concord ultimax.3
Contents
1. anchoring points and the safety display 07 is green y ALEA Turn the ISOFIX SYSTEM 08 control dial to the right until the CONCORD ULTIMAX lies as close flush as possible to the back rest of the car seat In vehicles with series standard headrests a readjustment of the headrest or its removal will allow a better mounting position of the car seat Please remember to readjust or replace the headrest in the correct position if an adult is to sit in that place instead Push the release button 09 outward and position the support leg 10 so that it rests securely on the floor and the safety display shows GREEN Release the control button 09 to lock the support leg in place CAUTION e he seat must be secured with the ISOFIX SYSTEM even if no child is travelling e Both ISOFIX adapters 15 must be locked securely in place and the safety displays 14 on both adapters must show green e he support leg 10 must rest securely on the floor and be locked into place _ SECURING YOUR CHILD IN THE CONCORD ULTIMAX CAUTION Check that the CONCORD ULTIMAX is mounted properly and that all belts have proper tension and also that all locking mechanisms are secure before each use At the front of the seat under the cover there is the central adjusting device 03 which clamps the central harness 04 tight Loosen the central adjusting device 03 by pushing the cap of the central adjusting device up2. and pull the harness forward do not pull on the harness cushioning I Pull the head rest control on the top edge upwards and move the head rest to the highest position 01 Open the harness lock 02 and move the harnesses to the sides and forward EST ES P SEN Sq Place your child as far back into the seat as possible Bring the shoulder lap harnesses and the central harness together in front of the child and close the harness lock Check that the harness lock 02 has latched shut correctly Ensure that none of the harness straps are twisted The CONCORD ULTIMAX must be adjusted to the size of the child Pull the head rest control on the top edge upwards and move the head rest 01 to the suitable position for your child The shoulder harness guide should be situated slightly above the child s shoulder The shoulder harnesses should lie in the middle between the child s neck and the outer edge of the shoulder am cu Tighten the harness by pulling the central harness 04 until it lies snug against the child s body CAUTION e he harnesses must not be twisted e he harness lock 02 must be closed properly and the harnesses must lie snug against the child s body e The headrest harness guide must be adjusted to the size of the child and latched securely in place 31 _ REMOVING THE CONCORD ULTIMAX USING THE TILT ADJUSTMENT To make the removal of the CONCORD ULTIMAX easi
3. any blanket warranty beyond 6 months for wear parts Please contact your specialist shop for baby and children s products and the relevant section of department stores your car accessory specialist shop or a catalogue company for replacement parts They will have a complete product portfolio for CONCORD child seat accessories to choose from The child seat CONCORD ULTIMAX has been tested in crash simulations for impacts of up to 50 km h against a solid obstacle Test results are compliant with the international test standard ECE R 44 04 which is applicable for all tested child safety seat systems When used as intended and in compliance with the installation and operating instructions the child safety seat should prevent or minimise injuries to children up to a body weight of 18 kg in case of an accident depending on the type and severity of accident e A child safety device does not replace responsible and careful behaviour in road traffic 21 OVERVIEW 01 Headrest 02 Harness buckle 03 Central adjusting device 04 Central harness 05 Operating lever for the tilt adjustment mechanism 06 Unlocking device for the seat lock with double switch 07 Safety display seat lock 08 ISOFIX SYSTEM control dial 09 Support leg operating button 10 Support leg 11 Front seat lock 12 Rear seat lock 13 ISOFIX SYSTEM unlocking button left and right 14 ISOFIX SYSTEM safety displays left and right 15 ISOFIX adapter
4. ION FROM 9 TO 18 KG SECURING YOUR CHILD IN THE CONCORD ULTIMAX REMOVING THE CONCORD ULTIMAX USING THE TILT ADJUSTMENT REMOVING ATTACHING THE COVER REMOVING THE PELVIC INSERT CARE INSTRUCTIONS WARRANTY CONDITIONS 19 IMPORTANT NOTES CAUTION Make sure you observe the relevant instructions in the user manual of your vehicle before transporting children Take particular note of all information provided for the use of child seats in connection with airbags WARNING e Children often carry small objects e g toys in jacket or trouser nerd and may also wear clothes with rigid components e g belt uckle Make sure that these objects are not clamped between the child and the safety harness as this might cause unnecessary injuries in case of an accident The same hazards also apply for adults e Naturally young children are often lively Make sure to explain the importance of safety when in a vehicle Your child will then understand that the harness lock should not be opened and the harness should not be moved giving you more peace of mind e Your child s safety can only be guaranteed if the safety system is installed and used in accordance with the instruction manual e All system harness straps must be worn taut and without any twists and must be protected from damage e Protect any parts of the restraint system not covered with fabric against direct sunlight to prevent your child from suffering burns e Ihe c
5. USING THE CONCORD ULTIMAX CHILD CAR SEAT With the safety of your child in mind you have decided to purchase our car seat CONCORD ULTIMAX The product is manufactured under strict quality control conditions Its optimum safety characteristics are only effective if the seat it used as intended As a result you should ensure strict adherence with the mounting and usage instructions The CONCORD ULTIMAX is suitable for children up to the age of approx 4 or up to 18 kg It is suitable for use in vehicles with ISOFIX approved seats see documentation contained in the vehicle s operating manual in accordance with the relevant child restraint and anchoring category As a result of accident statistics however we recommend using the seat behind the front passenger seat The seat consists of 2 parts the seat and ISOFIX base B 22 _ GENERAL INFORMATION e his is an ISOFIX child restraint It has been approved for general use in vehicles equipped with ISOFIX anchoring systems in compliance with ECE regulation 44 change series 04 It is suitable for use in vehicles with ISOFIX approved seats see documentation contained in the vehicle s operating manual in accordance with the relevant child restraint and anchoring category e his child safety restraint is compliant with the ISOFIX weight category up to 18 kg and ISOFIX size categories D and A If you have any questions or doubts please contact the manufacturer of the child safety
6. _ DEUTSCH ENGLISH _ FRANCAIS _ ESPANOL _ ITALIANO _ PORTUGUES _ NEDERLANDS _ NORSK _ DANSK _ SUOMI Concord GmbH Industriestra e 25 95346 Stadtsteinach Germany Phone 49 0 9225 9550 0 Fax 49 0 9225 9550 55 info concord de www concord de Einbau und Bedienungsanleitung Instructions for attachment and use Directives d installation et mode d emploi Instrucciones de montaje y de uso Istruzioni per l uso e il montaggio Manual de montagem e de utilizac o Inbouw en bedieningshandleiding Bruksanvisning og monteringsveiledning Monterings og betjeningsvejledning Kiinnitys ja k ytt ohjeet Y N T Y N LO 2 gt MORD ULTIMAX 3 DEUTSCH ENGLISH FRAN AIS ESPA OL ITALIANO PORTUGU S NEDERLANDS NORSK DANSK SUOMI Kindergewicht child s weight ca Alter approx age ECE Gruppen ECE groups ISOFIX Gruppen ISOFIX groups Y 0 18 kg 0 18 kg 0 4 Jahre 0 4 years 0 und 0 and D und A D and A Se 9 Norm ECE R44 04 e rd standard ECE R44 04 v d norme ECE R44 04 s U N norma ECE R44 04 szabvany ECE R44 04 _ ENGLISH IMPORTANT NOTES OVERVIEW USING THE ULTIMAX CHILD CAR SEAT GENERAL GUIDELINES FOR ISOFIX SUITABLE VEHICLES REMOVING THE SEAT MOUNTING THE CONCORD ULTIMAX MOUNTING THE SEAT OPPOSITE TO THE DRIVING DIRECTION FROM BIRTH TO 13 KG MOUNTING THE SEAT IN THE DRIVING DIRECT
7. d support 01 _ CARE INSTRUCTIONS Thread the harness lock 02 through the harness lock cushioning and out underneath the cover Light dirt can be easily removed with a damp cloth The cover can also be removed and washed at 30 C Remove the back cushion from the cover of the head support before you wash it Open the Velcro fastener on the harness guides and remove the cover from the seat The cover material colour may run slightly when wet in particular during washing The covers are attached in reverse order XX K ej Do not use solvents on the cover Check that all the locks are closed and all anchorings are correctly fastened 34 35 _ WARRANTY CONDITIONS The warranty period begins at the time of purchase The warranty period granted is compliant with the legal warranty period in the country of purchase In terms of content the warranty covers rework replacement delivery or a rebate as the manufacturer sees fit The warranty applies only for the original user In case of a fault warranty rights will be applicable only if the dealer where the item was purchased is notified immediately after initial detection Should the dealer be unable to remedy the issue then the product will be returned to the manufacturer with a detailed description of the fault and with the official purchase document including the date of purchase The manufacturer shall not accept liability for faulty products not delivered by hi
8. eds 8 kg the pre installed pelvic insert should be removed see REMOVING THE PELVIC INSERT y AB Turn the ISOFIX SYSTEM 08 control dial to the right until the CONCORD ULTIMAX lies as close flush as possible to the back rest of the car seat Push the release button 09 outward and position the support leg 10 so that it rests securely on the floor and the safety display shows GREEN Release the control button 09 to lock the support leg in place CAUTION e he seat must be secured with the ISOFIX SYSTEM even if no child is travelling Both ISOFIX adapters 15 must be locked securely in place and the safety displays 14 on both adapters must show green The support leg 10 must rest securely on the floor and be locked into place MOUNTING THE SEAT IN THE DRIVING DIRECTION FROM 9 18 KG CAUTION Mounting in the driving direction is only permitted for babies which weigh more that 9 kg and without the pelvic insert see REMOVING THE PELVIC INSERT Always mount the seat without a child in it Guide the seat A as show in the driving direction over the base B First mount the frame of the seat into the rear seat lock 12 of the ISOFIX base Then fold the seat forward until the front seat lock 11 audibly locks into the ISOFIX base and the safety display 07 on the top is green CAUTION gt ne e Make sure that the seat is correctly MIS anchored to both
9. er we recommend you first Move the tilt adjustment operating lever 05 at the front of the seat upwards and remove the seat A see REMOVING THE SEAT bring the seat into the desired position Always mount and remove the CONCORD ULTIMAX without a child in it By releasing the lever 05 the seat is locked Push the release button 09 outward and move the support leg 10 into its top most position y ALEA Turn the ISOFIX SYSTEM 08 PS control dial on the front of the CONCORD ULTIMAX ISOFIX base to the left and move the base forward Push the ISOFIX SYSTEM unlocking buttons 13 on the left and right of the base so that the ISOFIX adapters 15 are released from the receptacles and the base springs forward Lift the CONCORD ULTIMAX out of the car seat Turn the ISOFIX SYSTEM 08 control dial to the right until the ISOFIX adapter 15 is fully extended gt gt gt 32 33 _ REMOVING ATTACHING THE COVER _ REMOVING THE PELVIC INSERT To remove the cover the seat A has to be removed from the base B see REMOVING THE SEAT If the child s bodyweight exceeds 8 kg the pre mounted pelvic insert should be removed This can be found in a pocket under the seat on the reverse of the seat cover Loosen the rubber bands and push buttons of the cover which are located in the places marked red on the reverse side of the cover Open the harness lock 02 First remove the cover from the hea
10. et belangrijk dat u bij de bestelling in uw speciaalzaak onderstaande gegevens vermeldt N Bilbarnesetet som du kj pte skal fungere riktig og gi optimal sikring ogs etter at reservedeler eller tilbeh r er byttet ut Ved eventuelle bestillinger bervi deg derfor om gi forhandleren folgende opplysninger DK For at garantere at autostolen stadig er funktionsdygtig og sikker ogs efter at der er blevet monteret reservedele eller tilbeh r bedes De oplyse f lgende til Deres forhandler ved bestillingen FIN Lasten turvaistuimen toiminnan ja turvallisen k yt n varmistamiseksi my s varaosien tai lis varusteiden asennuksen j lkeen anna j lleenmyyj lle seuraavat tiedot kun tilaat osia CONCORD N ECE IndustriestraBe 25 95346 Stadtsteinach ECE nr Made in Germany ECE nr ECE nr semiuniversal ECE nro O 0 18 kg N de s rie Serie nr Serienr D 04 Serienr Era 2 0000000000 Pe a Type kinderzitje Reservedel Reservedel Varaosa Loja especializada Speciaalzaak Forhandler Forhandler J lleenmyyj Meu endere o Mijn adres Min adresse Min adresse Oma osoite
11. hild restraint system must not be damaged or crushed by moving parts in the vehicle or by the vehicle doors e Do not attempt any modifications to the restraint system as they might endanger your child s safety e After an accident the entire child restraint system must be replaced or sent to the manufacturer for testing along with an accident report e Make sure to instruct your passenger on how to remove the child from its safety seat in case of an accident or danger e Ihe lap belts of the harness system must be fitted as low down as possible so that the child s hips are held correctly e The child seat must not be used on seats with activated front airbags Danger to life 20 e Never leave your child unsupervised in the car seat whether harnessed or not e Make sure you secure any luggage and loose items to reduce the risk of injury in case of an accident e he manual must always be carried with the child safety seat e Ihe use of any accessories or replacement parts is prohibited and non compliance will result in the lapse of all warranty and liability claims This only excludes original accessories from CONCORD The child safety seat is to be used with original seat covers only If the restraint system is used extensively it is normal for the seat covers and other parts to suffer varying degrees of wear depending on the duration and intensity of use and they will then have to be replaced We can therefore not provide
12. m Warranty claims are void if e the product was modified e the product is not returned complete and accompanied by the original purchase document to the dealer within 14 days of the detection of the fault e the fault occurred due to inappropriate handling or maintenance or due to other actions that are the fault of the user specifically where the user instructions were not complied with e epairs on the product were carried out by third parties e the defect was caused by an accident e the serial number has been damaged or removed Modifications to or deterioration of the product caused by the contractually agreed use of the item normal wear and tear will not be accepted as a warranty claim Any services rendered by the manufacturer in case of a warranty claim shall not extend the warranty period 36 concer ULTIMAX 3 D Um die Funktionsf higkeit und Sicherheit Ihres Kinderautositzes auch nach dem Austausch von Ersatz und Zubeh rteilen zu gew hrleisten bitten wir Sie bei Bestellungen Ihrem Fachh ndler nachstehende Angaben mitzuteilen EN To ensure the functionality and safety of your child s car seat after replacing spare and accessory parts please provide your dealer with the following details when placing your order F Dans le but d assurer le bon fonctionnement et la s curit de votre si ge auto enfant galement en cas de remplacement de pi ces de rechange et accessoires nous vous prions de bien v
13. ouloir en cas de commande donner les renseignements suivants votre revendeur E A Para seguir garantizando el correcto funcionamiento y la seguridad de su asiento para ni os despu s del cambio de piezas o accesorios le rogamos que indique los siguientes datos al realizar pedidos a su comercio especializado Quando trasmette un ordine al Suo rivenditore di fiducia La preghiamo di comunicargli i dati seguenti per garantire la funzionalit e la sicurezza del Suo seggiolino per bambini anche dopo la sostituzione di parti di ricambio e di accessori CONCORD ECE Nr Industriestra e 25 ECE No 95346 Stadtsteinach N ECE Made in Germany N mero ECE semiuniversal VE DI 0 18 kg Serien Nr Serial No N de s rie D 04 N mero de serie Mdsere DI 2 0000000000 Ersatzteil Spare part Type de si ge Pieza de repuesto Parte di ricambio Fachh ndler Dealer Revendeur Comercio especializado Rivenditore specializzato Meine Anschrift My address Mon adresse Mi direcci n Il mio indirizzo coneork ULTIMAX 3 P Para garantir a funcionalidade e a seguranca da cadeira de crianca para autom vel depois da substituic o de pecas sobressalentes e de acess rios agradecemos o fornecimento dos dados seguintes loja especializada aquando de encomendas NL Om de functionaliteit en de veiligheid van het door u gekochte autokinderzitje ook na vervanging van onderdelen en accessoires te waarborgen is h
14. unit or your retailer FOR ISOFIX SUITABLE VEHICLES The CONCORD ULTIMAX with ISOFIX system has been approved for semi universal use and is suitable for mounting on specific vehicle seats The appendix CAR FITTING LIST contains an overview of vehicles and vehicle seats that have been approved for using the CONCORD ULTIMAX with ISOFIX system in connection with a support leg Should your vehicle not be listed please ensure that the CONCORD ULTIMAX can be properly mounted in your car on the desired seat before you purchase the child seat Read the user manual provided by the manufacturer of your vehicle and the mounting and security instructions contained in this user manual For latest updates please visit www concord de 23 _ REMOVING THE SEAT The seat A of the CONCORD ULTIMAX can be removed from the ISOFIX Basis B Always remove the child first before removing the seat Move the tilt adjustment operating lever 05 at the front of the seat upwards and bring the seat into an upright position The unlocking mechanism of the seat lock 06 is at the front underneath the seat on the top of the ISOFIX base Pull the upper part of the lock 06 forwards and push the lock down Lift the seat up off the base 24 MOUNTING THE CONCORD ULTIMAX To make mounting easier we recommend removing the seat A of the CONCORD ULTIMAX from the base B see REMOVING THE SEAT Always mo
15. unt and remove the CONCORD ULTIMAX without a child in it y Hs Turn the ISOFIX SYSTEM 08 control dial on the front of the CONCORD ULTIMAX ISOFIX base to the left until the ISOFIX adapter 15 on the E reverse is fully extended Place the base in the direction of driving on a vehicle seat equipped with ISOFIX receptacles D Push the child seat backwards onto the ISOFIX receptacles until are green Now reinsert the seat depending on the age of the child either in the driving the locking mechanisms of both ISOFIX adapters 15 audibly lock into place and the safety displays 14 on both sides of the base direction or opposite to it see MOUNTING THE SEAT OPPOSITE TO THE DRIVING DIRECTION FROM BIRTH TO 13 KG or MOUNTING THE SEAT IN THE DRIVING DIRECTION FROM 9 18 KG MOUNTING THE SEAT OPPOSITE TO THE DRIVING DIRECTION FROM BIRTH TO 13 KG CAUTION Do not use on seats with airbags Danger to life Always mount the seat without a child in it Guide the seat A as shown opposite to the driving direction over the base B First mount the frame of the seat into the seat lock 12 of the ISOFIX base Then fold the seat forward until the front seat lock 11 audibly locks into the ISOFIX base and the safety display 07 on the top is green CAUTION e Make sure that the seat is correctly anchored to both anchoring points and the safety display 07 is green e f the child s bodyweight exce
Download Pdf Manuals
Related Search