Corporate names revised in the documents
Contents
1. through the manual before using the product and follow the instructions contained therein to use it correctly In particular carefully read IM Caution of the products described in this manual at the beginning of this manual to understand the requirements for safe use of the product before using it After reading the manual keep it handy for future reference EM Related manuals You should refer to the following manuals as well e HARDWARE MANUAL for each type of microcontroller DATA SHEET for each type of microcontroller SOFTUNE Workbench OPERATION MANUAL SOFTUNE Workbench USER S MANUAL SOFTUNE Workbench COMMAND REFERENCE MANUAL E European RoHS compliance Products that have a E suffix at the end of the part number are products that conform to the Euro pean RoHS Consult a Fujitsu sales or support representative for details on the products that are RoHS compliant Products that have a E suffix on the part number have the same functionality as products with the same part number but without the E suffix RoHS non compliant products EM Caution of the products described in this document The following precautions apply to the product described in this manual N WARNING Indicates a potentially hazardous situation which if not avoided appropriately could result in death or serious injury and or a fault in the user s system Electric shock Damage Before perform2. User interface circuitry SIN User interface connector The pin names of the user interface connector show the pin names to connect to the evaluation Connector pin number Table 6 DC specifications of the user interface Circuit type Open drain output Resistor connection Connected to UVCC by 10kQ Remarks Connected to GND via bus switch CMOS input CMOS input output CMOS output The H level output current 2 The L level output current See Figure 8 3 The input leakage current 4 Does not include the current through the pull up resistance 5 The voltage monitoring IC controls the on off connection to the GND via bus switch S01 00024 1E FUJITSU SEMICONDUCTOR e SUPPORT SYSTEM F2MC Family BGM ADAPTER MB2146 09A E OPERATION MANUAL August 2007 the first edition Published FUJITSU LIMITED Electronic Devices Edited Business Promotion Dept co FUJITSU
3. directly to death personal injury severe physical damage or other loss i e nuclear reaction control in nuclear facility aircraft flight control air traffic control mass transport control medical life support system missile launch control in weapon system or 2 for use requiring extremely high reliability i e submersible repeater and artificial satellite Please note that FUJITSU will not be liable against you and or any third party for any claims or damages arising in connection with above mentioned uses of the products Any semiconductor devices have an inherent chance of failure You must protect against injury damage or loss from such failures by incorporating safety design measures into your facility and equipment such as redundancy fire pro tection and prevention of over current levels and other abnormal operating conditions If any products described in this document represent goods or technologies subject to certain restrictions on export un der the Foreign Exchange and Foreign Trade Law of Japan the prior authorization by Japanese government will be required for export of those products from Japan Copyright 2007 FUJITSU LIMITED All rights reserved 1 Checking the Delivered Product Before using the product make sure that the package contains the following items e BGM adapter e USB cable 2 0m 1 1 e Operation manual Japanese version 1 1 e Operation manual English version This document
4. or storage environment can cause a fault Use the product within the ranges of its general specifications Operating it outside the range of any general specification may cause a fault Damage To prevent electrostatic breakdown do not let your finger or an object touch any metal part of the connector Before handling the product touch a metal object such as a door knob to discharge static electricity from your body Damage Before turning the power on be sure to finish making all the required connections To set up and use the product follow the instructions given in this document Using the product incorrectly or inappropriately may cause a fault Damage Before plugging or unplugging any cable for this product be sure to turn the power supply off When unplugging the cable remove it while holding the connector with out pulling the cable itself Pulling the cable itself or bending it may expose or dis connect the cable core resulting in a fault Damage Re transporting the product may damage it to cause a fault Keep the packaging materials used for shipment of the product and use them when re transporting it e The contents of this document are subject to change without notice Customers are advised to consult with FUJITSU sales representatives before ordering e The information such as descriptions of function and application circuit examples in this document are presented sole ly for the pu
5. Referred to as the adapter 2 Optional Parts A variety of optional parts are available for this adapter that may be purchased separately as needed Consult a Fujitsu sales or support representative for details 3 Appearance and Part Names Figures 1 and 2 show the adapter appearance major dimensions and part names User interface connector POWER LED USB connector 100mm 100mm Figure 1 Adapter appearance top view USB connector 25mm 40mm Figure 2 Adapter appearance front view 4 System Configuration M Using the adapter as an emulator system Connect the adapter between the host computer and the user system so that the adapter can serve as an emulator under control of the host computer For using emulator debugger software on the host computer refer to the SOFTUNE Workbench OPERATION MANUAL Figure 3 shows the system configuration when the adapter is used as an emulator system 1 2 i User Adapter Host Adapter interface interface MCU computer connector connector User system USB cable Interface cable flat cable of the adapter Figure 3 System configuration emulator system EM Using the adapter as a USB programmer The adapter connects the host computer and the serial interface of MCU with built in flash memory made by Fujitsu and writes dat
6. a in a built in flash memory For information on the USB programmer contact the Fujitsu sales or support representative Figure 4 shows the system configuration when the adapter is used as a USB programmer 1 2 MCU with User Adapter built in flash Host i Boe interface interface memory p connector connector made by Fujitsu User system USB cable Interface cable flat cable of the adapter Figure 4 System configuration USB programmer 5 Connections E Connection to the host computer Connect the adapter to the host computer using the USB cable Figure 5 shows how to connect the USB cable 1 e R Connection to the USB connector of the adapter Adapter Figure 5 Connecting the USB cable EH Connection to the user system Connect the adapter to the user system Plug the user interface connector of the adapter into the adapter interface connector on the user sys tem When connecting the user interface connector align the index marks pin 1 on each of the connec tors For the specifications of the adapter interface connector see IB Adapter interface specifications in Section 6 Specifications Figure 6 shows how to connect the adapter to the user system Adapter interface connector on the user system User interface connector EELEE EEE Index mark pin 1 Adapter User syst
7. cO THE POSSIBILITIES ARE INFINITE FUJITSU Corporate names revised in the documents The Fujitsu Limited reorganized its LSI business into a wholly owned subsidiary the Fujitsu Microelectronics Limited on March 21 2008 The corporate names Fujitsu and Fujitsu Limited described all in this document have been revised to the Fujitsu Microelectronics Limited Thank you for your cooperation and understanding this notice Moreover there are no changes in the related documents other than corporate names revised Customers are advised to consult with sales representatives before ordering March 21 2008 Fujitsu Microelectronics Limited FUJITSU SEMICONDUCTOR SUPPORT SYSTEM SS01 00024 1E F2MC Family BGM ADAPTER MB2146 09A E OPERATION MANUAL co FUJITSU PREFACE Thank you for purchasing the F2MC family BGM adapter model number MB2146 09A E The product is a development support tool for developing and evaluating applied products which use Fujitsu microcontrollers hereafter MCUs that have a BDSU module This manual describes how to handle the F2MC family BGM adapter Be sure to read it before using the product For information on the MCUs supported by this product contact the Fujitsu sales or support repre sentative FMC is the abbreviation of FUJITSU Flexible Microcontroller EM For your safety This manual contains important information required for using the product safely Be sure to read
8. em Figure 6 Connecting to the user system 6 Specifications E General specifications Table 1 lists the general specifications of the adapter Table 1 General specifications Item Specification Name F MC family BGM adapter Model number MB2146 09A E Power supply Adapter power input Max 50mA uses USB BUS power specifications User power input 2 7V to 5 5V Max 20mA Green On when only adapter power is supplied with the USB cable connected Red On when only user power is supplied Orange On when both adapter power and user power are supplied POWER LED indication User interface connector MIL standard compliant key type with center key Operating temperature humidity 5 C to 35 C 20 to 80 no condensation Storage temperature humidity 0 C to 70 C 20 to 80 no condensation Adapter case 40mm W x 100mm D x 25mm H excluding protrusions Dimensions Interface cable length 100mm excluding user interface connector Weight 55g The maximum and minimum voltages depends on the MCU used For details contact the Fujitsu sales or support representative 2 Does not include the power consumption of the MCU 3 The part number of the connector is FAS 1001 2101 OBF YAMAICHI ELECTRONICS Co Ltd m USB line specifications Table 2 lists the USB line specifications of the adapter Table 2 USB line specifications It
9. em Description Conforming standard USB1 1 Communication method Full speed bulk transfer Data transfer rate 12Mbps Connector shape Series B Power supply BUS Powered EM Tool reset specifications A tool reset is a hardware reset by the adapter to reset the entire system of the MCU including the BDSU module on the user system When both of the adapter power and MCU s user power are turned on the tool reset is canceled au tomatically to enable the MCU to be evaluated The following shows how to generate a tool reset and how long it remains in effect e Tool reset generation methods and reset L pulse width 1 Turn the MCU user power from OFF to ON power on reset The reset remains in effect for about 16ms to 70ms after the MCU user power is supplied 2 Turn the adapter power from OFF to ON by unplugging and plugging the USB cable The reset remains in effect for about 32ms to 140ms after the adapter power is supplied If an uncontrollable malfunction occurs in the user system and adapter that cannot be recovered using tool reset generation method 1 execute tool reset generation method 2 m Adapter interface specifications The pinouts of the adapter interface connectors mounted on the user system are shown in Tables 3 and 4 The recommended connectors are listed in Table 5 and the pin configuration is shown in Fig ure 7 When the adapter interface connector is mounted on the us
10. er system connect the MCU to the adapter Connector pin number interface connector according to the following specifications Table 3 Adapter interface connector pinout emulator system Input output BGMA MCU Evaluation MCU connection pin name UVCC Function User power supply input Remarks Connected to the MCUs Vcc pin GND Vss pin Connected to the MCUs Vss pin TRESETX Tool reset output BDSU Initialization of users logic open collector output DMDX Mode change output 0 Debug mode 1 Free run mode SOUT Serial data input SD for UART EXC External clock input Base clock for UART SIN Serial data output RD for UART NC Not used and not connected Vss pin Connected to the MCUs Vss pin BGMA MCU BGMA represents the BGM adapter 2 MCU represents the evaluation MCU Connector pin number User power supply input Connected to the MCUs Vcc pin Table 4 Adapter interface connector pinout USB programmer Input output BGMA MCU Evaluation MCU connection pin name Function User power supply input Remarks Connected to the MCUs Vcc pin Vss pin Connected to the MCUs Vss pin BGMA gt MCU Tool reset output Mode change output BDSU Initialization of users logic open collector output Not used and not connected BGMA e MCU Seria
11. ing any operation described in this manual turn off all the power supplies to the system Performing such an operation with the power on may cause an electric shock or device fault Electric shock Damage Once the product has been turned on do not touch any metal part of it Doing so may cause an electric shock or device fault N CAUTION Indicates a potentially hazardous situation which if not avoided appropriately may result in minor or moderate injury and or damage to the product or the equipment to which the product is connected to software resources such as data or to other properties Cuts Damage Before moving the product be sure to turn off all the power supplies and unplug the cables Watch your steps when carrying the product Do not use the product at an unstable location such as a place exposed to strong vibration or a sloping surface Doing so may let the product fall resulting in an injury or fault Damage Neither put anything on or apply shock to the product Once the product has been powered do not carry it Doing either may cause a fault due to a load or shock Damage Damage Since the product contains many electronic components keep it away from direct sunlight high temperature and high humidity to prevent condensation Do not use or store the product where it is exposed to much dust or a strong magnetic or elec tric field for an extended period of time An adverse operating
12. l data input SD for UART BGMA MCU Synchronous clock output Base clock for UART BGMA MCU Serial data output RD for UART Not used and not connected Vss pin Connected to the MCUs Vss pin BGMA MCU User power supply input Connected to the MCUs Vcc pin BGMA represents the BGM adapter 2 MCU represents the evaluation MCU 3 Refer to the specifications of each of the MCUs for the serial port number that corresponds to the serial interface for the USB programmer Part number FAP 1001 2202 0BF Table 5 Recommended adapter interface connectors Right angle solder dip Specifications Housing provided Middle latch provided Manufacturer FAP 1001 2204 0BF Straight solder dip Housing provided Middle latch provided YAMAICHI ELECTRONICS FAP 10 0842 0BF Right angle solder dip Housing provided Latch not provided Co Ltd FAP 10 0844 0BF Straight solder dip Housing provided Latch not provided Index mark m Vv 9pin TOP VIEW Figure 7 Adapter interface connector pin configuration To internal adapter control CPU To supply voltage monitoring IC koa 3 3V 10kQS10kQ yw A MCU on the emulator system uvec 10kQ io 10k TRESETX TC7MBD3244AFK SOUT EXC F wv NNCDS5 6LH A Figure 8
13. rpose of reference to show examples of operations and uses of FUJITSU semiconductor device FUJITSU does not warrant proper operation of the device with respect to use based on such information When you develop equipment incorporating the device based on such information you must assume any responsibility arising out of such use of the information FUJITSU assumes no liability for any damages whatsoever arising out of the use of the infor mation e Any information in this document including descriptions of function and schematic diagrams shall not be construed as license of the use or exercise of any intellectual property right such as patent right or copyright or any other right of FUJITSU or any third party or does FUJITSU warrant non infringement of any third party s intellectual property right or other right by using such information FUJITSU assumes no liability for any infringement of the intellectual property rights or other rights of third parties which would result from the use of information contained herein e The products described in this document are designed developed and manufactured as contemplated for general use including without limitation ordinary industrial use general office use personal use and household use but are not designed developed and manufactured as contemplated 1 for use accompanying fatal risks or dangers that unless extremely high safety is secured could have a serious effect to the public and could lead
Download Pdf Manuals
Related Search