FLEXIDOME HD VR - Norbain SD Ltd
Contents
1. Wait until there is a free connection and call the transmitter again Bosch Security Systems Installation Manual AM18 Q0637 v1 0 2012 12 36 en Troubleshooting FLEXIDOME HD VR Malfunction Possible causes Solution No audio transmission to remote station Hardware fault Check that all connected audio units are operating correctly Faulty cable connections Check all cables plugs contacts and connections Incorrect configuration Check audio parameters on the Audio configuration and LIVEPAGE Functions pages The audio voice connection is already in use by another receiver Wait until the connection is free and then call the sender again The unit does not report an alarm Alarm source is not selected Select possible alarm sources on the Alarm sources configuration page No alarm response specified Specify the desired alarm response on the Alarm connections configuration page if necessary change the IP address The unit is not operational after a firmware upload Power failure during programming by firmware file Have the unit checked by Customer Service and replace if necessary Incorrect firmware file Enter the IP address of the unit followed by main htm in your Web browser and repeat the upload AM18 Q0637 v1 0 2012 12 Installation Manual Bosch Security Systems2. Audio in Audio out The unit has full duplex mono audio The two way communication can be used to connect a speaker or door Bosch Security Systems Installation Manual AM18 Q0637 v1 0 2012 12 24 en Installation FLEXIDOME HD VR intercom system The audio input signal is transmitted in sync with the video signal Refer to the cable tree table to identify the wire colors for connecting the audio input and output Audio in Line input level not suitable for direct microphone signal Audio out Line output level not suitable for direct speaker connection Wiring Shielded audio connection cable is advised 5 4 Mount the camera 1 Route the cable tree from the camera around the rear of the camera module and secure all cables 2 Attach the camera module securely using the three supplied screws AM18 Q0637 v1 0 2012 12 Installation Manual Bosch Security Systems FLEXIDOME HD VR Installation en 25 5 5 Controls 1 Reset button Restores the default IP address or restores a previous version of the firmware if uploading a new version fails With the power on use a small pointed object to press and hold the reset button for more than 10 seconds to restore the factory defaults 2 Menu button Use this button to start the field of view installation wizard 3 MicroSD card slot Insert a microSD card into the slot Service video output 2 5 mm jack provides a C
3. Read follow and retain for future reference all of the following safety instructions Follow all warnings on the unit and in the operating instructions before operating the unit 1 Clean only with a dry cloth Do not use liquid cleaners or aerosol cleaners Do not install unit near any heat sources such as radiators heaters stoves or other equipment that produce heat Avoid exposure to direct sunlight for long periods Never spill liquid of any kind on the unit Take precautions to protect the unit from power and lightning surges Adjust only those controls specified in the operating instructions Operate the unit only from the type of power source indicated on the label Unless qualified do not attempt to service a damaged unit yourself Refer all servicing to qualified service personnel Install in accordance with the manufacturer s instructions in accordance with applicable local codes Use only attachments accessories specified by the manufacturer Equipment change or modification could void the user s guarantee or authorization agreement Connect the yellow green earth wire of the camera to the system earth of the installation to ensure correct safety and EMC RFI protection AM18 Q0637 v1 0 2012 12 Installation Manual Bosch Security Systems FLEXIDOME HD VR Safety en 7 1 3 1 4 Connection in applications Grounding The yellow green safety power ground wire from the camera must be connected
4. 600 mA 12 VDC 500 mA 24 VAC 175 mA PoE 48 VDC Minimum illumination Lens 3 9 mm F1 2 0 25 Ix Color 30 IRE 0 08 Ix Mono 30 IRE Minimum illumination Lens 10 23 mm F1 6 0 45 Ix Color 30 IRE 0 15 Ix Mono 30 IRE Day Night Color Mono IR contrast Auto Dynamic range gt 90 dB typical Noise reduction Intelligent Dynamic Noise Reduction iDNR with separate temporal and spatial adjustments BLC Off Auto IntelligentAE White Balance ATW AWB hold and manual 2500 to 10000k Indoor and Outdoor ATW Shutter Automatic Electronic Shutter AES Fixed 1 30 1 25 to 1 150000 selectable Default shutter Contrast On Off enhancement Sharpness Sharpness enhancement level selectable Privacy Masking Four independent areas fully programmable Video Analysis Motion IVA Bosch Security Systems Installation Manual AM18 Q0637 v1 0 2012 12 40 en Technical Data FLEXIDOME HD VR Lens type 3 to 9mm or 10 to 23 mm varifocal SR Super Resolution Auto Varifocal AVF adjustment Automatic iris control Controls Via web browser or Configuration Manager User modes 6 pre defined customizable user modes LAN interface STP Ethernet 10 100 Base T auto sensing half full duplex RJ45 Video encoding H 264 ISO IEC 14496 10 M JPEG protocols Stream max 1080p25 30 Group of pictures IP IBP IBBP Network
5. FLEXIDOME HD VR Troubleshooting en 37 Malfunction Possible causes Solution Placeholder with a red cross instead of the ActiveX components JVM not installed on your computer or not activated Install JVM on your computer Web browser contains empty fields Active proxy server in network Create a rule in the local computer s proxy settings to exclude local IP addresses The POWER LED is red Firmware upload failed Repeat firmware upload 8 3 Customer service If a fault cannot be resolved please contact your supplier or system integrator or go directly to Bosch Security Systems Customer Service The version numbers of the internal firmware can be viewed on a special page Please note this information before contacting Customer Service 1 Inthe address bar of your browser after the unit IP address enter version for example 192 168 0 1 version 2 Write down the information or print out the page Bosch Security Systems Installation Manual AM18 Q0637 v1 0 2012 12 38 en Maintenance FLEXIDOME HD VR 9 9 1 9 2 Maintenance Testing the network connection The ping command can be used to check the connection between two IP addresses This allows testing whether a device is active in the network 1 Open the DOS command prompt 2 Type ping followed by the IP address of the device If the device is found the response
6. FTP Telnet ARP DHCP SNTP SNMP V1 MIB II 802 1x SMTP iSCSI UPnP SSDP Encryption TLS 1 0 SSL AES optional Analog video BNC connector CVBS PAL NTSC 1 Vpp 75 Ohm Analog video service only 2 5 mm jack CVBS PAL NTSC 1 Vpp 75 Ohm non protected Alarm input Non isolated closing contact TTL logic 5V nominal 40 VDC max DC coupled with 22 kOhm pull up to 3 3 VDC Relay output Maximum voltage 30 VAC or 40 VDC Maximum 0 5 A continuous 10 VA Audio input 1 Vrms impedance 12 kOhm Audio output 1 Vrms impedance 1 5 kOhm AM18 Q0637 v1 0 2012 12 Installation Manual Bosch Security Systems FLEXIDOME HD VR Technical Data en 45 Audio standards AAC G 711 8kHz sampling rate L16 16kHz sampling rate Audio signal to noise ratio gt 50 dB Memory card slot Supports SDHC and SDXC microSD cards Weight 0 84 kg 1 85 Ib Environment IP 66 NEMA Type 4X Impact protection IK10 Operating temperature 30 C to 50 C 22 F to 122 F 10 1 1 Dimensions 158 6 22 95 3 7 141 5 55 Bosch Security Systems Installation Manual AM18 Q0637 v1 0 2012 12 46 en Technical Data FLEXIDOME HD VR AM18 Q0637 v1 0 2012 12 Installation Manual Bosch Security Systems Bosch Security Systems www boschse
7. IVA PoE 48 VDC Minimum illumination Lens 3 9 mm F1 2 0 22 Ix Color 30 IRE 0 05 Ix Mono 30 IRE Minimum illumination Lens 10 23 mm F1 6 0 4 Ix Color 30 IRE 0 1 Ix Mono 30 IRE Day Night Color Mono IR contrast Auto Dynamic range Digital WDR 76 dB Noise reduction Intelligent Dynamic Noise Reduction iDNR with separate temporal and spatial adjustments BLC Off Auto White Balance ATW AWB hold and manual 2500 to 10000k Indoor and Outdoor ATW Shutter Automatic Electronic Shutter AES Fixed 1 30 1 25 to 1 150000 selectable Default shutter Contrast On Off enhancement Sharpness Sharpness enhancement level selectable Bosch Security Systems Installation Manual AM18 Q0637 v1 0 2012 12 42 en Technical Data FLEXIDOME HD VR Privacy Masking Four independent areas fully programmable Video Analysis Motion IVA versions Lens type 3 to 9mm or 10 to 23 mm varifocal SR Super Resolution Auto Varifocal AVF adjustment Automatic iris control Controls Via web browser or Configuration Manager User modes 6 pre defined customizable user modes LAN interface STP Ethernet 10 100 Base T auto sensing half full duplex RJ45 Video encoding H 264 ISO IEC 14496 10 M JPEG protocols Stream max 1080p25 30 Group of pictures IP IBP IBBP Network protocols IPv4 IPv6 UDP TCP HTTP HTTP
8. via the SSL encryption protocol With an additional license the user data itself can be encrypted AM18 Q0637 v1 0 2012 12 Installation Manual Bosch Security Systems FLEXIDOME HD VR System Information en 15 3 1 12 Recording The camera can be used with an iSCSI server connected via the network to store long term recordings and with a local microSD card for shorter storage times and temporary recordings 3 1 13 Configuration The camera can be configured using a browser on the local network Intranet or from the Internet Similarly firmware updates and rapid loading of device configurations are also possible Configuration settings can be stored as files ona computer and copied from one camera to another Bosch Security Systems Installation Manual AM18 Q0637 v1 0 2012 12 16 enl System Information FLEXIDOME HD VR 3 2 Operation with external systems The camera can be used with a variety of Bosch systems Bosch Video Management System Bosch Video Client Bosch Recording Station When connected to any of these systems many of the camera configuration parameters are controlled by the system and not by the settings made via a web browser Bosch Video Management System The Bosch Video Management System is a unique enterprise IP video surveillance solution that provides seamless management of digital video audio and data across any IP network It is designed to work with Bosch CCTV products
9. 37 v1 0 2012 12 14 en System Information FLEXIDOME HD VR 3 1 5 3 1 6 3 1 7 3 1 8 3 1 9 3 1 10 3 1 11 Audio Two way duplex audio is available in the unit for live voice communications or audio recording Alarm I O The alarm input can be used to control the functionality of the unit An alarm output can control external devices Tamper detection and motion detection The camera offers a wide range of configuration options for alarm signaling in the event of tampering with the camera A Motion algorithm for detecting movement in the video image is included Video encoding The camera uses the H 264 compression standards Thanks to efficient encoding the data rate remains low even with high image quality and can also be adapted to local conditions within wide limits Multicast In suitably configured networks the multicast function enables simultaneous real time transmission to multiple receivers The prerequisite for this is that the UDP and IGMP V2 V3 protocols are implemented on the network Power over Ethernet Power for the camera can be supplied via a Power over Ethernet compliant network cable connection With this configuration only a single cable connection is required to view power and control the camera Encryption The unit offers a variety of options for protection against unauthorized reading Web browser connections can be protected using HTTPS Protect the control channels
10. 637 v1 0 2012 12 Installation Manual Bosch Security Systems FLEXIDOME HD VR Safety en 11 1 9 Copyrights The firmware uses the fonts Adobe Helvetica Bold R Normal 24 240 75 75 P 138 ISO10646 1 and Adobe Helvetica Bold R Normal 12 120 75 75 P 70 ISO10646 1 under the following copyright Copyright 1984 1989 1994 Adobe Systems Incorporated Copyright 1988 1994 Digital Equipment Corporation Permission to use copy modify distribute and sell this software and its documentation for any purpose and without fee is hereby granted provided that the above copyright notices appear in all copies and that both those copyright notices and this permission notice appear in supporting documentation and that the names of Adobe Systems and Digital Equipment Corporation not be used in advertising or publicity pertaining to distribution of the software without specific written prior permission This software is based in part on the work of the Independent JPEG Group Bosch Security Systems Installation Manual AM18 Q0637 v1 0 2012 12 12 en Introduction FLEXIDOME HD VR 2 Introduction 2 1 Features The FLEXIDOME HD Vandal Resistant VR IP Day Night camera is a high performance surveillance color camera The analog video output of the camera can be used simultaneously with an IP stream to allow operation in hybrid mode The IP video stream uses H 264 compression technology to give clear images while reduci
11. FLEXIDOME HD VR NIN 733 NIN 832 NIN 932 BOSCH FLEXIDOME HD VR Table of Contents en 3 Table of Contents 1 Safety 5 1 1 Safety precautions 5 1 2 Important safety instructions 6 1 3 Connection in applications 7 1 4 Type label 7 1 5 FCC amp ICES compliance 8 1 6 MicroSD cards 9 1 7 UL certification 9 1 8 Bosch notices 10 1 9 Copyrights 11 2 Introduction 12 2 1 Features 12 3 System Information 13 3 1 Network video server 13 3 1 1 Progressive scan 13 3 1 2 True Day Night function 13 3 1 3 Multiple streams 13 3 1 4 ONVIF Open Network Video Interface Forum 13 3 1 5 Audio 14 3 1 6 Alarm UO 14 3 1 7 Tamper detection and motion detection 14 3 1 8 Video encoding 14 3 1 9 Multicast 14 3 1 10 Power over Ethernet 14 3 1 11 Encryption 14 3 1 12 Recording 15 3 1 13 Configuration 15 3 2 Operation with external systems 16 4 Planning 17 4 1 Unpacking 17 4 2 System requirements 17 Bosch Security Systems Installation Manual AM18 Q0637 v1 0 2012 12 4 en Table of Contents FLEXIDOME HD VR 5 Installation 18 5 1 Parts 18 5 2 Mounting the unit 19 5 2 1 Surface mounting 19 5 2 2 Flush mount 20 5 3 Connections 21 5 3 1 Make the connections 21 5 4 Mount the camera 24 5 5 Controls 25 5 6 Camera positioning and field of view 26 5 6 1 Pan 27 5 6 2 Tilt 27 5 6 3 Twist 28 5 7 Using the install wizard 29 5 7 1 Adjustment procedure 29 5 8 Closing the unit 30 6 Camera configura
12. S RTP IGMPV2 V3 ICMP RTSP FTP Telnet ARP DHCP SNTP SNMP V1 MIB II 802 1x SMTP iSCSI UPnP SSDP Encryption TLS 1 0 SSL AES optional Analog video BNC connector CVBS PAL NTSC 1 Vpp 75 Ohm Analog video service only 2 5 mm jack CVBS PAL NTSC 1 Vpp 75 Ohm non protected Alarm input Non isolated closing contact TTL logic 5V nominal 40 VDC max DC coupled with 22 kOhm pull up to 3 3 VDC Relay output Maximum voltage 30 VAC or 40 VDC Maximum 0 5 A continuous 10 VA Audio input 1 Vrms impedance 12 kOhm Audio output 1 Vrms impedance 1 5 kOhm Audio standards AAC G 711 8kHz sampling rate L16 16kHz sampling rate AM18 Q0637 v1 0 2012 12 Installation Manual Bosch Security Systems FLEXIDOME HD VR Technical Data en 43 Audio signal to noise ratio gt 50 dB Memory card slot Supports SDHC and SDXC microSD cards Weight 0 84 kg 1 85 Ib Environment IP 66 NEMA Type 4X Impact protection IK10 Operating 30 C to 50 C 22 F to 122 F temperature NIN 733 Imager 1 3 inch CMOS HD sensor Image resolution 1280 x 720 pixels Rated supply voltage 24 VAC 50 60 Hz 12 VDC Power over Ethernet 48 VDC nominal Current consumption 500 mA 600 mA IVA 12 VDC 450 mA 500 mA IVA 24 VAC 150 mA 175 mA IVA PoE 48 VDC Minimum illumination L
13. VBS signal for installation purposes only Bosch Security Systems Installation Manual AM18 Q0637 v1 0 2012 12 26 enllnstallation FLEXIDOME HD VR 5 6 Camera positioning and field of view The camera module position can be adjusted along three axes and several zoom positions can be selected To help position the camera and set the field of view 1 Connect a monitor to the 2 5 mm jack using the optional monitor cable S1460 which provides a CVBS signal for installation purposes only 2 Apply power to the camera After power up wait a little about 20 seconds 4 Press the Menu button This stops the IP video stream and Ce enables the service video analog output CAUTION Do not expose the sensors to direct sunlight AM18 Q0637 v1 0 2012 12 Installation Manual Bosch Security Systems FLEXIDOME HD VR Installation en 27 5 6 1 Pan For horizontal adjustment pan 1 Rotate the camera module 1 in the base Do not rotate more than 180 in either direction 2 Tighten the locking screw 2 with the supplied screwdriver bit 5 6 2 Tilt For vertical adjustment tilt 1 Loosen the two thumbwheels 1 2 Swing the camera module between the wings Do not rotate more than 90 3 Tighten the two thumbwheels 1 Bosch Security Systems Installation Manual AM18 Q0637 v1 0 2012 12 28 en Installation FLEXIDOME HD VR 5 6 3 Twist To obtain
14. a horizontal horizon for tilted ceilings or sidewall mounting twist the camera module to align the picture shown on the monitor AM18 Q0637 v1 0 2012 12 Installation Manual Bosch Security Systems FLEXIDOME HD VR Installation en 29 5 7 5 7 1 Using the install wizard The Menu button on the control panel is used to access the camera install wizard When there is a choice in the wizard the options are selected by either a short press less than 2 s ora long press more than 2 s of the button The wizard handles the following functions Lens identification Image orientation Zoom and focus adjustment conditions Auto focus Analog output Run the wizard to select orientation and field of view zoom Note The zoom and focus are adjusted again later with the dome bubble in place via the web browser This optimizes picture sharpness in both bright and low level lighting Adjustment procedure If you have set up the camera and pressed the Menu button as described in Section 5 6 Camera positioning and field of view page 26 then you see the following on the monitor screen Lens type Focus Indicator 0 SE CONTINUE 180 ROTATE Timeout 300 lt press short gt lt press long gt The lens type is identified and shown on the screen Theiris is opened to its maximum value Bosch Security Systems Installation Manual AM18 Q0637 v1 0 2012 12 30
15. ade close the unit AM18 Q0637 v1 0 2012 12 Installation Manual Bosch Security Systems FLEXIDOME HD VR Installation en 31 1 Disconnect the service cable from the video jack 2 Place the inner liner in position aligning its fin with the bracket on the base 3 Using the supplied screwdriver bit secure the dome bubble to the camera base by tightening the three screws Bosch Security Systems Installation Manual AM18 Q0637 v1 0 2012 12 32 en Camera configuration FLEXIDOME HD VR 6 6 1 6 2 Camera configuration The camera normally provides an optimal picture without the need for further adjustments Configuration of the camera is carried out via the network using a web browser User modes The camera has six user modes These modes contain optimized settings for a variety of applications Select the mode most suited to the camera s function via the web browser interface Day Night switching The camera is equipped with a motorized IR filter The mechanical IR filter is taken out of the optical path in low light applications The IR filter is controlled either via an alarm input or automatically based on the observed light levels If Auto switching mode is selected the camera automatically switches the filter depending on the observed light level The switching level is programmable Note When the auto mode is selected and the switching level is set to 15 certain borde
16. appears as Reply from followed by the number of bytes sent and the transmission time in milliseconds Otherwise the device cannot be accessed via the network This might be because The device is not properly connected to the network Check the cable connections in this case The device is not correctly integrated into the network Check the IP address subnet mask and gateway address Repairs CAUTION Never open the casing of the unit The unit does not contain any user serviceable parts Ensure that all maintenance or repair work is performed only by qualified personnel electrical engineering or network technology specialists In case of doubt contact your dealer s technical service center 9 2 1 Transfer and disposal The camera should only be passed on together with this installation guide The unit contains environmentally hazardous materials that must be disposed of according to law Defective or superfluous devices and parts should be disposed of professionally or taken to your local collection point for hazardous materials AM18 Q0637 v1 0 2012 12 Installation Manual Bosch Security Systems FLEXIDOME HD VR Technical Data en 39 10 10 1 NIN 932 Technical Data Specifications Imager 1 3 inch CMOS HD sensor Image resolution 1920 x 1080 pixels Rated supply voltage 24 VAC 50 60 Hz 12 VDC Power over Ethernet 48 VDC nominal Current consumption
17. as part of a total video surveillance management system Bosch Video Client The camera video server and the Bosch Video Client software combine to provide a high performance system solution The Bosch Video Client is a Windows application for viewing operating controlling and administering CCTV installations such as surveillance systems at remote locations Bosch Recording Station The camera is also designed for use with the Bosch Recording Station The Bosch Recording Station can record up to 64 video and audio streams The Bosch Recording Station supports various functions of the camera such as controlling relays remote control of peripheral devices and remote configuration It can use alarm inputs to trigger actions and when motion detection Motion is active can record the relevant cells making intelligent motion detection possible AM18 Q0637 v1 0 2012 12 Installation Manual Bosch Security Systems FLEXIDOME HD VR Planning en 17 4 Planning 4 1 Unpacking Unpack carefully and handle the equipment with care The packaging contains FLEXIDOME HD VR IP camera Torx screwdriver bit Camera mounting kit Mounting template RJ45 female to female network cable connector Optical disk Manuals Bosch Video Client Quick install instructions and safety instructions If equipment has been damaged during shipment repack it in the original packaging and notify the shipping agent or suppl
18. curity com Bosch Security Systems 2012
19. ed to the camera via the Ethernet cable compliant with the Power over Ethernet standard AM18 Q0637 v1 0 2012 12 Installation Manual Bosch Security Systems FLEXIDOME HD VR Installation en 23 CAUTION The RJ45 female to female network cable connector supplied is unshielded To comply with the EMC Alarm immunity standard EN 50130 4 or the EMC Railway immunity standard EN 50121 4 a shielded twisted pair STP connection cable and a shielded RJ45 female to female network cable connector not supplied should be used Analog video output Connect to the BNC connector to obtain an analog video signal This is a CVBS 1 Vpp PAL or NTSC signal depending on the selected camera base frequency Note If necessary use an isolation transformer to avoid ground loops Alarm Input Use the alarm input to connect external alarm devices such as door contacts or sensors A zero potential make or break contact can be used as the actuator use a bounce free contact system Refer to the cable tree table to identify the wire colors for connecting the alarm input Configurable as active low or active high Alarm output Use the alarm relay output for switching external devices such as lamps or sirens Refer to the cable tree table to identify the wire colors for connecting the alarm output Inthe menu system configure the relay output to operate as either normally open NO or normally closed NC
20. en Installation FLEXIDOME HD VR 1 To rotate the image 180 press and hold the Menu button until the image flips Briefly press the Menu button to set the start position for the automatic motorized focus adjustment You will hear the motorized automatic back focus process running The progress is shown on the monitor Briefly press the Menu button again and again to scroll through the preset zoom positions The selection loops back to the beginning when you reach the last one When you reach the desired zoom position use a long press of the Menu button to set the zoom position and to re focus If the camera is not correctly focussed press the Menu button for a longer time to restart the wizard If the camera is correctly focussed press the Menu button for a short time to change the analog output To change the analog output state press the Menu button for a short time Briefly press the Menu button again and again to select NTSC on PAL on or OFF default When the selection is made use a long press of the Menu button to save the results The zoom and focus position is stored Theiris is set to its original value The video service output is disabled The BNC video output is set to its selected state Note If the BNC video output is set to On the second IP stream is disabled 5 8 Closing the unit When the camera position is set and all adjustments have been m
21. ens 3 9 mm F1 2 0 017 Ix Color 30 IRE 0 0057 Ix Mono 30 IRE Minimum illumination Lens 10 23 mm F1 6 0 03 Ix Color 30 IRE 0 01 Ix Mono 30 IRE Day Night Color Mono IR contrast Auto Dynamic range 84 dB Noise reduction Intelligent Dynamic Noise Reduction IDNR with separate temporal and spatial adjustments BLC Off Auto IntelligentAE BLC White Balance ATW AWB hold and manual 2500 to 10000k Indoor and Outdoor ATW Shutter Automatic Electronic Shutter AES Fixed 1 30 1 25 to 1 150000 selectable Default shutter Contrast On Off enhancement Bosch Security Systems Installation Manual AM18 Q0637 v1 0 2012 12 44 en Technical Data FLEXIDOME HD VR Sharpness Sharpness enhancement level selectable Privacy Masking Four independent areas fully programmable Video Analysis Motion IVA versions Lens type 3 to 9 mm or 10 to 23 mm varifocal SR Super Resolution Auto Varifocal AVF adjustment Automatic iris control Controls Via web browser or Configuration Manager User modes 6 pre defined customizable user modes LAN interface STP Ethernet 10 100 Base T auto sensing half full duplex RJ45 Video encoding H 264 ISO IEC 14496 10 M JPEG protocols Stream max 720p60 Group of pictures IP IBP IBBP Network protocols IPv4 IPv6 UDP TCP HTTP HTTPS RTP IGMPV2 V3 ICMP RTSP
22. ensure that the watertight compartment is tightly closed and cables and conduits are properly sealed to prevent ingress of water Bosch Security Systems Installation Manual AM18 Q0637 v1 0 2012 12 22 en Installation FLEXIDOME HD VR Cable tree Use the following table to identify the wires in the cable tree Wire color AWG Signal Red 26 12 VDC 24 VAC Brown 26 GND DC 24 VAC Yellow Green 24 Earth Black Orange 28 Alarm Out A White Orange 28 Alarm Out B White Violet 28 Ground Alarm In Orange Violet 28 Alarm In 1 Violet 28 Alarm In 2 White 28 Audio In Shield 28 Ground Audio In Black 28 Audio Out Shield 28 Ground Audio Out For connections use wires of at least the same thickness Power connection 1 2 Use a class 2 power supply 24 VAC or 12 VDC Connect the power wires red brown to the power supply Isolate unused power wires individually Connect the earth wire yellow green from the camera to the system earth of the installation to ensure correct EMC RFI and safety protection Network and PoE connection 1 Use a shielded twisted pair STP Category 5e cable maximum length 100 meters Use the RJ45 female to female network cable connector to connect the network cable of the system to the RJ45 connector of the camera Auto MDIX compliant automatically detects the cable connection type Power is suppli
23. ices Video loss Video loss is inherent to digital video recording therefore Bosch Security Systems cannot be held liable for any damage that results from missing video information To minimize the risk of lost digital information Bosch Security Systems recommends multiple redundant recording systems and a procedure to back up all analog and digital information Optical elements Optical elements are sensitive and should be protected at all times Do not allow objects to come into contact with glass surfaces and do not touch optical elements with your fingers Copyright This manual is the intellectual property of Bosch Security Systems and is protected by copyright All rights reserved Trademarks All hardware and software product names used in this document are likely to be registered trademarks and must be treated accordingly Note This manual has been compiled with great care and the information it contains has been thoroughly verified The text was complete and correct at the time of printing The ongoing development of the products may mean that the content of the user guide can change without notice Bosch Security Systems accepts no liability for damage resulting directly or indirectly from faults incompleteness or discrepancies between the user guide and the product described More information For more information please contact the nearest Bosch Security Systems location or visit www boschsecurity com AM18 Q0
24. ier 4 2 System requirements Computer with Windows XP Vista 7 operating system network access and Microsoft Internet Explorer web browser version 9 or Computer with network access and reception software for example Bosch Video Client or Bosch Video Management System Bosch Security Systems Installation Manual AM18 Q0637 v1 0 2012 12 18 en Installation FLEXIDOME HD VR 5 Installation CAUTION Installation should only be performed by qualified service personnel in accordance with the National Electrical Code or applicable local codes 5 1 Parts The camera housing unit consists of the following parts i DH Surface Mount Box some models only Camera module and mounting base Inner liner Dome cover Pe he AM18 Q0637 v1 0 2012 12 Installation Manual Bosch Security Systems FLEXIDOME HD VR Installation en 19 5 2 Mounting the unit 5 2 1 Surface mounting 9 5 mm 0 375 in men mg f Pa ii PCD 123 mm 4 84 in To mount the camera on the surface of a wall or ceiling 1 Use the surface mount box as a template to mark the holes indicated in the drawing The PCD is 123 mm 4 84 in 2 Drill three holes with a diameter of 8 mm 0 3 in Insert the supplied plugs into the holes 4 Attach the surface mount box securely using the three b supplied screws 5 Ifyou use the side connection of the SMB remove the cap covering the side entrance other
25. ize the risk of loss of digital information we recommend multiple redundant recording systems and a procedure to back up all digital information 1 7 UL certification Disclaimer Underwriter Laboratories Inc UL has not tested the performance or reliability of the security or signaling aspects of this product UL has only tested fire shock and or casualty hazards as outlined in UL s Standard s for Safety for Information Technology Equipment UL 60950 1 UL Certification does not cover the performance or reliability of the security or signaling aspects of this product UL MAKES NO REPRESENTATIONS WARRANTIES OR CERTIFICATIONS WHATSOEVER REGARDING THE PERFORMANCE OR RELIABILITY OF ANY SECURITY OR SIGNALING RELATED FUNCTIONS OF THIS PRODUCT Disposal Your Bosch product was developed and manufactured with high quality material and components that can be recycled and reused This symbol means that electronic and electrical appliances which have reached the Mumm end of their working life must be collected and disposed of separately from household waste material Separate collecting systems are usually in place for disused electronic and electrical products Please dispose of these units at an environmentally compatible recycling facility per European Directive 2002 96 EC Bosch Security Systems Installation Manual AM18 Q0637 v1 0 2012 12 10 en Safety FLEXIDOME HD VR 1 8 Bosch not
26. ng bandwidth and storage requirements It is also ONVIF compliant to improve compatibility during system integration The camera operates as a network video server and transmits video and control signals over data networks such as Ethernet LANs and the Internet The camera is easy to install and ready to use Features include Progressive scan CMOS HD sensor Aesthetic vandal resistant enclosure True Day Night performance with switchable IR filter High performance lenses for HD resolution and extra DoF Automatic motorized focus and zoom adjustment Multiple streams MicroSD card slot ONVIF conformant Two way audio and audio alarm Alarm input and alarm output to external devices Intelligent dynamic noise reduction Enhanced video motion detection Video transmission over IP networks Multicast function Integrated Ethernet interface 10 100 Base T Power over Ethernet PoE Password protection Integrated Web server for live viewing and configuration via a browser Firmware update through flash memory Hybrid video outputs AM18 Q0637 v1 0 2012 12 Installation Manual Bosch Security Systems FLEXIDOME HD VR System Information en 13 3 3 1 3 1 1 3 1 2 3 1 3 3 1 4 System Information Network video server The camera incorporates a network video server Its primary function is to encode video and control data for transmi
27. protocols IPv4 IPv6 UDP TCP HTTP HTTPS RTP IGMPV2 V3 ICMP RTSP FTP Telnet ARP DHCP SNTP SNMP V1 MIB II 802 1x SMTP iSCSI UPnP SSDP Encryption TLS 1 0 SSL AES optional Analog video BNC connector CVBS PAL NTSC 1 Vpp 75 Ohm Analog video service only 2 5 mm jack CVBS PAL NTSC 1 Vpp 75 Ohm non protected Alarm input Non isolated closing contact TTL logic 5V nominal 40 VDC max DC coupled with 22 kOhm pull up to 3 3 VDC Relay output Maximum voltage 30 VAC or 40 VDC Maximum 0 5 A continuous 10 VA Audio input 1 Vrms impedance 12 kOhm Audio output 1 Vrms impedance 1 5 kOhm Audio standards AAC G 711 8kHz sampling rate L16 16kHz sampling rate Audio signal to noise ratio gt 50 dB AM18 Q0637 v1 0 2012 12 Installation Manual Bosch Security Systems FLEXIDOME HD VR Technical Data en 41 Memory card slot Supports SDHC and SDXC microSD cards Weight 0 84 kg 1 85 Ib Environment IP 66 NEMA Type 4X Impact protection IK10 Operating 30 C to 50 C 22 F to 122 F temperature NIN 832 Imager 1 2 7 inch CMOS HD sensor Image resolution 1920 x 1080 pixels Rated supply voltage 24 VAC 50 60 Hz 12 VDC Power over Ethernet 48 VDC nominal Current consumption 500 mA 600 mA IVA 12 VDC 450 mA 500 mA IVA 24 VAC 150 mA 175 mA
28. rline scene lighting conditions can cause the camera to switch back and forth between day and night modes Set a different switching level to avoid this AM18 Q0637 v1 0 2012 12 Installation Manual Bosch Security Systems FLEXIDOME HD VR Browser connection en 33 7 7 1 Browser connection A computer with Microsoft Internet Explorer can be used to receive live images from the camera control the camera and replay stored sequences The camera is configured over the network using the browser The configuration options using the menu system of the camera itself are limited to setting up the lens and network Note The camera can also be configured using the supplied Bosch Video Client or the Bosch Video Management System Protected network If a RADIUS server is used for network access control 802 1x authentication the camera must be configured first To configure the camera for a Radius network connect it directly to a PC via a crossed network cable and configure the two parameters Identity and Password Only after these have been configured can communication with the camera via the network occur Bosch Security Systems Installation Manual AM18 Q0637 v1 0 2012 12 34 en Troubleshooting FLEXIDOME HD VR 8 Troubleshooting 8 1 Function test The camera offers a variety of configuration options Therefore check that it works properly after installation and configuration This is the only way
29. ssion over an IP network With its H 264 encoding it is ideally suited for IP communication and for remote access to digital video recorders and IP systems The use of existing networks means that integration with CCTV systems or local networks can be achieved quickly and easily Video images from a single camera can be simultaneously received on several receivers Progressive scan The camera captures and processes progressively scanned images When there is fast motion in a scene progressively scanned images are generally sharper than interlaced images True Day Night function In night mode the camera enhances low light viewing by switching the IR infrared filter out of the optical path and providing a monochrome image The camera can switch from color to monochrome mode automatically by sensing the illumination level manually via the alarm input or remotely viaa web browser Multiple streams Multiple streams enable the camera to deliver several H 264 streams together with an M JPEG stream These streams facilitate bandwidth efficient viewing and recording options as well as integration with third party video management systems ONVIF Open Network Video Interface Forum The camera complies to the ONVIF standard which means that it is easier to install and integrate into larger systems The ONVIF standard is a global standard for the interface of network video products Bosch Security Systems Installation Manual AM18 Q06
30. tion 32 6 1 User modes 32 6 2 Day Night switching 32 7 Browser connection 33 7 1 Protected network 33 8 Troubleshooting 34 8 1 Function test 34 8 2 Resolving problems 35 8 3 Customer service 37 9 Maintenance 38 9 1 Testing the network connection 38 9 2 Repairs 38 9 2 1 Transfer and disposal 38 10 Technical Data 39 10 1 Specifications 39 10 1 1 Dimensions 45 AM18 Q0637 v1 0 2012 12 Installation Manual Bosch Security Systems FLEXIDOME HD VR Safety en 5 1 1 1 Safety Safety precautions DANGER High risk This symbol indicates an imminently hazardous situation such as Dangerous Voltage inside the product If not avoided this will result in an electrical shock serious bodily injury or death WARNING Medium risk Indicates a potentially hazardous situation If not avoided this could result in minor or moderate bodily injury CAUTION Low risk Indicates a potentially hazardous situation If not avoided this could result in property damage or risk of damage to the unit CAUTION The Low Voltage power supply unit must comply with EN UL 60950 The power supply must be a SELV LPS unit or a SELV Class 2 unit Safety Extra Low Voltage Limited Power Source GP Bb Be D CAUTION The camera must be connected to earth Bosch Security Systems Installation Manual AM18 Q0637 v1 0 2012 12 6 en Safety FLEXIDOME HD VR 1 2 Important safety instructions
31. to ensure that the camera will function as intended in the event of an alarm Your check should include the following functions Can you connect to the camera remotely Does the camera transmit all the data required Does the camera respond as desired to alarm events Is it possible to control peripheral devices if necessary AM18 Q0637 v1 0 2012 12 Installation Manual Bosch Security Systems FLEXIDOME HD VR Troubleshooting en 35 8 2 Resolving problems The following table is intended to help identify the causes of malfunctions and correct them where possible Malfunction Possible causes Solution No image transmission to remote location Defective camera Connect a local monitor to the camera and check the camera function Faulty cable connections Check all cables plugs contacts and connections Incorrect encoder stream property set for connection to hardware decoder Select the H 264 MP SD option on the Encoder Streams configuration page No connection established no The unit s configuration Check all configuration parameters image transmission Faulty installation Check all cables plugs contacts and connections Wrong IP address Check the IP addresses terminal program Faulty data transmission within the LAN Check the data transmission with ping The maximum number of connections has been reached
32. to the system earth of the installation U S A section 810 of the National Electrical Code ANSI NFPA No 70 provides information regarding proper grounding 12 VDC 24 VAC power source This unit is intended to operate with a limited power source The unit is intended to operate at either 12 VDC or 24 VAC if PoE is not available User supplied wiring must be in compliance with electrical codes Class 2 power levels PoE Use only certified PoE devices Power over Ethernet can be connected at the same time as a 12 VDC or 24 VAC power supply If auxiliary power 12 VDC or 24 VAC and PoE are applied simultaneously the camera selects auxiliary input and shuts off the PoE Type label The type label is located on the side of the camera module Bosch Security Systems Installation Manual AM18 Q0637 v1 0 2012 12 8 en Safety FLEXIDOME HD VR 1 5 FCC amp ICES compliance FCC amp ICES Information This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a partic
33. ular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures reorient or relocate the receiving antenna increase the separation between the equipment and receiver connect the equipment into an outlet on a circuit different from that to which the receiver is connected consult the dealer or an experienced radio TV technician for help Intentional or unintentional modifications not expressly approved by the party responsible for compliance shall not be made Any such modifications could void the user s authority to operate the equipment If necessary the user should consult the dealer or an experienced radio television technician for corrective action The user may find the following booklet prepared by the Federal Communications Commission helpful How to Identify and Resolve Radio TV Interference Problems This booklet is available from the U S Government Printing Office Washington DC 20402 Stock No 004 000 00345 4 AM18 Q0637 v1 0 2012 12 Installation Manual Bosch Security Systems FLEXIDOME HD VR Safety en 9 1 6 MicroSD cards Bosch Security systems recommends that local storage on microSD card should only be used for alarm recording and Automatic Network Replenishment ANR applications To minim
34. wise leave the cap in place Bosch Security Systems Installation Manual AM18 Q0637 v1 0 2012 12 20 en Installation FLEXIDOME HD VR 5 2 2 Flush mount 105 4 13 WR PCD 133 5 25 To flush mount the camera in a wall or ceiling 1 Use the mounting template to mark out the recess and to mark the holes indicated in the drawing The PCD is 133 mm 5 25 in 2 Cut out the recess 3 Drill three holes with a diameter of 8 mm 0 3 in 4 Insert the supplied plugs into the holes 5 Partially insert two screws into the mounting holes AM18 Q0637 v1 0 2012 12 Installation Manual Bosch Security Systems FLEXIDOME HD VR Installation en 21 5 3 6 Using one of the keyholes hang the mounting base of the camera module on one screw temporarily tilt the base slightly to gain access to the cable connections 7 Make the connections as outlined in section 5 3 below Connections CAUTION Isolate unused power wires individually to prevent short circuits Check the type label on the the camera module for the correct power ratings 5 3 1 Make the connections Connection box The unit has connection terminals on flying leads In wet or outdoor installations make use of a field wiring box with NEMA Type 4X or IP66 protection level or better 1 Make the connections inside a water tight compartment Isolate unused power wires individually 2 After connections are made
Download Pdf Manuals
Related Search