MANUALE D`USO END USER MANUAL
Contents
1. position NOTE do not keep the ignition key turned to ON for more than 3 otherwise the alarm will interpret the situation as a theft attempt e LED switch OFF showing the emergency procedure entry e Turn the ignition key in OFF position e After about 4 seconds the first 9 flashing sequence starts At the fifth LED flashing corresponding at Number 5 first digit of the pin code turn the ignition key in ON position then turn in OFF position or push the button on the LED e The LED will be switch OFF for about 4 seconds than a new 9 flash sequence will start At the fourth LED flashing corresponding at Number 4 second digit of the pin code turn the ignition key in ON position then turn in OFF position or push the button onthe LED e The LED will be switch OFF for about 4 seconds than a new 9 flash sequence will start At the sixth LED flashing corresponding at Number 6 third digit of the pin code turn the ignition key in ON position then turn in OFF position or push the button on the LED e The LED will be switch OFF for about 4 seconds than a new 9 flash sequence will start Atthe seventh LED flashing corresponding at Number 7 fourth digit of the pin code turn the ignition key in ON position then turn in OFF position or push the button onthe LED If the code is right the end of the emergency disarming by pin code will be indicated by the alarm with visual ac2. car in a parking lot or parking silo without creating useless alarm condition The brief optic acoustic signal consists of a low beep and the simultaneous flashing ofthe turn indicators NOTE the emission of the audio signals is subordinate to their being enabled when programming the accessory functions CURRENT ABSORPTION SENSOR ATTENTION before activating of the absorption sensor it is suggested to consult the specific rules being in force in your country noise pollution When the absorption sensor is activated a signal will be sent out at any minimal tension variation in the vehicle s electrical circuit for example lamp switching on ANTI DISTRACTION FUNCTION AND DOOR LOCKING This function determines the automatic activation of the system if this has been disarmed and no voluntary actions are performed by the user e g Door opening The function prevents the vehicle from being left unprotected in cases where after the arming of the system this is turned OFF accidentally by pressing the button N 1 of the remote control The self rearming is confirmed by the alarm with visual acoustic signalling one flash by the turn signals and one acoustic signal The anti distraction function activates the CDL control Therefore in order to prevent involuntary activations of the system it s MANDATORY to connect the door pin switch to the system input BROWN GREN wire of the alarm wiring harness NOTE after disarming a door opening will stop
3. the function Together with the previously described function the automatic door locking of the vehicle is done when running PAG 5 Being closed all the doors of the vehicle turn the ignition key to ON after 20 all doors will be locked By turning the ignition key to OFF all doors of the vehicle will be automatically unlocked To prevent this function from being activated accidentally the system continuously monitors the status of the ignition key and the input line of the DOORAND BOOT PUSHBUTTONS and therefore does not allow operation of the locks if the DOORS and BOOT are opened manually while starting the engine or during the 20 after starting it PASSIVE ARMING Automatic arming allows to have the alarm system active 45 seconds after the engine switching OFF After programming this function is obtained simply by turning the ignition key to OFF The alarm will indicate the passive arming activation by a long flash of the turn signals two flash of the status led and two acoustic signals When opening a vehicle s door during passive arming the arming time count will be set to zero and the led will be permanently illuminated when the door is closed the 45 counting will restart LOCKING TIME The standard locking time of the alarm is setto 0 5 In case the vehicle needs a locking time of 6 you can vary this parameter during the programming phase NOTE When the comfort function has been activa
4. CERTIFICATO DI INSTALLAZIONE Il sottoscritto installatore certifica di aver eseguito personalmente l installazione del dispositivo di allarme del veicolo descritto qui di seguito secondo le istruzioni del fabbricante INSTALLATION CERTIFICATE The undersigned qualified installer attests to have personally fitted the here described Vehicle Security sistem following the manufacturer instructions CERTIFICAT D INSTALLATION Je soussign installateur certifie d avoir fait personnellement l installation du dispositif d alarme du v hicule ci d crit conforme aux instructions du constructeur EINBAUBESCHEINIGUNG Der Installateur best tigt mit seiner Unterschrift dass die Alarmanlage in dem genannten Fahrzeug nach Vorgaben Des Herstellers eingebaut wurde CERTIFICADO DE INSTALACION El que suscribe instalador certifica el haber personalmente la instalaci n del dispositivo de alarma del veh culo descrito a continuaci n de acuerdo con las instucciones del fabricante _ CERTIFICADO DE INSTALA AO O abaixo assinado instalador certica que executou pessoalmente a instala o do dispositivo de alarme do ve culo descrito a seguir conforme as instru oes do fabricante By Da Par Von Por De Venduto il Tipo di prodotto Sold on Type of product Vendu le Type de dispositif Verkauft am Produktartikel Vendido el Dispositivo ciclo Vendido em Tipo de dispositivo Auto Car V hicule Fahrzeug Ve culo Firma Signature U
5. e ATTENTION for a correct work of the anti hijacking funtion it is necessary the connection of the BROWN GREEN wire to the doors switch DEVICE POWER ON The power on of the transmitter is obtained by pressing the button located on the TAG for al least 3 seconds the Led of the TAG will be lighted until the button will be released The status ON of the TAG is signalled by a short flash every 3 of the TAG s Led The coded data from the TAG are transmitted to the system periodically and when the system receives the signal the status led blinking DEVICE POWER OFF The power off of the transmitter is obtained by pressing the button located on the TAG until the Led will be lighted The status OFF of the TAG is signalled by 3 short flashes of the Tag s Led VEHICLE S STARTING Start the vehicle by turning in ON position the ignition key The system ref 7629 will wait a transmission from the TAG for a time of 2 minutes if one transmission will be detected the anti aggression function will be enabled Ifno transmission are received the anti aggression function is not enabled This automatic procedure allows to use the vehicle in security mode if the use forget the TAG or if the TAG is not properly working e g fault or battery discharged PAG 8 VEHICLE RUNNING USER AGGRESSION AND CAR HIJACKING ATTENTION For the correct work of the anti aggression function the user must hold the transmitter when the vehicle wi
6. g cycle SYSTEM ARMED After the inhibit time about 45 sec the system is armed and it is ready to detect any theft attempt When the system is properly armed the LED blinks After disarming the system any occured attempt will be indicated by the alarm with visual acoustic signalling ALARM HINIBIT TIME AND ALARM CYCLES As previously described any occured attempt will be indicated by the alarm with visual acoustic signalling After the alarm triggering before another alarm cause there are 5 seconds of neutral time that allow to disarm the system by emergency pin code The alarm signalling has 5 cycles of 30 seconds each for input and arming cycles The ignition key 15 54 and the cut wire alarm signalling have no limitation NOTE You can cut off the alarm cycle without deactivating the system by pressing key 2 on the remote ALARM DISARMING The alarm system can be deactivated by pressing key 1 on the remote or by inserting the electronic key into the appropriate receptacle Disarming is indicated by three turn signal flashes and three acoustic signals Ifan alarm condition has occurred it will be signalled by five turn signal flashes and five acoustic signals if these functions have not been excluded in programming stage See next paragraph for all signalling EMERGECY DISARMING BY PIN CODE The alarm system being described here has a RELEASE PIN CODE function which allows the user to turn off the protection device alar
7. ing disarmed open and keep it open the driver side door e Turn the ignition key to ON position e The status led stay on for 0 5 seconds during this time push together the two buttons of the remote control e Starting of programming procedure is indicated by two acoustic signals one with high tone and one with loud tones furthermore the led is permanently illuminated e To able and disable the functions follow the below table take into consideration that every time the push button of transmitter is pressed the system goes to the following function FUNCTION STATE Acoustic signals Enabled BUTTON Button N 1 Enable Button N 2 Disable Enabled panic Button N 1 Enable panic alarm Button N 2 Enable car finder Button N 1 Enable Panic alarm or car finder Current absorption sensor Disabled Button N 2 Disable Anti distraction automatic Disabled Button N 1 Enable door locking function Button N 2 Disable Passive arming Disabled Button N 1 Enable Button N 2 Disable Button N 1 Enable 6 Button N 2 Enable 0 5 Button N 1 Enable Button N 2 Disable Button N 1 Abilita Button N 2 Disable Setting of centralized lock times 0 5 6 sec a SecGen 25 seconds comfort closure command Disabled Disabled Double impulse in opening NOTE by turning the ignition key to OFF in any moment of the programming procedure the latter will s
8. ion use or tampering This alarm has exclusively a deterrent function against eventual thefts PAG 15
9. ll be invalidated e Turnthe ignition key to OFF Re turn the ignition key to ON for three consecutive times ignition key to ON and OFF within the maximum time of four seconds as mentioned before Afterthe third commutation letthe ignition key to ON e The alarm will indicate the procedure starting of new control device or magnetic contact learning by two long turn signal flashes and two acoustic signals one acute tone and the other loud tone ATTENTION do not modify the bonnet position otherwise instead of saving to memory new devices deletion of existing ones in the alarm s memory will take place e Now the alarm is waiting for receiving the device code e Press the radio control push button 1 introduce the electronic key in the specific receptacle press the TAG card button or make the magnetic contact to transmit bring near and then take away contact and magnet according to the device to be saved to memory In all four cases the alarm will indicate the new device learning by one turn signal flashing and one acute tone signal e Repeat the procedure to save to memory other devices e Turn the ignition key to OFF e The procedure completion will be indicated by one long turn signal flashing and one loud tone signal PAG 10 DELETION OF PROGRAMMED CONTROL DEVICES ATTENTION in order to carry out successfully the operation it is necessary to make the required electrical connection
10. ll be stolen If the driver s door will be opened during the vehicle running and the vehicle will be stolen the radio contact between the TAG transmitter and the alarm will be lost Sixteen seconds after the opening of the driver s door the system s status Led will be lighted in order to signal the activation of the anti aggression count down In this situation for safety reasons the car s running is not interrupted After one minute from the opening of the driver s door the system will enable the vehicle s immobilization as described in next paragraphs in addition to the sirene sound for 2 minutes INSTALLATION WITH CONNECTION OF THE ODOMETER SIGNAL The vehicle will be immobilized when the vehicle is running and its speed will be near to 0 km h The immobilization of the vehicle will be signalled by the flashing of the direction lights for about 3 hours NOTE the odometer sensor ref 7667 must be connected to the alarm system ref 7563 INSTALLATION WITHOUT CONNECTION OF THE ODOMETER SIGNAL The vehicle will be immobilized when the engine will be turned OFF for the first time It will not be possible to start again the vehicle s engine The immobilization of the vehicle will be signalled by the flashing of the direction lights for about 3 hours SYSTEM DISARMING WITH TAG CARD In order to disarm the engine s immobilization and to start again the vehicle it s mandatory to approach to the vehicle with the TAG t
11. m and or engine immobilizer if supplied remotes do not work or have been lost The foreseen PIN CODE is composed of four digits from of 1 to 9 The manufacturer s setting is 1 1 1 1 and are the same in all the alarm system 7563 Due to brevious safety reasons we reccomend to replace this original code with another user s customized code Please see at the relative paragraph for pin code programming pag 12 PAG 3 ALARM MEMORY When disarming the alarm if five turn signal flashes and five beep signals occur if this function have not be excluded in programming stage it is possible to identify the cause generating the alarm condition To do this turning the ignition key in ON position and see at the vehicle installed LED The LED will be blink shown the last alarm condition The cause of the alarm will indicate for 5 times This indication can be interrupted by turning the ignition key to OFF The possible alarm signalling are indicated in the under table LED SIGNAL CAUSE OF THE ALARM yer HOH Absorptions sensor 5 MELO Se se Positive under key 15 54 Infinite BE Se SE OBE 3 E Doors switches 5 HIKE HO OOO Cut wires Infinite SISI OJOS EE Trunk ee 5 JOSE Okka External magnetic contact 5 LED OFF 2 seconds LED ON 400mS GARAGE FUNCTION This function is used when the alarm disarming is required e g for maintenance without any intervention to the previous programmi
12. ng In fact this function disarms completely the alarm without any intervention when passive arming and against absent mindedness arming are programmed To do this proceed as follows e With the alarm system deactivated turn the ignition key to ON position e The status LED will turn on for approximately 0 5 e During this period putthe electronic key in the specific receptacle e The led is turned off to indicate the alarm de activation e To restore normal operating of programmed functions arm the alarm via the radio control PAG 4 PROGRAMMABLE FUNCTIONS ACOUSTIC SIGNALS This function allows the user to permanently exclude all acoustic signals See the relative paragraph for programming PANIC ALARM OR CAR FINDER If enabled the PANIC ALARM function allows the user to activate the visual and audio alarm signals deliberately by pressing key 2 on the remote This function works regardless of whether the alarm system is ON or OFF The alarm signal lasts up to approx 30 However you can silence it at any time by pressing key 2 on the remote again While the alarm signal is emitted the LED emits a continuous light If during the programming phase the PANIC function has been disabled the CAR FINDER function will be activated When the alarm is activated the CAR FINDER function allows you to obtain a short optic acoustic signal by pressing button N 2 on the remote TThis function can be useful to look for the
13. nterschrift Assinatura by GEMINI Technologies S p A Via Luigi Galvani 12 21020 Bodio Lomnago VA Italia Tel 39 0332 943211 Fax 39 0332 948080 Web site www gemini alarm com e mail info gemini alarm com e e 7 GEMITZ Y ALARM SYSTEMS 2888 2563 2562 2567 MANUALE D USO END USER MANUAL CD WO DM CP CE For all EU Countries AC 2628 Rev 01 10 04 DESCRPTION OF THE ALARM Dear Customer we invite you to read completely this manual in order to understand well how the alarm works and how to program easily the functions by remote control Below are described the alarm module fuctions e System arming and disarming by a transmitters with random rolling code e Passive arming function programmable e Blinker e Chirp programmable e Perimetric protection e Volumetric protection combined with an ultrasonic or hyperfrequency module excludable from arming e Control for CDL electrical widows and sun roof e Electrical engine immobilizer e Alarm memory indicated by optic acousticl signals e PANIC or CAR FINDER function e Emergency disarming by means of PIN CODE e Anti hijacking function e Garage function NOTE indications included in this manual refer to the most complete device of the 7563 alarm series OPERATING DESCRIPTION COMPLETE ALARM ARMING The alarm can be activated by pressing key 1 on the remote or by inserting the electronic key into the appr
14. opriate socket The operation is confirmed by an acoustic signal and a visual signal consisting of one flash of the turn indicators lasting approximately one second The alarm hasa 45 pre arming neutral time During the first 25 of this time it is possible to exclude the sensor as described in the specific paragraph ARMING WITH SIREN SOUND EXCLUSION This function allows the user to arm the alarm system excluding the siren sound in case of a theft attempt To exclude the siren proceed as follows e Turn the ignition key to ON position e The status will stay on for 0 5 seconds During this time push the button N 2 of the transmitter e Go away from the vehicle and push the button N 1 of the transmitter e The alarm will be armed with the optical and acoustic signals which as previously described will be not activated in case of a theft attempt NOTE the siren sound exclusion is bound to the single arming cycle This function is applied close to the hospitals PAG 2 ARMING WITH VOLUMETRIC PROTECTION EXCLUSION AND COMFORT FUNCTION This function allows the user to arm the system with volumetric protection and of the comfort function being excluded Push the button N 1 of the transmitter and during the 25 of the neutral time push the button N 2 of the transmitter After this procedure a single short flashing of turn signals will take place NOTE the procedure described above is bound to the single armin
15. oustic signalling Vice versa if the inserted numbers are wrong the alarm will start triggering again In this case repeat all procedure PAG 13 REPLACEMENT OF DEVICE BATTERIES The use of batteries which are different from the suggested one could provoke irremediable damage to the device Do not waste the environment with exhausted batteries but use for their disposal the specific waste containers MAGNETIC CONTACT The led s light intensity indicates the battery charge state of the magnetic contact e Intermittent light or low intensity of the led uncharged battery e Permanent light or high intensity of the led charged battery To replace the batteries proceed as follows e With the alarm being disarmed open the cover of the magnetic contact e Remove the exhausted batteries and replace with new being careful to not invert the polarity e Put back the cover of the magnetic contact ATTENTION use only batteries of CR1616 type gt LITHIUM BATTERY COC CR1616 3V BATTERY REPLACEMENT Open the TAG s plastic making level with a screwdriver on the hole close to the slot Figure 1 Remove the circuit and pull out the uncharged battery position the charged battery keeping the negative pole upwards Figure 2 Remount all components being sure that closure is correct and efficient Note in order to achieve longer life of the battery it is suggested to turn off the device when it i
16. ransmitter switched ON When the module recived again the TAG codified signal it deactive the anti hijacking function and stop turn signals flashes SYSTEM DISARMING WITHOUT TAG CARD This procedure can be used if there are some problems with the TAG card or with the anti hijacking function ex Damage or battery discharge of the TAG card with enabled anti hijacking function and vehicle running It s possible to disarm the engine s immobilization with the following procedure e Push the button located on the status Led or insert the electronic key into the receptacle after at least 2 minutes from the start of the engine s immobilization e Push within 2 seconds the button N 2 of the remote control and then press within 2 seconds the button N 1 of the remote control PAG 9 LEARNING OF NEW CONTROL DEVICES ATTENTION in order to carry out successfully the operation it is necessary to make the required electrical connections door switch bonnet switch and positive under key The alarm can save to memory a maximum number of 12 control devices either radio controlled or electronic keys TAG cards or magnetic contact the later as a protection device Proceed as follows e With the alarm being disarmed open and keep open the bonnet and the driver side door e Turn the ignition key to ON ATTENTION the following operations must be carried out within four seconds otherwise the new device memorizing procedure wi
17. s door switch bonnet switch and positive under key The alarm is equipped with a deletion procedure of new control devices either radio controlled or electronic keys TAG cards or magnetic contact the later as a protection device Proceed as follows e With the alarm being disarmed open and keep open the bonnet and the driver side door e Turn the ignition key to ON ATTENTION the following operations must be carried out within four seconds otherwise the new device deletion procedure will be invalidated e Turn the ignition key to OFF e Re turn the ignition key to ON for three consecutive times ignition key to ON and OFF within the maximum time of four seconds as mentioned before Afterthe third commutation letthe ignition key to ON e The alarm will indicate the procedure starting of new control device or magnetic or magnetic contact deletion by two long turn signal flashes and two acoustic signals one acute tone and the other loud tone e Close the bonnet e The led will be illuminated constantly e Keep the bonnet close till the moment the complete deletion of devices via radio will take place after about four seconds NOTE keeping the bonnet close for less than four seconds the device deletion via radio will be unsuccessful e The procedure completion will be indicated by leds turning off by one long turn signal flashing and one loud tone signal e Turn the ignition key
18. s not used Figura 2 PAG 14 TRANSMITTER The radio control is equipped with a device which indicates the battery charge status During normal operating of the radio control when pushing the control button the green led will be permanently illuminated If the battery charge status is under the level required for good operating when pushing the system arming disarming button the green led will be flashing in order to warn the user that battery replacement is needed In this case open the radio control with a light pressure between the two shells and then replace the batteries ATTENTION use only batteries of CR1616 type 3Volt T BATTERIE OF CR 1616 TYPE WARRANTY CONDITIONS This apparatus is guaranteed against all defects of fabrications for a period of 24 month from the installation date shown on this warranty coupon taking into consideration the 1999 44 CE Therefore you are kindly requested to fill entirely the guarantee certificate included in this booklet and to NOT REMOVE the guarantee label from the device Missing or tearing of this label missing of one part of guarantee certificate or missing of the enclosed sale document will invalidate the guarantee The guarantee is valid exclusively to Gemini Technologies S p A Authorized Service Centers The manufacturer will decline any responsibility for any eventual malfunctions of the device or electrical plant damages of the vehicle due to improper installat
19. ted let the locking time set to 0 5 In fact if the locking time is set to 6 when the alarm is disarmed the windows ofthe vehicle will open COMFORT CONTROL The comfort control allows the automatic regulation of window closing when the alarm is armed In fact after this function has been activated at any alarm arming the window winder motor control unit will receive a 25 command to close the windows CDL DOUBLE OPENING PULSE By enabling this function you will obtain upon deactivation of the system a double control pulse on the door unlocking line about 0 5 second each This allows the opening of the centralized door locks on vehicles having the diversified door opening first pulse driver side door opening second pulse other doors opening This function is active only if the opening closing time of 0 5 is selected while setting the opening closing timo of 6 will automatically disabled the double pulse PAG 6 PROGRAMMING THE ALARM SYSTEM Has been previously programmed with standard configuration during manufacturing procedure by Gemini and can be modified in any moment During the programming phases press the radio control rough push button n 1 for function activation and the smooth push button n 2 for function de activation ATTENTION pay attention to not modify the functions which have been programmed during the installation For the programming modification proceed as follows e With alarm be
20. ter a four second pause state led will start with a new sequence of flashes At the sixth LED flashing corresponding at Number 6 third digit of the pin code push the button on the LED or turn the ignition key in ON position for one second Turn the ignition key in OFF position e After a four second pause state led will start with a new sequence of flashes At the seventh LED flashing corresponding at Number 7 fourth digit of the pin code push the button on the LED or turn the ignition key in ON position for one second Turn the ignition key in OFF position e The alarm system will indicate the end of the PIN CODE personalizing procedure by two acousic signal with low tone and one with high tone ATTENTION If during one of four nine flashing sequences no number is confirmed value O at the end of 9th flash the PIN CODE procedure will stop automatically PAG 12 EMERGENCY DISARMING BY PIN CODE The procedure for emergency disarming by pin code is the following Kindly note that the standard pin code programmed is 1 1 1 1 The same number used for pin code programmation 5 4 6 7 has been used also for emergency disarming example e Cause an alarm condition e Leave the alarm triggering for the standard timing about 30 seconds and wait for the inhibit time between two alarm signalling e During the inhibit time the LED remain steadly ON for about 5 seconds Turn the ignition key in ON
21. to OFF NOTE the control device deletion does not imply any modification of programmed functions PAG 11 PROGRAMMING NEW PIN CODE The procedure to program pin code is specified here below It is better to personalize the code as customer has required In this example supposing that the pin code is 5 4 6 7 e With the alarm being disarmed open the driver side door and keep it open e Turn the ignition key in On position The status Led will be turned on for 0 5 seconds during this period press simultaneously the two buttons of the transmitter After this procedure two acoustic signals will be sent out one with acute tone and the other with loud tone e Close and keep closed the driver side door e Press simultaneously the two radio control buttons the led will be turned off e Turn the ignition key in OFF position e After a four second pause state led will start with the first sequence of flashes At the fifth LED flashing corresponding at Number 5 first digit of the pin code push the button on the LED or turn the ignition key in ON position for one second Turn the ignition key in OFF position e After a four second pause state led will start with a new sequence of flashes At the fourth LED flashing corresponding at Number 4 second digit of the pin code push the button on the LED or turn the ignition key in ON position forone second Turn the ignition key in OFF position e Af
22. top and successive functions will remain unchanged e Once the last function has been programmed the alarm will confirm that the programming has been disabled with two acoustic signals with low tone one acoustic signal with high tone furthermore the led will be turned off e Turnthe ignition key to OFF position PAG 7 ANTI HIJACKING FUNCTION We suggest to keep the TAG separately from the remote control usually kept with the vehicle key for safety reasons and to enable the anti hijacking function to control the vehicle speed NOTE activation of the anti hijacking function does not mean the vehicle immobilization but the starting of the reception procedure and authentication of the radio code The system ref 7629 is equipped with the anti aggression function This function is able to immobilize the engine in case of an aggression against the vehicle s owner The anti aggression function is based on the use of an automatic transmitter called TAG ref 7708 the which code is memorized in the system When the vehicle is running or in any case when positive under key is present not receiving the signal sent out from the TAG the module will be activated with the anti robber function immobilizing the vehicle as described in next chapters In order to avoid involuntary activation of the anti robber system and consequently the vehicle s immobilizing you must pay attention to its state when you are close to the vehicl
Download Pdf Manuals
Related Search