SN66T095GB-EN - Devicemanuals
Contents
1. Folding spikes Small accessories holder Adjusting the height of thie basketb eode e cec e RR Detergent Adding detergenty Combination detergent Kon Overview of programmes Programme selection Information for test institutes Additional options Express WaschPlus SpeedPerfectPlus VarioSpeedPlus Half load s do oh ers HygienePlus Intensive 20 High gloss drying Energy Save EY Operating the appliance Programme Aqua Zeolith drying Switching on the appliance Optical display while the programme is running Remaining running time display Timer programming End of programme Automatic switch off interior Switching off the appliance en 20 23 en Intended use Interrupting the programme 24 Terminating the programme 25 Changing the programme 25 Intensive drying 25 Cleaning and maintenance 25 Overall condition of the machine 26 Special salt and rinse aid 26 Filters 24 Geek ve Ra Ee EAS Es 26 Spray AMS ERR 27 Fault what to do 27 Waste water pump 28 Fault table sesso da RR Rs 29 Customer service 32. Appliance height 86 5 cm Top basket Bottom basket Pull out the top basket 22 out lower the basket press in the left and then the right lever on the outside of the basket In doing so hold the sides of the basket along the upper edge to prevent it from suddenly dropping N 3 To raise the basket hold the basket on the sides of the upper edge and lift it up 4 Before re inserting the basket again ensure that it is at the same height on both sides Otherwise the appliance door cannot be closed and the upper spray arm will not be connected to the water circuit Detergent You can use tablets as well as powder or liquid detergents for dishwashers but never use washing up liquid The dosage can be individually adjusted with powder or a liquid detergent according to the degree of soiling Tablets contain an adequately large amount of active ingredients for all cleaning tasks Modern powerful detergents predominantly use a low alkaline formulation with phosphate and enzymes Phosphates bond the lime in the water Enzymes break down starch and remove protein Phosphate free detergents are less frequent These have a slightly weaker lime bonding capacity and require a higher dosage To remove coloured stains e g tea tomato sauce oxygen based bleaching agents are usually used Note To ensure a good washing result always follow the instructions
3. orrectly ntensely sensors therefore decide on nce be in corner quately t and left ed by utensils and does not open fully herefore Detergent dispenser cover blocked by the tablet Tablets used in the quick or short prog ramme Dissolving time of the detergent t reached in the selected is short programme Washing performance are reduce a prolonged storage time or detergent is very lumpy fect and dissolving d after Remedial action Arrange utensils with adequate clearance between them ensuring that the spray jets can reach the surface of the utensils Prevent contact points Arrange utensils so that the spray arm can rotate without obstruction Clean the spray arm nozzles See Cleaning and maintenance Clean filters see Cleaning and maintenance Insert and engage filters correctly Select a more intensive rinse programme Do not prerinse utensils Remove only large n e food remnants Recommended programme Eco 50 or Intensive Do not place hollow receptacles too obliquely and do not place in the corner area Set top basket to same height using side levers Detergent dispenser cover must not be obstructed by utensils Do not place utensils or fragrance dispenser in the tablet collecting tray Tablet must be inserted flat and not upright Dissolving time of tablets too long for a quick or short pr
4. Dishwasher SN SX siemens home com welcome en Dishwasher Operating instructions Register your product online Table of contents Intended use 4 Safety instructions 4 Before you switch ON the appliance 4 Delivery cte of p eER TD 5 e TED e ERR I 5 In daily S6 4 mee Be toh p 6 Door IOC ga vids deoa vina 6 Damage 6 Disposal d xxi ve d Ra 6 Protection of the environment 8 8 Old appliances 8 Getting to know your appliance 9 Control panel 9 Appliance interior 9 Overview of menu 6 5 9 Water softening system Special salt 10 Setting RN eese 10 Water hardness table 10 Using special 11 Detergents with salt component 11 Switching off water softening system 11 Rinseaid 12 Setting amount of rinse aid 12 Switching off rinse aid refill indicator 13 Utensils Accs die LALII 13 Not suitable 13 Glass and utensil damage 13 Loading the dishwasher Unloading the dishwasher Cups glasses PaliS doe t ed pedes Oe idest ct Cutlery drawer
5. 2 Switch on ON OFF switch 1 3 Press the button until Z fis flaching in the timer programming display LZ 4 Press or button until the displayed time corresponds with your requirements 5 Press START button 10 timer programming is activated Operating the appliance en 6 To delete timer programming 8 press the or button until 20 is indicated on the digital display LZ You can change your programme selection at any time until the programme starts 7 Close the door End of programme The end of the programme gt 2 00 displayed on the floor provided the optical display is switched on and is visible The end of the programme is also indicated by an acoustic signal This function can be changed as follows 1 Open the door 2 Switch on ON OFF switch 1 3 Hold down programme button and press START button until is indicated on the digital display 4 Release both buttons The LED for button flashes and the digital display displays the factory setting 5 Press programme button until the factory set value 5 202 is indicated on the digital display 3 To change the setting 1 Press programme button C Each time the button is pressed the set value increases by one level when the value of 2 03 has been reached the display jumps back to 6 00 off 2 Press START button 10 the set value is saved 3 Close the door 23 en Operat
6. AN Warning Risk of cuts When cleaning the waste water pump ensure that you do not injure yourself on pieces of broken glass or pointed implements In this case 1 First always disconnect the appliance from the power supply 2 Take out top basket and bottom basket 30 3 Remove the filters 29 4 Scoop out water use a sponge if required 5 Prise out the white pump cover as illustrated using a spoon Grip the cover on the crosspiece and lift diagonally inwards Remove cover completely 28 6 Check impeller wheel and remove any foreign objects 7 Place cover in the original position and press down until it engages click 8 Install filters 9 baskets Fault table Fault Check water supply display 4 lights up Error code E Z is lit JU Error code E Z 4 is lit Error code E 275 is lit Error code 2 27 1 is lit Cause Supply hose kinked Tap turned off Filter in the water supply blocked Filters are soiled or blocked Waste water hose is blocked or kinked Siphon connection still sealed Cover on the waste water pump loose Waste water pump blocked or cover on the waste water pump is not locked in position Mains voltage too low Tap jammed or calcified Fault what to do en Remedial action nstall supply hose without kinks Turn on the tap Turn on the tap ow rate must be min
7. depending on model Overview of menu The settings can be found in the individual chapters H Water Hardness 4 00 4 07 d Intensive drying duiu dii Rinse aid i 06 Hot water of programme buzzing sound b og m 5 0 ua P Automatic disconnection 2 207 5 Optical display while the programme is running 5 00 5 02 en Water softening system Special salt Water softening system Special salt To ensure good washing results the dishwasher requires soft water i e containing low amounts of lime otherwise white limescale will be deposited on the utensils and inner container Tap water above 1 2 mmol l must be softened The water is softened with special salt regeneration salt in the water softening system of the dishwasher The setting and therefore the required amount of salt depends on the degree of hardness of your tap water see table Setting The amount of salt dispensed can be set from HHG to 7 Salt is not required at the set value Ha 1 Find out about the hardness value of your tap water Your water utility company will help you with this 2 Set value can be found in the water hardness table 3 Open the door 4 Switch on ON OFF switch 1 5 Hold down programme button and press START button until is indicated on the digital display 6 Release both buttons The LED for button flashes and the digital display displa
8. on the detergent packaging If you have further questions we recommend that you contact the detergent manufacturers helpline AN Warning Read and observe the safety information and instructions for use on the packaging for cleaning and rinsing agents Adding detergent 1 If the detergent dispenser is still closed press the lock to open the detergent dispenser Pour detergent into the dry detergent dispenser only insert tablet flat not on its edge Dosage see manufacturer s instructions on the packaging The graduated detergent dispenser helps you add the correct amount of powder or liquid detergent Usually 20 ml 25 ml are adequate for normal soiling If using tablets one tablet is adequate 2 Close the cover on the detergent dispenser by sliding it up until the lock engages without difficulty The detergent dispenser opens automatically at the optimum time depending on the programme The powder or liquid detergent is distributed in the appliance and is dissolved the tablet falls into the tablet collecting tray where it dissolves in doses Detergent en Tip If the utensils are only lightly soiled slightly less than the indicated amount of detergent is usually adequate Suitable detergents and care products can be purchased online via our website or via customer service see back page Combination detergent Apart from conventional detergents Solo a number of products
9. or drying process had not ended yet after program ends before removing utensils Use a proprietary rinse aid Eco products are The eco rinse aid used has a poor drying performance Special properties of plastic Cutlery not arranged properly in the cutlery basket Cutlery not arranged properly much less effective Plastic has a lower heat storage capacity and therefore dries less well Separate cutlery if possible prevent contact points Arrange cutlery properly and separate if in the cutlery drawer Appliance interior wet after No appliance fault rinse cycle possible On account of the Condensation drying principle water droplets are physically induced and required in the container The humidity in the air condenses on the inner walls of the dishwasher drains and is pumped out 31 en Fault what to do Fault Food remnants on the utensils Detergent residue 32 Cause Utensils placed too closely together utensils basket overfilled Spray arm rotation obstructed Spray arm nozzles blocked Filte Filte Uten wea Stub 5129 dirty s 29 inserted inc and or not engaged Rinse programme too weak sils precleaned too i programme seque born soiling cannot completely removed area Top not set to same height rgent dispenser cover Dete bloc Tall narrow receptacles s are not rinsed ade basket on righ
10. regularly clean it with a damp cloth and a little washing up liquid m If the appliance is switched off for a prolonged period leave the door ajar to prevent the formation of an unpleasant odour Never use a steam cleaner to clean your dishwasher The manufacturer is not liable for any consequential damage Regularly wipe the front of the appliance and fascia with a damp cloth water and a little washing up liquid are adequate Do not use sponges with a rough surface or abrasive detergents as these could scratch the surfaces Stainless steel appliances To prevent corrosion avoid using sponge cloths or wash them out thoroughly several times before using for the first time AN Warning Health hazard Never use other domestic detergents e g containing chlorine Special salt and rinse aid Check the refill indicators and If required refill salt and or rinse aid 26 Filters The filters keep large foreign objects in the rinsing water away from the pump These foreign objects may occasionally block the filters The filter system consists of a coarse filter a flat fine filter and a microfilter 1 After each washing cycle check the filters for residue 2 Unscrew filter cylinder as illustrated and take out filter system 3 Remove any residue and clean filters under running water 4 Re install filter system in reverse sequence and ensure that the
11. a programme can be changed is by Cancel programme Reset Cleaning and maintenance en Intensive drying The final rinse uses a higher temperature which improves the drying result The running time may increase slightly Caution if utensils are delicate 1 Open the door 2 Switch on ON OFF switch 1 3 Hold down programme button and press START button until is indicated on the digital display 4 Release both buttons The LED for button flashes and the digital display displays the factory setting 5 Press programme button until the factory set value 2 20 is indicated on the digital display 3 To change the setting 1 Press the button C to switch the Intensive drying on 2 0 or off 2 017 2 Press START button 10 The set value is saved 3 Close the door Cleaning and maintenance A regular inspection and maintenance of your machine will help to prevent faults This saves time and prevents problems 25 en Cleaning and maintenance Overall condition of the machine m Check spray arm for grease and limescale deposits If you find such deposits m Fill detergent dispenser with detergent Start the appliance without utensils in the programme with the highest rinsing temperature Clean the appliance with detergents appliance cleaners which are particularly suitable for use with dishwashers m To ensure that the door seal always remains clean and hygienic
12. agent to the inside of the appliance s door m Even if the rinse aid and or salt refill indicator is lit the rinse programme will run correctly with combined detergents m f sing detergents in a water soluble protective cover Take hold of the cover with dry hands only and put the detergent into an absolutely dry detergent dispenser only otherwise the detergent may stick m f you switch from combined detergents to solo detergents ensure that the water softening system and amount of rinse aid have been set to the correct value Overview of programmes en Overview of programmes The max possible number of programmes is illustrated in this overview The corresponding programmes and their arrangement can be found on the fascia Type of utensils Type of soiling Programme Possible Programme sequence additional options auto pots and pans very adhesive burned i o non sensitive in or dried on food Auto 69 75 in utensils remnants containing sensors 9 and cutlery starch or protein Auto 45 65 n optimised according m to the soiling with the aid Auto 45 65 of sensors part dried common Prerinse mode Clean 50 all Intermediate rinse Eco 50 Final rinse 65 Drying IntensivZone Express Wash D Speed Perfect optimised according sensitive utensils Uo to the soiling with the aid cutlery sligh
13. are offered with additional functions These products contain not only the detergent but also rinse aid and salt replacement substances 3in1 and depending on the combination 4in1 5in1 etc additional components such as glass protection stainless steel cleaner Combination detergents function only up to a specific degree of hardness usually 21 dH Over this limit salt and rinse aid must be added As soon as combined detergents are used the rinse programme is adjusted automatically to ensure the best possible rinsing and drying result 17 en Detergent AN Warning Do not place small parts for washing in the tablet collecting tray 24 this prevents the tablet from dissolving evenly AN Warning If you want to add more utensils after the programme has started do not use the tablet collecting tray as a handle for the upper basket The tablet could already be there and you will touch the partially dissolved tablet 18 Notes m You will obtain optimum rinsing and drying results by using solo detergents and applying salt and rinse aid separately m f programmes are short tablets may not have full cleaning effect due to different dissolving properties and there may even be undissolved detergent residue It is recommended to use washing powder for these programmes m The Intensive programme on some models requires one tab only When using washing powder you can apply some of this cleaning
14. setting are left on the utensils 1 Open the door 2 Switch on ON OFF switch 1 3 Hold down programme button and press START button until is indicated on the digital display 4 Release both buttons The LED for button flashes and the digital display displays the factory setting 5 Press programme button until the factory set value 7 15 is indicated on the digital display To change the setting 1 Press programme button C Each time the button is pressed the set value increases by one level when the value of 115 has been reached the display jumps back to off 2 Press START button 10 The set value is saved 3 Close the door Switching off rinse aid refill indicator If the rinse aid refill indicator 6 is impaired e g when using combined detergents containing rinse aid component it can be switched off m Proceed as described under Setting amount of rinse aid and set the value to 010 The rinse aid refill indicator 6 is now switched off Utensils Not suitable Cutlery and utensils made of wood m Delicate decorative glasses craft and antique utensils These decors are not dishwasher proof Plastic parts not resistant to heat m Copper and tin utensils Utensils which are soiled with ash wax lubricating grease or ink Aluminium and silver parts have a tendency to discolour and fade during the wash cycle Even some types of glass
15. 10 l min hen water supply is open witch off the appliance and pull out he mains plug Turn off the tap Unscrew water connection Qj m ean filter in the supply hose Screw water onnection on again Check for leaks econnect power supply Switch on e appliance ean filters See Cleaning and maintenance nstall hose without kinks remove any esidue Check connection to siphon and open if equired Lock cover correctly See Waste water pump Clean pump and lock cover correctly See Waste water pump 5 Not an appliance fault have the mains voltage and electrical installation checked 29 en Fault what to do Fault different error code is indicated on the digital display tto E 3D Display flashes Refill indicator for 5 and or rinse aid L6 is lit Refill indicator for 5 and or rinse aid L6 is not lit Water is left in the appliance at the end of the programme 30 Cause A technical fault has probably occurred Door not closed properly No rinse aid No salt Sensor does not detect salt tablets Refill indicator switched off There is still enough special salt rinse aid available Filter system or area under the filters is blocked The programme has not yet ended Remedial action Switch off appliances with the ON OFF switch 1 After a short time restart the appliance I
16. 5 W Water pressure at least 0 05 MPa 0 5 bar maximum 1 MPa 10 bar At a higher water pressure connect pressure reducing valve ahead Inlet rate minimum 10 litres minute Water temperature cold water hot water max temperature 60 C Capacity 12 15 place settings depending on model 38 Installation The required installation dimensions can be found in the installation instructions Level the appliance with the aid of the height adjustable feet Ensure that the appliance is situated securely on the floor m A built under or integrated appliance which is installed subsequently as a free standing appliance must be secured to prevent it from overturning e g by screwing it to the wall or by installing it under a continuous worktop which is screwed to adjacent cupboards m The appliance can easily be installed in a fitted kitchen between wooden and plastic walls Waste water connection 1 The required work sequence can be found in the installation instructions If required fit a siphon with an drainage connection 2 Connect the waste water hose to the drainage connection of the siphon with the enclosed parts Ensure that the drainage hose is not kinked crushed or twisted and that there is no cover plate in the drainage to prevent the waste water from flowing out Drinking water connection 1 Fasten the drinking water connection to the tap according to the installation instructions using th
17. 7 Installation and connection 37 Product package 37 Safety instructions 37 Delivery 38 Technical specifications 38 Installation 38 Waste water connection 38 Drinking water connection 39 Warm water connection 39 Electrical 4 39 Removing the appliance 40 22 40 Protection against frost Emptying the appliance 40 Intended use his appliance is intended for use in the home and the home environment Use the dishwasher only in the household and only for its designed purpose for washing domestic dishes Safety instructions Children from 8 years of age or people whose physical sensory or mental abilities or their lack of experience or knowledge prevent them from using the appliance safely must not use this appliance without supervision or instruction by a responsible person Before you switch ON the appliance Please read the operating and installation instructions carefully They contain important information on how to install use and maintain the appliance Retain all documents for subsequent use or for the next owner Delivery 1 Check the packaging and dishwasher immediately for damage caused in transit Do not switch on a damaged appliance but contact your supplier Please dispos
18. appropriate information contact the manufacturer of these appliances to ensure that the dishwasher can be installed above or below these appliances en Safety instructions If you cannot obtain any information from the manufacturer you must not install the dishwasher above or below these appliances If you install a microwave oven above the dishwasher the microwave oven may be damaged Install built under or integratable appliances only under continuous worktops which have been screwed to adjacent cupboards to ensure stability Do not install the appliance near heat sources radiators heat storage tanks cookers or other appliances which generate heat and do not install under a hob After installing the appliance ensure that the plug is easily accessible See Electrical connection Some models The plastic housing on the water connection contains an electric valve the connecting cables are in the supply hose Do not cut through this hose do not immerse the plastic housing in water In daily use Read and observe the safety information and instructions for use on the packaging for cleaning and rinsing agents Childproof lock door lock The description of the childproof lock is at the back in the envelope depending on model Damage he appliance may be repaired and opened up by a technician only To do this disconnect the appliance from the power supply Pull out th
19. arrow marks are opposite each other after closing the filter system Spray arms Limescale and contaminants in the rinsing water may block nozzles and bearings on the spray arms and 27 1 Check outlet nozzles on the spray arms for blockages 2 Unscrew the upper spray arm 23 3 Remove the lower spray arm upwards 4 Clean spray arms under running water 5 Re engage or screw on spray arms Fault what to do en Fault what to do Experience has shown that you can rectify most faults which occur in daily operation yourself This ensures that the machine is quickly available to you again In the following overview you can find possible causes of malfunctions and helpful information for rectifying them Note If the appliance stops during dishwashing or does not start for no obvious reason first run the Abort programme function Reset See chapter entitled Operating the appliance AN Warning Don t forget Repairs may be carried out by technicians only If a component has to be replaced ensure that only original spare parts are used Improper repairs or use of non original spare parts may cause considerable damage and put the user at considerable risk 27 en Fault what to do Waste water pump Large food remnants or foreign objects which were not captured by the filters may block the waste water pump The rinsing water will then be above the filter
20. ce function Spray arm strikes the utensils utensils not positioned correctly If there is a low load the water jets strike the washing tank directly Light utensils move during the wash cycle Handwash liquid in the rinse aid dispenser Rinse aid spilled Remedial action Close the door Check whether rear panel is being pressed in e g by socket or by hose holder which has not been removed Restore power and or water supply No remedial action possible Position utensils so that the spray arms do not strike the utensils Load the appliance with more utensils or distribute utensils more evenly in the dishwasher Arrange light utensils securely Immediately refill rinse aid dispenser with rinse aid Remove rinse aid with a cloth Customer service If you are unable to rectify the fault please contact your customer service We always find a suitable solution even to avoid unnecessary visits by technicians Contact information for your nearest customer service can be found on the back of these instructions for use or on the enclosed customer service list When calling please state the appliance number E Nr 1 and the production number FD 2 which can be found on the rating plate 34 on the appliance door Rely on the competence of the manufa cturer Contact us You can therefore be sure that the repair is carried out by trained serv
21. cription can be found in the back of the enve lope Do notallow children to play with or operate the appliance a Keep children away from detergents and rinse aid These may cause chemical burns in the mouth throat and eyes or asphyxiation Keep children away from open dishwasher The water in the rinsing compartment is not drinking water and could contain detergent residue Ensure that children do not place fingers in the tablet collecting tray 24 Small fingers could become caught in the slots en Protection of the environment When opening and closing the door on an eye level appliance ensure that children do not become jammed or crushed between the appliance door and the cupboard door below a Children could become locked in the appliance danger of suffocation or get into another dangerous situation Redundant appliances Pull out the mains plug sever and dispose of the power cord Destroy the door lock so that the door can no longer be closed Protection of the environment Both the packaging of new appliances and the old appliances themselves contain valuable raw materials and recyclable materials Please dispose of the individual parts separated according to type Please ask your dealer or inquire at your local authority about current means of disposal Packaging All plastic parts of the appliance are identified with internationally standardised abbreviations e g gt PS l
22. dispenser or cover guide blocked by sticky detergent residue Spray arms blocked by utensils therefore detergent is not rinsed out The detergent dispenser was damp when filled Fault what to do en Remedial action Use corrosion resistant cutlery Do not wash rusting parts Fasten salt dispenser lock firmly or remove Spilled salt Check mains fuse Ensure that the power cord is plugged all the way into the back of the appliance and into the socket Check that the socket functions Close the door Perform reset See Terminating the programme Deactivate childproof lock See instructions for use at the back Close door with increased force Check appliance installation Door or attached parts must close without obstruction Remove detergent residu Ensure that the spray arms can rotate freely Pour detergent into the dry detergent dispenser only 35 en Fault what to do Fault Appliance stops in the programme or programme is interrupted Filling valves making striking noises Knocking or rattling noise Unusual foam formation 36 Cause Door not closed properly Do not place utensils or fragrance dispenser in the tablet collecting tray Top basket presses against inner door and prevents door from being closed securely Power and or water supply interrupted Depends on domestic installation as appliance is not defective No effect on applian
23. drying of the utensils Cups and glasses Top basket Pans Bottom basket Tip Heavily soiled utensils pans should be placed in the bottom basket The more powerful spray jet provides a better dishwashing result Tip Other examples such as the best way of loading your dishwasher can be found on our homepage as a free download The corresponding Internet address can be found on the back page of these instructions for use Cutlery drawer Arrange the cutlery in the cutlery drawer as illustrated Separately arranged utensils are easier to remove after washing The drawer can be taken out down the side shelves to provide more room for taller items of cutlery The front rows of prongs can be folded down to provide room for wider handles Utensils en Folding spikes depending on model The spikes can be folded down to improve arrangement of pans bowls and glasses Small accessories holder depending on model Light weight plastic accessories e g lids etc can be held securely in the small accessories holder 15 en Detergent Adjusting the height of the basket The height of the upper utensils basket can be adjusted in 3 stages to create more space either in the upper or lower basket Appliance height 81 5 cm Top basket Bottom basket
24. e enclosed parts Ensure that the drinking water connection is not kinked crushed or twisted 2 When replacing the appliance always use a new water supply hose Water pressure At least 0 05 MPa 0 5 bar maximum 1 MPa 10 bar At a higher water pressure connect pressure reducing valve ahead Inlet rate Minimum 10 litres minute Water temperature e hot water max temperature Warm water connection depending on model The dishwasher can be connected to cold or hot water up to max 60 C Connection to hot water is recommended if the hot water can be supplied by energetically favourable means and from a suitable installation e g solar heating system with circulation line This will save energy and time The hot water setting 4 7 allows you to adjust your appliance optimally to operation with hot water It is recommended to have a water temperature temperature of the incoming water of at least 40 C and no more than 60 C It is not recommended to connect the appliance to hot water if the water is supplied from an electric boiler Installation and connection en Setting hot water 1 Open the door 2 Switch on ON OFF switch 1 3 Hold down programme button and press START button until 4 7 is indicated on the digital display 4 Release both buttons The LED for button flashes and the digital display displays the factory setting 5 Press programme butto
25. e g crystal glass objects may turn cloudy after many wash cycles Utensils en Glass and utensil damage Causes m Glass type and glass production process m Chemical composition of the detergent m Water temperature of the wash programme Recommendation m Use only glasses and porcelain which the manufacturer designates as dishwasher proof m Use a detergent which protects utensils m Take glass and cutlery out of the dishwasher as soon as possible after the programme ends Loading the dishwasher 1 Remove large food remnants It is not necessary to prerinse utensils under running water 2 Place the utensils so that they are secure and cannot tip over all utensils with their openings face down parts with curves or indentations are at an angle thereby allowing water to drain does not obstruct rotation of the two spray arms and 27 Very small utensils should not be washed in the machine as they may fall out of the baskets 13 en Utensils Unloading the dishwasher To prevent water from dripping off the upper basket onto the utensils in the lower basket it is recommended to empty the appliance from the bottom up Hot utensils are sensitive to shock Therefore when the programme ends leave the utensils to cool down in the dishwasher until they can be handled Note When the programme ends water droplets can still be seen inside the appliance This does not affect the
26. e mains plug or switch off the fuse Turn off the tap lf the appliance is damaged especially the fascia cracks holes broken buttons or the door function is impaired stop operating the appliance Pull out mains plug or switch off fuse Turn off tap call customer service Disposal 1 Make redundant appliances unusable to prevent subsequent accidents 2 Dispose of the appliance in a n environmentally friendly manner AN Warning Risk of injury o prevent injuries e g caused by stumbling open the dishwasher only briefly in order to load and unload the dishwasher Knives and other utensils with sharp points must be placed horizontally in the cutlery drawer Do not lean or sit on the open door n the case of free standing appliances ensure that the baskets are not overloaded a If the appliance is not in a cavity and a side panel is accessible the door hinge area must be covered at the side for reasons of safety risk of injury The covers are available as optional accessories from customer service or specialist outlets A Warning Risk of explosion Do not add any solvents to the washing chamber Danger of explosion Safety instructions en A Warning Risk of scalding Open the door carefully when the programme is still running There is a risk of hot water spraying out of the appliance A Warning Risks to children a If fitted use the childproof lock An exact des
27. e of the packaging material in an environmentally friendly manner Do not let children play with packaging and its parts There is a risk of suffocation from collapsible boxes and film Installation Following installation ensure that the back of the dishwasher is not freely accessible protection against contact due to hot surface Install and connect the appliance according to the installation and assembly instructions Prior to installation disconnect the dishwasher from the power supply Ensure that the protective conductor system of the domestic supply has been correctly installed Safety instructions en The electrical connection conditions must correspond with the specifications on the dishwasher rating plate 34 If the power cord of this appliance is damaged it must be replaced with a particular power cord To prevent injury the power cord may be purchased from customer service only If the dishwasher is installed in a high sided unit the unit must be secured properly If the dishwasher is installed below or above other domestic appliances follow the information for installation in combination with a dishwasher in the installation instructions for the particular appliances Also follow the installation instructions for the dishwasher to ensure that all appliances are operated safely If there is no information or if the installation instructions do not include the
28. ecommended to put a little less detergent in the detergent dispenser than for a full load B8 HygienePlus This function increases the temperatures and retains them for an extra long time to obtain a defined disinfection performance Continuous use of this function increases the hygiene status This additional option is ideal for cleaning e g chopping boards and baby bottles Intensive zone Perfect for a mixed load You can wash very soiled pots and pans in the lower basket together with normally soiled utensils in the upper basket The spray pressure in the lower basket is intensified the rinsing temperature is increased slightly High gloss drying By increasing the amount of water during the rinse cycle and extending the drying phase stains are prevented and the drying result is improved There is a slight increase in the energy consumption Rinse aid is recommended for the high gloss drying function even when using combination detergents Energy Save Water and energy consumption can be reduced with the Energy Save function The running time is extended for optimum cleaning and drying results Operating the appliance Programme data The programme data consumption values can be found in the summary of instructions They refer to normal conditions and the water hardness set value Different influencing factors such as e g water temperature or line pressure may result in deviations O
29. emaining time end of programme and if required low water level are displayed 5 702 Same as 5 0 i Other programme information is also displayed e g the symbol for half load or glass protection system active 5 01 1 is set at the factory To change the setting 1 Open the door 2 Switch on ON OFF switch 1 3 Hold down programme button and press START button until is indicated on the digital display 4 Release both buttons The illuminated display of the button A flashes 5 Keep pressing programme button A until the previously set value e g 5 0 is indicated on the digital display 5 0 for the optical display 6 Keep pressing programme button until the required value e g 5 02 is indicated on the digital display L3 7 Press START button 10 The set value is saved 8 Close the door Remaining running time display When the programme is selected the programme running time is indicated on the digital display When the programme has started the remaining running time is displayed on the floor only for settings 5 0 and 5 72 The running time is determined during the programme by the water temperature the number of utensils as well as the degree of soiling and may vary depending on the selected programme Timer programming You can delay the start of the programme in 1 hour steps up to 24 hours 1 Open the door
30. er connection 4 Loosen fastening screws for the furniture parts 5 If fitted remove the base panel 6 Pull out the appliance carefully pulling the hose behind 40 Transportation Empty the dishwasher and secure loose parts Drain the appliance according to the following steps 1 Turn on the tap 2 Open the door 3 Switch on ON OFF switch 1 4 Select programme with the highest temperature The expected programme duration is indicated on the numerical display c3 5 Press START button 10 6 Close the door Programme sequence starts 7 Open door after approx 4 minutes 8 Press START button until is indicated on the digital display 9 Close the door 10 Open door after approx 1 minute The numerical display indicates Bu 11 Switch off ON OFF switch 1 12 Turn off the tap disconnect supply hose and drain water Transport appliance upright only This prevents residual water from running into the machine control and damaging the programme sequence Protection against frost If the appliance is in a room where there is a risk of frost e g holiday home empty the appliance completely see Transportation Subject to changes Childproof lock door lock AN Warning 40 Activate the childproof lock Always close the appliance door completely 41 Open the door with activated when y
31. etergents containing salt component it can be Switched off m Proceed as described under Adjusting the water softening system and set the value to The water softening system and salt refill indicator are now switched off AN Caution Never fill the salt dispenser with detergent You will destroy the water Softening system 11 en Rinse aid Rinse aid As soon as the rinse aid refill indicator 6 is lit on the fascia there is still a rinse aid reserve of 1 2 rinsing processes Refill with rinse aid The rinse aid is required for stain free utensils and clear glasses Use only rinse aid for domestic dishwashers Combined detergents with rinse aid component may be used up to a water hardness of 21 dH 37 fH 26 Clarke 3 7 mmol l only If the water hardness is over 21 dH rinse aid must be used 1 Open the dispenser by pressing and lifting the plate on the cover 2 Carefully pour rinse aid up to the max mark in the filler opening 3 Close cover until it clicks shut 4 To prevent excessive foam formation during the next rinse cycle remove any rinse aid which has run over with a cloth Setting amount of rinse aid The amount of rinse aid can be set from 010 to 05 Please set rinse aid on 015 to obtain very good drying results 7 15 is already set in factory Change this setting only if streaks select lower setting or water stains select higher
32. f the problem recurs turn off the tap and pull out the mains plug Call customer service and mention the error code Close the door Ensure that no objects utensil fragrance dispenser are protruding over the basket and preventing the door from closing Refill rinse aid Refill with special salt Use different special salt Activation deactivation see chapter Water softening system Special salt or Rinse aid Check refill indicator levels Clean filters and area underneath see Waste water pump Wait until programme ends or reset see Terminating the programme Fault Utensils not dry Plastic utensils not dry Cutlery not dry Cause No or too little rinse aid in the dispenser Programme selected without Fault what to do en Remedial action Refill rinse aid Select programme with drying see drying Overview of programmes Programme Sequence Arrange utensils in a sloping position arrange affected utensils as sloping as possible Water collecting in depressions on the utensils and cutlery Use different combination detergent with The combined detergent used has a poor drying performance better drying performance Use of rinse aid also increases the drying performance Intensive drying to increase drying not activated Utensils were removed too early Activate intensive drying see Operating he appliance Wait until program ends or wait until 30 min
33. ge utensils in a sloping position Use rinse aid If required increase softening setting Change detergent brand Clean appliance mechanically Increase softening setting and change detergent if required Close salt dispenser cover correctly See Glass and utensil damage Change detergent brand Clean appliance mechanically Set water softening system according instructions for use or top up salt Set water softening system according o instructions for use or use separate detergents proprietary detergent salt rinse aid ncrease detergent dosage or change detergent Select a more intensive rinse programme Select programme with higher washing temperature Use suitable detergent at correct dosage Do not prerinse utensils Remove only large food remnants Recommended programme Eco 50 33 en Fault Coloured blue yellow brown difficult to remove to non removable coatings in the appliance or on Stainless steel utensils Coloured yellow orange brown easily removable deposits inside the appliance mainly in the floor area Plastic parts discoloured Removable streaks on glasses glasses with metallic appearance and cutlery Initial or existing irreversible clouding of glass 34 Fault what to do Cause Film formation consisting ingredients from vegetables g cabbage celery potatoes odles or the tap water e g manganese
34. he display jumps back tor PG 2 Press START button 10 The set value is saved 3 Close the door Switching off the appliance Short time after the end of the programme 1 Open the door 2 Switch off ON OFF switch 1 3 Turn off the tap not applicable if Aqua Stop fitted 4 Remove the utensils when they have cooled down Note When the programme ends leave the appliance to cool down a while before opening it This will prevent steam from escaping and causing long term damage to your built in furniture Interrupting the programme 1 Open the door 2 Switch off ON OFF switch 1 The LEDs go out The programme is saved If the door was opened on an appliance which has a warm water connection or is heated first leave the door ajar for several minutes and then close Otherwise expansion pressure may cause the appliance door to spring open or water to run out of the appliance 3 To continue the programme switch on the ON OFF switch again 4 Close the door Terminating the programme Reset 1 Open the door 2 Press START button for approx 3 sec The numerical display indicates LI LI 3 Close the door The programme sequence lasts approx 1 min On the digital display is indicated 2 02 4 Open the door 5 Switch off ON OFF switch 1 6 Close the door Changing the programme When the START button has been pressed the programme cannot be changed The only way
35. ice technicians who carry original spare parts for your domestic appliances Customer service en Installation and connection The dishwasher must be connected correctly otherwise it will not function properly The specifications for the inlet and outlet as well as the electrical connected loads must correspond with the required criteria as specified in the following paragraphs or in the installation instructions Install the appliance in the correct Sequence 1 Checking appliance on delivery Installing the appliance Waste water connection Drinking water connection Electrical connection ORON Product package If you have any complaints contact the dealer where you purchased the appliance or our customer service m Dishwasher Instructions for use Installation instructions Warranty Installation materials Steam guard plate Rubber apron Power cord depending on model BH NH NH NH NH NH Safety instructions Please follow the safety instructions under Installation 37 en Installation and connection Delivery Your dishwasher has been checked thoroughly in the factory to ensure that it is in working order This may cause small water stains These will disappear after the first wash cycle Technical specifications Weight max 60 kg Voltage 220 240 V 50 Hz or 60 Hz Connected load 2 0 2 4 kW Fuse 10 16 A UK 13A Power input switched off 0 5 W not switched off 0
36. ing the appliance Note Depending on the setting for Automatic switch off when programme ends or interior light the optical display is no longer or only briefly visible Automatic switch off after end of programme or interior light depending on model To save energy the dishwasher can be automatically switched off 1 min or 120 min after the programme ends The setting can be selected from to P Appliance does not switch off automatically The interior light comes on when the door is opened irrespective of whether the ON OFF switch is switched on or off When the door is closed the light is off If the door is open for longer than 60 min the light switches off automatically The interior light is lit only when the set value 7 07 is selected 1 Appliance switches off after 1 min Appliance switches off after 120 min 1 Open the door Switch on ON OFF switch 1 3 Hold down programme button and press START button until is indicated on the digital display 4 Release both buttons The LED for button LA flashes and the digital displa ae 3 displays the factory setting 5 Keep pressing programme button LA until the value 2 0 is indicated on the numerical db 3 N 24 To change the setting 1 Press programme button C Each time the button is pressed the set value increases by one level when the value of 2 72 has been reached t
37. n formation caused by metallic components on silver or aluminium utensils Film formation consisting of ingredients from food mnants and substances from Too low rinsing temperature Utensils precleaned too intensely e he tap water limescale soapy Remedial action Can be partly removed with machine cleaner or by mechanical cleaning Coatings are harmless Can be partly removed with machine cleaner or by mechanical cleaning Check function of the water softening system refill with salt or if using combined detergents tablets activate water softening system see chapter Water softening system Special salt Select programme with higher washing temperature Do not prerinse utensils Remove only large sensors therefore decide on weak programme sequence Stubborn soiling cannot be completely removed Too much rinse aid food remnants Recommended programme Eco 50 Set rinse aid amount to lower setting No rinse aid added or setting too low Detergent residue in the final Add rinse aid and check dosage recommended setting 4 5 Detergent dispenser cover must not be rinse programme section Detergent dispenser cover ocked by utensils cover does not open fully Utensils precleaned too intensely sensors therefore decide on eak programme sequence ubborn soiling cannot be completely removed Glasses not dishwasher proof onl
38. n until the factory set value R GG is indicated on the digital display 3 To change the setting 1 By pressing the button you can switch the hot water setting off 8 00 or on Hd 1 2 Press START button 10 The set value is saved 3 Close the door Electrical connection m Connect the appliance to an alternating current only ranging from 220 V to 240 V and 50 Hz or 60 Hz via a correctly installed socket with protective earth conductor See rating plate for required fusing 34 m The socket must be near the appliance and freely accessible following installation If the plug is not freely accessible an allpole disconnector with a contact opening of at least 3 mm must be fitted on the installation side to satisfy the relevant safety instructions m connection may be modified by technicians only 39 en Installation and connection m A power cord extension may be purchased from customer service only m Use only a residual current operated circuit breaker which features the symbol Gx Only this extension guarantees compliance with the currently valid regulations m The appliance features a water damage protection system Please note the system will not function unless the power supply is connected Removing the appliance Also observe the sequence of worksteps here 1 Disconnect the appliance from the power supply 2 Turn off the water supply 3 Undo the waste water and drinking wat
39. ogramme Use a detergent powder or select a more intensive programme Change detergent Fault Water stains on plastic parts Washable or water soluble coatings in the container or on the door White stubborn coatings limescale on the utensils container or door Tea or lipstick residue on the utensils Cause Droplet formation on plastic surface is physically unavoidable After drying water stains are visible Detergent substances are deposited These coatings cannot usually be removed with chemicals appliance cleaner If there is a white coating on the container floor the water softening system has been set marginally Salt dispenser cover not closed Only for glasses Initial glass corrosion can only apparently be wiped off Detergent substances are deposited These coatings cannot usually be removed with chemicals appliance cleaner Hardness range incorrectly set or water hardness greater than 8 9 mmol l 3in 1 detergent or bio eco detergent not effective enough ev Underdosing of detergent Too weak rinse programme selected Too low rinsing temperature Too little or unsuitable detergent Utensils precleaned too intensely sensors therefore decide on weak programme sequence Stubborn soiling cannot be completely removed Fault what to do en Remedial action Use a more intensive programme more water changes Arran
40. ou leave the appliance childproof lock This is the only way you can protect your 42 Deactivate childproof lock children from potential dangers Baking sheet spray head Large sheets or grilles and plates which have a diameter greater than 30 cm gourmet plates pasta plates dinner plates can be cleaned with the aid of the spray head To do this remove the top basket and insert the spray head as illustrated in the diagram To ensure that the spray jet can reach all parts arrange the baking sheets as illustrated max 4 baking sheets and 2 grilles Never operate the dishwasher without the top basket or baking sheet spray head some models 9000786191 en 9311 640TV
41. perating the appliance en Aqua sensor depending on model The Aqua sensor is an optical measuring device light barrier which measures the turbidity of the rinsing water The Aqua sensor is used according to the programme If the Aqua sensor is active clean rinsing water can be transferred to the next rinse bath and water consumption can be reduced by 3 6 litres If the turbidity is greater the water is drained and is replaced with fresh water In the automatic programmes the temperature and running time can also be adjusted to the degree of soiling Zeolith drying The appliance features a Zeolith container Zeolith is a mineral which can store moisture and heat energy and release them again During the washing step this heat energy is used to dry the mineral and heat up the rinsing water During the drying phase moisture from the washing compartment is stored in the mineral and heat energy is released This released heat energy is blown into the washing compartment with dry air This accelerates and improves drying These processes therefore save a great deal of energy A Caution Please ensure that the intake opening is not obstructed and do not place any temperature sensitive utensils in the lower basket at the rear right side above the blow opening 26 21 en Operating the appliance AN Warning Risk of injury Do not touch the blow opening 26 The blow opening becomes hot and furthermo
42. re any damage will result in a chargeable callout by customer service Switching on the appliance 1 Turn on the tap fully 2 Open the door 3 Switch on ON OFF switch 1 The Eco 50 programme display flashes This programme remains selected if no other programme button is pressed The expected programme duration flashes on the digital display 3 4 Press the START button 10 5 Close the door The programme starts running Note for environmentally friendly operation of the dishwasher For ecological reasons the Eco 50 programme is preset whenever the appliance starts This conserves environmental resources and not least Saves you money The Eco 50 programme is a particularly environmentally friendly programme According to EU regulation 1016 2010 it is the Standard programme which is the most efficient standard cleaning cycle for cleaning normally soiled utensils in terms of the combined energy and water consumption for cleaning these types of utensils 22 Optical display while the programme is running depending on model While the programme is running an optical display is indicated on the floor under the appliance door If the base panel is pulled forwards or if the appliance is installed at eye level with flush furniture front the display is not visible Possible settings of the optical display 5 00 The display is switched off 5 0 i Programme timer programming r
43. t polystyrene Therefore plastic waste can be sorted out when the appliance is being disposed of Please follow the safety instructions under Delivery Old appliances Please follow the safety instructions under Disposal of your appliance This appliance is identified according to the European guideline 2012 19 EU on waste electrical and electronic equipment WEEE The guideline specifies the framework for an EU wide valid return and re use of old appliances Getting to know your appliance Diagrams of the control panel and the interior of the appliance can be found in the envelope at the front Individual positions are referred to in the text Control panel ON OFF switch Programme buttons Digital display Display Check water supply Salt refill indicator Rinse aid refill indicator Timer programming display Timer programming Additional options START button Door opener Number depending on model HEPA E E E Getting to know your appliance en Appliance interior 20 Interior light 21 Cutlery drawer 22 Top basket 23 Top spray arm 24 Tablet collecting tray 25 Intake opening 26 Blow opening Zeolith container 27 Bottom spray arm 28 Dispenser for special salt 29 Filters 30 Bottom basket 31 Dispenser for rinse aid 32 Detergent dispenser 33 Lock for detergent dispenser 34 Rating plate
44. tly adhesive Auto 35 45 Energy Save of sensors temperature fresh food remnants Half load sensitive plastic Glossy drying and glasses Uo i Clean 45 7 DID i Glossy drying Intermediate rinse Quick 45 Final rinse 55 VIN m all types cold rinsing ER rane of utensils intermediate cleaning Prerinse 19 en Additional options Programme selection You can select a suitable programme according to the type of utensils and degree of soiling Information for test institutes Test institutes receive the information for comparability tests e g according to EN60436 These are the conditions for conducting the tests however these are not the results or consumption values Request by e mail to dishwasher test appliances com The product number E no and the production number FD are required which you can find on the rating plate on the appliance door 20 i Additional options depending on model Additional options can be set with the buttons G Express WashPlus Speed PerfectPlus VarioSpeedPlus This function can reduce the running time by approx 20 to 66 depending on the selected rinse programme To obtain optimum cleaning and drying results at a reduced running time water and energy consumption are increased Half load Ifyou have only a few items to wash e g glasses cups plates you can Switch to half load This will save water energy and time It is r
45. y suitable for dishwasher ez obstructed by utensils Do not place utensils or fragrance dispenser in the tablet collecting tray Do no prerinse utensils Remove only large food remnants Recommended programme Eco 50 Use dishwasher proof glasses Avoid long steam phase standing time after wash cycle ends Use wash cycle at lower temperature Set water softening system according to the water hardness if required one setting lower Use detergent with glass protection component Fault Rust spots on the cutlery The appliance does not start Programme starts automatically The door is difficult to open Door cannot be closed Cover on the detergent dispenser cannot be closed Detergent residue in the detergent dispenser or in the tablet collecting tray Cause Cutlery not adequately rust resistant Knife blades are frequently more severely affected Cutlery will also rust if rusting parts are rinsed at the same time pan handles damaged utensil baskets etc Salt content in the rinsing water too high as salt dispenser lock not fastened firmly or salt was spilled while being refilled The mains fuse has tripped Power cord not inserted The appliance door has not been shut properly You did not wait until programme ended Child proof lock is activated Door lock has been activated Door cannot be closed due to installation Detergent
46. ys the Lt 1b 1 factory setting To change the setting 1 Press programme button C Each time the button is pressed the set value increases by one level when the value of 4 07 has been reached the display jumps back to off 2 Press START button 10 The chosen setting has now been stored 3 Close the door Water hardness table Water Hardness hardness range 27 38 hard hard 5 5 8 9 38 54 Using special salt Always refill with special salt immediately before switching on the appliance This ensures that overrun special salt solution is immediately washed out and does not corrode the rinsing tank 1 Open the screw type cap of the compartment 28 2 Fill the tank with water only required when switching on the appliance for the first time 3 Then add dishwasher salt not table salt or tablets The water is displaced and runs out As soon as the salt refill indicator on the fascia is lit top up the salt depending on model Water softening system Special salt en Using detergents with salt component If combined detergents with a salt component are used salt can usually be omitted up to a water hardness of 21 dH 37 fH 26 Clarke 3 7 mmol If the water hardness is over 21 dH special salt must be used Switching off salt refill indicator water softening system If the salt refill indicator is impaired e g when using combined d
Download Pdf Manuals
Related Search