User Manual User Manual
Contents
1.2. EQUIPMENT User Manual Hot Dog Roller Grills Models RG1812 RG1824 7 2015 Please read and keep these instructions Indoor use only www AvantcoEquipment com 1 User Manual Product Features EQUIPMENT VANTCO 1 Avantco Equipment s hot dog roller grills feature a convenient temperature control that makes them energy efficient and power saving 2 The high torque motor drive system is designed for long lasting durability 3 The seven and nine roller grills have separate controls for front and back rollers 4 The bottom is made of stainless steel with an extractable stainless steel oil plate which keeps the machine easy to clean Technical Specifications Model Dimensions LxWxH Voltage V Power W RG1812 22 7 8 x 8 3 4 x 8 3 4 120V 60HZ 430 RG1824 22 7 8 x 15 3 4 x 8 3 4 120V 60HZ 750 Parts Identification Note RG1824 Model Shown RG1812 Model has 5 Rollers and 1 Temperature Knob Rollers Switch Panel Right Knob Handles the back rollers Left Knob Handles the front rollers Hot Dog Quantity 12 24 __ Bearing Rollers Oil Plate Rear Heating Indicator Light Front Heating Indicator Light 222 Footpad www AvantcoEquipment com EQUIPMENT VANTCO User
3. Manual Important Safeguards 1 Thoroughly read this instruction manual prior to first use 2 Do not submerge unit and or cord in water or any other liquids Failure to heed this warning may result in electric shock unit damage and or bodily injury 3 Close supervision is Suggested when unit is in use especially when children are present 4 Check to ensure unit is in off position and unplugged when not in use or prior to cleaning Allow grill to cool com pletely before cleaning 5 Do not operate if the machine suffers serious damage or malfunctions Contact dealer for repair or adjustment 6 It is recommended that you use only manufacturer issued parts and accessories with this unit Using unapproved parts may result in damage or injury 7 Do not use outdoors 8 Do not let cord hang over the edge of table or counter Do not let it touch any hot surfaces 9 Do not place appliance on or near gas or electric burners or heated ovens 10 Securely insert plug into outlet When unplugging be sure to remove plug only Never pull by the power cord Installation 1 To avoid equipment or electrical damage make certain that the nameplate voltage is the same as the outlet voltage 2 Electrical and grounding connections must be in compliance with the applicable portions of the electrical code 3 Prior to first use it is recommended that you clean the rollers of the machine with a cotton or wipe pad Operation Guide 1 Evenl
4. oids this Warranty This warranty does not apply to and Avantco is not responsible for any warranty claims made on products sold or used outside of the United States 4 www AvantcoEquipment com AVANTCO User Manual Circuit Diagram RG1824 il gt a A 1 R9 Ri HL2 www AvantcoEquipment com 5 User Manual AVANTCO Parts Diagram 6 www AvantcoEquipment com EQUIPMENT VANTCO Parts List No Name 1 Bolt 2 Bolt 3 Foot 4 Glass cotton 5 Housing 6 Round head screw 7 Side board 8 Insulated plate 9 Heating element supporter 10 Heating element supporter 11 Coil 12 Power cord with plug 13 Tube 14 Tube pin 15 Tube with wheel 16 Heating element 17 Heating element fixer 18 Bolt 19 Side board 20 Chain 21 Bolt 22 Motor wheel 23 Motor 24 Mesh supporter 25 Indication light 26 Switch 27 Thermostat 28 Bolt 29 On off 30 Oil Pot www AvantcoEquipment com User Manual Specification M4 x 8 Galvanized M5 x 16 stainless steel Rubber Glass cotton Stainless steel M4 x 8 Stainless steel Stainless steel Aluminum Plated Aluminum Plated Plastic 16 cord NEMA 5 15 PLUG 112 Va 11 2 y 1 8 118 x 193 4 120V 80W Stainless steel M4 x 8 Galvanized Stainless steel 3 2mm a M4 x 8 Galvanized 120V 5 6round min Plastic 16A 250V yellow 41 EGO M4 x 6 Galvanized Qty PCS 6 N A N OQ 8 ok 18 18
5. scouring pads because this may damage the rollers surface and the particles may get into the bearing y Attack tough grease oil and carbon with this ready to use carbonizer 4 N OBLE FORMULA D and degreaser Its unique formula is designed to clean ovens grills CMAN m hoods and a wide variety of other surfaces Suggestions 1 Hot dogs must be fully unfrozen 2 Do not leave hot dogs on the grill too long to ensure the best results If warming for more than four hours the hot dogs may become thick and hard Limited Warranty All equipment which is sold under Avantco trademark and used for commercial purpose is warranted against defects in materials and workmanship The warranty runs for one year from the date of original installation and is for the benefit of the original purchaser only All other Warranties Expressed or Implied Statutory or Otherwise including Without Limitation any implied Warranty of Merchantability or Fitness for Purposes are excluded The Seller shall in no event be liable for direct indirect or consequential damages in connection with Avantco commercial products This warranty is not effective if damage occurs because of accident carelessness improper installation lack of proper set up Supervision when required or if the equipment is installed or operated in any manner contrary to the installation and operating instructions Work performed by unauthorized personnel or unauthorized service agencies v
6. y place unfrozen hot dogs on the rollers 2 RG1812 The knob controls all five rollers RG1824 The left knob controls the front rollers and the right knob controls the back rollers Both rows may be used for operation during high volume use 3 Turn the roller switch on the control plate to ON This switch controls the rotation of the rollers 4 Turn the knob to the desired heat level After 40 minutes of heating the hot dogs turn the temperature control knob lower to continuously keep warm 5 The heating duration depends on the hot dogs quality Please adjust as needed or required Average heating duration is 40 minutes but may vary www AvantcoEquipment com 3 EQUIPMENT User Manual VANTCO Cleaning Instructions 1 To avoid electric shock or scalding unplug the power cord and allow the unit to cool before cleaning 2 Do not submerge the hot dog grill in water or directly apply liquids to clean unit 3 When cleaning the rollers wipe from the end of the rollers to the center This will reduce grease and particles from getting into the bearings Proper cleaning may extend the life of the unit and extend the period between routine maintenances 4 For product with high fat or sugar content clean the rollers every 3 4 hours 5 Remove the hot dogs from the rollers when wiping Do not touch the heated rollers directly as this may result in burn ing or scalding 6 Do not clean roller tubes with abrasive cleaners or
Download Pdf Manuals
Related Search