AX2065P - Axiom Pro Audio
Contents
1. USER MANUAL AX2065P passive vertical array loudspeaker KEY FEATURES e High output line array element e Compact size very good output to weight ratio e High quality low compression low distortion HF driver e Very stable horizontal coverage e Transmission Line back loading for clean mid bass reproduction e Natural sound Transmission Line HF projection wave forming device INTRODUCTION The AX2065P Vertical Line Array element is designed for a wide range of sound reinforcement applications where a flexible and easy to use vertical array systems is needed The AX2065P has been designed both for rental live sound applications and for fixed installations and has been engineered for the simplest use possible but without sacrificing anything in sound quality and performance The high frequency range is reproduced by a low distortion compression driver equipped with very light weight Titanium diaphragms and a special new suspension design for very natural sound A transmission line wave forming waveguide has been used to load the HF driver in order to provide a detailed and natural sound and to achieve a long distance HF projecting capacity The two 6 5 woofers employed in the reproduction of the mid bass range are equipped with very light weight cones and rubber suspension to extend the low frequency response The lightness of the diaphragm is furthermore improved by the use of aluminium voice coil instead of conventional copper Th2. Axiom AX2065 and SW215 Loudspeakers KPTAX2065 Fly bar for Axiom AX2065 only AXFEETKIT Kit Of 69cs BOARDACFO1 M10 foot for stacked installation KPAX265 Pole Adaptor KP010 0 to 10 tilt adaptor DHSS10M20 Sub Speaker 35mm Pole with M20 screw RAINCOV2065 Rain cover for input sockets see http www axiomproaudio com for detailed description and other available accessories SPARE PARTS NL4MP 94SP12265 PLG716 91CRAIN3 AX2065 used as conventional system Neutrik Speakon panel socket Locking Pin for AX2265 Straight Shackle 16 mm for Fly bar Crossover protection module MAX 2x AX2065 KPAX265 KP010 DHSS10M20 1x SW215 98AXM6W16 6 5 woofer 1 5 VC 98DRI2065 1 4 2 5 compression driver 98MBN2065 titanium diaphragm for 1 4 driver REAR PANEL INPUT Power input for the external amplifier The AX2065P does not include a passive crossover for filtering the signal but only an internal protection that applies a gentle high pass filtering and a limitation for excessive power on the HF section The connections are the following ae AXIOM VERTICAL ARRAY ELEMENT 1s 1 gt MFB 0 OW AES 22 gt HBA 75W AES _ LINK Power output in parallel with the INPUT socket for connecting the unit to another speaker The number of AX2065P cabinets that can be connected in parallel depends on the amplifier load capacity A N WARNING In case of us
3. for the centre region of a bigger flown array It can be used also for stacked arrays NOTE in this preset the subwoofer SW215P is placed at the top of the flown array in case the sub is placed on ground an additional delay time must be considered read the PC260 OUT section further in this manual LONG THROW PRESET name 2065_4 1_LT01 pcf This PRESET can be used in arrays bigger than 6 or 8 boxes and loaded in the top 1 or 2 boxes in order to obtain a more even distribution of the sound pressure especially if they point very far away or to the upper deck of a large theatre SINGLE DOWN FILL PRESET name 2065 _4 1 SD01 pcf This PRESET which features a much smoother high frequency response can be loaded in the bottom boxes usually 1 or 2 boxes of a large flown array in order to reach conveniently the audience close to the stage It can be used also for the conventional system consisting 1x SW215P at ground and 2x AX2065P on pole This preset could be very useful also when the box is used just on its own as a Front Fill element in the front of very large stages KPTSW215 STACKED ARRAY OOO 2C0OOOOCOO00000O System Company Label Position Orientation Weight Setup Box Count Pinpoint Mode Pinpoint Number Remaining Vertical Angle Bottom Angle Above Ground Box 1 Box 2 Box 3 Box 4 Box 5 System Company Label Position Orientation Weight Setup Bo
4. OW L and LOW R can be adjusted in relation to the MID HIGH outputs for the optimal alignment when the system is installed in a different position WARNING The DELAY difference between MID and HIGH outputs must always be 93 mm HIGH after MID If you modify the MID delay to align the tops with the subs remember always to set the HIGH delay accordingly 93 mm w cu Far j li F w oe F a iy a iy a a 1 i f i 3 1 7 Ca a ki i Ga a a B a a a i h F i i i _ a A n GEQ this is the graphic equalizer on the processor inputs to be used for equalizing the whole system It can be used for adjusting the system s response or for fixing particular frequency problems in the environment where the system is installed The AX2065P preset has been prepared in order to obtain the best performance from the system so we suggest to avoid extreme use of the GEQ PEQ this is a full parametric 5 band equalizer on the processor s inputs Each filters can be set also as shelving notch allpass high pass and lo pass so this equalizer can be used to optimize the system response according to the environment characteristics including temperature humidity and absorption due to the audience response so we suggest to do not change its parameters and use it as it is already set LIMITED WARRANTY Proel warrants all materials workmanship and proper operation of this product for a period of two years from th
5. TIONS TO USE GROUPS If you use more than one PC260 processor to drive the same vertical array system as in the example above you must always set the same parameters of the input panel for both processors levels and delay and any other parameter must be always the same The right way to this is the following 7 PRONeT Devices Tree View Virtual ft Group 1 1 Be sure that each PC260 has not assigned to any device group 2 Load the STANDARD SINGLE DOWN FILL LONG THROW preset on each dedicated PC260 3 Assign every PC260 to the same device group Now any modification made on one PC260 is repeated also File Connection Device Groups Window Help ide 9 O mB OPNE STANDARD 1 2065_4 1_ST1 Not Active Group 1 DOWN FILL 1 2065_4 1_SD1 Not Active Group 1 on all the others assigned to the same group Connection Offline Edit Mode User Mode Lock Level Lock Not Enabled Group Link Status Active WARNING After you have assigned all the PC260 to the same group do not load or save preset because what you do on one unit will be repeated also on the others for load and save operations you must remove the units from the groups EDIT PARAMETERS In the PC260 presets some parameters can be customized and some other are protected this ensure a Safe operation of the system Here is a brief description of customizable parameters IN In this screen you can adjust
6. TRAIGHT SHACKLE Rigging Box Count Weight a1 Pinpoint Detta 0 26 ae Cabinet Gain Angle a1 AX2065 SuspBar ia 1 AX2065 STD o _ 2 AX2065 STD x o 3 AX2065 STD jo 4 Ax2065 STD x 0 7 Follow the sequence in the figure for fixing the fly bar at the first box Usually this is the first step before lifting up the system Be careful to insert properly all the locking pins 1 2 and 3 4 then the shackle 5 in the right holes as specified by the aiming software When lifting the system always proceed gradually step by step paying attention to secure the fly bar to the box and the box to the other boxes before pulling up the system this makes easier to insert properly the locking pins Also when the system is released down unlock gradually the pins During the lifting be very careful to not let the cables enter the space between one enclosure and the other as their compression could cut them Fly bar suspension and angle setup centre of gravity The first figure shows where the normal centre of gravity is with HINGE BAR OF PREVIOUS BOX one box or several boxes arranged in a line Usually the boxes are arranged to make an arc for the best coverage of the audience so the center of gravity moves backward The aiming software suggests the ideal suspension pinpoint taking into account this behaviour fix the straight shackle in thi
7. The design of EASE Focus is targeted at the end user It allows the easy and quick prediction of the array performance in a given venue The scientific base of EASE Focus stems from EASE the professional electro and room acoustic simulation software developed by AFMG Technologies GmbH It is based on the EASE GLL loudspeaker data file required for its use AXIOM_AX Series_v2_1 GLL please note that the version must be 2 1 or more The GLL file contains the data that defines the Line Array with regard to its possible configurations as well as to its geometrical and acoustical properties Download the EASE Focus 2 app from the AXIOM website at http www axiomproaudio com clicking on downloads section of the product Use the menu option Edit Import System Definition File to import the file AXIOM_AX Series_v2_1 gll from the installation Data folder the detailed instructions to use the program are located in the menu option Help User s Guide Note Some windows system can require the NET Framework 4 that can be download from microsoft website at http www microsoft com en us download default aspx WARNING CAREFULLY READ THE FOLLOWING INSTRUCTIONS AND CONDITION OF USE e This loudspeaker is designed exclusively for Professional audio applications The product must be installed by qualified personal only e Proel strongly recommends that this loudspeaker cabinet be suspended taking into consideration all current National Federal State and L
8. are allowed to be set up as ground stack In the stack configuration you have to use the three optional BOARDACFO1 feet and the fly bar must be mounted upside down on the ground Coupling system in the front do not require any adjustment using two locking pins each loudspeaker box is fixed to the previous The slotted bar in the back is inserted in a U shaped frame which features a series of numbered holes Sliding the slotted bar in the U shaped frame of the next loudspeaker and inserting a locking pin in one of the numbered holes it is possible to adjust the relative splay angle between two adjacent loudspeakers in the array column The optimal splay angles can be simulated using the EASE Focus 2 software System Processing basic instruction The AX2065P system does not feature passive filters so it needs an external processor to take care of the filtering the time alignment and the speaker protection For the system s processing PROEL PC260 digital loudspeaker processor must be used loaded with dedicated presets for the correct system operation which offer the best starting point for setting the time alignment the gain and the equalization For detailed instructions about the use of PC260 refer to its user s manual The presets can be download from the AXIOM web site in the AX2065P download section STANDARD PRESET name 2065_4 1_ST01 pcf This PRESET is suitable for vertical flown arrays that may range from 4 to 8 boxes or
9. away from water rain and high humidity places This product should be site away from heat sources such as radiators lamps and any other device that generate heat This product should be located so that its location or position does not interfere with its proper ventilation and heating dissipation Care should be taken so that objects and liquids do not go inside the product The product should be connected to a power supply mains line only of the type described on the operating instructions or as marked on the product Connect the apparatus to a power supply using only power cord included making always sure it is in good conditions WARNING The mains plug is used as disconnect device the disconnect device shall remain readily operable Do not cancel the safety feature assured by means of a polarized line plug one blade wider than the other or with a earth connection Make sure that power supply mains line has a proper earth connection Power supply cord should be unplugged from the outlet during strong thunderstorm or when left unused for a long period of time CE CONFORMITY Proel products comply with directive 2004 108 EC EMC as stated in EN 55103 1 and EN 55103 2 standards and with directive 2006 95 CE LVD as stated in EN 60065 standard PROEL S p A World Headquarter Via alla Ruenia 37 43 64027 Sant Omero Te ITALY Tel 39 0861 81241 Fax 39 0861 887862 www axiomproaudio com AXIOM
10. e Vertical Coverage Angle Maximum Peak SPL 1m Electrical Nominal Impedance Minimum Impedance Power Handling Continuous Power Handling Peak AES Pink Noise Power revision 2014 12 5 Two 6 5 165 mm 1 5 38 mm aluminium voice coil 160 each paralleled One 1 4 driver 2 5 64 mm edgewound voice coil titanium diaphragm 8Q each paralleled 80 Hz 18 kHz Processed 99 dBSPL LF 108 dBSPL HF 110 6 dB 12 6 dB 129 dB 8Q LF 8Q HF 7 2 Q 340Hz LF 72 2 5kHz HF 400 W LF 75 W HF 800 W LF 150 W HF Connector Type Input Wiring Mechanical Width Height Depth Taper angle Construction Paint Suspension system Front Suspension Back Suspension Net Weight Neutrik Speakon NL4 x 2 LF Pin 1 1 HF Pin 2 2 583 mm 22 95 244 mm 9 60 481 mm 18 93 5 15 mm reinforced Phenolic Birch High resistance water based paint Aluminium Fast Link structure with Fast Pin High Strength Steel with Fast Pin 19 2 Kg 42 32 lbs MECHANICAL DRAWING OPTIONAL ACCESSORIES AXCASE05 AXCASE06 NL4FX AX2065A SW215P SW215FP PC260 USB2CAN Carrying Case for 4 box unit Flying Bar Carrying Case for 4 box unit Neutrik Speakon PLUG Active vertical array loudspeaker Passive Subwoofer Flyable Passive Subwoofer 2 in 6 out digital loudspeaker processor PRONET network converter 24 4 cm 9 60 KPTSW215 Fly bar for
11. e original date of purchase If any defects are found in the materials or workmanship or if the product fails to function properly during the applicable warranty period the owner should inform about these defects the dealer or the distributor providing receipt or invoice of date of purchase and defect detailed description This warranty does not extend to damage resulting from improper installation misuse neglect or abuse Proel S p A will verify damage on returned units and when the unit has been properly used and warranty is still valid then the unit will be replaced or repaired Proel S p A is not responsible for any direct damage or indirect damage caused by product defectiveness e This unit package has been submitted to ISTA 1A integrity tests We suggest you control the unit conditions immediately after unpacking it e If any damage is found immediately advise the dealer Keep all unit packaging parts to allow inspection e Proel is not responsible for any damage that occurs during shipment e Products are sold delivered ex warehouse and shipment is at charge and risk of the buyer e Possible damages to unit should be immediately notified to forwarder Each complaint for package tampered with should be done within eight days from product receipt SAFETY INSTRUCTIONS To reduce the risk close supervision is necessary when the product is used near children Protect the apparatus from atmospheric agents and keep it
12. g the slotted bar in the U shaped frame of the next loudspeaker and inserting a locking pin in one of the numbered holes it is possible to adjust the relative splay angle between two adjacent loudspeakers in the array column KPTSW215 FLY BAR AND ACCESSORIES M10 FOOT FOR STRAIGHT SHACKLE 16mm g STACKED INSTALLATION PA OPTIONAL 16mm IDENTIFICATION AND S KPTSW215 fly bar maximum capacity is 540 Kg 1190 Ibs with the 0 angle It can support with a safety factor of 10 1 up to e 8 AX2065A 8 AX2065P flybar from 0 to 10 e 12 AX2065A flybar from 0 to 10 e 2 SW215AF 4 AX2065A 4 AX2065P flybar at 0 e 2 SW215AF 8 AX2065A flybar at 0 e 6 SW215AF flybar from 0 to 5 KPTSW215 can be used for stacked array see further on this manual ad Q FRONT BOX PIN ATTACHMENT SUSPEND HOLE INDICATOR KPTAX2065 fly bar maximum capacity is 200 Kg 441 Ibs with the 0 angle It can support with a safety factor of 10 1 up to e 6 AX2065 active or passive flybar from 0 to 10 KPTAX2065 can NOT be used for stacked array NOTE The figures illustrate the KPTWS215 only KPTAX2065 use is similar with capacity limitations SUSPEND HOLES FRONT BOX 7 PIN ATTACHMENT REAR BOX PIN ATTACHMENT AXIOM KPTSW215 FLY BAR FOR FLOWN ARRAY OD O76 OS 22 Ge GE S 3 Se O ea CENTRE OF GRAVITY KPTSW215 FLOWN PINPOINT SINGLE PINPOINT FOR S
13. ind effects must be taken into account Wind load produces additional dynamic forces acting on the rigging components and the suspension which may lead to a dangerous situation If according to the forecast wind forces higher than 5 bft 29 38 Km h are possible the following actions have to be taken lt q The actual on site wind speed has to be monitored permanently Be aware that wind speed typically n d increases with height above ground press an Suspension and securing points of the array should be designed to support double the static load in order insert to withstand any additional dynamic forces WARNING Flying loudspeakers overhead at wind forces higher than 6 bft 39 49 Km h is not recommended If the wind force exceeds 7 bft 50 61 Km h there is a risk of mechanical damage to the components 4 which may lead to a dangerous situation for persons in the vicinity of the flown array Stop the event and make sure that no person remains in the vicinity of the array Lower and secure the array release and j lock Stacked installation KPTSW215 only WARNING A N e The ground where the KPTSW215 Fly bar serving as ground support is placed needs to be absolutely stable and compact e Adjust the feet so to lie the bar perfectly horizontal e Always secure ground stacked setups against movement and possible tipping over e A maximum of 4 x AX2065 cabinets with the KPTSW215 Fly bar serving as ground support
14. ing the AX2065P passive module linked with an AX2065A active module DO NOT LINK ANY OTHER AX2065P Useful tools to set up properly a vertical array system This is a list of tools that can be very useful to set properly a vertical array system CABLE TESTER It is a good practice to check all cables before each installation because even one faulty cable can compromise heavily the system performance INCLINOMETER WITH LEVER This tool can be used to verify the vertical array angle It can be used at the top or at the bottom of the array In this case you have to sum all splay angles so the maximum precision is needed for aiming the vertical array particularly for long throw applications LASER DISTANCE METER This instrument can be useful to measure the height of the vertical array and to know the distance between FOH Subs and FOH Array for setting the delay time SMAART or similar acoustic measurement system madl V7 These are useful to measure delays phase and response of the system E E PREDICTION EASE Focus 2 To aim correctly a complete system we suggests to use always the Aiming Software EASE Focus 2 The EASE Focus 2 Aiming Software is a 3D Acoustic Modelling Software that serves for the configuration and modelling of Line Arrays and conventional speakers close to reality It only considers the direct field created by the complex addition of the sound contributions of the individual loudspeakers or array components
15. is ensure a fast reproduction of the mid range and of mid bass musical passages improving also the thermal capacity of the voice coil and consequently controlling the overall power compression The two 6 5 woofers are back loaded by a short hybrid transmission line that minimizes the effect of the box resonances and eliminates the boxy mid bass sound commonly obtained from regular bassreflex enclosures The crossover filter approach is based on a Constant Power technique Thanks to a particular phase combination between the two ways around the crossover frequency this approach is able to provide a very stable horizontal coverage and a very stable off axys sound image also minimizing unwanted effects around the crossover frequency The further application of phase linearization techniques combined to constant power crossover yield a linear phase response and a coherent time response This allows for a natural perception of acoustic instruments and voices and for an improved depth of the sound image TECHNICAL SPECIFICATION Acoustical 10 dB Power 70 W 0 7 dB 3 dB Power 350 W 1 8 dB 0 dB Power 700 W 3 5 dB Line Array Element LF Power Compression Short Transmission Line LF Back Loading Acoustic Transmission Line HF Waveguide System type Connectors Low frequency transducer High frequency transducer Frequency response 3 dB Sensitivity 2 83 V 1m 2 Pi Horizontal Coverage Angl
16. ocal regulations Please contact the manufacturer for further information e Proel do not accept any liability for damage caused to third parties due to improper installation lack of maintenance tampering or improper use of this product including disregard of acceptable and applicable safety standards e During assembly pay attention to the possible risk of crushing Wear suitable protective clothing Observe all instructions given on the rigging components and the loudspeaker cabinets When chain hoists are in operation ensure that there is nobody directly underneath or in the vicinity of the load Do not under any circumstances climb on the array AIMING and SUSPENDING INSTRUCTIONS KPTSW215 FLY BAR ASSEMBLY SEQUENCE Fly Bar and accessories x The AX2065 Systems are built to allow the suspension of array with variable shape and dimensions Thanks to a suspension mechanism designed to be functional flexible and safe each system must be suspended or stacked using the KPTSW215 or KPTAX2065 fly bar The loudspeakers are linked together in a column using a series of couplers integrated in the frame of each enclosure Each system is set up properly both acoustically and mechanically only using the aiming software Coupling system in the front does not require any adjustment using two locking pins each loudspeaker box is fixed to the previous The slotted bar in the back is inserted in a U shaped frame which features a series of numbered holes Slidin
17. s position Note that the ideal aiming angle often doesn t correspond to the pinpoint there is often a little difference between ideal aiming and real aiming and its value is the Delta angle positive delta angle can be adjusted a little using two ropes negative delta angle are self adjusted a little because the cables weighs on the back of the array With some experience it s possible to consider preventively these required little adjustments During the flown set up you can connect the elements of the array to their cables We suggest to discharge the weight of the cables from the flying pinpoint by tying them with a textile fibre rope instead of letting them hang freely in this way the position of the array will be much more similar to the simulation produced by the software Pin locking and splay angles set up The figure below shows how to insert correctly the locking pin and how to set up the splay angle between loudspeakers Wind loads When planning an open air event it is essential to obtain current weather and wind information When LOUDSPEAKER SPLAY ANGLES SET UP LOCK THE PIN IN THE HOLE TO OBTAIN THE REQUIRED SPLAY ANGLE 0 1 2 3 4 5 jt DROP LINK o o ooo 6 BLOCK CAM 70 HOLE m gt G 8 BLOCK CAM HOLE 10 0 10 gt USE THIS HOLE TO LOCK THE HINGE BAR WHEN THE LOUDSPEAKER IS REST 95AXMO014 LOCKING PIN loudspeaker arrays are flown in an open air environment possible w
18. s well as the high frequency level lt lt bT NJ v DOWN FILL BOX PRESET OPERATIONS In order to optimize the array performances for this specific application the PRESETS should be loaded in different PC260 loudspeaker processors used in the following way Load the STANDARD preset in the first PC260 processor that drives the amplifiers j for the central boxes Load the LONG THROW preset in the second PC260 processor that drives the amplifies for the TOP 1 or 2 boxes in order to compensate the loss of power level and high frequencies of the program sent to the upper deck of the theatre Load the DOWN FILL SINGLE BOX preset in the third PC260 processor that drives the amplifiers for the BOTTOM box in order to smooth the high frequency content of the program sent to the audience close to the stage NOTE the audio signal send to all PC260 processors must be the same so their inputs must be linked with a XLR cable NOTE The outputs 1 and 2 of each PC260 are assigned always to drive the amplifiers for the SW215 subwoofers so you can use indiscriminately the output 1 and 2 of one of them 15 25 2350 25 EARE Apr 35 0 37 5 TOP BOX AX2065P PRESET RESPONSE LONG THROW SUBWOOFER OUTPUTS STANDARD dB SINGLE DOWNFILL 10K 20K Hz IMPORTANT INSTRUC
19. the input levels compressors limiters and delay The input range can be optimized in the 30 6 dB range The level is set after the AD conversion so if you have problems with an excessive input signal use the analog PAD button on the PC260 back panel The compressors are set in order to attenuate very high input signals the threshold is 12 dB ensuring a more transparent musical behaviour of the system limiting If needed the compressor threshold can be freely adjusted eee I i td FT cel uc jee ee jna jee aw jon eer Lee nae yy Lara S 7 ivir Pa Fa 1 ia Bnk aj Tie a kii kr inh E i bl isa ieee i ii rer C imm ma mm Ty AES a i iin 3 oa is all BL Fae l l I A Del LET r I sy qu Ae ppi BE amt T ki fi OUT in this page you can see the level of the output signals and the gain reduction if the Mmmm limiters are activated You can also trim 6 dB the output signals in order to adjust the balance of LF MF and HF ranges NEHN E HEIL E HEN i HL hi anh Ls H ima 1 1 i a a g a E k WARNING The limiter setting of PC260 and 2065 preset is set for the use of 32 dB fixed gain power amplifiers contact PROEL if you need a different setting The delays are set for the optimal alignment of a standard flown configuration with the vertical array on top of the subwoofers If needed the delay of the subwoofers L
20. x Count Pinpoint Mode Box 4 Box 3 Box 2 Box 1 Box Type Frame SW215F AX2065 STD AX2065 STD AX2065 STD AX2065 STD Box Type AX2065 STD AX2065 STD AX2065 STD AX2065 STD Frame AXIOM AX Series PROEL S p A AXIOM AX Series X 0 00 m Y 0 00 m Z 4 00 m Hor 0 0 Ver 5 1 164 30 kg SW215 SuspBar 5 Best Pinpoint 7 0 4 23 1 2 31m Gain 0 0 dB 0 0 dB 0 0 dB 0 0 dB 0 0 dB AXIOM AX Series PROEL S p A AXIOM AX Series X 0 00 m Y 0 00 m Z 0 80 m Hor 0 0 Ver 0 0 96 00 kg AX2065 StackBar 4 No Pinpoint Gain 0 0 dB 0 0 dB 0 0 dB 0 0 dB max splay angle 10 ye T maxs Rigging Angle 0 0 1 Do 10 max splay angle 10 max splay angle 10 play angle 10 Aiming Angle 5 1 5 1 5 1 6 1 8 1 18 1 Rigging Angle 0 1 2 5 Aiming Angle 8 0 8 0 7 0 5 0 0 0 EXAMPLE OF INSTALLATION IN A THEATRE WITH BALCONY Here below you can see an example of the use of different PRESETS in an AX2065 flown array installed in a big theatre with balcony The TOP BOXES of the array are aiming at the balcony while the DOWN FILL box is aiming at the audience close to the stage 1 175 202 15 0 TOP BOXES the power level at the end of the balcony is lower as well as the high frequency level 10 0 DOWN FILL BOXES the power level in the proximity of the stage is higher a
Download Pdf Manuals
Related Search