Vivaldi Transport User Manual v1.0x
Contents
1. The pin connections are Pin 2 dCS unit transmit Pin 3 dCS unit receive Pin5 ground Shell cable screen amp drain wire J J We recommend using infra red remote control instead Mains inlet Power is connected via a standard IEC320 connector S protected by a fuse and isolated by a 2 pole power switch Label The label T states the unit s serial number and the nominal voltage to which the unit is set It is important to quote the serial number if you need assistance Vivaldi Transport Manual v1_0x docx English version dCS Vivaldi Transport User Manual THE MENU Displays the unit status Selects the format for playing hybrid discs CD SACD gt Sets the display brightness Signal Generator Outputs tone on L channel only then R channel only Vivaldi Transport Manual v1_0x docx outputs on off Brightness gt Software Issue 1 0x August 2012 Displays the software Displays dCS Loads new software from a dCS CD issues amp serial contact details number Factory Reset Restores standard factory settings Selects DSD or DXD Select RS232 upsampling on Text Mode or AES1 2 for Binary Mode CD data Display On Off Turns the main display on off Outputs Noise on both modulated pink channels then noise to burn inverts R in your system Figure 6 The menu sequence English version dCS Vivaldi Transport U2. e Copy protected discs that do not conform to the Red Book CD standard may not play correctly or may not play at all Such discs are not CDs they are optical discs that have been recorded with digital audio data They should not carry the Compact Disc Digital Audio logo but some do If you encounter any difficulty playing such discs please contact the disc manufacturer and demand a genuine CD in exchange Vivaldi Transport Manual v1_0x docx English version dCS Vivaldi Transport User Manual Software Issue 1 0x August 2012 STEP BY STEP GUIDE This section guides you through setting up the unit for basic operation Preliminaries The Menu Setup Guide sheet details the menu structure and describes the two most common set Ups For digital interfaces use with cables designed for digital audio e for AES EBU interfaces use 1100 screened twisted pair cables fitted with one male XLR connector and one female XLR connector e for SDIF Word Clock or SPDIF BNC interfaces use 750 coax cables fitted with BNC plugs SDIF and Word Clock interfaces require a simple DC coupled connection The interfaces may malfunction or not work at all if capacitor coupled cables or cables with built in networks are used e for SPDIF RCA interfaces use 750 coax cables fitted with RCA Phono plugs Connect the power cable supplied to the power inlet on the Transport rear panel plug the other end into a convenient power outlet Please do not u
3. it will close automatically Press again to return to normal operation To switch off hold down the Power button for about 5 seconds until SWITCHING OFF appears on the display then release it If the tray is open it will close automatically When the menu is open press the Power button to close the menu Menu Button Press the Menu button D to open the menu select menu pages and change settings See the Menu section on page 18 for information on using the menu features Layer Button After loading a hybrid CD SACD disc press the Layer button E if you want to select the CD layer The Transport will read the CD layer of the disc and then stop The Layer button has no effect when a single layer disc is loaded of if a hybrid disc is playing Vivaldi Transport Manual v1_0x docx English version dCS Vivaldi Transport User Manual Software Issue 1 0x August 2012 Play Pause Button After a disc has been read press the Play Pause button F to start playing Press again to pause and again to resume playing Rwd Button When a disc is playing press the Rwd rewind button G briefly to select the previous track or press and hold to jog back through the disc The rewind speed increases to x2 x4 and x8 as you hold the button down Release the button to return to play mode When the menu is open the Rwd button changes to the button used to page backwards through the menu Fwd Button When a disc is playing press the Fwd fo
4. product is serviced or repaired other than by dCS or our authorised service agents the product is operated without a mains earth or ground connection the unit is returned inadequately packed dCS reserve the right to apply a service charge if a product returned for warranty repair is found to be operating correctly or if a product is returned without a returns number being issued This warranty covers parts and labour only it does not cover shipping charges or tax duty Our dealers or distributors are NOT authorised to extend the terms of this warranty dCS cannot accept responsibility for any attempt to do so Products re sold by dCS on a used basis may be subject to reduced warranty terms Obtaining Service Should you encounter a problem contact your authorised dCS dealer for advice quoting the model the full serial number software version number and giving a detailed description of the fault Your dealer will advise you fully on actions that need to be taken When returning a unit the original packaging should be used to avoid transit damage Replacement packaging sets may be purchased from dCs During the Warranty period there will normally be no charge for parts or labour Operating Conditions e The supply voltage must remain within 10 of the A C voltage specified on the back panel e The supply frequency must be in the range 49Hz to 62Hz e Ambient temperature range 0 C 82 F to 40 C 104 F non con
5. range is 300ppm 444mm 17 5 long x 485mm 17 2 deep x 196mm 7 8 high Allow extra depth for cable connectors Allow space for air flow around the unit 23 2kg 51 1Ibs Internally set to either 100 115 120 220 or 230 240V AC 49 62Hz Power consumption 28W typical 40W maximum Consumes less than 0 5W when powered down from the front panel These specifications are subject to change without notice Vivaldi Transport Manual v1_0x docx English version dCS Vivaldi Transport User Manual Software Issue 1 0x August 2012 MAINTENANCE AND SUPPORT Service and Maintenance dCS audio products are designed not to need regular maintenance and contain no user serviceable parts apart from the mains fuse If your unit is damaged in any way please contact your dealer Replacing a Blown Mains Fuse There is a mains fuse below the power inlet accessible from the outside of the unit If the fuse blows it may be changed by the user The current consumption of the unit is very low so it only blows if power surges occur or there is a fault in the unit Usually power surges cause no other damage but if the fuse blows repeatedly on replacement some other damage will have been done and the unit must be returned to dCS for repair Fuse type 20mm x 5mm T 0 5 amp L fuse If the fuse should fail it is essential that it is replaced with one of the same type and rating Failure to do so
6. version dCS Vivaldi Transport User Manual Software Issue 1 0x August 2012 INFORMATION Menu The Unit Status page displays e Thelongversion of the serial number including the hardware configuration code e Internal temperature C e The clock frequency detected on the Word Clock Input Hz Use the lt gt buttons to scroll up or down the list This page does not time out press the Menu button to exit If your system is not behaving as you expect the Unit Status page can help you find set up or connection errors The Version page displays the software versions loaded in the unit and the full serial number Please have this information ready if you contact your dealer for any reason This page does not time out press the Menu button to exit The Contact page displays the 4CS web site URL and support email address This page does not time out press the Menu button to exit If you have any difficulty please contact your dealer for help first The Update feature allows you to load new software into your Transport Please follow the instructions supplied with the update disc carefully If you accidentally start an Update do not worry The unit will automatically detect it is not receiving updated software and will abort the process The software will not have been changed Vivaldi Transport Manual v1_0x docx English version dCS Vivaldi Transport User Manual Software Issue 1 0x August 2012 TRANSPORT SETTI
7. 9 STEP 2 Choosing a Sync Mode 10 Using the DAC in Master Mode 10 Using a Master Clock 11 STEP 3 Playing a Disc 12 Further suggestions 12 FIOnl Panelasic i nt 13 Remote Control Receiver 13 Display 13 Power Button 14 Menu Button 14 Layer Button 14 Play Pause Button 15 Rwd Button 15 Fwd Button 15 Stop Eject Button 15 CD Tray 15 Rear Pane iraa E E E E 16 AES Digital Outputs 16 SPDIF Digital Outputs 16 SDIF Digital Interface 16 Word Clock Input Output 16 Test interface 17 Mains inlet 17 Label 17 TAS MEO ii pala arena nn 18 Using the Menu 19 INFORMATION Menu 20 TRANSPORT SETTINGS Menu 21 DISPLAY SETTINGS Menu 22 GENERATOR Menu 22 SpPecliicatioi tsla idioti 23 Maintenance and Support sasssnsnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnna nnana 24 Service and Maintenance 24 Replacing a Blown Mains Fuse 24 Cleaning the case 24 Limited Warranty 25 If you need more help 26 Software History 26 Vivaldi Transport Manual v1_0x docx English version dCS Vivaldi Transport User Manual Software Issue 1 0x August 2012 USING THE dCS Vivaldi Transport FOR THE FIRST TIME Congratulations on purchasing your dCS Vivaldi Transport Before using your unit please read this section and the Step by Step Guide This will enable you to set the unit up quickly and safely with your hi fi system From time to time dCS will release updated software on CD that you can insta
8. DAC will lock to the source displaying the Audio Sync icon and DSD RAEN dd _ Transport DIGITAL OUT e r y A N d r S v Fi i 4 a ai v J e o r x d N v 7 J A lt j se si CRETA F amp S N VOLTAGE ni 6 7 SA LN Va N M j a f f f f 4 oe g d s j Pi i Analogue outputs To amplifier Figure 1 Basic setup Vivaldi Transport Manual v1_0x docx English version dCS Vivaldi Transport User Manual Software Issue 1 0x August 2012 Connecting the AES3 or an SPDIF output e Connect one of the outputs on the Transport to the matching input on the DAC using a suitable cable e Press the DAC Input button repeatedly until your chosen input is displayed This will be either AES1 AES2 AES3 SPDIF1 SPDIF2 or SPDIF3 BNC The DAC will lock to the source displaying the Audio Sync icon and 0 44 1 Connecting the SDIF interface e Connect the CH1 output on the Transport to the CH1 input on the DAC and the CH2 output to the CH2 input using two BNC cables Connect the Transport s Word Clock Out to the Word Clock In1 connector on the DAC Ensure the cables are not swapped e Press the DAC Input button repeatedly until SDIF appears on the display The DAC will lock to the source displaying the Audio Sync icon and 0 44 1 Why does the DAC display 0 44 1 Is the Transport faulty gt N
9. FF is displayed then release Further suggestions e If you wish you can set the AES1 2 output to generate DXD data 24 352 8 when playing a CD instead of DSD by changing the Settings gt Upsampling Mode menu page see page 21 e If you are using the AES1 2 output only try setting the PCM Enable menu page to Off see page 21 e lf you are using a Vivaldi Master Clock try turning the Dither feature on Try changing the Clock frequency to 88 2kHz or 176 4kHz Please refer to the Vivaldi Master Clock manual for more information e lf you have a Vivaldi Upsampler try driving it with CD data from the Transports PCM output and setting the Upsampler s Output to DSD or 352 8 DXD Please refer to the Vivaldi Upsampler manual for more information e If you have a complete 4 box Vivaldi system please see the Upsampler or DAC manuals for set up information Vivaldi Transport Manual v1_0x docx English version dCS Vivaldi Transport User Manual Software Issue 1 0x August 2012 FRONT PANEL Figure 4 Front panel Remote Control Receiver Aim the remote control handset towards the receiver A for best sensitivity Display In normal use the display B is split into 4 areas Area 1 The symbol indicates the mechanism status L gt Stop Eject Play Pause Fast Forward x2 Fast Reverse x2 Fast Forward x4 Fast Reverse x4 Fast Forward x8 Fast Reverse x8 Vivaldi Transport Manual v1_0x docx English ve
10. NGS Menu When a hybrid disc is loaded but is not playing the Layer page allows you to select either the SACD layer Wait is displayed The PCM Enable page turns the 16 44 1 PCM outputs AES3 SPDIF1 SPDIF2 amp SDIF On and off This gives a quieter electrical environment when you are using the AES1 2 interface only CD 0r CD layer While changing layers and re reading the disc Changing Layer Please i ar Y Remember to turn the PCM outputs on again if you want to use them DSD When playing a CD the Upsampling Mode page sets the format of the AES1 2 Dual AES interface to either encrypted DSD 1 bit at 2 822MS s DXD 0r DXD 24 bits at 352 8kS s gt There is no need for an Upsampling Off setting If you want to listen to the 16 44 1 data unprocessed connect one of the PCM format outputs AES3 SPDIF1 etc directly to the DAC and select that input T RS232 Mode sets the RS232 interface to either Text mode for use with 3 party control systems or gt B 4CS production Binary mode which is intended for factory use only Factory Reset resets the unit to standard settings These are Layer to SACD PCM Enable to On Upsample Mode to DSD Brightness to maximum Display to On RS232 Mode to Binary Vivaldi Transport Manual v1_0x docx English version dCS Vivaldi Transport User Manual Software Issue 1 0x August 2012 DISPLAY SETTINGS Menu Set the display Brig
11. S Vivaldi Transport User Manual software Issue 1 0x August 2012 Using a Master Clock The performance can be improved further by adding a Vivaldi Master Clock to the system le sa Transport Le PN DIGITAL OUT Analogue outputs To amplifier Figure 3 Using the Vivaldi Transport DAC and Clock together e Use the DAC s Input button to select the input you want to use AES1 2 in the example e Connect one of the Clocks Group 1 Word Clock Outputs to the Transport s Word Clock Input and the DAC s Word Clock Input 1 e Use the Clocks Freq1 button to set the Group 1 outputs to 44 1kHz W The Transport will lock to the Word Clock and display this icon vi Set the DAC s Settings gt Sync Mode menu page to Word Clock Ini and allow the Mi system to re lock Proceed to Step 3 Vivaldi Transport Manual v1_0x docx English version dCS Vivaldi Transport User Manual Software Issue 1 0x August 2012 STEP 3 Playing a Disc e Press the Stop Eject button The display will show OPEN e Load a CD or SACD into the tray with the label upwards and either push the tray in gently or press the Stop Eject button again The display will show CLOSE then LOADING The disc type will be identified either CD or the SACD logo will appear on the display along with the number of tracks and the total playing time The Transport will play the SACD layer of a hybrid disc by default but if you wish you can s
12. could result in damage to the unit risk of fire or electric shock and will invalidate the warranty Fuse failure is rare Referring to the diagram below remove the power cable insert small flat bladed screwdrivers into each fuse holder slot A push them together to release the clips and pull the fuse holder out Pull out the blown fuse and fit a new fuse in the holder B Orient the fuse holder as shown C and push the holder back into the unit so that it clicks home Spare fuses are provided with the unit A B C Cleaning the case The front and back panels of your dCS equipment are machined from very high grade aluminium Great care has been taken to create the finish of the aluminium throughout the engineering process from the raw solid material to the finished piece To remove loose dust or finger marks from the case we recommend that you use a clean dry lint free cloth To restore the finish we recommend applying small quantities of a lanolin based cleaner using a clean dry lint free cloth and then wiping off Do not allow lanolin to collect around the buttons Small amounts of glass cleaner containing ammonia may be used to clean other surfaces but avoid spraying onto the connector contacts Vivaldi Transport Manual v1_0x docx English version dCS Vivaldi Transport User Manual Software Issue 1 0x August 2012 Limited Warranty General dCS warrants this product against defect
13. dCS Vivaldi Transport Upsampling CD SACD Transport User Manual Software Release 1 0x August 2012 Data Conversion Systems Ltd 2012 Price UK 8 00 Euro 12 00 All rights reserved No part of this publication may be reproduced stored in or introduced into a retrieval system or transmitted in any form or by any means electronic mechanical photocopying recording or otherwise without the prior written permission of dCS Any person who does any unauthorised act in relation to this publication may be liable to criminal prosecution and civil claims for damages Information contained in this manual is subject to change without notice and whilst it is checked for accuracy no liabilities can be accepted for errors dCS is Data Conversion Systems Ltd Company registered in England No 2072115 dCS Vivaldi Transport User Manual Software Issue 1 0x August 2012 Vivaldi Transport Manual v1_0x docx Page 2 English version dCS Vivaldi Transport User Manual Software Issue 1 0x August 2012 Contents Using the dCS Vivaldi Transport for the first tiMe iii 4 What s in the box 4 Positioning the unit 4 Condensation 5 Safety Notice 5 Laser Radiation 5 Which types of disc can be played 6 Which types of disc can NOT be played 6 Step DV SIeb GU dea 7 Preliminaries 7 STEP 1 Connecting a Digital Output 8 Connecting the Dual AES interface 8 Connecting the AES3 or an SPDIF output 9 Connecting the SDIF interface
14. densing e Do not install the unit near heat sources such as radiators air ducts power amplifiers or direct strong sunlight e fin doubt the easy test is the unit is happy to work anywhere a human is Vivaldi Transport Manual v1_0x docx English version dCS Vivaldi Transport User Manual Software Issue 1 0x August 2012 If you need more help In the first instance you should contact your dealer If they cannot resolve the issue contact your national distributor Manufactured by Data Conversion Systems Ltd Unit 1 Buckingway Business Park Anderson Road Swavesey Cambridgeshire CB24 4AE UK www decesltd co uk This user manual may be downloaded free of charge from our web site A bound copy of this manual may be ordered from dCs Software History dCS products make extensive use of software configurable chips FPGAs and DSPs This gives us the ability to update our products to add extra features update digital interface standards or make performance improvements by loading new software Occasionally a hardware upgrade may be necessary also to increase the capacity of the electronics add extra connectors or extra front panel controls Please note that not all software updates produce an audible improvement We recommend that you keep your software up to date Check the 4CS web site occasionally for news of the latest software Updates please open the Info gt Version menu page and check the Contr
15. elect the CD layer instead by pressing the Layer button e Press the Play button Turn up the Volume to a comfortable level You should have audio For all discs the disc type and elapsed time will be displayed e Press the Play Pause button to pause playing press again to resume playing e Press the Fwd or Rwd button to skip to the next track or the previous track e Hold down the Fwd or Rwd button to jog through the track the speed will increase the longer you hold the button down Most owners will use the remote control for this e Press the Stop Eject button to stop the disc Press it again to open the tray The Remote Control gives access to other features such as track number selection display time selection repeat track or disc and programming a track sequence To program the track sequence 6 8 stop the disc and press the remote Program bution the Transport will display PGM Mode then OPGMO As an example press 6 or 06 the display will change to 6PGM1 Press 8 or 08 the display will change to 8PGM2 The remote Clear button cancels the last track entry Start the disc to play the track sequence To cancel Program Mode press the remote Program button or open the CD tray The next step is crucial sit back and enjoy the music When you have finished listening you can either keep the system warm by setting it to Sleep mode press the Power button briefly or switch off hold down the Power button until SWITCHING O
16. htness to a comfortable level using the lt or gt buttons Press the Menu button to exit Display On Off this page is usually set to On When set to Off and the menu closes the display will turn off after the menu closes The display will turn on briefly when a control setting is changed The display will stay on if the CD tray is empty or the menu is open GENERATOR Menu Channel Check runs a routine to test the system for swapped channels A tone is output on the left channel only while the display shows Left then the right channel only while the display shows Right If these are the wrong way around the left and right channels are swapped somewhere in your system FS Phase Check runs a routine to test the system for phase reversals Noise is output in dI phase on both channels while the display shows In Phase Press the Menu button the noise on the right channel is inverted while the display shows Out of Phase The first burst should produce a central image the second burst should not If these are the wrong way around one channel in your system is phase inverted Press the lt or gt button to stop the test and return to the menu Burn In runs a procedure to condition your system The unit displays Burn In Caution Loud then outputs modulated pink noise that ramps up slowly in level Press the Menu or lt or gt buttons to stop the procedure Please ensure that the volume level is reasonable as careles
17. ll yourself using the Update feature Please check our web site occasionally to see if new Vivaldi software is available or consult your dealer What s in the box Check that the box contains the following items e dCS Vivaldi Transport e Manual and Menu Guide e Power cable e AES cable e BNC cable e 2 spare fuses Notify your dealer as soon as possible if anything is missing or damaged We suggest that you retain the original packaging for possible future use If this is not possible replacement packaging can be ordered from dCS or our distributors Details can be found on our web site at www dcsltd co uk A dCS Premium remote control is supplied with the Vivaldi DAC The Premium remote control and a programmable Nevo Q50 colour touch screen remote control configured for Vivaldi are available as optional extras Positioning the unit For best sound quality the units in the Vivaldi range are designed to be mounted on separate shelves of a rack although they may be stacked directly on top of each other if this is absolutely necessary Place each unit on a firm vibration free base allowing convenient connection to the other parts of your system To prevent overheating we recommend that you leave some free space around the unit to allow for ventilation The unit is supplied with 4 feet fitted If you prefer a 3 feet layout unscrew the two back feet remove the two black cores using a 2 5mm A F Allen key fit one of the cores in
18. n be played compact Commercially manufactured CDs can be played if they e are 12cm or 8cm round discs e are recorded with linear PCM digital audio data e carry the Compact Disc Digital Audio logo and meet the Red Book standard DIGITAL AUDIO OA Commercially manufactured single layer SACDs or hybrid SACD CD discs can be OCT played if they SUPER AUDIO CD are 12cm or 8cm round discs e are recorded with DSD digital audio data on the SACD layer e carry the Super Audio CD logo and meet the Scarlet Book standard CD R CD R or CD RW discs recorded with audio data in CD format may be playable but this depends on the disc the software and the burner used to record on the disc CD RW dCS cannot accept responsibility for any difficulty encountered while attempting to play such discs Which types of disc can NOT be played dCS cannot accept responsibility for any difficulty encountered while attempting to play the following types of disc e Scratched damaged or dirty discs e Non circular discs such as square or heart shaped e Printed or labelled CD Rs or discs contaminated with glue or other sticky substances Contaminated discs may get stuck to the turntable inside the unit If this happens a service charge will be made for removing the disc and repairing any damage e DVD CD G CD EXTRA PHOTO CD CD ROM or DVD ROM e Discs recorded with digital audio data that is not in CD format e g FLAC or WAV files
19. o the Transport is working correctly When a CD is loaded but is not playing a 44 1kS s carrier signal is being transmitted but there is no data just digital silence The DAC correctly reports zero active data bits until the disc starts playing then it detects 16 active bits and updates the display 0 44 1 may be displayed briefly between tracks also Proceed to Step 2 Vivaldi Transport Manual v1_0x docx English version dCS Vivaldi Transport User Manual Software Issue 1 0x August 2012 STEP 2 Choosing a Sync Mode So far the system has been set up to lock to the clock generated by the source This is the simplest arrangement but it does not give the best sonic performance due to clock jitter Using the DAC in Master Mode If you have a Vivaldi Clock go to the next page You can reduce the jitter in your system by using the Vivaldi DAC in Master mode and slaving the Transport to it Rsa wie Transport Analogue outputs To amplifier Figure 2 Using the Vivaldi Transport with the DAC in Master Mode e Use the DAC s Input button to select the input you want to use AES1 2 in the example e Connect the DAC s Word Clock Out connector to the Transport s Word Clock In connector Set the DAC s Settings gt Sync Mode menu page to Master mode W The Transport will lock to the Word Clock and display this icon Vivaldi Transport Manual v1_0x docx English version dC
20. ol Board version to verify l S Update discs are available from our distributors Before requesting an update disc Y that an update is actually needed This manual is for Vivaldi Transport software version 1 0x Issue 1 00 The first issue Vivaldi Transport Manual v1_0x docx English version
21. own on the serial number label If this does not match your local supply voltage DO NOT attempt to use the unit Contact your dealer to have the unit reset Using the unit with the wrong mains setting for your local supply may result in serious damage to the unit and will invalidate the warranty Do not attempt to reset the voltage yourself We do not recommend the use of mains regenerators However if you do wish to use a mains regenerator with variable voltage and frequency we recommend that you set the voltage to match your local voltage and the frequency to either 50Hz or 60Hz ONLY Damage caused to your Vivaldi Transport by misuse of a mains regenerator or by a malfunctioning mains regenerator is not covered by the warranty Disposal at end of life the symbol indicates that this product should not be treated as normal household waste It should be recycled so please take it to an approved collection facility Laser Radiation dCS Vivaldi Transport is a Class 1 Laser Product it complies with U S FDA 21CFR subchapter J In normal use there is no risk of exposure to laser radiation The case should only be opened by authorised service personnel The case protects the user from indirect exposure to visible and invisible laser radiation as well as risk of electric shock Vivaldi Transport Manual v1_0x docx English version dCS Vivaldi Transport User Manual Software Issue 1 0x August 2012 Which types of disc ca
22. rsion dCS Vivaldi Transport User Manual Software Issue 1 0x August 2012 Area 2 When in play or pause modes the current track number amp track disc time hours minutes seconds is shown When stopped the number of tracks amp total disc time is shown PGM is displayed here when a track sequence is programmed and the disc is stopped For example 8PGM3 indicates that a sequence of 3 tracks has been programmed and the last one is track 8 Area 3 The icon defines the time that is displayed set by the remote Display button Track time elapsed Track time remaining Area 4 The status icons are displayed here SACD loaded W Locked to Word Clock input x Wrong clock detected Repeat the current track Repeat the whole disc Details of the menu displays are shown in the Menu section on page 18 Disc time elapsed Disc time remaining CD loaded D D lt To avoid unnecessary display wear we recommend switching off or setting the unit to Sleep mode at the end of the listening session Power Button To switch on ensure the rear panel switch is set to and press the Power button C on the front panel once Note that the unit cannot be turned on from the remote control To set the unit to sleep mode press the Power button once The main display will turn off the LED over the button will illuminate and the mechanism will stop but the unit will remain close to running temperature If the tray is open
23. rward button H briefly to select the next track or press and hold to jog forward through the disc The fast forward speed increases to x2 x4 and x8 as you hold the button down Release the button to return to play mode When the menu is open the Fwd button changes to the gt button used to page forwards through the menu Stop Eject Button Press the Stop Eject button I to stop playing a disc Press again to open the CD tray Press again to close the CD tray CD Tray When loading a CD or SACD into the CD tray J ensure the disc is central with the label upwards and is seated correctly The tray will close automatically if it is left open for more than a few minutes Vivaldi Transport Manual v1_0x docx English version dCS Vivaldi Transport User Manual Software Issue 1 0x August 2012 REAR PANEL S N a VOLTAGE ia Figure 5 Rear panel AES Digital Outputs The AES1 and AES2 outputs K form a Dual AES pair They output encrypted DSD data when an SACD is playing When playing a CD the outputs can be set to output either encrypted DSD or DXD 24 bits at 352 8kS s depending on the setting of the Settings gt Upsample Mode menu page AES1 2 is the main output The AES1 2 interface is intended to work with the Vivaldi DAC only it is unlikely to be compatible with other manufacturer s products At present this interface is not compatible with other dCS DACs AES3 L outputs 16 44 1 AES EBU format da
24. s in materials and workmanship for a period of 3 years from the date the unit was originally shipped from dCs If the product is purchased and registered with dCS within 6 months of the date the unit was originally shipped from dCS we will start the warranty on the purchase date For units registered later than 6 months from the ship date we will start the warranty from the ship date unless the registration is supported by the original sales invoice During the warranty period 4CS will repair or at our absolute discretion replace a faulty product Warranty repairs must only be carried out by dCS or our authorised service agents Please contact your dealer if your unit requires service To register this product either register online at www dcsltd co uk page warranty or complete the Product Registration form within 30 days of the sale and return it to dCS On receipt of the registration dCS will add your contact details to our customer database dCS will use this information for warranty purposes only we will not contact you directly for reasons relating to sales and marketing This warranty applies to the original owner it is not transferable Warranty Exclusions The Warranty does not cover wear and tear The Warranty on this product will be void if the product is misused in any way any unauthorised modifications or repairs are carried out the product is not used in accordance with the Operating Conditions stated in this manual the
25. s use of the Burn In feature can damage your amplifiers and loudspeakers dCS will not be liable for such damage Vivaldi Transport Manual v1_0x docx English version dCS Vivaldi Transport User Manual Software Issue 1 0x SPECIFICATION Mechanism type Digital outputs Clocking Size and weight Power requirements August 2012 TEAC Esoteric VRDS NEO VMK8 dual laser CD SACD mechanism Dual AES interface on 2x 3 pin male XLR connectors AES1 2 While an SACD is playing the interface outputs encrypted DSD data While a CD is playing the Settings gt Upsample Mode menu page sets the interface to output either encrypted DSD data 1 bit at 2 822MS s or DXD data 24 bits at 352 8kS s AES EBU on 3 pin male XLR connector AES3 Outputs 16 44 1 data whether a CD or SACD is playing 2x SPDIF on 1x RCA Phono and 1x BNC connectors Each outputs 16 44 1 data whether a CD or SACD is playing 1x SDIF 2 interface on 2x BNC connectors outputs 16 44 1 data whether a CD or SACD is playing Word Clock Output on 1x BNC connector With the transport in Master mode a TTL compatible 44 1kHz word clock derived from the internal crystal oscillator is available on this output The calibration accuracy when shipped is 10ppm not temperature compensated Calibration usually remains stable for several years Word Clock Input on 1x BNC connector accepts standard word clock at 44 1 88 2 or 176 4kHz Sensitive to TTL levels Lock
26. se an excessively heavy or inflexible power cable as this may damage the power inlet connector The cables supplied with the unit are commercial grade because most owners will have their own audiophile grade cables or will prefer to make their own cable choices Set the rocker switch near the mains inlet to the position Press the Power button the unit will display Vivaldi Transport Wait about 30 seconds while the Transport configures itself If the unit is likely to be set in an unfamiliar state you can run the Factory Reset routine by pressing the buttons in this sequence Menu gt Menu lt lt Menu Wait a few seconds while the unit resets itself Vivaldi Transport Manual v1_0x docx English version dCS Vivaldi Transport User Manual Software Issue 1 0x August 2012 STEP 1 Connecting a Digital Output Whether you are playing a CD or an SACD the AES1 2 interface carries DSD data and all of the PCM outputs carry 16 44 1 PCM data Most owners connect the AES1 2 interface only but some prefer to listen to CDs in the native 16 bit 44 1kS s format Connecting the Dual AES interface When used with a Vivaldi DAC AES1 2 is the main output e Connect the AES1 output on the Transport to the AES1 input on the Vivaldi DAC rear panel and the AES2 output to the AES2 input using two XLR cables Ensure the cables are not swapped e Press the DAC s Input button repeatedly until AES1 2 is displayed The
27. ser Manual Software Issue 1 0x August 2012 Using the Menu The menu gives the user access to a range of additional features It also allows new features and performance enhancements to be added later by software updates The menu is controlled by four buttons Press the Menu button to open the menu or select a setting Press the button to page forward through the menu Press the lt button pages backward through the menu Press the Power button to close the menu or just wait 10 seconds Use the Menu Guide sheet to help you find the right menu page Each unit in the range has either three or four top level menu pages Each model has a different SETTINGS menu which allows you to set some features that are not directly accessible from the front panel contact details The DISPLAY SETTINGS menu is used to adjust the display i The INFORMATION menu gives unit set up details software issues serial number and The SIGNAL GENERATOR menu featured on the Transport Upsampler and DAC only contains test and set up routines Use the gt button to move the blue highlight to the menu you want then press the Menu button to select it The next menu level down is displayed Use the button to move the highlight to the menu page you want then press the Menu button to display the information or change the setting Select the return icon to go back to the previous menu level Vivaldi Transport Manual v1_0x docx English
28. ta whether a CD or SACD is playing SPDIF Digital Outputs The unit features two co ax SPDIF outputs labelled SPDIF1 M RCA connector and SPDIF2 N BNC connector Both output 16 44 1 format data whether a CD or SACD is playing SDIF Digital Interface The SDIF interface outputs 16 44 1 format data whether a CD or SACD is playing The interface consists of two data inputs labelled CH1 and CH2 O on 2x BNC connectors supported by the Word Clock Output Q Word Clock Input Output The Word Clock In connector P will accept standard word clock at 44 1 or 88 2 or 176 4kHz from a master clock or a DAC in master mode W Once the unit has locked to the clock this icon appears on the display The Word Clock Out connector Q carries a 44 1kHz word clock Word clock is used for synchronisation only it does not carry digital data Vivaldi Transport Manual v1_0x docx English version dCS Vivaldi Transport User Manual Software Issue 1 0x August 2012 Test interface This RS232 interface R has two modes set by the Settings gt RS232 menu page e Binary mode is used to remotely control the unit during automated production testing at dCs e ext mode is for use with a household automation system If you would like to use this mode please download the list of remote control commands from www dcsltd co uk page support The interface is designed to be used with a straight through cable wired pin 1 to pin 1 etc
29. the middle position and replace the foot Take care not to cross thread the foot With all feet screwed fully home the unit will sit level on a flat surface If you need to do any levelling you can unscrew any of the feet up to 3 complete turns to give up to 3mm 1 8 of height adjustment Vivaldi Transport Manual v1_0x docx English version dCS Vivaldi Transport User Manual Software Issue 1 0x August 2012 Condensation If the Transport is cold and is moved into a warm room condensation will form inside the unit This interferes with normal operation Remove the Transport from its packaging and let it stand for 1 2 hours to allow it to reach room temperature and the condensation to evaporate Safety Notice Your dCS Vivaldi Transport contains no user serviceable parts DO NOT attempt to open the case as there are potentially dangerous voltages present inside In the event of the unit developing a fault please contact your dealer in the first instance To maintain protection from electric shock the unit MUST be connected to mains earth ground via the power cable Also unearthed systems do not give the best sonic performance Vv This product is lead free and complies with the RoHS directive RoH lead free 2002 95 EC Before connecting the power cable to the unit for the first time please check that it has been set to the correct operating voltage for your mains supply The unit s voltage setting is sh
Download Pdf Manuals
Related Search