PE-8201 – Wireless Roller Shutter Magnetic Contact User Manual
Contents
1. User Manual Installation Guide PE 8201 Wireless Roller Shutter Magnetic Contact User Manual PE 8201 is Mini wireless roller shutter magnetic contact with novelty and streamline design it included 3 parts wireless emitter metallic sensor and metallic magnet when the metallic sensor is separated from metallic magnet more than 4 cm it will cause short circuit and the wireless emitter alarm LED indication will flash and also send out wireless alarm signal to the control panel at the same time with higher sensitivity within 120m away from control panel via built in antenna wireless coding or entering the 9 digit address code with alarm control panel and it fits well the surroundings and can be decorative at residence Features Metallic Sensor 1 adopted special micro power low consumption CPU 2 adopted patented multi code Metallic Magnet 3 Code 28 digit ID 8 digit function code 36 digit date code iN LED Indication total working status report automatically loss alarm periodic report when roller shutter is not well closed Wireless working voltage is 3 0V 1pc x CR123A 3 0V Lithium Battery 5m tter current consumption lt 5uA static lt 15mA alarm wireless emitting frequency 433MHz 868MHz wireless emitting distance 120m in open area working temperature is 10 C 50 C 2 a a et OS O dimension is 80 32 25mm wireless emitter 74 20 12mm metallic magenet 105 37 10mm metallic senso2. on normal mode place 1pc 3 0V CR123A lithium battery and LED light will flash alarm control panel on wireless coding mode please refer to control panel user manual move the metallic magnet more than 4cm from metallic sensor it will cause short circuit and the wireless emitter alarm LED indication will flash and also send out wireless signal to the control panel at the same time if alarm control panel make the corresponding indicate sound it means match code successfully 2 alarm control panel on manual coding mode enter the 9 digit address code to match this will be a higher probability of coding success Change Battery Battery life is around 1 year should change the battery when the signal between detector and control panel becomes weak The detector also can send the low battery alarm indication to alarm control panel CR123A 3 0V Lithium Battery pay attention to the anode and cathode Battery Testing After replaced the new batteries the detector will be in testing mode via LED light flash indicate for each triggering and detector will auto enter the normal mode after 5 mins and the LED light indicate will be switched off battery energy for power saving function Maintenance After being long use detector may get dirty on surface use wet cloth or sponge to rub it Don t let the water inside unit so that avoid break the inside electronic accessory please re test after cleaning it Warning we are not responsible for the p
3. r ivory white color Installation install metallic magnet l install metallic sensor 1 mark the drill hole and drill holes at the bottom of roller shutter fix the metallic magnet on the roller shutter with screws 2 drill holes on the ground and parallelled to metallic magnet so that fix the metallic sensor on the ground 3 connect the two wires of metallic sensor to NC and COM terminal of wireless emitter l l o connect wireless emitter with 4 install wireless emitter on the wall inside of roller shutter l o metallic sensor via wired User Manual Installation Guide Installation Emitter Battery remove the wireless emitter cover you will see the inside PCB board take out the PCB board the mounting frame is under the PCB board hold the frame against the mounting surface and mark the 2 drilling points through the mounting holes so NS drill the holes and fix frame to the wall using the screws with countersink heads which had been packed in the package 5 the 9 digit address code is under mounting frame put the PCB board back to the frame after installed on the wall or other stable place 6 insert 1pc CR123A 3 0V Lithium Battery on the battery tray pay attention to the anode and cathode and then LED light will flash 3 times so that make sure the battery had been connected 7 close the wireless emitter cover Coding Method between detector and alarm control panel 1 detector
4. roblem caused by improper operation or change the product configuration it may lose the authority of product warranty 2
Download Pdf Manuals
Related Search