All STAINLESS STEEL GAS BBQ GRILL USER`S MANUAL
Contents
1. PAGE 23 TROUBLE SHOOTING AE TE PROA pAGE25 FOOD SAFETY TT cn PAGE 26 GRILL STORAGE PAGE 26 aa ws o SS o EE SS SE EE ER Se Thank you for your purchase of our All Stainless Steel BBQ Gas Grill We sincerely wish you will enjoy using our fine products Please read this User s Manual in its entirety before using the grill Please contact our customer service at 888 287 0 735 if you have any questions Please read this Users Manual carefully Failure to follow the provided instruction can result in seriously bodily injury and or property damage IMPORTANT This grill is intended for outdoor use only and is not intended to be installed in or on recreational vehicles or boats NOTE TO INSTALLER Leave this Users Manual with the customer after delivery and or installation NOTE TO CONSUMER Leave this User s Manual in a convenient place for future reference The symbols listed here are being used through out this Users Manual Please pay special attention to them The meaning of each of the symbols Is listed here 7 A DANGER this symbol indicates an imminently hazardous situation which will result in death or serious bodily injury if not properly followed A WARNING this symbol indicates a warning of potential serious bodily injury if the instructions are not strictly followed Please be sure to read and follow all these me2. Tools Required s 2 Philips head screwdriver not provided s Hexagon Allen wrench provided The following hardware kit is provided and packed in rotisserie motor carton Truss head screw N Ee With Split lock And Gasket EK pcs Truss head screw With Split lock And Gasket Hexagon wrench BBO hooks z Take out main body Wa Se Xx N lt w EE 1 a EEN ARE i A w E SS re SON sss SERS EE EEE EE EE j s s s ss s s so 5 STEP Il z Take out left side shelf from carton z Use two 1 4 20x1 2 screws to attach left side shelf from inside of the firebox and use three same screws to attach it from outside of firebox z Use four 1 4 20x1 2 screws to attach push bar on left side shelf z Use two 1 4 20x1 2 screws to install motor bracket on left side shelf z Take out four S style BBQ tool hooks from the hardware bag then hang on the edge of the left side shelf Ps A tl RE a ST NSS N AAA A STEP lll inner slides A push drawer in evenly and slowly on both sides and repeat the steps EES H z g gt i i i t lt i VA Ne ee ae me A ie ca sed DOS SN N SSS lt lt gt SN NF NAL z Remove the left side shelf drawer from inside grill cabinet z Pull out the two dra
3. 1 Yellow flame with burning smell 2 Temperature wont rise 3 Heats unevenly 4 Burners make popping noises s BEFORE CALLING FOR SERVICE Please check the following problems solutions before contact our service center PROBLEMS POSSIBLE CAUSE SOLUTIONS Electrode deposited with lise clean swab and alcohol to clean cooking residues Electrode damaged Replace SSCS Electrode wires are loose Reconnect or replace with new electrode I or a off EE edil WIFeS Wire is shorting Replace with new electrode ET with wires Open the LP tank valve Replace LP tank valve Gas flow is not smooth Clear burner tubes Incorrect assembly Burner won t light after turning and pushing the knobs Burner cant light by match Re assemble between burner and valve Call our customer service center at po0 20 7 07 35 Gas hose bent or kinked Smooth out the hose u Burner or orifice blocked Clear blockage Cal ihe ges dealer Grill not Ee Preheat the grill far 15 minutes Cut off fat before grilling Flare up Yellow or orange Incomplete combustion flame with gas odor P Low heat with knob in HI position Tremp toohigh a O OO a Flame iting Too Wigh ofa gas pressure Calthe gas deae UUO O Grease accumulated in Turn off knobs and LP tank valve Leave lid open food Grease fire ia HEDE and let fire burn out Clean the
4. Chino CA 91710 TA AE MT o ll PRODUCT REGISTRATION First Name Last Name Address City State Zip Code Email Address Phone Product Model Date of Purchase Retail Store Location of Purchase Please rate the importance of each feature 1 least important 10 most important Quality Price Size Capacity Cooking rea Appearance Other What other brands did you seriously consider before making this purchase DCS_ CharBroil_ Brinkman Members Mark Lynx Other Did not consider other brands _ How did you hear about our product Magazine Ad Catalog Salesperson Word of Mouth Internet_ Store Display Other _ Marital Status Single _ Married _ Household Income Below 50 000 50 000 150 000_ 150 000 _ Education High School College Graduate School Primary Residence Own Rent Comments Suggestions
5. ns 0 O 43 non Q OD 0 O G iem N Dd AE Mrs des O y O N es O O Y mm O a a N 0 0 O es v O O a D y dy AE prevent the hose from lifting up and touching the hot firebox me rumu es 3 1 mad lator please make sure to put regulator hose through U FEE RENE ERG Ri N ing regu i Ny lt a EE i SEs Sore Nay N NIN poet H SO NAAA if replac shape bracket Note SEN i ONLY USE THE REGULATOR AND HOSE ASSEMBLY PROVIDED WITH THIS GRILL REPLACEMENT PRESSURE REGULATORS AND HOSE ASSEMBLIES MUST BE THOSE SUPPLIED BY THE MANUFACTURER This is a LP Liguefied Petroleum Gas configured grill Do not attempt to use a natural gas supply unless the grill has been reconfigured for natural gas use The installation of this appliance must conform with local codes or in the absence of local codes with either the National Fuel Gas Code ANSI 2223 1 or CAN CGA B149 2 Propane Installation Code LP TANK REQUIREMENTS THE LP TANK USED WITH YOUR GRILL MUST MEET THE FOLLOWING 1 Measurement 12 30 5cm Diameter X 18 45 7cm Tall 2 Maximum Capacity 20lbs 9Kg 3 Constructed and marked in accordance with the specification for LP gas cylinders of the U S Department of Transportation DOT or the National Standard of Canada CAN CSA B339 Cylinders Spheres and Tubes for the Transportation of Dan
6. see TROUBLESHOOTING if any abnormal status found MAINTENANCE CONTINUED 4 Call our after service center at 888 287 0735 for warranty replacement parts CLEANING 1 STAINLESS STEEL CLEANING The grill is made of stainless steel There are many different stainless steel cleaners available Always use the mildest cleaning procedure first scrubbing in the direction of the grain To touch up noticeable scratches sand very lightly with dry 100 grit emery papers in the direction of the grain Specks of grease can gather on the surfaces of the stainless steel and bake onto the surface and give the appearance of rust Use an abrasive pad in conjunction with a stainless steel cleaner to remove VERY IMPORTANT DO NOT USE ACID DETERGENT AND OR ANTIRUST TO CLEAN THE CONTROL PANEL WITH PRINTING SUCH STRONG x CLEANSER MAY CLEAN OFF THE PRINTING 2 COOKING AREA CLEANING The easiest way to clean the grill is to clean immediately after turning off the flame when cooking is completed Wear a barbeque mitt to protect your hand from the heat and steam Dip a brass bristle barbeque brush in tap water and scrub the hot grill Dip the brush frequently in the water Steam created as water contacts the hot grill assists the cleaning process by softening any food particles The food particles will fall and burn Never immerse a hot part in water 3 GRILL BURNER CLEANING Be sure the tank valve and the
7. 0735 261 888 EER EE E E PG 50506SRLA CUSTOMER SERVICE ME Z ad ee ME id ve SERE MODEL NUMBER ml lt lt lt a LL N ml OT O O CO OO o N lt O al LL LL N N N LL ad lt lt L N lt Model Number PG 50506SRLA PermaSteel All Stainless Steel BBQ Grill We warrant to the original consumer purchaser Purchaser of the PermaSteel All Stainless Steel BBQ Grill Product that each Product shall be free from defects in workmanship and materials for a period of the years listed below from the date of original purchase Our obligation under this warranty shall be limited to repair or replacement of or adequate compensation for the Product at the option of us during the warranty period Our liability shall not extend beyond repair or replacement or the cost equivalent thereto This warranty excludes normal wear and tear of the Product and its parts or components and any damage arising from any of the following negligent use or misuse of the Product use contrary to this Users Manual or alteration by any one other than us The warranty period of the years listed below shall not be extended or renewed by the repair or replacement of or compensation for the Product If your Product is defective or otherwise requires service or parts please first call PermasSteel Customer Service toll free at 888 287
8. are sitting properly on orifices Knobs turn freely The regulator amp hose connected to grill are provided by the manufacturer Pre set for 11 0 water column Unit tested and free of leaks BEFORE LIGHTING Inspect the gas supply hose before turning the gas ON If there is evidence of cuts wear or abrasion it must be replaced before use The replacement hose assembly must be that specified by the manufacturer VERY IMPORTANT TO LIGHT MAIN AND SIDE BURNERS OF THE GRILL 1 Read instructions before lighting 2 Turn all knobs to OFF then open the LP tank valve Always keep your face and body as far from the grill as possible when lighting 3 Open lid during lighting 4 Push and turn any control knob slowly to HI position The built in igniter will click and spark simultaneously to light the pilot and burner in sequence Turn the control knob to OFF IMMEDIATELY if the burner does not light within 5 seconds Wait 5 minutes for gas to dispel then repeat the lighting procedure a 9 Follow match lighting instructions if burner can t be lit after repeating 3 4 times o Es R S TO LIGHT THE MAIN AND SIDE BURNERS BY MATCH AS THE FOLLOWING FIGURE SHOWS If the burner will not light after several attempts then the burner can be match lit Tools Lighting rod hanging behind the right door Usage 1 Read instructions before lighting 2 Open the lid during lighting 3 Simply place a ligh
9. down the button The built in igniter will click and spark simultaneously to light the burner once burner lights Keep pressing safety valve button for 15 seconds to allow the safety valve to open Turn the control knob to OFF and release the button IMMEDIATELY if the burner does not light within 5 seconds Wait 5 minutes for gas to dispel then repeat the lighting procedure TO LIGHT URNER BY MATCH 1 Read instructions before lighting 2 Open the lid during lighting 3 Push and turn the rear burner knobs slowly to HI position then release 4 Push down the safety valve switch button with right hand and hold on light by match with left hand Make sure the burner lights and stays lighted CAUTION z Clean the grill often A grease fire that may damage the grill may occur if the grill has not been cleaned frequently z NEVER leave the grill unattended while using z Do not use water to extinguish the grease fire it may cause body injury Turn knobs off and LP tank off in case grease fire occurs z Grease fire can t be put out by closing the lid Turn off knobs and LP tank IMMEDIATELY if any grease fire occurs WARNING For your safety Keep grill area clear and free from any flammable material NEVER let children operate the grill or play near the grill This grill is for outdoor use ONLY NEVER use in a enclosed area such as a carport porch covered patio garage or under a surface t
10. flame 4 Make a soap solution with one part liquid detergent and another part water Prepare a spray bottle brush or rag to apply the solution to the connections For the initial leak test make sure the LP cylinder is full a 5 Grill must be leak tested outdoors in a well ventilated area away from ignition sources such as gas fired or electrical appliances and flammable materials 6 Keep grill away from open flames and or sparks while testing RRS SS ae 524 TO TEST 1 Make sure all control knobs are in the OFF position 2 Make sure the regulator is connected to the LP tank tightly 3 Completely open LP tank valve by turning counter clockwise If you hear a POP sound turn gas off IMMEDIATELY as it indicates a heavy leak at the connection Call your gas dealer or fire department 4 Check every connection from the LP tank up to and including the connection to the manifold pipe assembly the pipe that goes to the burner by brushing or spraying the soapy solution on the connections 5 If soap bubbles appear there is a leak Turn off LP tank valve IMMEDIATELY and retighten connections Open LP tank valve again and recheck 6 If leaks cannot be stopped DO NOT ATTEMPT TO REPAIR Call our service center at 888 28 0735 for help Always close the LP tank valve after leak testing by turning clockwise Only those parts recommended by the manufacturer should be used on the grill Substitution wi
11. grill after cooling 1 Always follow the following tips to enjoy safe and healthy outdoor grilling 2 Always use hot soapy water to wash hands surfaces amp utensils after processing raw meat 3 Always separate raw meat from cooked foods to avoid cross contamination 4 Always use clean utensils to handle the food 5 Always cook the meat thoroughly to kill germs Use a thermometer to inspect the inner temp of the meat if necessary 6 Place the cooked foods and leftovers promptly into the refrigerator when done eating VERY IMPORTANT DO NOT LEAVE THE GRILL UNATTENDED WHILE COOKING x GRILL STORAGE 1 Clean the grill 2 Store the grill in a well ventilated dry outdoor area Keep out of the reach of a do children when LP tank is connected to the grill a 3 Store the grill in dry indoors ONLY after the LP tank is turned off and removed o The LP tank must be stored outdoors out of the reach of children NEVER store the tank in a building garage or any other enclosed area 4 Put on the supplied vinyl cover Lo Va as o IEKE E AAE o 26 e Thank you for purchasing the PermaSteel In order to register your product to receive streamlined customer service please fill out the following Product Registration form and 1 fax the form and a copy of your receipt to FAX 909 287 0733 or 2 mail the form and a copy of your receipt to PermaSteel Inc 14125 Telephone Avenue 8
12. knobs are in the OFF position Make sure the grill Is cool Clean the exterior of the burner with a wire brush Clear stubborn scale with a metal scraper Clear any clogged ports with a straightened paper clip Never use a wooden toothpick as it may break off and clog the port Please note that if Insects or other obstructions are blocking the flow of gas through the burner you will need to call our customer service line VERY IMPORTANT The orifice of the valve must be located in the center of the burner section after removal and cleaning Otherwise it may cause serious bodily injury and property damage Swing the burner slightly after replacing to check whether it has been installed properly YES SS a RRS EE EE SEER AE EES SR ESAS SS s SS SS OS a o o o o ED REEN Saas ONAN PRESS So EE O s 4 GREASE TRAY CLEANING 7 p x The grease tray should be emptied and wiped down periodically and washed x in a mild detergent and warm water solution A small amount of sand may be placed in bottom of the grease tray to absorb the grease EE EE AS EE N es AAA z SPIDER AND INSECT WARNING Spiders and insects can nest in the burners after storing These nests can cause fires a inside the tube or beneath the grill This is a very dangerous condition So always clean the burners before use WHEN TO LOOK FOR SPIDERS Inspect the burners at least once a year or immediately if any of the following conditions occur
13. 0735 between 8 00 a m and 5 00 p m PST Please tell us which model you purchased the date of purchase and the problem with your Product We will x use our very best efforts to honor this warranty and repair replace or compensate you for your O Product through your original place of purchase A copy of your original purchase receipt must do accompany your service request o Component Warranty Period Burners 1 Year Stainless Steel Flame Tamer 1 Year Stainiess Steel Cooking Grids 1 Year Valves 1 Year ee O Frame Housing Cart Control Panel o Igniter and Related Parts 1 Year All Stainless Steel Parts 1 Year LIMITATION OF REMEDIES AND LIABILITY We shall not be liable for any incidental or consequential damages for breach of any express or implied warranty on its Product Except to the extent prohibited by applicable law any implied warranty or merchantability or fitness for a particular purpose on this Product shall be limited to the duration of the above warranty Neither us nor anyone else who has been involved in the creation production or delivery of the Product shall be liable for damages of any type including but not limited to any lost profits lost savings loss of anticipated benefits or other incidental or consequential damages which may arise out of the purchase use or inability to use the Product whether arising out of contract negligence strict tort or under any warranty or otherwise even i
14. LP gas supplier or the fire department AX DANGER a z NEVER store a spare LP tank under or near grill or in an enclosed area z NEVER fill the tank beyond 80 full An overfilled spare LP tank is dangerous because surplus gas may leak from safety relief valve The safety relief valve on a LP tank could activate to release gas and cause a fire z The spare LP tank must have safety caps installed on the LP tank outlet z f any gas leaks are found on the spare LP tank immediately step away from the grill and call the fire department VERY IMPORTANT DISCONNECT THE TANK WHEN THIS GRILL IS NOT IN USE To disconnect LP gas tank 1 Turn all the knobs off 2 Turn the tank valve off fully turn clockwise to stop 3 Detach the regulator assembly from tank valve by turning the quick coupling nut counterclockwise 4 Install the protective cap back onto the LP tank valve a GENERAL Although all gas connections on the grill are leak tested at the factory prior to shipment a complete gas tightness check must be performed at the installation site due to possible mishandling in shipment or excessive pressure unknowingly being applied to the unit Periodically check the whole system for leaks or immediately check if the smell of gas is detected BEFORE TESTING 1 Make sure that all packing material is removed from the grill including the burner tie down straps 2 Do not smoke while leak testing 3 Never leak test with an open
15. e it has proper external male threads type connection per ANSIZ21 81 3 Make sure all burner knobs are in their off position 4 Remove the protective cap from LP tank valve Always use cap and strap supplied with valve 5 Inspect valve connection port and regulator assembly Look for any damage or o debris Remove any debris Inspect hose for damage Never attempt to use x damaged or plugged equipment Contact your local LP gas dealer for repair 6 When connecting regulator assembly to the valve hand tighten nut clockwise to a positive stop Do not use a wrench to tighten Use of a wrench may damage quick coupling nut and result in a hazardous condition As figure shown below OPD HAND WHEEL be 1 wasi 7 Open tank valve fully counterclockwise Use a soapy water solution to check all connections for leaks before attempting to light grill If a leak is found turn tank valve off and do not use grill until a local L P gas dealer can make repairs AN WARNING Never insert any foreign objects into the valve outlet It may damage the valve and cause leak leaking gas may result in fire explosion heavy body injury or even death Do not connect this grill to the self contained LP gas system of a motor home or camper trailer Do not use this grill until leak tested z STOP and call the fire department if any leaks are detected If you cannot stop a gas leak close the LP tank valve IMMEDIATELY call
16. en not in use z This grill is safety certified for use in the United States and Canada only Never modify to use in other places Modification may cause serious bodily injury or o property damage PermaSteel is not responsible for any modifications and all warranties will be void A WARNING FOR YOUR SAFETY PLEASE READ THIS SECTION FIRST If you smell gas Shut off gas to the grill Extinguish any open flames immediately Open the grill lid If the odor persists please call your gas supplier or your fire department immediately s Do not store or use gasoline or other flammable items in the vicinity of this grill s Any LP cylinder that is not connected for use should not be stored in the vicinity of this grill x A E A Tay 6 iid Handle Se 2 47 BackPanel A 8 Rotisserie KE 1 49 Rear Burner Gover 1 9 Hnge SideBumertia 1 50 Thermocouple Cover 1 x x x ro Bracket C Side Bumer 1 60 Flametamers 57 23 kns ele Me A 25 Side Burner Hose 1 66 LeftSide Sheff 27 Rear Bumer Valve 68 LetSide Drawer 28 Safety Valve amp Buttom 1 69 Snap Close 37 Slicing Bars e 78 ignitorRod Ji 39 Bottom Panel 1 80 Upper Door Hinge Bracket 40 Right Drawer Transoms 2 Bi Reguiator a a EA EE a O Se WWW a Ms 5 Z yy af oe EE ES i O PLEASE READ AND FOLLOW THE INSTRUCTIONS CAREFULLY STEP BY STEP
17. f you have been advised of the possibility of such damage or any other claim by any other party Our liability for any breach of warranty shall be limited to repair or replacement of the defective part or parts as described above Some states do not allow the exclusion or limitation of incidental or consequential damages so the above limitation or exclusion may not apply to you The above LU warranty gives you specific legal rights and you may have other rights which vary from state to o state Notice PermaSteel provides the PVC cover for your convenience only We do not provide warranty for PVC cover o i BEFORE YOU BEGIN x MESSAGE TO OUR USERS __ _ coco PAGE 1 SAFETY SYMBOLS __ PAGE 1 INSTALLATION 8 SAFETY PRECAUTIONS esse PAGE 2 PROPANE 8 GAS WARNING PAGE 2 ASSEMBLY PARTS PAGE 3 STEP art AGES GTED 2456862225524 EERS EA AGE G SIE Dl A A PAGE 4 SIFON alta a ASES SEE BA MA PA ME EA IE PAGE 9 STEP VI N EE N EE EN PAGE A te lt lt SS lt lt o SS ES SS STEPV ocetne PAGE 12 BAY RAS POST ASSEMBLY GAS CONNECTION PAGE 14 LEAK TESTING s PAGE 17 FINAL INSTALLATION CHECK LIST PAGE 18 GRILL LIGHTING INSTRUCTION _ _ _ PAGE 19 OPERATING INSTRUCTION 77 TT TT TT TT Tm PAGE 21 CARE 8 MAINTENANCE
18. gerous Goods See LP tank collar for marking 4 Is arranged for vapor withdrawal 5 Includes a collar to protect the tank valve 6 Has no dents or rust A dented or rusty L P tank may be hazardous and should be checked by your supplier Provides a shut ff valve terminating in an LP gas tank valve outlet specified as applicable for connection type QCC1 in the standard for compressed gas tank valve outlet and inlet connection ANSI CGA V 1 LP TANK VALVE USED MUST MEET THE FOLLOWING 1 Have type outlet compatible with regulator provided 2 Have safety relief valve 3 UL listed Overfill Protection Device OPD This OPD safety feature is identified by a unique triangular hand wheel Only use tanks equipped with this type of valve As the figure shown on the next page FORYOURSAFETY ol x Ensure that the black plastic grommets of the regulator provided are in place and that the hose does not come Into contact with the heat shield or the grill head CONNECT THE REGULATOR TO THE LP TANK VERY IMPORTANT a THE REGULATOR SHALL NOT BE IN A LOCATION THAT WILL ATTAIN A TEMPERATURE ABOVE 140 60 C THE REGULATOR SHALL INCORPORATE A PRESSURE RELIEF VALVE OR OVERPRESSURE DEVICE THE INLET OF THE PRESSURE REGULATOR SHALL BE FITTED TO CONNECT THE TYPE CONNECTION OF THE TANK VALVE PER ANSIZ21 81 1 Make sure tank valve is in its full off position turn clockwise to stop 2 Check tank valve to assur
19. hat can catch fire Do not block the ventilation holes in the four sides of the grill cart it may affect the combustion performance of the burner due to insufficient air a z Use the grill at least 36 away from any wall or surface 120 away from objects that 9 may spark and ignite gas i e live electrical appliances pilot lights of water heaters Do not use this grill on or under wood balconies z This grill is designed to use only LP gas DO NOT use lava rock briquets charcoal on it z NEVER light the burner with the lid closed Non ignited gas accumulated inside a closed grill may cause explosions Check the burner flames periodically Turn off the gas supply when the grill is not in use x Always turn off the LP tank completely and detach from the grill before moving x x EEE EE 21 SOE TEE EEE EEE UO OOOO ORO ROO a a TOTAL GAS CONSUMPTION Total gas consumption per hour of PG 50506SRLA grill with all burners on HI Main burners 60 000 Btu hr Side burner 12 000 Btu hr Rear burner 12 000 Btu hr Total 84 000 Btu hr GENERAL USE OF THE GRILL The grill burners encompass the entire cooking area and are side ported to minimize blockage from falling grease and debris Above the burners are stainless steel radiated The igniter knobs are located on the valve panel Follow the lighting instructions printed on the control panel USING THE GRILL Grilling requires high heat for seari
20. he grounding prong Keep any electrical supply cords and the fuel supply hose away from any heated surfaces Remove and store the motor in a dry place when not use USING ROTISSERIE KIT 1 Take off the rotisserie kit from the grill 2 Slide off the left fork and load the meat or poultry onto the rod 3 Restore the left fork put two forks into the meat or poultry as far as possible Make sure the meat or poultry is located in the middle of the rod Screw the wing nuts of the fork as tight as possible 4 Wrap the food with butchers string never use nylon or plastic string to secure any loose portions if necessary 5 Restore the rotisserie kit into the motor ROTISSERIE TIPS 1 If larger cuts of meat are being grilled the rod may flex This is normal 2 Remove the cooking grids for larger cuts of meat if the meat scrapes on the cooking grids during rotation MAINTENANCE 1 Keep the grill area clear and free from combustible materials gasoline and other flammable vapors and liquids 2 Keep the holes in the three sides of the cart clear and free from debris thus ensure the flow of combustion and ventilation air is unobstructed 3 Visually check burner flames as following Remove cooking grids and flame tamers Light burners Turn knobs from HI to LO check the flame status the flame in LO position should be smaller than in HI position as figure shown below Always check flame before each use
21. ll void the warranty Do not use the grill until all connections have Ll been checked and do not leak DOU DUULUUL O SAFETY TIPS 1 ALWAYS CHECK FOR LEAKS AFTER EVERY LP TANK CHANGE 2 ALWAYS CHECK FOR LEAKS BEFORE EACH USE 3 USE LONG BBQ TOOL TO AVOID BURNS 4 CHECK ALL GAS SUPPLY FITTINGS FOR LEAKS BEFORE EACH USE IT IS HANDY TO KEEP A SPRAY BOTTLE OF SOAPY WATER NEAR THE SHUT OFF VALVE OF THE GAS SUPPLY LINE SPRAY ALL THE FITTINGS BUBBLES INDICATE LEAKS 5 DISCONNECTED L P CYLINDERS MUST HAVE THREADED VALVE PLUGS TIGHTLY INSTALLED AND MUST NOT BE STORED IN A BUILDING GARAGE OR ANY OTHER ENCLOSED AREAS 6 TURN OFF ALL CONTROL KNOBS AND LP TANK VALVE WHEN THE GRILL IS NOT IN USE 7 IF THE APPLIANCE IS STORED INDOORS THE LP TANK MUST BE DISCONNECTED AND REMOVED FROM THE GRILL 8 LP TANKS MUST BE STORED OUTDOORS IN A WELL VENTILATED AREA DISCONNECTED LP TANKS IN STORAGE OR BEING TRANSPORTED MUST HAVE A SAFETY CAP 9 NEVER LEAVE A LP TANK IN A RECREATIONAL VEHICLE OR BOAT WHICH MAY BECOME OVERHEATED BY THE SUN 10 DO NOT STORE LP TANK IN OR NEAR AN AREA WHERE CHILDREN PLAY 11 FOR ANY OTHER PROBLEMS SEE TROUBLESHOOTING OR CONTACT OUR SERVICE CENTER AT 888 287 0735 Bs ae iaon o At least 36 clearance maintained from combustible constructions to the sides and back of this grill There is no combustible construction material over the grill All internal packaging removed Burners
22. ng and proper browning Most foods are cooked at the HI heat setting for the entire cooking time However when grilling large pieces of meat or poultry it may be necessary to turn the heat to a lower setting after the initial browning This cooks the food through without burning the outside Foods cooked for a long time or basted with a sugary marinade may need a lower heat setting near the end of the cooking time 1 Make sure the grill has been leak tested and is properly located 2 Remove any packing material 3 Light the grill burners using the instructions in this manual 4 Turn the control knob to HI and preheat the grill for 15 minutes 5 The grill lid is to be closed during the appliance preheat period 6 Place the food on the grill and cook to the desired doneness Adjust heat setting if necessary The control knob may be set to any position between HI and LO The grill is designed to grill efficiently without the use of lava rocks or briquettes of any kind Heat is radiated by the stainless steel flame tamers under the stainless steel cooking grids 8 The hot grill sears the food sealing in the juices The longer the preheat the faster the meat browns ELECTRICAL GROUNDING INSTRUCTIONS This grill is equipped with a three prong grounding plug on rotisserie motor for your protection against shock it should be plugged directly into a properly grounded three prong receptacle Do not cut or remove t
23. ssages carefully A CAUTION this symbol indicates a potentially hazardous situation which may result in minor or moderate bodily injury if the instructions are not properly followed Some parts of this grill may have sharp edges Please wear suitable protective gloves WARNING READ THIS SECTION FIRST BEFORE INSTALLING THE GRILL z This grill is designed to use LP gas only Please use the grill with the regulator supplied by PermaSteel on The installation of this appliance must conform with local codes or in the absence u of local codes with either the National Fuel Gas Code ANSI Z223 1 or a u CAN CGA B149 1 Natural Gas Installation Code or CAN CGA B149 2 Propane Installation Code a The LP gas supply cylinder is to be constructed and marked in accordance with the 9 O specifications for LP gas cylinders of the U S Department of Transportation DOT or the National Standard of Canada CAN CSA B339 Cylinders a Spheres and Tubes for the Transportation of Dangerous Goods n f an external electrical source is utilized the outdoor cooking gas appliance when installed must be electrically grounded in accordance with local codes or in the absence of local codes with the National Electrical Code ANSI NFPA 70 1990 or the Canadian Electrical Code CSA C22 1 Keep the power cord of the motor away from the hot surfaces of the grill while in use Remove and store the motor in a dry place wh
24. ted match between the coils on the end of the lighting rod and hold next to the burner to ignite 4 Push and turn the knob to HI position make sure the burner lights and stays lighted 5 Repeat 3 4 to light other burners 6 Keep a spray bottle of soapy water near the gas supply valve and check the connections before each use Do not light the grill if odor of gas is present call out service center at 888 287 0735 262 FLAME CHARACTERISTICS 1 Check for proper burner flame characteristics Each burner is adjusted prior to shipment however variations in the local gas supply may take subtle necessary adjustments 2 Burner flames should be blue and stable with small yellow tips no excessive noise or flames lifting of the burners If any of these conditions exist call our customer service line If the flame is yellow it indicates insufficient air If the flame is noisy and tends to lift away from the burner it indicates too much air 3 Small yellow tips are ok TO LIGHT THE REAR BURNER OF THE GRILL 1 Read instructions before lighting 2 Turn all knobs to OFF then open the LP tank valve Always keep your face and body as far from the grill as possible when lighting 3 Open lid during lighting 4 Push down the safety valve switch button and hold on with right hand allowing the gas to reach the burner 5 Push and turn rear burner knob slowly to HI position with left hand 2 seconds later than push
25. valve steam to go through opening on front of side burner control panel UNT NN O IU ie EE III ay sea eT N O ci AUS Ee ee ED DIN Eg WWW O CA EE MEE NG i EN Ee A ES UU POL oe oe cA ATT N STEP V continued Attach and secure side gas valve to control panel using the M4 6 screws Slightly insert Side Burner onto tip of gas valve make sure its centered Replace and tighten the four screws on brackets A amp C Attach igniter wire with red sleeve to valve electrode Place and press control knob onto valve steam and tighten the setscrew of knob e CN II HNN i be RR STEP VI Remove rotisserie rod from back panel packing foam take out handle prongs counter balance and shaft collar from rotisserie carton Tread key washers and counter balance onto treaded end of rotisserie rod next tread handle and tighten slide shaft collar through other side of rod followed by the two prongs forks should be pointing towards each other tighten thumb screws on shaft collar and prongs Remove packing material from flame tamers cooking grids and warming rack then place them in the proper positions shown below STEP VII is will keep lock the caster brakes th ion d locat ire in the desi the grill unit in place for safe operation IS In When the grill de 2 1 O aar O Z Pad N O A y dy OD N O S
26. wers inner slides A attached to left side shelf all the way out Insert the drawer into left shelf make sure the outer slides B insert into the Notice push drawer in and out until it goes in smoothly and will not fall of slides when pulled out if not please re insert outer slides B into inner slides A B uwema w e aae aae KSN NON EE E STEP IV z Take out right side shelf from carton z Use two 1 4 20x1 2 screws to attach right side shelf from inside of the firebox and use three same screws to attach it from outside of firebox z Use three 5 32 32x1 2 screws to attach right side angle iron to side shelf and also use two same screws to attach it to firebox from outside z Use four 1 4 20x1 2 screws to attach push bar to right side shelf AT siii LIL E zs ZZ re Z ZZ Z ERIS AS op i EE ZZ Take out side burner hose with attached side burner valve from inside grill cabinet through square opening of right side panel Remove the packing materials Use the provided hexagon wrench Allen to loosen don t remove the setscrew on the control knob and pull out the knob Remove the two M4 6 screws from front of side burner valve Remove the four screws on side burner bracket A amp C which attach side burner slide side burner back to allow side valve to be mounted From underneath side shelf place side burner
Download Pdf Manuals
Related Search