Home
TFT Controller Board VNS Series User`s Manual
Contents
1. TRACKING INFORMATION TUNING LANGU AGE CLOCK 125 AUTO TRACKING CLOCK r PHASE Using the OSD board press MENU to display the OSD main menu Use DOWN or UP to navigate to the FUNCTION menu Press EXIT VIDEO to select the FUNCTION menu Use DOWN or UP to navigate through the FUNCTION menu Press EXIT VIDEO to select TRACKING or INFORMATION Note TUNING menu is not available FUNCTION TRACKING AUTO TRACKING Auto tracking attempts to adjust the best condition of clock and phase however it depends on the image displayed If the auto adjusted image is not satisfactory then manual fine tune is required Note PC graphics card vary from manufacturer so the TFT controller board may not auto adjust the clock and phase Manual clock and phase adjust is required FUNCTION CLOCK CLOCK 0 Minimum clock adjustment for horizontal size 250 Maximum clock adjustment for horizontal size FUNCTION PHASE PHASE 0 Minimum phase adjust to remove noise or sharpen image 31 Maximum phase adjust to remove noise or sharpen image FUNCTION INFORMATION Displays current resolution and refresh frequency VSYNC Page 18 of 26 VNS22 Series User s Manual Revision 1 1 Optrex America Ine 5 3 3 OSD Menu Tree for Video Mode S Video and Composite Video Note TRACKING and TUNING adjustments are not available in the Video mode S Video and Composite Video January 23 2004 Page 19 of 26 VNS22 S
2. 59 DC power jack Video Input J6 Molex 53015 05 2 0mm 5P RA Power Out not populated J11 Molex 5268 03 2 5mm 3P RA Control Out not populated J15 Molex 53015 11 2mm 11P RA January 23 2004 Page 11 of 26 VNS22 Series User s Manual Revision 1 1 Optrex America Ine 4 3 VNS Series Board Connector Pin Descriptions 53015 08 Molex 51004 08P Molex J3 Connector Inverter Mating connector Pin No Function Pin No Function 1 Brightness adjust 5 GND 2 Backlight on off 6 GND 3 GND 7 12V 4 5V 8 12V J4 Connector OSD 53015 12 Molex Mating connector 51004 12P Molex Pin No Function Pin No Function 1 VCC 5 0V 7 LED Green 2 Menu 8 Reserved 3 Menu down 9 Reserved 4 Menu up 10 Power S W 5 Source menu select 11 GND 6 LED Red 12 Reserved J9 Connector VGA I F 1 53015 14 Molex Mating connector 51004 14P Molex Pin No Function Pin No Function 1 Red 8 HSYNC 2 GND 9 VSYNC 3 Green 10 GND 4 GND 11 SDA 5 Blue 12 SCLK 6 GND 13 GND 7 GND 14 5V January 23 2004 Page 12 of 26 VNS22 Series User s Manual Revision 1 1 Optrex America Ine J2 Connector VGA I F 2 DHSL 15 Leoco Mating connector DHPD 15 Leoco Pin No Function Pin No Function
3. PICTURE COLOR TEMPERATURE COLOR TEMPERATURE Standard 9300K Reset User 6500K e Press MENU again to save settings e Use DOWN or UP to select GEOMETRY or FUNCTION menu or press MENU again to exit the OSD main menu Page 16 of 26 VNS22 Series User s Manual Revision 1 1 E Optrex America Ine January 23 2004 5 3 2 2 GEOMETRY Menu GEOMETRY GEOMETRY H POSITION 58 H POSITION H POSITION 4 V POSITION V POSITION AUTO POSITION AUTO POSITION Using the OSD board press MENU to display the OSD main menu Use DOWN or UP to navigate to the GEOMETRY menu Press EXIT VIDEO to select the GEOMETRY menu Use DOWN or UP to navigate through the GEOMETRY menu Press EXIT VIDEO to select HPOSITION VPOSITION or AUTO POSITION option o When selecting HPOSITION and VPOSITION use DOWN or UP to adjust the desired value o When selecting AUTO POSITION image is automatically centered GEOMETRY HPOSITION HPOSITION 0 Maximum Shift Left 31 Maximum Shift Right GEOMETRY VPOSITION VPOSITION 0 Maximum Shift Up 31 Maximum Shift Down GEOMETRY AUTO POSITION AUTO POSITION Automatically centers image on screen Press MENU again to save settings Use DOWN or UP to select FUNCTION or PICTURE menu or press MENU again to exit the OSD main menu Page 17 of 26 VNS22 Series User s Manual Revision 1 1 January 23 2004 Optrex America Ine 5 3 2 3 FUNCTION Menu oS FUNCTION TRACKING
4. iee Page 14 of 26 VNS22 Series User s Manual Revision 1 1 7 00 January 23 2004 YZ Optrex America Ine 5 3 OSD Users Manual 5 3 1 Changing Video Input Source With power supplied to VNS Series Controller Board press the EXIT VIDEO button on the OSD Board to toggle the video source input The sequence is PC Analog RGB gt Composite Video gt S Video gt PC Analog RGB 5 3 2 OSD Menu Tree for Analog RGB Mode PC Note TUNING adjustment is not available in the Analog RBG PC mode 5 3 3 PC Mode Analog RGB OSD Options January 23 2004 Page 15 of 26 VNS22 Series User s Manual Revision 1 1 Optrex America Ine January 23 2004 5 3 2 1 PICTURE Menu tH EES as eal PICTURE PICTURE CONTRAST 3 CONTRAST CONTRAST BRIGHTNESS BRIGHTNESS COLOR TEMPERATURE COLOR TEMPERATURE 4 PICTURE COLOR TEMPERATURE 9300K CONTRAST MODE STANDARD BRIGHTNESS COLOR TEMPERATURE CG Jsing the OSD board press MENU to display the OSD main menu ress EXIT VIDEO to select the PICTURE menu se DOWN or UP to navigate through the PICTURE menu ress EXIT VIDEO to select CONTRAST BRIGHTNESS or COLOR EMPERATURE option e Use DOWN or UP to adjust the desired value e o o o Svcd PICTURE CONTRAST CONTRAST 0 Minimum Contrast 31 Maximum Contrast PICTURE BRIGHTNESS BRIGHTNESS 0 Maximum Brightness 31 Minimum Brightness
5. 1 BLUE 1 12 GND 32 GND 13 RED 2 33 BLUE 2 14 RED 3 34 BLUE 3 15 RED 4 35 BLUE 4 16 RED 5 36 BLUE 5 17 RED 6 37 BLUE 6 18 RED 7 38 BLUE 7 19 GND 39 VCC 5 0V 20 GREEN 0 40 VCC 5 0V January 23 2004 Page 7 of 26 VNS22 Series User s Manual Revision 1 1 Optrex America Ine J8 Connector LCD I F 2 A3 34 2DSA Hirose Mating Connector DF11 34DS 2C Hirose Part No Function Pin No Function 1 GND 18 Green 5 even 2 Red 0 even 19 Green 6 even 3 Red 1 even 20 Green 7 even 4 Red 2 even 21 GND 5 Red 3 even 22 Blue 0 even 6 Red 4 even 23 Blue 1 even 7 GND 24 Blue 2 even 8 Red 5 even 25 Blue 3 even 9 Red 6 even 26 Blue 4 even 10 Red 7 even 27 GND 11 GND 28 Blue 5 even 12 Green 0 even 29 Blue 6 even 13 Green 1 even 30 Blue 7 even 14 Green 2 even 31 GND 15 Green 3 even 32 NC 16 Green 4 even 33 NC 17 GND 34 NC January 23 2004 Page 8 of 26 VNS22 Series User s Manual Revision 1 1 Optrex America Ine 4 1 2 LVDS Interface Board Optrex 8 4 XGA and 12 1 SVGA LVDS panels Connector 12507WR 20 Yeonho Electronics Pin No Function Pin No Function Pin No Function Pin No Function 1 GND 6 RxCLKIN 11 GND 16 RxINO 2 GND 7 RxCLKIN 12 RxIN1 17 GND 3 Reserved 8 GND 13 RxIN1 18 GND 4 Reserved 9 RxIN2 14 GND 19 VDD 5 GND 10 RxIN2 15 RxINO
6. 1 Red 9 NC 2 Green 10 NC 3 Blue 11 NC 4 GND 12 SDA 5 D GND 13 HSYNC 6 R GND 14 VSYNC 7 G GND 15 SCLK 8 B GND J1 Connector Power In 5268 02 Molex Mating connector 5264 02 Molex Pin No Function Pin No Function 1 12V 2 GND J6 Connector Video Input 53015 05 Molex Mating connector 51004 05 Molex Pin No Function Pin No Function 1 S Video Y 4 Composite 2 Composite 5 GND 3 S Video C J11 Connector Power Out 5268 03 Molex Matching connector 5264 03 Molex Pin No Function Pin No Function 1 12V 3 5V 2 GND January 23 2004 Page 13 of 26 VNS22 Series User s Manual Revision 1 1 WZ Optrex America Ine 5 OSD ON SCREEN DISPLAY BOARD DESCRIPTION 5 1 OSD Control Buttons NO 1 2 3 4 5 6 Function LED MENU DOWN UP EXIT VIDEO POWER LED Status display Green Normal operation mode Red Power stand by mode MENU Activate OSD menu or save OSD setting and EXIT DOWN Decrease setting or left shift the menu UP Increase setting or right shift the menu EXIT VIDEO Toggles video input source or selects a menu option POWER Turn on or off the main board 5 2 OSD Mechanical Dimensions Unit mm lt 125 00 gt bes 107 50 gt lt 91 00 gt lt 4 74 00 gt le 30 00 5 00 gt gt 20 00 A AA A Si as io S Er gt de 6 00 6 00 gt q 12 00
7. 20 VDD January 23 2004 Page 9 of 26 VNS22 Series User s Manual Revision 1 1 Optrex America Ine 4 1 3 XGA Interface Board Optrex 15 0 XGA TTL Panels Panel Side Flat Flex Cable gt Daughter Board Mounted on the VNS Series Pin Connectors Bottom View Refer to Section 4 1 1 for Bottom View header description J19 J18 Top View Connector Connector IRAAAARARAARAARnAA ZIF style Connection for Top View are described as follows J18 Connector IL FHR BF40S HF JAE PinNo Symbol Function PinNo Symbol Function 1 GND 21 GO6 Green Odd Data 2 VCC 22 GO7 Green Odd Data MSB 3 VCC 23 GND 4 ROO Red Odd Data LSB 24 BOO Blue Odd Data LSB 5 ROI Red Odd Data 25 BO1 Blue Odd Data 6 RO2 Red Odd Data 26 BO2 Blue Odd Data 7 RO3 Red Odd Data 27 BO3 Blue Odd Data 8 GND 28 GND 9 RO4 Red Odd Data 29 BO4 Blue Odd Data 10 ROS Red Odd Data 30 BOS Blue Odd Data 11 RO6 Red Odd Data 31 BO6 Blue Odd Data 12 RO7 Red Odd Data MSB 32 BO7 Blue Odd Data MSB 13 GND 33 GND 14 GOO Green Odd Data LSB 34 NC This pin should be open or GND 15 GOl Green Odd Data 35 HD Horizontal Sync 16 GO2 Green Odd Data 36 VD Vertical Sync 17 GO3 Green Odd Data 37 DENA Data enable 18 GND 38 GND 19 GO4 Green Odd Data 39 DCLK Pixel Dot Clock 20 GOS5 Green Odd Data 40 GND January 23 2004 Page 10 o
8. Optrex America Ine TFT Controller Board VNS Series User s Manual January 23 2004 Page 1 of 26 VNS22 Series User s Manual Revision 1 1 E3 CONTENTS FEATURES GENERAL DESCRIPTION VNS SERIES MECHANICAL DIMENSIONS BOARD DESCRIPTION 4 1 VNS Series Board Top View 4 1 1 TTL Interface Connection 4 1 2 LVDS Interface Board 4 1 3 XGA Interface Board 4 2 VNS Series Board Connector Styles Manufacturers 4 3 VNS Series Board Connector Pin Descriptions OSD ON SCREEN DISPLAY BOARD DESCRIPTION 5 1 OSD Control Buttons 5 2 OSD Mechanical Dimensions 5 3 OSD Users Manual 5 3 1 Changing Video Input Source 5 3 2 OSD Menu Tree for Analog RGB Mode PC 5 3 2 1 PICTURE Menu 5 3 2 2 GEOMETRY Menu 5 3 2 3 FUNCTION Menu 5 3 3 OSD Menu Tree for Video Mode S Video and Composite Video 5 3 3 1 PICTURE Menu 5 3 3 2 FUNCTION Menu 5 4 OSD Lamp Indication Complies with VESA DPMS Requirements FRAME FREQUENCY SETTING APPLICABLE TIMING COMPATIBILITY CONTACTS Optrex America Ine 11 12 14 14 14 15 15 15 16 16 17 20 21 22 22 22 23 23 January 23 2004 Page 2 of 26 VNS22 Series User s Manual Revision 1 1 YZ Optrex America Ine 10 PART NUMBERING SYSTEM 24 11 SUPPORTED BIOS and FIRMWARE SETTING 24 11 1 TTL Models LVDS Daughter Board Not Required 25 11 2 LVDS Models LVDS Daughter Board Required 25 12 DOCUMENT HISTORY 26 January 23 2004 Page 3 of 26 VNS22 Ser
9. all meet the specifications described in this document January 23 2004 Page 4 of 26 VNS22 Series User s Manual Revision 1 1 FB Optrex America Ine 3 VNS SERIES BOARD MECHANICAL DIMENSIONS 7 li X ca se I l n l 7 i l E i m a l 1 lol a m A ITT very ye DE gt j yy TI Td Note Connector locations may vary January 23 2004 Page 5 of 26 VNS22 Series User s Manual Revision 1 1 7 Optrex Amenica Ine 4 BOARD DESCRIPTION 4 1 VNS Series Board Top View J8 Connector J7 Connector LCD I F 2 LCD I F 1 15 0 XGA TTL Panel Only J2 Connector a VGA I F 2 lt J9 Connector VGA I F 1 Located below J2 J4 Connector OSD J1 Connector J3 Connector J6 Connector Power Input Inverter Video Input Note Connector locations may vary January 23 2004 Page 6 of 26 VNS22 Series User s Manual Revision 1 1 Optrex America Ine 4 1 1 TTL Interface Connection Optrex 8 4 VGA TTL 10 4 VGA TTL 15 0 XGA TTL panels J7 Connector LCD I F 1 A3 40PA 2DSA Hirose Mating Connector DF11 40DS 2C Hirose Pin No Function Pin No Function 1 VCC3 3V 21 GREEN 1 2 VCC3 3V 22 GND 3 GND 23 GREEN 2 4 DCLK 24 GREEN 3 5 GND 25 GREEN 4 6 VSYNC 26 GREEN 5 7 HSYNC 27 GREEN 6 8 DE 28 GREEN 7 9 GND 29 GND 10 RED 0 30 BLUE 0 11 RED 1 3
10. eries User s Manual Revision 1 1 Optrex America Ine 5 3 3 1 PICTURE Menu ES PICTURE PICTURE CONTRAST 15 CONTRAST CONTRAST y b BRIGHTNESS BRIGHTNESS SHARPNESS SHARPNESS COLOR COLOR TINT TINT Using the OSD board press MENU to display the OSD main menu Press EXIT VIDEO to select the PICTURE menu Use DOWN or UP to navigate through the PICTURE menu Press EXIT VIDEO to select CONTRAST BRIGHTNESS SHARPNESS COLOR or TINT option e Use DOWN or UP to adjust the desired value PICTURE CONTRAST CONTRAST 0 Minimum Contrast 31 Maximum Contrast PICTURE BRIGHTNESS BRIGHTNESS 0 Maximum Brightness 31 Minimum Brightness PICTURE SHARPNESS SHARPNESS 0 Minimum Sharpness 2 Maximum Sharpness PICTURE COLOR COLOR 0 Minimum Color 31 Maximum Color PICTURE TINT TINT GO R30 G30 RO e Press MENU again to save settings e Use DOWN or UP to select FUNCTION menu or press MENU again to exit the OSD main menu January 23 2004 Page 20 of 26 VNS22 Series User s Manual Revision 1 1 FB Optrex America Ine 5 3 3 2 FUNCTION Menu mo 8 FUNCTION TRACKING INFORMATION TUNING LANGUAGE e Using the OSD board press MENU to display the OSD main menu e Press EXIT VIDEO to select the FUNCTION menu e Use DOWN or UP to navigate through the FUNCTION menu INFORMATION is the only available option e Press EXIT VIDEO to select INFORMATION option FUNCTION INFORMATION Displays current
11. f 26 VNS22 Series User s Manual Revision 1 1 Optrex America Ine J19 Connector IL FHR BF36S HF JAE Pin No Symbol Function Pin No Symbol Function 1 GND 19 GE2 Green Even Data 2 TEST This pin should be open 20 GE3 Green Even Data 3 TEST Test signal output for only 21 GND 4 TEST internal test use 22 GE4 Green Even Data 5 GND 23 GE5 Green Even Data 6 GND 24 GE6 Green Even Data 7 REO Red Even Data LSB 25 GE7 Green Even Data MSB 8 REI Red Even Data 26 GND 9 RE2 Red Even Data 27 BEO Blue Even Data LSB 10 RE3 Red Even Data 28 BE1 Blue Even Data 11 GND 29 BE2 Blue Even Data 12 RE4 Red Even Data 30 BE3 Blue Even Data 13 RE5 Red Even Data 31 GND 14 RE6 Red Even Data 32 BE4 Blue Even Data 15 RE7 Red Even Data MSB 33 BES Blue Even Data 16 GND 34 BE6 Blue Even Data 17 GEO Green Even Data LSB 35 BE7 Blue Even Data MSB 18 GEI Green Even Data 36 GND 4 2 VNS Series Board Connectors Styles Manufacturers Item Ref No Vendor P N Description LCD I F 1 J7 Hirose A3 40PA2DSA 2mm 40P 2 Row Pin HDR LCD I F 2 J8 Hirose A3 34PA 2DSA 2mm 34P 2 Row Pin HDR VGA I F 1 J9 Molex 53015 14 2mm 14P RA VGA I F 2 J2 Leoco DHSL 15 15P D sub female OSD J4 Molex 53015 12 2mm 12P RA Inverter J3 Molex 53015 8 2mm 8P RA Power In J1 Molex 5268 02 2 5mm 2P RA DC Jack not populated JSP11 Dong hea EJ210 2 5 2
12. ies User s Manual Revision 1 1 YZ Optrex America Ine 1 FEATURES Resolution up to XGA Color 16 776 216 8bit color Expansion True XGA with expansion support from DOS VGA SVGA Input Signal Analog RGB Composite Video S Video Output Signal TTL standard and LVDS optional daughterboard Control Single control operated with transparent On Screen Display hereafter OSD user interface OSD provides full control of all relevant display and interface parameters Power Input 12VDC 10 Power Controller Board in Normal Mode 7W max Controller Board in Standby Mode 3W max Controller Board with display and inverter connected Varies with display and inverter Dimension 4 72 L x 3 94 W x 0 58 H 120mm L x 100mm W x 15mm H Temperature Operating 0 45 C storage 20 70 C Humidity 90 R H max Plug n Play DDC1 amp DDC2B Power management VESA DPMS 2 GENERAL DESCRIPTION This specification defines the characteristics and performance of the VNS Series TFT LCD controller board This product is capable of displaying XGA and lower resolutions 16 777 216 colors based on red green and blue analog video input signals Synchronization signals for the applicable resolution modes can be detected automatically in the range of 30 to 60 KHz horizontal and 56 to 75 Hz vertical The Synchronization signal can be applied as separate HSYNC and VSYNC Unless otherwise specified the product sh
13. ls LVDS Daughter Board Not Required Manufacturer Part Number Resolution Optrex T 51638D084 FW A A VGA Optrex T 51513D104U FW A A VGA Optrex T 51511D150 FW A A XGA 11 2 LVDS Models LVDS Daughter Board Required Manufacturer Part Number Resolution Optrex T 51639D084U FW A A XGA Optrex T 51512D121J FW A A SVGA Note Displays subject to change without notice Check our website for current product offering http www optrex com January 23 2004 Page 25 of 26 VNS22 Series User s Manual Revision 1 1 E3 Optrex America Ine 12 DOCUMENT HISTORY Revision Date Revision History 1 0 04 03 03 Initial specification 1 1 01 23 04 Added deleted available board part numbers January 23 2004 Page 26 of 26 VNS22 Series User s Manual Revision 1 1
14. nual Revision 1 1 YZ Optrex America Ine 8 COMPATIBILITY Many PC graphic cards exist in the marketplace In general the video signal of various PC graphics cards complies with VESA recommendations but some do not This TFT LCD controller board was designed under the assumption that the video signal is within VESA standards therefore this TFT controller board might not function properly with non standard timing 9 CONTACTS Contact in USA Address OPTREX America Inc 46723 Five Mile Road Plymouth MI 48170 2422 USA Tel 734 416 8500 Fax 734 416 8520 January 23 2004 Page 23 of 26 VNS22 Series User s Manual Revision 1 1 YZ Optrex America Ine 10 PART NUMBERING SYSTEM VNS XX YYYZZZZAAAA VNS TFT Controller Board Series VNS Version 1 XX Input source AO Analog I F only VO Video I F only AV Analog amp Video I F YYY Panel Size 8 4 12 1 10 4 or 15 0 ZZZZ Panel Resolution VGA SVGA or XGA AAAA Panel Interface TTL or LVDS VNS Series TFT Controller Board Part Numbers Available in Kits VNS AV 084VGATTL 00 VNS AV 084XGALVDS 00 VNS AV 121SVGALVDS 00 VNS AV 104VGATTL 00 VNS AV 150XGATTL 00 January 23 2004 Page 24 of 26 VNS22 Series User s Manual Revision 1 1 YZ Optrex America Ine 11 BIOS amp FIRMWARE SETTING VNS Series Board can support the BIOS and harness settings for the Optrex TFTLCD models as follows 11 1 TTL Mode
15. video mode Video Composite or S Video Press MENU again to save settings e e Use DOWN or UP to select PICTURE menu or press MENU again to exit the OSD main menu January 23 2004 Page 21 of 26 VNS22 Series User s Manual Revision 1 1 Optrex America Ine 5 4 OSD Lamp Indication Complies with VESA DPMS Requirements Max Power Mode HSYNC VSYNC Video Signal LED Indication Consume Power On Active Active Active Panel Inverter Dependent No Signal In Active Active Blank Green Always on Panel Inverter Dependent DPMS Active Inactive Blank Panel Inverter Dependent Standby Blank Red Always on Max 3W 6 FRAME FREQUENCY SETTING The VNS Series TFT controller board is designed to operate up to a 75Hz refresh rate Refer to the LCD panel specification specific pixel frequency dot clock for the native mode refresh rate 7 APPLICABLE TIMING Resolution Refresh Horizontal Pixel Freq Standard type 60Hz 31 5KHz 25 175MHz Industry Standard 640x480 72Hz 37 9KHz 31 500MHz VESA standard 75Hz 37 5KHz 31 500MHz VESA standard 60Hz 37 9KHz 40 000MHz VESA guideline 800x600 72Hz 48 1KHz 50 000MHz VESA standard 75Hz 46 9KHz 49 500MHz VESA standard 60Hz 48 4KHz 65 000MHz VESA guideline 1024x768 70Hz 56 5KHz 75 000MHz VESA standard 75Hz 60 0KHz 78 750MHz VESA standard January 23 2004 Page 22 of 26 VNS22 Series User s Ma
Download Pdf Manuals
Related Search
Related Contents
BN59-01091A-02Ita 2012 - Accueil SIGMA - Université de Toulouse 取扱説明書 - SOOKI Samsung NP-Q1B Manuel de l'utilisateur Crop Module: Peas ( ) - Red Tractor Assurance PDF R-501 User Manual Kingston Brass HFS1978ACL Installation Guide Roth MA AuraModul Ex 12 kW Philips VR750 User's Manual Lucent AT&T 1810 Corded Phone (23118) Copyright © All rights reserved.
Failed to retrieve file