User manual
Contents
1. NEVER DISCONNECT THE PLUG BY PULLING ON THE POWER SUPPLY LEAD IMMEDIATELY AFTER INSTALLATION CARRY OUT A QUICK TEST ON THE HOB FOLLOWING THE INSTRUCTIONS PROVIDED LATER IN THIS MANUAL IF THE APPLIANCE FAILS TO OPERATE DISCONNECT IT FROM THE ELECTRICAL MAINS AND CONTACT YOUR NEAREST SERVICE CENTRE NEVER ATTEMPT TO REPAIR THE APPLIANCE YOURSELF AFTER EACH USE OF THE HOB ALWAYS CHECK THAT THE CONTROL KNOBS ARE TURNED TO ZERO OFF NEVER PLACE PANS WITH BOTTOMS WHICH ARE NOT PERFECTLY FLAT AND SMOOTH ON THE HOB PAN STANDS NEVER USE PANS OR GRIDDLE PLATES WHICH PROJECT BEYOND THE OUTSIDE EDGE OF THE HOB THE NAMEPLATE WITH THE TECHNICAL DATA SERIAL NUMBER AND MARK IS IN A VISIBLE POSITION UNDERNEATH THE CASING ANNEXED TO THIS MANUAL AND APPLIED TO THE QUALITY CERTIFICATE THIS NAMEPLATE MUST NEVER BE REMOVED THE APPLIANCE IS INTENDED FOR USE BY ADULTS KEEP CHILDREN AT A SAFE DISTANCE AND NEVER ALLOW THEM TO PLAY WITH IT THIS APPLIANCE IS TAGGED UNDER EUROPEAN DIRECTIVE 2002 96 EC ON WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT WEEE THIS DIRECTIVE CONTAINS THE REGULATIONS GOVERNING THE COLLECTION AND RECYCLING OF DECOMMISSIONED APPLIANCES THROUGHOUT THE EUROPEAN UNION The manufacturer declines all responsibility for injury or damage caused by failure to comply with the above regulations or deriving from tampering with even just one part of the appliance and the use of non original spare parts v D Instructions for2. cooking processes in particular a window should be opened or the speed of any fans increased after prolonged use 4 3 Combustion gas discharge Combustion gases must be discharged by means of hoods connected to a flue with reliable natural draught or a fan extraction system An effective extraction system requires careful design by an authorised specialist and must comply with the regulation distances and positions After installation the engineer must issue a certificate of compliance 27 Instructions for the Installer 5 Adapting to different types of gas The operations described below must be carried out with the appliance not built in and not connected to the gas or electricity supply The appliance is tested with G20 2H natural gas at the pressure of 20 mbar If it is to be used with other types of gas the burner nozzles have to be changed and the primary air flow adjusted To replace the nozzles and adjust the burners the hob skin has to be removed Proceed as described below 5 1 Removing the hob skin Remove all the burner components in the numerical order shown below e Pull off all the knobs e Lift all the burner components off the hob 1 e Remove the cover plate of each burner by undoing the screws 2 e Remove the hob skin fixing screws taking care only to remove the screws shown on the right 3 e After removing all the components described above lift off the hob skin 28 Inst
3. Contents 1 Precautions for safety and use 22 2 Fitting the appliance in the top 23 2 1 Fixing to the supporting structure 23 2 2 Fitting the adhesive foam rubber strip 24 2 3 Fitting the fixing clips 24 2 4 Fitting the hob into the hole in the work top 24 2 5 Additional fixing using brackets 25 3 Electrical connection 26 4 Gas connection 27 4 1 Bottled gas connection 27 4 2 Room ventilation 27 4 3 Combustion gas discharge 27 5 Adapting to different types of gas 28 5 1 Removing the hob skin 28 5 2 Adjusting for bottled gas 29 5 3 Adjusting for natural gas 29 5 4 Adjusting the primary air flow 30 5 5 Reassembling the hob skin 31 5 6 Adjusting the minimum setting for natural ga 31 5 7 Adjusting the minimum for bottled gas 31 5 8 Hob burner layout 31 5 9 Greasing the gas taps 31 6 Description of controls 32 6 1 The front panel 32 7 Using the hob 33 7 1 Fitting the pan stands 33 7 2 Lighting burners with safety device 36 7 3 Positioning the griddle plate 36 7 4 Practical hints for using the burners 36 7 5 Pan diameters 37 8 Cleaning and maintenance 38 8 1 Cleaning the hob 38 8 2 Cleaning the components 38 THESE INSTRUCTIONS ONLY APPLY TO THE COUNTRIES OF DESTINATION WHOSE IDENTIFICATION SYMBOLS ARE LISTED ON THE COVER OF THIS MANUAL THIS BUILT IN HOB IS CLASSIFIED AS CLASS 3 INSTRUCTIONS FOR THE INSTALLER these are intended for the qualified engineer who is to check the gas supply system and install commission and test the a
4. aller 5 4 Adjusting the primary air flow Refers to the gap X in mm BUNNER Men Precast a Auxiliary 0 5 9 5 Semi rapid 1 1 Rapid 2 3 Ultra Rapid 4 open To identify the burners on your hob refer to the drawings in point 5 8 Hob burner layout 30 Instructions for the Installer pace 5 5 Reassembling the hob skin Reverse the procedure described in point 5 1 Removing the hob skin of When replacing the cover plates check that the seals are fitted correctly Fit the pan stands as described in point 7 1Fitting the pan stands 5 6 Adjusting the minimum setting for natural ga Reassemble the components on the burner and fit the knobs onto the tap rods Light the burner and turn it to the minimum setting Remove the knob again and adjust the regulator screw inside or beside the tap rod depending on the model until an even minimum flame is obtained Put the knob back in place and check the stability of the burner flame the flame must not go out when the knob is turned quickly from the maximum to the minimum setting 5 7 Adjusting the minimum for bottled gas To adjust the minimum level when using bottled gas the adjuster screw inside or beside the tap rod must be turned fully clockwise depending on the models The diameters of the bypasses for each individual burner are stated in point 5 2 Adjusting for bottled gas Si After adjusting for use of a gas other than the gas used for te
5. connection has an external 1 2 gas thread ISO 228 1 Connection with copper pipe The connection to the gas supply mains must be made so that no stresses or strains of any kind are applied to the appliance The connection can be made using the adapter unit D with two conical elements always fitting the gasket C supplied Connection with steel hose use only continuous wall stainless steel hoses compliant with the relevant regulations and always fit the gasket C supplied between the fitting A and the hose E When connecting with a hose ensure that the total length of the pipeline is not more than 2 metres also ensure that the hoses do not touch moving parts and are not crushed 4 1 Bottled gas connection Use a pressure regulator and make the connection to the gas cylinder in accordance with the relevant regulations Make sure that the gas supply pressure is as stated in the table in point 5 2 Adjusting for bottled gas 4 2 Room ventilation The appliance may only be installed in a permanently ventilated room as specified by the relevant regulations The air flow into the room where the appliance is installed must be sufficient for proper gas combustion and room ventilation The air intakes protected by gratings must be of suitable size see relevant regulations and located so that they cannot be even partially obstructed The kitchen must be kept properly ventilated to disperse the heat and humidity produced by
6. e brackets provided can be used in addition to the clips They act as an additional connection between the hob and the work top into which it is built To fix screw the brackets A into place using the screw provided See right for the precise holes to be used when securing the hob to the top correctly using the brackets 25 X Instructions for the Installer 3 Electrical connection Check that the power supply line voltage and size are as specified on the nameplate underneath the appliance s casing This nameplate must never be removed The plug on the end of the power supply lead and the wall socket must be of the same type and comply with the relevant regulations Check that the power supply line is properly earthed Pass the power supply cable through the rear of the cabinet taking care that it does not touch the bottom case of the hob or the oven if any built in underneath it a The appliance s power supply line must be fitted with an omnipolar breaking device with ay contact gap of at least 3 mm located in an easily accessible position close to the appliance itself The use of reductions adapters or junctions is not recommended If the power supply cable has to be replaced the gauge of the wires in the new cable must be at least 0 75 mm 3 x 0 75 cable bearing in mind that the earth wire yellow green must be at least 20 mm longer at the end for connection to the appliance Use only a t
7. equently and if necessary clean them with a wet cloth Remove any dry residues with a wooden toothpick or a needle
8. es C in the burner must mate with the ignition plugs and thermocouples D on the hob 7 1 Fitting the pan stands The pan stands are supplied dismantled from the hob To place each pan stand on its burner correctly follow the instructions provided below The ends of the feet of each pan stand carry silicone rubber pads with holes which must be fitted onto the fixing pins provided on the hob 33 To fit the pan stand first align it with the fixing pin 1 and then lower it into place on the hob taking care that it fits over the flame diffuser ring correctly 2 Instructions for the User Each pan stand will only fit onto its own burner To ensure correct positioning each pan stand has a different recess as shown here which will fit over the projection on the corresponding flame diffuser ring Take great care to fit the correct pan stand on each burner After the pan stand is fitted its feet must rest on the hob and not be suspended above it Make sure that the pan stands are simply fitted over their burners and are not left in a raised or tilted position if this occurs repeat the fitting procedure x WRONG 34 RIGHT A Instructions for the User ome After performing the operations described above for each pan stand the hob will be as shown below with the feet of the pan stand
9. itting the adhesive foam eee strip Fit the adhesive foam rubber strip Supplied with the hob around the outside edge of its surround It will act as a cushion between the surface of the surround and that of the cabinet The diagram on the right shows the correct position for the foam rubber strip Take great care when fitting it to ensure that it does not project beyond the outside edge of the frame 2 3 Fitting the fixing clips Fit the fixing clips in all the points marked with an arrow The clips fix the hob an ensure that it is centred correctly To fit the clips to the hob simply press them gently horizontally into the groove provided fig A Then turn them upwards to fix them permanently in place fig B 2 4 Fitting the hob into the hole in the work top Take special care when fitting the hob into the work top If the procedures are not carried out correctly exactly as described the hob may be damaged Before fitting the hob remove the pan stands if fitted and the A burners from the hob 4 When fitting the hob first rest the surround entirely on the back a edge of the hole in the work top Do not apply leverage to the surround since this part is very delicate there is a risk of damaging it Then lower the front of the hob until the appliance is completely in place TA 24 Instructions for the Installer 2 5 Additional fixing using brackets For even more secure fixing th
10. positioned the knobs may overheat while it is in use 7 4 Practical hints for using the burners For better burner efficiency and to minimise gas consumption use flat even bottomed pans with lids of suitable size for the burner see point 7 3 Pan Diameters T When cooking to prevent burns or damage to the hob all pans or griddle plates must be placed inside the perimeter of the hob and must be at least 5 7 cm from the knobs ull ill al 6 5 7 cm Instructions for the User we 7 5 Pan diameters BURNERS min and max in cm 1 Auxiliary 7 18 2 Semi rapid 10 24 3 Rapid 18 24 4 Ultra Rapid 20 28 37 A 3 LEA Instructions for the User 8 Cleaning and maintenance Before carrying out any operations disconnect the appliance from the electricity supply Never use a jet of steam for cleaning the appliance 8 1 Cleaning the hob To keep the hob in good condition it must be cleaned regularly after each use first allowing it to cool 8 1 1 Routine daily glass hob cleaning When cleaning and caring for glass surfaces always use only specific products which do not contain abrasives or chlorine based acids Instructions for use pour the product onto a damp cloth and wipe over the surface then rinse thoroughly and dry with a soft cloth or chamois leather 8 1 2 Food stains or spills Never use metal scouring pads or sharp scrapers which will damage the su
11. ppliance description of the controls and the correct procedures for cleaning and maintaining the me INSTRUCTIONS FOR THE USER these provide recommendations for use a appliance 21 T 1A U 2 22 Precautions for Safety and Use 1 Precautions for safety and use THIS MANUAL IS AN INTEGRAL PART OF THE APPLIANCE TAKE GOOD CARE OF IT AND KEEP IT TO HAND THROUGHOUT THE HOB S LIFE CYCLE USERS ARE ADVISED TO READ THIS MANUAL AND ALL THE INSTRUCTIONS IT CONTAINS BEFORE USING THE HOB ALSO KEEP THE SET OF NOZZLES PROVIDED IN A SAFE PLACE INSTALLATION MUST BE CARRIED OUT BY QUALIFIED STAFF IN COMPLIANCE WITH THE RELEVANT REGULATIONS THIS APPLIANCE IS INTENDED FOR HOUSEHOLD USE AND COMPLIES WITH THE EEC DIRECTIVES CURRENTLY IN FORCE THE APPLIANCE IS BUILT TO PROVIDE THE FOLLOWING FUNCTION COOKING AND HEATING FOODS ALL OTHER USES ARE TO BE CONSIDERED IMPROPER THE MANUFACTURER DECLINES ALL LIABILITY FOR USES OTHER THAN THOSE STATED ABOVE NEVER LEAVE PACKAGING RESIDUES UNATTENDED IN THE HOME SEPARATE WASTE PACKAGING MATERIALS BY TYPE AND CONSIGN THEM TO THE NEAREST SEPARATE DISPOSAL CENTRE THE APPLIANCE MUST BE CONNECTED TO EARTH IN COMPLIANCE WITH ELECTRICAL SYSTEM SAFETY REGULATIONS THE PLUG TO BE CONNECTED TO THE POWER SUPPLY LEAD AND THE RELATIVE SOCKET MUST BE OF THE SAME TYPE AND COMPLY WITH THE RELEVANT REGULATIONS THE POWER SUPPLY SOCKET MUST BE ACCESSIBLE EVEN AFTER THE APPLIANCE HAS BEEN BUILT IN
12. rface Use ordinary non abrasive products for glass with the aid of non scratching sponges and wooden or plastic utensils if necessary Rinse thoroughly and dry with a soft cloth or chamois leather CU 8 2 Cleaning the components Never clean the knobs with aggressive products containing alcohol or steel or glass cleaners since they might cause permanent damage NEVER REMOVE THE FIXING COVER PLATES TO CLEAN THE HOB The components described below must never be washed in a dishwasher 8 2 1 The knobs The knobs must be cleaned with a soft cloth dipped in warm water and dried thoroughly They can easily be lifted off 8 2 2 The pan stands Remove the pan stands and wash them in warm water with a non abrasive detergent taking care to remove all deposits Replace them on the hob following the instructions provided in point 7 1Fitting the pan stands 8 2 3 The flame diffuser rings The burner caps and flame diffuser rings can be removed for easier cleaning wash them in hot water and non abrasive detergent taking care to remove all deposits and wait for them to dry completely The burner pins A must be fitted into the recesses B in the flame diffuser ring The holes C in the flame diffuser ring must mate with the ignition plugs and thermocouples 38 D on the hob 8 2 4 The plugs and thermocouples For best performance the ignition plugs and thermocouples must always be kept thoroughly clean Check them fr
13. ructions for the Installer 5 2 Adjusting for bottled gas Undo the screw C and push the air regulator D fully down Remove the nozzle E with a 7 mm spanner and fit the suitable one following the instructions in the tables referring to the type of gas to be used The nozzle must not be tightened with a torque of more than 3 Nm Regulate the air flow by sliding the regulator D along until the distance X stated in point 5 5 Adjusting the primary air flow is obtained Fix the regulator D by tightening the screw C Rated Burner heat Bottled gas G30 G31 30 37 mbar capacity kW Nozzle By pass Reduced Flow Flow diameter mm heat rate g h rate g h 1 100 mm 1 100 capacity G30 G31 W Auxiliary 1 05 48 30 400 76 75 Semi rapid T7 62 32 450 124 121 Rapid 3 0 80 50 1050 218 214 Ultra Rapid 5 0 108 63 1600 363 357 5 3 Adjusting for natural gas The appliance is tested with G20 2H natural gas at the pressure of 20 mbar To return the appliance to the condition required to use this type of gas proceed as described in point 5 2 Adjusting for bottled gas but select the nozzles and adjust the primary air flow for natural gas as indicated in the table below and in point 5 5 Adjusting the primary air flow Burner eae Natural gas G20 20 mbar Nozzle diameter Reduced heat capacity 1 100 mm W Auxiliary 1 05 73 400 Semi rapid 1 7 92 450 Rapid 3 0 123 1050 Ultra Rapid 5 0 165 1400 29 Instructions for the Inst
14. s forming a pattern of horizontal and vertical lines If a pan wobbles noticeably check that the pan stands have not been fitted incorrectly 35 36 Instructions for the User 7 2 Lighting burners with safety device The burner it controls is shown next to each knob the example here shows the front left hand burner The appliance is equipped with electronic ignition Simply press the knob and turn it anti clockwise to the minimum flame symbol Lh until the burner lights Keep the knob pressed down for about 2 seconds to keep the flame alight and prime the safety device The burner may go out when the knob is released In this case repeat the operation keeping the knob pressed down for longer When the burner has lit its control knob will light up to confirm that it is in operation The knob will go out a few seconds after it is turned to the O position or if the burner goes out accidentally The knob light comes on and goes out gradually If the burners should go out accidentally the safety device will be tripped about 20 seconds later cutting off the gas supply even if the gas tap is open 7 3 Positioning the griddle plate A special griddle plate for use with the hob is available from authorised dealers This plate must be PLACED ON THE PAN STANDS PROPERLY CENTRED It must never be fitted instead of a pan stand Ensure that the griddle plate is properly centred on the pan stands if it is not correctly
15. sting the appliance fy replace the label on the casing with the label for the new gas The label is supplied in SEE the bag with the LPG nozzles G30 G31 5 8 Hob burner layout Burner type 1 Auxiliary 2 Semi rapid 3 Rapid 4 Ultra rapid 0000 5 9 Greasing the gas taps Over time the gas taps may become stiff or jam Clean their insides and change their gt lubricating grease This operation must be carried out by a skilled technician 31 g Instructions for the User 6 Description of controls 6 1 The front panel All the hob s control and monitoring devices are placed together on the front panel CONTROL AREA OOOO 5 Burner Hob KNOB OPERATING MODE To light the flame press the knob and at the same time turn it anti clockwise to the minimum flame symbol To adjust the flame turn the knob to the zone between the maximum NY and the minimum settings To turn off the burner turn the knob back to the O position BURNER LAYOUT Key to symbols oO Front left hand burner E Rear left hand burner C Middle burner O Rear right hand burner o Front right hand burner 32 Instructions for the User 7 Using the hob Check that the fixing cover plates E the burners the flame diffuser rings and the pan stands are fitted correctly The projections A on the flame diffuser rings must be fitted into the recesses B in the burner The hol
16. the Installer 2 Fitting the appliance in the top If the hob has to be adapted for a type of gas different from the one for which it is preset in the factory make this adjusting before building it into the unit following the instructions in point 5 Adapting to different types of gas The procedures required below must be carried out by a skilled builder and or joiner The hob can be installed on various materials including masonry metal solid wood and wood finished with plastic laminates provided the material is heat resistant T 90 C 2 1 Fixing to the supporting structure Make a hole in the cabinet top with the dimensions shown here maintaining a distance of at least 50 mm from the rear edge This appliance may be installed against walls higher than the worktop surface provided the distance shown here is maintained in order to prevent damage due to overheating Make sure that there is at least 750 mm between the hob burners and a shelf or hood if any placed vertically above them If the hob is installed above an oven the oven must be fitted with a cooling fan If the hob is installed above a cupboard with doors a separator panel must be installed underneath it Leave a gap of at least 10 mm between the bottom of the hob and the surface of the panel which must be easily removable to allow sufficient access for any servicing procedures 23 N l gt Instructions for the Installer 2 2 F
17. ype HO5V2V2 F or similar cable resistant to a temperature of up to 90 C The cable must be replaced by a qualified electrician who must make the mains connection as shown below f 20 mm L brown N blue yellow green The power supply lead must be replaced by an authorised service centre to prevent all risks The manufacturer declines all responsibility for injury or damage caused by failure to comply with the above regulations or deriving from tampering with even just one part of the appliance gt gt 26 Instructions for the Installer xX 4 Gas connection If the appliance is installed above an oven the gas hose must be passed around the back of the oven to prevent overheating The connection to the gas mains may be made using a copper pipe or a continuous wall steel hose in accordance with the relevant regulations To simplify connection the horizontal position of the fitting A on the back of the appliance is adjustable Undo the hexagonal nut B turn the fitting A into the required position and re tighten the hexagonal nut B it has a rubber gasket to ensure it provides an effective seal When installation is complete check for any leaks with a soapy solution never with a naked light The appliance is tested with G20 2H natural gas at the pressure of 20 mbar For use with other types of gas see point 5 ADAPTING TO DIFFERENT TYPES OF GAS The gas intake
Download Pdf Manuals
Related Search