iPC-Series PCs
Contents
1. CSA C22 2 213 See appropriate note below for the applicable unit or option being utilized NOTE PANEL MOUNT VERSIONS SUITABLE FOR USE IN CLASS I DIVISION 2 GROUPS A B C AND D CLASS II DIVISION 2 GROUPS F AND G CLASS Ill HAZARDOUS LOCATIONS OR NONHAZARDOUS LOCATIONS ONLY FOR USE ON A FLAT SURFACE OF A TYPE 1 4 4X OR 12 ENCLOSURE WITH PROVISIONS FOR CLASS I DIVISION 2 WIRING METHODS TEMPERATURE CODE T6 T4A FOR N2800 OPTION NOTE NP300 UNITS SUITABLE FOR USE IN CLASS DIVISION 2 GROUPS B C AND D HAZARDOUS LOCATIONS OR NONHAZARDOUS LOCATIONS ONLY FOR USE ON A FLAT SURFACE OF A TYPE 1 ENCLOSURE WITH PROVISIONS FOR CLASS I DIVISION 2 WIRING METHODS TEMPERATURE CODE T6 T4A FOR N2800 OPTION Document No DOC IPC 003 User Manual iPC Series amp nPC300 Rev B Rel 12 2013 Page 10 of 24 NOTE RACK MOUNT VERSIONS SUITABLE FOR USE IN CLASS I DIVISION 2 GROUPS A B C AND D CLASS II DIVISION 2 GROUPS F AND CLASS III HAZARDOUS LOCATIONS OR NONHAZARDOUS LOCATIONS ONLY FOR RACK MOUNT INSTALLATION ON A TYPE 1 ENCLOSURE WITH PROVISIONS FOR CLASS I DIVISION 2 WIRING METHODS TEMPERATURE CODE T6 FOR N2800 OPTION WARNING EXPLOSION HAZARD SUBSTITUTION OF ANY COMPONENTS MAY IMPAIR SUITABILITY FOR CLASS I DIVISION 2 WARNING EXPLOSION HAZARD DO NOT DISCONNECT EQUIPMENT WHILE THE CIRCUIT IS LIVE OR UNLESS THE AREA IS KNOW TO BE FREE OF IGNITABLE CONCENTRATIONS WARN2. D PIN NUNBER 100 VAC 240 VAC INPUT 18 VDC 36 VDC INPUT PAC tine Input DC Input Neutral Return DC Return FRONT VIEW Protective Earth Ground Protective Earth Ground Document No DOC IPC 003 User Manual iPC Series amp nPC300 Rev B Rel 12 2013 Page 15 of 24 NOTE WHEN USING USB CONNECTIONS THE USE OF THE USB RETENTION BRACKET IS REQUIRED FOR HAZARDOUS LOCATIONS AND HIGHLY RECOMMENDED FOR NONHARDAOUS LOCATIONS NOTE TO PREVENT INADVERTENT DISCONNECTION OF VIDEO AND OR SERIAL TOUCHSCREEN CABLES ASSURE THAT THE THUBSCREWS ARE SUFFICIENTLY TIGHTENED WARNING EXPLOSION HAZARD DO NOT DISCONNECT EQUIPMENT WHILE THE CIRCUIT IS LIVE OR UNLESS THE AREA IS KNOW TO BE FREE OF IGNITABLE CONCENTRATIONS WARNING EXPLOSION HAZARD DO NOT DISCONNECT THE USB PORTS UNLESS THE POWER HAS BEEN SWITCHED OFF AND THE AREA IS KNOWN TO BE NON HAZARDOUS Document No DOC IPC 003 User Manual iPC Series amp nPC300 Rev B Rel 12 2013 Page 16 of 24 Protective Cover Installation 7 Optional if desired Step 1 Gather the parts of the protective cover top shell bottom shell label insert and wire tie The picture shows wire tie top label insert right bottom shell left and top shell lower right Step 2 Insert your pre wired connector with the screws facing up into the bottom shell
3. See manual for cable wiring instructions Step 3 Insert the wire tie from the bottom shell loop around the cable and come back out of the opposite hole in the bottom shell Step 4 Tighten the wire tie around the cable and the bottom shell Step 5 Seat the top shell onto the bottom as shown Insert label strip if desired in slot on top shell and bottom shell Step 6 Snap the top and bottom shells together Document No DOC IPC 003 User Manual iPC Series amp nPC300 Rev B Rel 12 2013 Page 17 of 24 Connecting Power to Enclosed EN units The enclosed iPC Series are powered from 100 240 VAC 50 60 Hz only Because these are stand alone Type 1 devices and do not require an additional NEMA type enclosure a different type power connection is required These units use a more standard IEC type power cord like found on most computers There is a retention clip that can be utilized to help retain the cord from falling out A US three prong cord is supplied If another country connection method is required then an appropriate UL recognized power cord can be chosen locally not supplied by Nematron Optionally available is an IEC type connector that can be directly wired to for field wiring This can be ordered separately from Nematron and is part number PWR AC EN m Enclosed ePC Series IEC Power Cable Power Cable Retention Clip Installed I O Cable Management The iPC Series units include retention mechanisms for
4. 1200 or nPC300 that can be utilized to strain relief cables This is a flat bracket attached by 2 screws which can be utilized to hold down cables or provides an attachment point for a cable tie to be used for securing cables Care should be taken to provide an adequate radius for any cable being utilized Too tight a radius can damage the conductors When tightening this securing bar care should be taken not to over crush cables this can damage conductors rt j 5 a Cable Securing Bar Installed NOTE WHEN USING USB OR HDMI CONNECTIONS THE USE OF THE RETENTION BRACKETS IS REQUIRED FOR HAZARDOUS LOCATIONS AND HIGHLY RECOMMENDED FOR NONHARDAOUS LOCATIONS NOTE TO PREVENT INADVERTENT DISCONNECTION OF VIDEO AND OR SERIAL TOUCHSCREEN CABLES ASSURE THAT THE THUBSCREWS ARE SUFFICIENTLY TIGHTENED WARNING EXPLOSION HAZARD DO NOT DISCONNECT EQUIPMENT WHILE THE CIRCUIT IS LIVE OR UNLESS THE AREA IS KNOW TO BE FREE OF IGNITABLE CONCENTRATIONS WARNING EXPLOSION HAZARD DO NOT DISCONNECT EQUIPMENT UNLESS THE POWER HAS BEEN SWITCHED OFF OR THE AREA IS KNOWN TO BE NON HAZARDOUS USB AND HDMI CONNECTIONS MUST BE SECURED WITH INCLUDED RETENTION BRACKETS SEE INSTALLATION INSTRUCTIONS Document No DOC IPC 003 User Manual iPC Series amp nPC300 Rev B Rel 12 2013 Page 19 of 24 Drive Removal and Replacement These products are equipped with an easily removable SATA drives They are designed so that there Is no need to
5. Document No DOC IPC 003 User Manual iPC Series amp nPC300 Rev B Rel 12 2013 Page 14 of 24 Connecting Power to the iPC Series Connecting power to the Panel Mount Rack Mount and nPC300 units The iPC Series and nPC300 units are powered from 100 240 VAC 50 60 Hz or optionally from 24 VDC Damage will occur if 100 240 VAC power is connected to an iPC Series unit equipped with the 24 VDC input power option iPC Series equipped units with the 24 VDC option will have a DC suffix in their model number such as iPC1500T i5 4GB 80SS W7 DC Because the iPC Series not EN option is UL 1604 listed for Hazardous Location use Class Division2 Groups A B D Class ll Division 2 Groups F G Temperature Code T6 or T4A the units do not have a power switch for switching off supplied power Consideration should be give to the installation of an appropriately rated external power switch if the application requires powering off the iPC Series unit Power is connected to the units through a removable Phoenix Contact plug Phoenix Contact P N 1777992 that allows for screw termination of field wiring This plug is included with each unit and is keyed to prevent installation in a unit with the wrong input voltage rating When Field Wiring to these terminals the use of 18 AWG or greater 12 AWG maximum copper wire with 602 or 60 75 C wire insulation and the terminal tightening torque of 7 0 Ib in 0 79 Nm is required The termin
6. MB Cache 2 Cores amp 2 Threads o Intel ib 520M 2 4 GHz 3 MB Cache 2 Cores and 4 Threads o Intel i7 620M 2 66 GHz 4 MB Cache 2 Cores and 4 Threads e DRAM Options up to 4 GB e 80 GB minimum easily removable SATA solid state drive o Larger Solid State SATA drive upgrade options o 500 GB min SATA hybrid hard drive with Solid State Adaptive Memory Cache Option Numerous I O Ports Two Gigabit Ethernet ports 6 USB 2 0 ports 4 on N2800 CPU option 2 RS 232 serial port 1 RS 422 485 Serial port Analog VGA or HDMI port for dual screen applications e 508 and ANSI ISA 12 12 01 2012 listed for Hazardous Locations Class I Division 2 Groups A B C D and Class ll Division 2 Groups F and G Class Ill when installed in a NEMA Type 1 4 4x 12 enclosure N A to Enclosed Options NEMA 4 4 12 front bezel 2 Year warranty European CE mark compliant Contains no Lead Integral 100 240 VAC power supply oimplified installation with no studs Ultra Thin design less than 3 25 behind front panel VESA compliant all modes up to SXGA 75Hz SVGA on 12 and XGA on 15 unit Optional 5 wire resistive touch screen Optional NEMA 1 Enclosure Optional 304 stainless steel front bezel Optional iPC1900 Rack Mount front bezel not NEMA sealed Optional 24 VDC input power Windows 7 Professional 32 bit standard o Windows XP Professional 32 bit optional o Windows 7 Ultimate 64 bit includes multi language support optional O O O O O Documen
7. create a system recovery disk This disk is very specific to the platform and options that are included on your unit Do not attempt to use a recovery from one type of unit on another it may not work This recovery disk installs the factory image with all drivers installed On these units you will need an USB DVD ROM Follow the instructions on the recovery DVD for installation When installing the image from this DVD it will not be Activated unlike when you received the unit You may need to set the video resolution after loading the image depending on the unit you are loading Windows 7 Professional 32 bit and Windows 7 Ultimate 64 bit Windows 7 Professional and Ultimate are also supplied with a recovery disk as is done with Windows XP see XP section above This recovery disk installs the factory image with all drivers installed On these units you will need an USB DVD ROM Follow the instructions on the recovery DVD for installation When installing the image from this DVD it will not be Activated unlike when you received the unit You may need to set the video resolution after loading the image depending on the unit you are loading Document No DOC IPC 003 User Manual iPC Series amp nPC300 Rev B Rel 12 2013 Page 21 of 24 Chapter 3 iPC CPU and BIOS Consult the appropriate iPC Series CPU Board User manuals for more detailed specifications of the CPU board and BIOS details This section will concentrate on the features of t
8. inside the same enclosure To install the computer make a cutout according to the diagrams below in one of the walls of your NEMA enclosure Next hold the unit in place while you install the mounting clips Tighten the clips to the point were the back of the unit s front bezel just begins to contact the front of the NEMA enclosure The use of an adjustable torque driver is recommended The screws should be tightened to 8 inch pounds Tighten the clips in a cross pattern This will help to develop an even pressure on the sealing gasket DO NOT OVER TIGHTEN AS DAMAGE CAN RESULT IN THE COMPUTER CAUSING LOSS OF SEALING INTEGRITY w IPC1200 IPC1500 IPC1700 IPC1900 Cutout 9 68 x 12 10 12 00 x 15 00 13 70 x 16 35 14 90 x 17 75 245 9 805mm 848mm 378 5mm H x W 307 3mm 381mm 415 3mm 450 9mm 02 W 02 Document No DOC IPC 003 User Manual iPC Series amp nPC300 Rev B Rel 12 2013 Page 12 of 24 Mounting Clip Installation 25 THICK MONITOR nm d FRONT BEZEL COMPRESSABLE SEALING GASKET RT MOUNTING CLIP WITH 10x32 SCREW MAXIMUN ALLOWABLE PANEL THICKNESS FRONT PANEL OF NEMA ENCLOSURE TIGHTEN TO 8 INC
9. installed The iPC Series utilizes a USB connection for the touchscreen therefore the touchscreen will only function with operating systems that can recognize and utilize USB connections The driver included with these units functions with Windows 2000 XP VISTA and Windows 7 If using the nPC300 with a touchscreen monitor the appropriate driver will be included with the monitor Operating System Recovery If for some reason your operating system needs to be reinstalled Nematron provides an Operating System or Recovery disk The procedure for this is dependent on the operating system Because this series does not have an integrated DVD you will need a USB DVD ROM drive In some cases you will also need the Documentation and Driver disk that is included with each unit The IPC Series products are shipped with Windows XP Professional SP3 Windows 7 Professional 32 bit or Windows 7 Ultimate 64 bi The units can also be ordered with No Operating Systems installed Use of other operating systems is not recommended and nol supported Windows XP Professional SP3 for Embedded Systems otandard Windows XP operating system disks are no longer available from Microsoft In order to continue shipping Windows XP for Automation applications Nematron had to switch to a different license scheme Windows XP Professional SP3 for Embedded Systems This is not Embedded XP it is simply a different license procedure By switching to this license Nematron had to
10. sealed when installed Document No DOC IPC 003 User Manual iPC Series amp nPC300 Rev B Rel 12 2013 Page 4 of 24 I O Panel All four versions of the iPC series and the nPC300 have a common Input Output configuration Figure 2 0 shows the base configuration of the iPC Series not Fanless units COM1 COMS3 Input Power RS 232 RS 85422 605820 HOMI Dual Gigabit Ethernet Easily Removable Drive Input Power RS 232 RS 485 422 2 USB 3 0 An HDMI Dual Gigabit 2 USB 2 0 Video Port Port Ethernet Figure 2 0 iPC Series configuration Document No DOC IPC 003 User Manual iPC Series amp nPC300 Rev B Rel 12 2013 Page 5 of 24 Feature Analog Video A standard 15 pin analog VGA is provided This connection allows a second screen Port to be easily added to the iPC In addition the iPC allows this second screen to be utilized in an extended desktop configuration See CPU manual section on configuring the video for more details on this feature HDMI Port An HDMI port is provided This connection allows a second screen to be easily added to the iPC In addition the iPC allows this second screen to be utilized in an extended desktop configuration See CPU manual section on configuring the video for more details on this feature Com 2 is a standard 9 pin RS 232 serial port Com 3 Com 3 utilizes a standard 9 pin serial port The iPC default configuration for this port is RS 485 or RS 422 This po
11. H POUNDS FRONT PANEL OF NEMA ENCLOSURE P x 90222222229 i 8 po Gum IE Ru 2 amp nO r3 c 7 T EU L e I amp H t REAR VIEW OF PANEL MOUNTED ePC NOTE WHEN INSTALLING THE MOUNTING CLIPS TIGHTEN THE SCREWS TO 8 10 INCH POUNDS MAXIMUM OVERTIGHTENING THE SCREWS WILL RESULT IN A COMPRIMISED NEMA SEAL AND MAY CAUSE TOUCH SCREEN BREAKAGE Document No DOC IPC 003 User Manual iPC Series amp nPC300 Rev B Rel 12 2013 Page 13 of 24 nPC300 Unit Installation The nPC300 is intended to be mounted on the flat surface on the inside of a NEMA Type 1 4 4x or NEMA 12 enclosure See the specifications section for the dimensions and mounting dimensions required for mounting this unit When selecting an enclosure remember to allow adequate space around the computer for good air flow Do not block air flow around the unit except for the mounting surface
12. ING EXPLOSION HAZARD DO NOT DISCONNECT THE USB PORTS UNLESS THE POWER HAS BEEN SWITCHED OFF AND THE AREA IS KNOWN TO BE NON HAZARDOUS NOTE ENCLOSED IPC VERSIONS A LISTED VESA STYLE MOUNT SUITABLE WITH A MINIMUM LOAD RATING OF 40 POUNDS SHALL BE USED IN THE END INSTALLATION FOR USE IN NONHAZARDOUS LOCATIONS ONLY TYPE 1 ENCLOSURE Document No DOC IPC 003 User Manual iPC Series amp nPC300 Rev B Rel 12 2013 Page 11 of 24 Chapter 2 Installation of Computer Panel Mount iPC Series Unit installation The panel mount versions of the IPC Series are intended to be mounted in and used where NEMA 1 NEMA 4 4x and NEMA 12 type enclosures are employed Enclosures made of heavier gauge metal work better because they won t deform or bend as easily when the monitor s sealing gasket is compressed The monitor meets NEMA 4 12 sealing specifications when properly installed in an approved NEMA enclosure constructed from 14 gauge or heavier steel The computer uses U shaped clips and a special gasket to achieve the proper seal When selecting an enclosure remember to allow adequate space around the rear of the computer for good air flow Do not block air flow from below or above the monitor If possible mount the computer in a vertical orientation The unit is designed to work in environments up to 50 degrees Centigrade ambient temperature inside the enclosure Remember to account for heat dissipated from other equipment that may be installed
13. Tal AERE aliit p zn iPC Series amp nPC300 Ultra Thin Industrial Computers w i Processors User s Guide Document No DOC IPC 003 N t User Manual iPC Series amp nPC300 Rev A Rel 10 2012 e la Revision List Description of Change Release Date Preliminary Release 8 2012 EI Added ATOM N2800 and EN Options 12 2013 Nematron reserves the right to make changes in specifications described herein at any time without notice in order to improve design and reliability Nematron does not assume any responsibility for the use of any circuitry described no circuit patent licenses are implied Nematron assumes no responsibility for damage caused by misuse or improper use of its products WARRANTY Nematron warrants to Customer that the Products will be free from defects in material and workmanship under normal use and service for a period of two years from date of invoice Customer s exclusive remedy for breach of this warranty is that Nematron will either i repair or replace at its option any Product which fails during the warranty period because of such defect if Customer promptly reported the failure to Nematron in writing or ii if Nematron is unable to repair or replace Nematron will refund the purchase price of the Product upon its return to Nematron This warranty does not apply to any Product which has been subjected to misuse abnormal service or handling or which has been altere
14. The computer can be mounted on a horizontally or vertically to a wall or shelf within the enclosure The unit is designed to work in environments up to 50 degrees Centigrade ambient temperature inside the enclosure Remember to account for heat dissipated from other equipment that may be installed inside the same enclosure Rack Mount Unit Installation The iPC1900 with a rack mount front panel is intended to be mounted to a 19 0 wide rack in a NEMA Type 1 or better enclosure The unit can be mounted using standard rack mount hardware not supplied via the eight 4 each side counter bored holes in the front of the panel The front panel is intended to be mounted in a vertical height of 9 U 16 07 on the rack This unit is not NEMA sealed when mounted like the panel mount versions When selecting an enclosure remember to allow adequate space around the rear side of the computer for good air flow The unit is designed to work in environments up to 50 degrees Centigrade ambient temperature inside the enclosure Remember to account for heat dissipated from other equipment that may be installed inside the same enclosure Enclosed Unit Installation The enclosed iPC Series products are intended to be stand alone NEMA Type 1 units These are required to be mounted to a VESA style mount with a minimum load rating of 40 pounds A desktop stand wall mount or articulating arms are examples of VESA style mounts that can be utilized These units are vented
15. al screws are shown in Top View below Connect the field wiring according to the appropriate voltage in the table below Strip the wire insulation back on each conductor 6 5 mm 0 26 in and assure that the remaining wire is twisted together not frayed and clean If an outer jacket over each conductor is utilized then strip the outer jacket back an additional 19 0 mm 0 75 in as shown in figure below When installing the conductors take care that there are not any stray strands of wire that can contact an adjoining connection Tinning of each lead can be utilized to prevent frays if desired Optionally the included protective cover can be utilized to prevent electrical shocks when handling the power connector and provide strain relief for each conductor connection see the following section for installation instructions After the connections are made make sure the plug retention screws the two screws shown in the Front View below are securely tightened This will prevent the plug from pulling out The use of these screws is mandatory when the unit is utilized in applications requiring hazardous locations approvals co Comm 2 2 FRONT VIEW IIIN 5559 60000000 ee dC eels 9
16. d or modified in design or construction or which has been serviced by anyone other than Nematron The warranty set forth herein is in lieu of and exclusive of all other warranties express or implied Document No DOC IPC 003 User Manual iPC Series amp nPC300 Rev B Rel 12 2013 Page 2 of 24 Chapter 1 Introduction The iPC Series products are high performance embedded ultra thin industrial computers specifically designed for harsh industrial environments including Class amp Il Division 2 Hazardous Locations The iPC Series offers four versions with 12 1 SVGA 800 x 600 15 XGA 1024 x 768 17 SXGA 1280 x 1024 or 19 5 1280 x 1024 LED backlit TFT Color LCD panels A stand alone node version without an integrated display is also available nPC300 These high performance embedded industrial PCs offer processor options up to a state of the art Intel Core i7 Processor and DRAM options up to 4 GB With a multitude of I O included on the standard unit many automation applications are ideally suited for use with this series Ultra Thin panel depth 2 7 to 3 42 also makes this series ideal for space constrained applications With Class and ll Division 2 approvals this industrial PC makes installation in Hazardous Locations applications simple Features e Processor Options up to Intel i7 options o Intel N2800 1 86 GHz 1 MB Cache 2 Cores amp 4 Threads Fanless o Intel Celeron P4500 1 86 GHz 2
17. for air flow and are not dust or water proof Care should be taken to not utilize these units in areas where high concentration of particulate matter or moisture are present lf these conditions do exist then the use of the panel mount versions in an appropriate NEMA 4 4x or 12 enclosure should be considered The warranty may be voided if high levels of moisture or particulate matter are determined to be the cause of a failure The ePC Series EN units except fanless version have a filter over the CPU fansink to filter incoming air This filter should be carefully removed and cleaned periodically depending on service conditions some applications this may need to be checked and cleaned often These units are designed to work in environments up to 50 degrees Centigrade ambient temperature around the enclosure Impeding the airflow around this unit or clogged filters will severely affect the reliability of the unit by raising the internal temperature Assure that there is adequate airflow around the unit NEMA Type 1 is not sealed against water and or dust it is simply provides protection from operators shocking themselves lt also offers a certain amount of fire containment it the event of a catastrophic failure inside the unit As stated previously NEMA 1 is not waterproof or dust proof and is not intended to be utilized in environments exhibiting high levels of these conditions Example of an Enclosed Unit Mounted To an Articulating Arm
18. he iPC Series units that are externally accessible External I O Connections The following figure shows the externally accessible connections COM1 COM2 COMS3 Input Power RS 232 RS 485 422 805820 o HDMI Dual Gigabit Ethernet ott Port Easily Removable Drive Input Power RS 232 RS 485 422 2 USB 3 0 Ana HOMI Dual Gigabt 2USB20 Port s Document No DOC IPC 003 User Manual iPC Series amp nPC300 Rev B Rel 12 2013 Page 22 of 24 Pinouts With Celeron i5 and i7 Options COM 1 RS 232 COM 2 RS 232 COM 3 RS 485 422 COM 1 amp 2 12345 USB USB T ON eres o Jo oS Je nis oS Je 254 JO 2 RD o e USB USB 3 TxD _ Er m s alls EA Ez gt UNT Pinouts With Intel N2800 Option Only COM 1 RS 232 COM 2 RS 232 COM 4 RS 485 422 COM 1 amp 2 PIN SIGNAL eo oo 7 oh644 7 RD tq eo oo Vd Je EAZ EAZ 3 TD USB 2 0 USB 3 0 5 GND I 6 DSR TxD o 6 8 CTS D o 6 22 9 RI LJ USB 2 0 USB 3 0 Document No DOC IPC 003 User Manual iPC Series amp nPC300 Rev B Rel 12 2013 Page 23 of 24 This page intentionally left blank Document No DOC IPC 003 User Manual iPC Series amp nPC300 Rev B Rel 12 2013 Page 24 of 24
19. of the nPC300 unit are as follows Document No DOC IPC 003 User Manual iPC Series amp nPC300 Rev B Rel 12 2013 Page 8 of 24 ELECTRICAL Input Power nPC300 60 W Typical 40 W for N2800 Option IPC1200 70 W Typical 50 W for N2800 Option IPC1700 80 W Typical 60 W for N2800 Option IPC1700 85 W Typical 65 W for N2800 Option IPC1900 90 W Typical 70 W for N2800 Option Typical Power is measured without any additional I O or expansion options Any additional I O installed during application can increase this value ENVIROMENTAL Operating Temperature 0 C to 55 50 C for Enclosed Options 20 to 80 RH non condensing Operating Vibration 5 2000 Hz 0 006 peak to peak displacement 1g maximum acceleration Non Operating Vibration 5 2000 Hz NENNEN Operating Altitude Sea level 10 000 feet Non Operating Altitude Sea level 40 000 feet 1 Shock and Vibration specifications are established using Solid State drives and non rotating media 2 Altitude Specification is established by using all internal component specifications Document No DOC IPC 003 User Manual iPC Series amp nPC300 Rev B Rel 12 2013 Page 9 of 24 AGENCY Front Panel NEMA Rating NEMA 4 4X 12 IP65 EU CE Marking Compliance CE EN 55022 Class A EN 61000 3 2 Class A EN 61000 3 3 EN 61000 6 2 Safety Agency Approvals UL 508 Listed cUL Listed CSA C22 2 142 ANSI ISA 12 12 01 2012 Listed amp
20. remove the cover on these units to change a drive There is no reason to remove the rear cover from the unit The drive is simply removed by loosening the two thumbscrews and pulling the drive out Remove all power to the unit before removing the drive There are no cables to remove when pulling the drive from the chassis Once the drive is removed there are four screws on the back of the bracket that hold the drive If the drive is being replaced these screws secure the drive to the plate To reinstall the drive simply insert the bracket with drive attached into the chassis and slide forward Completely push the drive in and secure the thumbscrews before reapplying power to the unit Solid State Drives mount directly to the bracket however a thin plastic insulator is required to be inserted between the bracket and a standard rotating media hard drive When the unit is ordered with a rotating hard drive these insulators are pre installed Various drive options with a mounting bracket pre installed are available for purchase from Nematron If a spare drive is required these are recommended These spare drives can be used with third party software to create complete system backups for your installation Drive Removal Document No DOC IPC 003 User Manual iPC Series amp nPC300 Rev B Rel 12 2013 Page 20 of 24 Installing the Touch Screen Driver Software If your iPC is ordered with a touchscreen and an operating system the drivers will be pre
21. rt automatically switches between 485 and 422 depending on the connections utilized See CPU manual for more detailed instructions and information on the configuration of this port communications 2 USB 2 0 and 2 USB 3 0 on ATOM N2800 unit only Input Power Input power whether AC or DC is supplied via a Phoenix connector See Chapter 2 on Installation for more details on how to wire this connection Easily Removable An easily removable high speed Serial ATA drive is provided The captive retention SATA Drive hardware lack of cumbersome cables and handle make changing hard drives an easy task DISPLAY 222 ePC1200 ePC1500 ePC1700 ePC1900 Display Diagonal 12 1 307 34mm 15 0 381 0mm 17 0 431 8mm 19 0 482 6mm Display Size 9 69 x 7 26 11 97 x 8 98 13 30 x 10 64 14 82 x 11 85 Active Area 246 0mm x 304 0mm x 337 8mm x 376 4 x HxV 184 5mm 228 1mm 270 3mm 301 0mm Native Resolution SVGA 800x600 XGA 1024 x 768 SXGA 1280 x wA 502 1024 1024 Colors Brightness 450 Nit 400 Nit 350 Nit 300 Nit Typical Contrast Ratio 600 1 600 1 1000 1 2000 1 Typical Horizon Vertical View Angle 140 120 140 120 170 170 178 178 gt 5 Typical Backlight Life 50 000 hrs 50 000 hrs 50 000 hrs 50 000 hrs Typical Document No DOC IPC 003 User Manual iPC Series amp nPC300 Rev B Rel 12 2013 Page 6 of 24 TOUCH SCREEN Optional Touch Screen Technology 5 Wire Analog Re
22. securing USB and HDMI cable connections USB and HDMI connections are not secure and can easily fall out Use of the brackets is suggested for all applications and is required for any hazardous locations installations Simply remove the bracket s insert your USB and or HDMI cables through the bracket Connect your cables to the unit and move the bracket into position Snugly push the bracket toward the USB and or HDMI connector and secure with the screws provided On the iPC panel mount and Rack Mount units the USB and HDMI brackets are simple L shaped brackets with cutouts to retain up to six USB cables and one HDMI connector On the nPC300 the there are three pieces one flat piece is secured to the bottom of the unit using two 4 40 screws and then the other two brackets are the same as on the iPC unis nPC300 USB and HDMI Retention Brackets iPC Series HDMI amp USB Retention Bracket With HDMI amp USB Cables Installed Document No DOC IPC 003 User Manual iPC Series amp nPC300 Rev B Rel 12 2013 Page 18 of 24 Video and the Serial connections have jack screws in the connectors that can be utilized to secure your cable end to the unit Ethernet connections have a plastic tab that prevents the connection from falling out See the connecting power section for details on securing the power connections In addition to the USB and HDMI Brackets there is an additional cable management bracket at the bottom of the units N A on IPC
23. sistive Interface Internally via USB Resolution 4096 x 4096 Positional Accuracy Maximum Error 0 18 0 19 ePC1900 4 57mm 4 83mm 1900 Positional Accuracy Standard Deviation of Error 0 08 2 0 mm Expected Life gt 35 000 000 Activations Document No DOC IPC 003 User Manual iPC Series amp nPC300 Rev B Rel 12 2013 Page 7 of 24 PHYSICAL I iPC1200 iPC1500 iPC1700 iPC1900 10 475 x 12 9 x 12 80 x 15 80 x 14 48 x 17 14 x 15 70 x 18 66 x Over All 3 42 2 95 3 10 3 25 266 1mm x 325 1mm x 367 8mm x 398 8mm x H x W x D 32 2mm x 401 3mm x 442 0mm x 474 0mm x 86 75mm 74 9 78 7mm 82 6mm Panel Mounting Depth Cutout 9 68 x 12 10 12 00 x 15 00 13 70 x 16 35 14 90 x 17 75 245 9mm x 305mm x 348mm x 378 5mm x H x W 307 3mm 381mm 415 3mm 450 9mm 10 5 lbs 4 76kg 15 01bs 6 80kg 19 0 Ibs 8 63kg 22 5 Ibs 10 22kg um 14 0 lbs 6 35kg 19 5 lbs 8 84kg 23 5 lbs 10 67kg 27 5 Ibs 12 49kg mcm 2 5 lbs 1 13kg 3 5 lbs 1 58kg 3 75 lbs 1 70kg 44 0 Ibs 1 81kg The nPC300 is essentially the rear of the panel mount versions It is supplied with mounting brackets so that it can be easily attached to wall or shelf in a NEMA 1 or better enclosure The nPC300 is not a standalone device and must be installed in an enclosure to protect operators 3 165 80 4mm 2 70 68 6mm 2 90 73 7mm 3 00 76 2mm The dimensions
24. t No DOC IPC 003 User Manual iPC Series amp nPC300 Rev B Rel 12 2013 Page 3 of 24 Specifications Front Panels The iPC series has NEMA 4 4X 12 sealed front panels when mounted in an appropriate NEMA rated enclosure The front panels and required cutouts are exactly the same as the appropriate size ePC Series or M Series units for easy migration to the iPC Series from the other units See Chapter 2 for more details on installation and selection of an appropriate enclosure All four sizes have very similar front panels with different dimensions 1287 IPC1500 1290 Le 296 fe i 14 8 15 707 iPC1 00 Figure 1 0 iPC Series Front Panel Comparison The standard front panels are powder coated aluminum The optional Stainless Steel front panel is type 304 and will not contain a logo pocket or logo on the front The window area is clear polycarbonate when ordered without a touchscreen The touchscreen option is chemically strengthened glass covered by a polyester overlay The polyester overlay has better resistance to chemicals than the polycarbonate window Depending on the chemicals involved in your application consideration should be given to choosing the proper window material In addition there is a Rack Mount front panel option for the iPC1900 19 unit only This front panel is powder coated aluminum and is 9U high with four rack mount spaced counter bored mounting holes on each side of the panel This panel is not NEMA
Download Pdf Manuals
Related Search