card to register with the mobile network The time needed for the GSM module to power up and for the SIM card to register with the mobile network is approximately 10 30 seconds After the Motion Detector concludes transmitting the notifications it e mails a photograph via GPRS and then stands by for 30 seconds to receive an incoming call from registered telephone notification numbers at 1sms 6sms to be Disarmed Upon receipt of an incoming call the Motion Detector will drop the call and will send an SMS notification containing the text Disarmed via a call from 1718xxxxxxx Home if the PostSnt cell contains a 2 and will enter Disarmed mode It is also possible to enter disarmed
24. tor SIM card balance and transmits an SMS to the handheld mobile device auto reset to armed mode auto detection of telephone number for remaining Motion Detector SIM card balance and of GPRS settings disarm alarm mode via a telephone call after triggered alarm Footnote for mobile providers T Mobile AT amp T Orange amp Vodafone Basic Keychain Remote Control functions The Keychain Remote Control executes the following functions arms the Motion Detector using button A disarms the Motion Detector using button B requests remaining Motion Detector SIM card balance using button F quick exit out of programming mode using button F see 2 3 Keychain Remote Control and Motion Detector indicators The Motion detector was designed with light and sound indicators The GSM light diode on the detector circuit board indicates the state of the GSM network The light diode on the Keychain Remote Control indicates armed disarmed mode communication with the Motion Detector and balance inquiry Indicator descriptions are detailed in Chart 3 Chart 3 Motion Detector and Keychain Remote Control Indicators 7 RC Indicator MD Sound Indicator GSM light diode Dani network search e flashing 20 40 sec Successful GSM 3 beeps 1 time in 5 sec network registration mama e memo ew o me send SMS RC successfully alternate red green 1 beep programmed flashes RC previously alternate red green 2
25. ubscribers responds to the call by picking up and or hanging up Next the Motion Detector will transmit an SMS Alarm text message to the telephone numbers located at 2SMS 6SMS Alarm armed by Remote Control 1 home fig 4 SMS Armed Alarm disarmed by Remote Control 1 home 7 Alarm disarmed by a call from 17180000000 home fig 5 SMS Disarmed 2 ALARM home fig 6 SMS ALARM home Motion Detector label name see 2 5 Photographs The protected zone is photographed not later than 1 second after penetration of the protected zone is detected After all tha SMS messages are transmitted the photograph is e mailed via GPRS In the event the default settings are changed see Chart 4 Cell 26 and Value 4 the protected zone can be photographed 2 times after penetration The second photograph is taken with a delay of 6 to 30 seconds after the initial photograph depending on the selected value parameter setting 2 SET UP PROCEDURE 2 1 Preparing the device for operation Unpack and visually inspect the Motion Detector to make sure nothing is damaged or missing Prior to proceeding with set up de activate the PIN code feature on the Motion Detector SIM card with the assistance of a GSM mobile telephone see user manual for the mobile telephone Confirm that the SIM card has a credit balance and connects to GPRS Data In the event the SIM card was previously used erase reformat the SIM
Download Pdf Manuals
Related Search