AiM User manual EVO4 and SoloDL connection kit for Kawasaki
Contents
1. 5 pins Binder 712 male connector male connector O speed beacon m Si p OK QO IILI OOO o CH1 CH2 CH3 CH4 CH5 O 4 an User Guide Configuring with Race Studio 2 Before connecting SoloDL EVO4 to the ECU set it up using Race Studio 2 software The parameters to select in the logger configuration are e ECU Manufacturer Kawasaki e ECU model KIT RACING 5 Kawasaki KIT RACING protocol Channels received by SoloDL EVO4 with Kawasaki KIT RACING protocol are ECU_1 ECU_2 ECU_3 ECU_4 ECU_5 ECU_6 ECU_7 ECU_8 ECU_9 ECU_10 ECU_11 ECU_12 ECU_13 ECU_14 ECU_15 NOME CANALE ZX_RPM ZX_SPEED_F ZX_SPEED_R ZX_TPS ZX_ECT ZX_IAT ZX_GEAR ZX_CLUTCH ZX_POW_MODE ZX_TC_MODE ZX_SHIFTER ZX_PIT_ROAD ZX_DIAG_CODE_1 ZX_DIAG_CODE_2 ZX_DIAG_CODE_3 FUNZIONE RPM Front wheel speed Rear wheel speed Throttle position sensor Engine coolant temperature Intake air temperature Engaged gear Clutch switch Selected power mode Traction control mode Shifter Pit lane speed limiter Diagnostic code 1 Diagnostic code 2 Diagnostic code 3 ECU_16 ZX_V_BATT Battery supply ECU_17 ZX TC SELECT Selection of traction control level Technical note not all data channels outlined in the ECU template are validated for each manufacturer model or variant some of the outlined channels are model and year specific and therefore may not be applicable2. AiM User manual EVO4 and SoloDL connection kit for Kawasaki Ninja ZX 10R and ZX 10R Racing kit 2011 2015 Release 1 01 User Guide I 1 Supported models and years This user manual explains how to connect AiM SoloDL and EVO4 to your bike engine control unit ECU Supported models and years are e Kawasaki Ninja ZX 10R 2011 2015 e Kawasaki Ninja ZX 10R Racing kit 2011 2015 Warning AiM recommends not to remove the bike stock dash to avoid losing traction control and map selection management CTD User Guide 2 Connection kit for SoloDL and EVO4 AiM designed and developed connection kits for SoloDL and EVO4 Here below SoloDL connection kit is shown part number V02569220 with the related constructive scheme 6 pins Sumitomo male connector pinout contact insertion view 2 3 Red Vbext O aa 6 ne 6 nc g O gt Z e h p H Oo Nero GND 7 pins Binder 712 male connector pinout solder termination view LLL User Guide EVO4 connection kit is shown here below part number V02563160 with the related constructive scheme 5 pins Binder 712 male connector pinout solder termination view 6 pins Sumitomo male connector pinout contact insertion view DOG ci Black GND White CAN Bue CAN CTD User Guide 3 Connecting SoloDL and EVO4 SoloDL can be installed on the bike steering while EVO4 can be installed under the
3. bike seat Position of the ECU connector to be used changes according to the bike model Kawasaki ZX10R connector is under the bike seat and is called diagnosis connector while Kawasaki ZX10R Racing kit connector is under the windscreen and is called CAN output 3 1 Connecting SoloDL To connect SoloDL to your Kawasaki ZX10R ECU use the diagnosis connector placed under the bike seat SoloDL connection cable is 140 cm long To connect SoloDL to your Kawasaki ZX10R Racing kit ECU use CAN OUTPUT connector placed under the bike windscreen CTD User Guide Connection between SoloDL and connection kit is shown here below larg ob 2 6 pins Sumitomo male connector HHN 4x0 35mm cable 3 2 Connecting EVO4 To connect EVO4 to your Kawasaki ZX10R ECU use diagnosis connector placed under the bike seat CTD User Guide To connect EVO4 to your Kawasaki ZX10R Racing ECU kit use CAN output connector placed under the bike windscreen To connect ECU connector under the windscreen to EVO4 installed under the bike seat use the CAN extension cable shown here on the right The cable is available in multiple lengths Part numbers are e 1m CAN extension cable V 02552700 e 1 5m CAN extension cable V02552710 Connection between EVO4 connection kit and CAN extension when needed is shown here below 5 pins Binder 712 5 pins Binder 712 male connector female connector 6 pins Sumitomo
Download Pdf Manuals
Related Search