KV-901T & AV-901R Quick Guide
Contents
1. that are currently on the network just press the source button to move the highlight to the desired Transmitter wait a few seconds and the settings will be saved and restart The prefixed indicate the Transmitter with that priority setting By Priority 1 KV 901T 08d8 192 168 168 201 2 KV 901T fffd 192 168 168 204 KV 901T 08d8 192 168 168 201 3 3 5 3 Dedicated Set the AV 901R to connect with a dedicated KV 901T Transmitter Dedicated TX KV 901T 08d8 192 168 168 201 3 4 The AV 901R Setting From the System menu push the AV 901R source button and navigate to the gt REFRESH push the button again during the system is still showing Searching KV 901T The menu with AV 901R SETTING will be shown as below gt KV 901T 0337 192 168 168 201 03 27 Push the source button again gt REFRESH to navigate to the gt AV 901R gt AV 901R SETTING gt AV 901R OFF SETTING it will show the following OSD menu gt AUDIO INPUT gt IR INPUT gt Connection Method gt RETURN 3 4 1 AUDIO INPUT To enable disable the microphone input function 3 4 2 IR INPUT There are 3 options for IR input IR DISABLE Turn off the IR function INTERNAL IR To set the IR receiver from internal socket EXTERNAL IR To set the IR receiver from extension cable 3 4 3 Connection Method Please refer to 3 3 52. KV 901T amp AV 901R Quick Guide This quick guide provides basic information only for a complete version of user s manual please down load at http www avextender com comm upfile p 110913 04468 pdf Copyright 2011 Beacon Extender Inc All rights reserved Version 4 01 1 Introduction The KV 901T AV 901R is a solution of Audio Video extension over IP Ethernet LAN The KV 901T is Transmitter TX the AV 901R is Receiver RX The TX connects with PC or any source with VGA DVI Audio output The RX connects with display and speaker Any 100M Giga or Fiber Ethernet LAN switch can be used to inter connect the TX and RX They are flexible in one to one Unicast mode or in one to many many to many Multicast mode 1 1 Specification Input video amp resolution Input video can be VGA or DVI D in all standard resolutions from 640 x 480 to 1920 x 1200 60Hz 70Hz and the following special resolutions 1440 x 900 1400 x 1050 1680 x 1050 1360 x 768 Output video amp resolution Output video can be VGA or DVI F in all standard resolutions from 640 x 480 to 1920 x 1080 60Hz 70Hz and the following special resolutions 1440 x 900 1400 x 1050 1680 x 1050 1360 x 768 Output frame rate 640X480 70fps 800X600 70fps 1024X768 60fps 1280X1024 30fps 1600X1200 30fps 720X480 60fps 720X576 50fps 1280X720 30fps 1440x900 30fps 1400x1050 30fps 1680x1050 30fps 1360x768 30fps 1920X1080 25fps Scalar support Allows differenc
3. e input and output resolution also support input VGA output DVI D input DVI D output VGA LAN 10 100Mbps Auto MDIX Flow control IR Bridge IR in out 38 KHz optional Remote PC Control PS2 or USB optional Audio Microphone 48 KHz stereo audio and microphone RS232 Bridge AV 901R support remote RS232 baud 2400 115200 optional 2 Installation Setup 2 1 Install KV 901T Transmitter 1 The DVI input of the KV 901T is DVI I VGA DVI D You can use the accessory of VGA to DVI cable to connect KV 901T to PC VGA Out Or you can prepare a DVI to DVI cable to connect KV 901T to PC DVI Out There is a VGA Out on the KV 901T for the VGA loop out It is only available when the input video is DVI A or VGA You can attach a VGA monitor on this VGA Out for local display Use accessory of audio cable to connect KV 901T Line IN to the PC Line Out Use optional accessory of Mini USB to A cable to connect KV 901T Mini USB to PC USB for keyboard mouse remote control Use optional accessory of IR blaster cable to connect KV 901T IR Out and adjust the IR blaster LED face to the IR receiver of your Media Center PC TV tuner card or DVD player Use CAT5e 6 7 cable to connect KV 901T Ethernet to the Ethernet switch or directly to the AV 901R All of KV 901T and AV 901R must be put in the same network and should not be inter connected with router Use the included 12V DC power adapter to co
4. network and should not be inter connected with router 7 Connect the included DC 5V 2A power adapter to the DC IN and plug the power supply to wall To avoid damage to the AV 901R please use power adapter in the package 8 There is a Source button on the front panel for the system OSD operation menu Please refer to Chapter 3 for detail 9 There is a Power LED and 2 RJ45 LEDs on the AV 901R please refer to the below table for the status of AV 901R Power LED RJ45 Status Red Green Green Orange Off No Power On System OK network is not connected Blink On System failed On On System OK network is connected but not able to link with Transmitter On On System OK linked with Transmitter On on on System OK dis connected with Transmitter the Power LED in orange color On On On System OK network overload 10 The Reset button on the AV 901R Rear panel can be used for entering Advance Setup Mode please refer to Chapter 4 The AV 901R panel diagram is shown as below Select To PS2 KB amp Mouse Front Rear To RS232 To DVI VGA Line Mic To Lan Control monitor Out In 3 System Menu OSD 2 types of OSD On Screen Display menu in AV 901R Receiver Transmitter List menu and System menu You can enter Transmitter List menu by pressing lt Ctrl gt lt Ctrl gt hotkey Pressing the AV 901R Source button will bring you to the System menu To Power 3 1 Transmi
5. nnect KV 901T DC IN power socket and plug the power supply to wall There is a Status LED and 2 RJ45 LEDs on the KV 901T please refer to the below table for the status of KV 901T Status LED RJ45 LED Status Red Green Green Orange On System OK network is not connected Blink On System failed On On System OK network is connected On On On System OK network overload The Reset button on the KV 901T Rear panel can be used for entering Advance Setup trueio Chapter 4 The panel Rear diagram is shown as right 2 2 Install AV 901R Receiver 1 The DVI output of the AV 901R is DVI I VGA DVI D You can use the accessory of VGA to DVI cable to connect AV 901R to the VGA monitor Or you can prepare a DVI to DVI cable to connect AV 901R to the DVI monitor 2 Use accessory of audio cable to connect AV 901R Line Out to speaker and plug microphone into the Mic In port 3 If you need remote keyboard mouse function plug keyboard and mouse to the PS2 or optional USB port 4 If you need remote RS232 function plug RS232 cable to the RS232 port 5 If you need remote IR function connects optional IR receiver cable to the IR extender port and positioned the receiver to be visible from the front of the Display 6 Use CAT5e 6 7 cable to connect AV 901R Ethernet to the Ethernet switch or directly to the KV 901T All of KV 901T and AV 901R must be put in the same
6. tter List menu To active the Transmitter List menu press the lt Ctrl gt key twice within two seconds you may see the OSD menu showing a list of all KV 901T Transmitters as below Main Menu The menu shows 4 x KV 901T are 1 P found in the network with name of KV 9001 PC1 KV 9001 PC4 Navigate to the desired Transmitter with the arrow keys and press lt Enter gt The selected KV 901T appears on the display and you can use keyboard mouse to control the selected PC Press F1 to refresh Transmitters list Press F10 to change hotkey option lt CTRL gt lt SHIFT gt or lt ALT gt Name of Kv 901T Function Setting 3 2 System menu When the AV 901R Receiver is turned on it will search all KV 901T available on the network and show on the System menu gt VGA SYNC gt REFRESH gt KV 901T SETTING gt AV 901R OFF gt Connection Method gt EXIT Press the Source button to select KV 901T after 3 seconds the AV 901R will connect to that KV 901T as below Connecting to After the connection is established the AV 901R will display the screen that is connected to that KV 901T 3 3 Other System menu Functions When the source button of AV 901R is pressed the system menu OSD will pop out You can press the source button to navigate other System menu functions 3 3 1 VGA SYNC This function is only available when the KV 901T is connected with VGA input when the picture shifts from screen
7. use this function to auto adjust the picture 3 3 2 REFRESH To refresh the KV 901T Transmitters list 3 3 3 KV 901T SETTING Use this function to setup KV 901T gt BANDWDITH SETTING gt INFORMATION gt EXIT 3 3 3 1 MULTI ONE AV 901R To set KV 901T in Multicast mode for one to many or Unicast mode for one to one 3 3 3 2 BANDWIDTH SETTING KV 901T has 3 levels of bandwidth LOW MID HIGH Please note to set LOW it will use lower network bandwidth and get a more efficient performance but will come with lower image quality 3 3 3 3 INFORMATION Show the KV 901T AV 901R basic information KV 901T VERSION aa26 SUPPORT MULTI AV 901R BANDWIDTH LOW DVI IN 1024 X 768 AV 901R VERSION a901 0126 IP 192 168 168 22 VGA OUT 1024 X 768 MIC IN INTERNAL IR 3 3 4 AV 901R OFF To disable the connection between the AV 901R and the currently connected KV 901T To enable the connection press the push button again AV 901R off 3 3 5 Connection Method The system provides 3 connection method gt First Available gt By Priority gt Dedicated gt EXIT 3 3 5 1 First Available This function sets the AV 901R to connect to the first available KV 901T which it found first 3 3 5 2 By Priority This function sets the AV 901R to connect to the KV 901T according to the priority You can set the 1 and 2 priority for 2 different KV 901T As the following picture there are two sections each has a list of all Transmitters
Download Pdf Manuals
Related Search