71161_00001.C Flanged Globe Valves 2½” to 6
Contents
1. L is for Lower the bypass port C is for Common Viewed with the bonnet upwards ad the U port on the left the L port is the bottom port and the C is the right port With the stem up L is open to Common With the stem down U is open to Common Flanged Globe Valves 212 to 6 Installation Instructions AT BELIMO FLOW PATTERN Flow Pattern is Marked on Valve G7 D 3 way Diverting Valve Stem Up Open AB to B G6 2 way Valve Stem Up Open A to AB G7 3 way Mixing Valve Stem Up Open B to AB VALVE ASSEMBLY SET UP POSITION NON SPRING RETURN STAYS IN LAST LLI LL Te A c cc Lid l L4 Flow arrow shown on rear of valve 2 WAY VALVE SPECIFY UPON ORDERING SPECIFY UPON ORDERING 3 WAY VALVE SPECIFY UPON ORDERING SPECIFY UPON ORDERING EV RV Series NC Normally closed A to AB valve will Open upon increase in signal power Note To change valve to A to AB open reverse the directional switch in actuator NO Normally open A to AB valve will close upon increase in signal power Note To change valve to A to AB closed reverse the directional switch in actuator NC Normally closed A to AB will open upon increase in signal power Note To change valve to A to AB open reverse the directional switch in actuator NO Normally open A to AB will close upon increase in signal power Note To change valve to A to AB closed2. 24 VAC Transformer Control Signal 21010 VDC or 4to 20 mA Wht 3 Y input 2to 10 V Org 5 Output 2to 10 V 500 Q 1 4 watt Wht 3 Y Input 2t010V d Org 5 U VDC 4 to 20 mA Master Slave Actuators with appliance cables are numbered Actuators may be connected in parallel Power consumption and input impedance must be observed Actuators may also be powered by 24 VDC Only connect common to neg leg of control circuits A500 Q resistor converts the 4 to 20 mA control signal to 2 to 10 VDC Control signal may be pulsed from either the Hot Source or Common Sink 24 VAC line Contact closures A amp B also can be triacs amp B should both be closed for the triac source and open for triac sink For triac sink the Common connection from the actuator Position feedback cannot be used with a triac sink controller The actuator internal common reference is not compatible Actuators with plenum rated cable do not have numbers on wires use color codes instead All 120 VAC 230 VAC and UP actuators use appliance rated cables UP models use L instead of H on 2 wire gt bb PR PPP PPP must be connected to the Hot connection of the controller Anaranjado Alaranjado E ab ab Belimo wordwide www belimo com BELIMO Americas USA Locations 43 Old Ridgebury Road Danbury CT 06810 Tel 800 543 9038 Fax 800 228 8283 marketing
3. Sink 24 VAC line Contact closures A amp B also can be triacs amp B should both be closed for the triac source and open for triac sink For triac sink the Common connection from the actuator must be connected to the Hot connection of the controller Position feedback cannot be used with a triac sink controller The actuator internal common reference is not compatible Actuators may be connected in parallel if not mechanically mounted to the same shaft Power consumption and input impedance must be observed Actuators with plenum rated cable do not have numbers on wires use color codes instead All 120 VAC 230 VAC and UP actuators use appliance rated cables UP models use L instead of on 2 wire 16 Anaranjado Alaranjado E ab ab AT BELIMO MFT95 na Sotero Damper Position The direction of rotation switch is set so that the fail safe position and the position of the damper is closed with no signal at wire R AN 24 VAC Transformer Line Common Volts Hot A A A 135 Q gt 1 R e B US Output 2 to 10 VDC PANA VAC Transformer Line C Volts Common Hot 3 W R B US Output 2 to 10 VDC G6 G7 Globe Valves with Single Mount AFX Actuators Wiring Diagrams A 24 VAC Transformer Line Common Volts Shunting Resistor Series 90 Controller Common Hot 53 actuators Resistance 14
4. A to AB Fail Position Will default fail A to AB open from the factory Fail position can be set from 0 100 in 1096 increments 3 WAY DIVERTING VALVE NC Normally closed B to AB valve will open upon increase in signal power Note To change reverse the directional switch NO Normally open B to AB valve will close upon increase in signal power Note To change reverse the directional switch 01 14 Subject to change Belimo Aircontrols USA Inc 01 14 Subject to change Belimo Aircontrols USA Inc M Flanged Globe Valves 212 to 6 BELIMO Piping Instructions 2 WAY 2 way Valve Piping Diagram 1 Input 1 Output q Return A AB Coil Supply 3 WAY MIXING 3 way Mixing Valve Piping Diagram Mixing with Coil Pump 2 Inputs 1 Output A AB Return Coil 3 WAY DIVERTING 3 way Diverting Valve Piping Diagram 1 Input 2 Outputs Return Coil INSTALLATION Valve must be installed in these orientations only Linear Actuators UGLK Linkage Flanged Globe Valves 212 to 6 Installation Instructions ME BELIMO ANSI 125 Flange Detail for American Standard 125 Ib Cast Iron Pipe Flanges FLANGES DRILLING BOLTING 0 Nominal A Flange Flange C Diameter of D Diameter of Number Diameter Length of Pipe Size Diameter Thickness Bolt Circle Bolt Holes
5. Function a o 24 VAC up to 240 VAC Controller 24 VAC Transformer Control Signal e VDC mA 2to 10 VDC Feedback Signal VDC 4to 20 mA 24 VAC Transformer Controller Triac Sink Triac Source Triac Sink with Separate Transformer 24 VAC Transformer 24 VAC Transformer 24 VAC Transformer AC only UN Line Hine Volts Line Bik 1 Common Volts Volts Red 2 Hot z Wht 3 Y Input Position Position Feedback VDC 4 2 to 10 VDC O Feedback VDC Feedback Signal Function 1 100 lt Default selectable 0 100 See Configuration Data Sheet Customizable See Configuration Data Sheet On Off Floating Point PWM 24 VAC Transformer A N A 24 VAC Transformer AC Only Notes Meets cULus requirements without the need of an Line Line electrical ground connection Volts Volts Control Signal C VDC mA 2 to 10 VDC B Feedback Signal Actuator Wire Number Color merus s on VDC 4 to 20 mA Y4 Input 2 to 10V U Output 2 to 10V Control Signal j E 2 10 VDC or 4to 20 mA 500 1 4 watt Min Max Normal Default selectable 0 100 See Configuration Data Sheet Customizable See Configuration Data Sheet Override Control Min Mid Max Postions 10 to 90 Auxiliary Switches Master Line Blk 1 Common Volts Red 2 Hot
6. reverse the directional switch in actuator AFB AFX Series On Off NO FO Normally open A to AB valve will drive closed Spring Action Will fail open A to AB upon power loss NC FC Normally closed A to AB valve will drive open Spring Action Will fail closed A to AB upon power loss NO FO Normally open A to AB valve will drive closed Spring Action Will fail open A to AB upon power loss NC FC Normally closed A to AB valve will drive open Spring Action Will fail closed A to AB upon power loss NO FO Normally open A to AB Spring Action Will fail open A to AB upon power loss NO or NC action can be chosen with CW CCW switch NO FO Normally open A to AB Spring Action Will fail open A to AB upon power loss NO or NC action can be chosen with CW CCW switch 2 2 NC FO Normally closed A to AB valve will NO FC or NC FC Normally Open NC FO Normally closed A to AB valve will NO FC or NC FC Normally Open cc D open upon increase in signal Note To Normally Closed valve can be open or open upon increase in signal Note To Normally Closed valve be open or 5 change valve to A to AB open reverse CW closed will drive closed or open A to AB change valve to A to AB open reverse CW closed will drive closed or open A to AB a A CCW switch Spring Action Will fail open can be chosen with CW CCW switch CCW switch Spring Action Will fail open can be chosen with CW CCW switch eos A to AB up
7. us belimo com 1049 Fortunato Loop Sparks NV 89436 Tel 800 987 9042 Fax 800 987 8875 marketing us belimo com Canada Locations 5845 Kennedy Road Mississauga Ontario L4Z 2G3 Tel 866 805 7089 Fax 905 712 3124 marketing us belimo com Latin America and the Caribbean Customer Service Tel 203 791 8396 Fax 203 791 9139 marketing us belimo com Belimo Brasil Com rcio de Automa o Ltda Tel 55 11 3643 5656 Fax 55 11 3643 5657 atendimentoaocliente br belimo com PLA BELIMO
8. way 68 340 Three way Mixing 68 248 Three way Diverting Stainless steel stem Bronze plug or Stainless plug On Off Floating Point 2 10 VDC Multi Function Technology Electronic Fail Safe or Non Spring Return e Complete flanged product range e Mixing or diverting options e Multi Function Technology e ANS 125 ANSI 250 BENEFITS e Fits wide range of applications e Capable of any control signal e Suitable for piping systems PLA BELIMO 01 14 Subject to change O Belimo Aircontrols USA Inc 01 14 Subject to change Belimo Aircontrols USA Inc PLA BELIMO Warning Valve should not be used for combustible gas applications Gas leaks and explosions may result Do not install in systems which exceed the ratings of the valve e X Avoid installations where valve may be exposed to excessive moisture corrosive fumes vibration high ambient temperatures elements or high traffic areas with potential for mechanical damage e Valve assembly location must be within ambient ratings of actuator If the temperature is below 22 F a heater is required e he valve assembly will require heat shielding thermal isolation or cooling at the actuator if combined effect of medium and ambient temperatures conduction convection and radiation is above 122 F for prolonged time periods e Strainers should be installed before coil and valve e Visual access must be provided Assembly must be
9. 0 0 7150 4 4750 37 5 Q 6 280 Toother Resistor Kit No ZG ROS actuators Override Wiring multiple actuators to a Series 90 Controller 24 VAC T f M quc ranstormer ini iti AX 24 Transformer o Ad Line Common Line Volts Hot Volts Series 90 Controller AA Series 90 R Controller B Series 90 low limit control US Output 2 to 10 VDC 135 Q for 0 to 50 control 280 Q for 0 to 100 control Low Limit Control AN 24 VAC Transformer Line Common Volts Hot AN Aw Series 90 Controller Series 90 high limit control 280 Q Shunting Resistor H205 Change over Controller Occupied Contact To other actuators Q209A Minimum Position AN 24 VAC Transformer Potentiometer AN Line Volts H205 Changeover Controller A Shunting Resistor Occupied Contact Honeywell T675A Morning Warmup W973 W7100 Controller Common Hot AN w A No o actione Resistance R 13000 13000 192 B U5 Output 2 to 10 VDC Resistor Kit No ZG RO6 To other actuators Used with the W973 and W7100 controllers Honeywell Q209A Minimum Position AN 24 VAC Transformer Potentiometer Common Hot AN Shunting Resistor W973 W7100 T775 Honeywell T675A Morning Warmup Common Hot AN w A R B U5 Output 2 to 10 VDC To other ac
10. 01 14 Subject to change Belimo Aircontrols USA Inc 71161 00001 C INSTALLATION INSTRUCTIONS Flanged Globe Valves 2 2 to 6 Pressure Compensated G6 C Series G6 C Two way Pressure Compensated G6 CS Two way Pressure Compensated Stainless Steel Trim G6 LCS Two way Pressure Compensated Stainless Steel Trim Linear Characteristic 212 to 6 Service Chilled hot water 60 glycol steam C Range 65 344 Material Stainless steel stem Bronze plug or Stainless plug Control On Off Floating Point Multi Function Technology Electronic Fail Safe or Non Spring Return FEATURES e Balanced Plug Design e Spring Return Solutions for up to 6 Valves Bronze or Stainless Trim BENEFITS e Perfect for high close off requirements e Fail safe on larger valves e Covers wide range of operating temperatures e Modified equal percent G6C G6CS or linear characteristic G6LCS for steam applications AT BELIMO Flanged Globe Valves 212 to 6 Installation Instructions Flectronic 36 C S G7 S Series G6 C S 250 G7 S G7 S 250 Two way Flanged ANSI 250 Bronze or Stainless Trim Three way Flanged Bronze or Stainless Trim Three way Flanged ANSI 250 Bronze or Stainless Trim Three way Valves available in Mixing or Diverting Service C Range Material Control FEATURES 215 to 6 Chilled hot water 60 glycol steam G6C 65 344 Two
11. A eX d 5 e NS MAN UNS Q S NO SN N 2 ee t YYYYYYYYYYYP A A a ss m oN ir f SAPS OE LA 3 6 v Y DZ men ANY ADD ANN Peg lit ec 2 B gg e 7 jj iii 01 14 Subject to change Belimo Aircontrols USA Inc 2s BELIMO Electronic Fail Safe Actuator with 3 and SR G6 G7 Globe Valves with Dual Mount GK X1 Actuators Wiring Diagrams 24 VAC Transformer 24 VAC Transformer 24 VAC Transformer N Line Line Line Volts Volts Volts Control Signal VDC mA B tj 2 to 10 VDC o Feedback Signal Function b Max 100 lt t Cw On Off Floating Point VDC 4to 20 mA 24 VAC Transformer Master Line O Bik 1 Common 100 to 240 VAC 100 to 240 VAC Volts Ll nea 2 Hot Line N L1 Line N L1 NE spi ch 4 Wht 3 Y Input 2 to 10 V Hot H L2 Hot H L2 4to 20 mA Org 5 output2t010V a 52 Max 100 lt AJA On Off Floating Point Wht 3 Y Input 2 to 10 V il Org 5 U VDC 4 to 20 mA Master Slave Line Volts Controller Triac Sink Electronic Fail Safe Actuator with MFT AVA 24 VAC Transformer Line Volts 2 to 10 VDC Feedback Signal F
12. Only connect common to neg leg of control circuits A 500 resistor converts the 4 to 20 mA control signal to 2 to 10 VDC Control signal may be pulsed from either the Hot Source or Common Sink 24 VAC line gt Contact closures amp B also can be triacs A amp B should both be closed for the triac source and open for triac sink For triac sink the Common connection from the actuator must be connected to the Hot connection of the controller Position feedback cannot be used with a triac sink controller The actuator internal common reference is not compatible IN4004 or IN4007 diode IN4007 supplied Belimo Part number 40155 Actuators with plenum rated cable do not have numbers on wires use color codes instead Pp b P O E Z lt Alaranjado Vermelho AT BELIMO Non Spring Return Actuator with 3 AY A 24 VAC Transformer Line Volts On Off Non Spring Return Actuator with MFT 24 VAC Transformer Line Volts 5 2 to 10 VDC Feedback Signal On Off AVA WGVL G6 G7 Linkage with RV Series Actuators 24 VAC Transformer Floating Point 24 VAC Transformer Line Volts 2 to 10 VDC a Feedback Signal Floating Point 24 VAC Transformer Line Volts 28 Control Signal C VbC mA 9 9 VDC 4to 20 mA 24 VAC Transformer AC Only Line Volts Contr
13. accessible for routine service Contractor should provide unions for removal from line and isolation valves e Avoid excessive streses Mechanical support must be provided where reducers have been used and the piping systems may have less structural integrity than full pipe sizes e Vertical pipes with valves and dual actuators may require support for linkage e Sufficient upstream and downstream piping runs must be provided to ensure proper valve capacity and flow response Five diameters in each direction are reccomended e Life span of the valve stems and packing is dependent on maintaining non damaging conditions Poor water treatment or filtration corrosion scale or other particulate can result in damage to trim components A water treatment specialist should be consulted 1 Inspect shipping package valve linkage and actuator for physical damage If shipping damage has occurred notify appropriate carrier Do not install 2 If this is a replacement remove the existing valve linkage and actuator from the piping system 3 If actuator and linkage are removed they must be reinstalled correctly The actuator must be rotated so that the valve seats properly for close off 4 Install valve with the proper ports as inlets and outlets See piping charts on next page Check that inlet and outlet of 2 way valves are correct check that the A and AB ports of 3 way valves are piped correctly Flow direction arro
14. e Volts Control Signal x VDC mA 2 to 10 VDC Feedback Signal Actuator Wire Number Color merus 5 on VDC 4 to 20 mA 24 VAC Transformer AC Only Line Volts Control Signal e 2 10 VDC or 4 to 20 mA 9 500 Q 1 4 watt Default selectable 0 100 See Configuration Data Sheet Customizable See Configuration Data Sheet Override Control Min Mid Max Postions 10 to 90 Auxiliary Switches P P PPP PPP Triac Sink Triac Source Triac Sink with Separate Transformer 24 VAC Transformer 24 VAC Transformer 24 VAC Transformer AC only OA Line Line Line Bik 1 Common Volts Volts Red 2 Hot JN O Wht 3 Y Input _ AN Positi Position Fee mh UbC U Output Feedback DE 2 to 10 voc C Feedback Signal 100 lt Default selectable 0 100 See Configuration Data Sheet Customizable See Configuration Data Sheet On Off Floating Point PWM Notes Meets cULus requirements without the need of an electrical ground connection Actuators with appliance cables are numbered Actuators may be connected in parallel Power consumption and input impedance must be observed Actuators may also be powered by 24 VDC Only connect common to neg leg of control circuits A500 resistor converts the 4 to 20 mA control signal to 2 to 10 VDC Control signal may be pulsed from either the Hot Source or Common
15. iring Diagrams Non Spring Return Actuator with 3 AAAI 24 VAC Transformer Line l Volts i Floating Point 100 to 240 VAC Line N L1 Hot HL2 LE Floating Point AT BELIMO Non Spring Return Actuator with SR ALY 24 VAC Transformer Line Volts Control Signal e VDC mA VDC 4to 20 mA Signal Direction Selector Switches 24 VAC Transformer Line Volts On Off 100 to 240 VAC Line NLI Hot H L2 l On Off Line Volts Controller Triac Sink Non Spring Return Actuator with MFT AVA Controller Triac Source 1 1 4 watt m Control Signal vocima 9 9 VDC 4 to 20 mA 24 VAC Transformer 24 VAC Transformer Line Line Volt Volts mS e i Feedback Signal 2 to 10 voc SIS lt Feedback Signal On Off Floating Point 24 VAC Transformer 24 VAC Transformer AC Only 6 Line 08 Volts Volts Control Signal vocima amp e et 500 Q 1 4 watt Default selectable 0 100 See Configuration Data Sheet Customizable See Configuration Data Sheet Override Control Min Mid Max Postions Notes Meets cULus requirements without the need of an electrical ground connection Actuators with appliance cables are numbered Actuators may be connected in parallel Power consumption and input impedance must be observed Actuators may also be powered by 24 VDC
16. of Bolts of Bolts Machine Bolts he el Sd 24 4 8 2E 3 7 94 6 24 4 ys 2 4 9 19 6 TE 24 8 ys 0 zx 10 15 46 8 T s 8 9 0 11 1 94 8 24 3 ANSI 250 Flange Detail for American Standard 250 Ib Cast Iron Pipe Flanges FLANGES DRILLING BOLTING Po Nominal A Flange B Flange F Diameter of C Diameter of D Diameter of Number Diameter E Length of Pipe Size Diameter Thickness Raised Face Bolt Circle Bolt Holes of Bolts of Bolts Machine Bolts o 1 4 19 e Sce Ya 8 91 SUE 3 87 1 51146 6 Ya 8 91 22 4 10 1 616 1 7 8 8 4 9 11 13 0 946 94 Va 8 91 4 6 12 20 17 46 SUAM 10 Ya 12 94 4 up A 01 14 Subject to change Belimo Aircontrols USA Inc WGVL G6 G7 Linkage with EV and RV Series Actuators Installation Instructions tly i n V n ftu 1I WS iF NS W a 4 UU TI VA cy OUI sjonuo Jry owog O eDueuo oj joelqns vL LO WGVL G6 G7 Linkage with EV Series Actuators W
17. ol Signal i 7 VDC mA 500 Q 1 4 watt Emis Default selectable 0 100 See Configuration Data Sheet Customizable See Configuration Data Sheet Override Control Min Mid Max Postions Wiring Diagrams Signal Direction Selector Switches Notes Meets cULus requirements without the need of an electrical ground connection Actuators with appliance cables are numbered Actuators may be connected in parallel Power consumption and input impedance must be observed Actuators may also be powered by 24 VDC Only connect common to neg leg of control circuits A 500 resistor converts the 4 to 20 mA control signal to 2 to 10 VDC Control signal may be pulsed from either the Hot Source or Common Sink 24 VAC line P PPPRPPO Contact closures A amp B also can be triacs A amp B should both be closed for the triac source and open for triac sink For triac sink the Common connection from the actuator must be connected to the Hot connection of the controller Position feedback cannot be used with a triac sink controller The actuator internal common reference is not compatible e O 5 _ c lt L IN4004 or IN4007 diode IN4007 supplied Belimo Part number 40155 Actuators with plenum rated cable do not have numbers on wires use color codes instead gt gt FP E Alaranjado Vermelho AT BELIMO WGVL G6 G7 Linkage with AVK Series Actuators Installati
18. on Instructions amp owog O oj joelqns 0 N 9 M J 1 EE CI LJ LO y Es S 10 AT BELIMO Electronic Fail Safe Actuator with 3 AAY 24 VAC Transformer Only Line Volts On Off 100 to 240 VAC Line N L1 Hot H L2 p On Off WGVL G6 G7 Linkage with AVK Series Actuators Wiring Diagrams 24 VAC Transformer s Line Volts ti Floating Point 100 to 240 VAC Line N L1 Hot H L2 Floating Point Selector Switches Signal Direction Fail Postion 4 E Fi Controller Triac Sink Electronic Fail Safe Actuator with MFT 24 VAC Transformer Line Volts 5 2 to 10 VDC Feedback Signal On Off 24 VAC Transformer Controller Triac Source 24 VAC Transformer Line Volts A Feedback Signal Direction of rotation switch Floating Point Triac Sink with Separate Transformer Notes 24 VAC Transformer Line Volis Control Signal VDC mA VDC 4to 20 mA 24 VAC Transformer AC Only Line Volts Control Signal m i C VDC mA 500 O 1 4 watt Ma
19. on power loss Spring Action Closed A to AB upon A to AB upon power loss Spring Action Closed A to AB upon lt AFB AFX MFT power loss power loss 2 3 oO e 2 GK Series NC FO Normally closed A to AB valve will open upon increase in signal Note To change valve to A to AB open reverse CW CCW switch Fail Position Will default fail A to AB open from the factory Fail position can be set from 0 100 in 1096 increments NO FC or NC FC Valve Can be open or closed will drive closed or open A to AB can be chosen with CW CCW switch Fail Position Will default fail A to AB open from the factory Fail position can be set from 0 100 in 1096 increments NO FO Normally open A to AB Fail Position Will default fail A to AB open from the factory Fail position can be set from 0 100 in 10 increments EV RV Series AFB AFX Series NC FO Normally closed A to AB valve will open upon increase in signal Note To change valve to A to AB open reverse CW CCW switch Fail Position Will default fail A to AB open from the factory Fail position can be set from 0 100 in 10 increments NO FC or NC FC Valve Can be open or closed will drive closed or open A to AB can be chosen with CW CCW switch Fail Position Will default fail A to AB open from the factory Fail position can be set from 0 100 in 10 increments NO FO Normally open
20. roller The actuator internal common reference is not compatible IN4004 or IN4007 diode IN4007 supplied Belimo Part number 40155 Actuators with plenum rated cable do not have numbers on wires use color codes instead Pb P PB Alaranjado Vermelho G6 G7 Globe Valves with Dual Mount GK X1 Actuators Wiring Diagrams PLA BELIMO Power Off Postion FC ro FC O POP POP On Off SR MFT 24V AC DC 24V AC DC FC FO Floating Point 24V AC DC 01 14 Subject to change Belimo Aircontrols USA Inc P d BELIMO G6 G7 Globe Valves with Single Mount AFX Actuators Installation Instructions ins N EA d J E A IGA A OUI sjonuo Jry owog eDueuo oj joelqns vL LO G6 G7 Globe Valves with Single Mount AFX Actuators Wiring Diagrams On Off Controller Spring Return Actuator with On Off Floating Point and SR E ci Spring Return Actuator with MFT 120 VAC 230 VAC Line Wht N Volts Bik H ade Function a 24 VAC up to 240 VAC Controller Line Volts Control Signal e 2 to 10 VDC x Feedback Signal VDC 4to 20 mA AT BELIMO 24 VAC Transformer VDC mA 24 VAC Transformer Controller 24 VAC Transformer Lin
21. tuators High Limit Control Wiring Multiple Actuators to a Series 90 Controller Typical Wiring Diagrams for Multiple using Minimum Position Potentiometer Actuators used with the W973 W7100 and T775 controllers Notes Actuators with plenum rated cable do not have numbers on wires use color codes instead Provide overload protection and disconnect as required Actuators and controller must have separate transformers Consult controller instruction data for more detailed information Resistor value depend on the type of controller and the number of actuators No resistor required for one actuator Honeywell resistor kits may be used To reverse control rotation use the reversing switch gt gt PPR 5 S lt Cinzento Alaranjado Vermelho AT BELIMO G6 G7 Globe Valves with Dual Mount AFX Actuators Installation Instructions gt amp owog O eDueuo oj joelqns 0 amp A O A v LNI w WS N AS B Jj AT BELIMO Spring Return Actuator with On Off Floating Point and SR On Off Spring Return Actuator with MFT Volts Controller G6 G7 Globe Valves with Dual Mount AFX Actuators Wiring Diagrams 120 VAC 230 VAC Line Wht N Volts Bik H ade
22. unction a On Off 24 VAC Transformer Controller Triac Source 24 VAC Transformer Line Volts 240 10 voc Feedback Signal 24 VAC Transformer Line Volts lo 500 Q C E 1 4 watt Control Signal VbC mA 9 IT VDC 4 to 20 mA Wht 3 Y4 Input 2 to 10V Default selectable 0 100 See Configuration Data Sheet Customizable See Configuration Data Sheet Override Control Min Mid Max Postions 24 VAC Transformer Controller Triac Sink with Separate Transformer 5 S lt Notes Meets cULus requirements without the need of an electrical ground connection Actuators with appliance cables are numbered Actuators may be connected in parallel Power consumption and input impedance must be observed Actuators may also be powered by 24 VDC Only connect common to neg leg of control circuits A500 resistor converts the 4 to 20 mA control signal to 2 to 10 VDC Control signal may be pulsed from either the Hot Source or Common Sink 24 VAC line gt Contact closures amp B also can be A amp B should both be closed for the triac source and open for triac sink For triac sink the Common connection from the actuator must be connected to the Hot connection of the controller Position feedback cannot be used with a triac sink cont
23. ws must be correct 5 Blow out all piping and throughly clean below valve installation 6 clean male pipe threads with wire brush and rag If threads have been damaged or exposed to weather running a tap or die over the threads may straighten them Clean pipes threads and valve threads before installation Check for any foreign material that can become lodged in trim components Strainers should be cleaned after initial startup 7 Pipe sealing compound may not be applied to either flange or gasket Flanged Globe Valves 212 to 6 Installation Instructions 8 Flanged bodies must be used with flanges which are rated for the service 125 Ib flanges have flat faces and may not be bolted to raised face flanges Gaskets rated for the medium and temperature pressure must be used 9 Valve must be installed with the stem towards the vertical not below the horizontal 10 Tighten bolts alternatively and evenly around the flange 11 2 way valve Normally Open NO or Normally Closed NC configurations must be verified by examining both the mechanical drawings and the valve and actuator 12 3 way valve Normally Open NO or Normally Closed NC configurations for the control port and the bypass port must be verified by examining both the mechanical drawings and the valve and actuator Check specifications for every application to be sure of ports and designations U L and C designations U is for Upper the control port
24. x Normal Default selectable 0 100 See Configuration Data Sheet Customizable See Configuration Data Sheet Override Control Min Mid Max Postions gt PPPRPO PPP 24 VAC Transformer Controller Anaranjado Meets cULus requirements without the need of an electrical ground connection Actuators with appliance cables are numbered Actuators may be connected in parallel Power consumption and input impedance must be observed Actuators may also be powered by 24 VDC Only connect common to neg leg of control circuits A 500 resistor converts the 4 to 20 mA control signal to 2 to 10 VDC Control signal may be pulsed from either the Hot Source or Common Sink 24 VAC line Contact closures A amp B also can be triacs A amp B should both be closed for the triac source and open for triac sink For triac sink the Common connection from the actuator must be connected to the Hot connection of the controller Position feedback cannot be used with a triac sink controller The actuator internal common reference is not compatible IN4004 or IN4007 diode IN4007 supplied Belimo Part number 40155 Actuators with plenum rated cable do not have numbers on wires use color codes instead 11 Alaranjado Vermelho G6 G7 Globe Valves with Dual Mount GK X1 Actuators Installation Instructions AT BELIMO N N H X g ARN S
Download Pdf Manuals
Related Search